Gas Turbine

Download as docx, pdf, or txt
Download as docx, pdf, or txt
You are on page 1of 7

Guideline No.

: B-02(201510)

B-02THERMAL OIL HEATERS


Issued date: October 20,2015
©China Classification Society
Foreword:
This Guide is a part of CCS Rules, which contains technical requirements, inspection and testing criteria
related to classification and statutory survey of marine products.
This Guide is published and updated by CCS and can be found through http://www.ccs.org.cn. Comments
or suggestions can be sent by email to ps@ccs.org.cn.
Historical versions and release date :
Main changes and effective date:B-02(201510) THERMAL OIL HEATERS
3/8
CONTENTS
1 Application .................................................................................................................................. 4
2 Normative references .................................................................................................................. 4
3 Terms and definitions .................................................................................................................. 4
4 Plans and documents ................................................................................................................... 4
5 Materials and components .......................................................................................................... 5
6 Evaluation of welding procedures ............................................................................................... 5
7 Design and technical requirements ............................................................................................. 5
8 Strength requirements ................................................................................................................. 6
9 Type test ...................................................................................................................................... 6
10 Unit/batch inspection ................................................................................................................... 7 B-
02(201510) THERMAL OIL HEATERS
4/8
THERMAL OIL HEATERS
1Application
1.1This Guidelineapplies to works approval and inspection of oil-fired (light diesel oil, heavy diesel oil,
etc.) or exhaust–fired marine thermaloil heaters.
2Normative references
2.1CCS Rules for Classification of Sea-goingSteel Ships;
2.2CCS Rules for Materials and Welding.
3Terms and definitions
3.1Relevant definitionsspecified in CCS Rules for Classification of Sea-going Steel Shipsare applicableto
this Guideline.
3.2Marine thermal oil heater is a marine thermal fluid heater having a working temperaturenot more than
350℃, with organic heat transfer oil as working medium, and forced circulation by thermal oil pump.
Generally, it consists of the body of thermal oil heater, thermal oil collecting tank and thermal oil
expansion tank.
4Plans and documents
4.1The following plans and documents are to be submitted to CCSfor approval when applyingfor approval:
(1) Main performance specifications (including rated heating capacity, design pressure, maximum working
pressure, volume of circulating oil, uptake temperature, thermal efficiency, etc.);
(2) List of physical and chemical properties of materials of pressure parts material;
(3) General assembly;
(4) Body construction (including details of welded connections, attachments and supports);
(5) Drawings of main components such as coils, headers, thermal oil expansion tank, and thermal oil
collecting tank;B-02(201510) THERMAL OIL HEATERS
5/8
(6)Arrangement of mountings andfittings;
(7) Strength calculations;
(8) Diameter calculations for safety valves;
(9) Electrical control system (if necessary);
(10) type test programme.
4.2The following plans and documents are to be submitted to CCS for informationwhen applyingfor
approval:
(1) Standards applicable to products;
(2) Product instructions, product nameplates and manufacturer’s quality certificate (specimen).
4.3In addition to plans and documentsspecified in 4.1 and 4.2, the applicant is to submit other plans and
documents necessary for approval accordingto the relevant requirements in Chapter3, PART ONE of CCS
Rules for Classification of Sea-going Steel Ships.
5Materials and components
Materials and components are to comply with relevant requirements of CCS Rules
6Evaluation of welding procedures
6.1Prior to welding, the manufacturer is to formulate detailed welding procedure specifications for
approval by CCS, according to the relevant requirements of CCS Rules for Materials and Welding and the
characteristics (position, type and size) of material, construction and welding joints of pressure parts of
thermal oil heaters.
6.2The welding, weld examination and post-welding heat treatment of all pressure parts of thermal oil
heaters are to comply with the relevant requirements of CCS Rules for Materials and Welding.
7Design and technical requirements
7.1The design and technicalrequirements for the products are to comply with the relevant
requirementsinSection 8, Guideline4 and in Chapter6, PART THREE of CCS Rules for Classification of
Sea-going Steel Ships.B-02(201510) THERMAL OIL HEATERS
6/8
8Strength requirements
8.1The strength calculation and tests areto comply with the relevant requirements inChapter6, PART
THREE of CCS Rules for Classification of Sea-going Steel Ships.
9Type test
9.1Selection of typical samples
Samples are to be selected according to design pressure and heating area. Products representing the
manufacturer’s production capacity and manufacturinglevel are to be selected as samples, representing or
covering the scope of products for which approval is sought.
9.2Type test is to include the following items:
(1) material inspection;
(2) visual examination of welds;
(3) non-destructive testing of welds;
(4) coil inspection;
(5) inspection of expansion tank and collecting tank;
(6) hydraulic test.
9.3Type test is to comply with the following requirements:
9.3.1Materialinspection is to be carried out according to methods and requirements in Chapter1 ~ 4, PART
ONE of CCS Rules for Materials and Welding.
9.3.2Visual examination of welds: Close-up inspection of the surface of welds. The welding of pressure
parts is to comply with the relevant requirementsof CCS Rules for Materials and Welding. The surface of
welds is to be well formed, the edges of welds are to have smooth transitions to the base metal and the
width of welds is to be uniform.
9.3.3Non-destructive testing of welds is tobe carried out according to requirements as specified in Section
3, Chapter9, PART THREE of CCS Rules for Materials and Welding.
9.3.4Coil inspection:
⑴excessively large overlaps are not to be formed in the internal surfaces of butt joints after welding, and
the internal diameter at joints is to comply with requirements of ball-passingtest;
⑵the buttwelds are to be subjected to radiographictesting according to 9.3 (3);
⑶finished coils areto besubjected to hydraulic test to apressure twice the design pressure B-02(201510)
THERMAL OIL HEATERS
7/8
and no leakage is allowed;
⑷finished coils areto besubjected toball-passing test. For coil tubes, of which the welded portions are to be
bent to a radius less than 600 mm, the ball-passing diameter is 90% that of butt-welded straight tubes.
9.3.5Inspection of expansion tank and collecting tank:
⑴welded tube holes of tube joints are to be clear of welds so far as practicable;
⑵the longitudinal inclination and transverse inclination of tube joints are to be not more than 1.5 mm;
⑶the flange face inclination is to be not more than 2 mm;
⑷water filling test is to be carried out for finished expansion tank and collecting tank andno leakage is
allowed.
9.3.6Hydraulic test:
⑴after the single-pass tubes are formed, the pressure parts are to be subjected to hydraulic test to a
pressure twice the design pressure;
⑵after assembly, the tubes are to be subjected to overall hydraulic test to a pressure 1.5 times the design
pressure;
⑶water filling test is to be carried out for finished thermal oil expansion tank and collecting tank;
⑷hydraulic test and water filling test are deemed satisfactory where:
① no leakage is found in metal walls and welds of pressure parts; and

②no residual deformation is visible after completion of hydraulic test.


10Unit/batch inspection
10.1Unit/batch inspection for issuing marine products certificatesis to be carried out after CCS works
approval.
10.2Unit/batch inspection is to include the following items:
(1) The inspections are to be carried out according to approved inspection plan, including at least visual
examination of welds, non-destructive testing of welds, coil inspection, inspection of
expansiontank/collecting tank and hydraulic test.B-02(201510) THERMAL OIL HEATERS
8/8

(2) The manufacturer is to submit to CCS the documentation as specified in 5.1 and 5.2 of this Guideline.

You might also like