•C

 E MARKED SMOKE EXTRACT

•E
 N TESTED FIRE RATED
KITCHEN EXTRACT AND
PRESSURISATION
• I NSTALLED UNDER THIRD-
PARTY CERTIFIERS FIRAS

Airforce H&V Ltd., 47/48 Broomhill Close, Dublin 24, D24 KH64, Ireland.
Ph: +353 (0)1 4040 909  Email: [email protected]  www.fireduct.eu
 UNDERSTANDING THE
NEW EN REGULATIONS
SAFE4 is a fire rated ductwork , the result
of 10 years of research and development,
produced in an ISO9001 quality control
management environment, and installed
by certified installers. The old standard of
BS476 has been superseded as of July 2013
and has been replaced by the new European
Standard EN  12101-7 for smoke extract and
EN  15871 for fire ductwork, kitchen extract
and pressurisation.

SAFE4 have tested all products to the latest

EN standards and as required by law provide
CE marking on products where a harmonised
standard exists.

The tests vary for different types of duct:

EN 1366 PART 1 EN 1366 PART 8 EN 1366 PART 9

fire duct, kitchen multi compartment single compartment
extract & pressurisation smoke extract smoke extract

PERFORMANCE
CRITERIA
The test specifies the required components
measured under prescribed conditions or
periods of exposure to fire and includes
penetration seals, access doors, fixing
supports, unique insulation and sealant.

The system is tested as a whole and all

components of the system are tested to ensure
they all comply with the fire rating achieved
and ultimately the classification declared.

The limiting criteria by which the test results

are determined are insulation, integrity, smoke
leakage and cross sectional area.

The ASFP states that the inclusion of non

specific products, material and dimensional
modifications may result in the invalidity
Let us take you on the journey from BS to EN. of the final assembly, thus preventing
certification of works.

2  SAFE4  Understanding The New EN Regulations

Airforce H&V Ltd., 47/48 Broomhill Close, Dublin 24, D24 KH64, Ireland.
Ph: +353 (0)1 4040 909  Email: [email protected]  www.fireduct.eu
PENETRATION SEALS
Penetration seals are one of the areas of great
concern. They prevent fire spreading from one
compartment to another. Failure to achieve this
results in test termination.

SAFE4’s uniquely built penetration seals

withstand severe fire conditions and can
be easily installed from components locally
available.

SAFE4’s penetration seals are tested in

flexible walls, allowing them to be used in
stud partitions, block walls and concrete
floors.

The ASFP confirms that assemblies associated

with block work may not be suitable for
dry‑lining.

ACCESS DOORS
(SAFE DOOR)
Access doors tested are not standard access
doors, they are fire rated doors which must
withstand temperatures of up to 1000⁰c.
DW172 states that all interior surfaces of the
ductwork shall be accessible for cleaning and
inspection purposes. It is recommended that
access doors are installed every 3 meters.
These access doors must be the access doors
tested during Type A, Type B and Type C both
horizontally and vertically.

SAFE4 ducting is designed with specific

emphasis on strength with a minimum load
bearing rate per square meter because of
its uniquely built structure.

SAFE4’s EN range is unique in having one

of the lowest kg weight per square meter.

FIXING & SUPPORTS

Prescribed fixing and supports are an integral
part of the system and have been tested under
full fire conditions.

Understanding The New EN Regulations  SAFE4 3

www.airforcehv.com      Email: [email protected]      www.fireduct.eu
INSULATION
Fire rated insulation ensures that the
temperature measured (outside in Type A,
and inside in Type B) does not exceed 140⁰C
mean average above ambient during the test
and is deemed automatically failed if any
thermocouple rises to 180⁰C.

SAFE4 insulation is a compact calcium-

magnesium silicate blanket made from low
bio-persistence wool with a thickness of
38mm. It is totally inorganic and exonerated
from classification under Nota Q of EU
Directive 97/69/EC. It is a lightweight easy
to install insulation with an attractive finish
similar to the finish of standard thermal
insulation.
This scrim provides additional handling
It has a resistance to both thermal shock strength in addition to providing protection
and mould growth (anti-microbial), and against moisture absorption. SAFE4
can be used in hospitals because it has insulation has exceptional insulation
the required encapsulated insulation to properties withstanding temperatures of
ensure there are no migration of fibres. The 1200⁰c. At a typical ambient temperature
encapsulation is an aluminium foil / glass of 25⁰c the thermal conductivity would be
fibre reinforced aluminised polyester scrim. 0.044 W/mK.

