40 TestBank06

Chapter 6: FORCE AND MOTION – II
1. A brick slides on a horizontal surface. Which of the following will increase the magnitude of
the frictional force on it?
A. Putting a second brick on top
B. Decreasing the surface area of contact
C. Increasing the surface area of contact
D. Decreasing the mass of the brick
E. None of the above
ans: A
2. The coefficient of kinetic friction:

A. is in the direction of the frictional force
B. is in the direction of the normal force
C. is the ratio of force to area
D. can have units of newtons
E. is none of the above
ans: E
3. When the brakes of an automobile are applied, the road exerts the greatest retarding force:
A. while the wheels are sliding
B. just before the wheels start to slide
C. when the automobile is going fastest
D. when the acceleration is least
E. at the instant when the speed begins to change
ans: B
4. A forward horizontal force of 12 N is used to pull a 240-N crate at constant velocity across a
horizontal floor. The coefficient of friction is:
A. 0.5
B. 0.05
C. 2
D. 0.2
E. 20
ans: B
5. The speed of a 4.0-N hockey puck, sliding across a level ice surface, decreases at the rate of
0.61 m/s2 . The coefficient of kinetic friction between the puck and ice is:
A. 0.062
B. 0.41
C. 0.62
D. 1.2
E. 9.8
ans: A
66 Chapter 6: FORCE AND MOTION – II

6. A crate rests on a horizontal surface and a woman pulls on it with a 10-N force. No matter
what the orientation of the force, the crate does not move. Rank the situations shown below
according to the magnitude of the frictional force of the surface on the crate, least to greatest.
....
10 N
......
. ..
.
.
10 N
.
.
. .
.. ...
10 N .
...
...................... ...
.
........
. . . ................................. . . . . . . . . . . ................................ . . . . . . . . . . ......................... . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ......
1 2 3
A. 1, 2, 3
B. 2, 1, 3
C. 2, 3, 1
D. 1, 3, 2
E. 3, 2, 1
ans: E
7. A crate with a weight of 50 N rests on a horizontal surface. A person pulls horizontally on it

with a force of 10 N and it does not move. To start it moving, a second person pulls vertically
upward on the crate. If the coefficient of static friction is 0.4, what is the smallest vertical force
for which the crate moves?
....
.
..........
.
.
.
.
10 N
............................
.
. . . . ......................................... . . . . . . . . .
. . . . . . . . . . . . . . . . . .
A. 4N
B. 10 N
C. 14 N
D. 25 N
E. 35 N
ans: D
8. A 40-N crate rests on a rough horizontal floor. A 12-N horizontal force is then applied to it. If
the coefficients of friction are µs = 0.5 and µk = 0.4, the magnitude of the frictional force on
the crate is:
A. 8 N
B. 12 N
C. 16 N
D. 20 N
E. 40 N
ans: B
Chapter 6: FORCE AND MOTION – II 67

9. A 24-N horizontal force is applied to a 40-N block initially at rest on a rough horizontal surface.
If the coefficients of friction are µs = 0.5 and µk = 0.4, the magnitude of the frictional force on
the block is:
A. 8 N
B. 12 N
C. 16 N
D. 20 N
E. 400 N
ans: C
10. A horizontal shove of at least 200 N is required to start moving a 800-N crate initially at rest
on a horizontal floor. The coefficient of static friction is:
A. 0.25
B. 0.125
C. 0.50
D. 4.00
E. none of these
ans: A
11. A force Ḟ (larger than the largest possible force of static friction) is applied to the left to an
object moving to the right on a horizontal surface. Then:
A. the object must be moving at constant speed
B. Ḟ and the friction force act in opposite directions
C. the object must be slowing down
D. the object must be speeding up
E. the object must come to rest and remain at rest
ans: C
12. A bureau rests on a rough horizontal surface (µs = 0.50, µk = 0.40). A constant horizontal
force, just sufficient to start the bureau in motion, is then applied. The acceleration of the
bureau is:
A. 0
B. 0.98 m/s2
C. 3.3 m/s2
D. 4.5 m/s2
E. 8.9 m/s2
ans: B
13. A car is traveling at 15 m/s on a horizontal road. The brakes are applied and the car skids to
a stop in 4.0 s. The coefficient of kinetic friction between the tires and road is:
A. 0.38
B. 0.69
C. 0.76
D. 0.92
E. 1.11
ans: A

