Electronic Railway Control and Safety System: Iarjset

ISSN (Online) 2393-8021
IARJSET ISSN (Print) 2394-1588
International Advanced Research Journal in Science, Engineering and Technology

ICRAESIT - 2015
B V Raju Institute of Technology, Narsapur
Vol. 2, Special Issue 2, December 2015
Electronic Railway Control and Safety System

Simpi Kumari1, Syed Abudhagir .U2
Student, Dept of Electronics Communication Engineering, B.V. Raju Institute of Technology, Narsapur, Telangana1
Associate Professor, Department of Electronics Communication Engineering, B.V. Raju Institute of Technology,
Narsapur, Telangana2
Abstract: Integrating features of all the hardware components used have been developed in it. Presence of every
module has been reasoned out and placed carefully, thus contributing to the best working of the unit. Secondly, using
highly advanced IC’s with the help of growing technology. In this work, Electronic Railway Control and Safety System
(EMRCS) has been successfully designed, implemented and tested. We mainly intended to protect the passengers of
train using fire sensors and automatic control the unmanned level crossing gate from long distance. Electronic Railway
Control and Safety System (EMRCS) has been successfully designed, implemented and tested. This paper aims in
detection of occurrence of fire in railways. Fire detection should be taken place in right time to avoid damage. The fire
extinguishers like sprinkling water; air coolants etc can be automatically operated.
Keywords: Railway Safety, Fire detection, ERCS System, PIC16F876A.
I. INTRODUCTION
An embedded system is a combination of software and hardware to perform a dedicated task. Some of the main devices
used in embedded products are Microprocessors and Microcontrollers.
This work deals Electronic Railway Control and Safety System using PIC16F876 Microcontroller. It is an exclusive
work that can provide security at railways according to the instructions given by the above said microcontroller. Further
the implementation of Unmanned Railway Gate using PIC16F876A microcontroller [1, 2] is explained.
In this paper, we presented a model which can be detected the occurrence of the fire without any delay successfully and
the fire extinguishers like sprinkling water; air coolants etc can be automatically operated. The system alerts through
SMS message to a control station using GSM modem, so that they act immediately with the necessary actions. Hence,
the accidents taking place due to fire in the locomotives can be controlled. Further, the objective of this paper is to
provide an automatic railway gate opening and closing at a level crossing replacing the gates operated by the
gatekeeper. It deals with two things. Firstly, it deals with the reduction of time for which the gate is being kept closed.
Secondly, it increases the safety of road users by reducing the accidents.
The paper explains the implementation of “Electronic Railway Control System” using PIC16F876 microcontroller and
PIC16F877A. The organization of the paper is explained here, section 2 is presented, the ERCS Systems hardware and
software modules. In the same section the explanation of microcontrollers, GSM modem, LCD, fire sensor, buzzer,
firefighting equipment, are considered. And also it presented the software description. It explains the implementation of
the module using PIC C Compiler software. Section 3 is discussed results and section 4 is concluded the work.
II. ERCS SYSTEM
Our paper is implemented with the help of fire sensor, GSM modem, LCD and also firefighting equipment. We employ
fire sensors to sense the presence of fire which detects the fire. The output of the fire sensor is fed as input to the micro
controller. Whenever fire is detected the sensor communicates the message with the central control station along with
the automatic operation of extinguishers in which the fire aroused.
The microcontroller is responsible for receiving the information sent by different sensors like fire sensor, detection
sensor and when it receives information for presence of fire it then displays the same on the LCD and alerts through
SMS message to the control station using GSM modem. The firefighting equipment is operated automatically when the
fire has been detected.
By employing the automatic railway gate control at the level crossing the arrival of the train is detected by the sensor
placed near to the gate. Hence, the time for which it is closed is less compared to the manually operated gates and also
.Copyright to IARJSET DOI 10.17148/IARJSET 176


