Sl. Quantity Measured / Instrument Range/Frequency Calibration Measurement Capability ( ) Remarks

Laboratory Perfect Calibration Centre Pvt. Ltd., No.
84 First Floor, Times Corner,

Gengu Reddy Road, Egmore, Chennai, Tamil Nadu
Accreditation Standard ISO/IEC 17025: 2005
Certificate Number CC-2207 (in lieu of C-0399, C-0243,C-0446) Page 1 of 26
Validity 18.06.2017 to 17.06.2019 Last Amended on 01.08.2017
Sl. Quantity Measured / Range/Frequency *Calibration Measurement Remarks

Instrument Capability (±)
ELECTRO-TECHNICAL CALIBRATION
I. SOURCE
1. Temperature
Simulation$
(Temperature Indicator /
Controller / Recorder/
Scanner)
RTD Type (-) 200°C to 800°C 0.56°C Using Process Calibrator
‘J’ Type Thermocouple (-) 200°C to 1200°C 0.8°C By Direct Method
‘K’ Type Thermocouple (-) 200°C to 1350°C 0.81°C
100°C to 1750°C 1.14°C
‘R’ Type Thermocouple 100°C to 200°C 1.1°C
200°C to 1750°C 0.82°C
‘S’ Type Thermocouple 600°C to 1820°C 0.94°C
B’ Type Thermocouple (-)200°C to 400°C 0.59°C
T’ Type Thermocouple (-) 200°C to 0°C 0.43°C
0°C to 1300°C 0.37°C
‘N’ Type Thermocouple (-) 200°C to 1000°C 0.29°C
‘E’ Type Thermocouple
2. Time Interval (Measure) 1 sec to 1 min 0.08 to 0.13 sec Using Digital Timer
1 min to 24 hr 0.13 to 22 sec by Comparison Method
3. Temperature
Simulation♣
(Temperature Indicator /
Controller / Recorder/
Scanner )
RTD’ Type -200°C to 800°C 0.82°C Using Multifunction
‘J’ Type Thermocouple -200°C to 1200°C 1.45°C Calibrator by Direct
‘K’ Type Thermocouple -200°C to 1350°C 0.96°C Method
‘R’ Type Thermocouple 0°C to 1750° 2.81°C
‘S’ Type Thermocouple 0°C to 1750°C 2.32°C
Vishal Shukla Avijit Das

Convenor Program Director
Laboratory Perfect Calibration Centre Pvt. Ltd., No.84 First Floor, Times Corner,

‘B’ Type Thermocouple 600°C to 1820°C 2.88°C

‘T’ Type Thermocouple -200°C to 400°C 0.69°C
‘N’ Type Thermocouple -200°C to 1300°C 0.52°C
‘E’ Type Thermocouple -200°C to 1000°C 0.40°C
4. Time Interval (Measure) 1 sec to 1 min 0.2 to 0.23 sec Using Digital Timer
1 min to 24 hr 0.23 to 22 sec by Comparison Method


FLUID FLOW CALIBRATION
1. Air Flow 0.4 to 20 m/s 7.2%rdg Using Anemometer,

(Anemometer Vane Variable Speed Blower for
Type) Air Supply by Comparison
Method


MECHANICAL CALIBRATION
I. DIMENSION (BASIC MEASURING INSTRUMENT, GAUGE ETC.)
1. Calipers$
(Vernier/Dial/Digital)
L.C:0.01mm 0 to 450mm 18.2 µm Using Slip gauge Set
450 mm to 600mm 18.5 µm Grade ‘0’, Caliper
600 mm to 1000mm 19.5 µm Checker, Length bar &
1000 mm to 1500mm 21.3 µm Slip gauge Accessories.
Comparison Method
L.C:0.02mm 0 to 2000mm 20.2 µm IS :3651(Part 1 & 2)
2. External Micrometer/
Ball Micrometer/
Blade Micrometer/
Disc
Micrometer/Flange
Micrometer/Groove
Micrometer/
Spline Micrometer/
Sheet Metal
Micrometer/
Point
Micrometer/Pitch
Micrometer$
L.C.:0.001mm 0 to 25mm 2.0 µm Using Slip Gauge Set
25 mm to 150mm 5.8 µm Grade ‘0’, Optical Flat &
150 mm to 300mm 6.2 µm Parallels, length bar.
300 mm to 600mm 8.5 µm Comparison Method
600 mm to 1000mm 9.2 µm IS:2967


