Scribd
Upload
235 views3 pages

Float Area Method

The document describes using the float-area method to estimate stream discharge when a current meter is unavailable, involving measuring the travel time of a floating object over a set distance to calculate velocity, taking cross-sectional measurements of width and depth to calculate area, and using these values in the equation of discharge being equal to velocity multiplied by area. Proper site selection and measurement techniques are outlined to perform this approximation method acceptably for hydrologic comparisons.

Uploaded by

Trisha Veronica Candelaria AVENGOZA
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
235 views3 pages

Float Area Method

The document describes using the float-area method to estimate stream discharge when a current meter is unavailable, involving measuring the travel time of a floating object over a set distance to calculate velocity, taking cross-sectional measurements of width and depth to calculate area, and using these values in the equation of discharge being equal to velocity multiplied by area. Proper site selection and measurement techniques are outlined to perform this approximation method acceptably for hydrologic comparisons.

Uploaded by

Trisha Veronica Candelaria AVENGOZA
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Stream Discharge using the Float-Area Method

The best approach for determining instantaneous stream or ditch flow is to use a current meter
(i.e. Flowtracker, Marsh-McBirney, Price AA) in conjunction with the standard USGS discharge
measurement methodology (http://pubs.usgs.gov/wsp/wsp2175/pdf/WSP2175_vol1a.pdf)
or a properly placed standard weir or flume. In the absence of these two approaches, the float-
area method may be used as an approximation of flow. Due to the inherent inaccuracies of this
methodology, the field method described below should be followed closely. This method, when
performed correctly, may qualify as a professionally documented hydrologic method for
comparison to estimation techniques used for physical surface water availability determinations
(ARM 36.12.1702(6)). Questions regarding this methodology may be directed towards Mike
Roberts or Dave Amman of Montana DNRC’s Water Management Bureau.

Float-Area Method
The amount of water passing a point on the stream channel during a given time is a function of
velocity and cross-sectional area of the flowing water.

Q = AV

where Q is stream discharge (volume/time), A is cross-sectional area, and V is flow velocity

You need:

 tape measure
 watch or stop-watch
 rod, yard or meter stick to measure depth
 buoyant objects such as a weighted block of wood or oranges (objects that float immersed
at the water surface)
 stakes for anchoring tape measure to stream banks
 waders

Site Selection:
 straight section of stream
 uniform in grade
 minimum surface agitation

Float method – This method measures surface velocity. Mean velocity is obtained using a
correction factor. The basic idea is to measure the time that it takes the object to float a specified
distance downstream.

Velocity

V = travel distance/ travel time

Because surface velocities are typically higher than mean or average velocities
V mean = k Vsurface where k is a coefficient that generally ranges from 0.66 to 0.75,
depending on channel depth.

 Choose a suitable straight reach with minimum


turbulence (ideally at least 3 channel widths
long).

 Mark the start and end point of your reach.

 If possible, travel time should exceed 20 seconds.

 Drop your object into the stream upstream of your


upstream marker.

 Start the watch when the object crosses the upstream marker and stop the watch when
it crosses the downstream marker.

 You should repeat the measurement at least 3 times and use the average in further
calculations.

Ex. Travel Distance = 50 feet 1st run = 34 sec.


2nd run = 32 sec.
3rd run = 28 sec.
k = 0.7 average run = 31.3 sec.

Velocity = (50 feet / 31.3 sec.) * 0.7 = 1.1 feet/sec.

Area

Area = average width * average depth

Measure stream’s width and depth across at least one cross section where it is safe to wade.
If possible, measure depth across the stream's width at the start and stop cross sections and
average the two but if only measuring one cross section choose the one downstream.

Use a marked rod, a yard or meter stick to measure the depth at regular intervals across the
stream. Five depth measurements are typical but more is better, especially in larger streams.
Average your cross-sectional areas (A): Using the average area and corrected velocity, you
can now compute discharge, Q.

See example below:

Float-Area Method
Example

Name: Roberts
Date/Time: 10/3/2015
Stream/Ditch: Unnamed Trib.

Discharge (Q) = Velocity *


Area
Upper Lower
Cross-Section Cross-Section
Area (width*average depth) width (ft) = 11.2 10.3
depth (ft) = 0.3 0.25
depth (ft) = 0.5 0.5
depth (ft) = 0.6 0.6
depth (ft) = 0.4 0.6
depth (ft) = 0.2 0.3

Avg depth (ft) = 0.4 0.45


Area (W*D) = 4.48 4.64
Avg Area (sq. ft) = 4.56

Velocity = (travel distance/travel time)*roughness coeff.

Travel Time Travel Velocity


(sec) Distance (ft) (ft/sec)
Run #1 32 50 1.6
Run #2 28 50 1.8
Run #3 34 50 1.5
Avg. Time (sec) = 31.3 50.0
V (avg) = 1.6
Roughness Coefficient
k= 0.66
Velocity (ft/s)= 1.06

Q (Discharge) Velocity * Area 4.8 cfs

You might also like