INTEGRITY
The integrity of the entire system is based
on the performance of all elements from
penetration seals, to smoke leakage to cross
sectional area.

When all of the components perform to the

required standard, only then can the integrity
be classified.

SAFE4 achieved exceptional results in all

areas and therefore have a level of integrity
others can only hope to achieve.

SAFE4 achieved a benchmark result for

the type of steel ductwork tested which
was noted in the independent accredited
Warrington Exova test laboratory as not
having been achieved before.

4  SAFE4  Understanding The New EN Regulations

Airforce H&V Ltd., 47/48 Broomhill Close, Dublin 24, D24 KH64, Ireland.
Ph: +353 (0)1 4040 909  Email: [email protected]  www.fireduct.eu
TEST TYPE A Compartment Adjacent Compartment
with Fire Outbreak
T1 Temperature Sensor
Type A testing involves fire outside
the duct. The test furnace is raised to
Duct resists penetration
operating temperatures of 1000⁰c of fire from outside
with the specimen suspended Ventilation or Smoke Extract Opening
within. The duct passes through
the dedicated penetration seal
where various measurements and Type A Duct (fire outside) No fire penetration or transfer
observations are used to determine
its suitability and performance.
In this test no fire passes through the duct. up to 80 thermocouples inside the ducting.
The duct is tested for leakage, integrity and This determines the kitchen extract insulation
the rise in temperature where the duct is value.
insulated. The temperature is measured by

TEST TYPE B Adjacent Compartment

Compartment with fire outbreak
T2 Temperature Sensor
Type B involves fire inside the duct.
There is an opening in the duct
Duct resists penetration
within the furnace which allows of fire from inside
the fire to pass through the duct Ventilation or Smoke Extract Opening
unimpeded.
A fan connected to the duct Fire penetrates into duct through
Type B Duct (fire inside)
extracts hot furnace gas at a ventilator or smoke extract opening
velocity of 3 m/s at up to 500pa
negative pressure exposing the
is insulated. For this Type B test up to 80
internal skin to the full fire conditions.
thermocouples are mounted outside the
The duct is tested for leakage, integrity furnace determining the smoke insulation
and the rise in temperature where the duct value.

TEST TYPE C
Type C is carried out on smoke extract only.
It can only be tested once Type B has been
completed at a pressure of 500pa. The
insulation value achieved in Type B is the one
that is used for this classification.

The cross sectional area is measured uniquely

in the Type C test when it is placed under full
fire conditions and under pressure of 300pa.

Understanding The New EN Regulations  SAFE4 5

www.airforcehv.com      Email: [email protected]      www.fireduct.eu
LEAKAGE
Leakage is set to different parameters for
smoke extract and fire rated duct. Smoke
extract is tested to a maximum of 10m3/hr/m2
and a low of 5m3/hr/m2. Fire duct is tested at a
higher rate to a maximum of 15m3/hr/m2 and a
low of less than 10m3/hr/m2.

SAFE4 received a classification of

“S” in both tests, “S” being the highest
classification in this category.

CROSS SECTIONAL
AREA
Cross sectional area is the mechanical stability
of the duct being tested. Failure occurs when
the duct has a deflection and the cross sectional
area is reduced by more than 10%. This is
when the duct weakens as a result of full fire
conditions and negative pressure causing the
duct to convex. The duct becomes redundant
when it changes shape sufficiently impairing its
functionality and it loses the ability to perform.

Previously under BS the cross sectional area was

far more generous than the new stringent EN
standards. This is because the new EN standard
has identified this as a critical requirement
to maintain 90% of the cross sectional area
throughout the duration of the test.

SAFE4 meets and exceeds this

requirement with an exceptional level of
integrity.

TEST PRESSURE
Test pressure is typically carried out at a
minimum of 300pa for fire duct and 500pa
for smoke extract. During testing there is an
option to increase the pressure to a maximum
of 1500 pascals.

