Programmable Room Thermostat

With RF

Instruction Manual
Model No RT500RF
PRODUCT COMPLIANCE
SALUS Controls Plc hereby declares that the radio equipment type
868Mhz is in compliance with Directives 1999/5/EC, 2014/53/EU,
2006/95/EC, 2004/108/EC, 2011/65/EU, 2009/125/EC and 93/68/
EEC. The full text of the EU declaration of conformity is available at
the following internet address: www.saluslegal.com

SAFETY INFORMATION
These instructions are applicable to the SALUS Controls model stated
on the front cover of this manual only, and must not be used with
any other make or model.

These instructions are intended to apply in the United Kingdom only,

and should be followed along with any other statutory obligations.

This accessory must be fitted by a Competent person, and

installation must comply with the guidance provided in the current
editions of BS7671 (IEE Wiring Regulations) and Part ‘P’ of the
Building Regulations. Failure to comply with the requirements of
these publications could lead to prosecution.

Always isolate the AC Mains supply before opening or removing

the unit from the wall or wall box.

When fitting batteries don’t mix old and new batteries

together. Do not use rechargable batteries.

Please leave these instructions with the end user where they should
be kept in a safe place for future reference.

ErP RATING
This product has been rated as: Class 1, Efficiency 1%

2 RT500RF INSTRUCTION MANUAL

INTRODUCTION
What is a programmable room thermostat?
... an explanation for householders
A programmable room thermostat is both a programmer and a room thermostat.
A programmer allows you to set ‘On’ and ‘Off’ time periods to suit your own lifestyle. A
room thermostat works by sensing the air temperature, switching on the heating when
the air temperature falls below the thermostat setting, and switching it off once this set
temperature has been reached.
So, a programmable room thermostat lets you choose what times you want the heating
to be on, and what temperature it should reach while it is on. It will allow you to select
different temperatures in your home at different times of the day (and days of the week)
to meet your particular needs.
Turning a programmable room thermostat to a higher setting will not make the room heat
up any faster. How quickly the room heats up depends on the design of the heating system,
for example, the size of boiler and radiators.
Neither does the setting affect how quickly the room cools down. Turning a programmable
room thermostat to a lower setting will result in the room being controlled at a lower
temperature, and saves energy.
The way to set and use your programmable room thermostat is to find the lowest
temperature settings that you are comfortable with at the different times you have chosen,
and then leave it alone to do its job. The best way to do this is to set low temperatures first,
say 18°C, and then turn them up by one degree each day until you are comfortable with
the temperatures. You won’t have to adjust the thermostat further. Any adjustments above
these settings will waste energy and cost you more money.
If your heating system is a boiler with radiators, there will usually be only one programmable
room thermostat to control the whole house. But you can have different temperatures in
individual rooms by installing thermostatic radiator valves (TRVs) on individual radiators.
If you don’t have TRVs, you should choose a temperature that is reasonable for the whole
house. If you do have TRVs, you can choose a slightly higher setting to make sure that
even the coldest room is comfortable, then prevent any overheating in other rooms by
adjusting the TRVs.
The time on the programmer must be correct. Some types have to be adjusted in spring
and autumn at the changes between Greenwich Mean Time and British Summer Time.

RT500RF INSTRUCTION MANUAL 3

You may be able to temporarily adjust the heating programme, for example, ‘Override’,
‘Advance’ or ‘Boost’. These are explained in the manufacturer’s instructions.
Programmable room thermostats need a free flow of air to sense the temperature, so they
must not be covered by curtains or blocked by furniture. Nearby electric fires, televisions,
wall or table lamps may prevent the thermostat from working properly.

INTRODUCTION
The RT500RF from SALUS Controls is a stylish and accurate 5/2 or 7 day programmable
electronic thermostat with a large, easy to read Liquid Crystal Display (LCD). This
programmable thermostat has been specifically designed to be used for both Volt Free
and AC heating applications. This programmable thermostat can replace most common
residential thermostats and is designed to be used with electric, gas or oil heating control
systems. Unlike ordinary single unit design thermostats, this is a new type of thermostat
separating the operational functions into two units.
The Receiver is used for wiring connections and heat on/off control. The Control Centre
provides the user interface and temperature sensing / control. The two units are linked
together by a Radio Frequency (RF) signal.
Features
• Volt free switching option
• 5/2 or 7 day programming flexibility
• Built-in start up programming for quick installation
• Frost protection
• Large, easy to read LCD with blue backlight
• Burner on symbol
• Easy to use programming
• User friendly

4 RT500RF INSTRUCTION MANUAL

INSTALLATION
Please read the important safety information at the start of this
manual before you begin to install the device.

