Operator’s Manual

G-320D
Contents
Contact Information..................................................................................................................................................4

1.0 GENERAL INFORMATION ............................................................................................. 5

1.1 Warranty Information ...........................................................................................................................................5
1.2 Return Policy .......................................................................................................................................................5
1.3 Damaged Shipments ...........................................................................................................................................5
1.4 Liability .................................................................................................................................................................6
1.5 Customer Service and 24/7 Technical Support....................................................................................................6
1.5.1 Contact Information and Additional Support: ....................................................................................................6

2.0 SAFETY .......................................................................................................................... 7

2.1 Special Symbols ..................................................................................................................................................7
2.2 Safety Rules ........................................................................................................................................................7

4.0 MACHINE INFORMATION.............................................................................................10

4.1 Machine Diagram............................................................................................................................................... 11
4.2 G-320D Electric Machine Diagram .................................................................................................................... 12

5.0 PREPARING THE MACHINE ........................................................................................13

5.1 General .............................................................................................................................................................. 13
5.2 Adjusting The Handle ........................................................................................................................................ 13
5.3 Attaching Tooling ............................................................................................................................................... 14
5.4 Attaching the Dust Skirt ..................................................................................................................................... 15
5.5 Attaching the Vacuum Hose .............................................................................................................................. 16
5.6 Attaching the Propane Tank .............................................................................................................................. 17
5.7 Preparing to Wet Grind ...................................................................................................................................... 17

6.0 OPERATING THE MACHINE ........................................................................................18

6.1 320D- Propane Control Panel ............................................................................................................................ 18
6.2 G-320D Electric Control Panel ........................................................................................................................... 19
6.3 Starting The Propane Machine .......................................................................................................................... 20
6.4 Grinding Weights ............................................................................................................................................... 21
6.5 Wet Grinding ...................................................................................................................................................... 22

7.0 MAINTENANCE .............................................................................................................22

7.1 Cleaning The Machine ....................................................................................................................................... 22
7.2 Before Beginning Work ...................................................................................................................................... 22
7.3 Every 100 Hours of Operation ........................................................................................................................... 22
7.4 Every 200 Hours of Operation ........................................................................................................................... 23
7.5 Every 300 Hours of Operation ........................................................................................................................... 23

8.0 TROUBLESHOOTING ...................................................................................................24

8.1 Propane Machine Troubleshooting .................................................................................................................... 24
8.2 Electric Machine Troubleshooting ...................................................................................................................... 25
8.3 Replacement Parts ............................................................................................................................................ 26

9.0 ACCESSORIES .............................................................................................................27

9.1 Plates ................................................................................................................................................................. 27
 9.2 Tooling ............................................................................................................................................................... 27

10.0 MAINTENANCE INDEX..............................................................................................28

10.1 Rebuilding Flex Heads ..................................................................................................................................... 29
10.2 Oil Changes ..................................................................................................................................................... 30
10.3 Changing the Oil Filter ..................................................................................................................................... 32
10.4 Air Filter Service .............................................................................................................................................. 33
10.5 Greasing The Ring Gear .................................................................................................................................. 34
10.6 Changing The Belt ........................................................................................................................................... 35
10.7 Changing The Spark Plugs .............................................................................................................................. 35
Contact Information

Concrete Polishing Solutions

PO Box 520
Norris, TN 37828
877.472.8200
www.go2cps.com
1.0 GENERAL INFORMATION

1.1 Warranty Information

Concrete Polishing Solutions (CPS) warrants to the purchaser that under normal use and
service, the G-320D grinder purchased hereunder shall be free from defects in material and
workmanship for a period of one (1) year. Expendable or consumable items or parts (such as
belts, gaskets, or parts with wear) are not covered under this warranty. This warranty does not
cover equipment or parts which have been misused, altered, neglected, handled carelessly, or
used for purposes other than which they have been manufactured. Further, this warranty does
not cover loss, damages resulting from accident, or damages resulting from an unauthorized
service. Please note, unauthorized modifications or repairs to the machine may void this
warranty.

1.2 Return Policy

Please open and inspect your order promptly upon receipt. Should you find an issue with the
contents, please contact a member of the CPS sales and technical staff first, so they can
resolve the issue as quickly as possible.

