Panasonic Nn-Cs596a nn-cs596s PDF
Panasonic Nn-Cs596a nn-cs596s PDF
Panasonic Nn-Cs596a nn-cs596s PDF
PHAMOS0609045C3
Microwave Oven
NN-CS596A / NN-CS596S
HPE(Hong Kong)
YPQ(Singapore)
MPQ(Malaysia)
YTE(Others)
KTE(UAE)
PTE(Iran)
QPQ(Australia & New Zealand)
ZPE(CIS Countries)
SPECIFICATIONS
1
2006 Panasonic Home Appliances Microwave Oven (Shanghai)
Co., Ltd. / All rights reserved. Unauthorized copying and
distribution is a violation of law.
2
3
4
1. SCHEMATIC DIAGRAM
5
2. DESCRIPTION OF OPERATING SEQUENCE
2.1. Variable power cooking control
High Voltage Inverter Power Supply (U) controls output power by the signal from Digital
Programmer Circuit (DPC). Power relay always stays ON, but PWM (pulse width modulation)
signal controls microwave output power.
NOTE:
6
The ON/OFF time ratio does not correspond with the percentage of
microwave power since approximately 2 seconds are required for
heating of magnetron filament.
Variable Power Cooking
POWER SETTING OUTPUT MANUAL
POWER(%) MICROWAVE DUTY
APPROX. ON(SEC) OFF(SEC)
HIGH 100% 22 0
MEDIUM-HIGH 70% 22 0
MEDIUM 55% 22 0
MEDIUM-LOW 40% 22 0
LOW 20% 13 9
DEFROST 30% 17 5
7
When the Auto Control feature is selected and the Start pad is tapped:
2. When cooking time in the display window has elapsed, the oven
turns off automatically by a control signal from the digital
programmer circuit.
2.4. Convection & Grill Convection cooking control
The digital programmer circuit controls the ON-OFF time of the heater in order to control oven
cavity temperature.
8
NOTE:
- For "CONVECTION" function, after preheating, RY9 would no
longer be switched to ON.
- For "GRILL CONVECTION" function after preheating, RY9 would
always stay ON even if the oven temp exceeds the set temp.
NOTE:
9
cooking categories, power relay RY1 always stay on, but RY9's ON-
OFF time as shown in Figure.
COMBINATION GRILL(RY9) MICROWAVE
CATEGORY ON (sec.) OFF (sec.) (RY1)
1 33 0 ON
2 24 9 ON
3 18 15 ON
2.7. IR reheat
The temperature of food being heated is detected by an infrared (IR) sensor and you do not have
to set time.
2.7.2. Operation
IR sensor is mounted on top right of oven cavity through the hole. It scans all over cooking shelf.
IR sensor has 8 eyes and can read oven shelf left to right at the time. Then IR sensor is designed
to scan front to back to cover all over shelf. (19 points)
10
2.8. Steam function (micro steam)
2.8.1. Water Supply
Water in water tank will be pumped out and supply to the steam generation heater located inside
back bottom of oven cavity.
2.8.2. Operation
When pressing [start] pad, oven preheat will start and then water supply begins. It will take 1
minute for preheating. When preheat is completed, it will turn into actual cooking process. During
heating, the temperature sensor (Thermistor) located on steam heater will monitor steam heater
temperature and when it exceeds 200°C, the additional water will be supplied to maintain
moisture/steam within oven cavity.
11
3. CAUTIONS TO BE OBSERVED WHEN /
TROUBLESHOOTING
Unlike many other appliances, the microwave oven is a high voltage, high current device. It is
free from danger in ordinary use, though extreme care should be taken during repair.
CAUTION
Servicemen should remove their watches whenever working close
to or replacing the magnetron.
3.1. Check the grounding
Do not operate on a two wire extension cord. The microwave oven is designed to be grounded
when used. It is imperative, therefore, to ensure the appliance is properly grounded before
beginning repair work.
12
H.V. Inverter warning
13
Discharging the high voltage capacitors
WARNING
There is high voltage present with high current capabilities in the
circuits of the primary and secondary windings, choke coil and heat
sink of the inverter. It is extremely dangerous to work on or near
these circuits with the oven energized. DO NOT measure the voltage
in the high voltage circuit including the filament voltage of the
magnetron.
WARNING
Never touch any circuit wiring with your hand or with an insulated
tool during operation.
3.3. Confirm before repair
1. Before repair or replacement of parts, ensure to take out the water
tank from microwave oven. Further more, use drainage function,
to drain the water remaining in the water pipes and tubes into oven
cavity.
2. Wipe up the oven cavity.
WARNING
Before beginning repair work, make sure that there is no water in
microwave oven, otherwise the water might invade the electric parts
and will cause short circuit even result in electric shock.
3.4. Part replacement
When any part or component is to be replaced, always ensure that the power cord is removed
from the wall outlet.
14
3.5. When the 10A fuse is blown due to the operation of the short
switch
WARNING
When the 10A 220V fuse is blown due to the operation of the interlock monitor switch, replace all
of the components (primary latch switch, short switch and power relay B (RY1)).
3.6. Avoid inserting nails, wire etc. through any holes in the unit
during operation
Never insert a wire, nail or any other metal object through the lamp holes on the cavity or any
holes or gaps, because such objects may work as an antennaand cause microwave leakage.
IMPORTANT NOTICE
The following components have potentials above 2000V while the appliance is operated.
