Manual Plancha PDF

Download as pdf or txt
Download as pdf or txt
You are on page 1of 20

STANLEY

HS6000
MOUNTED
HYDRAULIC COMPACTOR

Safety, Operati n and Maintenance


US 'S M U L

© 2010 Stanley Black & Decker, Inc.


New Britain, CT 06053
U.S.A.
65765 1/2014 Ver 6
TABLE OF CONTENTS
CERTIFICATE OF CONFORMITY............................................................................................................................. 4
SAFETY SYMBOLS.................................................................................................................................................... 5
SAFETY PRECAUTIONS........................................................................................................................................... 6
TOOL STICKERS & TAGS......................................................................................................................................... 7
OPERATION............................................................................................................................................................... 8
PREOPERATION PROCEDURES........................................................................................................................ 8
DAILY MAINTENANCE CHECKS ......................................................................................................................... 8
PRE-INSTALLATION INSTRUCTIONS................................................................................................................. 8
LOW-TEMPERATURE WARM-UP PROCEDURE................................................................................................ 8
GENERAL INSTRUCTIONS.................................................................................................................................. 9
COMPACTION....................................................................................................................................................... 9
GENERAL.............................................................................................................................................................. 9
SLOPE TECHNIQUE............................................................................................................................................. 9
SOIL TESTING...................................................................................................................................................... 9
DRIVING.............................................................................................................................................................. 10
TROUBLESHOOTING...............................................................................................................................................11
FLOW TEST PROCEDURES................................................................................................................................... 12
DEFINITION OF TERMS.......................................................................................................................................... 14
SPECIFICATIONS.................................................................................................................................................... 15
TORQUE TABLE...................................................................................................................................................... 15
HS6008F PARTS ILLUSTRATION........................................................................................................................... 16
HS6008F PARTS LIST............................................................................................................................................. 17
HS6019F, HS6026, HS6027 & HS6100 PARTS ILLUSTRATION............................................................................ 18
HS6019F, HS6026, HS6027 & HS6100 PARTS LIST.............................................................................................. 19

IMPORTANT

To fill out a Product Warranty Recording form, and for information on your warranty,
visit Stanleyhydraulic.com and select the Warranty tab.
(NOTE: The warranty recording form must be submitted to validate the warranty).

SERVICING THE STANLEY HYDRAULIC compactor. This manual contains safety, operation, and routine
maintenance instructions. Stanley Hydraulic Tools recommends that servicing of hydraulic tools, other
than routine maintenance, must be performed by an authorized and certified dealer. Please read the fol-
lowing warning.

WARNING
SERIOUS INJURY OR DEATH COULD RESULT FROM THE IM-
PROPER REPAIR OR SERVICE OF THIS TOOL.

REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE


DONE BY AN AUTHORIZED AND CERTIFIED DEALER.

For the nearest authorized and certified dealer, call Stanley Hydraulic Tools at the number listed on the
back of this manual and ask for a Customer Service Representative.

3
DECLARATION OF CONFORMITY
DECLARATION OF CONFORMITY
ÜBEREINSTIMMUNGS-ERKLARUNG
DECLARATION DE CONFORMITE CEE
DECLARACION DE CONFORMIDAD
Hydraulic Tools
DICHIARAZIONE DI CONFORMITA
______________________________________________________________________
I, the undersigned:
Ich, der Unterzeichnende:
Weisbeck, Andy
Je soussigné: Surname and First names/Familiennname und Vornamen/Nom et prénom/Nombre y apellido/Cognome e nome
El abajo firmante:
lo sottoscritto:

hereby declare that the equipment specified hereunder:


bestätige hiermit, daß erklaren Produkt genannten Werk oder Gerät:
déclare que l’équipement visé ci-dessous:
Por la presente declaro que el equipo se especifica a continuación:
Dichiaro che le apparecchiature specificate di seguito:

1. Category: Hydraulic Powered Compaction Machine


Kategorie:
Catégorie:
Categoria:
Categoria:

2. Make/Marke/Marque/Marca/Marca Stanley
3. Type/Typ/Type/Tipo/Tipo: HS3000, HS6000, HS8000, HS11000, HS22000
4. Serial number of equipment:
Seriennummer des Geräts:
Numéro de série de l’équipement:
Numero de serie del equipo:
All
Matricola dell´attrezzatura:

5. Mass/Masse/Masse/Masa/Massa 168/998 kg

Has been manufactured in conformity with


Wurde hergestellt in Übereinstimmung mit
Est fabriqué conformément
Ha sido fabricado de acuerdo con
E’ stata costruita in conformitá con

Directive/Standards No. Approved body


Richtlinie/Standards Nr Prüfung durch
Directives/Normes Numéro Organisme agréé
Directriz/Los Normas No Aprobado
Direttiva/Norme n. Collaudato

EN ISO 12100-1:2009 Self


EN ISO 12100-2:2009
Machinery Directive 2006/42/EC:2006

6. Special Provisions: None


Spezielle Bestimmungen:
Dispositions particulières:
Provisiones especiales:
Disposizioni speciali:

8. Representative in the Union: Patrick Vervier, Stanley Dubuis 17-19, rue Jules Berthonneau-BP 3406 41034 Blois Cedex, France.
Vertreter in der Union/Représentant dans l’union/Representante en la Union/Rappresentante presso l’Unione

Done at/Ort/Fait à/Dado en/Fatto a Stanley Hydraulic Tools, Milwaukie, Oregon USA Date/Datum/le/Fecha/Data 1-6-11

Signature/Unterschrift/Signature/Firma/Firma

Position/Position/Fonction/Cargo/Posizione Engineering Manager

4
1/6/2011
SAFETY SYMBOLS
Safety symbols and signal words, as shown below, are used to emphasize all operator, maintenance and repair ac-
tions which, if not strictly followed, could result in a life-threatening situation, bodily injury or damage to equipment.

This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that follow this symbol to avoid possible
injury or death.
This safety alert and signal word indicate an imminently hazardous situation
DANGER which, if not avoided, will result in death or serious injury.

This safety alert and signal word indicate a potentially hazardous situation
WARNING which, if not avoided, could result in death or serious injury.

This safety alert and signal word indicate a potentially hazardous situation
CAUTION which, if not avoided, could result in death or serious injury.

This signal word indicates a potentially hazardous situation which, if not avoid-
CAUTION ed, may result in property damage.

This signal word indicates a situation which, if not avoided, will result in damage
NOTICE to the equipment.

This signal word indicates a situation which, if not avoided, may result in dam-
IMPORTANT age to the equipment.

Always observe safety symbols. They are included for your safety and for the protection of the tool.

LOCAL SAFETY REGULATIONS


Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte-
nance personnel.

5
SAFETY PRECAUTIONS
Tool operators and maintenance personnel must always comply with the safety precau-
tions given in this manual and on the stickers and tags attached to the tool and hose.
A These safety precautions are given for your safety. Review them carefully before operat-
To .ivoio , .. riou , Injury Or' cle~th
ing the tool and before performing general maintenance or repairs.

Supervising personnel should develop additional precautions relating to the specific work
area and local safety regulations. If so, place the added precautions in the space pro-
vided in this manual.

The HS6008/6019 Mounted Hydraulic Compactor’s will provide safe and dependable
\'(-',ii I yr'
f-:· .ul t hr .mu.rl
~)r(11 i'l t I on
service if operated in accordance with the instructions given in this manual. Read and
understand this manual and any stickers and tags attached to the tool and hoses before
operation. Failure to do so could result in personal injury or equipment damage.

Check the rule and regulations at your location. The rules might include an employer's
;J r U '.l ~ t Io r I work safety program. Regulations may identify hazards such as working around utility
supply lines or hazardous slopes.

BE THOROUGHLY TRAINED BEFORE OPERATING THE UNIT ALONE


• Operator training must start in an area without bystanders and use all the controls until he/she can control the machine
fully under the conditions of the work area.

• When learning to operate a machine, do so at a slow pace.

KNOW THE WORK CONDITIONS


• The operator must know any prohibited uses or work areas for the machine. For example, excessive slopes and poor
or dangerous terrain conditions must be avoided.

OBEY SAFETY RULES


• Replace all faulty or leaking hydraulic hoses or fittings before further operation.

• Always operate the compactor with backhoe outriggers firmly on the surface. The compactor weighs more than the
bucket. Position the compactor with caution.

