Scribd Logo
Upload

Welcome to Scribd!

  • 695 views

    Profibus Yokogawa Master Siemens Slave

    Uploaded by

    Carlos Magno Cardoso Cantagalli
    This document provides instructions for setting up a Profibus connection between a Yokogawa Centum ALP121 (master) and a Siemens S7 417-4 (slave) DP port. It describes configuring the Siemens Simatic Manager software to set the slave address and operating mode. It also describes adding virtual I/O modules in both the Siemens and Yokogawa systems to define the send and receive address ranges. Finally, it notes important settings in the Yokogawa Sycon software like importing the GSD file and ensuring "Enable DPV1" is unchecked.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Profibus Yokogawa Master Siemens Slave

    Uploaded by

    Carlos Magno Cardoso Cantagalli
    695 views6 pages
    This document provides instructions for setting up a Profibus connection between a Yokogawa Centum ALP121 (master) and a Siemens S7 417-4 (slave) DP port. It describes configuring the Siemens Simatic Manager software to set the slave address and operating mode. It also describes adding virtual I/O modules in both the Siemens and Yokogawa systems to define the send and receive address ranges. Finally, it notes important settings in the Yokogawa Sycon software like importing the GSD file and ensuring "Enable DPV1" is unchecked.

    Original Description:

    Configuration Profibus Yokogawa Master Siemens Slave

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides instructions for setting up a Profibus connection between a Yokogawa Centum ALP121 (master) and a Siemens S7 417-4 (slave) DP port. It describes configuring the Siemens Simatic Manager software to set the slave address and operating mode. It also describes adding virtual I/O modules in both the Siemens and Yokogawa systems to define the send and receive address ranges. Finally, it notes important settings in the Yokogawa Sycon software like importing the GSD file and ensuring "Enable DPV1" is unchecked.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    695 views6 pages

    Profibus Yokogawa Master Siemens Slave

    Uploaded by

    Carlos Magno Cardoso Cantagalli
    This document provides instructions for setting up a Profibus connection between a Yokogawa Centum ALP121 (master) and a Siemens S7 417-4 (slave) DP port. It describes configuring the Siemens Simatic Manager software to set the slave address and operating mode. It also describes adding virtual I/O modules in both the Siemens and Yokogawa systems to define the send and receive address ranges. Finally, it notes important settings in the Yokogawa Sycon software like importing the GSD file and ensuring "Enable DPV1" is unchecked.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 6

    Profibus Setup Yokogawa Centum ALP121 (Master) to Siemens S7 417-4 (Slave) DP Port X2

    Siemens Simatic Manager- Open “DP”Properties in Hardware Config

    Set Address to Desired Value

    Page |1
    Profibus Setup Yokogawa Centum ALP121 (Master) to Siemens S7 417-4 (Slave) DP Port X2

    In “Operating Mode” - Select “DP Slave” and “DPV1”

    Add new Virtual IO for Communication Outside of the Physically Installed IO


    Address Range. DCS and AS will Write and Read to and from the assigned area to the
    AS IO image (next slides how to). There can be up to 32 R/W blocks.

    Page |2
    Profibus Setup Yokogawa Centum ALP121 (Master) to Siemens S7 417-4 (Slave) DP Port X2

    Setup “Send” address range from Siemens Slave to Yokogawa DCS Master (Ensure
    all settings are identical at Yokogawa end before downloading and connecting
    Profibus cable)

    Setup “Receive” address range from Yokogawa DCS Master to Siemens Slave
    (Ensure all settings are identical at Yokogawa end before downloading and
    connecting Profibus cable)

    WARNING: A misconfiguration at either end will cause the PLC to STOP when
    connecting the Profibus cable
    Yokogawa Master Setup

    Page |3
    Profibus Setup Yokogawa Centum ALP121 (Master) to Siemens S7 417-4 (Slave) DP Port X2

    In Sycon – Import S7 GSD file for relevant processor type and drag onto the profibus
    connection of the ALP121 module.

    Add virtual modules of choice (must align with Simatic configuration). Input in
    Yokogawa must be matched with Output on Siemens.

    Page |4
    Profibus Setup Yokogawa Centum ALP121 (Master) to Siemens S7 417-4 (Slave) DP Port X2

    Setup as above

    Ensure “Enable DPV1” is Unchecked. Having this checked caused the PLC to
    STOP.

    Page |5
    Profibus Setup Yokogawa Centum ALP121 (Master) to Siemens S7 417-4 (Slave) DP Port X2

    Setup WW table. Refer to Yokogawa Centum VP manual “Communication with


    PROFIBUS Systems” IM 33K03P10-50E.

    IMPORTANT DISCLAIMER
    This document is only intended as an informational guideline as individual applications and equipment employed may vary. The authors of this document cannot be held liable for any damage or loss caused or suffered.

    Page |6

    You might also like