The RT500RF Control Centre is easily installed using the Industry

Standard back plate supplied with the unit – this is used purely for
mounting purposes, as no wiring is needed for the Control Centre.
The back plate can be mounted directly to the wall surface.

The ideal position to locate the RT500RF Control Centre is about

1.5m above floor level. It should be mounted in a location where
the thermostat is accessible, reasonably lit and free from extremes
of temperature and draughts. Do not mount the thermostat on
an outside wall, above a radiator or in a location where it may be
subjected to direct sunlight.

To ensure trouble free operation of the Radio Frequency (RF) signal,

always ensure that the programmable thermostat is mounted away
from any possible sources of interference (such as radios, TV sets,
computers, etc.), and is not mounted on or in close proximity to
large metal objects. Installing the RT500RF in enclosed areas such as
cellars and basements is not recommended.

CONNECTING THE RT500RF RECEIVER

NOTE: All electrical installation work should be carried out by a
suitably qualified Electrician or other competent person.

If you are not sure how to install this programmable thermostat

consult either with a qualified electrician, heating engineer or your
boiler / heating system supplier for advice on how to continue.

RT500RF INSTRUCTION MANUAL 5

Salus RT500RF Manual 006.qxp_89 21/10/2015 12:15 Page 6

The RT500RF Receiver should be mounted

in a suitable location that is both accessible
forThethe connection
RT500RF Receiverof mains
should and control
be mounted in a
suitable
wiring, location
and allowsthat is both
good accessible
reception of for
thetheRF
connection
signal. of mainsneeds
The Receiver and control
a 230Vwiring, and
AC mains
allows good reception of the RF signal.
supply to operate, and this should be fused The
Receiver needs
appropriately (13Aa max.).
230V ACThemains supply
Receiver to
should
beoperate,
mountedand this should
in a location where beit willfused
not
appropriately (13A max.). The Receiver should
come into contact
be mounted with water,
in a location wheremoisture
it will not or
condensation.
come into contact with water, moisture or
condensation.
The Receiver On/Off switch is accessible from
theThe
front face of
Receiver the Receiver,
On/Off switch isas shown infrom
accessible this
picture:
the front face of the Receiver, as shown in this
picture:
On the front cover of the Receiver you will see
Onthere
that the front
is thecover of theswitch
On/Off Receiver
and you willLight
two see
that there
Emitting is the On/Off
diodes (LEDs).switch and twoallows
The switch Light
youEmitting
to turndiodes
off the(LEDs). Theifswitch
Receiver allows
necessary to
you to itturn
prevent off the
calling forReceiver
heat. Theif necessary
bottom LED to
prevent it calling for heat. The
(red) will illuminate when the switch is inbottom LED
the(red)
‘On’will illuminate
position andwhen
thethe switch
unit is in the
is receiving
‘On’ position and the unit is receiving power.
power.
The topThe LEDtop LED illuminates
(green) (green) illuminates
when the
when the Receiver
Receiver unit isunit is receiving
receiving a heatcall
a heat call
transmission
transmissionfrom fromthetheControl
Control Centre.
Centre.
TheThewiring
wiringterminals andRF
terminals and RFAddress
Address Code
Code setting
setting DIP DIP switches
switches are located
are located on the on
therear
rear
of of
thethe Receiver,
Receiver, as shown
as shown in this
in this picture:
picture:

RECEIVER
RECEIVERWIRING
WIRING TERMINALS
TERMINALS
TerminalIdentifier
Terminal Identifier Description
Description
1 1 NO
NO Normally Open
Normally Open[N/O]
[N/O]
2 2 COM
COM Linked Live
Linked Live feed
feed(230V
(230VAC
ACheating
heatingapplications only)
applications only)
3 3 L L Live feed (230V AC)
Live feed (230V AC)
4 N Neutral
4 N Neutral