SAFE4 has tested all ducts to the

maximum pressure of 1500pa.

6  SAFE4  Understanding The New EN Regulations

Airforce H&V Ltd., 47/48 Broomhill Close, Dublin 24, D24 KH64, Ireland.
Ph: +353 (0)1 4040 909  Email: [email protected]  www.fireduct.eu
HORIZONTAL
& VERTICAL
All of the tests should be carried out both
horizontally and vertically. It is imperative
that the testing has been completed in both
as all real installations involve an element of
horizontal and vertical applications.

If only one application is tested, only that tested

application can be certified. For example if you
test Type A, B & C horizontally, you can only
certify horizontal applications and any duct
installed vertically cannot be certified.

CLASSIFICATION
The classification shall indicate if the
performance criteria are satisfied by fire from Classification symbols used:
inside or fire from outside or both and whether
E Integrity
it applies to vertical or horizontal orientations
or both. I Insulation
For example a classification of EI 30 (veho
S Smoke leakage
i<>o) indicates a ventilation duct capable of
satisfying 30 minutes integrity and insulation t class in time
from both inside to outside and vice versa in
both vertical and horizontal applications. Ve Vertical Duct

It is important to note that “t” class in time Ho Horizontal Duct

differs for smoke extract, fire rated ductwork
i fire inside the test (Type B or C)
and kitchen extract.

Smoke Extract o fire outside the test (Type A)

30, 60, 90 and 120 minutes i>o tested for fire inside duct
Fire rated/Kitchen Extract i<o tested for fire outside the duct
EI  15, 20, 30, 45, 60, 90, 120, and 240
i<>o tested for both respectively
E (uninsulated duct)  30, 60

The classification awarded is based on your

performance as a whole and categorised into
The classification is based on the first fail of
the nearest time bracket, always rounding
the test. For example, if the test achieves
down.
an insulation value of 120 minutes but
For example, if the test achieved a result of 88 the penetration seal fails at 70 minutes, a
minutes, the awarded classification would be classification of 60 minutes is awarded. The
60 minutes, because the result falls short of awarded classification is based on the weakest
the next classification of 90 minutes. element of the test.

Understanding The New EN Regulations  SAFE4 7

www.airforcehv.com      Email: [email protected]      www.fireduct.eu
THIRD PARTY
CERTIFICATION

It is important to ensure that fire resistant

duct installers are third party accredited by
a recognised UKAS accredited independent
third party certification scheme like FIRAS,
that ensures that the performance quality,
reliability and traceability of the fire duct is
achieved (DW144).

The use of independent certification schemes

such as FIRAS provides clients and specifiers of compliance with the Regulatory Reform
with confidence regarding the competence of Order and national equivalents (Technical
potential contractors. It helps them to fulfil their Guidance Document 18: Code of practise for
own duty of care under the CDM regulations the installation & inspection of fire resisting
and it gives the responsible person confidence ductwork).

The ASFP (Association for Specialist Fire

Protection) strongly promotes the use of
specialist third party certificated installers
and consequently requires all ASFP installer/
contractor members to hold third party
certification.

The use of non-specialist installers is not

recommended because they cannot provide
the same level of competency as distinct
from using a specialist third party certificated
installer.

8  SAFE4  Understanding The New EN Regulations

Airforce H&V Ltd., 47/48 Broomhill Close, Dublin 24, D24 KH64, Ireland.
Ph: +353 (0)1 4040 909  Email: [email protected]  www.fireduct.eu
CE MARKING OF THE CE marking ensures that the fire duct
manufacturer has tested all products to the
FIRE RATED DUCT present relevant BS  EN tests 1366-1, 1366-8
and 1366-9 at a notified certification body.
CE marking of products with
There is a requirement for the fire duct
harmonised (hEN) standards
manufacturer to have a quality management
became mandatory on the 1st of
system (ISO 9001), and also having passed
July 2013 as stated within the requirements of
a FPC (factory production control) for the
the European directive. Consequently smoke
manufacturing and to have third party
extract duct covered by product standard
certification for the installation of fire duct
BS EN 12101-7 must be CE marked (DW144).
systems.
The old standard BS476 cannot support CE
marking of construction products and has
been withdrawn where a harmonised standard
exists.