• Travel with the compactor in full tuck (transport) position only.

• Never operate with any person near the compactor or between the compactor and operator.

• Operate the compactor in properly shored trenches and excavations. Do not allow personnel to work in the excavation
near compactor operation.
• Make sure all controls (levers and pedals) are in the NEUTRAL position before starting the carrier.

• Wear safety eye protection, hard hat, and safety foot protection while operating the compactor.

• Operate the carrier or compactor from the operator's seat ONLY. Make sure the seat belt is securely fastened before
activating any controls.

• Make certain that no other personnel are within the arc prescribed by the movement of the stabilizers, front bucket or
backhoe boom.

• Keep hands and feet on the controls at all times when the machine is running.

• Before leaving the operator's seat, always lower the loader arms and the backhoe boom.
• NEVER leave the machine with the engine running. ALWAYS ENGAGE THE PARKING BRAKE.

• Stop the engine before attempting to make any repairs or adjustments to either the carrier or compactor.

• To avoid personal injury or equipment damage, all tool repair, maintenance and service must only be performed by
authorized and properly trained personnel.

6
TOOL STICKERS & TAGS

&WA N

29610 29609
CE Spec Plate CE Spec Plate
47351 (HS6008 Only) (HS6019 Only)
Composit Warning

HS6000
372083
Model Decal

47352 19276 09163


Lift Point Decal GPM Decal Stanley Logo Decal

7
OPERATION
Be sure the fluid and filter in the hydraulic system are
PREOPERATION PROCEDURES clean.

When tightening pipe threads, be careful that any seal-


DAILY MAINTENANCE CHECKS
ant used (Teflon ® tape, etc.) does not enter the hydraulic
system. Foreign matter introduced into the system may
Check for loose or missing fasteners. Tighten or replace as
damage hydraulic valves, motors and pumps.
needed. Refer to Torque Specifications in the Specification
section of this manual.
Follow instructions to install the Stanley priority valve in the
carrier hydraulic system. the warranty is in effect only if the
Check to be certain that the flow control valve on the carrier
valve and compactor are installed as outlined in the valve
is set to the proper flow for the compactor. Refer to the
kit installation instructions. Major modifications or equip-
Specification section of this manual.
ment substitution will cause the warranty to be void unless
prior engineering approval has been granted by Stanley
Check shock mounts for cracks or tears. Rotate shock
Hydraulic Tools.
mounts 180° when fatigue tears begin to show at top outer
crease of the shock mount. This will prolong the life of the
The Stanley priority valve is a metering (to the hydraulic
shock mount.
tool) pressure compensating valve that controls the flow to
the attachment and gives the primary system (i.e. backhoe
Check for abrasion and hydraulic leaks at fittings and
functions) full operating pressure. Diverter valves or simple
hoses. Replace defective hoses and fittings. Adjust hoses
flow control valves will not perform all of these required
and tighten fittings so the hoses do not deflect into contact
functions.
with structure during use.
Note:
On carriers where priority valves are not used, check
WARNING with your local Stanley distributor for an adapter kit to
equip your carrier for a specific model of compactor.
DO NOT USE BARE HANDS TO CHECK OR
SEARCH FOR HYDRAULIC LEAKS AROUND
HOSES AND FITTINGS. PINHOLE LEAKS CAN LOW-TEMPERATURE WARM-UP PROCEDURE
PENETRATE THE SKIN. TO INSPECT FOR
LEAKS, DEPRESSURIZE THE SYSTEM, CLEAN When the weather gets cold, the shock mounts on com-
AROUND SUSPECTED AREA, REPRESSURIZE pactors can become stiff. In severe weather, where the
THE SYSTEM, AND VISUALLY CHECK FOR ambient temperature is below freezing for extended peri-
ods, shock mounts can even become brittle. Therefore, it
LEAKS.
is necessary to warm the shock mounts prior to using the
compactor. To warm the shock mounts follow these steps:
Lubricate bearings with two pumps of grease every 40
hours of operation. A greasing location is provided in both
1. After starting the carrier, warm up the system until hy-
bearing carriers.
draulic lines are warm to the touch.
Inspect pins and bushings for correct fit and lubrication.
2. With the carrier at idle, place the compactor flat on the
ground, and using a slight down pressure to keep the com-
Check level of hydraulic reservoir on carrier.
pactor in place, turn the compactor on. DO NOT place a
load on the compactor during this procedure.
Make certain that quick couplers are fully engaged and leak
free.
3. When the ambient temperature is below freezing, the
compactor should be operated on the ground with a slight
PRE-INSTALLATION INSTRUCTIONS down pressure (no load) for at least one minute before put-
ting it to work.