6 RT500RF INSTRUCTION MANUAL

6 RT500RF INSTRUCTION MANUAL
TYPICAL WIRING INSTALLATIONS
a. 230V AC Installation

Notes:
• Receiver unit should have a permanent 230V AC main supply
• Confirm that the Boiler has an external thermostat loop and
is configured for 230V switching
• If the boiler has two terminals for the thermostat, remove the
link from the boiler

b. 24V Installation

Notes:
• Receiver unit should have a permanent 230V AC main supply
• Confirm that the Boiler has an external thermostat loop
and is NOT configured for 230V switching
• If the boiler has two terminals for the thermostat,
remove the link from the boiler

RT500RF INSTRUCTION MANUAL 7

CONTROL CENTRE JUMPER SETTINGS
Changes to the jumper settings should only be made by the Engineer
carrying out the installation or other qualified person.

The installer should select the jumper

positions required if changes need to
be made to the factory default settings.
These jumpers are found on the rear of
the Control Centre.

Jumper Function
Program Jumper for 5-2 (factory default setting) or 7
individual days programming.
Span Movable jumper for selecting temperature span
of ± 0.5°C (factory default setting) or ± 1.0°C
1,2,3,4,5 Removable jumpers for altering the RF address
code when used in conjunction with the
corresponding DIP switch on the Receiver.

NOTE: The Reset button must be pressed after changing jumper positions.

8 RT500RF INSTRUCTION MANUAL

RF ADDRESS CODE SETTING
If there is another unit being used nearby, e.g. in the next house or as part
of a multiple installation, your Receiver may be fault triggered by the other
Control Unit. You can change the RF Address Code to help prevent this
problem.

Each Receiver can only respond to RF transmissions from a Control Centre

that has the same RF address code setting.

Disconnect any AC power to the Receiver, and remove the batteries from the
Control Centre before attempting any adjustment of the RF Address Code
switches and jumpers. If you are not sure how to carry out this operation
correctly, consult either with a qualified electrician or heating engineer.

To adjust the RF address code of the Receiver, simply push up one or more
of the 5 DIP switch levers on the DIP switch bank located on the back of the
receiver (the levers are numbered 1 to 5 from bottom to top, as shown in the
picture below), and then make a note of the setting of each switch:

RT500RF INSTRUCTION MANUAL 9

To adjust the RF address code of the Control Centre, remove one or more of
the jumper caps located on the back of the unit (labelled 1,2,3,4 and 5, and
shown in the picture below) so that the jumper settings match the settings
made on the receiver:

For example, if the DIP switches on the Receiver were set as follows:

1 - ON
2 - OFF
3 - OFF
4 - OFF
5 - ON

Then you would need to remove jumper caps 2, 3 and 4 on the Control
Centre to make sure that they are both set with the same RF address code.
Please make sure that you keep any of the jumper caps you remove in a safe
place, in case you later need to change the RF address setting again.

You must press RESET on the Control Centre after making any changes to
the RF address code settings.

10 RT500RF INSTRUCTION MANUAL

TESTING THE RF TRANSMISSION
It is important to site both the Receiver and Control Centre in locations
where the RF signal cannot be interrupted.
The receiving range between Control Centre and Receiver is approximately
30 metres indoors, however many factors can affect the RF transmission
and shorten the operating distance, e.g. shielding by thick walls, foil back
plasterboard, metal objects such as filing cabinets, general RF interference,
and so on.
The range is generally large enough for most household applications, but
it is advisable to test the RF transmission from the intended Control Centre
location to the Receiver location before fixing the Control Centre to the wall.
To check the RF reception, follow the following steps:

1. Press the UP button on the Control Centre until the set point
temperature is higher than room temperature by a few degrees.
2. Wait for a few seconds. The Burner on (heat call) indicator should
appear on the bottom left of the LCD on the Control Centre.
3. Check the green LED on the receiver unit - it should be lit.
4. Press the DOWN button to adjust the set point temperature to be
lower than room temperature.
5. Wait for a few seconds, and the Burner on (heat call) indicator
should disappear and the green LED should switch off.
6. If at step 3 the green LED is not illuminated, press the RESET button on
the Control centre and try to place the Control Centre closer
to the Receiver.
7. Repeat steps 1 to 5.