14. A boy pulls a wooden box along a rough horizontal floor at constant speed by means of a force
Ṗ as shown. In the diagram f is the magnitude of the force of friction, N is the magnitude of
the normal force, and Fg is the magnitude of the force of gravity. Which of the following must
be true?
....
......
. ...N
.
.
.
.
.
.
.
Ḟg : force of gravity
.
f˙: frictional force
f ... .. . ............................ ..
P Ṅ : normal force
... .... ... .... ..... ... ... ...
. . . . . . . . . . . . .. . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . .. .. .. . . . . . . . . . . . . .
..
.. .
......
..
...
. g F
A. P = f and N = Fg
B. P = f and N > Fg
C. P > f and N < Fg
D. P > f and N = Fg
E. none of these
ans: A
15. A boy pulls a wooden box along a rough horizontal floor at constant speed by means of a force
Ṗ as shown. In the diagram f is the magnitude of the force of friction, N is the magnitude of
the normal force, and Fg is the magnitude of the force of gravity. Which of the following must
be true?
....
...... N
. ...
.
.
.
. .....
. .... P Ḟg : force of gravity
. .
.
.
θ f˙: frictional force
f . .. .
Ṅ : normal force
... ... .... .... ... ... ........
. . . . . . . . . . . . .. . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . .. .. .. . . . . . . . . . . . . .
.
.
.
.
.
.. .
.....
..
..
.. g
F
A. P = f and N = Fg
B. P = f and N > Fg
C. P > f and N < Fg
D. P > f and N = Fg
E. none of these
ans: C

16. A 400-N block is dragged along a horizontal surface by an applied force Ḟ as shown. The coef-
ficient of kinetic friction is µk = 0.4 and the block moves at constant velocity. The magnitude
of Ḟ is:
.. .
. ....
. F
.
.
.
.
(3/5)F
.
.
.
(4/5)F
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A. 100 N
B. 150 N
C. 200 N
D. 290 N
E. 400 Nb
ans: B
17. A block of mass m is pulled at constant velocity along a rough horizontal floor by an applied
force Ṫ as shown. The magnitude of the frictional force is:
....
..
. .. T
.
.
.
.
.
. ..
. . ....
. . θ
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A. T cos θ
B. T sin θ
C. zero
D. mg
E. mg cos θ
ans: A

18. A block of mass m is pulled along a rough horizontal floor by an applied force Ṫ as shown.
The vertical component of the force exerted on the block by the floor is:
.
...
..
. .. T
.
.
.
.
.
. ..
. . ....
. . θ
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A. mg
B. mg − T cos θ
C. mg + T cos θ
D. mg − T sin θ
E. mg + T sin θ
ans: D
19. A 12-kg crate rests on a horizontal surface and a boy pulls on it with a force that is 30◦ below
the horizontal. If the coefficient of static friction is 0.40, the minimum magnitude force he
needs to start the crate moving is:
A. 44 N
B. 47 N
C. 54 N
D. 56 N
E. 71 N
ans: E
20. A crate resting on a rough horizontal floor is to be moved horizontally. The coefficient of static
friction is 0.40. To start the crate moving with the weakest possible applied force, in what
direction should the force be applied?
A. Horizontal
B. 24◦ below the horizontal
C. 22◦ above the horizontal
D. 24◦ above the horizontal
E. 66◦ below the horizontal
ans: C
21. A 50-N force is applied to a crate on a horizontal rough floor, causing it to move horizontally.
If the coefficient of kinetic friction is 0.50, in what direction should the force be applied to
obtain the greatest acceleration?
A. Horizontal
B. 60◦ above the horizontal
C. 30◦ above the horizontal
D. 27◦ above the horizontal
E. 30◦ below the horizontal
ans: D