Test the carrier hydraulic system to verify that the system


is operating at the manufacturer's specified capacity and
pressure ratings.

8
OPERATION
With a standard baseplate, the compactor is held with
full down pressure for no more than 5-10 seconds. The
IMPORTANT application pattern should always begin next to a bank or
DO NOT SUSPEND THE COMPACTOR IN THE AIR DURING footing and at the previously compacted area. When the
THE WARM-UP PROCEDURE. maximum attainable density for that particular soil condition
is reached, a slight increase in vibration will be felt by the
THE COMPACTOR MUST BE PLACED FLAT ON THE operator. This increase in vibration is in no way harmful to
GROUND WITH A VERY SLIGHT DOWN PRESSURE TO the tractor, and indicates that the soil will not compress any
KEEP IT IN PLACE. WHEN AMBIENT TEMPERATURES
ARE BELOW FREEZING, SUSPENDING THE COMPACTOR further. In fact, additional time in that location may actually
IN THE AIR WITHOUT FIRST WARMING IT UP MAY CAUSE loosen the soil previously compacted.
THE SHOCK MOUNTS TO CRACK.
Work as much area as possible from one position and
FAILURE TO FOLLOW THESE PROCEDURES WILL VOID overlap each compacted section slightly. The vibration
COMPACTOR SHOCK MOUNT WARRANTY.
frequency has been chosen to give maximum efficiency in
granular soils using lifts of 2 to 4 feet. The closer the width
of the trench is to the width of the compactor, the higher the
GENERAL INSTRUCTIONS delivered compactive effort.

The compactor is a device that uses available force to It is necessary to turn the compactor OFF when being
the best advantage. The DYNAMIC FORCE of the mass transported or sitting idle. Should the running compactor
weight assembly, turning at a high rpm, produces a vibra- be placed on a hard surface without down pressure, the
tory force, and with controlled placement, an impact force. unit and the carrier will vibrate excessively. Down pressure
The DOWN PRESSURE of the carrier on the compactor transmits the vibration to the soil; neutral pressure will rattle
gives a high static pressure which assists in the compac- the whole carrier assembly.
tion or driving. The vibration frequency is controlled by the
hydraulic flow input to the compactor and is optimized for SLOPE TECHNIQUE
use in granular soils. The rate and density of compaction
depends on such factors as moisture content of the soil, This method of compaction is of primary interest to a
condition of the compactor and carrier, and the skill of the pipeline contractor seeking high production and efficient
operator. equipment utilization. The fill material is placed at one end
of the trench and allowed to seek its own angle of repose.
Compaction is begun on this angle above, but still near, the
NOTICE top of the pipe. All fill material is backfilled to this angle and
Efficient compactor performance is directly related to the the compactor is worked up and down the slope. Backfill-
flow rate specified. A higher flow rate does not improve ing, compaction, and resurfacing can be done very shortly
performance. It results in fluid overheating, and contributes after the pipe is in place.
to early bearing failure. A lower flow rate causes reduced
compaction performance. SOIL TESTING

Compaction density specifications are based on soil sam-


The rate of compaction to a 95% Modified Proctor in
ples of a set moisture content and soil composition. Chang-
granular soils is approximately 25 cubic yards per hour for
ing weather conditions, for example, can alter the moisture
the HS6000. This figure is variable and depends on such
content of the fill being used, and may make meeting the
factors as moisture content of the soil, condition of the com-
specifications impossible. It is imperative that frequent and
pactor and carrier and the skill of the operator.
reliable tests be conducted during application of the com-
pactor to determine the maximum lift that can be used and
COMPACTION still provide the required density. It is important that lifts in
excess of the established test results NOT be used if the
GENERAL required density is to be achieved and maintained.