- Magnetron
- High voltage transformer (Located on inverter (U))
- High voltage diodes (Located on inverter (U))
- High voltage capacitors (Located on inverter (U))
Pay special attention to these areas.
15
When the appliance is operated with the door hinges or magnetron installed incorrectly, the
microwave leakage can exceed more than 5mW/cm2. After repair or exchange, it is very important
to check if the magnetron and the door hinges are correctly installed.
IMPORTANT NOTICE
After repair or replacement of parts, make sure that all the water pipes and tubes are properly
connected, otherwise the water might invade the electric parts and will cause short circuit even
result in electric shock.
CAUTION
After repair or replacement of parts, make sure that
all the water pipes and tubes are properly
connected, otherwise the water might invade the
electric parts and will cause short circuit even
result in electric shock.
4.1. Magnetron
1. Discharge the high voltage capacitor.
2. Remove 2 screws holding reinforce bracket A on oven cavity.
16
3. Remove 2 screws holding reinforce bracket B on oven cavity.
17
plate respectively, then remove air guide B.
10. Disconnect 2 lead wires from fan motor terminals.
11. Disconnect lead wires from noise filter (U) terminals.
12. Release locking tabs of reinforce bracket A hanging on both
sides of oven cavity, then withdraw the reinforce bracket A outside
slightly.
NOTE:
Pay attention to the sharp edges of reinforce bracket A.
13. Hold the reinforce bracket A, then remove 4 screws holding
magnetron.
NOTE:
After replacement of the magnetron, tighten mounting screws
properly in an x pattern, making sure there is no gap between the
waveguide and the magnetron to prevent microwave leakage.
CAUTION
When replacing the magnetron, be sure the
antenna gasket is in place.
CAUTION
When connecting 2 filament lead wires to the
magnetron terminals, be sure to connect the lead
wires in the correct position. The lead wire of high
volatge transformer should be connected to “F
terminal” and the lead wire from high voltage
capacitor should be connected to “FA terminal”.
18
4. Remove wiring connectors CN3, CN4, CN6, CN8, CN9 and all
connectors connecting to power relays from D.P.C. board HU.
19
completely from escutcheon base.
NOTE:
1. The membrane key board is attached to the escutcheon base with
double faced adhesive tape. Therefore, applying hot air such as
using a hair dryer is recommended for smoother removal.
2. When installing new membrane key board, make sure that the
surface of escutcheon base is cleaned sufficiently so that any
problems (shorted contacts or uneven surface) can be avoided.
20
Do not use a soldering iron or desoldering tool of more than 30
watts on D.P.C. contacts.
6. With all the terminal pins cleaned and separated from D.P.C.
contacts, remove the defective transformer/power relays. Replace
components making sure all terminal pins are inserted completely,
then resolder all terminal contacts carefully.
21
13. Remove 2 screws holding H.V. Inverter on Inverter bracket.
22
1. Remove left and right door key springs from door arm with plier.
NOTE:
Please support door before operation.
23
reassemble it properly and adjustment so as to prevent an
excessive microwave leakage. Adjustment of the door
assembly(Refer page 22).
2. When mounting the door to the oven, be sure to adjust the door
parallel to the cavity front plate by moving hinges back or front.
NOTE:
Upper portion of door A should firmly touch the cavity front plate
without pushing.
4. Remove fan blade from fan motor shaft by pulling it straight out.
4.8. Pump
1. Remove water tank from escutcheon base.
2. Keep pressing [Steam/Deforst] pad for more than 2 seconds to
drain the water remaining in the water pipes and tubes into oven
cavity.
3. Pull out tube A connecting to pump from copper pipe.
4. Remove all wiring connectors from D.P.C board AU.
5. Remove 1 grounding screw holding on cavity front plate.
6. Open the door of oven, slide the escutcheon base upward and out
24
slightly.
7. Pull out tube B from inlet of pump.
8. Remove 2 screws holding pump bracket on escutcheon base.
10. Uplift the afterbody of pump slightly to release the tabs of pump
bracket, then draw out pump.
To install pump
25
harness clasp of pump bracket).
2. Please confirm it is located properly after installing.
NOTE:
After repairing, when insert copper pipe into tube A, make sure the
inserted depth is no less than 9 mm to prevent tube A from slipping.
4.9. IR sensor
1. Disconnect connector CN8 from D.P.C. board HU.
2. Remove 1 screw holding IR sensor (U) on right heater panel.
26
To replace swing motor of IR sensor
27
NOTE:
After removing the motor cover, be sure that cut portions are
properly trimmed or bent to the Inside so that no sharp edges will
be exposed to outside.
2. Disconnect 2 lead wires from stir motor terminals.
3. Remove 2 screws holding stir motor.
NOTE:
After reinstalling the new turntable motor and reconnecting the 2
lead wires, reinstall the motor cover by rotating it around 180,
tucking the 2 tabs under the base in the 2 provided slots, then
screw the single tab to the base using a screw.
28
3. Remove tubes from both ends of copper pipe.
4. Remove 1 screw holding air guide B on the base.
5. Remove left and right door key springs from door arm.
NOTE:
Please support door before operation.
6. Turn over the microwave oven and remove all screws holding
base on oven assy & two hinges.
NOTE:
Do not remove two screws holding left and right hinge on the
bottom of cavity front plate.
To install heater DU
NOTE:
29
1.Please spread silicon grease evenly between the interface of
heater DU and bottom of oven cavity. (about 0.3mm thickness), this
is for good conductibility.