Any returns must be made within 30 days of delivery and must be accompanied by a return
authorization number, as well as a copy of the original invoice. CPS will then review the
complaint and inspect the merchandise before a credit can be processed.

Any items that are returned because of obvious misuse will be shipped back to the sender at
their expense and no credit shall be issued.

Any returned items, including items under warranty, must be sent at the customer’s expense.
No authorization number is necessary if you are returning an item for repair that will be returned
to you after repairs.

Before you return an item, CPS asks that you first call a member of the sales and technical staff
at 877.472.8200 and provide your company name, address, telephone number, and a brief
statement explaining the problem.

If an item was delivered to you in error, please let CPS know and the item will be picked up at
CPS’ expense. If your order contains a shortage, report the shortage no later than 24 hours
after receiving your shipment. Shortage claims will be honored only when reported promptly.
CPS cannot accept any products that have been either modified to a customer’s specifications,
or is a non-stocking special order item. Any products, such as machines or other equipment that
sustain aftermarket alterations not pre-approved by CPS are not returnable.

1.3 Damaged Shipments

CPS carefully inspects all orders prior to shipment and then packs shipments as carefully as
possible. CPS advises that you thoroughly check all cartons before you sign for the order. Any
claims for merchandise damaged in transit must be filed with the delivering carrier, not CPS.
1.4 Liability
Important Notice:

The following is made in lieu of all warranties, expressed or implied. CPS and/or manufacturer’s
only obligation shall be to replace such quantity of product proved to be defective, provided that
such guarantees or replacements are a stated policy of the manufacturer. CPS and/or
manufacturers shall not be liable for any injury, loss, or damage whether direct, incidental, or
consequential, arising from the negligence or misuse of the product. Before using, user shall
determine the suitability of the product for its intended use and the user assumes all risk and
liability whatsoever in connection therewith. The foregoing may not be altered, except by an
agreement signed by at least two of the officers of Concrete Polishing Technologies, Inc. CPS
will not be liable for delays in shipping due to circumstance beyond the control of CPS.
Warranties will be null and void if after-market alterations, changes, or modifications have been
made to the equipment.

1.5 Customer Service and 24/7 Technical Support

Concrete Polishing Solutions has a well-trained service department and our sales and technical
staff have extensive knowledge on how to service our equipment. Being the manufacturer, we
best understand our equipment and already have parts in stock. We can also send you the parts
and help you to service your own equipment over the phone. In some locations, we can also
provide you with information regarding an outside service person in your area that can assist
you with parts and service.

If you do need to contact the Service Department, you will need to provide the product model
and serial numbers to the person assisting you. CPS provides technical support to our
customers twenty-four hours a day, seven days a week. Trained representatives will be happy
to help you with any questions you may have. You can reach the CPS Service Department 24/7
by calling 877.472.8200 or via email at [email protected].

1.5.1 Contact Information and Additional Support:

If you are in need of assistance, contact CPS Customer Service, day or night:
By phone: 877.472.8200
By email: [email protected]

For informational videos on CPS equipment, including instructional videos and tips for bidding
and more, visit CPS on YouTube by searching Concrete Polishing Solutions and clicking
‘Subscribe’. Follow us on Facebook at http://www.facebook.com/concretepolishingsolutions.
2.0 SAFETY

This operator’s manual provides instructions for safe, efficient, and trouble-free operation of
your machine. You and anyone else who will be using or maintaining the machine are required
to read and understand the information contained in this manual. Owners and operators must
keep the owner’s manual available for frequent reference. Contact Concrete Polishing Solutions
if you need any assistance, information, or additional copies. The G-320 machines are designed
to be used by a professional. The user is expected to have good knowledge and understanding
of the user and safety instructions before operating, inspecting, or adjusting the machine.

2.1 Special Symbols

The symbols below represent a need for extra consideration when using the G-320 Machine.

2.2 Safety Rules

It is imperative to follow all safety instructions herein, as well as ensuring that safety guidelines
are followed by anyone in the vicinity of work being done with the G-320, along with any current
workplace safety regulations or rules.

Work should only be performed by a trained professional. Each operator of the machine
should be familiar with the manual and should be aware of the risks of incorrect use or
operation.

