Having problem with Canon IP1300, IP1700, IP1200, IP1880, IP1980.

Sign that looked to be

only led blinking. Following some solutions problem of printer that marked with led blinking.
3x Orange 1x green
Problem : any problem with printer mechanics
Solution: If you don’t have knowledge about printer mechanic, will better if bring the printer to
Canon service center.
4x orange 1x green
Problem printer absorber full
Solution: Reset the printer using generaltools or software resetter. If not work using reset
manual. Each printers having different set of manual reset
5x orange 1x green
Problem: Black or Color cartridge trouble.
Note: problem is usually caused many matters, for example chips error, conector is dirty, etc.
7x orange 1x green
Problem: Black or Color cartridge trouble.
Note: problem is usually caused many matters, for example chips error, conector is dirty, etc.
8x orange 1x green
Problem printer absorber full (Waste Ink Pad Full)
Solution: Reset the printer using generaltools or software resetter. If not work using reset
manual. Each printers having different set of manual reset

Read more: http://tricks-collections.com/led-error-code-for-canon-ip1300-ip1700-ip1200-

ip1880%C2%A0ip1980/#ixzz0YJYmOu1h
CANON 140
1. Start with printer off
2. Press and hold resume Button (triangle in the circle) and click “Power”
button. green led should be on
3. While holding the Power button, release the Resume Button.
4. Without releasing the Power Button, click “Resume” button for two times and
release Both Buttons.
5. Click “Resume” for four times then soon click “Power” button, to confirm the
selected action (reset counter absorber).
6. Turn off the printer and turn on again

CANON MX318
Waste Ink Counter Reset.
(1) Turn off the printer.
(2) Press and hold the RESUME button, then press and hold the POWER button.
(3) Release the RESUME button, Next press and release the RESUME button
two(2) more times in
succession. Note: you are still holding the POWER button). The printer's carriage
will "reset"
or move momentarily. If the above was properly performed the printer will enter
the
"Service Mode".
(4) Press the RESUME button 4 times, this will select the clear waste ink counter
function. The lamp
will alternate (change) color with each key press.
1. Service/Factory test printout, including ink sensor check.
2. EEPROM - Info printout.
3. EEPROM - Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point - However it is best
leave them unaltered - You have been warned!)
After selecting the desired mode (eg 4), press the POWER button to "set" the
change, and return to the top of the function selection menu. Press the POWER
button again to restart the printer.
I get from forum but still untried, just sharing for the things requiring reset procedure for Canon
Pixma MP145 to reset counter in the Canon Pixma mp145. Following is the procedure to reset
waste ink counter Canon Pixma MP145 :
 Connected Printer to a Power source, Turn off the printer if printer on
 With the Printer power off, press the Power button while press and hold Stop/Reset
button.
 When the Power led is light, press Stop/Reset button two times while pressing and
holding the Power button.
 When releasing the Power button and the Stop/Reset button (regardless of order), the
printer will move into a service mode. (Waiting for menu selection)
 When the on/off lights in green, press the Stop/Reset button four times to reset wase ink
counter. For other specified number pressed function listed in the table below. (Each time
the Stop/Reset button is pressed, the LED lights alternately in orange and green, starting
with orange).
 Unplug cable power from a power source.

Resetter Canon iP1000, Canon iP1200, Canon iP1300, Canon iP1500, Canon iP1600, Canon
1700,Canon iP2200, Canon iP3000, Canon iP4200, Canon iP5200. this reset methode has
been tested.
Canon PIXMA iP1000, iP1500 Waste Ink Counter Reset
Step 1: Manual for Service mode
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.
step 2 : Using Software Resetter for Permanant
1. Reconnect the printer cable.
 2. Download
o General Tools software Resetter for canon Pixma iP 1500

