YK - ALL MODELS

INSTALLATION, COMMISSIONING, REVISION 2 035-19569-101 (0109)

OPERATION AND MAINTENANCE

CENTRIFUGAL LIQUID CHILLER

STYLE G

R134A
 035-19569-101 (0109)

Table of Contents
1 SUPPLIER INFORMATION 1-1 4 INSTALLATION 4-1

1.1 Introduction 1-1 4.1 Location 4-1

1.2 Warranty 1-1 4.2 Motors 4-1

1.3 Safety 1-1 4.3 Foundation 4-1

1.4 Responsibility for Safety 1-1 4.4 Clearances 4-1

1.5 About this Manual 1-2 4.5 Rigging Unit to Final Location 4-1

1.6 Misuse of Equipment 1-2 4.6 Locating and Installing Isolator Pads 4-1

1.8 Safety Labels 1-3 4.7 Installing Optional Spring Isolators 4-2

1.9 Material Safety Data 1-4 4.8 Piping Connections 4-2

4.9 Evaporator and Condenser Water Piping 4-2

2 PRODUCT DESCRIPTION 2-1
4.9.1 Chilled Water Circuit 4-5
2.1 General 2-1
4.9.2 Condenser Water Circuit 4-5
2.2 Capacity Control 2-2
4.10 Stop Valves 4-6
2.3 Compressor 2-3
4.11 Flow Switches 4-6
2.4 Compressor Lubrication System 2-3
4.12 Drain and Vent Valves 4-6
2.6 Graphic Control Centre (OptiView) 2-5
4.13 Checking Piping Circuits and Venting Air 4-6
2.7 Heat Exchangers 2-5
4.14 Refrigerant Relief Piping 4-6
2.8 Refrigerant Flow Control 2-6
4.15 Unit Piping 4-7
2.9 Options and Accessories 2-6
4.16 Control Panel Positioning 4-7
2.10 Nomenclature 2-7
4.17 Control Wiring 4-7
2.11 Range of Models 2-8
4.18 Power Wiring 4-7

4.19 Units with Solid State Starter or

3 TRANSPORTATION, RIGGING AND STORAGE 3-1 Variable Speed Drive 4-8

3.1 General 3-1 4.20 Thermal Insulation 4-8

3.2 Shipment 3-1 4.21 Installation Check 4-8
3.3 Inspection, Damage and Shortage 3-2
5 COMMISSIONING 5-1
3.4 Rigging 3-3
5.1 Preparation 5-1

5.2 First Time Start-up 5-2

GB I-i
035-19569-101 (0109)

6 OPERATION 6-1 9 TECHNICAL DATA 9-1

6.1 Oil Heater Operation 6-1 9.1 Dimensions 9-1

6.2 Checking the Oil Level in the Oil Reservoir 6-1 9.2 Dimensions -
Evaporator Compact Water Boxes 9-4
6.3 Start-up Procedure 6-1
9.3 Nozzle Arrangements -
6.4 Chiller Operation 6-4 Evaporator Compact Water Boxes 9-5
6.5 Operating Log Sheet 6-4 9.4 Dimensions -
Condenser Compact Water Boxes 9-7
6.7 Stopping the System 6-7
9.5 Nozzle Arrangements -
6.8 Prolonged Shutdown 6-7
Condenser Compact Water Boxes 9-8
6.9 Start-up after Prolonged Shutdown 6-7
9.6 Dimensions -
Evaporator Marine Water Boxes 9-9
7 MAINTENANCE 7-1 9.8 Nozzle Arrangements -
Evaporator Marine Water Boxes 9-10
7.1 Inspections 7-1
9.8 Dimensions -
7.2 Oil Return System 7-2 Condenser Marine Water Boxes 9-11
7.3 Oil Charge 7-3 9.8 Nozzle Arrangements -
Condenser Marine Water Boxes 9-12
7.4 Refrigerant Charge 7-3
9.9 Unit Weights 9-13
7.5 Condenser and Evaporator 7-5
9.10 Process and Instrumentation Diagram 9-15
7.6 Compressor 7-7

7.7 Compressor Motor 7-7

10 SPARE PARTS 10-1
7.8 Electrical Controls 7-8

7.9 Testing Motor Winding Insulation 7-8 11 DE-COMMISSIONING, DISMANTLING AND

DISPOSAL 11-1
8 TROUBLSHOOTING 8-1 11.1 General 11-1

I-ii GB
 035-19569-101 (0109)

1 SUPPLIER INFORMATION
1.1 Introduction For warranty purposes, the following conditions must
be satisfied:
York YK chillers are manufactured to the highest design
and construction standards to ensure high performance, The initial start of the unit must be carried out by trained
reliability and adaptability to all types of air conditioning personnel from an Authorised York Service Centre.
installations.
Only genuine York approved spare parts, oils and
The units are intended for cooling water or glycol refrigerants must be used.
solutions and are not suitable for purposes other than
those specified in this manual. All the scheduled maintenance operations detailed in
this manual must be performed at the specified times
This manual and the Control System Operating by suitably trained and qualified personnel.
Instructions contain all the information required for correct
installation and commissioning of the unit, together with Failure to satisfy any of these conditions will automatically
operating and maintenance instructions. The manuals void the warranty.
should be read thoroughly before attempting to operate
or service the unit. 1.3 Safety

All procedures detailed in the manuals, including Standards for Safety

installation, commissioning and maintenance tasks
YK chillers are designed and built within an EN ISO 9001
must only be performed by suitably trained and qualified
accredited design and manufacturing organisation and,
personnel.
within the limits specified in this manual, are in conformity
with the essential health and safety requirements of the
The manufacturer will not be liable for any injury or
following European Union Directives:
damage caused by incorrect installation, commissioning,
operation or maintenance resulting from a failure to
Machinery Directive (98/37/EEC)
follow the procedures and instructions detailed in the
manuals.
Low Voltage Directive (2006/95/EC)
1.2 Warranty EMC Directive (2004/108/EC)
York International warrants all equipment and materials Pressure Equipment Directive (97/23/EEC)
against defects in workmanship and materials for one
year from initial start-up, or eighteen months from delivery 1.4 Responsibility for Safety
(whichever occurs first) unless extended warranty has
been agreed as part of the contract. Every care has been taken in the design and manufacture
of the units to ensure that they meet the safety
The warranty is limited to free replacement and shipping requirements listed in the previous paragraph. However,
of any faulty part, or sub-assembly which has failed due the individual operating or working on any machinery is
to poor quality or manufacturing errors. All claims must primarily responsible for:
be supported by evidence that the failure has occurred
within the warranty period, and that the unit has been ■ Personal safety, safety of other personnel, and the
operated within the designed parameters specified. machinery.

All warranty claims must specify the unit model, serial ■ Correct utilisation of the machinery in accordance
number and order number. with the procedures detailed in the manuals.

The unit warranty will be void if any modification to the The owner must comply with the Governmental
unit is carried out without prior written approval from Standards and Regulations for the commissioning and
York International. in-service inspections of the unit, in particular those
relating to pressure equipments.

GB 1-1
035-19569-101 (0109)

1.5 About this Manual Mechanical Strength

The unit is not designed to withstand loads or stresses
The following symbols are used in this document to alert
from adjacent equipment, pipework or structures.
the reader to areas of potential hazard.
Additional components must not be mounted on the unit.
Any such extraneous loads may cause structural failure
A Warning is given in this document to
and may result in injury to the operator, or damage to
identify a hazard which could lead to
the equipment.
personal injury. Usually an instruction will
WARNING be given, together with a brief explanation
and the possible result of ignoring the General Access
instruction. There are a number of areas and features which may
be a hazard and potentially cause injury when working
A Caution identifies a hazard which could lead with the unit unless suitable safety precautions are taken.
to damage to the machine, damage to other It is important to ensure access to the unit is restricted
equipment and/or environmental pollution. to suitably qualified persons who are familiar with the
CAUTION Usually an instruction will be given, together potential hazards and precautions necessary for safe
with a brief explanation and the possible result operation and maintenance of equipment containing
of ignoring the instruction. high temperatures, pressures and voltages.

A Note is used to highlight additional information Pressure Systems

which may be helpful to you but where there
are no special safety implications. The unit contains refrigerant vapour and liquid under
NOTE pressure, release of which can be a danger and cause
injury. The user should ensure that care is taken during
installation, operation and maintenance to avoid damage
The contents of this manual include suggested best to the pressure system. No attempt should be made
working practices and procedures. These are issued to gain access to the component parts of the pressure
for guidance only, they do not take precedence over system other than by suitably trained and qualified
the above stated individual responsibility and/or local personnel.
safety regulations.
Electrical
This manual and any other document supplied with
the unit, are the property of York which reserves all The unit must be earthed. No installation or maintenance
rights. They may not be reproduced, in whole or in part, work should be attempted on electrical equipment
without prior written authorisation from an Authorised without first switching off, isolating and locking-off the
York representative. power supplies. Work on live equipment must only be
carried-out by suitably trained and qualified personnel.
1.6 Misuse of Equipment No attempt should be made to gain access to inside of
the control panel, wiring or other electrical enclosures
Suitability for Application during normal operation of the unit.
The unit is intended for cooling water or glycol solutions
Rotating Parts
and is not suitable for purposes other than those
specified in these instructions. Any use of the equipment Motor air vent guards and drive coupling guards must
other than its intended use, or operation of the equipment be fitted at all times and not removed unless the main
contrary to the relevant procedures may result in injury power supply has been isolated.
to the operator, or damage to the equipment.
Refrigerants and Oils
The unit must not be operated outside the design limits
Refrigerants and oils used in the unit are generally
specified in this manual.
non-toxic, non-flammable and non-corrosive, and pose
no special safety hazards. Use of gloves and safety
Structural Support glasses are, however, recommended when working on
Structural support of the unit must be provided as the unit. Build up of refrigerant vapour, from a leak for
indicated in these instructions. Failure to provide proper example, does pose a risk of asphyxiation in confined or
support may result in injury to the operator, or damage enclosed spaces and attention should be given to good
to the equipment. ventilation. For more comprehensive information on
safety precautions for use of refrigerants and oils, refer
to the Materials Safety Data tables provided.

1-2 GB
 035-19569-101 (0109)

High Temperature and Pressure Cleaning

High temperature and pressure cleaning methods (e.g.
steam cleaning) should not be used on any part of the
pressure system as this may cause operation of the
pressure relief device(s). Detergents and solvents which
may cause corrosion should also be avoided.

1.8 Safety Labels

The following labels are fixed to each unit to give

instruction, or to indicate potential hazards which may
exist.

White symbol on blue background

For safe operation, read the Instructions
first

Black symbol on yellow background

Warning: This machine may start
automatically without prior warning

Black symbol on yellow background

Warning: Hot surface

Black symbol on yellow background

Warning: Safety relief valve may discharge
gas or liquid without prior warning

Black symbol on yellow background

Warning: Isolate all electrical sources of
supply before opening or removing the
cover, as lethal voltages may exist

Black symbol on yellow background

General attention symbol

GB 1-3
035-19569-101 (0109)

1.9 Material Safety Data

Refrigerant Data:
Safety Data R134a
Toxicity Low.
In contact with skin Liquid splashes or spray may cause freeze burns. Unlikely to be hazardous
by skin absorption. Thaw affected areas with water. Remove contaminated
clothing carefully — may adhere to skin in case of freeze burns. Wash
affected areas with plenty of warm water. If symptoms occur (irritation or
blistering) obtain medical attention.
In contact with eyes Vapour has no effect. Liquid splashes or spray may cause freeze burns.
Immediately irrigate with eyewash solution or clean water for at least 10
minutes. Obtain immediate medical attention.
Ingested Highly unlikely to occur — but should this occur freeze burn will occur. Do not
induce vomiting. Provided patient is conscious, wash mouth with water and
give about 250 ml (0.5 pint) to drink. Obtain immediate medical attention.
Inhalation High atmospheric concentrations may have an anaesthetic effect, including
loss of consciousness. Very high exposures may cause an abnormal heart
rhythm and prove suddenly fatal.
At higher concentration there is a danger from asphyxiation due to reduced
oxygen content of atmosphere. Remove patient to fresh air, keep warm and
at rest. Administer oxygen if necessary. Apply artificial respiration if breathing
has ceased or shows signs of failing. In event of cardiac arrest apply external
cardiac massage. Obtain immediate medical attention.
Further medical advice Symptomatic and supportive therapy is indicated. Cardiac sensitisation has
been described which may, in the presence of circulating catecholamines
such as adrenalin, give rise to cardiac arrhythmia’s and subsequent arrest
following exposure to high concentrations.
Long term exposure A lifetime inhalation study in rats has shown that exposure to 50,000 ppm
resulted in benign tumours of the testis. This is not considered to be of
relevance to humans exposed to concentrations at or below the occupational
exposure limit.
Occupational exposure limits Recommended limit: 1000 ppm v/v - 8 hr TWA.
Stability Not specified.
Conditions to avoid Use in presence of naked flames, red hot surfaces and high moisture
levels.
Hazardous reactions May react violently with sodium, potassium, barium and other alkali and
alkaline earth metals. Incompatible materials: Magnesium and alloys
containing more then 2% magnesium.
Hazardous decomposition products Halogen acids by thermal decomposition and hydrolysis.
General precautions Avoid inhalation of high concentrations of vapours. Atmospheric
concentrations should be minimised and kept as low as reasonably
practicable below the occupational exposure limit. The vapour is heavier than
air and collects at low level and in confined areas. Ventilate by extraction
at lowest levels.
Respiratory protection Where doubt exists on atmospheric concentration, approved breathing
apparatus should be worn. This should be self contained or of the long
breather type.
Storage Keep containers dry and in a cool place away from fire risk, direct sunlight,
and all sources of heat such as radiators. Keep at temperatures not
exceeding 45°C.
Protective clothing Wear overalls, impervious gloves and goggles/face protection.

1-4 GB
 035-19569-101 (0109)

Spill/leak procedure Ensure suitable personal protective clothing and respiratory protection is
worn. Provided it is safe to do so, isolate the source of the leak. Allow small
spillage’s to evaporate provided there is suitable ventilation.
Large spillage’s: Ventilate area. Contain spillage’s with sand, earth or
any suitable absorbent material. Prevent liquid from entering drains,
sewers, basements and work pits since vapour may create a suffocating
atmosphere.
Disposal Best to recover and recycle. If this is not possible, destruction is to be in
an approved facility which is equipped to absorb and neutralise acids and
other toxic processing products.
Fire extinguishing data Non-flammable at atmospheric conditions.
Containers Fire exposed containers should be kept cool with water sprays. Containers
may burst if overheated.
Fire fighting protective equipment Self contained breathing apparatus and protective clothing must be worn
in fire conditions.