CPS offers free training to machine operators both upon scheduled requests, as well as through
our distributors across the United States. For more information on trainings in your area, visit
http://www.go2cps.com or call 877.472.8200.
 Warning
 Training is required before operating this machine.
 Keep machine out of the vicinity of children.
 Do not allow children on or near the machine.
 Those with impaired mental, physical, or sensory
abilities should not operate the machine.

Concrete Polishing Solutions machines should be used only in the manner CPS recommends.
Anyone using the G-320 should know about:

 Machine Functions
 Emergency Stop Procedure
 Workplace Safety Rules

The operator of the machine:

 Should ensure that no unauthorized person is in the area when the machine is started.

The workplace:

 Should be suitable to using a propane grinder, including proper ventilation

 Should be free of debris and loose objects that could potentially be thrown out by the
machine
 Should be free of exposed bolts or other implements that could damage the machine or
cause injury.

Proper Personal Protective Equipment (PPE):

 Safety Goggles
 Protective Gloves
 Steel Toe Safety Shoes
 Hearing Protection
 Respiratory Mask
 Do not wear clothing that is loose-fitting, as it could become caught or snagged by the
machine, including scarves, bracelets, or rings.

Precautions:

 Be sure that propane tank and hose are free of holes and leaks and is properly attached
to the grinder at all times.
 Maintenance and service should only be performed by qualified personnel or certified
servicers.
 Access to a clearly marked fire extinguisher should be provided at all times.
 Do not perform maintenance or service on live or operational machines. Machine should
be turned off before any service or maintenance is completed.
 An electrician should be consulted to inspect any exposed wires, leads, or to open
electrical boxes on job sites. Protect yourself and others from electrical shock and
potential death by consulting an electrician. Do not attempt to repair electrical
issues with machines.
3.0 TRANSPORTATION OF YOUR MACHINE

To transport the G-320:

1. Place the handle in the upright position and lock the handle pin.
2. Carefully pull the machine back, using a foot placed on the weights to gain leverage.
3. Transport the machine using the wheels, with the machine tipped back.

Warning
 Strap down equipment securely (across non-moving parts) when
transporting from jobsite. Unsecure or unanchored equipment can cause
property damage, injury, or death.
 Be sure to place hands in the center of handlebars when lowering and
raising the machine. The placement increases stability and reduces the risk
of machine tilting and causing injury.

Tip
 Make sure machine weights are in their upright position when attempting to
transport the machine. The weights exert 150 pounds of downward
pressure when engaged, making tilting back the machine for transport
much more difficult and dangerous.

3.1 Storage

Store your CPS grinder in an area that is dry. Long exposure to cold or damp conditions can
damage the grinder.
4.0 MACHINE INFORMATION

Your G-320 machine was carefully inspected and protectively packaged to prevent damage in
shipment. We suggest that upon removing the unit from its carton, you carefully inspect it for
any possible damage in transit. Immediately notify the transportation company who delivered
your machine. CPS grinders are equipped to handle various types of jobs, including surface
preparation, grinding, and polishing of concrete flooring. The G-320 is equipped with three
grinding heads upon which plates and tooling for different applications can be attached. For
more information on CPS tooling visit http://www.go2cps.com/tooling.html

The following items should be included with the delivery of your machine. Please notify CPS if
anything is missing:

1. One (1) G-320D Grinder

2. One (1) Dust Skirt
3. One (1) Operator’s Manual

G-320D Propane
Weight: 896lbs
Grinding Pressure: 565-715lbs
Grinding Width: 32”
Power Required: Vapor Draw Propane Tank
Engine: 31 HP
RPM: 1300-3400

G-320D Electric
Weight: 896lbs
Grinding Pressure: 565-715lbs
Grinding Width: 32”
Power Required: 3-Phase/480v/30amp
Engine: 20 HP
RPM: Variable to 1800
4.1 Machine Diagram
4.2 G-320D Electric Machine Diagram
5.0 PREPARING THE MACHINE

5.1 General
The following information is intended to provide you with general instruction on how to properly
operate your G-320 machine. Be sure to follow all workplace safety regulations and rules when
operating the machine. Training in proper techniques and methods is available through CPS
and its distributors. To find a training near you and more visit www.go2cps.com

5.2 Adjusting The Handle

When adjusting the handle, first, locate the pin (circled on the drawing above). While holding the
handle bars with one hand, press the lock in and pull the pin out fully. Raise or lower the
handlebars as needed, being sure to secure the handle with the pin when the handlebars are in
the desired position.

