ROCKWOOL

SUPPLIED BY
 CONSTRUCTION OF NEW COLLEGE
PROJECT : OF EDUCATION BUILDING QATAR
UNIVERSITY (DH1318)

CLIENT :

CONSULTANT:

MAIN CONTRACTOR:
 CONSTRUCTION OF NEW COLLEGE OF EDUCATION BUILDING - QATAR UNIVERSITY

CHECKLIST FOR MATERIAL APPROVAL

MATERIAL NAME

S. No. Description Complied Remarks

1 Material Description

2 Project Specification Compliance Statement

3 Highlighted Specification

4 Highlighted IFC Drawings

5 Technical Data Sheet

Original catalogue and data sheets for proposed
6 manufacturer

7 Material Safety Data Sheet

8 Installation Instruction / Method Statement

9 Country of Origin Certificate

10 Project References

11 Compliance with GSAS requirements

12 Test Results / Certificate for particular material

13 Prequalifcation for Testing Agency

NA
14 Mix Designs
NA
15 Calculations

16 Warranty / Guarantee Certificate

NA
17 Extra Materials
NA
18 Spare Parts
NA
19 Factory Visit
NA
20 Maintenance Manual
To be done separatly
21 Mock Up
To be submitted separatly
22 Sample

CHECKED BY:
 INDEX

1. Material Description

2. Project Specification Compliance Statement

3. Highlighted Specification

4. Highlighted IFC Drawings

5. Technical Data Sheet

6. Original catalogue and data sheets for proposed manufacturer

7. Material Safety Data Sheet

8. Installation Instruction / Method Statement

9. Country of Origin Certificate

10. Project References

11. Compliance with GSAS requirements

12. Test Results / Certificate for particular material

13. Prequalification for Testing Agency

14. Warranty / Guarantee Certificate

1. Material Description
 SCHEDULE OF MATERIAL PROPOSED

Material
Sr. Manufacturer Material Description
Name

ROXUL
1 ROCKWOOL 50 MM X 64
KG/M3
2. Project Specification Compliance Statement
3. Highlighted Specification
QCS 2014 Section 15: Insulation of Buildings Page 6
Part 02: Building Insulation

2.4 INSULATION MATERIAL TYPES

2.4.1 General

1 Various types of insulation may be specified for varying conditions or wall construction. The
BS, EN classification system is to be used for insulation material; or to any other reference
mentioned in paragraph 2.1.2 , or approved by Qatar Standards.

2 The Contractor shall use only one type of insulation in any particular area where more than
one type is optional unless approved other wise by the Engineer.

3 At least thermal insulation is to be used for exterior roofs and exterior walls of the building

4 Where insulation is used for exterior walls, roof surfaces, or below grade, the requirements

.
for condensation control shall be to BS 5250 and BS 5803.

.L
2.4.2 External Thermal Insulation Composite System (ETICS)

.L
W
1 If specified the external thermal insulation composite system (ETICS) shall be bonded
system and tested in accordance with ETAG-004 (European organization for technical
approvals):-
o.
C
2 The external thermal insulation system shall compose of the following components:-

(a) Adhesive layer

g
in

(b) Extruded or expanded Polystyrene board

(c) Insulation boards fasteners (Plastic or metal)
ct

(d) Cementitious adhesive protective mortar layer

tra

(e) Fibremesh reinforcement

on

(f) Cementitious adhesive protective mortar layer

(g) Decorative layer of acrylic or polymer modified cementitious mortar
C

2.4.3 Cavity Wall Insulation

BK

1 Mineral Fibre Board shall comply with the relevant provisions of BS 1142 and be faced with a
vapour retarder having a perm rating of not more than 0.5.
H

2 Polyurethane or polyisocyanurate board shall comply with the relevant provisions of BS 4841
and be faced with a vapour retarder having a perm rating of not more than 0.5.

3 Polystyrene board shall comply with the relevant provisions of BS 3837.

4 Foam system insulation used in cavity walls shall be to BS 5617 and BS 5618.

5 Unless otherwise stated on the drawings cavity wall insulation shall be extruded polystyrene
3
board of minimum density 25 kg/m to the thickness detailed.

2.4.4 Perimeter Insulation

1 Polystyrene board where used for exterior perimeter insulation below ground and in contact
with soil shall comply with the relevant provisions of BS 3837 and BS 8216.

2 Where sprayed lightweight mineral coatings are used, they shall be to BS 8216.
4. Highlighted IFC Drawings
5. Technical Data Sheet
PRODUCT DATA SHEET
Issued: 14-07-2015 ROCKWOOL Technical Insulation
Residential and Commercial Insulation

Multiboard 64

Product description
Multiboard is an insulation slab designed for general insulation purposes. It is manufactured in a wide variety of thicknesses and densities to
suit most requirements, suitable for general application in residential, commercial and industrial buildings. Multiboard offers a wide range of
multipurpose usage in metal deck roofs, attics, ceilings, general partition application where no load-bearing insulation slabs are required. It may
be used for metal stud partitions for easy installation where no sagging or slumping of the insulation product will occur.