2.Tighten 6 screws and make sure there is no gap between heater
DU and bottom of oven cavity.
3.Do not forget to screw the thermal cutout bracket along with
heater Du.
To install thermistor
NOTE:
Before installing thermistor, please fill enough silicon grease into
the installation hole of heater DU for good conductibility.
30
4. Remove 1 screw holding side cover on the side of back cover,
then remove side cover & circuit breaker.
5. Disconnect 2 lead wires from convection heater terminals.
31
back plate.
32
14. Remove 2 screws holding convection heater on convection
inside cover A.
33
4.13. Circuit breaker
34
CAUTION [NEW. H.V.]
1. High voltage is present at the high voltage
terminal of the High Voltage Inverter (U) including
aluminum heat sink during any cook cycle.
2. It is neither necessary nor advisable to attempt
measurement of the high voltage.
3. Before touching any oven components, or wiring,
always unplug the oven from its power source and
discharge the high voltage capacitors.
5.1. Primary latch switch (door switch and power relay B) interlocks
1. Unplug lead connectors to Power Relay B and verify open circuit
of the power relay B 1-2 terminals.
2. Unplug lead connectors to Primary Latch Switch and Door Switch.
3. Test the continuity of switches at door opened and closed
positions with ohm meter (low scale).
Normal continuity readings should be as follows.
Door Closed Door Opened
Primary Latch switch 0 (Close) (Open)
Door Switch 0 (Close) (Open)
Power Relay B (Close) (Open)
5.3. Magnetron
Continuity checks can only indicate an open filament or a shorted magnetron. To diagnose for an
open filament or shorted magnetron.
35
1. Isolate magnetron from the circuit by disconnecting the leads.
2. A continuity check across magnetron filament terminals should
indicate one ohm or less.
3. A continuity check between each filament terminal and magnetron
case should read open.
Test1
1. Program DPC.
36
A. Press [Timer/Clock] pad twice.
B. Press [Start] pad once.
C. Press [Micro Power] pad once.
2. Place 1 litre of water load into oven cavity.
3. Unplug 2 pin H.V. lead wire connector CN703 from magnetron tube.
4. Program oven at High power for 1 minute and press start.
A. After approximately 23 seconds, oven stops.
B. During oven operation, input current is approximately 0.5 to 1A.
If both a and b are OK, proceed to test 2.
INPUT AMPERE FAILURE CODE
Unplug CN703 0.5 to 1A Oven stops in 23
seconds after
started.
Test2
If both a and b check OK, the Inverter Power Supply (U) can be determined to be OK.
If the resistance reading is out of the range stated here, the thermistor is detective and must be
37
replaced.
5.7. IR Sensor
To test if IR sensor is ok by doing the following procedures.
Test
1. Program DPC.
A. Press [Timer/Clock] pad twice.
B. Press [Start] pad once.
C. Press [Micro Power] pad once.
2. Open the door, then keep pressing [Start] pad for more than 2
seconds until buzzer beeps.
3. Remain door opening and press [Start] pad twice, then "°C" will
be shown on the display.
4. Close the door.
5. Press [Start] pad, IR sensor will swing. After 4 seconds, it will
stop and show max and minimum temperature readings of 8 eyes
IR sensor on display.
6. If the reading is within the limited range of oven temperature, and
all above is ok, you may decide IR sensor functions properly.
7. Press [Stop/Reset] pad to finish the test.
5.8. Circuit breaker
1. Turn the switch of circuit breaker to the "I" position and then plug
in the oven.
2. Press the “TEST” button on circuit breaker, if the switch jump
back to "O" position, you may decide the circuit breaker functions
properly.
38
6. MEASUREMENTS AND ADJUSTMENTS
6.1. Adjustment of Primary latch switch, Secondary latch switch and
Short switch.
1. Mount the Primary latch switch, the Secondary latch switch and
the Short switch to the door hook assembly as shown in
illustration.
NOTE:
No specific individual adjustments during installation of the
Primary latch switch, Secondary latch switch or Short switch to
the door hook are required.
2. When mounting the door hook assembly to the oven assembly,
adjust the door hook assembly by moving it in the direction of the
arrows in the illustration so that the oven door will not have any
play in it. Check for play in the door by pulling the door assembly.
Make sure that the latch keys move smoothly after adjustment is
completed. Completely tighten the screws holding the door hook
assembly to the oven assembly.
3. Reconnect the short switch and check the continuity of the
monitor circuit and all latch switches again by following the
component test procedures.
39
4. The Primary latch switch must be ON when the space between
upper portion of door A and cavity front plate is 2~4mm, if the door
gap is greater than 4mm, the Primary latch switch must be OFF.
40
- Wrist watch or stopwatch
NOTE:
Check the line voltage under load. Low voltage will lower the
magnetron output. Take the temperature readings and heating time
as accurately as possible.
1. Fill the beaker with exactly one litre of tap water. Stir the water
using the thermometer and record the water’s temperature.
(recorded as T1).
2. Place the beaker on the center of glass tray. / Set the oven for High
power and heat it for exactly one minute.
3. Stir the water again and read the temperature of the water.
(recorded as T2).
4. The normal temperature rise at High power level for each model is
as shown in table.
TABLE (1L-1min.test)
RATED OUTPUT TEMPERATURE RISE
1000W Min.8.5°C
7. TROUBLESHOOTING GUIDE
41
DANGER HIGH VOLTAGES
1. DO NOT RE-ADJUST PRESET CONTROL on the H.V.Inverter (U). It is very dangerous to repair or
without proper test equipment because this circuit handles very large current and high voltage. Operating
a misaligned inverter circuit is dangerous.
