Motors: Single and Multiple Vane Pumps & Vane Motors

Download as pdf or txt
Download as pdf or txt
You are on page 1of 120

SINGLE AND MULTIPLE VANE PUMPS & VANE MOTORS

Introduction
General Information BH* & V*
General Information DT6*
5

Single Vane Pumps


BH*, V* and DT6* single vane pumps 2
11
2
Thru Drive Single Vane Pumps
V**T thru drive single vane pumps
49
2
Double Vane Pumps
BH*, V* and DT6* double vane pumps
57
2
Triple Vane Pumps
DT6* triple vane pumps
79

Special Pumps 2
Pumps with tank, flow regulating & pressure limiting valves.
Compact Power Pack & Pump
87
2
Motors
MD4C & MHP Motors
97
2
Instructions for Use and Repairs (V* Series)
Cartridge identification, change of rotation, guidelines for repairs
105
2
Instructions for Use and Repairs (DT61Series)
Cartridge identification, change of rotation, guidelines for repairs
115
2

1
2
HYDRAULIC VANE PUMPS
Versión Corel 1.0: 01-06-06

3
4
SINGLE AND MULTIPLE VANE PUMPS

BH*, V* & DT6 HYDRAULIC VANE PUMPS


INTRODUCTION

TDZ vane pumps are manufactured in a wide range of displacements, from 2 cc/r to 269 cc/rev.
for single pumps, 460 cc/rev. for double pumps and 560 cc/rev. for triple pumps. 2

INTRODUCTION
All TDZ pumps have a low power to weight ratio, high efficiency, low noise levels, optional inlet
and outlet port positions and ease of maintenance.

Ease of maintenance is achieved by the pump design, where the working components are
contained within a cartridge which can quickly and easily be replaced without disconnecting the
pump from the prime mover or moving it away from the pipe work. TDZ vane pumps are
hydraulically balanced, reducing wear and eliminating bearing loads from within the pump.

The option to rotate the outlet port 90 degrees in relation to the inlet port provides flexibility and
easy installation.

Depending on the application, there are three versions of the larger single, double and triple vane
pumps: low noise industrial models VS and BHS, mobile models VQ and BHQ and multi-
purpose models DT6 (275 bar).

Models VS, VQ and DT6 have UNC threads for the port flanges whilst models BHS, BHQ have
metric threads. On single pumps the outlet port is at the shaft end for models VS, VQ, DT6 on
models BHS and BHQ the outlet port is at the cover end.

5
SINGLE AND MULTIPLE VANE PUMPS

V* & BH* HYDRAULIC VANE PUMPS


INTRODUCTION

PUMP DRIVE
Direct coaxial drive is recommended via flexible coupling. For indirect drives imposing a radial load on the shaft,
consult TDZ HYDRAULICS S.A. or your nearest distributor for advice.

ROTATION
The direction of rotation can be reversed by turning the ring, rotor and vanes through 180 degrees.
Direction of rotation is viewed from the shaft end.

STARTING
TDZ vane pumps are self priming, however, if possible, fill the pump with oil before starting or bleed the outlet port
while the pump is running to remove any trapped air.

FILTRATION
For satisfactory service life, full flow filtration to provide fluid cleanliness conforming to ISO code 18/15 or better is
recommended.

HYDRAULIC FLUIDS
Use antiwear industrial hydraulic oils with a viscosity of 25-49 cST. Automotive crankcase oils SAE10-SAE20 may
also be used depending on the operating temperature.

The optimum operating temperature is 50 °C with a maximum of 70 °C. At higher temperatures service life is
decreased with degradation of the wearing parts and seals.

For fire resistance fluids, the "F3" version with special seals must be used at reduced pressures and speeds as
indicated below.

MAXIMUM SPEED RANGES


With antiwear fluids: 1800 to 2500 rpm (depending on model type. See performance chart).

With synthetic fluids, water glycols and water in oil emulsions, the maximum recommended speed is 1200 rpm. A
special version of the BHP2 pump is available for speeds up to 5000 rpm

Speeds shown are given as a guide only based on the correct fluid and correct suction characteristics as
recommended by our Technical Services department.

Long or restricted suction lines can cause cavitation, therefore the maximum running speed must be reduced.
Avoid using 90 degree elbows in suction lines, use swept bends where possible. Too viscous fluids will also cause
cavitation.

When using lower displacement pumps within a given pump frame size, speeds slightly higher than those shown in
the charts are acceptable.