Product properties
Performance Norms

Nominal density 64kg/m³

Thermal conductivity at 20° 0.034 ASTM C518

C – λ (W/m.K)*

Fire performance A1 Fire classification/ Non-combustible EN 13501-1/UL 723

Water vapor absorption* ASTM C1104/C1104M 0.04% by Vol

Water absorption < 1 kg/m EN 1609:97

(partial immersion)

*typical values

Acoustic Absorption Data

ASTM 423
CO-EFFICIENTS AT FREQUENCIES

Thickness 125Hz 250Hz 500Hz 1000Hz 2000Hz 4000Hz NRC Class

50mm 0.13 0.72 0.99 1.05 0.96 0.90 0.93 A

75mm 0.27 0.95 1.05 1.04 0.97 0.93 1.00 A

100mm 0.33 0.97 1.08 1.06 1.02 0.96 1.03 A

ROXUL ROCKWOOL
PRODUCT DATA SHEET
Issued: 14-07-2015 ROCKWOOL Technical Insulation
Residential and Commercial Insulation

Multiboard 64

Typical applications
• External facades
• Internal partitions
• Roofing systems

Dimensions:
• 1200 x 600 mm (length x width) • 30, 50, 75 or 100 mm thickness (Other
• 1000 x 600 mm (length x width) thickness available on request)

Facings available:
• Aluminium Foil
• Black Glass Tissue

Packaging and storage handling

Multiboard 64 is shrink-wrapped in polyethylene sheets for ease of handling, transportation, storage and
identification. Products should be stored indoors or under a waterproof covering.

ROXUL ROCKWOOL Group

6. Original catalogue and data sheets for proposed manufacturer
# tl
Provider of
Comfort & Safety
e
As the worldas largest provider of fire safe stone wool
insulation, the ROCKWOOL Group operates in over
40 countries across Europe, North America and Asia.
The company was founded in 1937 and is headquartered
in Denmark.

The ROCKWOOL Group had supplied solutions to the Aiian matkeis since the
1980s, and in 1999 esiablished its presence in South East Asia with a plant in
Melaka. In 2010, ihe etoup acqu=ed production lacililies in China. Malaysia
and Thailand, serving the markets with offices in Beijing. Tianjin. Shanghai.
Guangihou, +long Kong, Philippinss and Taiwan. IIs presence in Aiia was further
strengthened in 2011 with ihe establishment oT a plant and sales office In India.

In South Asia ioday we have tour stone wool factories located in India. Malaysia
and Thailand and offices in India. Indonesia. Malaysia, Singapore. Thailand and
Vietnam serving the needs of customers acioig this region lo neighbounng
countries of Australia. New Zealand, Japan and South Korea.

CREATE AND PROTECTa

Our Mission & Values

Our mission is a statement oT Ihe core purpose of the company - an gpiession ol

what we hope to achieve through the solutions we offer and the values we practise.

0ur Misiian

The people of ROCKWOOL ane guided by the values of the company: which form the
basis of our thoughts. actions and the way we interact with customers and partners.
Our values are not lofty ideals wStien on papec They instruck our decisions. anthor
every product and service and reflect what we stand Tor as a company.

Responsibility

Our
Values

EllitientV

Enlrepieneutship
 Sustainable Solutions for
Buildings & Industries

Bulldings and indiisiries

across Asia with
ROCKWOOL insulation

€
The ROCKWOOL Difference Unique Benefits -
Lasting Solutions

Often unseen yet silently making a difference -

ROCKWOOL solutions have over the centuries been
protecting people, keeping them safe and comfortable
in every area of their life; at work and play.

Wheihsr it be part of theviorld's most iconic buildings, used in all types of

industrial processes or just keeping Tamilies safer and ha ppier in their
homes, we took the functionality of stone wool and made it into a brand that
is built to last.

The ROCKWOOL" brand is known all over the world today as providing
the highest quality stone WOOI solutions that offers consistent and lasting
performance in fire, thermal and acoustics. Ii is backed by over 75 years
of industry experience and enviriinmentally sound produciion facilities.
We endeavaur ta meet the mast stringent safety standards while providing
exceptional stone wool solutions, expert tools and impeccable service.

Our customers and partners know they can depend on

us to deliver solutions that perform as promised, time
and time again.

ThiS :S becausethe benefits 01 ROCKWOOL insulation are unitlue, a

combination of Tour benefits in tire resistance. noise reduction, thermal
comfort and sustainability packed into one solution.

4inl[ 6 si) $ 4 ]
ROCKWOOL solutions are tailored to meet the varied needs oj the market -
whether it is for the insulation of building envelopes to reduce energy usage
and carbon emissions and create a healthier and safer indoor environment or
technical mstallations to help reduce energy loss, increase business profits
and protect personnel safety.
 Beyond SoLutions - ROCKWOOL Group's
To People SustainabiLity & Corporate
Socia( Responsibi(ity

The ROCKWOOL Group subscribes to the 3 Pillars of

Sustainabikity: People, Planet and Prosperity.

People's health, safeiy and quality oL life are important to us. This is why we
are committed to ensunng our solutions help improve the periormance of
buildings in terms of comfort, energy savings and fire safety.

Our products are made from rocks, an abundant raw material We are
dedicated to using natural resources, recycling waste materials and reducing
resource use and emissions from out production in order to protect our
Ranet.

