Scribd
Upload
93 views

Material Subjected To Combined Direct and Shear Stresses

This document summarizes the stresses acting on a material subjected to both direct and shear stresses. It discusses: 1) The material is under a complex stress system with direct stresses σx and σy, and shear stresses τyx and τxy. 2) This state of stress is a combination of pure shear stress and direct stresses acting perpendicularly. 3) Equations are derived to calculate the principal stresses and principal planes, which are the maximum and minimum normal stresses and the planes where shear stress is zero.

Uploaded by

Mechanical Zombie
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
93 views

Material Subjected To Combined Direct and Shear Stresses

This document summarizes the stresses acting on a material subjected to both direct and shear stresses. It discusses: 1) The material is under a complex stress system with direct stresses σx and σy, and shear stresses τyx and τxy. 2) This state of stress is a combination of pure shear stress and direct stresses acting perpendicularly. 3) Equations are derived to calculate the principal stresses and principal planes, which are the maximum and minimum normal stresses and the planes where shear stress is zero.

Uploaded by

Mechanical Zombie
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 6

LECTURE 4

Material subjected to combined direct and shear stresses:

Now consider a complex stress system shown below, acting on an element of material.

The stresses x and y may be compressive or tensile and may be the result of direct forces or as a result of
bending.The shear stresses may be as shown or completely reversed and occur as a result of either shear force
or torsion as shown in the figure below:

As per the double subscript notation the shear stress on the face BC should be notified as yx , however, we have
already seen that for a pair of shear stresses there is a set of complementary shear stresses generated such
that yx = xy

By looking at this state of stress, it may be observed that this state of stress is combination of two different cases:

(i) Material subjected to pure stae of stress shear. In this case the various formulas deserved are as follows

 = yx sin2

 = yx cos 2

(ii) Material subjected to two mutually perpendicular direct stresses. In this case the various formula's derived are
as follows.

To get the required equations for the case under consideration,let us add the respective equations for the above
two cases such that

These are the equilibrium equations for stresses at a point. They do not depend on material proportions and are
equally valid for elastic and inelastic behaviour
This eqn gives two values of 2 that differ by 1800 .Hence the planes on which maximum and minimum normal
stresses occurate 900 apart.

From the triangle it may be determined

                                                           

Substituting the values of cos2 and sin2 in equation (5) we get


This shows that the values oshear stress is zero on the principal planes.

Hence the maximum and minimum values of normal stresses occur on planes of zero shearing stress. The
maximum and minimum normal stresses are called the principal stresses, and the planes on which they act are
called principal plane the solution of equation

will yield two values of 2 separated by 1800 i.e. two values of  separated by 900 .Thus the two principal stresses
occur on mutually perpendicular planes termed principal planes.

Therefore the two � dimensional complex stress system can now be reduced to the equivalent system of
principal stresses.
Let us recall that for the case of a material subjected to direct stresses the value of maximum shear stresses

Therefore,it can be concluded that the equation (2) is a negative reciprocal of equation (1) hence the roots for the
double angle of equation (2) are 900 away from the corresponding angle of equation (1).

This means that the angles that angles that locate the plane of maximum or minimum shearing stresses form
angles of 450 with the planes of principal stresses.

Futher, by making the triangle we get


                               

Because of root the difference in sign convention arises from the point of view of locating the planes on which
shear stress act. From physical point of view these sign have no meaning.

The largest stress regard less of sign is always know as maximum shear stress.

Principal plane inclination in terms of associated principal stress:

We know that the equation 

yields two values of q i.e. the inclination of the two principal planes on which the principal stresses s1 and s2 act. It
is uncertain,however, which stress acts on which plane unless equation.

 is used and observing which one of the two principal stresses is
obtained.

Alternatively we can also find the answer to this problem in the following manner
Consider once again the equilibrium of a triangular block of material of unit depth, Assuming AC to be a principal
plane on which principal stresses p acts, and the shear stress is zero.

Resolving the forces horizontally we get:

x .BC . 1 + xy .AB . 1 = p . cos . AC   dividing the above equation through by BC we get

Goto Home

You might also like