3. Depth Micrometer$
L.C:0.01mm 0 to 150mm 5.82 µm Using Slip Gauge Set
150 mm to 300 mm 8.2 µm Grade ‘0’, Caliper
Checker & Gauge Block
Accessories by
Comparison Method
BIS:6468
4. Internal Micrometer/
Stick Micrometer$
600 mm to 1000mm 8.5 µm Grade ‘0’, Gauge Block
1000 mm to 2000mm 20.0 µm Accessories Set & Length
bar by Comparison
Method as per IS:2966
5. Plunger Type Dial

Indicator$
L.C:0.001mm 0 to 25mm 2.1 µm Using Length Measuring
25 mm to 50mm 2.1 µm Machine by
Comparison Method as
L.C:0.0005mm ± 0.025mm 2.1 µm per IS:2092
6. Lever Type Dial

Indicators$
L.C:0.01mm 0 to 1.6 mm 5.8 µm Using Length Measuring
L.C:0.001mm 0 to 0.6 mm 2.1 µm Machine by Comparison
L.C:0.002mm 0 to 0.2 mm 2.1 µm Method as per IS:11498
7. Plain Plug Gauge/ Up to 100mm 2.1 µm Using Length Measuring

Width Gauge$ 100 mm to 200mm 2.8 µm Machine by
per IS:3455 & IS:7859


8. Snap 3 mm to 200mm 1.4 µm Using Slip gauge Set

Gauge/Adjustable 200 mm to 400mm 1.94 µm Grade ‘0’ by
Snap Gauge, Knife Comparison method as
Edge Gauge, Length per IS:3455, IS:7859 &
Gauge, Height IS:3477
Gauge, Master
Setting Gauge, Gap
Gauge, Distance
Gauge, Depth Gauge,
Bridge Gauge$
9. Dial Depth Gauge$

0 to 100mm 6.0 µm Grade ‘0’ by
Comparison method
10. Feeler Gauge$ Upto 1.0mm 2.9 µm Using Digital Micrometer

by Comparison method
as per IS:3179
11. Bore Dial Gauge$

(Only Transmission
movement)
L.C:0.001mm Upto 3mm 2.1 µm Using Length Measuring
Machine by
Comparison Method
12. Dial Thickness

Gauge$ 0 to 50mm 5.9 µm Using Slip gauge Set
L.C:0.01mm Grade ‘0’ by
Comparison method as
perIS:2092


13. Height Gauge$

(Vernier/Digital/Dial)
L.C: 0.01mm 0 to 300mm 14.8 µm Using Caliper Checker by
0 to 1000mm 15.2 µm Comparison method
IS:2921
14 Pistol Caliper$
Grade ‘0’ by
Comparison method
IS:2092
15. Depth Caliper $

(Vernier/Dial/Digital)
L.C:0.01mm 0 to 300 mm 9.1 µm Using Slip gauge Set
0 to 600 mm 11.1 µm Grade ‘0’, Gauge Block
Accessories & Caliper
Checker by
Comparison Method
IS:4213
16. Dial Caliper

Gauge/Groove Dial/
Inside Caliper
Gauge$ Using Slip gauge Set
L.C:0.01mm 10 mm to 150mm 5.8 µm Grade ‘0’, & Slip gauge
Accessories by
Comparison Method
17. Cylindrical Upto 25mm 2.1 µm Using Length Measuring

Measuring Pins$ Machine by
(Only Diameter) Comparison Method
IS:11103


18. Cylindrical Upto 100mm 2.1 µm Using Length Measuring

Measuring master$ Machine by
(Only Diameter) Comparison Method
IS:4349
19. Thread Measuring 0.17 mm to 6.35mm 2.1 µm Using Length Measuring

Wires Machine by
Comparison Method
IS:6311
20. Thread Plug gauge$ M2 to M100 3.6 µm Using Length Measuring

M100 to M200 3.6 µm Machine
M2 to M100 5.6 µm Using FCDM, Thread

M100 to M200 5.6 µm Measuring Wire &
Cylindrical Setting Master
by Comparison Method
as per IS 2334, IS 4218
(Part I to IV) ,IS 10216,
IS 8999, ANSI/ASME
B.20.1-1983
21. Taper Thread Ring M2 to M50 5.1 µm Using Length Measuring

