IJSRD - International Journal for Scientific Research & Development| Vol.

3, Issue 05, 2015 | ISSN (online): 2321-0613

A Review on Biomass Cook Stove

Hitendra A Dabhi
M.E. Student (Thermal Engineering)
Department of Mechanical Engineering
A. D.Patel Institute of Technology, New V.V. Nagar, Gujarat-388121
Abstract— With respect to global issues of sustainable
energy and reduction in greenhouse gases biomass energy is
one of the key sources of renewable energy as a potential
source of energy in the future. Improved cooing stove can
bring significant benefits to rural publics due to reduced fuel
consumption and improved air quality. This work has been
carried out to develop, design and manufacture an applicable
type biomass stove by using locally available biomass fuels
like bamboo and neem wood. Biomass cook stove can be
used in applications like cooking and space heating problem.
This paper summarizes the research literature referred
relative to the Biomass cook stove. Fig. 1: Biomass cook stove principle
Key words: Cook Stove, Biomass, Water Boiling Test The rise in temperature devolatizes the biomass to
give off pyrolytic gases and a flame front is established in
I. INTRODUCTION the bed which propagates towards the grate leaving behind a
hot char zone at the top. A complex thermo-chemical
A. Combustion:
reaction takes place to produce a combustible gas.
As pyrolysis gases are emitted they will diffuse and mix The gas so produced passes through the hot char
with the surrounding air. If proper mixing with O 2 occurs zone allowing the tar (heavy hydrocarbon) to be cracked to
before leaving the reaction zone, and sufficient energy is give a relatively clean fuel gas. The product gases passing
available then the pyrolysis gases will combust. through the hot char zone react with the hot chars giving off
B. Biomass cook stove: relatively a clean energy rich gas.
These gases coming out of the bed typically
Biomass cook stove is basically a combustion device which
contains 16% CO, 12% H2, 3% CH4, 12% H2O (as gas),
burns biomass fuel more efficiently with reduced amount of
some higher hydrocarbons (5-6%) and remaining being N2.
emission and offers cleaner cooking energy solutions.
The gases when allowed to mix with the secondary air
Converting the fuel’s chemical energy into thermal
supplied directly to the combustion chamber burns with a
energy is done by combustion, thermal energy produced is
brilliant flame if the air fuel mixture is proper.
transferred to the cooking vessel by cook stove.
1) Natural draft- The easiest approach to obtain air into the
1) Types of Biomass Cook Stove;
combustion chambers is through naturally inducing air
The various types of Biomass cook stove are:
in which ambient air is introduced in as the hot air rises
 According to combustion type (Since cold air is heavier than the hot air).
 Direct Type 2) Forced draft- In this case the air is forced by using a
 Gasifier Type fan. Ac supply is used to supply such a fans.
 According to draft type 3) Direct combustion- The majority of the stoves is a
 Natural draft direct combustion type of stoves where solid-fuel burns
 Forced draft directly. The famous amongst direct combustion stove
 According to construction Type is design of Larry Winiarski the popular Rocket stove.
 Metallic 4) Gasifier Type- In the gasifier stove combustion takes
 Ceramic place in two different parts. In the first part the fuel get
 Hybrid burns and release gases while in the second stage at the
upper side of the stove air mixes and burns these gases.
C. Biomass Cook Stove: Gasifier stoves generally are quick-heated, energy and
The system comprises of a cylindrical reactor core of mild emissions efficient, lightweight, portable, and produce
steel with an external insulating cladding and a tapered bio char.
combustion chamber with air holes for secondary air supply
to be mixed with the product gas before combustion. II. LITERATURE REVIEW
In such a stove a packed bed of dry biomass (solid
This section summarizes the research literature referred
fuel) is burnt at the top and controlled quantity of air is
relative to the biomass cook stove.
supplied in the upward direction that causes partial
combustion of the biomass. A. Jessica Tryner, Bryan Wilson, Anthony Marchese [1]:
Five different configurations cookstoves were tested by
using two different fuels to determine how changes in stove
design, fuel type, and operating procedure affected

All rights reserved by www.ijsrd.com 465

 A Review on Biomass Cook Stove
(IJSRD/Vol. 3/Issue 05/2015/108)

performance in terms of efficiency, carbon monoxide (CO) C. Murari Mohan Roy and Kenny W. Corscadden [3]
emissions, and particulate matter (PM) emissions. This study presents combustion and emission results
obtained using an Environmental Protection Agency (EPA)
wood stove for 15 biomass briquettes produced from a range
of feedstock including hay and switch grass.