If you are unable to get a stable RF connection between the Receiver and
Control Centre, check that the Receiver is both switched on and has a mains
supply (red LED lit). If this isn’t the problem you can also alter the RF address
code by following the ‘RF Address Code Setting’ section of this manual, and
then repeat steps 1 to 5 (note that the RESET button on the Control Centre
should be pressed after altering the address code).

RT500RF INSTRUCTION MANUAL 11

MULTIPLE THERMOSTAT INSTALLATIONS
If you are using more than one RT500RF programmable thermostat
in the same installation, be sure that there is at least a 1 metre gap
between receiver units to avoid crosstalk and other RF interference.

When installing multiple thermostats, you should assign different

RF address codes for each RT500RF by following the instructions in
the ‘RF Address Code Setting’ section of this manual. Each RT500RF
should be introduced to the installation one at a time with all other
Receiver units switched off. Also make sure that the batteries are
removed from all other Control Centres.

Install each unit following the ‘Testing the RF Transmission’ section

above - once you are happy with the operation of one unit you can
install the next.

Once all the RT500RF units have been installed, if one unit then
seems to function abnormally, try changing the RF address code of
that unit’s Control Centre and its corresponding Receiver, making
sure that the new RF address code is different to all others in the
installation.

The control centre sends RF On/Off signals every 10 minutes to

ensure the Receiver is in the correct state. If for some reason the
first RF signal is interrupted you may notice the Control Centre has
stopped or started calling for heat but the Receiver hasn’t switched.
Simply wait 10 minutes until the next RF signal is transmitted and
the receiver unit should then switch correctly.

12 RT500RF INSTRUCTION MANUAL

AFTER INSTALLATION
The following table shows the settings of the RT500RF programmable
thermostat after Power on, or after RESET is pressed:

Function Status After Reset or Power On

Operation Mode Normal mode
Room Temperature 22.0 °C, updated within 5 seconds
°C indicator On
Clock 12:00
AM/PM indicator AM
Day of Week indicator M
Program Default factory setting
Set Point Temperature Default factory setting
Program Number indicator 1
SET indicator Off
PROG indicator Off
Frost Protection indicator Off
Heat indicator Off
Low-Battery Warning indicator Off, updated within 5 seconds
Output Relay Off
After Power on, the thermostat will operate in Normal mode (Normal mode is
when the thermostat is displaying the room temperature):
• The set point temperature is reset to the default setting
• The room temperature display is updated within 5 seconds
• The control process starts
• The programme number is updated to indicate the running program
If the Reset Button is pressed, the RT500RF will behave in the same way as
described above, except that any previously saved user settings stored in the
internal memory will be deleted and overwritten with the default settings, and
all programmable thermostat control settings will be returned to default values.

RT500RF INSTRUCTION MANUAL 13

USER INTERFACE AND CONTROLS
The status and operation of the RT500RF is
clearly shown on the large backlit Liquid Crystal
Display (LCD).
This display allows the user to see at a glance the
current status of the heating system, the current
time and day of the week, as well as a clear
indication of the current room temperature.
There are few user controls for the RT500RF,
making the programmable thermostat very
easy to operate. These controls are shown
below, along with a description of each of their
functions.
USER CONTROL
FUNCTION SUMMARY
Key / Operation Symbol Functions
UP key Increases the selected setting

DOWN key Decreases the selected setting

BACKLIGHT / Manually turns on the LCD backlight

FROST key for 5 seconds, or activates /
deactivates Frost Protection
SELECT key Selects a clock or programme setting

SET key Sets a clock or programme setting

RESET button Resets the programmable thermostat

to default (original factory) settings

14 RT500RF INSTRUCTION MANUAL

OPERATION
The RT500RF is configured and adjusted
by the use of a minimal number of user
controls, and an intuitive user interface.

The backlit Liquid Crystal Display (LCD)

gives a highly visible, easily readable
indication of the programmable thermostat
status.