Warning

 Whenever moving the handle of the

machine, be sure that it locks into position.
Failure to lock the handle can lead to
injury.

Tip
 When adjusting handlebars, be sure to find
a handlebar position that will give you
adequate and comfortable control of the
machine.
5.3 Attaching Tooling

The G-320 Machine is fitted with three cross-completes inside the grinding head assembly for
attaching plates and tooling.

To attach the appropriate grinding tools to the G-320:

1. Make sure the handle is in the upright “locked” position. Place hands in the center of the
handlebars when lowering and raising the machine. This method increases the control
you have when maneuvering the machine.
2. Lay the machine on its back with the handle lying on the floor. This exposes the driving
plate on the underside of the machine.
3. From a standing position at the side of the upended machine, put metal bond plate or
resin plates on the cross-complete (1). Turn the cross-complete in either direction to lock
the plate onto the machine
4. Place the tooling of choice securely onto the plates.
5. Return the machine to the upright position.

Warning
 Never kneel in front of the machine
when attaching tooling or replacing
tooling.
 Increased heating of the tooling and
equipment may occur due to grinding
speed, increase of pad diameter, or
grinding with or without water. Wear
heat-resistant gloves when changing
tooling.
 5.4 Attaching the Dust Skirt

Your G-320 machine includes a dust skirt that should be placed on the machine before machine
operation. The dust skirt is lined with velcro for easy attachment and removal from the bottom of
the safety shroud.

1. To attach the dust skirt, first locate the strip of velcro around the bottom of the safety
shroud. (See diagram on p.9)
2. Working from one side of the machine to the other, line up inner velcro on dust skirt with
velcro on safety shroud and attach the dust skirt.

Tip
 Make sure that the dust skirt is not
placed too tightly around the safety
shroud. The machine can lose suction
if the dust skirt is too tight.

Safety Shroud with

outer Velcro lining.

Dust Skirt w.
Inner Velcro
lining
5.5 Attaching the Vacuum Hose

If dry-grinding, be sure to attach the vacuum hose to your G-320 machine before beginning any
work. Follow all workplace safety requirements when wet or dry-grinding.

WARNING
 Dust from grinding can be dangerous
and damaging to the lungs. Be sure to
wear proper protective equipment to
prevent inhalation.
 If wet grinding, be sure to have a slurry
containment system in place.

To attach a dust interceptor/vacuum, locate the hose on the upper frame of the machine. (See
above diagram). Be sure to connect hoses firmly for most efficient dust interception.
5.6 Attaching the Propane Tank

Each G-320 is shipped with a vapor draw propane tank. To connect the propane tank to the
machine, be sure the propane tank is secure in its location between the safety swing arms.

1. After securing the propane tank on the machine, locate the connection hose with brass-
fitting.
2. Press down on the brass fitting connector to release any residual vapor that may be in
the line before connecting to the propane tank.
3. Tightly connect the brass fitting of the propane hose to the valve on top of the propane
tank.
4. Turn the knob to open the valve on the tank.

WARNING
 Only refill vapor draw tank to 80%.
Overfilling can cause the machine to
draw liquid, causing damage.

 Be sure to check all hoses for cracks

and leaks. Propane is an odorless
gas with a sulfur additive. If you
recognize a strong odor, immediately
turn off the valve on your tank and
contact CPS.

 Only operate in well-ventilated areas.

5.7 Preparing to Wet Grind

Each G-320D Grinder is equipped to grind wet or dry. Both the propane and electric grinders
are equipped to wet grind, using the gravity fed systems for water dispersal. When planning to
wet grind:
 Have a slurry containment system already in place.
 Be sure to follow any regulations ordinances about slurry disposal in your area. Each
municipality may have different rules regarding slurry disposal.
 Clean and dispose of concrete slurry quickly, as it thickens as it dries, making clean
up more difficult.
6.0 OPERATING THE MACHINE

G-320 Machines are designed to be simple to operate. Below are diagrams of the G-320
Propane and Electric control panels. Familiarize yourself with the controls and operating
procedures for your particular machine before starting any work.

6.1 320D- Propane Control Panel

The Start Button

The Start Button should be pressed after disengaging the emergency stop button. Upon pressing the start
button, begin to turn the throttle slowly counterclockwise until desired RPM is reached.