2. Ensure proper grounding before checking for trouble.
3. Be careful of the high voltage circuitry, taking necessary precautions when troubleshooting.
4. Discharge high voltage remaining in the H.V.Inverter (U).
5. When checking the continuity of the switches or the H.V.Inverter, disconnect one lead wire from these
parts and then check continuity with the AC plug removed. To do otherwise may result in a false
damage to your meter. When disconnecting a plastic connector from a terminal, you must hold the
connector instead of the lead wire and then disconnect it, otherwise lead wire may be damaged or
connector cannot be removed.
6. Do not touch any parts of the circuitry on the digital programmer circuit, since static electric discharge
damage this control panel. Always touch yourself to ground while working on this panel to discharge
static charge in your body.
7. 220/240V AC is present on the digital programmer circuit (Terminals of power relay’s and primary
Digital Programmer Circuit). When troubleshooting, be cautious of possible electrical shock hazard.
Before troubleshooting, operate the microwave oven following the correct operating procedures
in the instruction manual in order to find the exact cause of any trouble, since operator error may
be mistaken for the oven’s malfunction.
Oven has self diagnostic function but it will not be activated in normal operation mode.
To show self diagnostic result, please take the following steps.
1. Firstly, you must program the DPC into TEST MODE (Plug-in oven
press [Timer/Clock] pad twice press [Start] pad once
press [Micro Power] pad once.)
2. Keep pressing [ [Timer/Clock] ] pad for more than 2 seconds until
buzzer beeps.
3. Press [Start] pad twice, oven will show error code.
NOTE:
1. If any error was observed, it will be kept in memory up to 3
errors in the past. If there are more than 4 cases, the memory will
renew the latest 3 errors codes.
2. Press [Start] pad again, one more older error code will be
displayed.
3. If the oven is ok, it will show “000” and blinking.
42
4. Error cod list
H** Hardware problem, oven itself has problem.
U** Usage problem such as run out of water and oven itself works well.
Usage problem
U14 No water during steam cooking (It is able to show up both
in test mode and cooking mode)
U40 No load operation, controlled by magnetron thermistor
U65 Power down controlled by Inverter thermistor
HOT Oven is hot (It is able to show up both in test mode and
cooking mode)
43
SYMPTOM CAUSE CORRECTIONS
1. Oven stops in 3 seconds No input AC is supplied to 1. Latch Switch
after pressing start pad. H.V.Inverter (U) CN702 terminals 2. Power relay RY1
3. Loose lead wire connector CN701,
CN702
Oven stops in 23 seconds H.V.Inverter (U) operates by the 1. Magnetron
after pressing start pad. control signals from DPC but 2. Loose lead wire connector CN703
magnetron is not oscillating
Oven stops in 1 minute Oven thermistor circuit is not 1. Oven thermistor
after pressing start pad. functions. 2. Loose wiring
(Convection/Grill
convection cooking)
Oven stops in 30 seconds Steam heater thermistor circuit is 1. Steam heater thermistor
after pressing start pad. not functions. 2. Loose wiring
(Steam cooking) 3. bad conductibility between thermistor
and steam heater
2. No display and no Most probably loose connection of 1. Align door, Door Latch Switches
operation at all. connectors, or door latch 2. Loose wiring connectors
Fuse is blown. mechanism is not adjusted properly
44
SYMPTOM CAUSE CORRECTIONS
1. Oven is dead. 1. Defective circuit breaker
Fuse is OK. 2. The switch of circuit breaker is in Turn the switch of circuit breaker
No display and no operation "O" position "I" position.
at all. 3. Open or loose lead wire harness
4. Open thermal cutout / thermistor Check fan motor if thermal
defective.
5. Open low voltage transformer
6. Defective DPC
2. No display and no operation 1. Shorted lead wire harness Check adjustment of primary,
at all. / Fuse is blown. Defective primary latch switch secondary latch switch and
2. (NOTE 1) switch including door.
3. Defective short switch (NOTE 1)
4. Defective Inverter Power Supply
(U)
NOTE 1:
All of these switches must be replaced at the same time.
Check continuity of power relay B (RY1)'s contacts (between 1
and if it has continuity, replace power relay B (RY1) also.
3. Oven does not accept key 1. Key input is not in proper sequence Refer to operation procedure.
input(Program)
2. Open or loose connection of
membrane key pad to DPC (Flat
cable)
3. Shorted or open membrane key
board
4. Defective DPC Refer to DPC troubleshooting.
4. Fan motor turns on when 1. Misadjustment or loose wiring of Adjust door and latch switches.
oven is plugged in with door secondary latch switch
closed. 2. Defective secondary latch switch
45
SYMPTOM CAUSE CORRECTIONS
5. Timer starts count down but 1. Off-alignment of latch switches Adjust door and latch switches.
no microwave oscillation. Open or loose connection of high
(No heat while oven lamp 2. voltage circuit especially
and fan motor turn on) magnetron filament circuit
NOTE:
Large contact resistance will
cause lower magnetron filament
voltage and cause magnetron to
have lower output and/or be
intermittent.
3. Defective high voltage component Check high voltage component
H.V. Inverter Power Supply (u) according to component test
Magnetron procedure and replace if it
defective.