o General Tools software Resetter for Canon PIXMA iP1000 Printers

3. Run the Software Resetter and select (USB PORT)

4. Choose SET DESTINATION 1 And it should be reset.
Remark “After service mode Pls use software for permanent reset”
Canon Pixma iP1200, iP1600, iP2200 Resetter
1. Download software for Canon iP1200, iP1600, 2200 Printers.DOWNLOAD Service Tool
Software for Canon Pixma Printer iP1200, iP1600, iP2200
2. Unzip downloaded file by WinZip, 7Zip, Izarc, etc
3. Run GeneralTool.exe
4. Select the connected USB port number from USB PORT
5. Click LOCK RELEASE, and select the applicable model name in SET DESTINATION
6. In CLEAR WASTE INK COUNTER, select MAIN or PLATEN. The selected waste ink
counter will be reset. MAIN resets the main waste ink counter, PLATEN resets the platen
waste ink counter.
If both the main and platen waste ink absorbers are replaced, reset both the main and platen
waste ink counters.
Resetter canon iP 1700 and iP1300
Methode 1 : Reset Hardware
1. Turn off Canon Pixma iP1700, iP1300 Printers
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the Canon Pixma iP1700, iP1300 Printers should turn off, if
not, press the Power button once more.
8. Your Canon Pixma iP1700, iP1300 Printers should respond as normal
Methode 2 : Using software resetter
1. Download Software Resetter for Canon Printers iP1300 dan iP1700 Software Resetter for
Canon Pixma iP1300, iP1700
 2. Ekstrak/Unrar/Unzip the Software
3. run GeneralTool.exe
4. Select USB Port where the canon ip1300 or canon ip1700 installed.
5. CLick Lock Release button
6. Select EEPROM CLEAR
7. Click Test Pattern 1 button
8. Your Canon Pixma iP1700, iP1300 Printers should respond as normal.
Resetting Ink-Waste Overflow Counter Canon Pixma iP3000, iP4000, iP5000 Printers
1. With the printer plugged in and powered off, press and hold the Resume/Cancel button,
then press and hold the Power button. (DO NOT release the buttons. The LED light
should be green to indicate that a function is selectable.).
2. While holding the Power button, release the Resume/Cancel button. (DO NOT release the
Power button.).
3. While holding the Power button, press the Resume/Cancel button 2 times, and then
release both the Power and Resume/Cancel buttons. (Each time the Resume/Cancel
button is pressed, the LED lights alternately in orange and green, starting with orange.).
4. When the LED light is green, press the Resume/Cancel button 4 times. (Each time the
Resume/Cancel button is pressed, the LED lights alternately in orange and green, starting
with orange.).
5. Press the Power button. The LED lights in green, and the reset is performed. (When the
operation completes, the printer returns to the menu selection mode automatically.).
6. Press the power button to exit service mode.
Note: if you accidentally press the Resume/Cancel button more than 4 times in step 4 then just
press the Resume/Cancel button at least 10 times and the printer will be returned to step 4
automatically
Canon Pixma iP4200, iP5200, iP6000, iP8500 Reset Procedure
1. Turn off the Printers.
2. Hold Resume button click POWER.
3. Hold button RESUME, release POWER
4. Then press the button again twice RESUME.
5. Release all the buttons.
6. Indicator led in green and stay green.
7. Click the button 4 times RESUME, if you want to make another transaction. :
Read more: http://tricks-collections.com/resetter-printers-canon-pixma-ip1000-ip1200-ip1300-
ip1500-ip1600-1700-ip1880-ip2200-ip3000-ip4200-ip5200/#ixzz0Y94IeRw4

Alarm light on and u051 error mx310

Computer Devices

By Rylee Smith

You’ll need to reset your printer to clear the ink counters, after resetting it’ll not display the error
code again. Follow this procedure to reset the printer--

1. Power off the printer.

2. Holding the stop/reset button, press and hold power button also. Hold both buttons together for
5 secs.

3. Still holding the power button, release the stop/reset buton, then press the stop/reset button
twice.

4. Release power button (the screen should now say 'Service Mode').

5. Wait until the power button lights steady green, then press the stop/reset button three times
with a 3 sec space between each press. On the 3rd press the indicator should turn steady orange.