Fig. 2: Five cook stove Tested

1) Stove 1:
Large and equipped with a chimney.
64 cm in height, weighed 37 kg.
Constructed primarily from steel sheet metal.
A refractory material lined the inside of the
combustion chamber and the area under the pot.
2) Stove 2:
Modified version of Stove 1 in which a cylindrical sheet
metal duct was added above the secondary combustion zone
to direct the flow of hot gases closer to the bottom of the
pot. Fig. 3: Emission measurement equipment’s
3) Stove 3: Non-waxed woody heating value of 17.91 MJ/kg.
Pot skirt was added. Grassy briquettes have an average heating value of 17.04
Chimney inlet was moved from the area under the MJ/kg. Waxed briquettes have an average heating value of
pot to the side of the pot skirt to force the hot gases to flow 28.89 MJ/kg. Overall combustion efficiency of grassy
around the sides of the pot. briquettes (74.64%) is very similar to that of woody
4) Stove 4: briquettes (74.21%).
It is 30 cm in height and was constructed of various steel 1) Emission Test
alloys. CO emission has a strong relation with excess air factor the
5) Stove 5: higher the excess air factor the lower the CO emissions.
The Peko Pe stove was also a small stove without a Grassy briquettes showed less average CO emissions (1718
chimney. mg/N m3) than that of woody briquettes (1890 mg/Nm3).
It is 25 cm in height and weighed 2.7 kg and was Grassy briquettes showed higher NOx emissions
constructed using 23 gauge stainless steel sheet metal. than woody briquettes, but SO2 emissions are very similar
Emissions of particulate matter with diameter of for both briquettes.
less than 10 μm were measured gravimetrically. CO D. Nordica MacCarty, Dean Still, Damon Ogle [4]:
emissions were measured at 1 Hz with Testo 335 and Testo
350 flue gas analyzers. Performance of 50 different stove designs was investigated
6) General Conclusion by Water Boiling Test (WBT) Version 3.0 to compare the
1) The measured emissions were lower when wood fuel use, carbon monoxide (CO) and particulate matter (PM)
pellets were used as fuel instead of corn cobs. emissions.
2) Stoves 1, 2, and 3 generally produced much higher Stoves tested fell under 6 main categories:
emissions than both Stoves 4 and 5. 1. Simple stoves without combustion chambers.
3) Stove 5 exhibited the lowest emissions overall. 2. Stoves with rocket-type combustion chambers
Unlike emissions thermal efficiency was not 3. Gasifier stoves
affected by fuel type. 4. Fan-assisted stoves
4) The thermal efficiency of a given design is 5. Charcoal-burning stoves
expected to depend primarily upon stove geometry. 6. Wood burning stoves with chimneys.
B. T. B. Reed and Ronal Larson [2]:
The cookstove working according to downdraft gasifier
principle was developed and evaluated.
Parameters measured-
 Density is about 0.045 g/cm3.
 It has moisture content about 19.3% on dry basis
and 16.4% on wet basis.
 The fuel consumption rate is 1.89 kg/h and it has a
thermal efficiency of about 10.6%.