In line with ROCKWOOL Group's Social Responsibility commilments, we

contribute to the Prosperity oT communities and society in general. The
ROCKWOOL Foundation is an example in which a quarier o{ the Group's
dividend is used to support social enttepreneurship in order to achieve lasting
and sustainable improvements.

Our people in ROCKWOOL are what distinguishes us

from others. It is because we are passionate - about
:i people, about their safety and about creating the best
solutions at no cost to the enwonment.
1%4. l II Ik ..l

We understalid total building and process performance, how to achieve

excellent energy etticieticy, fke safety aiid indoor comkirk. With oiir
knowledge, we facilitate and support customers, partners, industry
professionals and government bodies to ensure buildings and industnes will
perjorm and protect us as they should.

s. CREATE AIIIO PROTECTa

ROCKWOOL IN ASIA

FACTORIES OFFICES

ROCKWOOL FIRESAFE INSULATION BEUING HEAD OFFICE INDONESIA REPRESENTATIVE OFFICE

IGUANGZHOUi CO LTD Raoml € EF1 TowerB GatewayPlaza AXA Tower 45"' Floor Jl Prof Di Satrio
3 Taihua St Yonghe Dist oT Guangzhou No 18 Xiaguangli East 3"Ring Road Kavi8 Kuningan Setiabudi Jakarta
Eoon & Tech Devgliipm*ni giii.
0uangzhou 0uan(dong ?rovlncg
P R China (511 3561 T i+861 1 € 659 € 6077 Fi+621 2i 3005 360 €
T 1+861 20 8298 66 68
P 1*!141 II Ilfl 41ff ROCKWOOL FIRESAFE INSULATION ROCKWOOL BUILDING MATERIALS
tGUANGZHOUI CO LTD IPHILIPPINESI LTD
ROXUL-ROCKWOOL Unit 2515 Profit Plaza No 76 Unit 702 7F Page I Bldg
INSULATION INDIA PVT LTD Wesj Huangpu Rd Tianhe Dist 1215 Acacia Avenue
Plot-Z/A Daliel SEZ Dahej
District Bharuch 392i3[)
Gujarat-India T (+861 2€ 3839 3636 T1+631 2 7710 650
T 1+9T1 2641 619400 F (+861 20 3839 3637 F 1+631 2 7710 649
F [+911 2641 256292
ROCKWOOL FIRESAFE INSULATION ROCKWOOL BUILDING MATERIALS
ROCKWOOL MALAYSIA SDN BHD ISHANGHAII CO LTD [SINGAPORE) PTE LTD
Lot 4 Solok Wala 1 Rooml401 Summit Centre No 8 Tuas Avenue 2 Jurong Town
Bukit Raja Industrial Estti}e 1088 Yan an West Rd Singapore 63%48
41050 Klang Selangor Malaysia Chan@qip@ 'llllii @hen@ha T 1+651 6861 4722
T [+60) 3 3341 3t44 4 QJ:Apg 120CD52) F i+651 68 62 3533

3 Intern.alonal !!u;lness Park

Urut No #02 24
Kawasan Perlndustrlan Alr X!rnh ROCKWOOL BUILDING MATERIALS Nordic European Centre
Jakan LtngJngsn usaha ITIANJINI CO LTD Singapore 609927
No BB 215 No 52 of West Financial Street T 1+65] 6933 7110
Bmhai New Area Tienjin 300457 F 1+6!1141@@fl @4/ 613@ 71@f
F 1+601 6 233 2012 T l+ffl gQ im 7778
ROCKWOOL tTHAILAND] LIMITED
ROCKWOOL ITHAILAND) LIMITED ROCKWOOL BUILDING MATERIALS B GRIMM BuildingTl" Floor
Hemaraj Eastern Industrial Estate HONG KONGi LTD
IMap Ta Phutl 1 Soi G 2 Unit 301 2 3/F Koon Wali Building
Pskornaan@knhral ffioad NO 2 Yuen Shun Circuit Yuen Chau Kok
Huaypong Muang Rayong :1150 Thailand
T 1+661 3868 5110 F f+661 2731 7510
F i+6 61 3868 4938
VIETNAM REPRESENTATIVE OFFICE
TAIWAN REPRESENTATIVE OFFICE 9"' Floor Maritime Bank Tower
Pa Boxli8-981Taipei 180 1 92 Nguyen (,ong Tru Street District 1
Taipei Cityl[l599 Taiwan IR O Cl Ho 6hl Minh Oity Vi*iqam
T I+gAl Q A2W 2009
F 1+8A1 8 6288 4691

ROXUL ROCKWOOLTECHNICAL
INSULATION INDIA PVT LTD 49 Hai Ba Trung Street
7[)5 Center Point J B Nagar Hoan Kiem District
AndhariJturla Road Hanoi Vietnam

P tmt is iris *rii

j4-00j,

ROCKWOOL sxuct
www rockwoolasia com
7. Material Safety Data Sheet
 ROaKWOOL
lillh@l)NllllAfl*N

Rockwool Technical Insulation Group

I SAFE USE INSTRUCTIONSSHEET' I

1. PRODUCT AND COMPANY IDENTIFICATION

Generic product name STONEWOOL - High alumina, low silica wool

Thermal and /or acousUcal, vibration and technical insulation for construction,
industry, rail or marine application

Producer ROXUL ROCKWOOL

Rockwool Technical Insulation
Plot - Z/4, Dahej SEZ, Dahej
Dist. Bharuch - 392 5 30
Tel.: +9j 2641 258288
Fax: +9j 2641 256292
WWW.rockwool-rti.com

il 2. HAZARD8 IDENTIFICATION

Most important hazama : There is no Hazard statement associated with this product.