SETTING THE TIME

Press and hold SET and SELECT when
the RT500RF is in Normal mode for a few
seconds to enter the Clock setting mode.
Release both keys and the display will look
like the image below:

The Time and Day are displayed along with a SET indicator, with all other
indicators cleared from the display. The hour part of the time is flashing to
indicate that it is the currently selected item and is ready to be adjusted.
• Press the UP or DOWN keys to increase or decrease the ‘hour’ setting –
the
selected item will stop flashing while a key is pressed, and will resume
flashing when you release the key.
• Press the SELECT key to select the ‘minutes’ section of the time. Set the
minutes in the same way as the hour by using the UP and DOWN keys.
• Press SELECT again to select the Day, and again change the setting with
the UP and DOWN keys.
• Press the SET key to confirm the new time and day settings. This will store
the changes and return the RT500RF to Normal mode.
The RT500RF Control Centre will also return to Normal mode (and save the

RT500RF INSTRUCTION MANUAL 15

PROGRAMMING THE RT500RF
The RT500RF offers great versatility with its programming options, allowing
the user to programme the unit to operate on a 5/2 or 7 day control cycle.
The programmable thermostat has a default set of Programmes that have
been designed to meet the needs of most users. If these default programmes
are not suitable for your particular situation, reprogramming the RT500RF
with your own settings is a very straightforward operation.

Selection of the default programming mode (5/2 or 7 day) is made by

changing the jumper setting on the rear of the RT500RF Control Unit, as
previously described within the Installation section of this manual.

5/2 DAY MODE

5/2 day mode is the default programming mode for the RT500RF. With this
mode selected, five different sets of time and set point temperatures can be
set for Weekdays or Weekends.

To review or change a programme, press the SET key when the RT500RF is in
Normal mode. This will change the unit status to Programme Setting mode.

The LCD display will display programme number 1 and SET PROG, with all
other indicators cleared. The weekdays will be flashing to indicate they are
the selected item and are ready to be adjusted:

16 RT500RF INSTRUCTION MANUAL

Press the UP or DOWN key to select the programme set for either Weekday
or Weekend to be reviewed or adjusted. Pressing the SET key at any time
when in programming mode will return the RT500RF into Normal mode.

Press the SELECT key to confirm the Weekday or Weekend selection. Once
this is set, the ‘Hour’ will flash to indicate that it is the selected item and is
the next item to be adjusted:

Press the UP or DOWN key to adjust the

hour setting to the desired value, and
confirm your selection by pressing the
SELECT key.

Pressing the SELECT key allows you

to step through each of the items to
be reviewed or adjusted within the
programmes in the following sequence:

Programme Function Sequence

1 Hour Minutes Set point temperature
2 Hour Minutes Set point temperature
3 Hour Minutes Set point temperature
4 Hour Minutes Set point temperature
5 Hour Minutes Set point temperature

…before then allowing you to cycle back to Programme 1. Pressing the SET
key at any time will confirm the setting and return to the programme set
selection.

RT500RF INSTRUCTION MANUAL 17

7 DAY MODE
The RT500RF also offers a 7 day programming mode, which allows you to
programme five different sets of time and set point temperatures for each
day of the week to give a total of 35 separate programme settings.

To review or change a programme, press the SET key when the RT500RF is
in Normal mode. This will change the unit status to Programme Setting
mode.

The LCD display will display programme number 1 and SET PROG, with all
other indicators cleared. The weekdays will be flashing to indicate they are
the selected item and are ready to be adjusted.

Press the UP or DOWN key to change the

display to indicate the single day you
want to programme:

Pressing the SET key at any time when in programming mode will return
the RT500RF into Normal mode. Press the SELECT key to confirm the Day
selection. Once this is set, the ‘Hour’ will flash to indicate that it is the
selected item and is the next item to be adjusted:

18 RT500RF INSTRUCTION MANUAL

Press the UP or DOWN key to adjust the hour setting to the desired value,
and confirm your selection by pressing the SELECT key.

Pressing the SELECT key allows you to step through each of the items to be
reviewed or adjusted within the programmes in the following sequence:

Programme Function Sequence

1 Hour Minutes Set point temperature
2 Hour Minutes Set point temperature
3 Hour Minutes Set point temperature
4 Hour Minutes Set point temperature
5 Hour Minutes Set point temperature

…before then allowing you to cycle back to Programme 1. Pressing the

SET key at any time will confirm the setting and return to the programme
set selection. Each programme for all the other days of the week is set in
exactly the same way – just repeat the steps shown above, after entering
programming mode and selecting the day you want to programme.