The Emergency Stop Button

The emergency stop button must be disengaged before starting the machine. When stopping the
machine, turn the throttle down to lower the RPM and depress the Emergency Stop button. This button
should also be depressed in case of emergency necessitating stopping the machine.

The Throttle
The throttle is located on the upper left hand side of the machine frame. When starting the machine, the
throttle must be turned slowly counterclockwise to engage the engine. Continue to turn the throttle until
the machine reaches the desired RPM.

The Tachometer
The tachometer, located on the upper frame of the grinder displays both machine hours and RPM of the
machine. The button located on the right of the face of the tachometer allows toggling between the
machine hours and RPM.
6.2 G-320D Electric Control Panel

The Run Button

The Run button turns on the main electric motor to begin machine function.

The Stop / Reset Button

Use the top part of the button, labeled “Stop” to initiate a shutdown sequence, bringing the grinding
heads to a slow stop and shutting down power to the machine. The bottom part of the button, labeled
“Reset” is used to reactivate the initial start-up sequence and is used after the “Stop” button has been
pressed. For emergency stopping, locate the large red button near the speed potentiometer. The
Emergency Stop button should be depressed to immediately stop the machine when needed.

The Forward/ Reverse Button

The forward and reverse buttons determine the direction of the head and the direction of the machine.
Pressing “FWD” causes the heads to rotate in a forward direction, while “REV” causes the machine
heads to rotate in a counterclockwise direction, moving the machine in the reverse direction.

The Speed Potentiometer.

This is a variable speed, rotating selection with parameters from 1-10, depending on how fast or how slow
you want to operate your machine.
6.3 Starting the Propane Machine

Before starting the machine, be sure to check that your work area is free of debris or other
material that could be run over by the machine.

Starting the Propane Machine

1. Adjust handlebars to desired height and grasp firmly.

2. Stand behind the machine with feet planted firmly on even ground.
3. Pull up on the ‘Emergency Stop’ button, making sure it is disengaged.
4. Press the ‘START’ button to engage the engine, while slowly turning the throttle
counterclockwise.
5. Turn the throttle to desired RPM, which is displayed on the tachometer (located on
the frame) for your convenience.
6. Weights can be lowered to increase grinding pressure, though weights need to be
returned to their upright position when attempting to change tooling or to transport.
7. To stop machine, decrease RPM by turning the throttle counterclockwise, then
depress the “Emergency Stop” button on the machine.
8. Return weights to upright position after shutting machine off. Be sure to return the
weights to their original position any time the machine needs to be laid back or
transported, such as during tooling changes.
9. Turn propane valve to the off position when finished with work and store machine as
is appropriate.

WARNING
 Be sure to run machine in a
well-ventilated area. Lack of
ventilation can cause machine
issues and are dangerous for
operators and bystanders.
 Do not start machine with
grinding head in the upright
position.
 Be sure the dust skirt is
attached before starting the
machine.

Tip
 Do not let machine idle for more than a
minute. Extended idling can cause
damage to centrifugal clutch.
 Over-torqueing the throttle in either
direction can cause throttle damage.
Starting the Electric Machine
1. Adjust handlebars to the desired height.
2. Check to be sure the dust skirt is properly attached and secured.
3. If dry grinding, hook machine hose to vacuum for dust removal.
4. Locate the power cord for your electric grinder. Plug electric cord into the receptacle
located next to the handle pin on top of the inverter box (see diagram p.)
5. Plug machine into appropriate power source.
6. Stand behind the machine with feet planted firmly.
7. Press the “Run” button (See diagram p.) to engage the power supply.
8. Turn Speed Potentiometer (See diagram p.) to the desired RPM.
9. Weights may be lowered to increase grinding weight if necessary.
10. To stop machine, press button labeled “Stop” to turn machine off.
11. After stopping machine, lower the speed potentiometer back to 0.
12. Be sure to return machine weights to their original position when
13. Disconnect the power cord from the outlet, then from the grinder.

WARNING
 Do not start machine with grinding
head in the upright position.
 Be sure the dust skirt is attached
before starting the machine.
 Always use a three-wire electrical
system connected to the electrical
ground.
 For maximum electric shock protection,
use a circuit protected by a ground
fault circuit interrupter.