For antiwear hydraulic fluids and water glycols, the inlet pressure must not exceed 0.2 bar vacuum, for synthetic
fluids and water in oil emulsions, the inlet pressure must not exceed 0.1 bar vacuum.

MINIMUM SPEED: 600 rpm

This data is for V*20, V*25,V* 35,V* 45, BH*4,BH* 6, BH*7, double and triple pumps. For other pumps see chart.

The intermittent pressures shown in the table can be maintained for 10% of the time, with a maximum duration of 6
seconds/minute.

6
SINGLE AND MULTIPLE VANE PUMPS

V* & BH* HYDRAULIC VANE PUMPS


INTRODUCTION

MAXIMUM CONSTANT PRESSURE


Anti-wear Hydraulic Oil: from 175 to 210 Bar
Synthetic Oil: from 175 to 210 Bar

INTRODUCTION
Water-Glycol emulsions: 160 Bar
Water-in-oil emulsions: 70 Bar

SOUND LEVEL
Single Pumps: : 2
VS25 and BHS4: 62 dB (A)
VS35 and BHS6: 65 dB (A)
VS45 and BHS7: 71 dB (A)

Double Pumps:
VS43: 68 dB (A)
VS63: 69 dB (A)
VS73: 71 dB (A)
VS64: 69 dB (A)
VS74: 71 dB (A)
VS76: 72 dB (A)

Sound levels measured with hydraulic oil at 140 Bar, 1500 rpm and a vacuum at pump inlet of 0,17 Bar.

ADMISSIBLE TORQUES FOR THE SHAFTS


All the shafts available for our single pumps and motors are sufficient for working at the maximum pressure specified for
each model.

However, in the case of double pumps and thru drive pumps, if both cartridges/pumps work simultaneously under pressure,
the sum of the torques absorbed for each of them may exceed the resistance of the shaft.

In practice, the absorbed torque for each cartridge/pump may be calculated with the formula:

PxV Where: T = Torque in Nm.


T= P = Working pressure in Bars.
59
V = Cubage in cm3/rev. or flow in lts/min at 1,000 R.P.M.

In order to choose the most appropriate type of shaft, calculate said torque sum under the most unfavourable working
conditions and compare them with the torque values admitted for each shaft as indicated in table 1.

Analogically, in the thru drive pumps, the absorbed torque for the second pump will be calculated under the most
unfavourable conditions, and it must be checked that it does not exceed the torque values admissible as indicated in table
2 for each connection.

Table 1 Table 2

Pump Max.Torque Rear Max. Torque


Type Shaft nº
Nm Flange
(Conection) Nm
V*42 1 313 A 130
V*43 11 313
V*4T 86 392 B 315

V*63 1 392 C 440 (V*6TC)


V*64 11 568 700 (V*7TC)
V*6T 86 588

V*73
V*74
1 588
V*76
11 803
V*7T
86 803

7
SINGLE AND MULTIPLE VANE PUMPS

DT6 HYDRAULIC VANE PUMPS


INTRODUCTION

DT series vane pumps are fixed displacement and high efficiency pumps. Designed under SAE J744c 2 bolt standards,
2 triple pumps), the complete range includes single, double and triple units with wide possibilities of flow
(excluding T6EDC
combinations, porting configurations, possibilities of use of fluids other than petroleum-based oil and a vast number of different
shafts.

The DT series is a hydraulically-balanced design. Quality and composition of materials have been checked and tested over millions
of cycles on our experimental test benches. This fact, together with a rigid bearing and a high resistance to particle contamination
thanks to the double lip vane, makes DT series pumps long -life hydraulic units.

Within 3 different cartridge kit sizes, flows available range from 3 to 31 GPM in C size, 14 to 61 GPM in D size and 42 to 85 GPM in D
size. As in our earlier BH* and V* vane pump series, cartridge kit design allows easy service when replacement or conversion is
needed, reducing the operation to just a few minutes. Cartridge kit design also offer possibilities of quick change of rotation by
changing the position of cam ring .

Four different combinations of porting positions are possible in single pumps. In double pumps 32 combinations are possible and
128 for triple pumps.

The high pressure capability of 275 bar in the DT6 series reduces installation costs and provides long life at reduced pressure.
The high mechanical and volumetric efficiency reduces heat generation and energy consumption. Lower noise levels than most
of hydraulic pump designs suppose an advantage and safety for machine operators.

TDZ Hydraulics DT series vane pumps are unidirectional but they have been designed for an easy change of rotation.
Instructions for change of rotation are included in this catalogue (Instructions for Use and Repair).

