Scribd
Upload
82 views2 pages

Tc-Io-1.21 RCP Data Sheet

The Titan I/O Module for RCP consists of an I/O board connected to a backplane and mounting plate. It connects sensors to the Argus control system and produces output control signals. It can be located remotely near sensors and equipment. It interfaces with over a million parts of resolution on a 0-5 volt span to reduce costs.

Uploaded by

fahmi1987
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
82 views2 pages

Tc-Io-1.21 RCP Data Sheet

The Titan I/O Module for RCP consists of an I/O board connected to a backplane and mounting plate. It connects sensors to the Argus control system and produces output control signals. It can be located remotely near sensors and equipment. It interfaces with over a million parts of resolution on a 0-5 volt span to reduce costs.

Uploaded by

fahmi1987
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

TC-IO/RCP

Titan I/O Module for RCP


The Titan I/O (Input/Output) Module for RCP (Relay Control Panels)
consists of a Titan I/O Board (TTN-IO) connected to a standard I/O
Backplane (TTN-IOBP) and a mounting plate (TTN-IOMOD/MP-3) to support
connected Output Relay Boards and for mounting into Argus panel
enclosures. Titan I/O Modules are used to connect sensor instrumentation to
the Argus control system and for producing the output control signals to
operate controlled equipment. www.arguscontrols.com

Applications
Titan I/O modules can be located remotely, close to the connected sensors
and controlled equipment. They are connected to Titan controllers and
powered via a 2-wire I/O Communications Network. With more than a
million parts of resolution over a 0-5 volt span, Titan I/O modules can be
directly interfaced to many sensors that produce signals of only a few
millivolts. Nearly any industrial sensor can be connected, although a few
special types may require external signal conditioning. This helps reduce
instrumentation costs and wiring complexity.
Each output channel is addressable, and can be extensively configured for
most types of output signals including digital (including on/off, pulse width
modulation, pulse period modulation, frequency), analog, and tri-state
floating control. Any combination of Titan Output Relay Boards can be
connected to the supplied backplane to provide the appropriate output
signals.
An optional on-board display unit with operator entry keys is available to
monitor readings and change setting values at the control locations.

Alternatives
I/O Modules are also available in a separate enclosure (TC-IO. A dual I/O Module enclosure is also available (TC-
IO/DUAL).

Features
No-wire module replacement courtesy of the included backplane that accommodates all
‘Plug and Run’
external connections

Analog sensor channels can be switched in the software between AC impedance, DC voltage,
Input Switching
or DC resistance

High Resolution Digital frequency measurement up to 20 kHz

LED Status Indicators Indicate proper wiring and network operation

Expansion Capacity Up to 32 I/O Modules can be operated from a single Titan Controller

Flash Memory Firmware updates can be performed from any operator workstation

Isolation Built-in cross-channel interference protection


Consistent Performance Scan rate does not degrade as a function of system size or load
Low installation and wiring Modules can be located hundreds of meters apart, close to the connected sensors and the
costs equipment they control
Extensive self-diagnostics, error detection, and fault diagnosis for wiring and connected
Error Detection
equipment
EMI Choke Reduces interference generated by devices emitting high frequency ‘noise’

PHONE: 604-538-3531 or 1-888-667-2091 (Canada and the US)  FAX: 604-538-4728  EMAIL: [email protected]
TC-IO/RCP Page 2

Technical Specifications
Dimensions 9" x 9” x 3" (length x width x depth)
Power Consumption 1.5 Watts @ 24VDC (via Titan IO Power Supply module)
Sample Conversion 24-bit A/D, 12 bit D/A
Analog Input Raw Resolution One million parts over 0-5 volts in 5 microvolt steps.

4 Output Relay Board connectors (OP1-OP4) provide:


 up to 8 - 32 discreet digital outputs (depending on the choice of output relay
boards to suit each application)
Output Channels
 or up to 4 tri-state floating (open/close/stop) for reversing motor control
 or up to 4 analog signal (voltage, frequency or current modes)
 or combinations of the above

7 universal analog channels, each 0-5 volts. Software-configurable for direct


Analog Input Channels
connection of DC resistance, DC voltage, or AC impedance at 1 kHz.
2 channels: up to 20 kHz single channel, or up to 10 kHz each for dual channel
Digital Frequency Inputs
measurement
Argus part number CAB- 2C18G/TITAN: West Penn Wire - Aquaseal AQ224, 2-
conductor, 18 gauge cable, suitable for outdoor use (direct burial), indoor trays,
I/O Device Network Cable
moisture & UV resistant. NO SUBSTITUTIONS – USE OF THIS EXACT WIRE IS
CRITICAL FOR PROPER NETWORK COMMUNICATION

Connection Details
I/O Modules are used for Input
and Output connections on the
Titan system. The illustration
shows an I/O module (yellow
background) operating as part of a
typical I/O Device Network for a
Titan Controller.

For installation, please refer to the


custom drawings and wiring
diagrams provided with your
system parts.

Additional Information
For information on available Output Relay Boards please refer to
the Argus Data Sheets for the following parts:
TTN-D1S; TTN-D2; TTN-D4; TTN-D8;
TTN-D8/MUX-3V; TTN-D8/MUX-4X2; TTN-D8/MUX-8X1;
TTN-P1A; TTN-P1T; TTN-P1T/IC
www.arguscontrols.com
PHONE: 604-538-3531 or 1-888-667-2091 (Canada and the US)  FAX: 604-538-4728  EMAIL: [email protected]

Rev: February 2015

You might also like