Refrigerant Oil Data

Safety Data York "K" Oil
Classification Non-hazardous
In contact with skin Minimally irritating. No first aid necessary. Exercise reasonable personal
cleanliness including cleansing exposed skin areas several times daily with
soap and water. Launder soiled work clothes at least weekly.
In contact with eyes Flush eyes with eyewash solution or clean water for 15 minutes and consult
a physician.
Ingested May cause nausea and diahorrhea. Obtain immediate medical attention.
Inhalation If oil mist is inhaled, remove to fresh air and consult a physician.
Occupational exposure limits Not determined.
Stability Stable but hygroscopic - store in sealed containers.
Conditions to avoid Strong oxidisers, caustic or acid solutions, excessive heat. May degrade
some paints and rubber materials.
Hazardous decomposition Not fully, Analogous compounds evolve carbon monoxide, carbon dioxide
and other unidentified fragments when burned. Burning may evolve irritating/
noxious fumes.
Respiratory protection Use in well ventilated areas - ventilate locally.
Protective clothing Goggles or face shield should be worn. Gloves not necessary, but
recommended, especially for prolonged exposure.
Spill / Leak procedure Wear suitable protective equipment. Especially goggles. Stop source of
spill. Use absorbent materials to soak up fluid (i.e. sand, sawdust and
commercially available materials).
Disposal Incinerate the oil and all associated wastes in an approved facility in
accordance with local laws and regulations governing oily wastes.
Fire extinguishing data Flash point over 300°C. Use dry chemical, carbon dioxide or foam. Spraying
water on hot or burning liquid may cause frothing or splashing.
If a leak or spill has not ignited use water spray to disperse the vapours and
to provided protection for persons attempting to stop the leak.
Containers Fire exposed containers should be kept cool with water sprays.
Fire fighting protective equipment Self contained breathing apparatus should be worn in fire conditions.

GB 1-5
035-19569-101 (0109)

Thermal & Acoustic Materials Data

Health Hazard & First Aid Toxicity Index <10 to NES713 Issue 3 (1991): Non-hazardous, non-toxic.
No first aid necessary.
Stability / Reactivity Stable.
Handling / Use / Disposal No special handling precautions required. Dispose of according to local
laws and regulations governing non-biodegradable non-hazardous solid
wastes.
Fire & Explosion Flammability rating Class 1 to BS 476 pt 7: Non-flammable. If forced to
burn, combustion products are typically over 95% carbon dioxide and
carbon monoxide.

1-6 GB
 035-19569-101 (0109)

2 PRODUCT DESCRIPTION

Figure 2.1 YK Centrifugal Liquid Chiller (Front View)

2.1 General (Figures 2.1 and 2.2) In operation, a liquid (water or brine to be chilled) flows
through the evaporator, where boiling refrigerant absorbs
The York YK Millennium™ Centrifugal Liquid Chiller is heat from the liquid. The chilled liquid is then piped to fan
primarily used for large air conditioning systems, but may coil units or other air conditioning terminal units, where
be used on other applications. The chiller is completely it flows through finned coils, absorbing heat from the
factory-packaged including evaporator, condenser, air. The warmed liquid is then returned to the chiller to
compressor, motor, lubrication system, graphic control complete the chilled liquid circuit.
centre (OptiView), and all interconnecting unit piping
and wiring. The initial charge of refrigerant and oil is The refrigerant vapour, which is produced by the boiling
supplied for each unit. action in the evaporator, flows to the compressor
where the rotating impeller increases its pressure and
The chiller is controlled by a modern state of the art temperature and discharges it into the condenser.
microprocessor control centre that monitors its operation. Water flowing through the condenser tubes absorbs
The control centre is programmed by the operator to suit heat from the refrigerant vapour, causing it to condense.
job specifications. Automatic timed start-ups and shut- The condenser water is supplied to the chiller from an
downs are also programmable to suit nighttime, week- external source, usually a cooling tower. The condensed
ends, and holidays. The operating status, temperatures, refrigerant drains from the condenser into the liquid
pressures, and other information pertinent to operation return line, where the variable orifice meters the flow
of the chiller are automatically displayed and read on of liquid refrigerant to the evaporator to complete the
a graphic display. Other displays can be observed by refrigerant circuit.
pressing the keys as labelled on the control centre.
The chiller with the graphic control centre (OptiView) is The major components of a chiller are selected to handle
compatible with an electro-mechanical starter, YORK the refrigerant, which would be evaporated at full load
Solid State Starter (optional), or Variable Speed Drive design conditions. However, most systems will be called
(optional). upon to deliver full load capacity for only a relatively small
part of the time the unit is in operation.

GB 2-1
035-19569-101 (0109)

2.2 Capacity Control (Figure 2.2)

The major components of a chiller are selected for full

load capacities, therefore capacity must be controlled
to maintain a constant chilled liquid temperature leaving
the evaporator. Prerotation vanes (PRV), located at the
entrance to the compressor impeller, compensate for
variation in load (See Detail A).

The position of these vanes is automatically controlled

through a lever arm attached to an electric motor
located outside the compressor housing. The automatic
adjustment of the vane position in effect provides the
performance of many different compressors to match
various load conditions from full load with vanes wide
open to minimum load with vanes completely closed.

Figure 2.2 YK Refrigerant Flow Diagram

2-2 GB
 035-19569-101 (0109)

Figure 2.3 YK Centrifugal Liquid Chiller (Rear View)

2.3 Compressor 2.4 Compressor Lubrication System

(Figure 2.4)
The compressor is a single-stage centrifugal type
powered by an open-drive electric motor. The chiller lubrication system consists of the oil pump,
oil filter, oil cooler and all interconnecting oil piping and
The rotor assembly consists of a heat-treated alloy steel passages. The main points within the compressor which
drive shaft and impeller shaft with a cast aluminum, must be supplied with forced lubrication:
fully shrouded impeller. The impeller is designed for
balanced thrust and is dynamically balanced and over- 1. Compressor Drive Shaft (Low Speed)
speed tested.
a. Shaft seal.
The inserted type journal and thrust bearings are b. Front and rear journal bearings –
fabricated of aluminum alloy. Single helical gears with one on each side of driving gear.
crowned teeth are designed so that more than one tooth c. Low speed thrust bearing
is in contact at all times. Gears are integrally assembled (forward and reverse).
in the compressor rotor support and are film lubricated.
Each gear is individually mounted in its own journal and 2. Compressor Driven Shaft (High Speed)
thrust bearings.
a. Forward and reverse high speed thrust
The open-drive compressor shaft seal is a double bellows bearing.
cartridge style with ceramic internal and atmospheric
b. Two journal bearings.
seal faces. The seal is oil-flooded at all times and is
pressure-lubricated during operation.
3. Speed Increasing Gears

a. Meshing surfaces of drive and pinion gear

teeth.

GB 2-3
035-19569-101 (0109)

Figure 2.4 Compressor Lubrication System

2-4 GB
 035-19569-101 (0109)

To provide the required amount of oil under the necessary a motor support.
pressure to properly lubricate these parts, a motor driven
submersible oil pump is located in a remote oil sump. Motor drive shaft is directly connected to the compressor
shaft with a flexible disc coupling. This coupling has
Upon pressing of the COMPRESSOR START switch on all metal construction with no wearing parts to assure
the control panel, the oil pump is immediately energized. long life, and no lubrication requirements to provide low
After a 50 second pre-lube period, the compressor motor maintenance.
will start. The oil pump will continue to run during the
entire operation of the compressor, and for 150 seconds For units utilising remote electro-mechanical starters,
during compressor shutdown. a terminal box is provided for field connected conduit.
Motor terminals are brought through the motor casing into
The submerged oil pump takes suction from the the terminal box. Jumpers are furnished for three-lead
surrounding oil and discharges it to the oil cooler where type of starting. Motor terminal lugs are not furnished.
heat is rejected. The oil flows from the oil cooler to the oil Overload/overcurrent transformers are furnished with
filter. The oil leaves the filter and flows to the emergency all units.
oil reservoir where it is distributed to the compressor
bearings. The oil lubricates the compressor rotating For units furnished with factory packaged Solid State
components and is returned to the oil sump. Starters, (optional) see Options Section.

There is an emergency oil reservoir located at the 2.6 Graphic Control Centre (OptiView)
highest point in the lubrication system internally in the
compressor. It provides an oil supply to the various The graphic control centre is factory-mounted, wired
bearings and gears in the event of a system shutdown and tested. The electronic panel automatically controls
due to power failure. The reservoir, located on the top of the operation of the unit in meeting system cooling
the compressor, allows the oil to be distributed through requirements while minimizing energy usage. For
the passages by gravity flow, thus providing necessary detailed information on the Graphic Control Centre, refer
lubrication during the compressor shutdown. to Form 160.54-O1

2.4.1 Oil Pump 2.7 Heat Exchangers

For normal operation, the oil pump should operate at all
Evaporator and condenser shells are fabricated from
times during chiller operation.
rolled carbon steel plates with fusion welded seams.
Heat exchanger tubes are internally enhanced type.
On shutdown of the system for any reason, the oil pump
operates and continues to run for 150 seconds. The
system cannot restart during that time interval.
2.7.1 Evaporator
The evaporator is a shell and tube, flooded type heat
2.4.2 Oil Heater exchanger. A distributor trough provides uniform
distribution of refrigerant over the entire shell length.
During long idle periods, the oil in the compressor oil
Stainless steel mesh eliminators or suction baffles
reservoir tends to absorb as much refrigerant as it can
are located above the tube bundle to prevent liquid
hold, depending upon the temperature of the oil and
refrigerant carryover into the compressor. A 2" liquid
the pressure in the reservoir. As the oil temperature
level sight glass is located on the side of the shell to aid
is lowered, the amount of refrigerant absorbed will be
in determining proper refrigerant charge. The evaporator
increased. If the quantity of refrigerant in the oil becomes
shell contains dual refrigerant relief valves.
excessive, violent oil foaming will result as the pressure
within the system is lowered on starting. This foaming is
caused by refrigerant boiling out of the oil as the pressure
2.7.2 Condenser
is lowered. If this foam reaches the oil pump suction, the The condenser is a shell and tube type, with a discharge
bearing oil pressure will fluctuate with possible temporary gas baffle to prevent direct high velocity impingement
loss of lubrication, causing the oil pressure safety cutout on the tubes. A separate subcooler is located in the
to actuate and stop the system (Refer to Control Centre condenser to enhance performance. Dual refrigerant
Manual 160.54.OI). relief valves are located on condenser shells with
optional isolation refrigerant isolation valves.
2.5 Compressor Motor
The compressor motor is an open-drip-proof, squirrel
2.7.3 Water Boxes
cage, induction type constructed to York design The removable compact water boxes are fabricated of
specifications, 50 hertz motors operate at 2975 rpm. steel. The design working pressure is 1034 kPa and the
boxes are tested at 1551 kPa. Integral steel water baffles
The open motor is provided with a D-flange, cast iron provide the required pass arrangements.
adapter mounted to the compressor and supported by

GB 2-5
035-19569-101 (0109)

Stub-out water nozzle connections with Victaulic grooves 2.9 Options and Accessories
are welded to the water boxes. These nozzle connections
are suitable for Victaulic couplings, welding or flanges, 2.9.1 Service Isolation Valves
and are capped for shipment. Plugged ¾" drain and vent
If the chiller is equipped with optional service isolation
connections are provided in each water box.
valves on the discharge and liquid line, these valves
must remain open during operation. These valves are
2.8 Refrigerant Flow Control
used for isolating the refrigerant charge in either the
evaporator or condenser to allow service access to the
Refrigerant flow to the evaporator is controlled by a
system. A refrigerant pump-out unit will be required to
variable orifice.
isolate the refrigerant.
A level sensor senses the refrigerant level in the condenser
Isolation of the refrigerant in this system must be
and outputs an analog voltage to the microprocessor
performed by a qualified service technician.
that represents this level (0% = empty; 100% = full).
Under program control, the microprocessor modulates
2.9.2 Hot Gas Bypass
a variable orifice to control the condenser refrigerant
level to a programmed setpoint. Other setpoints affect Hot gas bypass is optional and is used to eliminate
the control sensitivity and response. These setpoints compressor surge during light load or high head
must be entered at chiller commissioning by a qualified operation. The control panel will automatically modulate
service technician. Only a qualified service technician the hot gas valve open and closed as required.
may modify these settings. Adjustment of the hot gas control valve must be
performed by a qualified service technician following
While the chiller is shut down, the orifice will be in the Hot Gas Set-up procedure.
the fully open position causing the sensed level to be
approximately 0%. When the chiller is started, after the Changes in chilled water flow will require re-adjustment
vane motor end switch (VMS) opens when entering of the hot gas control to insure proper operation.
SYSTEM RUN, if actual level is less than the level
setpoint, a linearly increasing ramp is applied to the 2.9.3 Solid State Starter
level setpoint. This ramp causes the setpoint to go from
The optional Solid State Starter is a reduced voltage
the initial refrigerant level (approximately 0%) to the
starter that controls and maintains a constant current
programmed setpoint over a period of 15 minutes.
flow to the motor during start-up. It is mounted on the
chiller. Power and control wiring between the starter and
If the actual level is greater than the setpoint when the
chiller are factory installed. Available for 380-600 volts,
VMS opens, there is no pulldown period, it immediately
the starter enclosure is IP54 with a hinged access door
begins to control to the programmed setpoint.
with lock and key. Electrical lugs for incoming power
wiring are provided.
While the chiller is running, the refrigerant level is
normally controlled to the level setpoint. However,
anytime the vanes fully close (VMS closes), normal
2.9.4 Variable Speed Drive
level control is terminated, any refrigerant level setpoint An optional 400V – 3-Ph – 60/50Hz Variable Speed Drive
pulldown in effect is cancelled and the outputs to the level can be factory packaged with the chiller. It is designed to
control will be opposite that which is supplied to the vane vary the compressor motor speed and pre-rotation vane
motor (i.e., when a close pulse is applied to the vane position by controlling the frequency and voltage of the
motor, an open pulse is applied to the level control, etc.). electrical power to the motor. Operational information
When the VMS opens, if the refrigerant level is less than is contained in Form 160.00-O1 (VSD 658 HP and 900
the level setpoint, a refrigerant level setpoint pulldown HP) or 160.00-O4 (VSD OptiSpeed 292 HP and 419
is initiated as described above. Otherwise, the level is HP). The control logic automatically adjusts motor speed
controlled to the programmed setpoint. and compressor pre-rotation vane position for maximum
part load efficiency by analysing information fed to it by
sensors located throughout the chiller.

The VSD eliminates the need for a starter and has a

soft starting characteristic that never exceeds 100%
full load amps. It also provides automatic power factor
correction.

An optional harmonic filter limits electrical power supply

distortion from the variable speed drive and further
improves power factor correction.