RECOMMENDED FLUIDS

Operating characteristics showed in this catalogue have been calculated considering the use of Antiwear petroleum base fluids.

Non Antiwear Petroleum Base Fluids, Synthetic Fluids, Water In Oil Emulsions or Water Glycols are also acceptable. In these cases,
speed and pressure limits will be supplied directly by TDZ Hydraulics or your nearest distributor.

VISCOSITY

Optimum viscosity for maximum life is between 30 and 40 cSt.


Maximum viscosity is 2000 cSt at very low speed and pressure and 110 cSt at full speed and pressure.
Minimum viscosity is 10 cSt, (18 cSt for fluids other than Antiwear Petroleum Base fluids).

FLUID CONTAMINATION AND FILTRATION

Fluid must be clean during the entire working life of the pump in order to maintain a contamination level of ISO 18/14 or even better, if
possible.

Filters with 25 microns are adequate but will not guarantee total cleanliness levels. Suction strainers should be of an adequate size to
provide the recommended inlet pressure. For cold starts or fire-resistant fluids, oversize strainers must be used or omitted.

Higher levels of water than 0.10% in mineral oils or 0.05% in synthetic or biodegradable fluids are not acceptable. In these
cases, water should be drained off the circuit.

FLUID TEMPERATURES

Fluid viscosity should be selected depending on the normal operating temperature of the unit. Cold starts pump should operate at
low pressure and, if possible, low speeds until the fluid warms up to a convenient viscosity for full power application.

MINIMUM AND MAXIMUM SPEED

Minimum: 400 rpm.


Maximum: 2800 rpm in C series, 2500 rpm in D series and 2200 in E series.

Higher flows of C and D sizes also involves speed limitations, as indicated in the technical chart of this catalogue. Fluids other than
Antiwear Petroleum Base fluids will also involve a speed limit, depending on the choice, (consult TDZ or your nearest distributor).

8
SINGLE AND MULTIPLE VANE PUMPS

DT6 HYDRAULIC VANE PUMPS


INTRODUCTION

PRESSURE RATINGS

Maximum pressure in DT6 vane pumps is 275 bar intermittent for C series and 240 bar for D and E series. Nevertheless,
exceptions are indicated in this catalogue when fluids other than Antiwear Petroleum Base are used or in the case of use of

INTRODUCTION
high flows of C and D pump sizes.

Both continuous and intermittent pressures are indicated in this catalogue. The maximum period of intermittent pressure may
be considered acceptable when the average pressure time is less than or equal to the continuous recommended pressure, for
that particular model during a complete cycle of work.

MINIMUM INLET PRESSURE

Minimum allowable inlet pressure is 0.95 bar for 1,800 rpm or less, 1.10 bar between 1,800 and 2,300 rpm and 1.30 bar
when the speed is more than 2,300 rpm.

Multiply the above-mentioned values by 1.40 when fluids other than Antiwear Petroleum base fluids are used.

The difference between inlet pressure and atmospheric pressure should not exceed 0.2 bar to prevent aeration. Inlet
Pressure is considered with petroleum base fluids at viscosities of between 10 and 65 cSt.

9
2

10
SINGLE VANE PUMPS

SINGLE VANE PUMPS


BH*, V* and DT6 single vane pumps

2 11
BH* SINGLE VANE PUMPS

BH* SINGLE VANE PUMP ORDERING CODE

F3 BHQ 4 67 D 1 A 00
1 2 3 4 5 6 7 8

1 - "F3" means special seals for fire-resistant fluids. Omit if not required.

2 - Pump Type:

BHP = 10 vane pump, industrial and mobile use, BSP, NPT & SAE threads.
BHS = 12 vane pump, industrial use (very quiet), metric threads.
BHQ = 10 vane pump and bronze plates, mobile use, metric threads.

3 - Pump model: 1, 2 and 3 in BHP types; 4, 6 and 7 in BHS and BHQ types.

4 - Flow: BHP, BHS and BHQ in Litres per minute at 1000 rpm and 7 Bar.

5 - D = Right-hand direction of rotation (Clockwise).


Y = Left-hand direction of rotation.
(To check the direction of rotation view from the shaft end).

6 - Shaft type: See on each pump model.

7 - Oulet position, (viewed from shaft):


A: Outlet in line with inlet.
B: 90° on the right from inlet (Clockwise from inlet).
C: 180° from inlet.
D: 90° on the left from inlet (90° counterclockwise from inlet).