All rights reserved by www.ijsrd.com 466

 A Review on Biomass Cook Stove
(IJSRD/Vol. 3/Issue 05/2015/108)

Fig. 5: Model of cook stove

1) Specification of stove and measurement-
 The stove works on natural draft mode.
 The thermal efficiency of the stove was recorded at
about 26.5% and it can be started, operated and
stopped with very low emissions.
 It can use a wide variety of biomass fuels.
 The produced wood gas burns with a blue flame
like liquid petroleum gas with a flame temperature
of 736°C.
Fig. 4: various cook stove used
 During the testing the temperature of the outer
Aprovecho developed the Portable Emissions
surface of stove was recorded as about 105°C,
Monitoring System (PEMS), which performs as well as the
which indicates that there is still a chance to
laboratory system, but is less expensive and less
minimize conduction and radiation heat losses from
complicated. The PEMS consists of:
the outside skirt of cookstoves.
 Collapsible suitcase-sized emissions collection
 The flame temperature was recorded by a K-type
structure and exhaust system.
thermocouple and it was about 736°C during the
 Flow grid, temperature sensor, and pressure drop
peak hour of combustion.
for exhaust flow measurement.
 However, with increase in the efficiency of stove,
 City Electrochemical CO sensor.
the amount of CO2 and CO emission inside the
 Telaire NDIR CO2 sensor. kitchen has been reduced, which was measured
 Specially-designed laser PM sensor for light- with the help of gas analyzers. It was found in the
scattering measurement of particulate matter. range of 18–20 and 1–3ppm respectively and
1) General Conclusion Made: within safe limits as recommended by the WHO.
Stoves without well-designed combustion chambers may
reduce fuel use in comparison to the three-stone fire but do F. Victor M. Berrueta, Rufus Edwards, Omar Masera [6]:
not necessarily decrease an emissions of CO and PM. This paper presents an energy evaluation of the Patsari
By using a pot skirt we can reduce fuel use and cookstove an efficient wood-burning cookstove developed
emissions by 25–30%. in Mexico. The evaluation uses three standard protocols:
With well operation gasifier stoves can reduce  WBT which quantifies thermal efficiency and
particulate matter substantially, averaging 90% firepower.
improvement over the three-stone fire.  The controlled cooking test which measures
Forced air stoves reduced fuel use by an average of specific energy consumption associated with local
40% and emissions by 90% over the three-stone fire. cooking tasks
E. N .L .Panwar and N. S. Rathore [5]:  Kitchen performance test which evaluates the
behavior of the stoves in-field conditions and
This paper addresses about the studies of wood gas stove in
estimates fuel savings.
meeting cooing energy requirement.
Result showed that
 The efficiency measured by stove was 30%.
 The power of the devices varied between 6.4 kW to
9kW.

All rights reserved by www.ijsrd.com 467

 A Review on Biomass Cook Stove
(IJSRD/Vol. 3/Issue 05/2015/108)

 The fuel savings achieved by the Patsari were 55%

to 65% in comparison with the traditional one.
 With sound technical design, critical input from
local users and proper dissemination strategies
improved stoves can significantly contribute to
improvements in the quality of life of rural people
with potential benefits to the surrounding
environment.
G. Ranjit Powar, Paris Yadav, Manish Chavan [7]
Highlighted the performance evaluation of forced draft cook
stove.
Fig. 7: Mass loss versus time for wood
 The thermal efficiency measurement-
The radiation from the char bed to the vessel is
For pellet 40.33 per cent, Neem 36.47 per cent and
shown to contribute about 6 ± 1% to the efficiency.
Tur 33.43 per cent respectively.
 Specific fuel measurement- I. Marian Bojko, Michal Branc[9] :
Specific fuel consumption of a stoves were 1, 1.2, It deals with the numerical model of combustion process of
1.44 kg/h for pellet, Neem, and Tur respectively. wood. Cross section through stove was created for
 Power output measurement- evaluation of numerical simulation. The temperature contour
The power output of the cook stove for pellet, are shown in figure below:
Neem and Tur were found to be 3, 2 and 1.8 kW
respectively.