Fire resistant ductwork, kitchen extract and

pressurisation covered by product standard
EN  15871 will require mandatory CE marking
one year after the publication of the standard
is qualified in the Official Journal of the EU.
This will be harmonised shortly, however
under Irish law IS  EN  1366-1 became statute
in April 2015.

Understanding The New EN Regulations  SAFE4 9

www.airforcehv.com      Email: [email protected]      www.fireduct.eu
SPECIFICATION

SMOKE EXTRACT
All smoke extract ductwork will be to (hEN)
standard 12101-7 and tested to EN 1366-8 for
multi compartment or EN 1366-9 for single
See through the new EN regulations.
compartment.

Where multi compartment ductwork is for testing outside (A), inside (B) and smoke
required it must be insulated to the same extract (C) in both a horizontal and vertical
period of time as the compartment through position.
which it passes as required in DW172.
All ductwork rated “S” for smoke leakage and
All smoke extract will carry CE Marking from have been tested to high pressure 1500 PA. All
July 2013 and is to be installed under a third smoke extract will be tested in a flexible wall
party certifier such as Firas as identified in and be suitable for installation in stud partition,
DW144. All ductwork must have classification block wall and concrete floor.

KITCHEN EXTRACT
All Kitchen Extract will be to the EN standard
15871 and tested to EN 1366-1, and must be
insulated to the same period of time as the
compartment through which it passes as
required in DW172.

All kitchen extract ducting must be accessible

for cleaning and inspection purpose and
have a cleaning door (to the same fire rating)
installed every 3 meters as stated in DW172. SAFE4… it won’t set your world on fire.

All ductwork must have classification for testing

outside (A) and inside (B) in both a horizontal All kitchen extract ductwork will be tested in a
and vertical position. All ductwork rated “S” for flexible wall and be suitable for installation in
low leakage. stud partition, block wall and concrete floor.

10  SAFE4  Understanding The New EN Regulations

Airforce H&V Ltd., 47/48 Broomhill Close, Dublin 24, D24 KH64, Ireland.
Ph: +353 (0)1 4040 909  Email: [email protected]  www.fireduct.eu
FIRE RATED
DUCTWORK
All fire rated and pressurisation ductwork will
be to EN standard 15871 and tested to EN 1366‑1
vertically and horizontally for Type A (fire
outside) and Type B (fire inside).

All ductwork rated “S” for low leakage. All fire

rated ductwork will be tested in a flexible wall
and be suitable for installation in stud partition,
block wall and concrete floor.

AIRFORCE H&V
Airforce H&V is primarily a sales company. That
means we must be responsive, we must be
versatile, we must be keen to do business, and
most importantly we must be able to offer you
that much more than our rivals.

How do we achieve this? Quite simply by caring

enough, by tirelessly working on every project,
every order no matter how big or small, to
achieve just one end, a satisfied customer. And or our vast range of CE marked ventilation
not just satisfied, but happy and willing to do products, or even our competitiveness in fire
it all again with us, knowing that you are in rated ductwork installations. Instead we would
safe hands. Every great business is founded rather you satisfied yourself by examining
upon this premise, the ability to secure repeat our records, our track history, even our
business. accreditations.

We believe we are very good at what we do, we Most of all, we would like you to try us out
would like to think the very best, but then, who for yourself, and experience first-hand the
wouldn’t say that! Sure, we could go on to boast difference that we believe we bring, that will
about our quality standards in manufacturing, make you a customer of ours for life.

Understanding The New EN Regulations  SAFE4 11

www.airforcehv.com      Email: [email protected]      www.fireduct.eu
 Must Cal
l
Airforce
H& V!

Airforce H&V Ltd., United Kingdom

47/48 Broomhill Close, Dublin 24, 3rd Floor, The Pinnacle, Centre Court,
D24 KH64, Ireland. Station Way, Crawley, West Sussex, RH10 1JH.
Ph: +353 (0)1 4040 909 Ph: +44 (0)1 2937 63003
Email: [email protected] www.fireduct.eu