8- Special characteristics
Omit if not required.
Example: 02 : BSP
03 : UNF
04 : NPT

12
BH* SINGLE VANE PUMPS

BH* SINGLE VANE PUMP CHARACTERISTICS

2
TDZ DESIGN VANE PUMPS

FLOW SPEED PRESSURE Nominal CONNECTION WEIGHT


TYPE (rpm) (Bar) Power (Kgs.)

SINGLE VANE PUMPS


Lts.at Gal. At Reduction
(3) Inlet Outlet
1000 rpm 1200 rpm (2) Mín. Máx. Contin. Intermit.
2 0,6 0,18 0,5
3 0,9 0,18 0,7
BHP1 4,5 1,2 0,36 600 2500 150 175 1 (4) (4) 1
5,5 1,7 0,36 1,4
6,5 2 0,36 1,6

7 2,2 0,7 1,8


8 2,5 1,1 2
BHP2 10 3,2 1,1 600 2500 150 175 2,5 (4) (4) 3,6
12 3,8 1,1 3
(1) 15 4,7 1,1 3,7

6 2 0,9 1,9
16 5 1,7 4,3
18 6 2,8 5,3
25 8 4,5 6,9
BHP3 27 9 4,8 600 2500 150 175 7,6 (4) (4) 7,1
35 11 4,8 8,8
38 12 5,4 10,2
44 14 6,6 2000 11,9
50 16 7,8 1500 100 125 13,6

26 8 4,5 6,9
40 12 5,7 10,4
45 14 5,7 2500 11,6
BHS4 55 17 5,8 600 1800 175 210 13,8 Ø38 Ø26 14,5
60 19 5,8 (BHS) 14,6
BHQ4 67 21 6 16,8
80 24 6,2 20,3
88* 27* 6,5 1500 125 150 22,4
66 21 8,6 16,8
81 25 9 2400 20,3
BHS6 97 30 10 1800 24,3 Ø60
600 175 210 Ø32 26,3
BHQ6 112 35 11,4 (BHS) 27,4
121 38 11,4 29,3
142 45 13,1 1500 125 150 33,3

138 42 15 32,3
148 47 15,7 36,3
162 50 14,3 2200 37,9
BHS7 155 175 43,2 38,3
180 57 17,9 600 1800 Ø75 Ø38
BHQ7 193 60 18,6 (BHS) 46,1
214 67 22 51,2
240 75 26 57,4

* 27 gallons (88 lts.) cartridge not mounted in BHQ4 vane pump model.

(1) There is a version of this pump with built-in flow regulating and pressure limiter valves, ref. B2V. If a built-in tank with filter is
required, the ref. Is B2VC (1.5 ltrs. tank) or B2VA (1 litre tank).

(2) Delivery flow reduction in Ltrs./min. at 100 Bar. 22 cST of oil viscosity at operating temperature. To calculate the
approximate delivery flow at a given pressure and speed, use the following formula with flow reduction and theoretical flow values
shown in the chart. Flow reduction values are independent of shaft speed.

Approx. output flow (Ltrs./min.) = Theoretical flow x R.P.M


1000
- Reduction x Pressure (Bar)
1000
(3) Nominal power in H.P. at 100 Bar and 1000 RPM (to convert into Kw multiply by 0.735).
To obtain the real input power at different pressure and revolutions, use the formula as follows:

Real input power = Input power x R.P.M x Pressure (Bar)


1000 1000
(4) See options on dimension pages.

13
BH* SINGLE VANE PUMPS

SINGLE VANE PUMP TYPE BHP-1


FLOW SPEED (rpm) PRES (BAR) CONNECTION WEIGHT

Lts at 1000 rpm 2 3 4,5 5,5 6,5 Mín. Máx. Contin. Intermit. Inlet Outlet (Kgs.)
Gal at 1200 rpm 0,6 0,9 1,2 1,7 2 600 2500 175 210 Ø38 Ø26 14,5