22. A professor holds an eraser against a vertical chalkboard by pushing horizontally on it. He
pushes with a force that is much greater than is required to hold the eraser. The force of
friction exerted by the board on the eraser increases if he:
A. pushes with slightly greater force
B. pushes with slightly less force
C. stops pushing
D. pushes so his force is slightly downward but has the same magnitude
E. pushes so his force is slightly upward but has the same magnitude
ans: D
23. A horizontal force of 12 N pushes a 0.5-kg book against a vertical wall. The book is initially at
rest. If the coefficients of friction are µs = 0.6 and µk = 0.8 which of the following is true?
A. The magnitude of the frictional force is 4.9N
B. The magnitude of the frictional force is 7.2N
C. The normal force is 4.9N
D. The book will start moving and accelerate
E. If started moving downward, the book will decelerate
ans: A
24. A horizontal force of 5.0 N pushes a 0.50-kg book against a vertical wall. The book is initially
at rest. If the coefficients of friction are µs = 0.6 and µk = 0.80, the magnitude of the frictional
force is:
A. 0
B. 4.9N
C. 3.0N
D. 5.0N
E. 4.0N
ans: E
25. A horizontal force of 12 N pushes a 0.50-kg book against a vertical wall. The book is initially
at rest. If µs = 0.6 and µk = 0.80, the acceleration of the book in m/s2 is:
A. 0
B. 9.4 m/s2
C. 9.8 m/s2
D. 14.4 m/s2
E. 19.2 m/s2
ans: A
26. A horizontal force of 5.0 N pushes a 0.50-kg block against a vertical wall. The block is initially
at rest. If µs = 0.60 and µk = 0.80, the acceleration of the block in m/s2 is:
A. 0
B. 1.8
C. 6.0
D. 8.0
E. 9.8
ans: B

27. A heavy wooden block is dragged by a force Ḟ along a rough steel plate, as shown below for
two possible situations. The magnitude of Ḟ is the same for the two situations. The magnitude
of the frictional force in (ii), as compared with that in (i) is:
. . ˙
.
. . . F
. . . . .. .
. .... ..
.. .. .
. . .. . .
. ... .. .
.... .. ..
..
.. .. .. ..
. ..
.... .. . .
......... .. ..
. .. .
. ˙
. ....
... .. . .
. ..
.. .. ..
................ .... ..... ..
.. .. .. ... .. .. . .. .. .. . . .. ... .. .. . .. .. .. . .. .. .. . .. .. . . .
F . ...
... . .
. .
. . .. .. .. .. .. .. .. .. . .. .. .. . .. .. .. .. .. .. .. .. . . . . . . .. .. .. . .
...... .
.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(i) (ii)
A. the same
B. greater
C. less
D. less for some angles and greater for others
E. can be less or greater, depending on the magnitude of the applied force.
ans: C
28. A block is first placed on its long side and then on its short side on the same inclined plane, as
shown. The block slides down the plane on its short side but remains at rest on its long side.
A possible explanation is:
. .
.
. . .
.. .. .
. .. ... .
. . ........ ..
.. . .. . . ...
. .. ... ...
....... .. .. ...... .
..
. .. .. .. ..
... . ..
m .
. .
....
....
m . . .. . . .
.. ...... .
..
.. .. . . .
......... .
. .....
.. .. .... ... . . .. . . .
.......... . ..
. . . ...
.. ... . .
...... .. . ..
. ... . .
.. .......... .. ... . ..
. ...
....... .......... ..
. . . . . . ..
.
............... . . v
θ ........................................................... θ ...... ...
.....
.... .
.
.. . .
. . ... .
.. . . . . . ....
... . . ...
... ... . . ...... .
.... ..
. .
(ii) (ii)
A. the short side is smoother

B. the frictional force is less because the contact area is less
C. the center of gravity is higher in the second case
D. the normal force is less in the second case
E. the force of gravity is more nearly down the plane in the second case
ans: A
29. A box rests on a rough board 10 meters long. When one end of the board is slowly raised to a
height of 6 meters above the other end, the box begins to slide. The coefficient of static friction
is:
A. 0.8
B. 0.25
C. 0.4
D. 0.6
E. 0.75
ans: E

30. A block is placed on a rough wooden plane. It is found that when the plane is tilted 30 ◦ to
the horizontal, the block will slide down at constant speed. The coefficient of kinetic friction
of the block with the plane is:
A. 0.500
B. 0.577
C. 1.73
D. 0.866
E. 4.90
ans: B
31. A crate is sliding down an incline that is 35◦ above the horizontal. If the coefficient of kinetic
friction is 0.40, the acceleration of the crate is:
A. 0
B. 2.4 m/s2
C. 5.8 m/s2
D. 8.8 m/s2
E. 10.3 m/s2
ans: B
32. A 5.0-kg crate is resting on a horizontal plank. The coefficient of static friction is 0.50 and the
coefficient of kinetic friction is 0.40. After one end of the plank is raised so the plank makes
an angle of 25◦ with the horizontal, the force of friction is:
A. 0
B. 18 N
C. 21 N
D. 22 N
E. 44 N
ans: C
33. A 5.0-kg crate is resting on a horizontal plank. The coefficient of static friction is 0.50 and the
coefficient of kinetic friction is 0.40. After one end of the plank is raised so the plank makes
an angle of 30◦ with the horizontal, the force of friction is:
A. 0
B. 18 N
C. 21 N
D. 22 N
E. 44 N
ans: B