Regardless of which programming mode the RT500RF is set for (5/2 or

7 day), not pressing any keys for 15 seconds will automatically save any
programming changes and exit to Normal mode. You can also review or
change programme settings when Frost Protection is enabled.

RT500RF INSTRUCTION MANUAL 19

FROST PROTECTION
To enable the Frost Protection mode, press and hold the BACKLIGHT / FROST
button for three seconds with the RT500RF in Normal mode. Once Frost
Protection is enabled, the set point temperature is automatically set to 5°C
to provide protection from the risk of freezing.

Whenever Frost Protection is activated, the Frost Protection indicator will

flash in the sequence shown below:

While Frost Protection is activated, it will override any programme settings

until the mode is changed. To turn off Frost Protection mode, press and hold
the BACKLIGHT / FROST button for three seconds.

REVIEWING SET POINT TEMPERATURE

You can view the set point temperature at any time by pressing either the
UP or DOWN key.

When any programme is running, the

LCD display will show the programme set
point temperature with the SET indicator
displayed:

20 RT500RF INSTRUCTION MANUAL

 When operating in Frost Protection mode,
the LCD display will show a reading of 5
°C and also display the Frost Protection
indicator:

When operating in Temporary Override

mode, the LCD display will show the
temporary set point temperature:

To exit from the set point review, press any

key except the UP or DOWN keys, or don’t press any keys for approximately
four seconds – either of these actions will return the RT500RF to Normal
mode.

TEMPORARY OVERRIDE
It is possible to temporarily override the current set temperature of the
RT500RF. There are two ways to do this:

• While reviewing set point temperature: Pressing the UP or DOWN key

while reviewing the set point temperature will increase or decrease the
set point temperature in 0.5 °C steps.
• In Normal mode: press and hold either the UP or DOWN key to display
the set point temperature. After two seconds, the RT500RF will enter
Temporary Override mode and allow increase or decrease of the set point
temperature. If the key is released within two seconds then you will only
be able to review the set point temperature.

RT500RF INSTRUCTION MANUAL 21

Once in Temporary Override mode, the clock and day are displayed, along
with the SET indicator; all other indicators are cleared from the display. The
set point temperature will flash to indicate that it can be changed:

Pressing the UP or DOWN key will increase or decrease the set point
temperature in 0.5 °C steps - the set point temperature can be adjusted
within a set range or 10 °C to 35 °C.

You can press SET at any time to confirm the new Temporary Override
setting and return to Normal mode, or press no keys at all and wait
approximately four seconds.

Temporary Override mode remains active until the clock or programme

settings are adjusted, Frost Protection is activated or the next programme
time / temperature set point is reached.

22 RT500RF INSTRUCTION MANUAL

OTHER FUNCTIONS AND CONTROLS
Backlight
The backlight of the RT500RF is switched on automatically whenever any of
the keys are pressed. The backlight will remain illuminated for approximately
5 seconds after the last key press, except if you are changing settings within
the Clock, Programme or Temporary Override modes – in this case, the
backlight will remain illuminated throughout the setting change process.
The backlight will not illuminate if the RT500RF battery is low.
Battery Status
The RT500RF checks the battery voltage frequently during normal
operation. If the battery voltage is sensed as being low (this is normally
when the battery voltage falls to a level of around 2.6V), the low battery
indicator will be displayed on the screen.

Although the programmable thermostat will continue to operate normally

at this stage, you should replace the batteries as soon as possible to prevent
any possible operating problems.
Reset Button
The Reset Button is provided as a way to restore the programmable
thermostat to its default factory settings. Pressing this button will delete
any previously entered settings.
Sleep Mode
By pressing both the UP and DOWN keys together, the RT500RF will enter
SLEEP mode. In this mode, all the RT500RF functions will be paused to save
battery power, with the exception of the clock which will continue to run
in the background.
While in SLEEP mode:
• The LCD display will be blank.
• All output from the Control Unit will be turned off immediately.
Press any key to wake up the RT500RF and cancel SLEEP mode.