2-6 GB
 035-19569-101 (0109)

2.10 Nomenclature

YK ER ER Q7 5 CS G S
Model Special Modifications

Evaporator Code Design Level

Condenser Code Motor Code

Compressor Code Power Supply (5 for 50 Hz)

GB 2-7
035-19569-101 (0109)

2.11 Range of Models

COMPRESSOR EVAPORATOR CONDENSER
MOTOR CODES
CODE CODE CODE
Q3 AP to AS AP to AS
CP to CS CP to CS
Q3, Q4 5CC-5CO
DP to DS DP to DS
Q4 EP to ET EP to ET
CP to CS CP to CS
Q5
DP to DS DP to DS
5CE-5CO
EP to ET EP to ET
Q5, Q6, Q7
FQ to FT FQ to FT
EP to ET EP to ET
P7 5CP-5CU
FQ to FT FQ to FT
P8 GQ to GS EV to EX
HQ to HS FV to FX
5CE-5CU
P8, P9 JP to JS JP to JS
LQ to LS LQ to LS
KP to KS, K2 to K4 KP to KS, K2 to K4
H9 5CK-5CW
MQ to MS, M2 to M4 MQ to MS, M2 to M4
K1 KT to KX, K5 to K7 KP to KS, K2 to K4
MQ to MS, M2 to M4 MQ to MS, M2 to M4
NQ to NS, N2 to N4 NP to NS, N2 to N4 5CN-5DC
K1, K2
PQ to PS, P2 to P4 PQ to PS, P2 to P4
QQ to QS, Q2 to Q4 QQ to QS, Q2 to Q4
NQ to NS, N2 to N4 NP to NS, N2 to N4
K3 QQ to QS, Q2 to Q4 QQ to QS, Q2 to Q4 5DA-5DH
RQ, RS, RV, R3, R5, R7 RQ to RS, R2 to R4
RP, RR, RT, R2, R4, R6 RQ to RS, R2 to R4
SQ to SS, S2 to S4
SQ, SS, SV, S3, S5, S7
K4 VP to VS, V2 to V5 5DA-5DJ
TP to TS, T2 to T5
XQ to XS, X2 to X4
XQ to XS, X2 to X4
WP to WT, W2, W4, W6 WQ to WS, W1 to W4
K7 5DD-5DL
ZQ to ZS, Z1 to Z4 ZQ to ZS, Z1 to Z4

2-8 GB
 035-19569-101 (0109)

3 TRANSPORTATION, RIGGING AND STORAGE

3.1 General 8. Do not run hot water (40°C maximum.) or steam

through the evaporator or condenser at any time.
YK units are shipped as a single factory assembled,
piped, wired package, requiring minimum installation 3.2 Shipment
to make chilled water connections, condenser water
connections, refrigerant atmospheric relief connections, The chiller may be ordered and shipped in any of the
and electrical power connections. following forms:

Refrigerant and oil charges are shipped separately Form 1 – Factory Assembled Unit (complete with
(unless optional condenser isolation valves are motor, refrigerant and oil charges)
ordered).
1. The motor/compressor assembly mounted, with
Chillers can also be shipped dismantled when required all necessary interconnecting piping assembled.
by rigging conditions, but generally it is more economical Graphic control centre (OptiView) is mounted on the
to enlarge access openings to accommodate the factory unit. Complete unit factory leak tested, evacuated
assembled unit. Chillers shipped dismantled MUST and charged with R134a.
be field assembled under the supervision of a York
representative. An optional Solid State Starter or Variable Speed
Drive can be factory mounted and wired.
FIELD ASSEMBLED UNITS ONLY
2. Miscellaneous material – Four (4) vibration isolation
Use Form 160.73-N3 in conjunction with this manual. pads (or optional spring isolators and brackets).
This instruction will be furnished with all units that are to
be field assembled. Extra copies may be ordered from Form 2 – Factory Assembled Unit (complete with
the York Publication Distribution Centre. motor, refrigerant and oil charges shipped separately).

A York authorised representative must check the 1. The motor/compressor assembly mounted, with
installation, supervise the initial start-up and operation all necessary interconnecting piping assembled.
of all newly installed chillers. Graphic control centre (OptiView) is mounted on the
unit. Complete unit factory leak tested, evacuated
The York Warranty may be voided if the and charged with holding charge of nitrogen.
following restrictions are not adhered to:
An optional Solid State Starter or Variable Speed
CAUTION Drive can be factory mounted and wired.

2. Miscellaneous material – Four (4) vibration isolation

1. No valves or connections should be opened under
pads (or optional spring isolators and brackets).
any circumstances because such action will result in
loss of the factory nitrogen charge.
Form 3 – Driveline Separate From Shells
2. Do not dismantle or open the chiller for any
Shipped as three major assemblies. Unit first
reason except under the supervision of a York
factory assembled, refrigerant piped, wired and leak
representative.
tested; then dismantled for shipment. Compressor/
motor assembly removed from shells and skidded.
3. When units are shipped dismantled, notify the nearest
Evaporator/condenser shells are not skidded.
York office in ample time for a York representative
to supervise rigging the unit to its operating position
All compressor wiring attached, and all conduit is left
and the assembly of components.
on shell. All openings on compressor, oil separator,
and shell are closed and charged with dry nitrogen
4. Do not make final power supply connections to the
(1.4 to 2 kPag).
compressor motor or control centre.
Miscellaneous packaging of control centre, tubing,
5. Do not charge the compressor with oil.
water temperature controls, wiring, oil, isolators, solid
state starter (option), etc.; refrigerant charge shipped
6. Do not charge the unit with refrigerant.
separately.
7. Do not attempt to start the system.

GB 3-1
035-19569-101 (0109)

Units shipped dismantled MUST be re- 3.3 Inspection, Damage and Shortage
assembled by, or under the supervision of, a
York representative. (See Form 160.73-N3) The unit shipment should be checked on arrival to see
NOTE that all major pieces, boxes and crates are received.
Each unit should be checked before unloading, for any
Form 7 – Split Shells visible signs of damage. Any damage or signs of possible
damage must be reported to the transportation company
Shipped as four major assemblies. Unit first factory immediately for their inspection.
assembled, refrigerant piped, wired and leak tested;
then dismantled for shipment. Compressor/motor York will not be responsible for any damage in shipment
assembly removed from shells and skidded. or at job site or loss of parts.

Evaporator and condenser shells are separated at When received at the job site all containers should
tube sheets and are not skidded. Refrigerant lines be opened and contents checked against the packing
between shells are flanged and capped, requiring no list. Any material shortage should be reported to York
welding. immediately.

All compressor wiring attached. All wiring harnesses Chiller Data Plate
on shells are removed. All openings on compressor
and shells are closed and charged with dry nitrogen A unit data plate is mounted on the control panel
(1.4 to 2 kPag). assembly of each unit, giving unit model number; design
working pressure; water passes; refrigerant charge;
Miscellaneous packaging of control centre, tubing, serial numbers; and motor power characteristics and
water temperature controls, wiring, oil isolators, solid connection diagrams.
state starter (option), etc.; refrigerant charge shipped
separately. Additional information may be found on the motor
data plate. This information should be included when
Units shipped dismantled MUST be re- contacting the factory on any problem relating to the
assembled by, or under the supervision of, a motor.
York representative. (See Form 160.73-N3)
NOTE

When more than one chiller is ordered, the major

parts of each unit will be marked to prevent mixing
of assemblies. (Piping and Wiring Drawings will be
furnished by York.)

3-2 GB
 035-19569-101 (0109)

3.4 Rigging Do not lift the unit with slings around motor/
compressor assembly or by means of eye
The complete standard chiller is shipped without skids. bolts in the tapped holes of the compressor
(When optional skids are used it may be necessary to CAUTION motor assembly. Do not turn a unit on its side
remove the skids so riggers skates can be used under for rigging. Do not rig vertically.
the unit end sheets to reduce overall height.)
The rigging and operating weights and overall dimensions
Each unit has four (4) lifting holes (two in each end) in are given in Section 9 as a guide in determining the
the end sheets which should be used to lift the unit. clearances required for rigging. (Add 150 mm to overall
height for optional skidded unit.).
Care should be taken at all times during rigging and
handling of the chiller to avoid damage to the unit and
its external connections. Lift only using holes shown.

Figure 3.1 . Rigging

GB 3-3
035-19569-101 (0109)

Page Left Intentionally Blank

3-4 GB
 035-19569-101 (0109)

4 INSTALLATION 4.5 Rigging Unit to Final Location

Rig the unit to its final location on the floor or mounting

4.1 Location
pad, lift the unit (or shell assembly) by means of an
YK units are furnished with vibration isolator mounts overhead lift and lower the unit to its mounting position.
for basement or ground level installations. Units may (If optional shipping skids are used, remove them before
be located on upper floor levels providing the floor is lowering the chiller to its mounting position.)
capable of supporting the total unit operating weight and
At this point units shipped dismantled should
optional spring isolators are used.
be assembled under the supervision of a York
Sufficient clearance to facilitate normal service and representative.
NOTE
maintenance work must be provided all around and
above the unit and particularly space provided at either
end to permit cleaning or replacement of evaporator and If evaporator is to be field insulated, the insulation should
condenser tubes – see Clearances. be applied to the evaporator before the unit is placed in
position while the unit is in the lift position. Be sure unit
A doorway or other sufficiently large opening properly is properly supported. (See INSULATION).
located may be used. The chiller should be located in
an indoor location where temperatures range from 4.4°C 4.6 Locating and Installing Isolator Pads
to 43.3°C.
The isolator pad mounts are to be located as shown in
The unit should not be installed directly Figure .1
on flammable materials, such as wooden
structures or roof’s. After the isolator pads have been placed into position
WARNING on the floor, lower the chiller onto the pads. When the
unit is in place, remove the rigging equipment and check
that the unit is level both longitudinally and transversely.
4.2 Motors
The unit should be level within 6 mm from one end to the
The YK open motor is air cooled. Check national, local other end and from front to the rear. If the chiller is not
and other codes for ventilation requirements. level within the amount specified, lift it and place shims
between the isolation pad and the chiller tube sheets.
(Shims furnished by the installer.) Lower unit again and
4.3 Foundation
recheck to see that it is level.
A level floor, mounting pad or foundation must be
Checking the Isolation Pad Deflection
provided by others, capable of supporting the operating
weight of the unit.
All isolation pads should be checked for the proper
deflection while checking to see if the unit is level. Each
To be in conformity with the EN 60204 standard,
pad should be deflected approximately 4 mm. If an
it can be necessary to add a service platform
isolation pad is under-deflected, shims should be placed
so that the height of the control handles (i.e.
between the unit tube sheet and the top of the pad to
NOTE circuit breaker handle) lies between 0,6 m and
equally deflect all pads.
1,9 m.
Levelling the Unit

4.4 Clearances The longitudinal alignment of the unit should be checked

by placing a level on the top centre of the evaporator
Clearances should be adhered to as follows: shell under the compressor/motor assembly. Transverse
alignment should be checked by placing a level on top
Rear and above unit – 610 mm.
of the shell end sheets at each end of the chiller.
Front of unit – 910 mm.

Tube Removal– 4300 mm except those shell codes

detailed below:
Evaporator Condenser Tube Removal (mm)
Code Code (either end)
Q, N, R, X, Q, N, R, T, X, 4900
S, Z S, V, Z 5500
W W 6700

GB 4-1
035-19569-101 (0109)

4.7 Installing Optional Spring Isolators 4.8 Piping Connections

When ordered, 4 spring type isolator assemblies will be After the unit is levelled (and wedged in place for optional
furnished with the unit. The 4 assemblies are identical spring isolators) the piping connections may be made;
and can be placed at any of the 4 corners of the unit. chilled water, condenser water and refrigerant relief. The
piping should be arranged with offsets for flexibility, and
While the unit is still suspended by the rigging, the adequately supported and braced independently of the
isolators should be bolted to the unit by inserting the cap unit to avoid strain on the unit and vibration transmission.
screw(s) through the hole(s) in the mounting bracket into Hangers must allow for alignment of pipe. Isolators (by
the tapped hole in the top of the isolator levelling bolt(s). others) in the piping and hangers are highly desirable,
Then the unit can be lowered onto the floor. and may be required by specifications, in order to
effectively utilise the vibration isolation characteristics
The levelling bolts should now be rotated one (1) turn of the vibration isolation mounts of the unit.
at a time, in sequence, until the unit end sheets are
clear of the floor by the dimension shown in Figure .2 Check for piping alignment – Upon completion of piping,
and the unit is level. Check that the unit is level, both a connection in each line as close to the unit as possible
longitudinally and transversely (see Levelling the Unit). should be opened, by removing the flange bolts or
If the levelling bolts are not long enough to level unit coupling and checked for piping alignment. If any of the
due to an uneven or sloping floor or foundation, steel bolts are bound in their holes, or if the connection springs
shims (grouted, if necessary) must be added beneath are out of alignment, the misalignment must be corrected
the isolator assemblies as necessary. by properly supporting the piping or by applying heat to
anneal the pipe.
After the unit is levelled, wedge and shim under each
corner to solidly support the unit in this position while If the piping is annealed to relieve stress, the
piping connections are being made, pipe hangers inside of the pipe must be cleaned of scale
adjusted and connections checked for alignment. Then before it is finally bolted in place.
the unit is filled with water and checked for leaks. The NOTE

levelling bolts should now be finally adjusted until the

wedges and shims can be removed. The unit should now 4.9 Evaporator and Condenser Water Piping
be in correct level position, clear of the floor or foundation
and without any effect from the weight of the piping. The evaporator and condenser liquid heads have
nozzles which are grooved, suitable for welding 1034
kPa DWP flanges or the use of Victaulic couplings.
Factory mounted flanges are optional.

The nozzles and water pass arrangements are delivered

in accordance with the job requirements (see Product
Drawings delivered with the job and Section 9). Standard
units are designed for 1034 kPa DWP on the water side.
If job requirements are for greater than 1034 kPa DWP,
check the unit Data Plate before applying pressure to
evaporator or condenser to determine if the chiller has
provisions for the required DWP.

Inlet and outlet connections are identified by labels

placed adjacent to each nozzle.

4-2 GB
 035-19569-101 (0109)

LD08525

UNIT WEIGHT UP TO 7423 Kgs. UNIT WEIGHT 7424 TO 13,080 Kgs.

LD08527 LD08528

UNIT WEIGHT 13,081 TO 24,281 Kgs. UNIT WEIGHT 24,281 TO 45,570 Kgs.

Condenser See
Centreline Centreline Dimensions
of Vessels

Evaporator
Centreline

See
Dimensions

Figure 4.1 Neoprene Isolators

GB 4-3
035-19569-101 (0109)

4-Spring Isolators, Unit Weights less than 15880 kg

6-Spring Isolators, Unit Weights 15881 kg to 26467 kg

9-Spring Isolators, Unit Weights greater than 26468 kg

Figure 4.2 Spring Isolators

4-4 GB
 035-19569-101 (0109)

4.9.1 Chilled Water Circuit 4.9.2 Condenser Water Circuit

Foreign objects which could lodge in, or block flow For proper operation of the unit, condenser refrigerant
through the evaporator and condenser tubes must be pressure must be maintained above evaporator pressure.
kept out of the water circuit. All water piping must be If operating conditions will fulfill this requirement, no
cleaned or flushed before being connected to the chiller attempt should be made to control condenser water
pumps, or other equipment. temperature by means of automatic valves, cycling of
the cooling tower fan or other means, since chillers are
Permanent strainers (supplied by others) are required designed to function satisfactorily and efficiently when
in both the evaporator and condenser water circuits to condenser water is allowed to seek its own temperature
protect the chiller as well as the pumps, tower spray level at reduced loads and off-peak seasons of the
nozzles, chilled water coils and controls, etc. The year. However, if entering condenser water temperature
strainer should be installed in the entering chilled water can go below the required minimum, condenser water
line, directly upstream of the chiller. temperature must be maintained equal to or slightly
higher than the required minimum. Refer to Figure 4.3
Water piping circuits should be arranged so that the for a typical water piping schematic.
pumps discharge through the chiller, and should be
controlled as necessary to maintain essentially constant
chilled and condenser water flows through the unit at all
load conditions.

If pumps discharge through the chiller, the strainer may

be located upstream from pumps to protect both pump
and chiller. (Piping between strainer, pump and chiller
must be very carefully cleaned before start-up.) If pumps
are remotely installed from chiller, strainers should be
located directly upstream of the chiller.