Specffle hazards Non applicable

3. COMPOSITION/INFORMATIONS on INGRED1ENT8
Classification and Classifloation and
Amount Index numbsr in accordance
labelling
C.A.S. labelling with
Substance weight (European
number"'> (Regulation (CE) Appendix I 87/541/EEC
(%) dired?ve
nol272/2008) 87/848/E:EC)"
Stone wool " 287922- 95 - Not classified ("' Not classified 650-C)al6-00-2
11-6 100%

Organic 0 - 5% Not classified Not classified

binder
0 - 0.5% Not classified Not classified
Mineral oil
fi
(1 ): Man-made vitreous (silicate) fibres with random orientation with alkaline oxide and alkali earth oxide
(Na20+K20+CaO+MgO+BaO) content greeterthan 18% by weight and fulfilling one of the nota Q conditions
(2): Non classified H351 'suspected of causing cancer'. Stone wool fibres are not classified carcinogenic according to
the nota Q of the Directive 97/89/EEC and the regulation no 1272/2008 (page 335 of the JOCE L353 of December
31 , 2008)
(3): Where substances are classified in accordance with regulation (EC) No 1272/2008 during the period from us entry
into force until 4 December 2010 that cfassification may be added in the safety data sheet together with the
classification in accordance with Directive 67/548/EEC. From 1 December 2010 until 1 June 2015 the safety data
sheets for substances shall contain the classification according to both Directive 67/548/EEC and RegulaUon (EC)
No 1272/2008 (art. 57 of Regulation (CE) 1272/2008, Official journal L353, p. 27)
(4): C.A.S. : Chemical Abstract Service

Possible fating materials: g[ass mat, or polyester mat or aluminium, wire mesh netting (galvanised or stainless steel)

' The European Regulation (ER) on Chemicals No 1907/2006 (REACH) enforced on June ]" 2007 requires Material Safety Data
Sheet (MSDS) only for hazardous substances and mixtures/preparations. Mineral wool products (panels or roles), are articles under
REACH and therefore, MSDS is not (egally required. Nevertheless, Rockwool decides to provide its customers with the
appmpriate information for assuring safe handding and use of mineral wool thmugh this Safe Use lnstructions Sheet.

Issue date: November 25-, 2010

 030(30001
lRl$ATl+Nluaafi*ai

4. FIRST AID MEASURES

Information accoming to the different exposure route:

- Inhalation : Remove from exposure. Rinse the throat and blow nose to clear dust

- Skin contact : If itching occurs, remove contaminated clothing and wash skin gently with cold water and
soap.

- Eyescontact : Rinseabundantlywithwaterforatleast15minutes.

- lngestion : Drink plenty of water if accidentally ingested.

If any adverse reaction or discomfort continues from any of the above exposures, seek medical professional advice.

5. FIRE FIGHTING MEA8URES

8uitable extinguishing media The products are non combusUble, some packaging materials or facings may
however be combustible.
li,
Suitable extinguishing media: water, foam, carbon dioxide (CO2), and dry powder.

6. ACCIDENT AL RELEASE MEAaURE3

In case of spillage Remove mechanically.

7. HANDLING and STORAGE

Handling

- Technlcal measures : No specific measure. lJse preferably a knife, If a power tool is used, it must
be equipped with efficient air sucUon.

- Precautions : Ensure adequate ventilation of workplace. See section 8

- Safe handling advice : Avoid unnecessary handling of unwrapped product. See section 8.

Storage

- Technical measures : No special measures necessary.

- Suitablestoragecondition : Products shouid be stored dry, If possible also materials in original

packaging. Materials without packaging should always be stored dry.

- Incompatible materials : None

- Packaging materJal : Products are packed in polyethylene film or cardboard; on wooden pallet

Issue date: November 25'h, 2010

 OdCkW**l
lal&A1llll1ll%Afl6f

8. EXPOSURE CONTROL8 / PERSONAL PROTECnON

Exposure Limit Value In accordance with naUonal regulations.

Individual protection equipments

- Respiratory protection When working in unventilated area or during operations which

can generate emission of any dust, wear a disposable face
mask. Type in accordance with EN 149 FFPj is recommended,

- Hand protection Use gloves to avoid itching in conformity with EN 388

- Eyes protection Wear goggles when working overhead. Eye protection to EN

166 is advised

- Skin protection Cover exposed skin

- Hygiene measures Rinse in cold water before washing

9. PHYSICAL and CHEMICAL PROPERTIES

Physical state : Solid

Form Rolf, slab or shaped article

Colour : Grey green

Odour Not relevant

: Not relevant

Boiling pomt : Not relevant

Flash point Not relevant

Explosive properties : Not relevant

Density : Product depending

Water solubility : Generally chemically inert and insoluble in water.