Fig. 6: Comparison of cold and hot eater boiling test

It was observed that pellet shown excellent results Fig. 8: Simplified model geometry of stove
in terms of thermal efficiency and power output rating as
compared with conventional fuel i.e. Tur and Neem. Pellet
was also found convenient to handling.
H. H. S. Varunkumar, N.K.S Rajan, H.S. Mukunda [8]:
The work reported here is concerned with a detailed
thermochemical evaluation of the flaming mode behavior of
a stove.
Reactive flow computational studies using the
measured gas composition over the fuel bed are used to
simulate the thermochemical flow field and heat transfer to
the vessel.
The overall flaming mode thermal efficiency of the
stove is 50–54% and the convective and radiative
components of heat transfer are found to be 45–47 and 5–
7% respectively. The efficiency estimates from reacting Fig. 9: Temperature contour results
computational fluid dynamics (RCFD) compare well with
J. J. Shankar kauley, Aniruddha Pandit [10]:
experiments. The results shows that:
 The calculated data compare well with the This work presents a detailed theoretical study of solid fuel
experimental data. combustion in a domestic stove. In this work different
 The heat transfer is a strong function of the vessel steady state as well as unsteady state combustion models
size such that efficiency increasing with increasing have been formulated, which include the description of all
the diameter of the vessel. the chemical and physical processes taking place during the
solid fuel combustion inside the stove. Steady state models
involve the calculation of effective maximum flame
temperature, suction of combustion air created by hot flue
gases inside the stove and the propagation of ignition front

All rights reserved by www.ijsrd.com 468

 A Review on Biomass Cook Stove
(IJSRD/Vol. 3/Issue 05/2015/108)

inside the stove. Unsteady state mathematical model The heat release rate of the improved cookstove
involves all the processes occurring simultaneously or (metal stove with insulation) is 82% higher than the
sequentially during the solid fuel combustion such as traditional cookstove. Hence, the efficiency of the improved
moisture evaporation, devolatilization, pyrolysis and cookstove was 1.8 times higher than the traditional
homogeneous and heterogeneous combustion reactions. cookstove.
A clay stove can hold 3.6 times of heat energy as
compared to metal cookstove made of stainless steel.

REFERENCES
[1] Jessica Tryner and Bryan D.Willson, “The effects of
fuel type and stove design on emissions and efficiency
of natural-draft semi-gasifier biomass cookstoves”, July
2014
[2] T. B. Reed and E. Anselmo, “Testing & Modelling the
wood gas turbo stove”, July 1996
[3] Murari Mohon Roy and Kenny W. Corscadden, “An
experimental study of combustion and emissions of
biomass briquettes in a domestic wood stove”, May
2012
[4] Nordica MacCarty and Dean Stil, “Fuel use and
emissions performance of fifty cooking stoves in the
Fig. 10: Effect of bed height and flame temperature on laboratory and related benchmarks of performance”,
suction created by flue gases. June 2010
[5] N.L. Panwar and N.S. Rathore, “Design and
performance evaluation of a 5kW producer gas stove”,
April 2008
[6] Vıctor M. Berrueta and Rufus D. Edwards, “Energy
performance of wood-burning cookstoves in Mexico”,
June 2007
[7] Ranjit Powar and Paris Yadav, “Performances
Evaluation of Force Draft Gasifier Based Cook Stove”,
May 2014
[8] S.varunkumar, “Experimental and computational
Fig. 11: Validation of Temperature results studies on gasifier based stove”, August 2011
This unsteady state model gives the temperature [9] Marian Bojko, “A definition of the mathematical order
profiles at different locations inside the stove and fuel mass of combustion process in the stove”, January 2009
loss (combustion) rate, which can be further used to [10] Shankar kausley and Aniruddha Pandit, “ modelling of
calculate the power delivery by the stove during solid fuel stoves”, October 2009
combustion. The model shows good agreement with the
experimental results. These models can be used to find the
effect of stove geometry and fuel properties on the stove
performance parameters such as effective maximum flame
temperature, suction created inside the stove, propagation of
ignition front inside the stove, and fuel burn rate, which play
an important role in the design of such stoves for maximum
thermal efficiencies.

III. CONCLUSION
High power hot start give better results than the cold power
since it minimizes the initial thermal losses of the system
which occurs during cold start phase.
Thermal efficiency can be increased by using fan
since it provide better mixing of air with fuel and makes the
combustion proper.
Designed forced draft cook stove has efficiency
near about 40% and natural draft cook stove has efficiency
about 25%.
Increased air flow from the top that is secondary air
caused enhanced recirculation around the fuel bed brings in
more oxygen that reacts closer to the surface and transfers
additional heat enhancing the combustion in the fuel bed.

All rights reserved by www.ijsrd.com 469