Gauge$ M50 to M100 5.1 µm Machine by
Comparison Method
IS 2334, IS 4218 (Part I to
IV) , IS 10216, IS 8999 ,
ANSI/ASME B.20.1-1983
22. Thread Ring Gauge$ M3 to M100 3.6 µm Using Length Measuring

M100 to M 200 3.6 µm Machine & Master Setting
Ring by Comparison
Method as per
IS 4218,IS 2334 ,
ANSI/ASME B.20.1-1983


23. Taper Thread Plug M2 to M100 7.5 µm Using FCDM, Thread

Gauge$ Measuring Wire &
Cylindrical Setting Master
by Comparison Method as
per IS 8999, ANSI/ASME
B.20.1-1983
24. Plain Ring Gauge$ Up to 50mm 3.3 µm Using Length Measuring

50 mm to 100mm 3.3 µm Machine & Master Setting
100 mm to 200mm 3.3 µm Ring by Comparison
200 mm to 300mm 5.7 µm Method as per
IS: 3485
25. Flush Pin Gauge$ Up to 200 mm 2.8 µm Using Slip Gauge Set
Grade ‘0’ , Digital
Micrometer and Plunger
Dial gauge by
Comparison Method
26. Coating Thickness 0.01mm to 2mm 1.79 µm Using Standard Foils by

Gauge$ Comparison Method
27. Foils$ Up to 250 m 1.2 µm Using Length Measuring

0 to 5mm Machine by
Comparison Method
28. Setting Rod / Setting Up to 50mm 3.5 µm Using Slip Gauge Set
Piece$ 50 mm to 100mm 3.5 µm Grade ‘0’, Length bar &
100 mm to 200mm 3.5 µm Electronic comparator by
200 mm to 1000mm 4.7 µm Comparison Method


29. Dial Snap Gauge /

Dial Snap Meter$
(Parallelism of Grade ‘ 0’ by
Measuring faces) Comparison Method as
per IS 3455, IS 7859 &
IS 3477
30. V - Block$ Using Lever Dial gauge,

(Parallelism of (250x 200x180)mm Slip Gauge set Grade “0”,
seating faces, 4.2 µm Bevel Protractor by
Perpendicularity, 3.4 µm Comparison Method as
Angle, 14 min per IS 2949
Axis of the shaft) 1.4 µm
31. Ultrasonic
Thickness gauge$
L.C.: 0.1mm 0 to 100mm 70.2 µm Using slip gauges set
grade“0” by
Comparison Method
32. Comparator Stand$ 300 x 300mm 1.7 µm Using Dial gauge by

( Flatness Only) Comparison method as
per IS 6973
33. Straight edge$ Up to 1000mm 6.0 µm Using Electronic Level &

Dial Gauge by
per IS :2220
34. Tri Square$ Up to 500 x 500mm 4.4 µm Using Slip Gauge Set
(Squareness) Up to 500 x 500mm 4.0 µm Grade ‘ 0’, Master
(Parallelism) Square, Plunger dial,
Surface plate by
per IS :2103


35. LVDT Probe with

DRO$
L.C:0.1 µm 0 to 10mm 2.5 µm Using Slip Gauge Set
Grade ‘ 0’ by
Comparison Method
36. V- Anvil Micrometer$

L.C: 0.001mm 0 to 100mm 2.1 µm Using Cylindrical setting
master by Comparison
Method
37. Mandrel 100 mm dia 13.4 µm Using Bench centre with

(Run out only) 200 mm Length dial as per IS 2063,
ISO230-1
38. LVDT Probe with

DRO♣
L.C:0.001mm 0 to 25mm 2.5 m Using Slip gauge set
Grade’0’ by
Comparison Method
39. Surface plate♣ 6000 mm X 3000 mm 1.32

√L+W
m Using Electronic level as
150 per IS:7327,IS:2285,
IS:12937
40. Height Measuring

System♣
L.C:0.001 mm 0 to 600 mm 2.8 m Using Slip gauge Set
Grade ‘0’, Length bar by
Comparison Method
41. Microscope♣
Linear
L.C: 0.0001mm 0 to 300 mm 1.1 m Using Graticules scale by
Angle 0 to 360° 3’ Comparison Method