34. A 5.0-kg crate is on an incline that makes an angle of 30◦ with the horizontal. If the coefficient
of static friction is 0.50, the minimum force that can be applied parallel to the plane to hold
the crate at rest is:
A. 0
B. 3.3N
C. 30 N
D. 46 N
E. 55 N
ans: B
35. A 5.0-kg crate is on an incline that makes an angle of 30◦ with the horizontal. If the coefficient
of static friction is 0.5, the maximum force that can be applied parallel to the plane without
moving the crate is:
A. 0
B. 3.3N
C. 30 N
D. 46 N
E. 55 N
ans: D
36. Block A, with mass mA, is initially at rest on a horizontal floor. Block B, with mass mB, is
initially at rest on the horizontal top surface of A. The coefficient of static friction between the
two blocks is µs. Block A is pulled with a horizontal force. It begins to slide out from under
B if the force is greater than:
A. mAg
B. mB g
C. µsmAg
D. µsmBg
E. µs(mA + mB )g
ans: E
37. The system shown remains at rest. Each block weighs 20 N. The force of friction on the upper
block is:
.. .
...
. .
. .
..
...
.
..
.. W = 20 N
.. . .
.
.. . .. . .
.. ..
..
. .. . .
. ..
. .
. ...
.
..
..
.. ..
..
.. a=3m
... ... . ....... .......
. . . .. .
. . .. . .
.. . . .. ..... .
. ...
.
b=4m
. . ..
..
W .. .
...
. . ..
.
. .. . a W
. . .. . .
.. ....... .. .
. ... . . b .. . .

. .. . .
. .. . . .
. .. . .
.. . . ..
.. . ..
.. .. .. .
.. .. . .
. .. . .

. .. . .

. .. .. . . .
... .. .. .. .

. .. . .
.. .. . .

.. .. . .
.. . . .
.. . .

. ..
.. . .

.. .

.. . .

.

38. Block A, with a mass of 50 kg, rests on a horizontal table top. The coefficient of static friction
is 0.40. A horizontal string is attached to A and passes over a massless, frictionless pulley as
shown. The smallest mass mB of block B, attached to the dangling end, that will start A
moving when it is attached to the other end of the string is:
... . .
....
..•. pulley
..
A .
... ...
.
.. .
. ...
. . . . . . . . . . . . . . . . . . .. .. . .....
.. .. ..
.... .
... ...
............
.. ..
.
... ... ... .. .... .... .. .. ..

... ... ... .... . . . . .... .... .... ...... ...... ....... ....... ..... ..... .......
. . . . . . . . . . . ... . ........
..
.........
.. .
.......
. .
.....
B
. ..
....
. ....
....
. ....
...
....
...
.....
...
...
A. 20 kg
B. 30 kg
C. 40 kg
D. 50 kg
E. 70 kg
ans: A
39. Block A, with a mass of 10 kg, rests on a 35◦ incline. The coefficient of static friction is 0.40.
An attached string is parallel to the incline and passes over a massless, frictionless pulley at
the top. The largest mass mB of block B, attached to the dangling end, for which A begins to
slide down the incline is:
..
.. ...
. . ... .
. .
.
. .. . .
..
. .. .. ..
.
....
. .
. . ..
.
. . ..
.. . .
..
. . . .. . .
.. ..... .. .
. . . .. . .
. . . .. . .. .........
B
. .. . . .
. . .. .
....... .. . . .. .
. .. . ..
. . ..
....
. . .. . .
. . . . ..

. . .. . .

. . .. . .

0
1
2
3
. .. . .
.. . . . .
... ... .. ..
.. ... . ..
.. .. . .

4
5
6
.. ... . . .
. .. . .
.. .. . .
...
. . .
.. . ..

7
. .. . .
.. .. . .

8
9
0
. .. . .

1
2
.. .. . .
.. . . .
.. . .

3
4
5
.. . .