The following instructions are very important to the proper


performance of the compactor and the attainment of the
specified compaction density.

9
OPERATION

DRIVING One note of caution; the forces generated and the meth-
ods used while driving with a vibratory device preclude the
Many driving jobs can be done with the compactor. Timber calculation of "bearing loads" for a piling or sheet of mate-
sheeting, steel and aluminum sheeting, H and I-beams, rial. DO NOT USE THE COMPACTOR IN APPLICATIONS
soldier piles and guard rail posts. The compactor will drive WHERE A BEARING LOAD IS SPECIFIED.
these materials in most soil conditions, except solid rock or
soil with a very high clay content.

The compactor is placed on the object to be driven using


the front one-third (that portion of the baseplate furthest
from the operator) of the baseplate. This position is critical
to proper delivery of the compactor's vibratory force into the
object. The front portion of the compactor will impart an
impact or "slap" that will drive the material into the soil. The
center portion of the compactor will "rock" on the material
and provide very little impact force.

Apply down pressure evenly, but do not compress the


shock mounts fully. Too much down pressure will make
the compactor difficult to control on top of the driven object,
and the impact required will be damped out.

WARNING
SERIOUS INJURY OR DEATH COULD RESULT FROM ATTEMPT-
ING TO SUPPORT THE DRIVEN MATERIAL.

PERSONNEL WHO ATTEMPT TO SUPPORT THE DRIVEN MATE-


RIAL CAN BE STRUCK OR CRUSHED.

DO NOT ATTEMPT TO SUPPORT THE DRIVEN MATERIAL.

10
TROUBLESHOOTING
If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem.

PROBLEM CAUSE SOLUTION


Compactor Inoperative. System Flow Valve not operating or Adjust flow for compactor; flow and
adjusted incorrectly. pressure test attachment circuit or
compactor flow control, if installed.
Seized bearings. Replace bearings and perform flow
and pressure tests.

Kinked hose. Replace.


Plugged quick-disconnect Repair or replace.
Rapid bearing failure. Lack of lubrication. Lubricate both bearings every 40
hours.
Overspeeding. Adjust flow for compactor; flow and
pressure test attachment circuit or
compactor flow control, if installed.
Rapid shock mount failure. Excessive down pressure or carrier Compress shock mounts no more than
too large for compactor. 2-2.5 in./51-64 mm during operation.
Cold weather operation. Warm up according to Low-Tempera-
ture Warmup procedure.
Failure to achieve required compac- Improper use. See Operation section of this manual.
tion specifications.
Overspeeding or underspeeding of Adjust flow for compactor; flow and
compactor. pressure test attachment circuit or
compactor flow control, if installed.
Moisture/soil content incorrect for Correct condition of soil, or compactor
specified density.. specifications are not reasonable for
conditions.

11
FLOW TEST PROCEDURES
The correct performance of this procedure will verify if the NOTE:
auxiliary circuit of the carrier is adequate to properly oper- The relief valve pressure must be greater than the op-
ate a Stanley attachment. erating pressure of the attachment and three times the
back-pressure. Never use the relief valve to control the
This procedure is generic in form. It is the end users re- flow rate in the circuit. Cracking pressure means the
sponsibility to ensure that this procedure will work with his loss of 4 or more GPM.
specific type of equipment.
Record the relief cracking pressure _____ psi.
If an adequate flow meter is not available contact your
Stanley Hydraulic Distributor for assistance. Example:
Operation pressure of a breaker is 2700 psi. Back-pres-
sure is 150 psi. A good rule to follow when setting the relief,
TEST PROCEDURE
multiply the back pressure by 3 then add this number to the
operation pressure of the attachment.
1. With the auxiliary circuit (or kit) completely installed con-
nect the flow meter between the tool inlet and outlet hoses.
Operating Pressure 2700 psi
Back-pressure 450 psi
NOTE:
Operating pressure of the tool 3150 psi
Always use the hoses that are supplied for the at-
tachment and make sure the machine hydraulic oil is
The relief valve setting must be greater than the estimated
between 90° to 120° F. This will assure correct readings
operating pressure of the tool. If the setting is lower, dam-
and adjustments.
age to the circuit may occur. Excess heat will be generated
in the circuit which will damage the attachment and carrier.
2. With the machine setting at the mode that’s going to be
used to operate the attachment record the GPM _____.
HEAT LOAD TEST
Locate the correct flow for the attachment in the manual
under the specification section. Adjust the machine to the With the installation kit properly installed and adjusted per
correct GPM. the above procedure, conduct the head load test as follows.