6. Press the power button once, (the orange light should go off).

7. Open the printer and remove both cartridges. Wait for 10 seconds. Replace the cartridges and
close printer. Wait for 30 seconds.

8. Press the power button, and wait until printer has shut down.

9. Press power button to power up. The printer will feed one piece of paper, then ask you to set
the language.

10. The page counter is now reset.

RESETTING HP CARTRIDGES
This tutorial is designed to help you who are experiencing problems reset HP cartridges. Usually
when the cartridge is refilled, then the estimated ink level on HP Tool Box will appear empty.
Well, that estimated full level again ink cartridge HP then you need to reset. Here's how: To reset
the printer cartridge HP [HP 21, 22, 27, 28, 56, 57, 58]...

1. Refill your HP cartridge ink use your favorite reffil.

2. Follow the diagram above, the electronic license plate cover signed in blue with translucent
insulation (be careful, do not close the other areas).

3. Enter the cartridge into the printer. Printer will tell you there are problems in your cartridge.
Ignore this warning. Printer will print the alignment page.

4. Take the cartridge from the printer. remove the insulation. Close the electronic plate marked
with red color.

Note: blue and red color illustration only. You do not give color to your HP cartridge.

(Not until the closing pin as above. Remember the lid pin red and blue only)
5. Follow the steps no. 3.

6. Remove the cartridge from the printer for the last time. Shut off the isolation of the electronic
plat. Place the cartridge in the printer again. Printer should print the alignment page and the ink
level indicator on the toolbox should read full.

Closed pin, pin not to shut.

If the tape is off the then both still appear "Cartridge (s) incorrectly installed" try clean pins are
in the picture slowly Cartridge use eraser, hpqste08.exe stop process from task manager
continues to run again HP Solution Center . If you can not also service center please contact the
nearest HP printers. Hope helps

Here are some basic EPSON printer errors for the EPSON 7600 & 9600 series.
LCD Panel Messages:
0002 CR pass count reaches the limit Perform Maintenance Mode 2
Perform Maintenance Mode 2 [CLEAR COUNTERS / CR MOTOR
0008 RTC backup battery is empty
Install the battery and perform Maintenance Mode 2
0020 The number of shots (per nozzle) reaches the limit
Perform Maintenance Mode 2 [CLEAR COUNTERS / CLEANER]
0040 Pump motor operation count reaches the limit
Perform Maintenance Mode 2[CLEAR COUNTERS / CLEANER]
0080 Date is not specified
Perform Maintenance Mode 2[CLEAR COUNTERS / CLEANER]
0100 RTC backup battery drops
(Wait for a while) *2“If the same message appears again, replace the RTC backup battery and
performMaintenance Mode 2 [CLEAR COUNTERS / RTC].”
0088 RTC backup battery is not installed
Install the battery and perform Maintenance Mode 2[CLEAR COUNTERS / CLEANER]
Posted by Kuyung at 12:28 AM 0 comments

Labels: EPSON 9600, ERROR CODE EPSON 7600

RESET ERROR CODE CANON MP145-MP150-MP160

E2-2 = No paper (ASF)

E3-3 = Paper jam

E4 = No ink

E5-5 = The ink cartridges are not installed or a non-supported ink cartridge
is installed, or the ink cartridges are not installed properly

E8 = Waste ink absorber full, or platen waste ink absorber full

E9 = The connected digital camera / video camera does not support Camera
Direct Printing

E14 = The Ink cartridges whose destination are wrong

E15 = Ink cartridge is not installed E16 - Ink remaining is unknown

E16 -E19 = Failed to scan head alignment sheet

E22 = Carriage error

E23 = Paper feed error

E24 = Purge unit error

E25 = ASF(cam) sensor error

E26 = Internal temperature rise error

E27 = Waste ink absorber full or platen waste ink absorber full

E28 = Ink cartridge temperature rise error -

E29 = EEPROM error

E33 = Paper feed position error

E35 15 = USB Host VBUD overcurrent error - USB

E37 17 = Abnormal motor driver error

E40 20 = Other hardware error

E42 22 = Scanner error