6
7
8
9
.. . .
.. . .
. . .
A. 2.5 kg
B. 3.5 kg
C. 5.9 kg
D. 9.0 kg
E. 10.5 kg
ans: A

0
40. Block A, with a mass of 10 kg, rests on a 35◦ incline. The coefficient of static friction is 0.40.
An attached string is parallel to the incline and passes over a massless, frictionless pulley at
the top. The largest mass mB, attached to the dangling end, for which A remains at rest is:
.. .
. . ..
..
. . ..
..
... ...
..
. .. .
.
..
...
. .. . .. ...... ...
. .... . . .
. . ....
.. . .. .
. . . .. . .
.. ....... ..
. . . .. . .
.
. . . .. ....... B
. .... .
... ....... .. .
.... . ... .. .
..
. . ..
. . .. .
. . . ..
. . .. . .
. .. . ... . .
.

1
..
. .
..
..
.
.. ..... . .
A
B
.
....

2
. .. . .

3
4
5
6
. ..
.. . . .. .
.. . ..
. ...
...

7
. . . .

8
9
13 Chapter 6: FORCE AND MOTION
.
– II
.. . .
0
. .. . . .

1
2
.. .. . .
...
. . .
...

3
4
.. . ..

5
6
. .. . .

7
8
.. .. . .
... . . .
.. . .
.. . .
. ..
.. . .
.. . .
.. . .
.. . .
. . .

9
A. 2.5 kg

0
B. 3.5 kg

1
C. 5.9 kg

2
D. 9.0 kg

3
E. 10.5 kg

4
ans: D

5
.
.
..
.. .
41. Block A, with a mass of 10 kg, rests on a 30◦ incline. The coefficient of kinetic friction is 0.20.

6
The attached string is parallel to the incline and passes over a massless, frictionless pulley at

7
the top. Block B, with a mass of 8.0 kg, is attached to the dangling end of the string. The

8
acceleration of B is:
. ... .
.. . ...
.. . . .
.. ...
.
.
.
. . . ..
...
... . .. .
..
. .. .
. . . .. .......
. .. .
. .. . .
. .... ..
. . . ..
. . .. . .
. . .. . .
. . .. . .
. . . . ..
. . .. . .
. . .. . .
..
. . . ..
. .. . .
. .. . .
.. .. . .
. .. . .
. ... ...
.. . ..
. .. . .
. ...
.. .. . .
. .. . .
. .. . .
.. ..... ...
. .. . .
. .. . .
. .. . .
.. .. . .
.. .. . .
. .. . .
.. .. . .
. .. . .
. .. . .
.. .. . .
. .. . .
. .. . .
.. . . . .
. .. . .
.. . .
.. . .
.. . .
.. . .
.. . .
.. . .
.. . .
.. . .
.. . .
.. . .
. ..
. . .

9
A. 0.69 m/s2 , up the plane
B. 0.69 m/s2 , down the plane
C. 2.6 m/s2 , up the plane
D. 2.6 m/s2 , down the plane
E. 0
ans: B

0
42. Block A, with a mass of 10 kg, rests on a 30◦ incline. The coefficient of kinetic friction is 0.20.
The attached string is parallel to the incline and passes over a massless, frictionless pulley at
the top. Block B, with a mass of 3.0 kg, is attached to the dangling end of the string. The
acceleration of B is:
.
.. ...
..
. .. .. ..
. . .. .
...
...
.
.
. .
. .. . .
..
.
... . . ..
.
.. . . . . .
. . .
.
. . . .
..
.
. . . .. . .
. . . .. .......
.
. .. ..
. .. . .
. .... ..
. . . ..
. . .. . .
. . . ..
...
. . .. . .
. . . . ..
. . .. . .

1
. . .. . .

2
. ... . .

3
4
5
6
7
. .. . .
.. . ..
. .... .. .
.. . .
.. .. ..
. ...
...
. . . .
. .. . .

8
. .. . .
.. .. . .
.. .. . .
.. .. . .
.. .. . .
.. .. . .
.. . ..

9
0
.. .. . .

1
2
. .. . .
. .. . .
.. . ..
.. . . . .

3
. .. . .