4. Open or loose wiring of power
relay B (RY1)
5. Defective primary latch switch
6. Defective DPC or power relay B Refer to DPC troubleshooting
(RY1)
6. Oven can program but timer 1. Open or loose wiring of secondary
does not start countdown. latch switch
2. Off-alignment of secondary latch
switch
3. Defective secondary latch switch
7. Microwave output is low. 1. Decrease in power source voltage Consult electrician
Oven takes longer time to 2. Open or loose wiring of magnetron
cook food. filament circuit.(Intermittent
oscillation)
3. Aging change of magnetron
8. Fan motor turns on and 1. Shorted primary latch switch
turntable rotates when door
is opened.
9. Oven does not operate and 1. Defective DPC Check grounding connector
return to plugged in mode as escutcheon base.
soon as start pad is pressed.
10. Loud buzzing noise can be 1. Loose fan and fan motor
heard.
11. Heater does not turn on. 1. Open or loose wiring of heater
2. Defective heater
3. Defective power relay
4. Defective DPC
12. Oven stops operation during 1. Open or loose wiring of primary Adjust door and latch switches.
cooking. and secondary latch switch
2. Operation of thermal cutout
46
7.3. Troubleshooting of inverter circuit (U) and magnetron [NEW H.V.
]
This oven is programmed with a self diagnostics failure code system which will help for
troubleshooting. H95, H97, H98 and H99 are the provided failure codes to indicate magnetron and
inverter circuit problem areas. This section explains failure codes of H95, H97, H98 and H99.
First, you must program the DPC into TEST MODE, press [Timer/Clock] pad twice Press [
Start] pad once press [Micro Power] pad once. Program unit for operation. H95, H97, H98,
H99 appears in display window a short time after start key is pressed and there is no microwave
oscillation.
47
SYMPTOM STEP CHECK RESULT CAUSE/CORRECTION
No display when oven is first 1 Fuse pattern of D.P.C. Normal Step2
plugged in
Open Replace D.P.C.
Pattern
2 Low voltage transforment Abnormal 0V L.V.T.
(L.V.T.) secondary voltage Normal Step3
3 IC10 pin5 voltage Abnormal IC10
Normal=5V IC1, CX320, Display
No key input 1 Membrane switch continuity Abnormal Membrane switch
Normal IC1
No beep sound 1 IC1 pin 8 voltage Abnormal IC1
Normal=5V BZ210, Q210
Power relay A(RY2) does not 1 IC1 pin 22 voltage while Abnormal IC1
turn on even though the operation
program had been set and Normal=5V Step2
the start pad is tapped
2 IC220 pin13 voltage Abnormal IC220
Normal RY2
0.7V
No microwave oscillation at 1 IC1 pin 24 voltages while Abnormal IC1
any power operation at high power Normal=5V Step2
2 IC220 pin11 Abnormal IC220
Normal Step3
0.7V
3 Short circuit between collector Still not turn RY1
and emittes of Q227 on
RY1 turns on Q227, Q224,Q225,Q226
Dark or unclear display 1 Replace display and check Normal Display
operation
Abnormal IC1
Missing or lighting of 1 Replace IC1 and check operation Normal IC1
unnecessary segment Abnormal Display
H95/H97/H98 appears in 1 Unplug CN702 (2 pin) connector Abnormal=0V 1. Latch Switch
window and oven stops and measure voltage between 2. D.P.C. /Power
operation.Program High terminals Normal= Step2
power for 1 minute and 220~240V
conduct following test 2 Unplug CN701 (3 pin) connector Abnormal=0V D.P.C.
quickly, unless H95/H97/H98 and measure pin3 voltage Approx. AC Magnetron
appears and oven stops