42. Bench Centre Centre height:300 mm 6.0 m Using Mandrel & Dial
Parallelity Admit between Indicator as per
Co- axiality of Centre:750mm IS:5980:2000
centre♣
43. Profile projector /

Video Measuring
Machine♣
Linear
L.C:0.001mm 0 to 300 mm 17.75 m Using Graticules scale ,
Angle L.C:36” 0 to 360 ° 2’ 16” ‘0’ Grade Slip gauge set
Magnification 5X to 100X 2.5% by Comparison Method
44. Gauge Block

Measuring Fixture
with Electronic
System♣
L.C:0.01 m 0 to 100mm 0.09 m Using Grade ‘K’ Pair
Gauge Block by
Comparison Method
45. Tape and Scale

Calibrator♣
L.C:0.001mm 0 to 1000 mm 18.7 m Using Slip Gauge Set
Grade ‘0’, Length Bar,
Lever Dial Gauge by
Comparison Method
II. ACCELERATION & SPEED
1. Tachometer / RPM$
Contact Type 150 rpm to 2500 rpm 0.82% Using RPM Indicator with
Non contact type 150 rpm to 50,000 rpm 0.87% Electric Motor by
Comparison Method


2. Indicator of
Centrifuge / RPM♣
Meter 60 to 25,000 rpm 0.06% of rdg Using Digital Tachometer
Comparison Method
III. ACCOUSTICS
1. Sound Level Meter$ 1kHz Using Sound Level

94 dB & 114 dB 0.8 dB Calibrator by Direct
Method as per
IS:9779:1981
IV. WEIGHTS
1. Mass$ 1 mg 0.013 mg Using E1 Class Standard

(Class F1 accuracy 2 mg 0.013 mg Weights and Electronic
& Coarser) 5 mg 0.013 mg Weighing Balance
10 mg 0.013 mg (Readability : 0.01mg)
20 mg 0.013 mg Substitution method of
weighing and ABBA
weighing cycle based on
OIML R111-1
50 mg 0.02 mg Using E1 Class Standard

100 mg 0.02 mg Weights and Electronic
200 mg 0.02 mg Weighing Balance
500 mg 0.02 mg (Readability: 0.01mg)
1g 0.03 mg Substitution method of
2g 0.04 mg weighing and ABBA
5g 0.04mg weighing cycle based on
10 g 0.05 mg OIML R111-1
20 g 0.06 mg


Class F1/M1 50 g 0.09 mg Using E1& F1 Class

accuracy & Coarser 100 g 0.10 mg Standard Weights and
200 g 0.15 mg Electronic Weighing
500 g 0.013 g Balance
1 kg 0.08 g (Readability:
2 kg 0.09 g 0.1mg/10mg)
Substitution method of
weighing and ABBA
OIML R111
5 kg
0.49 g Using F1 Class Standard
10 kg
0.49 g Weights and Electronic
20 kg
1.0 g Weighing Balance
(Readability : 500mg)
Substitution method of
weighing and ABBA
OIML R 111
V. WEIGHING SCALE AND BALANCE
1. Weighing Balance
Calibration of
Electronic Weighing
Balance$
Class II and coarser
Readability : 0.01mg Up to 200 g 0.04 mg Using E1 Class standard
weights, as per OIML R
76-1
Readability : 10 mg Up to 4 kg 0.09 g Using E1 and F1 Class

Standard Weights
as per OIML R 76-1


Readability : 500 mg Up to 30 kg 1.30 g Using F1 & M1 Class

Standard Weights as per
OIML R 76-1
2. Calibration of
Electronic Weighing
Balance♣
Class I and coarser
Readability : 0.001 Up to 6.1 g 0.01 mg Using E1 Class Standard
mg Weights as per OIML R
76-1
Readability : 20 g Up to 200 kg 41.0 g
Readability : 50 g Up to 300 kg 50.0 g
VI. VOLUME
1. Micro Pipettes$ 10 l to 50 l 0.11 l Using Precision balance

Readability : 50 l to 100 l 0.11 l and Distilled Water Of
0.01/0.1 mg 100 l to 1000 l 0.27 l Known Density By
1 ml to 5 ml 0.14 l Gravimetric Method as
per ISO 8655-6 & ISO
4787
2. Burette/ Pipette$ Using Precision balance