DIMENSIONS IN MILLIMETRES 1" = 25.4 millimetres


Nº1 Shaft

See shaft types and measures


Nº2 Shaft
See chart
See chart

Conicalness 1:8

Inlet Outlet

BHP1 PUMP AND FRAME SET TO


CONNECT TO ELECTRIC MOTOR

Frame
REF. GO 01007

14
BH* SINGLE VANE PUMPS

SINGLE VANE PUMP TYPE BHP-1

FLOW AND INPUT POWER DIAGRAMS

SINGLE VANE PUMPS

15
BH* SINGLE VANE PUMPS

SINGLE VANE PUMP TYPE BHP-2

FLOW SPEED (rpm) PRES (BAR) CONNECTION WEIGHT


Inlet Outlet (Kgs.)
Lts at 1000 rpm 7 8 10 12 15 Mín. Máx. Contin. Intermit.
Gal at 1200 rpm 2,2 2,5 3,2 3,8 4,7 600 2500* 150 175 3/4" BSP 1/2" BSP 3,6
* For further details see general chart
DIMENSIONS IN MILLIMETRES 1" = 25.4 millimetres

97
61 20
2,2 Kp.m.

53
Ø10,2

40

5 93

112
11
See chart (Inlet)
See chart (Outlet)
Num. Inlet Outlet
02 3/4" BSP 1/2" BSP

80 ø50 f7

Nº3 Shaft
Nº1 Shaft Nº2 Shaft

Diametral pitch: 16/32


Tooth number: 9

Enquire about other types of shafts

16
BH* SINGLE VANE PUMPS

SINGLE VANE PUMP TYPE BHP-2

FLOW AND INPUT POWER DIAGRAMS

SINGLE VANE PUMPS


l/min US Gal/min

40 10,6

35 9,2

30 15 7,9
15

25 6,6
12
12

20
10
5,3
10

15 8 8 3,9
7 7

10 5 5
2,6

5 1,3

500 1000 1500 2000 2500 R.P.M.

0 BAR 175 BAR

HP Kw
16 12,0

14 15
10,5

12 9,0
12

10 7,5
10
15

8 6,0
8
12
7

6 10
4,5
5 8
7
4 3,0
5

2 1,5

500 1000 1500 2000 2500 R.P.M.

100 BAR 175 BAR

17
BH* SINGLE VANE PUMPS

SINGLE VANE PUMP TYPE BHP-3


FLOW SPEED (rpm) PRES (BAR) CONNECTION WEIGHT
2 Min. Max. Contin. Intermit. Inlet Outlet (Kgs.)
Lts at 1000 rpm 6 16 18 25 27 35 38 44 50
Gal at 1200 rpm 2 5 6 8 9 11 12 14 16 600 2500* 150 175 1" BSP 3/4" BSP 7,1

* For further details see general chart See chart below for
additional connections
DIMENSIONS IN MILLIMETRES 1" = 25.4 millimetres

See chart See chart

Num. Inlet Outlet

01 1" BSP 3/4" BSP

02 1" 1/4 BSP 3/4" BSP

03 1" 5/8 UNF 1" 1/16 UNF

04 1" 1/4 NPT 3/4" NPT

Standard version.(SAE flange)

Parallel shaft Version for direct mounting in


Nº 1 Nº 6 Power Take-Off (ISO flange)
A 45 62.5
Splined shaft
B 2 1 Nº 2 Nº 4 Nº 5

C Ø25 Ø25 A 47 30 24,5


Shaft E
D 30 41 B 1 1 1 Diametral pitch 16/32
Nº 2 Teeth:13
E 5 4,75 C Ø25 Ø25 Ø25
DIN 5482 B18x15
Nº 4 Teeth:10
F Ø19 Ø19 D 15 4 3,5
Nº 5 Diametral pitch 16/32
G 21,1 21,1 F Ø21,80 Ø17,1 Ø15,82 Teeth:9

18
BH* SINGLE VANE PUMPS

SINGLE VANE PUMP TYPE BHP-3

2
FLOW AND INPUT POWER DIAGRAMS

SINGLE VANE PUMPS


l/min US Gal/min

120 31,7

105 27,7

90 23,8
43
43
75 37 19,8
37 34
34
60 15,9
28
28
24
45 24 11,9
19
19
30 7,9

15 3,9

500 1000 1500 2000 2500 R.P.M.

0 BAR 175 BAR

HP Kw
40 29,8
43

35 26,1
37

34
30 22,4

25 28 43
18,6
24 37
20 34 14,9
19
28
15 11,2
24

19
10 7,4

5 3,7

500 1000 1500 2000 2500 R.P.M.