RT500RF INSTRUCTION MANUAL 23

ENERGY TIP
One way to set and use your room thermostat is to find the lowest
temperature setting that you are comfortable with, and then leave it set
at this temperature. You can do this by setting the room thermostat to a
low temperature, (for example 17 °C) and then increasing the setting by
one degree each day until you are comfortable with the room temperature
- you won’t have to adjust the thermostat further, as adjustment above this
setting will waste energy - a 1 °C increase in temperature is equal to 3% of
your heating costs.

MAINTENANCE
The RT500RF programmable thermostat requires no special maintenance.
Periodically, the outer casing can be wiped clean using a dry cloth (please
DO NOT use solvents, polishes, detergents or abrasive cleaners, as these can
damage the thermostat).
There are no user serviceable parts within the unit; any servicing or repairs
should only be carried out by SALUS Controls or their appointed agents.
Should the RT500RF programmable thermostat fail to function correctly,
check:
• The batteries are the correct type, fitted correctly and are not exhausted
- fit new batteries if in doubt.
• Heating system is switched on.
• The RT500RF Receiver is switched on.
• If the RT500RF is still not functioning correctly, press the Reset Button.
WARRANTY
SALUS Controls warrants that this product will be free from any defect
in materials or workmanship, and shall perform in accordance with
its specification, for a period of two years from the date of purchase.
SALUS Controls sole liability for breach of this warranty will be (at its option)
to repair or replace the defective product.

24 RT500RF INSTRUCTION MANUAL

PRODUCT SPECIFICATION
Model: RT500RF
Type: Electronic programmable thermostat, designed
for Volt Free and AC heating applications.
Frequency 868 MHz
Programming
Programming Modes: User selectable for 5/2 or 7 day option
Number of Programmes: Five (5) user programmes plus factory
default programme.
Override Facility: User selectable programme override facility.

Default Programmes
Programme Output Weekday Weekend
1 ON 6:00 AM 6:00 AM
TEMP 21 ºC 21 ºC
2 ON 8:00 AM 8:00 AM
TEMP 14 ºC 21 ºC
3 ON 4:00 PM 4:00 PM
TEMP 21 ºC 21 ºC
4 ON 6:00 PM 6:00 PM
TEMP 21 ºC 21 ºC
5 ON 10:00 PM 10:00 PM
TEMP 14 ºC 14 ºC

Temperature
Scale: Celsius
Range: 5 ºC to 35 ºC
Resolution: 0.5 ºC
Tolerance: Less than ± 0.5 ºC at 25 ºC
Display Range: 5.0 ºC to 45.0 ºC
Display Resolution: 0.5 ºC

RT500RF INSTRUCTION MANUAL 25

Clock
Accuracy: ± 1 minute per month
Display: 12 hour

Frost Protection
Setting: 5 ºC
Setpoint Temperature Range: 5 ºC to 35 ºC
Measured Air Temperature Range: 5 ºC to 45 ºC (Displayed on LCD)
If room temp is higher than 45C,will show HI on
the LCD, if less than 5C will show LO on the LCD

Control Centre
Power Source: 2 x AA alkaline batteries
(don’t use rechargeable batteries)

Receiver
Power Source: 230V AC / 50Hz

Switch Rating
Switching Voltage: 0 - 230V AC / 50Hz
Switching Current: 16A resistive, 5A inductive
Protection Rating: IP30

Environment
Operating Temperature: 0 ºC to + 40 ºC
Storage Temperature: - 10 ºC to + 60 ºC

26 RT500RF INSTRUCTION MANUAL

RT500RF Warranty
SALUS Controls warrants that this product will be free from any defect
in materials or workmanship, and shall perform in accordance with
its specification, for a period of two years from the date of purchase.
SALUS Controls sole liability for breach of this warranty will be (at its option)
to repair or replace the defective product.

Customer Name: ....................................................

Customer Address: ................................................
...............................................................................
Post Code: ..................... Tel No: ............................
Email: .....................................................................
Engineers Company: ..............................................
Tel No: ...................................................................
Email: ....................................................................
Intallation Date: .....................................................
Engineers Name: ....................................................
Engineers Signature: ..............................................

RT500RF INSTRUCTION MANUAL 27

 www.salus-tech.com
Sales: Email: [email protected] Tel: 01226 323961
Technical: Email: [email protected] Tel: 01226 323961

SALUS Controls plc, SALUS House, Dodworth Business Park South,

Whinby Road, Dodworth, Barnsley S75 3SP