Readability : 0.01/0.1 1ml to 50 ml 0.14 ml and Distilled Water Of
mg 50 ml to 100 ml 0.14 ml Known Density By
Gravimetric Method as
per ISO 4787
3. Measuring Cylinder/ 100 ml to 200 ml 0.19 ml Using Precision balance

Graduated Jar$ 200 ml to 500 ml 0.63 ml and Distilled Water Of
Readability : 10 mg 500 ml to 1000 ml 0.73 ml Known Density By
& 100 mg 1000 ml to 2000 ml 1.32 ml Gravimetric Method as
2000 ml to 5000 ml 3.1 ml per ISO 4787


4. Volumetric Flask$ 10 ml to 100 ml 0.14 ml Using Precision balance

Readability 100 ml to 200 ml 0.14 ml and Distilled Water By
:0.01mg/ 10 mg/ 200 ml to 500 ml 0.63 ml Gravimetric Method as per
100 mg 500 ml to 1000 ml 0.73 ml ISO 4787
1000 ml to 2000 ml 1.31 ml
2000 ml to 5000 ml 3.1 ml
VI. TORQUE GENERATING DEVICES
1. Torque Wrench / 2 Nm to 20 Nm 2.91% Torque transducer with

Torque Screw 20 Nm to 200 Nm 2.61% Indicator & Fixtures
Driver/Torque 200 Nm to 2000 Nm 1.32% IS/ISO 6789:2003
Spanner
(Type-I & II All
Classes)
VII. UTM, TENSION CREEP AND TORSION TESTING MACHINE
1. Uni- Axial Testing

Machines♣
Compression 5 N to 300 kN 0.8% Using Load cell with
Tension 5 N to 300 kN 0.8% Indicator based on
IS:1828
VIII. HARDNESS TESTING MACHINES
1. Shore Hardness
Tester$
Shore A 0-100 Shore A 0.6 shore A Using Load cell with
Shore D 0-100 Shore D 0.6 shore D Indicator based on ASTM
D 2240-05
2. Verification of HRA 1.0 HRA Using Standard Test

Rockwell Hardness blocks as per IS:1586-
HRB 1.0 HRB
Tester♣ 2:2012 in- by Indirect
HRC 1.0 HRC Method


3. Verification of HBW 2.5/187.5 1.2% Using Standard Test

Brinell Hardness 1.3% blocks as per
HBW 5/750
Tester♣ 1.2% IS:1500-2:2013 IN by
HBW 10/3000
Indirect method
4. Verification of HV 5 1.6% Using Standard Test

Vickers Hardness HV 10 1.6% blocks as per
Tester♣ HV 20 1.6% IS:1501-2:2013 in by
HV 30 1.6%
Indirect Method
HV 50 1.6%
IX. PRESSURE INDICATING DEVICES
1. Pneumatic 0 to 20 bar 0.06%rdg Using Digital Pressure

Hydraulic$ Calibrator DPI 610 and
0 to 700 bar 0.18%rdg
(Pressure Gauge/ External transducer by
Pressure Indicator/ Comparison Method as
Switch/ per DKD-R6-2
Transmitters/
Manometer/
Compound Gauge/
Transducers With
Indicators)
2. Vacuum (-)0.1 bar to (-)0.9 bar 0.7%rdg Using Digital Pressure

Gauge/Switch/ Calibrator DPI 610 by
Transmitters/ Comparison Method as
Transducer With per DKD-R6-1
Indicators/
Compound Gauge$


3. Pressure (-)350 mbar to 350 mbar 0.24 % rdg Using Digital low pressure
Magnehelic Calibrator by Comparison
Gauges / method as per DKD-R6-1
Differential & DKD-R6-2
Pressure Gauge#
4. Pressure Gauge/ 0 to 20 bar 0.33 % rdg Using Digital Pressure

Pressure Indicator / Calibrator by Comparison
0 to 700 bar 0.20 % rdg
Switch/Transmitters Method as per DKD-R6-1
/Manometer/
Compound Gauge/
Transducers with
Indicators♣
5. Vacuum Gauge / (-) 0.1bar to (-) 0.85 bar 0.95 % rdg Using Digital Pressure
Vacuum Indicator/ Calibrator by Comparison
Switch / Method as per DKD-R6-1
Compound Gauge / & ISO: 3567
Transmitters and
Transducer with
Indicator♣
MECHANICAL CALIBRATION – MOBILE
1. Calipers:
(Venire / Dial /
Digital)
L.C:0.01mm 0 to 1000 mm 15.0 µm Using Slip gauge Set
grade ‘0’, Caliper
Checker, Length bar &
Slip gauge Accessories
IS:3651(Part I & II)