NOTE: 1. Connect the flow meter between the tool inlet and outlet
If possible, always set the machine to the highest GPM hoses.
output mode. This will prevent the operator from over
flowing the attachments. 2. With the carrier set in the attachment mode, restrict the
flow meter until a pressure of 1000 psi is achieved. This
3. Once the correct GPM flow is achieved fully open the pressure must be maintained throughout the heat test.
restrictor on the flow meter.
NOTE:
4. With the machine in the attachment mode set in step 2 Closing of the restrictor may be required as the tem-
record the back-pressure. At this point the pressure reading perature increases.
on the pressure gauge is the back-pressure in the circuit.
This pressure must not exceed 200 psi/13.5 bar. Monitor the oil temperature from the flow meter until no
change is noted. Record the time required for oil to stabi-
Excessive back-pressure will slow the attachments opera- lize. Record the surrounding temperature (ambient tem-
tion and lead to premature seal failures and over heating. perature). Record the time required to stabilize ______
minutes.
Record the back-pressure ______ psi.
Record the stabilized oil temperature ______F.
5. Close the restrictor valve on the flow meter until the
attachment relief starts to crack or open. The relief valve Record the ambient temperature ______ F.
opens when the flow rate (GPM), indicated on the flow
meter begins to decline rapidly. Locate the tools operating The “heat rise” is calculated as the stabilized temperature
system relief pressure in the specification section in the minus the ambient temperature.
manual. Adjust attachment relief to specification.

12
FLOW TEST PROCEDURES
Example:
Stabilized Temperature 160°
Ambient Temperature -80°
Heat Rise 80°

The normal operating temperature range of this circuit will


be the typical ambient temperature range for the geographi-
cal area plus the heat rise calculated above. Ensure that
the operating temperature range is lower than 180° for
optimum operation of the attachment.

TROUBLESHOOTING

If adequate pump flow is available from the carrier pump(s)


but is not getting to the attachment, consult your service
representative and review the following:

1. Attachment valve(s) are not actuating. Review all electri-


cal connections that are part of the attachment kit.

2. Ensure proper voltage to the valve(s).

3. Ensure the REG port of the valve is not blocked.

4. Check to make sure the carriers main relief is set to the


manufacturers recommendation and that this value is equal
or greater than the attachment circuit relief.

5. If the valve will not turn off, check the drain (tank) line of
the valve to ensure that the pressure is 50 psi or less.

13
DEFINITION OF TERMS
Tool: The hydraulic attachment which the auxiliary circuit is intended to power. These may include
hydraulic breakers, compactors, shears, etc.

Operating Pressure: That pressure at which the tool will naturally operate without influence of outside pressure relief
mechanisms. This pressure is an operating characteristic of the tool and cannot be altered by the
end user without changing the tool design.

Relief Pressure: The relief pressure is that pressure at which the circuit will dump fluid in order to protect itself
from damage.

Back Pressure: The pressure at the tool’s connection to the return circuit of the carrier.

Flow Meter: Instrument for testing the operating characteristics of a hydraulic circuit. The data usually
available from this device are pressure (psi/bar), flow (gpm/lpm) and temperature (°F/°C).

Restrictor Valve: A valve on the flow meter which allows the user to simulate an operating tool by adding a
pressure load (through restriction) to the circuit. This feature is used to evaluate relief settings
and flow ratings at pressure.

V60/V65/V100 Valves: A priority flow control valve manufactured by Stanley Hydraulic Tools. Allows for optimum
operation of any attachment by providing the proper amount of flow for operation of the tool the
“priority” aspect allows the attachment to function properly if another control function is activated.

Inlet Flow: The hydraulic oil supplied to the “IN” port of the tool or valve.

Regulated Flow: The flow of oil supplied to the tool by the V60/V100 valve.

By-Pass Flow: The oil flow that is supplied by the carriers pump, but not used in the operation of the
attachment. By-pass flow equals inlet flow (to the valve) minus the regulated flow.