Figure 4.3 Schematic of a Typical Piping Arrangement

GB 4-5
035-19569-101 (0109)

4.10 Stop Valves transit may cause the nuts to loosen. If water pressure
is applied before tightening is done, the gaskets may be
Stop valves may be provided (by others) in the damaged and have to be replaced.
evaporator and condenser water piping adjacent to
the unit to facilitate maintenance. Thermometer wells Fill the chilled and condenser water circuits, operate
and pressure taps should be provided (by others) in the pumps manually and carefully check the evaporator
the piping as close to the unit as possible to facilitate and condenser water heads and piping for leaks. Repair
operating check. leaks as necessary.

4.11 Flow Switches (Field Installed) Before initial operation of the unit both water circuits
should be thoroughly vented of all air at the high
A flow switch or pressure differential control in the chilled points.
or condensed water lines is an accessory furnished for
connection to the control panel. If a flow switch is used, 4.14 Refrigerant Relief Piping
it must be directly in series with the chiller and sensing
only water flow through the chiller. The flow switch can Each unit is equipped with pressure relief valves located
be paddle type (field installed) or thermal type (factory on the condenser and on the evaporator for the purpose
mounted). A differential pressure switch that senses of quickly relieving excess pressure of the refrigerant
pressure drop across the unit can also be supplied. charge to the atmosphere as a safety precaution in case
of an emergency, such as fire. The pressure relief valve
4.12 Drain and Vent Valves is set at design pressure of the system and has discharge
capacity required by relevant standard.
Drain and vent valves (by others) should be installed
in the connections provided in the evaporator and Refrigerant relief vent piping (by others), from the relief
condenser liquid heads. These connections may be valves to the outside of the building, is required by code
piped to drain if desired. in most areas and should be installed on all chillers. The
vent line should be sized in accordance with EN13136,
4.13 Checking Piping Circuits and Venting Air or local code. The vent line must include a dirt trap in
the vertical leg to intercept and permit clean out and to
After the water piping is completed, but before any trap any vent stack condensation. The piping MUST be
water box insulation is applied. Tighten and torque (to arranged to avoid strain on the relief valves, using a
maintain between 41 and 82 Nm) the nuts on the liquid flexible connection, if necessary.
head flanges. Gasket shrinkage and handling during

Figure 4.4 Typical Refrigerant Vent Piping

4-6 GB
 035-19569-101 (0109)

4.15 Unit Piping 4.17 Control Wiring

Compressor lubricant piping and system external piping On units shipped disassembled, after installation of the
are factory installed on all units shipped assembled. control panel, control wiring must be completed between
On units shipped dismantled, the lubricant piping to oil unit components and control panel, solid state starter, or
sump and oil cooler and system oil return connections variable speed drive, when used, using wiring harness
should be completed, under the supervision of the York furnished. Refer to Form 160.73-N3.
representative, using material furnished. See Form
160.73-N3. Field wiring connections for control modifications (by
others) if required, are shown on Form 160.73-PW7.
4.16 Control Panel Positioning
(See Figure 4.5) No deviations in unit wiring from that shown on drawings
delivered shall be made without prior approval of the
On units with H9 and K1-K7 compressors, the control York representative.
panel is placed in a position above the evaporator for
shipping. For units with P and Q compressors the control 4.18 Power Wiring
panel is not adjustable. To move the control panel into
position for operation, proceed as follows: Chiller with Electro-Mechanical Starter

1. While supporting the control panel, remove the A 115 V, 1 Ø, 50 Hz supply of 15 amperes must be
hardware between the support arms and the supplied to the control panel, from the control transformer
evaporator. (2 kVA required) included with the compressor motor
starter. DO NOT make final power connections to control
2. Swing the control panel into a vertical position. centre until approved by York representative.

3. Slide the control panel down the guide rails to the Oil Pump – 3 Phase Starter
proper position. Tighten securely.
Separate wiring or a fused disconnect switch should be
4. Discard unused hardware. supplied by the installer.

Remote Electro-Mechanical Starter

Remote Electro-Mechanical starters for the

chiller must be furnished in accordance with
York Standard R-1051 (Product Drawing
CAUTION Form 160.45-PA5.1) to provide the features
necessary for the starter to function properly
with the York control system.

Each unit is furnished for a specific electrical power

supply as stamped on the Unit Data Plate, which also
details the motor connection diagrams.

To insure proper motor rotation the starter power

input and starter to motor connections must be
checked with a phase sequence indicator in the
CAUTION presence of the York representative.

DO NOT cut wires to final length or make final

connections to motor terminals or starter power
Figure 4.5 Control Panel Positioning input terminals until approved by the York
NOTE representative.

GB 4-7
035-19569-101 (0109)

YK Motors (Electro-Mechanical Starter) 4.20 Thermal Insulation

(See Product Drawings Form 160.52-PA1)
Figure 4.6 shows the power wiring hook-up for Motor
Connections. (Refer to Wiring Labels in Motor Terminal DO NOT field insulate until the unit has been
Box for hook-up to suit motor voltage and amperage.) leak tested under the supervision of the York
representative.
Motor leads are furnished with a crimp type connection NOTE

having a clearance hole for a 3/8" bolt, motor terminal

lugs are not furnished. Insulation of the type specified for the job, or minimum
thickness to prevent sweating of 0°C (32°F) surfaces
4.19 Units with Solid State Starter or Variable should be furnished (by others) and applied to the
Speed Drive evaporator shell, end sheets, liquid feed line to
flow chamber, compressor suction connection, and
A unit equipped with a Solid State Starter or Variable evaporator liquid heads and connections. The liquid
Speed Drive does not require wiring to the compressor head flange insulation must be removable, to allow head
motor. The motor power wiring is factory connected to removal for the tube maintenance. Details of areas to be
the Solid State Starter or Variable Speed Drive (or an insulated are given on the Product Drawing.
optional factory installed disconnect switch). See Field
Wiring Diagram. All wiring to the control panel and the Units are furnished factory anti-sweat insulated on order
oil pump starter is completed by the factory. A control at additional cost. This includes all low temperature
transformer is supplied with the Solid State Starter or surfaces except the two (2) evaporator liquid heads.
Variable Speed Drive.
4.21 Installation Check

After the unit is installed, piped and wired the services

of a York representative should be requested to check
the installation and supervise the initial start-up and
operation on all chillers.

COMPRESSOR MOTOR FIELD CONNECTION DIAGRAM

MOTOR RATED LOAD AMPS

3 PHASE Current Transformer (CT) Ratio
MOTOR 200:1 350:1 700:1 1400:1
VOLTAGE Current (A)
200-600 65-111 (A) 112-224 (A) 225-829 (A) 830-1790 (A)
11-18 (C)
2300-4160 19-37 (B) 124-264 (A) 265-518 (A)
38-123 (A)
NOTES:
A. Requires passing motor lead through CT once before connecting to power supply.
B. Requires passing motor lead through CT twice before connecting to power supply.
C. Requires passing motor lead through CT three times before connecting to power supply.

Figure 4.6 Motor Connections (Electro-Mechanical Starter Application)

4-8 GB
 035-19569-101 (0109)

5 COMMISSIONING The customers disconnection devices can now be set

to ON.
5.1 Preparation
The machine is now live!
Commissioning of this unit should only be
carried out by York authorised personnel. WARNING

CAUTION

Oil Heater: Verify the oil heater is energised for at least

The Graphic Control Centre manual must be read in
12 hours prior to start-up.
conjunction with this section.
Water/Glycol system(s): Verify that the cooling and
Preparation - Power Off
chilled water systems have been installed correctly,
and has been commissioned with the correct direction
The following checks should be made with the customer
of water flow through the condenser and evaporator.
supply/supplies to the unit switched off.
Purge air from the top of the condenser and evaporator
Inspection: Inspect unit for installation damage. If found using the plugged air vents.
take action and/or repair as appropriate.
Flow switch(es): Verify a chilled water flow switch
Refrigerant charge: Units are normally shipped as is correctly fitted in the customer’s pipework on the
standard with a full refrigerant operating charge. Check evaporator outlet, and wired into the control panel.
that refrigerant is present and that no leaks are apparent.
Temperature sensor(s): Ensure the temperature
If no refrigerant is present a leak test must be undertaken,
sensors are coated with heat conductive compound
the leak(s) located and repaired. Repaired systems and
(Part No. 013-00890-000) and inserted into the sensor
units supplied with a nitrogen holding charge must be
pockets.
evacuated with a suitable vacuum pump/recovery unit
as appropriate (refer to Section 7 for details).
Programmed options: Verify that the options factory
programmed into the control centre are in accordance
Oil System: Check the oil system is correctly charged
with the customers order requirements. Refer to the
and the oil level is between the upper and lower sight
Graphic Control Centre Operating Instructions for
glasses on the oil reservoir.
details.
Isolation/protection: Verify that all sources of electrical
Programmed settings: Ensure the system setpoints,
supply to the unit are taken from a single point of
cut-outs and operational settings are in accordance
isolation.
with the instructions given in the Graphic Control Centre
Control panel: Check panel to see that it is free of Operating Instructions.
foreign materials (wire, metal chips, etc.) and clean out
Date & time: Programme the date and time (see Graphic
if required.
Control Centre Operating Instructions).
Power connections: Check the customer power cables
Start/Stop schedule: Programme the daily and holiday
are connected correctly.
start/stop (see Graphic Control Centre Operating
Earthing: Verify that the units protective terminal(s) are Instructions).
properly connected to a suitable earthing point. Ensure
that all unit internal earth connections are tight.

Supply voltage: Verify that the site voltage supply

corresponds to the unit requirement and is within the
limits given on the unit data plate.

GB 5-1
035-19569-101 (0109)

5.2 First Time Start-up

During the commissioning period there should be

sufficient heat load to run the unit under stable full
load operation to enable the unit controls, and system
operation to be set up correctly and a commissioning
log taken. Read the following section in conjunction with
the Graphic Control Centre Operating Instructions and
Section 6.

Interlocks: Verify that water is flowing through the

evaporator and that heat load is present. Ensure that any
remote run interlocks are in the run position and that the
run schedule requires the unit to run or is overridden.

Start-up: Start the unit in accordance with Section 6 and

be ready when the compressor starts to switch the unit
off immediately if any unusual noises or other adverse
conditions develop.

Operation: Check the system operating parameters are

normal by selecting the various readouts of pressure,
temperature, etc on the control centre.

5-2 GB
 035-19569-101 (0109)

6 OPERATION 6.2 Checking the Oil Level in the

Oil Reservoir
If the oil heater is de-energised during a
shutdown period, it must be energized for 12 Correct oil level - During operation, the oil level should
hours prior to starting the compressor. fall to the "Operating Range" identified on the vertical
CAUTION oil level indicator label. (See below).

LOW OIL OPERATING RANGE OVER FILL

6.1 Oil Heater Operation
If the oil level during operation is in the "Over Full" region
The oil heater operation is controlled by the graphic of the oil level indicator, oil should be removed from the
control centre (OptiView). The heater is turned on and oil reservoir, This reduces the oil level to the "Operating
off to maintain the oil temperature to a value 27.7 °C Range".
above the condenser saturation temperature. This is
the target value and if the oil temperature falls to 2.2 °C If the oil level during operation is in the "Low Oil" region
or more below the target, the heater is turned on. It is of the oil level indicator, oil should be added to the oil
turned off when the oil temperature increases to 1.6 °C reservoir (refer to Oil Charging Procedure, Section 7).
above the target value.
Comply with Local Regulations when removing
If the target value is greater than 71°C, the target defaults or disposing of oil.
to 71°C. If the target value is less than 43.3°C, it defaults
to 43.3°C. CAUTION

To prevent overheating of the oil in the event of a control 6.3 Start-up Procedure
centre component failure, the oil heater thermostat
(1HTR) is set to open at 82°C. 6.3.1 Pre-Starting
Prior to starting the chiller, observe the graphic control
centre (OptiView). Make sure the display reads SYSTEM
READY TO START.

To pre-start the chiller, use the following procedure:

1. Oil Heater – The oil heater must be energised for 12

hours prior to starting the chiller.

2. Prior to start, the clock must be programmed for the

proper day and time. Any setpoints to be changed
may be programmed. All control centre setpoints
should be programmed before the chiller is started
(refer to 160.54-OI for details).

GB 6-1
035-19569-101 (0109)

Figure 6.1 Control Centre

6.3.2 Start-up
1. If the chilled water pump is manually operated, start 1. The control centre display message will read
the pump. The control centre will not allow the chiller SYSTEM PRELUBE for the first 50 seconds of the
to start unless chilled liquid flow is established through starting sequence.
the unit. (A field supplied chilled water flow switch is
required.) If the chilled liquid pump is wired to the 2. The oil pump will start to circulate oil for a 50 second
graphic control centre the pump will automatically pre-run to establish oil flow and adequate lubrication
start. to all bearings, gears, and rotating surfaces within
the compressor. The high and low oil pressure
2. To start the chiller, press the compressor START (3) transducers (OP) and the oil temperature sensor
switch. This switch will automatically spring return (RT3) will sense any malfunction in the lubrication
to the RUN (I) position. When the start switch is system.
energised, the control centre is placed in an operating
mode and any fault will be shown by a display 3. The anti-recycle timer software function will operate
message. after the 50 seconds of pre-run time. At this time,
the timer will be initiated and will run for 30 minutes
Any faults which occur during STOP/RESET after the compressor starts. If the chiller shuts down
are also displayed. during this period of time, it cannot be started until
the timer completes the 30 minute cycle.
CAUTION

4. The chilled liquid pump contacts will close, starting

The pre-rotation vanes are closed automatically the chilled liquid pump, to establish liquid flow through
when the chiller is shut down to prevent loading the evaporator before the compressor starts.
the compressor on start-up.
CAUTION 5. After the first 50 seconds of operation, the compressor
will start.

When the chiller starts, the following automatic 6. For display messages and information pertaining
sequences are initiated: (Refer to Figures 6.2 and 6.3, to operation, refer to the Graphic Control Centre
Chiller Starting & Shutdown Sequence). (OptiView )Operating Instructions (160-54-OI).