2. External
Micrometer/ Ball
Micrometer/ Blade
Micrometer /Disc
Micrometer /Flange
Micrometer/
Groove
Micrometer/Spline
Micrometer /Sheet
Metal
Micrometer/Point
Micrometer/Pitch
Micrometer
100 mm to 600mm 4.5 µm Grade ‘0’, Optical Flat &
Parallels, Length Bar,
Gauge Block Accessories
IS:2967
3. Depth Micrometer
L.C:0.01mm 0 to 300 mm 11.15 µm Using Slip Gauge Set
Grade ‘0’, Caliper
Checker, Gauge Block
Accessories
BIS:6468
4. Internal
Micrometer/ Stick
Micrometer
L.C:0.01 mm 0 to 600 mm 7.1 µm Using Slip Gauge Set
Grade ‘0’, Length Bar &
Gauge Block Accessories
IS:2966


5. Plunger Type Dial

Indicator
L.C:0.001 mm 0 to 25 mm 4.12 µm Using Dial Calibration
Tester IS:2092
6. Lever Type Dial

Indicator
L.C:0.01 mm 0 to 1.6mm 4.86 µm Using Dial Calibration
L.C:0.001mm 0 to 0.6 mm 4.17 µm Tester IS:11498
7. Snap 3 mm to 200 mm 1.74 µm Using Slip Gauge Set

Gauge/Adjustable 200 mm to 400 mm 3.7 µm Grade ‘0’, Slip Gauge
Snap Gauge, Knife Accessories IS: 3455,
Edge Gauge, IS:7859 & IS 3477
Length Gauge,
Height Gauge,
Master Setting
Gauge, Distance
Gauge, Depth
Gauge, Bridge
Gauge
8. Feeler Gauge Up to 1.0 mm 2.78 m Using Digital Micrometer

IS 3179
9. Bore Dial Gauge

( Only
Transmission
Movement)
L.C:0.001mm Up to 2 mm 4.27 m Using Dial Calibration
Tester by Comparison
Method


10. Dial Thickness

Gauge
L.C.: 0.01 mm 0 to 50 mm 5.79 m Using Slip Gauges Set
Grade ‘0’ as per IS 2092
11. Height Gauges

(Vernier/ Digital/
Dial)
L.C:0.01mm 0 to 600 mm 11.1 m Using Caliper Checker
IS 2921
12. Pistol Caliper

L.C.: 0.01 mm 0 to 100 mm 3.7 µm Using Slip Gauge Set
Grade ‘0’ as per IS 2092
13. Depth Vernier

Caliper
L.C.: 0.01 mm 0 to 300 mm 11.6 m Using Slip Gauge Set
Grade ‘ 0’, Gauge Block
Accessories & Caliper
checker as per IS 4213
14. Dial Caliper Gauge/

Groove Dial / Inside
Caliper Gauge
L.C.: 0.01mm 10 mm to 150 mm 3.62 m Using Slip Gauge Set
Grade ‘0’ & Slip Gauge
Accessories by
Comparison Method
15. Flush Pin Gauge Up to 200 mm 2.89 m Using Slip Gauge Set
Grade ‘0’ , Digital
micrometer & Plunger dial


16. Coating Thickness 0.01mm to 2 mm 1.79 m Using Standard Foils by

Gauge Comparison Method
17. Foils 0 to 5 mm 1.59 m Using Digital Micrometer

18. Measuring Pin 1mm to 20mm 2.83 m Using Slip Gauge Set
Grade ‘ 0’ Electronic
Comparator Stand
IS 11103
19. Dial Snap Gauge /

Dial Snap Meter
(Parallelism of
Measuring faces )
L.C: 0.001mm 0 to 100 mm 0.7 m Using Slip Gauge Set
Grade ‘ 0’ as pwe
IS 3455, IS 7859 & IS
3477
20. Plain Plug Gauge Up to 50 mm 2.83 m Using Slip Gauge Set

Grade ‘ 0’ Electronic
Comparator Stand
IS 3455 & IS 7859
21. Setting Rod Up to 50 mm 0.5 m Using Slip Gauge Set