Melting point : > 1000 oC

10. STABILITY AND REACTMTY

Stability Binder will decompose above ca. 250"C

Dangerous reactions None in normal condiUons of use

Other information When mineral wool is heated to more than 250"C, this mrts a
decomposition reaction of the binder, the produds of which can be
detected by their odour. Emissions usually occur only during the first
heating of a mineral wool insulated apparatus. It is advisable to ensure
good ventilation when such appliances are first put into service. The
decomposition products are those that would be expected from any
organic material and are mainly derived from pyrolis or burning of the
resin. These decomposition products, which only occur for a short
time, are mainly CO2, CO, carbon partmles and water.
According to the test methods of DIN 53 436 the carbonisation gases
are regarded as toxicologically harmless.

11. TOXICOLOGICAL INFORMATION

Issue date: November 25", 2010

 RO € KWOOt'
Pll € lllrllff*lllAfl*N

Classification as carcinogenic not applicable for mineral wools in this product; in accordance with the directive
97/69/EC and European Regulation 1272/2008, nota Q. (See 8edion 15).
Owtng h:i thedr Mgh biomubility, Une fibm types of ROCKWDOI sfone woo/ insu?akin materials (HT sbne woo/ flbres) ate also assessed as fpBB
rmm suspmr:in d carctrmgenfc effeds in amrdance wish German Rub TRC;S 905, sad/on 2.3. The haft-life bme afbr inhstrachea! inmllation
(artificial applBatim offibres into ttte lungs d rats by injeclm thmugh the trachea) is /ass than 40 days fr>r W7-10 fibres (L > 5 pm, D < 3pm, L:D > 3)
as well as fwflbms with a length > 20 pm.

The fibres are Bio soluble.

12. ECOLOGICAL INFORMATION

This product is not expected to uuse harm to animals or plants during normal conditions of use.

13. D18PO3AL CONSIDERATIONS

Waste from residues : Dispose of in accordance with regulattns and prooedures in force in
country of use or disposal. Clean Rockwool waste can be supplied to
fj
some of the Rockwool factories to be recycled, after contact for the
transport and conditions.
There are no pmduct-technical restrictions that forbid the dumping of the
material in a waste depony.

Packaging disposal : Dispose of in accordanoe with local regulations. Packing material being
polyethylene can be supplied for recycling to PE manufacturers.

Code from European Waste Catalogue: 17 06 04 'lnsulating materials other than those mentioned in 17 06 0")
and 17 08 03'. Fulfils the requirements of 17 09 04 'Mixed construction
and demolition wastes other than those mentioned in 170901,
17 09 02 and j7 09 03'

14. TRANSPORT INFOMATtON

Intemational regulations : no specific regulations

15. REGuLATORY INFORMATION

The European directive 97/69/EC replaced by the regulation (EC) n' 1272/2008 conceming the classificaUon, labelling
and packaging of the substance and the mixtures does not classify Stone wool fibres as hazardous, if they are in
compliance with the note Q of this Regulation.

16. OTHER INFORMATION

German Code of Practice 'Handling of mineral wool insulation materials (glass wool, stone wool)", version: 05/2010

Pictograms on the packaging give handling instrudions to avoid temporary itching.

The 'GOtegemeinschaft Mineralwolle e. V.' has conferred ROCKWOOL STEINWOLLE the RAL quality label 'products
made of mineral wool' which is printed on the packaging.

All products manufactured by Rockwool BV are made of non-classffied fibres and are certified by ELICEB.

Issue date: November 25", 2010

 R@ € KW@@l

EUCEB, European Certification Board of Mineral Wool Products - www.euceb.orq, is a voluntary inhiative by the mineral
wool industry. It is an independent certification authority that guarantees that products are made of fibres, which comply
with the exoneration criteria for carcinogenicity (Note O) ofthe [)irective 97/69/EC and the Regulation (EC) 1272/2008.

To ensure that fibres comply with the exoneration criteria all tests and supervision procedures are carried out by
independent, expert qualified instituUons. El)CEB ensures that the producers of mineral wool have put in place self-
control measures.

The mineral wool producers commit to EUCEB to:

supply sampling and analysis reports established by laboratories recognized by EUCEB, proving that the fibres
comply with one of the four criteria of exoneration described in Note Q of the Directive 97/99/EC,
* be controlled, twice per year, of each production unit by an independent third party reoognized by EUCEB
(sampling and oonformity to the initial chemical composition),
* put in place pmcedures ofinternal self-control in each production unit.

The products responding to the EUCEB certification are recognized by the EUCEB logo put on the packaging.

Pemons who wish b obtain more detailed infomation have b contact the pmducer (address on the first page of this
sheet).

Infomation given in this document is O/? the stafe of our knowledge regarding this material at the time of issue.
It is glen in good faith.