6-2 GB
 035-19569-101 (0109)

** Not for all shutdowns. Refer to Graphic Control Centre Operating Instructions.

Figure 6.2 Chiller Starting Sequence and Shutdown Sequence

(Electro-mechanical and Solid State Starter Models)

** Not for all shutdowns. Refer to Graphic Control Centre Operating Instructions.

Figure 6.2 Chiller Starting Sequence and Shutdown Sequence

(Variable Speed Drive Models)

GB 6-3
035-19569-101 (0109)

6.4 Chiller Operation 6.5 Operating Log Sheet

After the compressor reaches operating speed, the pre- An accurate record of system operating conditions
rotation vanes will begin to open under the control of the (temperatures and pressures) recorded at regular
microprocessor which senses the leaving chilled liquid intervals throughout each 24 hour operating period
temperature. The unit capacity will vary to maintain the should be kept. An optional status printer is available
leaving CHILLED LIQUID TEMPERATURE SETPOINT. for this purpose using automatic data logging after
The pre-rotation vanes are modulated by an actuator programming the DATA LOGGER function.
under the control of the microprocessor. The vane control
routine employs proportional plus derivative (rate) control The record of readings serves as a valuable reference
action. A drop in chilled liquid temperature will cause for operating the system. Readings taken when a system
the actuator to close the pre-rotation vanes to decrease is newly installed will establish normal conditions with
chiller capacity. When the chilled liquid temperature which to compare later readings.
rises, the actuator will open the pre-rotation vanes to
increase the capacity of the chiller. For example, an increase in condenser water temperature
difference (leaving condenser water temperature minus
However, the current draw (A) of the compressor motor entering condenser water temperature) may be an
cannot exceed the setting of the % CURRENT LIMIT at indication of dirty condenser tubes.
any time during the unit operation. The microprocessor
40% to 100% three-phase peak current limit software 6.6 Maintenance and Service
function, plus the 3-phase 100% solid state overload
If the system is malfunctioning or the unit is stopped by
current limiter (CM-2), on Electro-Mechanical Starter
one of the safety controls, consult Section 8. After repair
applications, or the Solid State Starter current limit
or adjustment the compressor cannot be started or the
function will override the temperature control function
particular fault continues to affect the performance of the
and prevent the pre-rotation vanes from opening beyond
unit, please call the nearest York Office. Failure to report
the % CURRENT LIMIT setting.
constant troubles could damage the unit and increase
the cost of repairs.
If the load continues to decrease, after the pre-rotation
vanes are entirely closed, the chiller will be shut down by
6.6.1 Normal and Safety System Shutdowns
the Leaving Chilled Liquid – Low Temperature Control.
Normal and safety system shutdowns have been built into
6.4.1 Condenser Water Temperature Control the unit to protect it from damage during certain operating
conditions. The system will be stopped automatically
The unit is designed to use less power by taking
by controls that respond to high temperatures, low
advantage of lower than design temperatures that are
temperatures, and low and high pressures, etc.
naturally produced by cooling towers throughout the
operating year. Exact control of condenser water such
as a cooling tower bypass, is not necessary for most
installations. The chiller requires only that the minimum
condenser water temperature be no lower than the value
determined by referring to the formula below:

Where:

ECWT = Entering Condenser Water Temperature

LCWT = Leaving Chilled Water Temperature

C RANGE = Condensing Water Temperature Range at

the given load condition

At start-up, the entering condenser water temperature

may be as much as 14 °C colder than the return
chilled water temperature. Cooling tower fan cycling
will normally provide adequate control of the entering
condenser water temperature on most installations.

6-4 GB
 035-19569-101 (0109)

6.6.2 Safety Shutdowns Solid State Starter Shutdowns

If the chiller shuts down on a SAFETY shutdown,
• LCSSS Shutdown - Requesting Fault Data
the chiller will restart when the shutdown condition is
removed. These shutdowns require the operator to • LCSSS - High Instantaneous Current
manually reset the graphic control centre (OptiView) • LCSSS - High Phase (X) Heatsink Temperature
prior to restarting the chiller. -Running
Common Shutdowns • LCSSS - 105% Motor Current Overload
• LCSSS - Phase (X) Shorted SCR
• Evaporator – Low Pressure
• LCSSS - Open SCR
• Evaporator - Low pressure - Smart freeze
• LCSSS - Phase Rotation
• Evaporator – Transducer or Leaving Liquid Probe
• Evaporator – Transducer or Temperature Sensor Variable Speed Drive Shutdowns
• Condenser – High Pressure Contacts Open • VSD Shutdown – Requesting Fault Data
• Condenser – High Pressure • VSD – 105% Motor Current Overload
• Condenser – Pressure Transducer Out 0f Range • VSD – High Phase A Inverter Heatsink Temp.
• Auxiliary Safety – Contacts Closed • VSD – High Phase B Inverter Heatsink Temp.
• Discharge – High Temperature • VSD – High Phase C Inverter Heatsink Temp.
• Discharge – Low Temperature • VSD – High Converter Heatsink Temperature
• Oil – High Temperature • VSD - High Inverter Baseplate Temperature
• Oil – Low Differential Pressure • VSD - High Phase A Inverter Baseplate
• Oil – High Differential Pressure Temperature
• Oil – Pump Pressure Transducer Out of Range • VSD - High Phase B Inverter Baseplate
Temperature
• Oil – Sump Pressure Transducer Out of Range
• VSD - High Phase C Inverter Baseplate
• Oil – Differential Pressure Calibration
Temperature
• Oil – Variable Speed Pump – Pressure Setpoint
• VSD – Precharge Lockout
Not Achieved
• Harmonic Filter – High Heatsink Temperature
• Control Panel – Power Failure
• Harmonic Filter – High Total Demand Distortion
• Motor or Starter – Current Imbalance
* Compressors H3 and J only
• Thrust Bearing – Proximity Probe Clearance
• Thrust Bearing – Proximity Probe Out of Range **Compressors P, Q, H4 thru H8 only
• Thrust Bearing - Limit Switch Open**
• Watchdog – Software Reboot
• Surge protection - Excess surge

GB 6-5
035-19569-101 (0109)

6.6.3 Cycling Shutdowns • VSD - High Converter Heatsink Temperature

If the chiller shuts down on a CYCLING shutdown, • VSD – Phase A Gate Driver
the chiller will automatically restart when the cycling • VSD – Phase B Gate Driver
condition is removed. These shutdowns do not require • VSD – Phase C Gate Driver
the operator to manually reset the control centre prior
• VSD – Single Phase Input Power
to restarting the chiller.
• VSD – High DC Bus Voltage
Common Shutdowns • VSD – Logic Board Power Supply
• VSD – Low DC Bus Voltage
• Multi-unit Cycling – Contacts Open
• VSD – DC Bus Voltage Imbalance
• System Cycling – Contacts Open
• VSD – Pre-Charge DC Bus Voltage Imbalance
• Oil – Low Temperature Differential
• VSD – High Internal Ambient Temperature
• Oil – Low Temperature
• VSD – Invalid Current Scale Selection
• Control Panel – Power Failure
• VSD – Low Phase A Inverter Heatsink Temp.
• Leaving Chilled Liquid – Low Temperature
• VSD – Low Phase B Inverter Heatsink Temp.
• Leaving Chilled Liquid – Flow Switch Open
• VSD – Low Phase C Inverter Heatsink Temp.
• Condenser - Flow Switch Open
• VSD – Low Converter Heatsink Temperature
• Motor Controller – Contacts Open
• VSD - Low Phase A Inverter Baseplate
• Motor Controller – Loss of Current Temperature
• Power Fault • VSD - Low Phase B Inverter Baseplate
• Control Panel – Schedule Temperature
• Proximity Probe – Low Supply Voltage • VSD - Low Phase C Inverter Baseplate
• Oil – Variable Speed Pump – Drive Contacts Temperature
Open • VSD – Pre-Charge – Low DC Bus Voltage
• VSD - Low Inverter Baseplate Temperature
Solid State Starter Shutdowns
• VSD – Logic Board Processor
• LCSSS Initialization Failed • VSD – Run Signal
• LCSSS - Serial Communications • VSD – Serial Communications
• LCSSS - Requesting Fault Data • Harmonic Filter – Logic Board or Communications
• LCSSS - Stop Contacts Open • Harmonic Filter – High DC Bus Voltage
• LCSSS - Power Fault • Harmonic Filter – High Phase A Current
• LCSSS - Low Phase (X) Temperature Sensor • Harmonic Filter – High Phase B Current
• LCSSS - Run Signal • Harmonic Filter – High Phase C Current
• LCSSS - Invalid Current Scale Selection • Harmonic Filter – Phase Locked Loop
• LCSSS - Phase Locked Loop • Harmonic Filter – Precharge-Low DC Bus Voltage
• LCSSS - Low Supply Line Voltage • Harmonic Filter – Low DC Bus Voltage
• LCSSS - High Supply Line Voltage • Harmonic Filter – DC Bus Voltage Imbalance
• LCSSS - Power Fault • Harmonic Filter – Input Current Overload
• LCSSS - Logic Board Processor • Harmonic Filter – Logic Board Power Supply
• LCSSS - Logic Board Power Supply • Harmonic Filter – Run Signal
• LCSSS - Phase Rotation / Loss • Harmonic Filter – DC Current Transformer 1
• LCSSS - Phase Loss • Harmonic Filter – DC Current Transformer 2
Variable Speed Drive Shutdowns •

• VSD Shutdown – Requesting Fault Data

• VSD – Stop Contacts Open
• VSD Initialization Failed
• VSD – High Phase A Instantaneous Current
• VSD – High Phase B Instantaneous Current
• VSD – High Phase C Instantaneous Current

6-6 GB
 035-19569-101 (0109)

6.7 Stopping the System 6.8 Prolonged Shutdown

The graphic control centre (OptiView) can be programmed If the chiller is to be shut down for an extended period of
to start and stop automatically (maximum, once each time (for example, over the winter season), the following
day) whenever desired. To stop the chiller, proceed as paragraphs detail the procedure to be followed.
follows:
1. Test all system joints for refrigerant leaks with a
1. Push the compressor STOP/RESET(O) switch. The leak detector. If any leaks are found, they should be
compressor will stop automatically. The oil pump will repaired before allowing the system to stand for a
continue to run for shutdown period. The oil pump long period of time.
will then stop automatically.
During long idle periods, the tightness of the system
2. Stop the chilled water pump (if not wired into the should be checked periodically.
graphic control centre, in which case it will shut off
automatically simultaneously with the oil pump.) (The 2. If freezing temperatures are encountered while the
actual water pump contact operation is dependent system is idle, carefully drain the water from the
upon the position of the microprocessor board jumper cooling tower, condenser, condenser pump, and the
J54.) chilled water system, chilled water pump and coils.

3. Open the switch to the cooling tower fan motors, if Open the drains on the evaporator and condenser
used. liquid heads to assure complete drainage. (If a
Variable Speed Drive is fitted, drain its water cooling
4. The compressor sump oil heater (thermostatically system. If a Solid State Starter is fitted drain water
controlled) is energised when the unit is stopped. from starter cooling loop).

3. On the SETUP Screen, disable the clock. This

conserves the battery.

4. Open the main disconnect switches to the compressor

motor, condenser water pump and the chilled water
pump. Open the 115 V circuit to the control centre.

6.9 Start-up after Prolonged Shutdown

1. When putting the system into operation after

prolonged shutdown (during the winter), remove all oil
from the compressor. Install a new filter element and
charge the compressor with fresh oil. On the SETUP
Screen, enable the clock. Energise the 115 V circuit to
the control centre to energise the compressor sump
oil heater for at least 12 hours.

2. Operate the Oil Pump (press and release the

MANUAL OIL PUMP key) until steady oil pressure is
established. Then press and release the OIL PUMP
key to stop operation of the oil pump. If the water
systems were drained, fill the condenser water circuit
and chilled liquid circuit.

GB 6-7
035-19569-101 (0109)

Page Left Intentionally Blank

6-8 GB
 035-19569-101 (0109)

7 MAINTENANCE 4. Check the entering and leaving chilled liquid

temperatures and evaporator pressure are correct
The units have been designed to operate continuously for design conditions on the SYSTEM Screen.
provided they are regularly maintained and operated
5. Check the condenser saturation temperature (based
within the limitations given in this manual. Each unit
upon condenser pressure sensed by the condenser
should be included in a routine schedule of daily
transducer) on the SYSTEM Screen.
maintenance checks by the operator/customer, backed
up by regular service inspection and maintenance visits
6. Check the compressor discharge temperature on the
by a suitably qualified Service Engineer.
SYSTEM Screen. During normal operation discharge
temperature should not exceed 104 °C .
It is entirely the responsibility of the owner to provide for
these regular maintenance requirements and/or enter
7. Check the compressor motor current on the SYSTEM
into a maintenance agreement with York International
Screen.
service organisation to protect the operation of the unit.
If damage or a system failure occurs due to improper
8. Check for any signs of dirty or fouled condenser tubes.
maintenance during the warranty period, York shall
(The temperature difference between condenser
not be liable for costs incurred to return the unit to
leaving liquid and saturated condensing temperature
satisfactory condition.
should not exceed the difference recorded for a new
unit by more than 2.2°C).
This maintenance section applies to the basic
unit only and may, on individual contracts, be
7.1.3 Weekly
supplemented by additional requirements to
NOTE cover any modifications or ancillary equipment 1. Check the refrigerant charge (See Refrigerant
as applicable. Charge Checking).

The Safety Section of this manual should 7.1.4 Every 3 Months

be read carefully before attempting any
1. Perform chemical analysis of oil.
maintenance operations on the unit. This
WARNING section should be read in conjunction with the
2. The unit should be leak tested. Any leaks found must
MBCS Manual.
be repaired immediately.
7.1 Inspections 7.1.5 Every 6 Months
(or more often as required)
7.1.1 Scheduled Maintenance
1. Change and inspect compressor oil filter element.
The maintenance operations detailed in the following
paragraphs should be carried out on a regular basis
2. Oil return system:
by a suitably qualified Service Engineer. It should be
noted that the interval necessary between each ‘minor’ a. Change dehydrator or earlier if the oil return system
and ‘major’ service can vary depending on, for instance, fails to operate.
application, site conditions and expected operating
schedule. Normally a ‘minor’ service should be carried b. Check nozzle of eductor for foreign particles.
out every three to six months and a ‘major’ service once
a year. It is recommended that your local York Service 3. Check controls and safety cutouts.
Centre is contacted for recommendations for individual
sites.

7.1.2 Daily
1. Check graphic control centre (OptiView) displays.

2. If the compressor is in operation, check the bearing

oil pressure on the SYSTEM Screen. Also check the
oil level in the oil reservoir. Operating oil level should
be between the upper and lower sight glasses. Drain
or add oil if necessary.

3. Check entering and leaving condenser water

pressure and temperatures are correct for design
conditions on the SYSTEM Screen.

GB 7-1
035-19569-101 (0109)

COMPRESSOR

SOLENOID VALVE

CONDENSER

EVAPORATOR

CHECK VALVE OIL EDUCTOR BLOCK

SOLENOID VALVE

STOP VALVE DEHYDRATOR

STOP VALVE

Figure 7.1 Oil Return System

7.1.6 Annually (more often if necessary) 7.2 Oil Return System

1. Drain and replace the oil in the compressor oil sump
The oil return system continuously maintains the proper
(See Oil Charging Procedure).
oil level in the compressor oil sump (Refer to Figures
2.6 and 7.1).
2. Evaporator and Condenser:
High pressure condenser gas flows continuously through
a. Inspect and clean water strainers.
the eductor inducing the low pressure, oil rich liquid to
b. Inspect and clean tubes as required. flow from the evaporator, through the dehydrator to the
compressor sump.
c. Inspect end sheets.
7.2.1 Changing the Dehydrator
3. Compressor Motor (See motor manufacturers To change the dehydrator, use the following
maintenance and service instruction supplied with procedure:
unit):
1. Shut the stop valves on the condenser gas line,
a. Clean air passages and windings per manufacturers oil return line to rotor support and inlet end of the
instructions. dehydrator.

b. Test winding insulation. 2. Remove the dehydrator, refer to figure 7.1.

c. Lubricate ball bearings. 3. The nozzle of the eductor should be checked for any
foreign particles that may be obstructing the jet.
4. Inspect and service electrical components as
necessary. 4. Assemble the new filter-drier.

5. Perform chemical analysis of system. 5. Open condenser stop valve and check dehydrator
connections for refrigerant leaks.

6. Open all the dehydrator stop valves to allow the

liquid refrigerant to flow through the dehydrator and
condenser gas through the eductor.