3V
48
Set-up:
The unit under question is connected through the Ammeter as shown below.
Procedure:
Follow the matrix table below to identify the problem source.
Note:
Do not replace both Inverter board and Magnetron simultaneously
and automatically without going through this procedure.
49
7.7. H.V. Inverter main parts list
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
Q701 A691EM300GP IGBT 1
Q702 IGBT 1
50
8.2. PARTS LIST
NOTE:
51
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
1 F00066V00HP CAUTION LABEL 1 EXCEPT ZPE
1 F00066W10ZP CAUTION LABEL 1 ZPE
2 F10016Y40XPG BASE 1
3 F10087J60XP RUBBER FOOT 2
4 F10084T00AP RUBBER FOOT 1
5 F1008-1F90 RUBBER FOOT 1
6 F110D6Y40SXP CABINET BODY 1 EXCEPT HPE & QPQ
6 F110D6Y40SHP CABINET BODY 1 HPE
6 F110D6Y40SBP CABINET BODY 1 QPQ
7 F200A6Y40HP OVEN 1
9 2M261-M32JY MAGNETRON 1
52
39 F67637J70XP INVERTER BRACKET B 1
53
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
40 F630G6Y40XP HEATER 2 HPE,YTE,KTE,PTE,ZPE
40 F630G6Y40MP HEATER 2 YPQ,MPQ,QPQ
41 F630F6Y40HP HEATER 1 HPE,YTE,KTE,PTE,ZPE
41 F630F6Y40MP HEATER 1 YPQ,MPQ,QPQ
43 F611E6Y40HP HEATER (DU) 1 HPE,YTE,KTE,PTE,ZPE
43 F611E6Y40MP HEATER (DU) 1 YPQ,MPQ,QPQ
44 F61457J70XP THERMAL CUTOUT 2
45 F66266Y40XPG THERMAL CUTOUT BRACKET 1
48 F01506W50XP NO TOUCHING LABEL 1 EXCPTE HPE
48 F01508G60HP NO TOUCHING LABEL 1 HPE
49 F22377J70XPG LEFT HEATER PANEL 1
50 F22367J70XPG RIGHT HEATER PANEL 1
51 F300B7J70XP LEFT HINGE (U) 1
52 F300U7J70XP RIGHT HINGE (U) 1
53 F601L7J70XP IR SENSOR (U) 1
54 A6760-1E20 SWING MOTOR 1
55 F44966Y40XP NOZZLE A 1
56 F45137J70XP TIE-IN C 1
57 F92017J70XP COPPER PIPE 1
58 F46507J70XP TUBE C 1
59 F92047J70XP TUBE D 1
60 F03346Y40HP MENU LABEL 1 HPE,YPQ,YTE,MPQ
60 F03346Y40KT MENU LABEL 1 KTE,PTE
60 F03346Y40ZP MENU LABEL 1 ZPE
60 F03346Y40QP MENU LABEL 1 QPQ
61 F90717J70XP SUPPORTER 1
62 XTWFA4+12T SCREW 4 FOR MAGNETRON
63 XTWFA4+12D SCREW 4 FOR CABINET BODY
65 F202Q6Y40BP UPPER HEATER PANEL 1
66 F15676Y40XP DRIP PLATE 1
67 F22776Y40XP LOWER HEATER PANEL 1
68 F10596Y40BP BACK COVER 1
69 F10586Y40BP SIDE COVER 1
70 F10576Y40XP BACK COVER C 1
71 F40306Y40BP EXHAUST GUIDE D 1
72 F41706Y40BP HEATER MOUNTING PLATE 1
74 F22394V00BP CONVECTION FAN BLADE 1
75 F41594V00BP COOLING FAN BLADE 1
79 F41806Y40BP CONVECTION FAN BRACKET 1
80 F490S6Y40XP CONVECTION FAN MOTOR 1
81 F631D6Y40XP CONVECTION HEATER 1 HPE,YTE,KTE,PTE,ZPE
81 F631D6Y40BP CONVECTION HEATER 1 YPQ,MPQ,QPQ
82 F64174V00BP HEATER BRACKET A 1
83 F66796Y40BP CONVECTION INSIDE COVER A 1
85 F607J6Y40BP CONVECTION ASSEMBLY(BU) 1 (INCLUDING IN CONVECTION OUTSIDE COVER B &
ADIABATIC MATERIAL)
86 F67356Y40XP HEATER PROTECTOR 1
87 F02395E20KN CORD CAUTION LABEL 1 KTE,PTE
89 F40276Y40BP INVERTER AIR GUIDE 1
90 F50586Y40XP BRACKET 1
91 F50596Y40XP COVER 1
92 F60586Y40XP CIRCUIT BREAKER 1
93 F03586Y40XP CIRCUIT BREAKER HARNESS 1
94 F66286Y40BP THERMAL CUTOUT BRACKET 1
54
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
98 F15607J70ZP ALUMINUM PLATE 1 QPQ,ZPE
100 F01576Y40HP NAME PLATE 1 HPE
100 F01576Y40YP NAME PLATE 1 YPQ
100 F01576Y40YT NAME PLATE 1 YTE
100 F01576Y40MP NAME PLATE 1 MPQ
100 F01576Y40KT NAME PLATE 1 KTE
100 F01576Y40PT NAME PLATE 1 PTE
100 F01576Y40ZP NAME PLATE 1 ZPE
101 F00066W10MP CAUTION LABEL 1 YPQ
101 F00068H00YT CAUTION LABEL 1 YTE
102 F02846Y40YP NO. LABEL 1 YPQ
103 F11656Y40KT REINFORCE BRACKET E 1