6.4 Grinding Weights

The grinding weights on the CPS G-320 Grinder are designed to maximize grinding pressure
when necessary. Weights are located above the shroud on both sides of the machine (See p.9)
and are approximately 75 lbs per weight for a total of 150 lbs additional grinding pressure.

Weights may be lowered when needed by grasping the handle on the weights and pulling them
forward. To replace weights, lift by handle and return to original position.

WARNING
 Weights are pinch-points. Be careful
when moving to keep fingers from
being smashed.
 Do not attempt to transport the
machine with weights engaged.
Return weights to their original
position before transport.
6.5 Wet Grinding
To use gravity-fed water dispersal on the G-320D, be sure the water tank is filled with water.
Locate the water release valve and open to let gravity-fed system begin to release water.

7.0 MAINTENANCE

CPS Machines are meant to be low-maintenance for the owner/operator, though there are some
important routine maintenance that should be done. See the Maintenance Checklist in the
Maintenance Index (located in the back of this manual) for more information. Be sure to follow
all workplace safety procedures when performing maintenance.

7.1 Cleaning The Machine

The CPS G-320 should be cleaned after each use to ensure continued functionality.

WARNING
 Do not use chemicals or solvents to
clean the machine. Harsh
chemicals can cause damage to
the inner workings of the machine.
 When wet grinding, be sure to
clean machine of slurry thoroughly
before storing.

7.2 Before Beginning Work

Your machine should be checked before beginning each new project.

 Check oil levels. Oil should read as full before beginning work.
- Use only SAE 30W Engine Oil in the G-320D Propane machine.
 Check the belt. Examine the belt for any signs of wear and tear.
 Check that the cooling system air inlet is clean. Located on the engine, the cooling
system air inlet should be checked every before operation to clear it of debris and dust.

7.3 Every 100 Hours of Operation

 Change the oil. Oil should be changed after the first 8 hours of use and every 100 hours
after that. Use only SAE 30W Engine Oil in the G-320D Propane machine.
 Change the spark plugs.
 Clean the cooling system. The engine cooling system should be free of debris and
dust.
 Clean oil cooler fins. The oil cooler fins should be cleaned every 100 hours to ensure
they are free of debris and dust and cooling effectively.
  Tighten nuts and screws. The engine should be checked for loose nuts and screws
regularly, with special attention to tightening every 100 hours of operation.

7.4 Every 200 Hours of Operation

 Change the oil filter. The oil filter should be checked regularly to ensure it is not dirty. If
filter appears dirty, replace with new clean filter. Filter should not be cleaned for reuse.
See p. for instructions.
 Change the fuel filter. The fuel filter should be changed every 200 hours. If the filter
appears dirty, replace with a new clean filter. The filter cannot be disassembled, so new
parts must be ordered for replacement.
 Change the primary air filter element. The air filter primary element should be
replaced after 200 hours of use.
 Change the belt. The belt should be replaced with a new belt every 200 hours, or when
wear and tear becomes apparent.

7.5 Every 300 Hours of Operation

 Grease the ring gear. The ring gear should be greased every 300 hours of operation.
 Check the Secondary Element. The secondary element should be replaced when dirty,
or after 500 hours, whichever comes first.
8.0 TROUBLESHOOTING

8.1 Propane Machine Troubleshooting

The G-320D Propane grinder from Concrete Polishing Solutions is designed to be inherently
low-maintenance and to perform for long periods without extensive troubleshooting in the field. If
difficulty is encountered, refer to the following:

Symptoms
Failure to Start  Ensure there is adequate propane in the tank
 Ensure the E-Stop button is disengaged.
 Check the battery for a charge.
 Check to ensure the oil level is correct.
 Check the speed you are starting at. Start at a low speed and slowly
build to higher RPMs.

Stops Suddenly  Ensure there is adequate propane in the tank

 Make sure the tank is not overfilled. (80% full maximum)
 Make sure you are using a vapor draw tank. CPS machines will not
function with any other propane tank.
 Be sure that exhaust is not covered or blocked.
 Ensure there is adequate ventilation.
Vacuum Not  Check that hoses are fastened securely and that vacuum is functional.
Working

 Check belt tension.

Head Does Not Turn  If the engine is running and the head does not turn, contact CPS for
certified service providers who can assist you.