4
5
6
7
.. . .
.. . .
.. . .
.. . .
.. . .
. ..
.. . .
. . .
. ..
A. 0.20 m/s2 , up
B. 0.20 m/s2 , down
C. 2.8 m/s2 , up
D. 2.8 m/s2 , down
E. 0
ans: A
43. A 1000-kg airplane moves in straight flight at constant speed. The force of air friction is 1800 N.
The net force on the plane is:
A. zero
B. 11800 N
C. 1800 N
D. 9800 N
E. none of these
ans: A
44. Why do raindrops fall with constant speed during the later stages of their descent?
A. The gravitational force is the same for all drops
B. Air resistance just balances the force of gravity
C. The drops all fall from the same height
D. The force of gravity is negligible for objects as small as raindrops
E. Gravity cannot increase the speed of a falling object to more than 9.8 m/s
ans: B
45. A ball is thrown downward from the edge of a cliff with an initial speed that is three times the
terminal speed. Initially its acceleration is
A. upward and greater than g
B. upward and less than g
C. downward and greater than g
D. downward and less than g
E. downward and equal to g
ans: A

8
46. A ball is thrown upward into the air with a speed that is greater than terminal speed. On the
way up it slows down and, after its speed equals the terminal speed but before it gets to the
top of its trajectory:
A. its speed is constant
B. it continues to slow down
C. it speeds up
D. its motion becomes jerky
E. none of the above
ans: B
47. A ball is thrown upward into the air with a speed that is greater than terminal speed. It lands
at the place where it was thrown. During its flight the force of air resistance is the greatest:
A. just after it is thrown
B. halfway up
C. at the top of its trajectory
D. halfway down
E. just before it lands.
ans: A
48. Uniform circular motion is the direct consequence of:

A. Newton’s third law
B. a force that is always tangent to the path
C. an acceleration tangent to the path
D. a force of constant magnitude that is always directed away from the same fixed point
E. a force of constant magnitude that is always directed toward the same fixed point
ans: E
49. An object moving in a circle at constant speed:

A. must have only one force acting on it
B. is not accelerating
C. is held to its path by centrifugal force
D. has an acceleration of constant magnitude
E. has an acceleration that is tangent to the circle
ans: D
50. An object of mass m and another object of mass 2m are each forced to move along a circle of
radius 1.0 m at a constant speed of 1.0 m/s. The magnitudes of their accelerations are:
A. equal √
B. in the ratio of 2 : 1
C. in the ratio of 2 : 1
D. in the ratio of 4 : 1
E. zero
ans: A

9
51. The magnitude of the force required to cause a 0.04-kg object to move at 0.6 m/s in a circle of
radius 1.0 m is:
A. 2.4 × 10−2 N
B. 1.4 × 10−2 N
C. 1.4π × 10−2 N
D. 2.4π2 × 10−2 N
E. 3.13 N
ans: B
52. A 0.2-kg stone is attached to a string and swung in a circle of radius 0.6 m on a horizontal
and frictionless surface. If the stone makes 150 revolutions per minute, the tension force of the
string on the stone is:
A. 0.03 N
B. 0.2N
C. 0.9N
D. 1.96 N
E. 30 N
ans: E
53. Which of the following five graphs is correct for a particle moving in a circle of radius r at a
constant speed of 10 m/s?
a a a
.
. .. ..
.. .
. .
. .
r . r . r
A B C
a a
. . .
.
.. .
. .
. .
.
. r . . r
D E
ans: E
54. An object moves around a circle. If the radius is doubled keeping the speed the same then the
magnitude of the centripetal force must be:
A. twice as great
B. half as great
C. four times as great
D. one-fourth as great
E. the same
ans: B

0
55. An object moves in a circle. If the mass is tripled, the speed halved, and the radius unchanged,
then the magnitude of the centripetal force must be multiplied by a factor of:
A. 3/2
B. 3/4
C. 9/4
D. 6
E. 12
ans: B
56. If a satellite moves above Earth’s atmosphere in a circular orbit with constant speed, then:
A. its acceleration and velocity are always in the same direction
B. the net force on it is zero
C. its velocity is constant
D. it will fall back to Earth when its fuel is used up
E. its acceleration is toward the Earth
ans: E
57. A 800-N passenger in a car presses against the car door with a 200 N force when the car makes
a left turn at 13 m/s. The (faulty) door will pop open under a force of 800 N. Of the following,
the least speed for which the passenger is thrown out of the car is:
A. 14 m/s
B. 19 m/s
C. 20 m/s
D. 26 m/s
E. 54 m/s
ans: D
58. If a certain car, going with speed v1, rounds a level curve with a radius R1, it is just on the
verge of skidding. If its speed is now doubled, the radius of the tightest curve on the same road
that it can round without skidding is:
A. 2R1
B. 4R1
C. R1 /2
D. R1 /4
E. R1
ans: B
59. An automobile moves on a level horizontal road in a circle of radius 30 m. The coefficient of
friction between tires and road is 0.50. The maximum speed with which this car can round
this curve is:
A. 3.0 m/s
B. 4.9 m/s
C. 9.8 m/s
D. 12 m/s
E. 13 m/s
ans: D