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
T1 F060Q6Y40XP WATER TANK (U) 1 (INCLUDING TANK COVER & SEAL)
T2 F061A6Y40XP WATER TANK 1
T3 F06116Y40XP TANK COVER 1
T4 F44247J70XP SEAL 1
55
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
E1 F603L6Y40HP D.P.CIRCUIT (AU) 1 HPE
E1 F603L6Y40YP D.P.CIRCUIT (AU) 1 YPQ
E1 F603L6Y40YT D.P.CIRCUIT (AU) 1 YTE
E1 F603L6Y40MP D.P.CIRCUIT (AU) 1 MPQ
E1 F603L6Y40PT D.P.CIRCUIT (AU) 1 KTE,PTE
E2 F605S6Y40XP D.P.CIRCUIT (HU) 1
E3 F630Y6Y40SHP MEMBRANE SWITCH(U) 1 HPE,YPQ,YTE,MPQ
E3 F630Y6Y40SKT MEMBRANE SWITCH(U) 1 KTE,PTE
E4 F800A6Y40SHP ESCUTCHEON BASE (U) 1 HPE,YPQ,YTE,MPQ (INCLUDING MEMBRANE SWITCH(U))
E4 F800A6Y40SKT ESCUTCHEON BASE (U) 1 KTE,PTE (INCLUDING MEMBRANE SWITCH(U))
E5 F800B6Y40SXP ESCUTCHEON BASE (BU) 1
E6 F803G8J00SXP POP-UP DIAL (U) 2 HPE,YPQ,YTE,MPQ,KTE,PTE
E7 F80186Y40XP BRACKET 1 HPE,YPQ,YTE,MPQ,KTE,PTE
E8 F81246Y40XP BREAKWATER 1 HPE,YPQ,YTE,MPQ,KTE,PTE
E9 F80876Y40XP EARTH LEAD 1 HPE,YPQ,YTE,MPQ,KTE,PTE
E10 F400L6Y40XP PUMP-LED(U) 1 (INCLUDING PUMP & LED PCB)
E11 F83876Y40XP BUTTON 1 HPE,YPQ,YTE,MPQ,KTE,PTE
E12 F06397J70XP PUMP BRACKET 1
E13 F66166Y40BP FLAT CABLE 1 (WIDE ONE)
E14 F66166Y40XP FLAT CABLE 1 (NARROW ONE)
E15 F44266Y40BP SEAL B 1
E16 F46487J70XP TUBE A 1
E17 F46497J70XP TUBE B 1
E18 F45126Y40BP TIE-IN B 1
56
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
E21 F603L6Y40ZP D.P.CIRCUIT (AU) 1 ZPE
E21 F603L6Y40QP D.P.CIRCUIT (AU) 1 QPQ
E22 F605S6Y40XP D.P.CIRCUIT (HU) 1
E23 F630Y6Y40SQP MEMBRANE SWITCH(U) 1 QPQ
E23 F630Y6Y40SZP MEMBRANE SWITCH(U) 1 ZPE
E24 F800A6Y40SQP ESCUTCHEON BASE (U) 1 QPQ (INCLUDING MEMBRANE SWITCH(U))
E24 F800A6Y40SZP ESCUTCHEON BASE (U) 1 ZPE (INCLUDING MEMBRANE SWITCH(U))
E25 F800B6Y40SBP ESCUTCHEON BASE (BU) 1 QPQ,ZPE
E26 F803G6Y40SBP POP-UP DIAL (U) 2 QPQ,ZPE
E30 F400L6Y40XP PUMP-LED(U) 1 (INCLUDING PUMP & LED PCB)
E31 F83876Y40QP BUTTON 1 QPQ
E31 F83876Y40BP BUTTON 1 ZPE
E32 F06397J70XP PUMP BRACKET 1
E33 F66166Y40BP FLAT CABLE 1 (WIDE ONE)
E34 F66166Y40XP FLAT CABLE 1 (NARROW ONE)
E35 F44266Y40BP SEAL B 1
E36 F46487J70XP TUBE A 1
E37 F46497J70XP TUBE B 1
E38 F45126Y40BP TIE-IN B 1
E39 F80876Y40BP GROUNDING PANEL 1 QPQ,ZPE
E40 F01576Y40QP NAME PLATE 1 QPQ
57
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
D1 F390L6Y40SXP DOOR(U) 1 HPE,YPQ,YTE,MPQ,KTE,PTE (INCLUDING DOOR C & SEAL)
D2 F30856Y40XP DOOR C 1
D3 A3334-1K00 SEAL 1
D4 F30546Y40BP DOOR ARM (LEFT) 1
D5 F30446Y40BP DOOR ARM (RIGHT) 1
D6 F32316Y40XP DOOR KEY SPRING A 1
D7 F32307J70XP DOOR KEY SPRING B 1
D8 F302A6Y40SXP DOOR B (U) 1 HPE,YPQ,YTE,MPQ,KTE,PTE
58
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
W1 F030A6Y40XP LEAD WIRE HARNESS 1
W2 F030E7J70XP H.V.LEAD WIRE 1
59
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
P1 F00036Y40HP INSTRUCTION MANUAL 1 HPE,YPQ,YTE,MPQ
P1 F00036Y40KT INSTRUCTION MANUAL 1 KTE,PTE
P1 F00036Y40ZP INSTRUCTION MANUAL 1 ZPE
P1 F00036Y40QP INSTRUCTION MANUAL 1 QPQ
P2 F01026Y40KT PACKING CASE,PAPER 1 HPE,YPQ,YTE,MPQ,KTE,PTE
P2 F01026Y40ZP PACKING CASE,PAPER 1 ZPE
P2 F01026Y40QP PACKING CASE,PAPER 1 QPQ
P3 F01046Y40XP UPPER FILLER 1 HPE,YPQ,YTE,MPQ,KTE,PTE
P3 F01046Y40BP UPPER FILLER 1 QPQ,ZPE
P4 F01056Y40XP LOWER FILLER 1 HPE,YPQ,YTE,MPQ,KTE,PTE
P4 F01056Y40BP LOWER FILLER 1 QPQ,ZPE
P5 F01066Y40XP P.E BAG 1
P6 F01078100XN DOOR SHEET 1
P7 F06217J70XP QUADRATE COOKING TRAY 1
