Ordering number: EN2119D

CMOS LSI
LC7461M

Infrared Remote Control Transmitter IC

Functions Package Dimensions

. 32%3 function keys unit : mm
. 13-bit custom codes 3045B-MFP24
. Operating supply voltage range V = 1.8 to 3.6 V
. Supply current at the standby mode I = 1 µA or less
DD
[LC7461M]
. Double-press operation keys (no priority given)
DD

. On-chip oscillator (ceramic resonator : connected externally)

Features
. The custom code consists of 7 bits to be fixed by the
on-chip ROM and 6 bits being pin-settable. Sixty-four
custom codes may be selected externally (no diode required).
. Minimum number of external parts required

SANYO : MFP24

Specifications
Absolute Maximum Ratings at Ta = 25°C

Parameter Symbol Conditions Ratings Unit

Maximum supply voltage VDD max VDD VSS–0.3 to +5.5 V
Input voltage VIN Each input pin VSS–0.3 to VDD+0.3 V
Output voltage VOUT Each output pin VSS–0.3 to VDD+0.3 V
Output current IOUT OUT –35 mA
Allowable power dissipation Pd max Ta % 85°C 150 mW
Operating temperature Topr –40 to +85 °C
Storage temperature Tstg –50 to +125 °C

Allowable Operating Conditions at Ta = 25°C

Parameter Symbol Pin Name Conditions min typ max Unit

Supply voltage VDD VDD fOSC = 455 kHz 1.8 3.0 3.6 V
KI0 to KI3,
Input high-level voltage VIH 0.7 VDD VDD V
C0 to C5
KI0 to KI3,
Input low-level voltage VIL VSS 0.3VDD V
C0 to C5
Oscillation frequency fOSC 400 455 500 kHz

SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters

TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110 JAPAN
O3096HA(II)/7058YT/6036KI,TS(KOTO) No.2119-1/7
 LC7461M

Electrical Characteristics at Ta = 25°C, VDD = 3.0 V

Parameter Symbol Pin Name Conditions min typ max Unit

Operating supply
IDD VDD Key ON, output: no load 1 mA
current
Quiescent supply
IDS VDD All keys OFF, OSC stop 1 µA
current
Output high-level IOH1 OUT VDD = 1.8 V, VOH = 1.0 V –8 mA
current IOH2 OUT VDD = 3.0 V, VOH = 1.0 V –25 mA
Output high-level
VOH KO0 to KO7 IOH = –0.1 mA 0.3 V
voltage
Output low-level
VOL OUT IOL = 0.1 mA 0.3 V
voltage
Output OFF-state
IOFF KO0 to KO7 1 µA
leakage current
Input high-level current IIH C0 to C5 VIN = VDD 1 µA
Input low-level current IIL C0 to C5 VIN = VSS –1 µA
Input floating voltage VIF KI0 to KI3 0.1 VDD V
Input pull down
RIN KI0 to KI3 75 100 125 kΩ
resistance

Internal Block Diagram

Key
output
timing Output
signal circuit
generator

Oscillator Divider Decoder

Key
entry Key data
circuit register
Custom code
register

No.2119-2/7
 LC7461M

Pin Assignment

Top view

Pin Description

Pin Name Pin No. Input/Output Internal Equivalent Circuit Pin Function
VDD, VSS 8, 12 Power supply pins VSS = GND

KO0 to KO7 13 to 20 Output Key scan timing signal output pins

KI0 to KI3 1 to 4 Input Keys return signal entry pins

Input/output pins for ceramic resonator-used

oscillation

OSC1 10
Input/output
OSC2 11

Oscillator configuration
Input pins for custom code setting
21 to 24,
C0 to C5 Input Capable of externally setting 6 bits of 13 bits in
5, 6
all that provide a custom code

OUT 7 Output Output pin for transmit LED drive

LSI test pin

TEST 9 Input Normally set to high-level or brought to open
state

No.2119-3/7
 LC7461M

General Description of Function

1. Oscillator
Since a self-bias type amplifier of CMOS inverter is contained, an oscillator can be formed by connecting a ceramic
resonator.

To minimize power dissipation, the oscillator stops oscillating except when key operation is performed.

2. Key entry
Key entry pins KI0 to KI3 and timing signal output pins KO0 to KO7 provide a key matrix of 4 × 8 = 32.

Multi-press of key No. 20 and one of key No. 21, 22, 23 may be done, with no priority given in key entry. When the two
keys are kept pressed, a series of pulses will be output according to each key entry. If multi-press of keys which are not
allowed multi-press is done, no output will be delivered.

3. Data organization
Data consists of 42 bits in all: 13 bits of custom code, 8 bits of key data, and their inverted codes.

Custom code Custom code Key data Key data

13 bits 13 bits 8 bits 8 bits

No.2119-4/7
 LC7461M

(a) Custom code

The custom code, which consists of 13 bits (C0 to C12) in all, is used to distinguish between receiving sets.

Pin-selectable Mask ROM

6 bits 7 bits

C6 to C12 are fixed by the mask ROM and C0 to C5 are pin-settable.

In this example C0 to C5 are

set as follows:

C0 C1 C2 C3 C4 C5
0 1 1 0 0 1

The custom codes are controlled by Sanyo to avoid duplication.

(b) Key data

KEY No.
Multi-press
D0 D1 D2 D3 D4 D5 D6 D7
0 0 0 0 0 0 0 0 0 KEY No. D0 D1 D2 D3 D4 D5 D6 D7
1 1 0 0 0 0 0 0 0 20, 21 1 0 1 0 1 1 0 0
2 0 1 0 0 0 0 0 0 20, 22 0 1 1 0 1 1 0 0
3 1 1 0 0 0 0 0 0 20, 23 1 1 1 0 1 1 0 0
4
5.
0
1.
0
0.
1
1.
0
0.
0
0.
0
0.
0
0.
0
0.
.D,D
6 7 may be preset to ‘‘0’’,‘‘1’’ beforehand (mask
.. .. .. .. .. .. .. .. .. option).
28 0 0 1 1 1 0 0 0
29 1 0 1 1 1 0 0 0
30 0 1 1 1 1 0 0 0
31 1 1 1 1 1 0 0 0

When multi-press of key No.20 and one of key No.21, 22, 23 is done, multi-bit D5 will be set to ‘‘1’’, with no priority given
in key entry.

(H: Key-ON state)

Key 20 Keys 20, 21 Key 21 Transmit Key 22 Keys 20, 22

data multi-press data stop data multi-press data
transmit data transmit transmit transmit transmit

No.2119-5/7
 LC7461M

4. Transmit waveforms
The period of time shown below is for fOSC = 455 kHz.

Custom code Custom code Key data Key data

13 bits 13 bits 8 bits 8 bits

Leader code

. First time

. Second time onward (Transmission is available only when key entry continues.)

. Carrier waveform

Carrier frequency = 1/12 fOSC 7 38 kHz

No.2119-6/7
 LC7461M

Sample Application Circuit

Transmit
LED

In this example custom code C0 to C5 is C0 z z z z z C5.

010101

No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace equipment,
nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of which may directly or
indirectly cause injury, death or property loss.

Anyone purchasing any products described or contained herein for an above-mentioned use shall:
1 Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors
and all their officers and employees, jointly and severally, against any and all claims and litigation and all damages, cost and
expenses associated with such use:
2 Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on SANYO
ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees jointly or severally.

Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume
production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use
or any infringements of intellectual property rights or other rights of third parties.

This catalog provides information as of October, 1996. Specifications and information herein are subject to change without notice.

No.2119-7/7