1
60. The driver of a 1000-kg car tries to turn through a circle of radius 100 m on an unbanked curve
at a speed of 10 m/s. The actual frictional force between the tires and slippery road has a
magnitude of 900 N. The car:
A. slides into the inside of the curve
B. makes the turn
C. slows down due to the frictional force
D. makes the turn only if it goes faster
E. slides off to the outside of the curve
ans: E
61. A car rounds a 75-m radius curve at a constant speed of 18 m/s. A ball is suspended by a
string from the ceiling the car and moves with the car. The angle between the string and the
vertical is:
A. 0
B. 1.4◦
C. 24◦
D. 90◦
E. cannot be found without knowing the mass of the ball
ans: C
62. A giant wheel, having a diameter of 40 m, is fitted with a cage and platform on which a man of
mass m stands. The wheel is rotated in a vertical plane at such a speed that the force exerted
by the man on the platform is equal to his weight when the cage is at X, as shown. The net
force on the man at point X is:
X
..
.
• ...............
. . ..
man in
.. . ...
..
...
...
............
....
cage
.. ....
.
..
. . ..........
.... . . ..
.
....
... .
. ......
.
. .......
. . .
.
.
.. ..
. ..
. . .
. ..... ..... .
...........
wheel
A. zero
B. mg, down
C. mg, up
D. 2mg, down
E. 2mg, up
ans: D

2
63. A giant wheel, 40 m in diameter, is fitted with a cage and platform on which a man can stand.
The wheel rotates at such a speed that when the cage is at X (as shown) the force exerted by
the man on the platform is equal to his weight. The speed of the man is:
X
•
. . . . . . .... .
......... . man in
.. . ..
.
.
...
...
... ....
....
cage
....
..
. ..
. ..... ....
......
.... .. .
.... .
. .
. ...
.. ...
. ... .
. .
.. .
.. .
..
. .
. .
. ... .. .
.
wheel
..............
A. 14 m/s
B. 20 m/s
C. 28 m/s
D. 80 m/s
E. 120 m/s
ans: B
64. A person riding a Ferris wheel is strapped into her seat by a seat belt. The wheel is spun so
that the centripetal acceleration is g. Select the correct combination of forces that act on her
when she is at the top. In the table Fg = force of gravity, down; Fb = seat belt force, down;
and Fs = seat force, up.
Fg Fb Fs
A. 0 mg 0
B. mg 0 0
C. 0 0 mg
D. mg mg 0
E. mg 0 mg
ans: B
65. One end of a 1.0-m long string is fixed, the other end is attached to a 2.0-kg stone. The stone
swings in a vertical circle, passing the bottom point at 4.0 m/s. The tension force of the string
at this point is about:
A. 0
B. 12 N
C. 20 N
D. 32 N
E. 52 N
ans: E

3
66. One end of a 1.0-m string is fixed, the other end is attached to a 2.0-kg stone. The stone
swings in a vertical circle, passing the top point at 4.0 m/s. The tension force of the string (in
newtons) at this point is about:
A. 0
B. 12
C. 20
D. 32
E. 52
ans: B
67. A coin is placed on a horizontal phonograph turntable. Let N be the magnitude of the normal
force exerted by the turntable on the coin, f be the magnitude of the frictional force exerted
by the turntable on the coin, and fs, max be the maximum possible force of static friction. The
speed of the turntable is increased in small steps. If the coin does not slide, then
A. N increases, f increases, and fs, max stays the same
B. N increases, f increases, and fs, max increases
C. f increases and both N and fs, max stay the same
D. N , f , and fs, max all stay the same
E. N , f , and fs, max all increase
ans: C
68. The iron ball shown is being swung in a vertical circle at the end of a 0.7-m long string. How
slowly can the ball go through its top position without having the string go slack?
...
. ..
. ... . . .
.•
..••.•..•.••. ......
. ....
. .
..
....
. .
.
.. • .
..
..
..
.. . ..
. .... .
....
A. 1.3 m/s
B. 2.6 m/s
C. 3.9 m/s
D. 6.9 m/s
E. 9.8 m/s
ans: B
69. A block is suspended by a rope from the ceiling of a car. When the car rounds a 45-m radius
horizontal curve at 22 m/s (about 50 mph), what angle does the rope make with the vertical?
A. 0
B. 25◦
C. 48◦
D. 65◦
E. 90◦
ans: C