The attention of users is drawn to possible risks taken when the pmduct /s used for other application than the ones it
has been designed for

li

Issue date: November 25'h, 2010

8. Installation Instruction / Method Statement
Engineering Consultants
In Environment , Noise & vibrations
Project Offer Ref Date
QATAR University NCL & NCE ALMO/PG/O0914/R4 30.7.2015

Rw 45 partition (M10)
Partition type I
Hollow concrete blocks 100 mm thick having a weight no less than 150 kg/m2
1980 m² plastered on both sides with 10 mm plastering

Partition type II Rw 50 partition (M15)

Hollow concrete blocks 150 mm thick having a weight no less than 230 kg/m2
5450 m² plastered on both sides with 20 mm plastering
Rw 55 partition (M20)
Solid filled concrete block 150 mm thick having a weight no less than 350 kg/m2
plastered on both sides with 20 mm plastering or reinforced concrete of the
same thickness
Partition type III
Or Alternatively
5380 m²
Hollow concrete blocks 200 mm thick having a weight no less than 270 kg/m2
plastered on both sides with 20 mm plastering
Rw 60 partition (M30)
Double block work wall consisting of :
-100 mm solid hollow concrete blocks having a weight no less than 140 kg/m2
plastered on outer side with 20 mm plastering
Partition type IV
-An air gap of 50 mm filled with 50 mm thick mineral wool boards , 60 kg/m3
density .
7800 m² -150 mm hollow concrete blocks having a weight no less than 230 kg/m2
plastered on outer side with 20 mm plastering
Rw 65 partition (M40)
Double block work wall consisting of :
-100 mm solid filled concrete blocks having a weight no less than 190 kg/m2
plastered on both sides with 20 mm plastering
Partition type V
-An air gap of 50 mm filled with 50 mm thick mineral wool boards , 60 kg/m3
225 m² density .
-150 mm hollow concrete blocks having a weight no less than 230 kg/m2
plastered on both sides with 20 mm plastering

Page 8 of 58
Ivoire Center Block B-2nd floor –Dimitri Hayek Street –Horsh tabet-Sin El Fil-P.O.Box 55112 , Beirut, Lebanon
Tel : +(961)-1-490887 - Fax : +(961)-1-491375 - E-mail :[email protected] - Web: www.alctrame.com
9. Country of Origin Certificate
 Country of Origin

Date: 20thJune , 2018 f.#: RFL-COO-18031A06007

Project CONSTRUCTION OF NEW COLLEGE OF EDUCATION BUILDING QATAR UNIVERSITY (DH1318)

Client QATAR UNIVERSITY

Contractor: Boom General Contractors

To whom it may concerns,

We, UNITECH Qatar for building and construction materials LTD. WLL., do hereby confirm that the
ROCK WOOL submitted to above mentioned project is manufactured in INDIA.

Al-Shimaa Galal| UNITECH QATAR for building & construction materials LTD. WLL.
CIVIL / Techical Engineer
TEL: +974 4451 3301 | FAX: +974 4451 3305 | MOB: +974 6616 3472
[email protected] | website: www.unitech-qatar.com
10. Project References
11. Compliance with GSAS requirements
12. Test Results / Certificate for particular material
 ‫ﺗﺎﺭﻳﺦ ﺍﻟﻄﺒﺎﻋﺔ ‪2018-10-14 :‬‬ ‫ﻭﺯﺍﺭﺓ ﺍﻟﺪﺍﺧﻠﻴــــﺔ‬
‫ﻭﻗـﺖ ﺍﻟﻄﺒﺎﻋﺔ ‪ :‬ص ‪8:12‬‬ ‫ﺍﻻﺩﺍﺭﺓ ﺍﻟﻌﺎﻣﻪ ﻟﻠﺪﻓﺎﻉ ﺍﻟﻤﺪﻧﻲ‬
‫ﺭﻗــﻢ ﺍﻟﻄﻠـﺐ ‪PAC18012304 :‬‬ ‫ﺇﺩﺍﺭﺓ ﺍﻟﻮﻗﺎﻳﺔ‬

‫ﺷﻬــــــﺎﺩﺓ ﻋﺪﻡ ﻣﻤﺎﻧﻌﺔ‬

‫ﺍﻋﺘﻤﺎﺩ ﻣﻨﺘﺞ‬ ‫ﻧﻮﻉ ﺍﻟﺸﻬﺎﺩﺓ ‪:‬‬

‫ﺑﻴﺎﻧﺎﺕ ﺍﻟﻤﻨﺸﺄﺓ‬

‫ﺷﺮﻛﻪ ﻳﻮﻧﻴﺘﻚ ﻗﻄﺮ ﻟﻤﻮﺍﺩ ﺍﻻﻧﺸﺎﺀ ﻭﺍﻟﺘﻌﻤﻴﺮ ﺍﻟﻤﺤﺪﻭﺩﻩ‬ ‫ﺍﻻﺳﻢ ﺍﻟﺘﺠﺎﺭﻱ‪:‬‬

‫‪47173‬‬ ‫ﺭﻗﻢ ﺍﻟﺮﺧﺼﺔ ﺍﻟﺘﺠﺎﺭﻳﺔ‪:‬‬ ‫‪27501‬‬ ‫ﺭﻗﻢ ﺍﻟﺴﺠﻞ ﺍﻟﺘﺠﺎﺭﻱ‪:‬‬
‫ﺭﻗﻢ ﺍﻟﻬﺎﺗﻒ‪:‬‬ ‫‪11-8803-00‬‬ ‫ﺭﻗﻢ ﻗﻴﺪ ﺍﻟﻤﻨﺸﺄﺓ‪:‬‬
‫ﺍﻟﺒﺮﻳﺪ ﺍﻹﻟﻜﺘﺮﻭﻧﻲ‪:‬‬
‫‪Fire Rated and Retardant materials‬‬ ‫ﺍﻟﺘﺼﻨﻴﻒ ‪:‬‬
‫)‪Insulation Materials (Rockwool, Thermal insulators etc‬‬ ‫ﺇﺳﻢ ﺍﻟﻤﻨﺘﺞ ‪:‬‬