 If the heads spin, but the housing doesn’t, it’s likely that a pinion gear
shear pin has broken.
Heads Spin,
Housing Doesn’t  Test to see if shear pin has broken by turning one of the heads while the
machine is shut off. The housing should turn if the machine is functional.
If it isn’t call CPS to find a certified service provider to assist you.
 Turn machine off.
 Tilt machine to check evenness of heads.
 If the heads are not running evenly, rebuild heads.
Machine is Vibrating
or Running  Check for uneven wear on diamonds.
Unevenly  Check that the grinding tools are not worn down and that they are
properly positioned on the wheel.
 A concentration of dirt causes the driving plates to become hard and
inelastic. Clean the machine between the housing and heads.

Should you still have difficulty, contact CPS at 877.472.8200 for assistance, 24/7.
8.2 Electric Machine Troubleshooting
Symptoms
Failure to Start  Ensure that the power cord is securely plugged in.
 Make sure the prongs on the cord are making good contact with the
outlet.
 Check that all phase indicator diodes are lit up.
 Check the speed you are starting on.
 Press Reset if the Stop button was pressed.

Stops Suddenly  Check to see if the cable is hot. If it is hot, the cable may be too long
or have too small a cross-sectional area.
 Reduce speed. The machine may have been continuously run at
high speed with an inefficient electrical supply.
Vacuum Not Working  Check that hoses are fastened securely and that vacuum is
functional.

 Check belt tension.

Head Does Not Turn  If the fan on the engine is running but the head is not turning, the belt
is slipping or broken. Call CPS for service.

 If the heads spin, but the housing doesn’t, the pinion gear shear pin
Heads Spin, Housing has broken. Test it by turning one of the heads manually. The
Doesn’t housing should tun.

 Check for uneven wear on diamonds. If the heads are not running
evenly, rebuild Flex Heads.
Machine is Vibrating or  A concentration of dirt can cause the driving plates to become hard
Running Unevenly and inelastic. Clean the machine between the housing and heads.
 Check that grinding tools are properly positioned and not too worn.

 If “UPS” is shown, check the power source.

 If “FST” is shown, the emergency stop has been engaged. Press the
Error Code on Display “Reset” button to reactivate the machine.
 If “NST” is shown, turn the machine completely off and then back on.

For all other error codes your machine may display, contact CPS at 877.472.8200 or your
certified service technician.

Repairs

All repairs for CPS machines must be completed by a CPS authorized service technician.
Contact CPS or your retailer to locate certified service centers. Repairs must be completed by
trained specialists that have been authorized by CPS to complete machine repairs. Failure to
use a certified service technician may result in a voided machine warranty.
8.3 Replacement Parts

Replacement parts are available for routine maintenance on your machine.

Part #
APMF0254 Lower Belt (Pulley Box) for G-320D

GPPT0392 Flex Head Assembly

GPPT0077 Dust Skirt for G320D

APMF1239 Filter Kit

MTMC0047 Safe Fill Propane Tank

APMF1851K Flex Head Rebuild Kit (1 per head)

APMF1534 Upper Belt (From Engine to Center Pulley)

9.0 ACCESSORIES

The G-320D Propane machine is ideal for use with CPS products and accessories. Below are
some of CPS’ most popular items for use with the G-320D Propane machine.

9.1 Plates

There are several plates by CPS that fit the G-320D Propane machines.

Quick Change Plate Recessed Cup Resin Thick RD Driver Plate Metal Bond Plate
Plate
GPPT0601 MTPT0138K MTPT0130K APMF1477

9.2 Tooling

There are many applicable tools for the G-320D Propane. From tools perfect for surface prep to
polishing resins, CPS has you covered. Visit www.go2cps.com/tooling.html for more.
10.0 MAINTENANCE INDEX

In this section, you will find instructions for the most common routine maintenance procedures.
For any other issues or maintenance your machine requires, call CPS or your retailer to find a
certified service technician in your area. Please see the Maintenace Checklist below for more
information on when to do maintenance.
10.1 Rebuilding Flex Heads
10.2 Oil Changes
10.3 Changing the Oil Filter
10.4 Air Filter Service
10.5 Greasing The Ring Gear
10.6 Adjusting The Regulator
10.7 Changing The Spark Plugs