50 mm to 100 mm 1.19 m Grade ‘ 0’, Length bar &
100 mm to 200 mm 1.32 m Electronic Comparator
200 mm to 600 mm 4.7 m Stand by
Comparison Method
22. Three Point 6 mm to 200mm 2.76 m Using Setting Ring Gauge

Micrometer 200 mm to 250mm 5.95 m by Comparison Method


23. V- Block Parallelism 4.2 m Using Slip Gauge Set

(Parallelism of Perpendicular 3.4 m Grade ‘ 0’, Lever dial
seating faces, Angle 15’ 51” Gauge, Bevel Protractor
Perpendicularity, Axis of Shaft 1.4 m As per IS 2949
Angle, Axis of the
shaft)


THERMAL CALIBRATION
1. TEMPERATURE
1. Liquid in Glass (-) 20 to 150°C 0.20°C Using SPRT with Digital

Thermometers$ Indicator and Low
Temperature Bath.
By Comparison Method
Confirming to IS:6274
2. RTD’s, Thermocouple , (-)80 to 100°C 0.24°C Using SPRT with

Digital Thermometer, 100 °C to 600°C 1.42°C Indicator,
Temperature Indicator 600°C to 1200°C 1.96°C S-type Thermocouple
With Sensor, Baths, with Indicator and Low
Temperature Controllers Temperature Bath/ Dry
With Sensor, Data Black Calibrator & Data
Logger, Transmitters logger by Comparison
With Sensors, Method confirming to
Temperature Gauges & EURAMET cg-8 Ver. 2.1
Temperature Switches$
3. Non – Contact 50 °C to 300°C 2.55°C Using IR Thermometer /

Temperature Calibration 300 °C to 1200°C 3.75°C Pyrometer with Digital
Infrared Thermometer & Indicator Black Body
Pyrometer$ Source by Comparison
Method MSL Technical
Guide & OEM Application
note


4. RTD’s, (-) 80°C to 100°C 0.5°C Using SPRT with Digital

Thermocouple , 100°C to 600°C 1.6°C Indicator and
Digital 600°C to 1200°C 2.1°C S-type Thermocouple
Thermometer, with Indicator and Low
Temperature Temperature Bath/ Dry
Indicator With Black Calibrator & Data
Sensor, Baths, logger By Comparison
Temperature Method confirming to
Controllers With DKD-R-5-1,
Sensor, Data EURAMET
Logger, cg-8,Ver 2.1
Transmitters With
Sensors,
Temperature
Gauges &
Temperature
Switches♣
5. Environment (-)80°C to 100°C 0.9°C Using SPRT with Indicator

Chamber, Cold 100°C to 300°C 1.5°C By Comparison Method,
Chamber, Freezer, based on DKD-R-5-7
Incubator,
Autoclave, Oven♣
( Single Point )
6. Environment (-)80°C to 250°C 0.8 to 1.4 °C Using RTD sensor with

Chamber, Cold Data logger (Multi sensor)
Chamber, Freezer, By Comparison Method,
Incubator, based on DKD-R-5-7.
Autoclave, Oven♣
( Multi Point )


7. Furnace♣ 100°C to 600°C 1.39 °C Using SPRT with Indicator

(Single Point) 600°C to 1200°C 1.89 °C R-type Thermocouple
1200°C to1500°C 2.95 °C with Indicator
By Comparison Method,
based on AMS2750E
8. Furnace♣ 100°C to 1200°C 2.79°C Using N - Type

(Multi Point) Thermocouple with Data
logger By Comparison
Method, based on
AMS2750E
II. SPECIFIC HEAT AND HUMIDITY
1. Humidity Indicator 15% to 95% @ 25°C 1.4%RH Using Single Point Probe
of Humidity with Digital Indicator
Chamber / By Comparison Method,
Environment as per DKD – R-5-7
Chamber♣
(Single point)
2. Humidity Chamber / 15% to 95% @ 30°C 1.75%RH to 2.83%RH Using Humidity Sensors
Environment with Digital Indicator
Chamber♣ (Multi point)
(Multi point) By Comparison Method,
as per DKD- R-5-7
* Measurement Capability is expressed as an uncertainty () at a confidence probability of 95%

$
Only in Permanent Laboratory
♣
Only for Site Calibration
#
The laboratory is also capable for site calibration however, the uncertainty at site depends on the
prevailing actual environmental conditions and master equipment used.
Φ
Laboratory can also calibrate instruments/devices of coarser resolution / least count within the
accredited range using same reference standard/ master equipment under the scope of accreditation.