Pressure Line: The hydraulic line(s) which supply pressurized oil from the pump to the valve or tool.

Return Line: The hydraulic line which connects the “OUT” port of the tool to the tank circuit of the carrier.

Cracking Pressure: The pressure at which the relief valve starts to open. Can be seen by a drop in the flow rate as
shown by the flow meter.

Full Open Pressure: The pressure at which the relief valve is completely open dumping all system flow to the tank.

Ambient Air The temperature of the outside air.


Temperature:

Stabilized The temperature at which the carrier hydraulic system temperature will stop rising during
Temperature: testing or operation.

14
SPECIFICATIONS
Performance
Centrifugal Force............................................................................................................................................6400 lb/2903 kg
Developed Frequency..............................................................................................................................................2000 vpm

Dimensions and Weights


Spread Between Pins .......................................................................................................................................14 in./35.6 cm
Baseplate Size ...................................................................................................................................................26 in./ 66 cm
Overall Length .....................................................................................................................................................34 in./86 cm
Width Inside Bracket ......................................................................................................................................10.25 in./26 cm
Overall Width.....................................................................................................................................................23.5 in./60 cm
Overall Height ...................................................................................................................................................27.5 in//70 cm
Weight ...............................................................................................................................................................850 lb/386 kg
Standard Mounting Pin Diameter ........................................................................................................................... Universal*

*Contact your dealer for appropriate mounting hardware for your application.

Hydraulic Requirements
Minimum Flow .................................................................................................................................................12 gpm/45 lpm
Maximum Flow ................................................................................................................................................25 gpm/95 lpm
Optimum Flow..................................................................................................................................................13 gpm/49 lpm
Normal Operating Pressure .........................................................................................................................2000 psi/138 bar
Back Pressure .......................................................................................................................... Not to Exceed 250 psi/17 bar
Relief Setting.................................................................................................................................................2500 psi/172 bar

Miscellaneous Part Number


Flow Meter..................................................................................................................................................................... 29085

TORQUE TABLE
General Item No. Swivel Top Item No. Description Apply Ft/Lb Nm
27 --- HHCS 3/8-16 UNC Grade 8 Anti-Seize 35 47
3, 15, 22 6 HHCS 1/2-13 UNC Grade 5 Anti-Seize 75 101
31 --- HHCS 1/2-13 UNC Grade 8 Anti-Seize 85 115
25 1 HHCS 5/8-11 UNC Grade 8 Anti-Seize 180 244

FLAT TOP MOUNTING DIMENSIONS 12.00 R.125

11/16

1.54

3.00
6.00 11.50

NOTE: Weights, dimen-


sions and operating
CARRIER SIDE specifications listed on
this sheet are subject to
change without notice.
Where specifications are
14.00 critical to your application,
please consult the dealer.