P8 F01126Y40XP FOAM 1
P9 F01136Y40XP FOAM 1
P10 F06027J70XP OVEN RACK 1
P11 F60037J70XP CERAMIC COVER 1
P12 F01126Y40BP FOAM 1
P13 F06037J70XP CRISPY PAN 1
P14 F000B6Y40HP COOKING GUIDE 1 HPE,YPQ,YTE,MPQ
P14 F000B6Y40KT COOKING GUIDE 1 KTE,PTE
P14 F000B6Y40ZP COOKING GUIDE 1 ZPE
P15 F01926Y40XP SHEET 1
P17 F01096Y40XP SHEET 1
P18 F01896Y40XP PROTECT CORNER 2
P19 F02246Y40KT NOTICE 1 EXCEPT QPQ
P19 F02246Y40BP NOTICE 1 QPQ
P23 F0731-1450 MITTEN 1
P26 F01567J70HP NOTICE 1 HPE,YPQ,YTE,MPQ
P27 F04456Y40MP OVERLAY 1 YPQ,MPQ
P28 F04456Y40YP OVERLAY 1 YPQ,MPQ
P29 F04456Y40KT OVERLAY 1 KTE,PTE
P30 F04456Y40PT OVERLAY 1 KTE,PTE
60
61
9.2. PARTS LIST
62
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
BZ210 L0DDEA000014 BUZZER 1 2.0KHz
C11 AECEWG1C471B AL CHEM CAPACITOR 1
470 F/16V
C12,C15 AECETS1C220B AL CHEM CAPACITOR 2
22 F/16V
C29 AECETK2W101B AL CHEM CAPACITOR 1
10 F/450V
C27 AESCT08F104M AL CHEM CAPACITOR 1
0.1 F/25V
C224 AECT81F102K CERAMIC CAPACITOR 1 1000PF/1000V
C26 ECKN3A222KBP CERAMIC CAPACITOR 1 2200PF/1000V
CN1 K1KA05A00308 CONNECTOR 1 5 pin
CN2 K1KA06A00246 CONNECTOR 1 6 pin
CN3 K1KA06A00246 CONNECTOR 1 6 pin
CN4 K1KA05A00236 CONNECTOR 1 5 Pin
CN5 K1MN27A00012 CONNECTOR 1
CN6 K1KA04A00327 CONNECTOR 1 4 pin
CN7 K1MN27B00032 CONNECTOR 1 27 pin
CN8 K1KA14A00201 CONNECTOR 1 14 pin
CN9 F03536Y40XP CONNECTOR 1 6 Pin
CN11,CN12 F03536Y40XP LEAD WIRE 2 5 pin
CN13 K1MN09B00054 LEAD WIRE 1 13 pin
CN14 K1MN05AA0019 LEAD WIRE 1 5 pin
CN15 K1MN09A00001 LEAD WIRE 1
PIN1,PIN2 K4CE01000003 PIN 2
CX320 H0D100500017 CRYSTAL RESONATOR 1 8.00MHz (YTE,QPQ,ZPE)
CX320 EFOEC1005T4 CERAMIC RESONATOR 1 8.00MHz (HPE,YPQ,MPQ,KTE,PTE)
D180-D191 B3ACB0000065 CHIP LED 12
D220 B0EAKT000025 DIODE 1
D221,D225-D227,D493 MA2C19600E DIODE 5
D10 AESB280TLRC DIODE 1
D25 D4EAY511A036 VARSITOR 1 510V
D28 B0EAKT000025 DIODE 1
D33 AEUF4006TLRC DIODE 1
D100 B0AACK000004 DIODE 1
DISP1 L5AAAFE00013 LCD 1 HPE,YPQ,YTE,MPQ,KTE,PTE
DISP1 L5AAAFE00014 LCD 1 QPQ,ZPE
DISPL1 HOLD F66176Y40XP LCD HOLDER 1 HPE,YPQ,YTE,MPQ,KTE,PTE
DISPL1 HOLD F66176Y40BP LCD HOLDER 1 QPQ,ZPE
E80936Y40BP DIFFUSION SHEET 1
IC1 MN101C57DDE L.S.I. 1 HPE,YPQ,YTE,MPQ
IC1 MN101C57DDJ L.S.I. 1 QPQ
IC1 MN101C57DDK L.S.I. 1 KTE,PTE,ZPE
IC10 C0DBAHD00013 IC 1
IC220,IC221 B1HBGFF00007 IC 2
IC350 C0EBH0000264 IC 1
IC26,IC100 B3PAA0000387 IC 2
IC28 MIP0255SPSCF IC 1
IC220 B3PAC0000060 IC (SSR) 2
Q492 B1BAAJ000003 TRANSISTOR 1
Q227 B1ACGF000004 AUDION 1
R10 D0AE470JA155 CARBON FILM RESISTOR 1 47 ,1/4W,5%
R210,R220,R221 D0AE391JA155 CARBON FILM RESISTOR 3 390 ,1/4W,5%
R240 D0AE751JA155 CARBON FILM RESISTOR 1 750 ,1/4W,5%
R231 D0AE102JA155 CARBON FILM RESISTOR 1 1K ,1/4W,5%
R13 D0AE222JA155 CARBON FILM RESISTOR 1 2.2K,1/4W,5%
63
R13 D0AE222JA155 CARBON FILM RESISTOR 1 2.2K,1/4W,5%
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
R211 D0AE512JA155 CARBON FILM RESISTOR 1 5.1K,1/4W,5%
R232 D0AE103JA155 CARBON FILM RESISTOR 1 10K,1/4W,5%
R100,R101 AERT15X393JT CARBON FILM RESISTOR 2 39K,1/2W,5%
R28 AERY16753KcE RESISTOR 1 75K,1/2W,5%
R11,R223 D0AE104JA155 CARBON FILM RESISTOR 2 100K,1/4W,5%
R27 AERY15J1RQbB RESISTOR 1 1 ,1/2W,5%
RY1,RY4,RY5,RY7,RY9 K6B1AGA00212 POWER RELAY 5
RY2,RY6 K6B1AGA00180 POWER RELAY 2
T10 ETS19AA2B1AC SWITCHING POWER 1
SUPPLY
ZD10 B0BA01100053 ZENER DIODE 1
SW1 EVQ11L05R SWITCH 1
RE81,RE82 EVEJ1HF2224B REVOLVING ENCODER 2
64