7-2 GB
 035-19569-101 (0109)

Figure 7.2 Oil Reservoir Charging

7.3 Oil Charge

The nominal oil charge for the compressor is 75.7 litres, 4. As soon as oil charging is complete, restore the power
of York “K” oil. Only York “K” refrigeration oil must be supply to energise the oil heater. This will keep the
used in the centrifugal compressor. Since oil absorbs concentration of refrigerant in the oil to a minimum.
moisture when exposed to the atmosphere, it should be
kept tightly capped until used. When the oil reservoir is initially charged with
oil, the oil pump should be started manually to
7.3.1 Oil Charging Procedure fill the lines, passages, oil cooler and oil filter.
CAUTION This will lower the oil level in the reservoir. It will
The compressor oil level must be maintained between
then be necessary to add oil to bring the level
the oil reservoir’s upper and lower sight glasses. If the
back to the centre of the upper sight glass.
oil level falls into the lower sight glass, it is necessary to
add oil to the compressor oil reservoir. The oil should be
charged into the oil reservoir using the an oil charging 7.4 Refrigerant Charge
pump(Part No. 070-10654). To charge oil into the oil
The refrigerant system is pressure tested and evacuated
reservoir, proceed as follows:
at the factory.
1. The unit must be shut down.
7.4.1 Checking The Refrigerant Charge
2. Immerse the suction connection of the oil charging The refrigerant level should have been observed
pump in a clean container of new oil and connect the and the level recorded after initial charging. With
pump discharge connection to the oil charging valve the correct charge the level should visible in the
(A) located on the oil reservoir cover plate. (figure sight glass.
7.2). Do not tighten the connection at the charging
valve until after the air is forced out by pumping a few The refrigerant charge should always be
strokes of the oil pump. This fills the lines with oil and checked and trimmed when the system is shut
prevents air from being pumped into the system. down.
NOTE

3. Open the oil charging valve and pump oil into the
system until oil level in the compressor oil reservoir The refrigerant charge level must be checked after the
is about midway in the upper sight glass. Then, pressure and temperature have equalised between the
close the charging valve and disconnect the hand condenser and evaporator. This would be expected
oil pump. to be 4 hours or more after the compressor and water
pumps are stopped.

GB 7-3
035-19569-101 (0109)

Figure 7.3 Unit Evacuation

7.4.2 Leak Testing causing leaks, the temperature should be brought

After the system has been charged, the system should up slowly so that the tubes and shell are heated
be carefully leak tested with a R134a compatible leak evenly.
detector to ensure all joints are tight.
5. Close the system charging valve and the stop valve
Otherwise, it is recommended to perform a leak test between the vacuum indicator and the vacuum
quarterly. pump. Then disconnect the vacuum pump leaving
the vacuum indicator in place.
If any leaks are indicated, they must be repaired
immediately. Usually, leaks can be stopped by tightening 6. Hold the vacuum in the system for 8 hours; the
flare nuts or flange bolts. However, for any major repair, slightest rise in pressure indicates a leak or the
the refrigerant charge must be removed. presence of moisture, or both. If, after 8 hours the
wet bulb temperature in the vacuum indicator has
7.4.3 Vacuum Testing not risen above 4.4°C or a pressure of 6.3 mm Hg,
the system may be considered tight.
Vacuum testing should be conducted as follows:
Be sure the vacuum indicator is valved off while holding
1. Connect a high capacity vacuum pump, with indicator, the system vacuum and be sure to open the valve
to the system charging valve as shown in figure 7.3 between the vacuum indicator and the system when
and start the pump. checking the vacuum after the 8 hour period.
2. Open wide all system valves. Be sure all valves to 7. If the vacuum does not hold for 8 hours within
the atmosphere are closed. the limits specified, the leak must be found and
repaired.
3. Operate the vacuum pump until a wet bulb
temperature of 0°C or a pressure of 5 mm Hg
(absolute) is reached.

4. To improve evacuation circulate warm water (not to

exceed 50°C) through the evaporator and condenser
tubes to thoroughly dehydrate the shells. If a source
of hot water is not readily available, a portable
water heater should be employed. DO NOT USE
STEAM.

A suggested method is to connect a hose between

the source of hot water under pressure and the
evaporator head drain connection, out the evaporator
vent connection, into the condenser head drain and
out the condenser vent. To avoid the possibility of

7-4 GB
 035-19569-101 (0109)

7.4.4 Refrigerant Charging 1. The condenser tubes should be cleaned annually

or earlier if conditions warrant. If the temperature
When opening any part of the refrigerant
difference between the water off the condenser and
system for repairs, the refrigerant charge
the condenser liquid temperature is more than 2.2 K
must be removed. If the chiller is equipped
greater than the difference recorded on a new unit, it
NOTE with optional valves, the refrigerant can be
is a good indication that the condenser tubes require
isolated in either the condenser or evaporator
cleaning.
/ compressor while making repairs.
2. The evaporator tubes under normal circumstances
To prevent liquid freezing within the evaporator tubes
will not require cleaning. If however the temperature
when charging an evacuated system, only refrigerant
difference between the refrigerant and the chilled
vapour must be added to the system until the system
water increases slowly over the operating season,
pressure is raised above the point corresponding to the
it is an indication that the evaporator tubes may be
freezing point of the evaporator liquid. For water, the
fouling or that there may be a water by-pass in the
pressure corresponding to the freezing point is 58.9 kPa
water box requiring gasket replacement or refrigerant
for R134a (at sea level).
may have leaked from the chiller.
While charging, care must be taken to prevent
7.5.1 Chemical Water Treatment
moisture laden air from entering the system.
Since the mineral content of the water circulated through
NOTE the evaporator and condenser varies with almost every
source of supply, it is possible that the water being used
Make up a suitable charging connection from new
may corrode the tubes or deposit heat resistant scale in
copper tubing to fit between the system charging valve
them. Reliable water treatment will greatly reduce the
and the fitting on the charging drum. This connection
corrosive and scale forming properties of almost any
should be as short as possible but long enough to permit
type of water.
sufficient flexibility for changing drums. The charging
connection should be purged each time a new container As a preventive measure against scale and corrosion
of refrigerant is connected and changing containers and to prolong the life of evaporator and condenser
should be done as quickly as possible to minimise the tubes, a chemical analysis of the water should be
loss of refrigerant. made preferably before the system is installed. A water
treatment expert should be consulted to determine
Refer to Section 9.2 for details of refrigerant charge
whether water treatment is necessary, and if so, to
weights.
furnish the proper treatment for the particular water
condition.
7.5 Condenser and Evaporator
7.5.2 Tube Cleaning
The major portion of maintenance on the condenser
and evaporator is maintaining the water side of the Evaporator
condenser and evaporator in a clean condition.
It is difficult to determine by any particular test whether
The use of untreated water in cooling towers, closed possible lack of performance of the water evaporator
water systems, etc. frequently results in one or more of is due to fouled tubes alone or due to a combination
the following: of troubles. Trouble which may be due to fouled tubes
is indicated when, over a period of time, the cooling
1. Scale Formation. capacity decreases and the split (temperature difference
between water leaving the evaporator and the refrigerant
2. Corrosion or Rusting. temperature in the evaporator) increases. A gradual
drop-off in cooling capacity can also be caused by a
3. Slime and Algae Formation. gradual leak of refrigerant from the system or by a
combination of fouled tubes and shortage of refrigerant
It is therefore to the benefit of the user to provide for charge. An excessive quantity of oil in the evaporator
proper water treatment to provide for a longer and can also contribute to erratic performance.
more economical life of the equipment. The following
recommendation should be followed in determining
the condition of the water side of the condenser and
evaporator tubes.

GB 7-5
035-19569-101 (0109)

Condenser Acid Cleaning of Tubes

Condenser trouble due to fouled tubes is usually If the tubes are fouled with a hard scale deposit, they
indicated by a steady rise in head pressure, over a period may require acid cleaning. It is important that before acid
of time, accompanied by a steady rise in condensing cleaning, the tubes be cleaned by the brushing process
temperature, and noisy operation. These symptoms may described above. If the relatively loose foreign material is
also be due to foul gas build-up. Purging will remove the removed before the acid cleaning, the acid solution will
foul gas revealing the effect of fouling. have less material to dissolve and flush from the tubes
with the result that a more satisfactory cleaning job will
Tube Fouling be accomplished with a probable saving of time.

Fouling of the tubes can be due to deposits of two types Acid cleaning should only be performed by an expert.
as follows: Please consult your local water treatment representative
for assistance in removing scale build-up and preventative
1. Rust or sludge - which finds its way into the tubes maintenance programs to eliminate future problems.
and accumulates there. This material usually does
not build up on the inner tube surfaces as scale, 7.5.4 Tube Leaks
but does interfere with the heat transfer. Rust or
Evaporator and condenser tube leaks may result in
sludge can generally be removed from the tubes by
refrigerant leaking into the water circuit, or water leaking
a thorough brushing process.
into the shell depending on the pressure levels. If
2. Scale - due to mineral deposits. These deposits, refrigerant is leaking into the water, it can be detected
even though very thin and scarcely detectable upon at the liquid head vents after a period of shutdown. If
physical inspection, are highly resistant to heat water is leaking into the refrigerant, system capacity and
transfer. They can be removed most effectively by efficiency will drop off sharply.
circulating an acid solution through the tubes.
If a tube is leaking and water has entered the system,
the evaporator and condenser should be valved off from
7.5.3 Tube Cleaning Procedures
the rest of the water circuit and drained immediately to
Brush Cleaning of Tubes prevent severe rusting and corrosion. The refrigerant
system should then be drained and purged with dry
If the tube consists of dirt and sludge, it can usually be nitrogen to prevent severe rusting and corrosion. If a
removed by means of the brushing process. Drain the tube leak is indicated, the exact location of the leak may
water sides of the circuit to be cleaned (cooling water or be determined as follows:
chilled water) remove the heads and thoroughly clean
each tube with a soft bristle bronze or nylon brush. DO 1. Remove the heads and listen at each section of tubes
NOT USE A STEEL BRISTLE BRUSH. A steel brush for a hissing sound that would indicate gas leakage.
may damage the tubes. This will assist in locating the section of tubes to be
further investigated. If the probable location of the
Improved results can be obtained by admitting water into leaky tubes has been determined, treat that section
the tube during the cleaning process. This can be done in the following manner (if the location is not definite,
by mounting the brush on a suitable length of 1/8" pipe all the tubes will require investigation).
with a few small holes at the brush end and connecting
the other end by means of a hose to the water supply. 2. Wash off both tube heads and the ends of all tubes
with water.
The tubes should always be brush cleaned
before acid cleaning. 3. With nitrogen or dry air, blow out the tubes to clear
them of traces of refrigerant laden moisture from the
NOTE
circulation water. As soon as the tubes are clear,
a cork should be driven into each end of the tube.
Pressurise the dry system with 350 to 690 kPag of
nitrogen. Repeat this with all of the other tubes in the
suspected section or, if necessary, with all the tubes
in the evaporator or condenser. Allow the evaporator
or condenser to remain corked up to 12 to 24 hours
before proceeding. Depending upon the amount of
leakage, the corks may blow from the end of a tube,
indicating the location of the leakage. If not, it will be
necessary to make a very thorough test with the leak
detector.

7-6 GB
 035-19569-101 (0109)

4. After the tubes have been corked for 12 to 24 hours, 2. Oil Changing - The oil in the compressor must be
it is recommended that two men working at both changed annually or earlier if it becomes dark or
ends of the evaporator carefully test each tube – one cloudy. However, quarterly oil analysis can eliminate
man removing corks at one end and the other at the the need for an annual change provided the analysis
opposite end to remove corks and handle the leak indicates there is no problem with the oil.
detector. Start with the top row of tubes in the section
being investigated. Remove the corks at the ends 7.7 Compressor Motor
of one tube simultaneously and insert the exploring
tube for 5 seconds – this should be long enough to 1. Check motor mounting screws frequently for
draw into the detector any refrigerant gas that might tightness.
have leaked through the tube walls. A fan placed at
the end of the evaporator opposite the detector will 2. Check motor winding insulation annually for
assure that any leakage will travel through the tube deterioration of windings.
to the detector.
3. For the lubrication instructions, refer to the motor
5. Mark any leaking tubes for later identification. manual

6. If any of the tube sheet joints are leaking, the leak

should be indicated by the detector. If a tube sheet
leak is suspected, its exact location may be found
by using a soap solution. A continuous buildup of
bubbles around a tube indicates a tube sheet leak.

7.6 Compressor

Maintenance for the compressor assembly consists

of checking the operation of the oil return system and
changing the dehydrator, checking and changing the
oil, checking and changing the oil filters, checking
the operation of the oil heater, checking the operation
of the oil pump, and observing the operation of the
compressor.

Internal wearing of compressor parts could be a serious

problem caused by improper lubrication, brought about
by restricted oil lines, passages, or dirty oil filters. If the
unit is shutting down on (HOT) High Oil Temperature
or Low Oil Pressure (OP), change the oil filter element.
Examine the oil filter element for the presence of
aluminum particles. Aluminum gas seal rings can contact
the impeller and account for some aluminum particles
to accumulate in the oil filter, especially during the initial
start up and first several months of operation. However,
if aluminum particles continue to accumulate and the
same conditions continue to stop the unit operation after
a new filter is installed, contact your local York Service
Agent.

1. Oil Filter - The oil filter must be changed when the

variable speed oil pump (VSOP) Drive frequency
increases to 55 Hz to maintain the target oil
pressure

When the oil filter is changed, it should be inspected

thoroughly for any aluminum particles which would
indicate possible bearing wear. If aluminum particles
are found this should be brought to the attention of
the nearest York office for their further investigation
and recommendations.

GB 7-7
035-19569-101 (0109)

7.8 Electrical Controls 7.9 Testing Motor Winding Insulation

1. All electrical controls should be inspected for With the main disconnect switch and compressor motor
obvious malfunctions. starter open, test the motor as follows:

2. It is important that the factory settings of controls 1. Test the insulation, using a megohm meter (megger),
(operation and safety) are not changed. If the settings between phases and each phase and ground (see
are changed without York approval, the warranty will be figure 7.4); these readings are to be interpreted using
invalidated. the graph shown in figure 7.5.

For information covering the graphic control centre 2. If readings fall below shaded area, remove external
(OptiView) operation, refer to manual 160.54-O1. leads from motor and repeat test.

Motor is to be megged with the starter at

ambient temperature after 24 hours of idle
standby.
CAUTION

Figure 7.4 Insulation Testing of Motor Windings

Figure 7.5 Motor Stator Insulation Resistance

7-8 GB
 035-19569-101 (0109)

8 TROUBLSHOOTING

Fault Possible Cause Remedy

1. SYMPTOM: Abnormally High Discharge Pressure
Temperature difference between Air in condenser. Bleed cooling water circuit.
condensing temperature
and condenser leaving liquid
temperature higher than normal.
High discharge pressure. Condenser tubes dirty or scaled. Clean condenser tubes. Check
water treatment.
High condenser water temperature. Reduce condenser water inlet
temperature. (Check cooling tower
and water circulation.)
Temperature difference between Insufficient condensing water flow. Increase the water flow through the
condenser entering liquid condenser to correct value.
and condenser leaving liquid
higher than normal, with normal
evaporator pressure.
2. SYMPTOM: Abnormally Low Suction Pressure
Temperature difference between Insufficient charge of refrigerant. Check for leaks and charge
leaving chilled water and refrigerant into system.
refrigerant in evaporator greater Variable orifice problem. Remove obstruction.
than normal with high discharge
temperature.
Temperature difference between Evaporator tubes dirty or restricted. Clean evaporator tubes.
leaving chilled water and
refrigerant in the evaporator
greater than normal with normal
discharge temperature
Temperature of chilled water too Insufficient load for system Check pre-rotation vane motor
low with low motor current. capacity. operation and setting of low water
temperature cut-out.
3. SYMPTOM: High Evaporator Pressure
High chilled water temperature. Pre-rotation vanes fail to open. Check the pre-rotation vane motor
positioning circuit.
System overload. Be sure the vanes are wide open
(without overloading the motor)
until the load decreases.
4. SYMPTOM: No Oil Pressure when System Start Button Pushed
Low oil pressure displayed on Oil pump running in wrong Check rotation of oil pump
control centre; compressor will not direction. (Electrical Connections).
start.
Oil pump not running. Troubleshoot electrical problem
with oil pump VSD.