ICRAESIT - 2015
reduces the human labor. This type of gates can be employed in an unmanned level crossing where the chances of
accidents are higher and reliable operation is required. Since, the operation is autonomous error due to manual
operation is prevented.
The fig 2.1 is shown that block diagram of ERCS using GSM. It explains the interfacing section of each component
with micro controller and GSM module. The temperature sensors are used in this work to detect the temperature, once
the temperature rises above 80 degrees; the buzzer sound alerts the passengers and the locomotive driver. The LCD
display present near the locomotive driver shows the temperature reading inside the compartment. Once the
temperature rises above 80 degrees automatic water pumping system will be implemented and message is sent to the
nearby control stations, using GSM module.
The temperature sensor records the temperature and sends the value to ADC and ADC sends the digital output to the
microcontroller. Microcontroller compares the threshold value and the given input and switches on the buzzer driver,
LCD driver, relay driver and GSM accordingly. The relay driver switches on the firefighting equipment i.e. the
automatic pumping of water. Microcontroller operates at the frequency range of 25 MHz; hence we use a crystal
oscillator.
The unmanned railway gate uses a pair of IR sensors and a stepper motor driver for gate operation. In this prototype
model, we detected the train when it is in 5km away from the level crossing. This distance range can be adjusted by
using pot. We used two pairs of IR sensors, one for entry and one for exit. Using H bridge circuit, the clockwise and
anti-clockwise switching of gate operation for the motor is done. By employing the automatic railway gate control at
the level crossing the arrival of the train is detected by the sensor placed near to the gate. Hence, the time for which it is
closed is less compared to the manually operated gates and also reduces the human labour. This type of gates can be
employed in an unmanned level crossing where the chances of accidents are higher and reliable operation is required.
Since, the operation is automatic; error due to manual operation is prevented.
III. RESULT AND DISCUSSIONS
In this work, hardware and software module has been implemented successfully and matched the expected results.
Fig 2.1 Block diagrams of ERCS system


ICRAESIT - 2015
3.1 Observations:
Fig3.1. Images of working of Temperature Sensors
The above fig 3.1 shows that the measured temperature in LCD display. Heat senor is heated by soldering iron. The
measured temperature is displayed in mobile phone by using GSM module shown in fig 3.2.
Fig3.2. Images of temp displays in Cell phone
Fig 3.3 Images of Water pumping system
Fig 3.4 Images of Unmanned Level crossing


ICRAESIT - 2015
The above fig 3.3 shows that when the temperature exceeds prescribed value then the water pumping system is spread
the water in the cabin. The working model of unmanned level crossing system is shown in fig 3.4.
4. CONCLUSION
Our paper is implemented with the help of fire sensor, GSM modem, LCD and also firefighting equipment. We employ
fire sensors to sense the presence of fire which detects the fire. The output of the fire sensor is fed as input to the micro
controller. Whenever fire is detected the sensor communicates the message with the central control station along with
the automatic operation of extinguishers in which the fire aroused.
The system must be capable of sensing the train arrival and it should automatically close the gate. Also, the system
should sense the train departure and automatically reopen the gate.
This work can be extended using laser and LDR (Light Dependent resistor) which gives better performance than IR
sensors used in the paper. And also it can be extended by using gas sensor, humidity sensor, GPRS and 3G
technologies.
ACKNOWLEDGEMENT
This work is fully supported by Department of ECE, B.V. Raju Institute of Technology, Narsapur, Telangana. We are
very grateful to our college managements, department head, supervisor and teaching and non-teaching staff members.
REFERENCES
[1] Raj Kamal (2009), Microcontrollers: Architecture, Programming, Interfacing and System Design, 2nd. Ed. Pearson Edu.
[2] Mazidi and Mazidi (2007) – The 8051 Microcontroller And Embedded Systems Using Assembly And C, 2nd. Ed. Pearson Edu.
[3] Xiaoning, J.; Kyungrim, K.; Shujun, Z.; Joseph, J.; Giovanni, S., (2014). High-Temperature Piezoelectric Sensing.Sensors.,14(11), 144-169.
[4] PIC16F876A datasheet - ww1.microchip.com/downloads/en/DeviceDoc/39582b.pdf.

Electronic Railway Control and Safety System: Iarjset

Uploaded by

Copyright:

Available Formats

Electronic Railway Control and Safety System: Iarjset

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Electronic Railway Control and Safety System: Iarjset

Uploaded by

Copyright:

Available Formats

ISSN (Online) 2393-8021

IARJSET ISSN (Print) 2394-1588

International Advanced Research Journal in Science, Engineering and Technology