‫ﺗﻔﺎﺻﻴﻞ ﺍﻟﺸﻬﺎﺩﺓ‬

‫ﺗﻢ ﻣﺮﺍﺟﻌﺔ ﺍﻟﻄﻠﺐ ﺍﻟﻤﻘﺪﻡ ﻭﺍﺗﻀﺢ ﺑﺄﻧﻪ ﻻ ﻣﺎﻧﻊ ﻣﻦ ﺍﻋﺘﻤﺎﺩ ﺍﻟﻤﻨﺘﺞ ‪/‬ﺍﻟﻤﻨﺘﺠﺎﺕ ﺍﻟﻤﻮﺿﺤﻪ ﻓﻰ ﺍﻟﺘﻘﺮﻳﺮ ﺍﻟﻔﻨﻰ ﺍﻟﻤﺮﻓﻖ ﺑﻨﺎﺀ ﻋﻠﻰ ﺍﻋﺘﻤﺎﺩﻩ ﻣﻦ‬
‫ﻗﺒﻞ ﺍﻟﻬﻴﺌﻪ ﺍﻟﻤﺨﺘﺒﺮﻳﺔ ﺍﻟﻤﻮﺿﺤﻪ ﻓﻰ ﺍﻟﺘﻘﺮﺭ ﺍﻟﻔﻨﻲ ﺍﻟﻤﺮﻓﻖ‪.‬‬

‫ﻣﻼﺣﻈﺎﺕ ‪:‬‬

‫‪ .1‬ﻳﺠﺐ ﻋﻠﻰ ﺍﻟﺸﺮﻛﻪ ﺍﻻﻟﺘﺰﺍﻡ ﻭﺍﻟﻌﻤﻞ ﺑﻤﺎ ﺟﺎﺀ ﻓﻲ ﺍﺷﺘﺮﺍﻃﺎﺕ ﻗﺴﻢ ﺃﻧﻈﻤﺔ ﺍﻟﺴﻼﻣﻪ ﺍﻟﺘﻲ ﺗﻢ ﺍﻻﻃﻼﻉ ﻭﺍﻟﻤﻮﺍﻓﻘﺔ ﻋﻠﻴﻬﺎ ﻣﻦ ﺧﻼﻝ ﺍﻟﻤﻮﻗﻊ ‪.‬‬
‫‪ .2‬ﻳﺠﺐ ﺍﻥ ﻳﻘﻮﻡ ﺑﺘﺮﻛﻴﺐ ﻫﺬﺍ ﺍﻟﻤﻨﺘﺞ ﻣﻦ ﻗﺒﻞ ﻣﻬﻨﺪﺳﻴﻦ ﻭﻓﻨﻴﻴﻦ ﻣﻌﺘﻤﺪﻳﻦ ﻣﻦ ﺍﻹﺩﺍﺭﺓ ﺍﻟﻌﺎﻣﺔ ﻟﻠﺪﻓﺎﻉ ﺍﻟﻤﺪﻧﻲ‪.‬‬
‫‪ .3‬ﻳﺠﺐ ﺍﻥ ﻳﺤﻤﻞ ﺍﻟﻤﻨﺘﺞ ﺍﻟﻌﻼﻣﺔ ﺍﻟﺘﺠﺎﺭﻳﺔ ﻟﻠﻬﻴﺌﻪ ﺍﻟﻤﺨﺘﺒﺮﻳﺔ ﺍﻟﻤﻌﺘﻤﺪﺓ ﻭﺍﻟﻤﻮﺿﺤﻪ ﻓﻲ ﺍﻟﺘﻘﺮﻳﺮ ﺍﻟﻔﻨﻲ ﺍﻟﻤﺮﻓﻖ ‪.‬‬