Sl. Quantity Measured / Instrument Range/Frequency Calibration Measurement Capability ( ) Remarks

Uploaded by

Copyright:

Available Formats

Sl. Quantity Measured / Instrument Range/Frequency Calibration Measurement Capability ( ) Remarks

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sl. Quantity Measured / Instrument Range/Frequency Calibration Measurement Capability ( ) Remarks

Uploaded by

Copyright:

Available Formats

Laboratory Perfect Calibration Centre Pvt. Ltd., No.

84 First Floor, Times Corner,

Sl. Quantity Measured / Range/Frequency *Calibration Measurement Remarks

Vishal Shukla Avijit Das

Sl. Quantity Measured / Range/Frequency *Calibration Measurement Remarks

‘B’ Type Thermocouple 600°C to 1820°C 2.88°C

Vishal Shukla Avijit Das

Sl. Quantity Measured / Range/Frequency *Calibration Measurement Remarks

FLUID FLOW CALIBRATION

1. Air Flow 0.4 to 20 m/s 7.2%rdg Using Anemometer,

Vishal Shukla Avijit Das

Sl. Quantity Measured / Range/Frequency *Calibration Measurement Remarks

I. DIMENSION (BASIC MEASURING INSTRUMENT, GAUGE ETC.)

Vishal Shukla Avijit Das

Sl. Quantity Measured / Range/Frequency *Calibration Measurement Remarks

5. Plunger Type Dial

6. Lever Type Dial

7. Plain Plug Gauge/ Up to 100mm 2.1 µm Using Length Measuring

Vishal Shukla Avijit Das

Sl. Quantity Measured / Range/Frequency *Calibration Measurement Remarks

8. Snap 3 mm to 200mm 1.4 µm Using Slip gauge Set

9. Dial Depth Gauge$

10. Feeler Gauge$ Upto 1.0mm 2.9 µm Using Digital Micrometer

11. Bore Dial Gauge$

12. Dial Thickness

Vishal Shukla Avijit Das

Sl. Quantity Measured / Range/Frequency *Calibration Measurement Remarks

13. Height Gauge$

15. Depth Caliper $

16. Dial Caliper

17. Cylindrical Upto 25mm 2.1 µm Using Length Measuring

Vishal Shukla Avijit Das

Sl. Quantity Measured / Range/Frequency *Calibration Measurement Remarks

18. Cylindrical Upto 100mm 2.1 µm Using Length Measuring

19. Thread Measuring 0.17 mm to 6.35mm 2.1 µm Using Length Measuring

20. Thread Plug gauge$ M2 to M100 3.6 µm Using Length Measuring

M2 to M100 5.6 µm Using FCDM, Thread

21. Taper Thread Ring M2 to M50 5.1 µm Using Length Measuring

22. Thread Ring Gauge$ M3 to M100 3.6 µm Using Length Measuring

Vishal Shukla Avijit Das

Sl. Quantity Measured / Range/Frequency *Calibration Measurement Remarks

23. Taper Thread Plug M2 to M100 7.5 µm Using FCDM, Thread

24. Plain Ring Gauge$ Up to 50mm 3.3 µm Using Length Measuring

26. Coating Thickness 0.01mm to 2mm 1.79 µm Using Standard Foils by

27. Foils$ Up to 250 m 1.2 µm Using Length Measuring

Vishal Shukla Avijit Das

Sl. Quantity Measured / Range/Frequency *Calibration Measurement Remarks

29. Dial Snap Gauge /

30. V - Block$ Using Lever Dial gauge,

32. Comparator Stand$ 300 x 300mm 1.7 µm Using Dial gauge by

33. Straight edge$ Up to 1000mm 6.0 µm Using Electronic Level &

Vishal Shukla Avijit Das

Sl. Quantity Measured / Range/Frequency *Calibration Measurement Remarks

35. LVDT Probe with

36. V- Anvil Micrometer$

37. Mandrel 100 mm dia 13.4 µm Using Bench centre with

38. LVDT Probe with

39. Surface plate♣ 6000 mm X 3000 mm 1.32

40. Height Measuring