GB 8-1
035-19569-101 (0109)

Fault Possible Cause Remedy

5. SYMPTOM: Unusually High Oil Pressure develops when Oil Pump Runs
Unusually high oil pressure is High oil pressure. Transducer Replace low or high oil pressure
displayed when the oil pressure defective. transducer.
display key is pressed when the oil
pump is running.
6. SYMPTOM: Oil Pump Vibrates or is Noisy
Oil pump vibrates or is extremely Oil not reaching pump suction inlet Check oil supply and oil piping.
noisy with some oil pressure when in sufficient quantity.
pressing OIL PRESSURE display Worn or failed oil pump. Repair/Replace oil pump.
key.
Note: When oil pump is run
without an oil supply it will
vibrate and become extremely
noisy.
7. SYMPTOM: Reduced Oil Pump Capacity
Oil pump pumping capacity. Excessive end clearance on pump. Inspect and replace worn parts.
Other worn pump parts.
Partially blocked oil supply inlet. Check oil inlet for blockage.
8. SYMPTOM: Oil Pressure Gradually Decreases (Noted by Observation of Daily Log Sheets)
When oil pump VSD frequency Oil filter is dirty. Change oil filter.
increases to 55 + hz to maintain
target oil pressure.
9. SYMPTOM: Oil Pressure System Ceases to return an Oil/Refrigerant Sample
Oil refrigerant return not Filter-drier in oil return system dirty. Replace old filter-drier with new.
functioning. Jet or orifice of oil return jet Remove jet, inspect for dirt.
clogged. Remove dirt using solvent and
replace.
10. SYMPTOM: Oil Pump Fails to deliver Oil Pressure
No oil pressure registers when Faulty oil pressure transducer. Replace oil pressure transducer.
pressing OIL PRESSURE display Faulty wiring/connectors.
key when oil pump runs

8-2 GB
 035-19569-101 (0109)

9 TECHNICAL DATA

9.1 Dimensions

P and Q Compressors
COMPRESSOR
OPTIVIEW
MOTOR
CONTROL CENTER

J2 H2

B4,5
EVAP

CONDENSER

E C D
G2 F2 A
(EVAP) (EVAP) (SHIPPING WIDTH) M

ADDITIONALOPERATING HEIGHT CLEARANCE TO FLOOR Q3 COMPRESSOR

TYPE OF CHILLER MOUNTING M EVAPORATOR-CONDENSER SHELL CODES
NEOPRENE PAD ISOLATORS 45 A-A C-C D-D
SPRING ISOLATORS 1" DEFLECTION 25 A 1549 1676 1676
DIRECT MOUNT 19 B 2134 2229 2229
C 394 445 445
D 381 394 394
E 3658 3658 4877

P7, Q7 COMPRESSOR Q4 COMPRESSOR

EVAPORATOR-CONDENSER SHELL CODES EVAPORATOR-CONDENSER SHELL CODE
E-E F-F C-C D-D E-E
A 1880 1880 A 1676 1676 2134
B 2454 2454 B 2197 2197 2350
C 495 495 C 445 445 495
D 445 445 D 394 394 445
E 3658 4877 E 3658 4877 3658

P8 COMPRESSOR Q5 COMPRESSOR
EVAPORATOR-CONDENSER SHELL CODES EVAPORATOR-CONDENSER SHELL CODES
G-E H-F J-J L-L C-C D-D E-E F-F
A 2108 2108 2299 2299 A 1676 1676 2134 2134
B 3200 3200 3327 3327 B 2403 2403 2578 2578
C 610 610 641 641 C 445 445 495 495
D 445 445 508 508 D 394 394 445 445
E 3658 4877 3658 4877 E 3658 4877 3658 4877

P9 COMPRESSOR Q6 COMPRESSOR
EVAPORATOR-CONDENSER SHELL CODES EVAPORATOR-CONDENSER SHELL CODES
H-F J-J L-L E-E F-F
A 2108 2299 2299 A 2134 2134
B 3124 3264 3264 B 2515 2515
C 610 641 641 C 495 495
D 445 508 508 D 445 445
E 4877 3658 4877 E 3658 4877

GB 9-1
035-19569-101 (0109)

H Compressors

178

ADDITIONALOPERATING HEIGHT CLEARANCE

TYPE OF CHILLER MOUNTING M
NEOPRENE PAD ISOLATORS 44
SPRING ISOLATORS 25MMDEFLECTION 25
DIRECT MOUNT 19

H9 COMPRESSORS
EVAP.-COND.SHELL CODES
K-K M-M
A 2299 2616
B 3150 3315
C 641 724
D 508 584
E 4267 4267

NOTES:
1. All dimensions are approximate. Certified dimensions are available on request.
2. For all water boxes (compact shown above), determine overall unit length by adding water box depth to tube sheet length.
3. Water nozzles can be located on either end of unit. Add 13 mm to nozzle length for flanged connections.
4. To determine overall height, add dimension "M" for the appropriate isolator type.
5. Use of motors with motor hoods may increase overall unit dimensions.

9-2 GB
 035-19569-101 (0109)

K Compressors
COMPRESSOR
MOTOR

OPTIVIEW
CONTROL CENTER

J2 H2

B1,5

EVAP

CONDENSER

E C A D
G2 F2 M
(EVAP) (EVAP) (SHIPPING WIDTH)
7”

K1 COMPRE SS OR, EVAPORATOR-CONDENSER S HELL CODES

K-K M-M N-N P-P Q-Q
A 2299 2616 2616 2781 2781 ADDITIONALOPERATING HEIGHT CLEAR -
ANCE
B 2921 3454 3454 3493 3493 TYPE OF CHILLER MOUNTING M
C 641 724 724 749 749 NEOPRENE PAD ISOLATORS 44
D 508 584 584 641 641 SPRING ISOLATORS 1" DEFLECTION 25
E 4267 4267 4877 4267 4877 DIRECT MOUNT 19

K2 COMPR., EVAPORATOR-CONDENSER S HELL CODES K3 COMPR., EVAP.-COND. SHELL CODES

M-M N-N P-P Q-Q N-N Q-Q R-R
A 2616 2616 2781 2781 A 2616 2781 2972
B 3454 3454 3480 3480 B 3251 3505 3607
C 724 724 749 749 C 724 749 813
D 584 584 641 641 D 584 641 699
E 4267 4877 4267 4877 E 4877 4877 4877

K4 COMPRE SS OR, EVAPORATOR-CONDENSER S HELL CODES K7 COMPR., EVAP.-CONDSHELL CODES

R-R S-S S-V X-T X-X W-W Z-Z
A 2972 2972 3124 3302 3429 A 3124 3429
B 3632 3632 3759 3759 3759 B 3708 3912
C 813 813 813 902 902 C 813 902
D 699 699 749 749 813 D 749 813

NOTES:
1. All dimensions are approximate. Certified dimensions are available on request.
2. For all water boxes (compact shown above), determine overall unit length by adding water box depth to tube sheet length.
3. Water nozzles can be located on either end of unit. Add 13 mm to nozzle length for flanged connections.
4. To determine overall height, add dimension "M" for the appropriate isolator type.
5. Use of motors with motor hoods may increase overall unit dimensions.
6. Tubesheets are provided with jacking point notches on P and larger shells.

GB 9-3
035-19569-101 (0109)

9.2 Dimensions - Evaporator Compact Water Boxes

F F

ONE PASS EVAPORATORS, CODES

DIM. A C,D E,F G,H J,K,L M,N P,Q R,S,W X,Z
F 362 381 394 400 445 600 600 625 654

G
F

TWO PASS EVAPORATORS, CODES

DIM. A C,D E,F G,H J,K,L M,N P,Q R,S,W X,Z
F 362 381 394 400 445 600 600 625 654
G 165 178 191 197 241 397 397 425 451

F F

THREE PASS EVAPORATORS, CODES

DIM. A C,D E,F G,H J,K,L M,N P,Q R,S,W X,Z
F 362 381 394 400 445 600 600 625 654

9-4 GB
 035-19569-101 (0109)

9.3 Nozzle Arrangements - Evaporator Compact Water Boxes

A to K Evaporators
1-PASS
FRONT
OF NOZZLE
EVAP. UNIT EVAP. ARRANGEMENTS
NO. OF EVAPORATOR
A H PASSES IN OUT
A H
AA AA 1
H A

M C C M
COMPRESSOR END FLOOR LINE MOTOR END

2-PASS
FRONT
EVAP. OF EVAP.
UNIT NOZZLE
B J ARRANGEMENTS
NO. OF EVAPORATOR
DD C K DD PASSES IN OUT
BB BB C B
2 K J
M C C M
FLOOR LINE MOTOR END
COMPRESSOR END

3-PASS
FRONT
EVAP. OF EVAP.
UNIT NOZZLE
F N ARRANGEMENTS
NO. OF EVAPORATOR
DD G P DD PASSES IN OUT
BB BB G N
3 P F
M C C M
FLOOR LINE
COMPRESSOR END MOTOR END

COMPACTWATER BOXES - 150 PSI ROUND

NOZZLE PIPE SIZE(IN) EVAPORATOR NOZZLEDIMENSIONS(MM)
CONDENSER
NO. OF PASSES 1-PASS 2-PASS 3-PASS
SHELL CODE
1 2 3 C AA5 BB 5 DD5 BB 5 DD5
A 8 6 4 394 559 356 762 356 762
C,D 10 8 6 445 610 381 838 381 838
E,F 14 10 8 483 660 406 914 406 914
G,H 14 10 8 610 699 394 1003 394 1003
J,K,L 16 12 10 641 762 432 1092 432 1092

GB 9-5
035-19569-101 (0109)

Evaporators - Compact Water Boxes - M to Z Evaporators

1 PASS
FRONT
OF
UNIT
SHELL 1 PASS
CODE IN OUT
A H
A H
M–Z
AA AA H A

M C C M
COMPRESSOR END FLOOR MOTOR END
LINE

2 PASS

FRONT
OF
UNIT SHELL 2 PA SS
CODES IN OUT
B C J K B C
C B
AA AA M–Z
J K
K J
M C C M
EE EE FLOOR EE EE

COMPRESSOR END LINE MOTOR END

3 PASS
FRONT
OF
UNIT
SHELL 3 PA SS
CODES IN OUT
? ?
F N
M–Z
AA AA N F

M C C M
FLOOR
COMPRESSOR END LINE MOTOR END

COMPACTWATER BOXES - 150PSI RECTANGULAR

NOZZLE PIPE SIZE(IN) EVAPORATOR NOZZLEDIMENSIONS(MM)
EVAP SHELL
NO. OF PASSES 1-PASS 2-PASS 3-PASS
CODE
1 2 3 C AA5 AA5 EE AA5
M,N 18 14 12 724 660 660 318 660
P,Q 18 14 12 749 679 679 318 679
QV, QT 20 16 12 749 679 679 318 679
RP,RR,RT, 20 18 14 813 789 789 381 789
R2,R4,R6,W
RQ,RS,RV, 20 18 14 813 819 819 381 819
R3,R4,R5,S
X,Z 20 18 14 902 876 876 381 876

9-6 GB
 035-19569-101 (0109)

9.4 Dimensions - Condenser Compact Water Boxes

H H

ONE PASS CONDENSERS, CODES

DIM. A C,D E,F J,K,L M,N P,Q R,S T,V,W X,Z
H 352 352 381 394 391 445 492 495 492

J
H

TWO PASS CONDENSERS, CODES

DIM. A C,D E,F J,K,L M,N P,Q R,S T,V,W X,Z
H 352 352 381 394 391 445 492 495 492
J 149 165 178 191 197 241 298 279 279

H H

THREE PASS CONDENSERS, CODES

DIM. A C,D E,F J,K,L M,N P,Q R,S T,V,W X,Z
H 352 352 381 394 391 445 492 495 492

GB 9-7
035-19569-101 (0109)

9.5 Nozzle Arrangements - Condenser Compact Water Boxes

FRONT
OF UNIT
1-PASS

NOZZLE
P Q ARRANGEMENTS

NO. OF COND.
CC CC PASSES IN OUT
FLOOR P Q
COND. COND. 1
LINE Q P

M D D M
COMPRESSOR END MOTOR END

FRONT
OF UNIT
2-PASS

S U
NOZZLE
ARRANGEMENTS
R T
DD DD NO. OF COND.
PASSES IN OUT
BB BB
FLOOR R S
2
COND. LINE COND. T U

M D D M

COMPRESSOR END MOTOR END

FRONT
OF UNIT 3-PASS
NOZZLE
W Y
ARRANGEMENTS
V X NO. OF COND.
DD DD PASSES IN OUT
V Y
BB BB 3
FLOOR X W
COND. LINE COND.

M D D M
COMPRESSOR END MOTOR END

COMPACTWATER BOXES - 150 PSI ROUND

NOZZLE PIPE SIZE(IN)
CONDENSER
NO. OF PASSES 1-PASS 2-PASS 3-PASS
SHELL CODE
1 2 3 D CC5 BB 5 DD5 BB 5 DD5
A 10 6 6 381 711 546 876 546 876
C,D 12 8 6 394 762 568 956 568 956
E,F 14 10 8 445 813 603 1022 603 1022
J,K,L 16 10 10 508 914 686 1143 686 1143
M,N 20 14 10 584 1067 772 1362 772 1362
P,Q 20 16 14 641 1118 787 1448 787 1448
R,S 20 18 14 699 1181 851 1511 851 1511
T,V,W 24 18 16 749 1207 838 1575 838 1575
X,Z 24 20 16 813 1251 845 1657 845 1657
NOTES:
1. Standard water nozzles are furnished as welding stub-outs with Victaulic grooves, allowing the option of welding, flanges, or use of Victaulic
couplings. Factory-installed, class 150 (ANSI B16.5, round slip-on, forged carbon steel with 1.6 mm raised face), water flanges nozzles are
optional (add 13 mm to nozzle length). Companion flanges, nuts, bolts, and gaskets are not furnished.
2. One, two and three pass nozzle arrangements are available only in pairs shown and for all shell codes. Any pair of evaporator nozzles may
be used in combination with any pair of condenser nozzles.
3. Evaporator and condenser water must enter the water box through the bottom connection to achieve rated performance.
4. Connected piping should allow for removal of compact water boxes for tube access and cleaning.
5. Add dimension "M" as shown on the unit dimensions page for the appropriate isolator type.
6. Standard 150 psi (1034 kPa) design pressure water boxes shown.