4
70. Circular freeway entrance and exit ramps are commonly banked to handle a car moving at
13 m/s. To design a similar ramp for 26 m/s one should:
A. increase radius by factor of 2
B. decrease radius by factor of 2
C. increase radius by factor of 4
D. decrease radius by factor of √
4
E. increase radius by factor of 2
ans: C
71. At what angle should the roadway on a curve with a 50 m radius be banked to allow cars to
negotiate the curve at 12 m/s even if the roadway is icy (and the frictional force is zero)?
A. 0
B. 16◦
C. 18◦
D. 35◦
E. 73◦
ans: B

5

40 TestBank06

Uploaded by

Copyright:

Available Formats

40 TestBank06

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

40 TestBank06

Uploaded by

Copyright:

Available Formats

Chapter 6: FORCE AND MOTION – II

2. The coeﬃcient of kinetic friction:

66 Chapter 6: FORCE AND MOTION – II

7. A crate with a weight of 50 N rests on a horizontal surface. A person pulls horizontally on it

Chapter 6: FORCE AND MOTION – II 67

68 Chapter 6: FORCE AND MOTION – II

Chapter 6: FORCE AND MOTION – II 69

70 Chapter 6: FORCE AND MOTION – II

Chapter 6: FORCE AND MOTION – II 71

72 Chapter 6: FORCE AND MOTION – II

A. the short side is smoother

Chapter 6: FORCE AND MOTION – II 73

74 Chapter 6: FORCE AND MOTION – II

Chapter 6: FORCE AND MOTION – II 75

76 Chapter 6: FORCE AND MOTION – II

Chapter 6: FORCE AND MOTION – II 77

78 Chapter 6: FORCE AND MOTION – II

80 Chapter 6: FORCE AND MOTION – II

82 Chapter 6: FORCE AND MOTION – II

86 Chapter 6: FORCE AND MOTION – II

Chapter 6: FORCE AND MOTION – II 87

Chapter 6: FORCE AND MOTION – II 89

90 Chapter 6: FORCE AND MOTION – II

... ... ... .. .... .... .. .. ..

Chapter 6: FORCE AND MOTION – II 97

98 Chapter 6: FORCE AND MOTION – II

Chapter 6: FORCE AND MOTION – II 99

10 Chapter 6: FORCE AND MOTION – II

Chapter 6: FORCE AND MOTION – II 10

10 Chapter 6: FORCE AND MOTION – II

Chapter 6: FORCE AND MOTION – II 11

Chapter 6: FORCE AND MOTION – II 11

11 Chapter 6: FORCE AND MOTION – II

12 Chapter 6: FORCE AND MOTION – II

Chapter 6: FORCE AND MOTION – II 12

12 Chapter 6: FORCE AND MOTION – II

Chapter 6: FORCE AND MOTION – II 12

Chapter 6: FORCE AND MOTION – II 12

12 Chapter 6: FORCE AND MOTION – II

Chapter 6: FORCE AND MOTION – II 13

Chapter 6: FORCE AND MOTION – II 13

Chapter 6: FORCE AND MOTION – II 13

Chapter 6: FORCE AND MOTION – II 13

Chapter 6: FORCE AND MOTION – II 13

14 Chapter 6: FORCE AND MOTION – II

Chapter 6: FORCE AND MOTION – II 14

14 Chapter 6: FORCE AND MOTION – II

Chapter 6: FORCE AND MOTION – II 14

14 Chapter 6: FORCE AND MOTION – II

Chapter 6: FORCE AND MOTION – II 14

14 Chapter 6: FORCE AND MOTION – II

Chapter 6: FORCE AND MOTION – II 14

14 Chapter 6: FORCE AND MOTION – II

Chapter 6: FORCE AND MOTION – II 14

15 Chapter 6: FORCE AND MOTION – II

Chapter 6: FORCE AND MOTION – II 15

15 Chapter 6: FORCE AND MOTION – II

Chapter 6: FORCE AND MOTION – II 15

15 Chapter 6: FORCE AND MOTION – II