‫‪13/10/2020‬‬ ‫ﺗﺎﺭﻳﺦ ﺍﻹﻧﺘﻬﺎﺀ ‪:‬‬ ‫‪14/10/2018‬‬ ‫ﺗﺎﺭﻳﺦ ﺍﻻﻋﺘﻤﺎﺩ ‪:‬‬

‫ﻉ‪/‬‬

‫ﻣﺪﻳﺮ ﺇﺩﺍﺭﺓ ﺍﻟﻮﻗـﺎﻳـــــﺔ‬

‫ﺍﻹﺩﺍﺭﺓ ﺍﻟﻌﺎﻣﺔ ﻟﻠﺪﻓﺎﻉ ﺍﻟﻤﺪﻧﻲ‬

‫‪Page 1 of 2‬‬
 ‫ﺑﺴﻢ ﺍﻟﻠﻪ ﺍﻟﺮﺣﻤﻦ ﺍﻟﺮﺣﻴﻢ‬

DATE : 2018-10-14 : ‫ﺍﻟﺘﺎﺭﻳـــــــﺦ‬ ‫ﻭﺯﺍﺭﺓ ﺍﻟﺪﺍﺧﻠﻴﺔ‬

PERMIT PAC18012304 : ‫ﺭﻗﻢ ﺍﻟﻄﻠﺐ‬ ‫ﺍﻹﺩﺍﺭﺓ ﺍﻟﻌﺎﻣﺔ ﻟﻠﺪﻓﺎﻉ ﺍﻟﻤﺪﻧﻲ‬
‫ﺇﺩﺍﺭﺓ ﺍﻟﻮﻗﺎﻳﺔ‬

TECHNICAL REPORT ‫ﺍﻟﺘﻘﺮﻳﺮ ﺍﻟﻔﻨﻲ‬

PRODUCT : Insulation Materials (Rockwool, Thermal insulators etc) : ‫ﺍﻟﻤﻨﺘﺞ‬

PRODUCT APPLICATION : Fire Rated and Retardant materials : ‫ﺗﺼﻨﻴﻒ ﺍﻟﻤﻌﺪﺓ‬
APPLICANT / P.O .Box ‫ﺷﺮﻛﻪ ﻳﻮﻧﻴﺘﻚ ﻗﻄﺮ ﻟﻤﻮﺍﺩ ﺍﻻﻧﺸﺎﺀ ﻭﺍﻟﺘﻌﻤﻴﺮ ﺍﻟﻤﺤﺪﻭﺩﻩ‬ : ‫ﻣﻘﺪﻡ ﺍﻟﻄﻠﺐ‬
MANUFACTURER /
:‫ ﺑﻠﺪ ﺍﻟﺼﻨﻊ‬/ ‫ﺍﻟﺸﺮﻛﺔ ﺍﻟﻤﺼﻨﻌﺔ‬
ROXUL-ROCKWOOL INSULATION INDIA PVT. LTD /
LOCATION : INDIA

‫ﺍﻟﻮﺻﻒ‬ ‫ﺍﻟﻤﻮﺩﻳﻞ‬
UNFACED ROCKWOOL
Unfaced Rockwool Blanket, Flame Spread=0, Smoke Develop=0, Class-A
BLANKET

3RD PARTY ‫ﺷﻬﺎﺩﺓ ﺍﻟﻤﺨﺘﺒﺮﺍﺕ ﺍﻟﻤﺴﺎﻧﺪﺓ‬

CERTIFICATE / R27712- - R27712 - Underwriters
APPROVAL : 20130627 Laboratories : ( ‫)ﻣﻦ ﻫﻴﺌﺎﺕ ﻣﻌﺘﻤﺪﺓ‬
(UL)

RECOMMENDATIONS ‫ﺍﻟﺘﻮﺻﻴﺎﺕ‬
UL Cert. No. "BKNV.R27712"- The basic standard used to investigate products in this category is ANSI/UL 723,
"Test for Surface Burning Characteristics of Building Materials."

/‫ﻉ‬

‫ﻣﺪﻳﺮ ﺇﺩﺍﺭﺓ ﺍﻟﻮﻗـﺎﻳـــــﺔ‬

‫ﺍﻹﺩﺍﺭﺓ ﺍﻟﻌﺎﻣﺔ ﻟﻠﺪﻓﺎﻉ ﺍﻟﻤﺪﻧﻲ‬

Page 2 of 2
13. Prequalification for Testing Agency
14. Warranty / Guarantee Certificate
 Letter of warranty
Date : 29July,2018 Ref. No. RFL-LW-18038A07029
Project: CONSTRUCTION OF NEW COLLEGE OF EDUCATION BUILDING QATAR UNIVERSITY (DH1318)
Client: Qatar University
Contractor: Boom General Contractors

To Whom It May Concern;

Unipro Qatar for building and construction materials warrants all material supplied to the above mentioned job
site under description of ROCK WOOL in accordance with drawings, project specifications, related international
standard and contract/purchase orders, for a period of 5Years From substantial completion of the project .

Above mentioned is strictly limited, and cannot be extended under any circumstances, to the documents and drawings
submitted and returned back signed, dated and stamped by material engineering department.
No representative has the authority to vary or alter these terms.

Under this warranty; Unitech Qatar will be provided the opportunity to have one of its representatives assess any
damage identified to be caused by Unitech Qatar for building and construction materials.
If said damage is judged to be the fault of Unitech Qatar, entire liability of Unitech Qatar under this warranty is
limited to repair or replace in ROCK WOOL quantities sufficient to remedy any defective area, at no cost to the
Owner.

Unitech Qatar will not have any liability or obligation under this limited warranty, in case of;
 Any defect caused by misuse or abuse of the product.
 Any defect caused by normal wear and tear.
 Damage caused by natural disasters or force majeure.
 Any consequential damages
 Damage caused by unauthorized modification.
 Defects caused by improper storage of the product.
 Use of products in areas with corrosion category out of C2

The remedy set forth herein is the sole exclusive remedy of the owner. This warranty is given in lieu of any and all
other warranties, expressed or implied, including any implied warranty of merchantability or fitness for any particular
purpose. No representative has the authority to vary or alter these terms. In no event shall Unitech Qatar be liable for
any damage to the building or any other special, incidental or consequential damages.

Sincerely,
MATERIAL ENGINEERING DEPARTMENT