9-8 GB
 035-19569-101 (0109)

9.6 Dimensions - Evaporator Marine Water Boxes

1-PASS
FRONT OF UNIT FRONT OF UNIT
C C C C

IN 1 6 OUT 1 6 IN
OUT

P P

COMPRESSOR END M MOTOR END FLOOR LINE COMPRESSOR END MOTOR END FLOOR LINE
M

2-PASS
FRONT OF UNIT FRONT OF UNIT
R C C R

8 OUT 3 OUT

IN
IN P P
7 2
Q Q

COMPRESSOR END MOTOR END FLOOR LINE COMPRESSOR END M MOTOR END FLOOR LINE
M

FRONT OF UNIT 3-PASS FRONT OF UNIT

C R C R C

4 10
OUT OUT

IN
P IN P
9 5
Q Q

COMPRESSOR END M MOTOR END FLOOR LINE COMPRESSOR END MOTOR END FLOOR LINE
M

CONDENSER SHELL CODE MARINE WATER BOXES - 150 PSI ROUND

NOZZLE PIPE SIZE(IN)
EVAP SHELL 1-PASS 2-PASS 3-PASS
NO. OF PASSES
CODE
1 2 3 C P5 P5 Q5 R P5 Q5 R
A 8 6 4 394 1092 1092 279 387 1092 279 387
C,D 10 8 6 445 1194 1194 254 470 1194 254 470
E,F 14 10 8 495 1295 1295 279 546 1295 279 546
G,H 14 10 8 610 1407 1407 267 597 1407 267 597
J,K,L 16 12 10 641 1534 1534 267 673 1534 267 673
M,N 18 14 12 724 1740 1740 356 673 1740 356 730
P,Q 18 14 12 749 1832 1832 381 775 1832 381 775
QT,QV 20 16 12 749 1832 1832 419 775 1832 419 775
R,S 20 18 14 813 1978 1978 -57 918 1978 -57 918
W 20 18 14 813 1978 1978 -57 918 1978 -57 918
X,Z 20 18 14 902 2169 2169 540 933 2169 540 933

GB 9-9
035-19569-101 (0109)

9.8 Nozzle Arrangements - Evaporator Marine Water Boxes

EVAPORATOR
1-PASS
IN OUT
1 6
6 1

EVAPORATOR
2-PASS
IN OUT
EVAP SHELL 1-PASS 2-PASS 3-PASS
2 3
CODE F I F G I F I
7 8
A 483 222 432 165 197 432 197
C,D 578 270 524 178 241 524 241
E,F 654 308 559 191 260 559 260
G,H 660 302 572 286 260 572 260
J,K,L 686 314 597 241 268 597 267
M,N 762 343 660 308 292 660 292
P,Q 762 343 660 343 292 660 292
QT,QV 813 368 711 343 318 711 318
R,S,W 813 371 762 368 346 762 346
EVAPORATOR X,Z 838 371 762 394 346 762 346
3-PASS
IN OUT
5 10
9 4

NOTES:
1. All dimensions are approximate. Certified dimensions are available upon request.
2. Standard water nozzles are Schedule 40 pipe size, furnished as welding stub-outs with Victaulic grooves, allowing the option of welding, flanges,
or use of Victaulic couplings. Factory-installed, class 150 (ANSI B16.5, round slip-on, forged carbon steel with 1.6 mm raised face), water flanged
nozzles are optional (add 13 mm to nozzle length). Companion flanges, nuts, bolts, and gaskets are not furnished.
3. One-, two-, and three-pass nozzle arrangements are available only in pairs shown and for all shell codes. Any pair of evaporator nozzles
may be used in combination with any pair of condenser nozzles. Compact water boxes on one heat exchanger may be used with Marine
Water Boxes on the other heat exchanger.
4. Water must enter the water box through the bottom connection to achieve rated performance.
5. Add dimension "M" as shown on the unit dimensions page for the appropriate isolator type.

9-10 GB
 035-19569-101 (0109)

9.8 Dimensions - Condenser Marine Water Boxes

FRONT OF UNIT FRONT OF UNIT
D D 1-PASS D D

IN 11 OUT 16 OUT 11 IN 16

S S

CL CL CL

FLOOR FLOOR
M LINE M M LINE M
COMPRESSOR END MOTOR END COMPRESSOR END MOTOR END

FRONT OF UNIT 2-PASS FRONT OF UNIT

D D

18 OUT 13 OUT

IN
IN
S 17 12 S

T T CL
CL

FLOOR U FLOOR
M U M M M
LINE LINE
COMPRESSOR END MOTOR END COMPRESSOR END MOTOR END

3-PASS FRONT OF UNIT

FRONT OF UNIT D D
D D

20 OUT
OUT 14

IN IN

15 S S 19

T T
CL CL CL CL

FLOOR FLOOR U
M U M M LINE M
LINE
COMPRESSOR END MOTOR END COMPRESSOR END MOTOR END

MARINE WATER BOXES - 150 PSI ROUND

NOZZLE PIPE SIZE(IN)
CONDENSER 1-PASS 2-PASS 3-PASS
NO. OF PASSES
SHELL CODE
1 2 3 D S5
S 5
T
5
U S5
T5 U
A 10 6 6 381 1194 1194 508 391 1194 508 391
C,D 12 8 6 394 1295 1295 508 470 1295 508 470
E,F 14 10 8 445 1397 1397 559 533 1397 559 533
J,K,L 16 10 10 508 1549 1549 533 546 1549 533 546
M,N 20 14 10 584 1775 1775 711 648 1775 711 648
P,Q 20 16 14 641 1889 1889 724 749 1889 724 749
R,S 20 18 14 699 2007 2007 775 826 2007 775 826
T,V,W 24 18 16 749 2089 2089 762 864 2089 762 864
X,Z 24 20 16 813 2184 2184 806 902 2184 806 902

GB 9-11
035-19569-101 (0109)

9.8 Nozzle Arrangements - Condenser Marine Water Boxes

?
CONDENSER
1-PASS
IN OUT
11 16
16 11
TUBE TUBE
SHEET SHEET

J (2-PASS
H RETURN HEAD)

CONDENSER
2-PASS
IN OUT
12 13
17 18

CONDSHELL 1-PASS 2-PASS 3-PASS

CODE H K H J K H K
A 533 251 425 152 197 425 197
C,D 610 283 495 162 229 495 229
E,F 622 292 565 178 251 565 251
CONDENSER J,K,L 686 318 584 191 260 584 260
3-PASS M,N 813 378 660 203 305 660 305
IN OUT P,Q 813 368 711 241 318 711 318
15 20 R,S 813 368 762 305 343 762 343
19 14 T,V,W 914 419 762 279 343 762 343
X,Z 914 422 813 279 371 813 356

NOTES:
1. All dimensions are approximate. Certified dimensions are available upon request.
2. Standard water nozzles are Schedule 40 pipe size, furnished as welding stub-outs with Victaulic grooves, allowing the option of welding,
flanges, or use of Victaulic couplings. Factory-installed, class 150 (ANSI B16.5, round slip-on, forged carbon steel with 1.6 mm raised face),
water flanged nozzles are optional (add 13 mm to nozzle length). Companion flanges, nuts, bolts, and gaskets are not furnished.
3. One-, two-, and three-pass nozzle arrangements are available only in pairs shown and for all shell codes. Any pair of evaporator nozzles
may be used in combination with any pair of condenser nozzles. Compact water boxes on one heat exchanger may be used with Marine
Water Boxes on the other heat exchanger.
4. Condenser water must enter the water box through the bottom connection for proper operation of the sub-cooler to achieve rated performance.
5. Add dimension "M" as shown on the unit dimension page for the appropriate isolator type.

9-12 GB
 035-19569-101 (0109)

9.9 Unit Weights

9.9.1 Approximate Unit Weight Including Motor

EST. REFRIGERANT CHARGE
SHELLS COMPRESSOR SHIPPING WEIGHT (KGS.) OPERATING WEIGHT (KGS.)
(KGS.)
A-A Q3 5,942 6,804 367
C-C Q3, Q4 6,768 8,138 562
C-C Q5 6,954 8,324 562
D-D Q3, Q4 7,809 9,571 762
D-D Q5 7,995 9,757 762
E-E Q3, Q4 8,142 10,052 776
E-E Q5,Q6,Q7,P7 8,328 10,238 776
F-F Q5,Q6,Q7,P7 8,491 10,832 987
G-E P8 9,208 10,977 903
H-F P8,P9 10,478 12,701 1,184
J-J P8,P9 10,886 13,200 1,157
L-L P8,P9 12,429 15,377 1,436
K-K H9 12,941 16,329 1,327
K-K K1 14,107 16,420 1,473
M-M H9 15,513 19,777 1,662
M-M K1,K2 17,373 21,364 1,662
N-N K1,K2 18,549 23,043 1,916
N-N K3 21,773 24,540 1,916
P-P K1,K2 18,824 23,542 1,749
Q-Q K1,K2 20,548 25,764 1,930
Q-Q K3 20,865 27,307 1,930
R-R K3 23,950 31,888 2,114
R-R K4 24,041 32,024 2,170
S-S K4 26,762 34,609 2,241
S-V K4 27,261 36,877 2,495
X-T K4 26,853 36,288 2,438
X-X K4 29,937 39,463 2,665
W-W K7 36,061 47,174 3,472
Z-Z K7 36,515 47,628 3,168

REFRIGERANT CHARGE QUANTITY ANDWEIGHTS WILL VARY BASED ON TUBE COUNT.

Refer to product drawings for detailed weight information.

GB 9-13
035-19569-101 (0109)

9.9.2 Evaporator Marine Water Box Weights

Add weights in table below to standard unit weights given in 9.9.2.
SHIPPING WEIGHT OPERATING WEIGHT
EVAP. CODE INCREASE - KGS . INCREASE - KGS .
1-PASS 2-PASS 3-PASS 1-PASS 2-PASS 3-PASS
A 419 337 444 666 584 690
C,D 613 505 671 1,009 901 1,067
E,F 852 572 943 1,532 1,252 1,624
G,H 550 588 587 1,204 1,242 1,241
J,K,L 794 836 842 1,753 1,794 1,800
M,N 1,946 924 1,878 3,418 1,481 2,858
P,Q 2,115 1,021 2,107 3,514 1,581 3,353
R,S,W 2,179 1,225 2,228 3,866 2,048 3,714
X,Z 3,215 1,660 3,286 5,240 2,498 5,100

9.9.3 Condenser Marine Water Box Weights

Add weights in table below to standard unit weights given in 9.9.2.
SHIPPING WEIGHT OPERATING WEIGHT
COND. CODE INCREASE - KGS . INCREASE - KGS .
1-PASS 2-PASS 3-PASS 1-PASS 2-PASS 3-PASS
A 346 257 367 578 489 600
C,D 429 353 474 767 691 813
E,F 329 368 359 606 781 772
J,K,L 467 529 522 1,047 1,110 1,103
M,N 1,119 603 1,054 2,206 1,110 2,078
P,Q 1,678 843 1,702 2,976 1,421 2,717
R,S 1,726 883 1,796 3,020 1,449 2,881
V,T,W 2,357 1,163 2,361 4,155 1,820 3,728
X,Z 2,649 1,339 2,440 4,491 2,109 3,674

9-14 GB
 PT ZT
042 040

GB
1 YORK CLIENT YORK
CUSTOMER

MAIN COMPONENTS PSV PSV

011 012
1 Compressor
2 Motor
3 Condenser PRV ZSL
010 010
4 Subcooler
2
5 Evaporator
PT
6 Oil cooler 010
PW
7 Oil sump 010 S10
8 Oil filter TE
092
11 Eductor
13 Drier filter +6 °C
SG
010 5
WATER

OY TE
040 13 010 +12 °C
YORK CLIENT YORK
CUSTOMER TE TE
031 091 YORK CLIENT
PSV PSV CUSTOMER
031 032 11
9.10 Process and Instrumentation Diagram

PSH
030

PT
030
8 INSTRUMENTATION
PW LCV Expansion valve
030 6 LT Level transmitter
TE
094 MPH Oil motor pump
S32
+32 °C
OH Oil heater
OY Solenoid valve
SG
3-4 030 PRV Prerotation vanes

WATER
TCV PT Pressure transducer
030
+27 °C
PT PSH High pressure cut out
041 7
TE PSV Safety valve
CLIENT YORK 093
CUSTOMER LT PW Pressure tapping
OH TSH
030 040 040 SG Sight glass
VALVES SG SG TE Temperature sensor
041 042 MPH
S10 Service valves for TE 8 040 TCV Thermostatic valve
TE
032 040 LCV TSH Temperature safety
S31 refrigerant charging / 030
S32 removing ZSL PRV closed position switch
S31
ZT Bearing proximity probe

The P & I Diagram may vary according to the compressor and the options. This one is only an example based on a chiller with H5 compressor and without any options.
035-19569-101 (0109)

9-15
035-19569-101 (0109)

Page Left Intentionally Blank

9-16 GB
 035-19569-101 (0109)

10 SPARE PARTS

When ordering spare parts, we will require the following

information to ensure the correct parts are supplied:

Full unit model number, serial number, application and

details of the parts required.

All requests for parts should be made to your local York

Sales and Service Centre.

GB 10-1
035-19569-101 (0109)

Page Left Intentionally Blank

10-2 GB
 035-19569-101 (0109)

11 DE-COMMISSIONING, DISMANTLING AND DISPOSAL

Never release refrigerant to the atmosphere Packaged units can generally be removed in one piece
when emptying the refrigerating circuits. after disconnection as above. Any fixing down bolts
Suitable retrieval equipment must be used. should be removed and then the unit should be lifted
WARNING If reclaimed refrigerant cannot be re-used. from position using the points provided and equipment
It must be returned to the manufacturer. of adequate lifting capacity.

Never discard used compressor oil, as it Reference should be made to Section 4 for unit
contains refrigerant in solution. Return installation instructions, Section 9 for unit weights and
used oil to the oil manufacturer. Section 3 for handling.
WARNING

Units which cannot be removed in one piece, after

Unless otherwise indicated the operations described disconnection as above, must be dismantled in position.
below can be performed by any properly trained Special care should be taken regarding the weight
maintenance technician. and handling of each component. Where possible
units should be dismantled in the reverse order of
11.1 General installation.

Isolate all sources of electrical supply to the unit Residual solution, refrigerant, oil and glycol or
including any control system supplies switched by the similar fluids may remain in some parts of the
unit. Ensure that all points of isolation are secured in system. These should be mopped up and disposed
the "OFF" position. The supply cables may then be of as described above.
disconnected and removed. For connection points refer
to Section 4. It is important to ensure that whilst components are
being removed the remaining parts are supported in a
Remove all refrigerant from the unit into a suitable safe manner.
container using a refrigerant reclaim or recovery unit.
This refrigerant may then be re-used, if appropriate, Only use lifting equipment of adequate
or returned to the manufacturer for disposal. Under capacity.
NO circumstances should refrigerant be vented to
WARNING
atmosphere. Drain the oil from the unit into a suitable
container and dispose of according to local laws and
regulations governing the disposal of oily wastes. Any After removal from position the unit parts may be
spilt oil should be mopped up and similarly disposed disposed of according to local laws and regulations.
of.

Isolate the unit heat exchangers from all external water

systems and drain the heat exchanger sections of the
system. If no isolation valves are installed it may be
necessary to drain the complete systems.

If glycol or similar solutions have been

used in the water system(s), or Chemical
additives are contained, the solution MUST
WARNING be disposed of in a suitable and safe
manner. Under NO circumstances should
any system containing glycol or similar
solutions be drained directly into domestic
waste or natural water systems.

After draining, the water pipework can be disconnected

and removed.

GB 11-1
035-19569-101 (0109)

Page Left Intentionally Blank

11-2 GB
 www.johnsoncontrols.com

035-19569-101 (0109) Subject to change without notice.

ALL RIGHTS RESERVED