15
HS6008F PARTS ILLUSTRATION
46

47

48

49

50

3
2
4

19
52
35 8

5
53
44 40
45 9
6
36 41
43
34 1
10 7
8 54

41 51
39

13

31

43

47 14 2
42

37
2 19
15

16
18 20 17
18
17
30
13 20
21
19 33 22
2
32 14
2
31
24 23
25
55
12
30

29

28

27
26

46
47

16
HS6008F PARTS LIST

Item Part No. Qty Description Item Part No. Qty Description
1 20652 1 Upper Frame, Swivel Top 40 360033 1 Hose
2 371050 20 Washer 41 372083 2 Decal, HS-6000
3 370256 4 Capscrew 42 29610 1 CE Specification Plate
4 370409 1 Capscrew 43 09163 2 Decal, Stanley
5 206106 1 Spacer 44 350241 1 Square Head Plug
6 372055 1 Dowel Pin 45 28841 1 Cap
7 47351 1 Decal, Composite Warning 46 370359 6 Capscrew
8 25803 2 Double Swivel, -12 47 371061 12 Washer
9 206105 1 Lower Bearing 48 206154 1 Retainer Plate
10 371501 1 Nylock Nut 49 206104 1 Upper Bearing
11 ----- -- NO ITEM 50 35379 1 Rotation Top Weldment
12 47352 1 Decal, Lift Point 51 ----- -- No Item
13 30167 4 Shock Mount 52 12549 1 Flow Control Cartridge
14 371500 32 Nylock Nut 53 25109 1 Plug
15 370250 16 Capscrew 54 12550 1 Check Valve Cartridge
16 206024 1 Bearing Cover HS-6000 55 21896 1 Adapter Plate, M-30 Motor
17 06330 2 O-ring
18 206019 2 Bearing 21654 1 Motor Seal Kit 13 gpm Motor
19 372003 3 Grease Fitting 206020 1 Motor Seal Kit 9 gpm Motor
20 206028 2 Bearing Carrier 67936 1 Motor Seal Kit (Permco)
21 206022 1 Mass Weight Assembly
22 370252 16 Capscrew
NOTE: Use Part Number, Part Name and Com-
23 33688 1 Shoe Weldment
pactor Serial Number when ordering.
24 371061 8 Washer
25 370352 8 Capscrew
26 04860 1 Straight Thread Elbow 90°
27 370155 4 Capscrew
28 371056 4 Washer
29 206029 1 Inlet Manifold
30 00834 2 O-ring
31 02504 4 Capscrew
32 22061 1 Motor
33 350215 1 Split Flange Set
34 12546 1 Hose Block Assembly
35 02773 1 Straight Thread Connector
36 02112 1 Adapter
Nylock Nut
37 371507 6

38 02773 1 Male Connector


39 360101 1 Hose

17
HS6019F, HS6026, HS6027 & HS6100
PARTS ILLUSTRATION

18
HS6019F, HS6026, HS6027 & HS6100
PARTS LIST
Item Part No. Qty Description Item Part No. Qty Description
1A 35887 1 Upper Frame Weldment, 14 in. Center 37 19276 1 Sticker, GPM
1B 39737 1 Upper Frame Weldment, 1/4 Yd. Wainroy 38 21896 1 Adapter Plate Only
1C 65740 1 Upper Frame Weldment, Flat Top 39 35791 1 Hose
2 371050 38 Washer 40 35790 1 Hose
3 370256 2 Capscrew 41 372083 2 Decal, HS-6000
4 47351 1 Decal, Composite Warning 42 29609 1 CE Specification Plate
5 47352 1 Decal, Lift Point 43 ---- -- NO ITEM
6 ---- -- NO ITEM 44 28841 1 Cap
7 09163 1 Decal, Stanley logo 45 350241 1 Square Plug
8 ---- -- NO ITEM 46 35702 1 Flow Control Cartridge
9 ---- -- NO ITEM 47 25109 1 Plug
10 ---- -- NO ITEM 48 370353 6 Capscrew
11 ---- -- NO ITEM 49 20876 12 Washer
12 ---- -- NO ITEM 50 371514 6 Nut
13 30167 4 Shock Mount
14 371500 32 Nylock Nut, 1/2-13UNC 21654 1 Motor Seal Kit 13 gpm Motor
15 370250 16 Capscrew Motor Seal Kit 9 gpm Motor (Commer-
206020 1
cial Intertech)
16 206024 1 Bearing Cover
67936 1 Motor Seal Kit (Permco)
17 06330 2 O-ring
18 206019 2 Bearing
NOTE: Use Part Number, Part Name and Com-
19 372003 2 Grease Fitting
pactor Serial Number when ordering.
20 206028 2 Bearing Carrier
21 206022 1 Mass Weight Assembly
22 370252 16 Capscrew
23 33688 1 Shoe Weldment
24 371061 8 Washer
25 370352 8 Capscrew
26 04860 1 Straight Thread Elbow 90°
27 370155 4 Capscrew
28 371056 4 Washer
29 206029 1 Inlet Manifold
30 00834 2 O-ring
31 02504 4 Capscrew
32 206025 1 Motor/Adapter Plate Assy.
- 22061 1 Motor only
33 350215 1 Split Flange Set 12SF
34 35704 1 Hose Block Assy. w/ Cartridge

35 02773 2 Connector

36 02112 1 Adapter

19
STANLEY
Stanley Hydraulic Tools
3810 SE Naef Road
Milwaukie, Oregon 97267
503-659-5660 / Fax 503-652-1780
www.stanleyhydraulic.com

20

You might also like