100 BAR 175 BAR

19
BH* SINGLE VANE PUMPS

SINGLE VANE PUMP TYPE BHS-4 & BHQ-4


FLOW SPEED (rpm) PRES (BAR) CONNECTION WEIGHT
2 Mín. Máx. Contin. Intermit. Inlet Outlet (Kgs.)
Lts at 1000 rpm 26 39 44 54 60 66 80* 85*
Gal at 1200 rpm 8 12 14 17 19 21 24* 27* 600 2500* 175 210* Ø38 Ø26 14,5

* For further details see general chart


DIMENSIONS IN MILLIMETRES 1" = 25.4 millimetres

See shaft types and measures

Nº2 Shaft
Nº1 Shaft

Diametral pitch: 16/32

Tooth number:13

Enquire about other types of shafts

20
BH* SINGLE VANE PUMPS

SINGLE VANE PUMP TYPE BHS-4 & BHQ-4

2
FLOW AND INPUT POWER DIAGRAMS

SINGLE VANE PUMPS


l/min US Gal/min

160 42,3

140 37,0

120 66 66
31,7
60 60

100 54 54 26,4

80 44 44 21,1
39
39

60 15,9

40 10,6

20 5,3

500 1000 1500 2000 2500 R.P.M.

0 BAR 210 BAR

HP Kw
80 59,7
66

70 52,2
60
54
60 44,7

44
50 37,3
39

40 66 29,8
60
54
30 22,4
44
39

20 14,9

10 7,5

500 1000 1500 2000 2500 R.P.M.

100 BAR 210 BAR

21
BH* SINGLE VANE PUMPS

SINGLE VANE PUMP TYPE BHS-6 & BHQ-6

FLOW SPEED (rpm) PRES (BAR) CONNECTION WEIGHT


2 (Kgs.)
Lts at 1000 rpm 66 81 97 112 121 142* Mín. Máx. Contin. Intermit. Inlet Outlet
Gal at 1200 rpm 21 25 30 35 38 45* 600 2400* 175 210* Ø60 Ø32 26,3

* For further details see general chart


DIMENSIONS IN MILLIMETRES 1" = 25.4 millimetres

See shaft types and measures

Nº1 Shaft Nº2 Shaft

Diametral pitch: 12/24

Tooth number:14

Enquire about other types of shafts

22
BH* SINGLE VANE PUMPS

SINGLE VANE PUMP TYPE BHS-6 & BHQ-6

2
FLOW AND INPUT POWER DIAGRAMS

SINGLE VANE PUMPS


l/min US Gal/min

320 84,5

280 74,0

240 63,4
118 118
112
200 112
52,8
94 94
160 42,3
78 78

120 66 66 31,7

80 21,1

40 10,6

500 1000 1500 2000 2500 R.P.M.

0 BAR 210 BAR

HP Kw

160 119,3

140 104,4

120 89,5
118
112
100 74,6
94

80 59,6
78
118
66 112
60 94
44,7
78

40 66 29,8

20 14,9

500 1000 1500 2000 2500 R.P.M.

100 BAR 175 BAR

23
BH* SINGLE VANE PUMPS

SINGLE VANE PUMP TYPE BHS-7 & BHQ-7


FLOW SPEED (rpm) PRES (BAR) CONNECTION WEIGHT
2 Mín. Máx. Contin. Intermit. Inlet Outlet (Kgs.)
Lts at 1000 rpm 138 148 162 180 193 214 240
Gal at 1200 rpm 42 47 50 57 60 67 75 600 2200* 155 175 Ø75 Ø38 38,3

* For further details see general chart


DIMENSIONS IN MILLIMETRES 1" = 25.4 millimetres

See shaft types and measures

Nº1 Shaft Nº2 Shaft

Diametral pitch: 12/24:

Tooth number:14

Enquire about other types of shafts

24
BH* SINGLE VANE PUMPS

SINGLE VANE PUMP TYPE BHS-7 & BHQ-7

2
FLOW AND INPUT POWER DIAGRAMS

SINGLE VANE PUMPS


l/min US Gal/min

560 147,9

490 129,4

420 111,0

350 195
195
92,5
180
180

280 160 160


74,0
148 148
135 135

210 55,5

140 37,0

70 18,5

500 1000 1500 2000 2500 R.P.M.

0 BAR 175 BAR

HP Kw
200 149,1

175 195 130,5


180

150 111,8
160
148

125 135
93,2

100 195
74,6
180
160
75 148 55,9
135

50 37,3

25 18,6

500 1000 1500 2000 2500 R.P.M.

100 BAR 175 BAR

25
V* SINGLE VANE PUMPS

V* SINGLE VANE PUMP ORDERING CODE

F3 VS 25 67 D 1 A 00
1 2 3 4 5 6 7 8

1 - "F3" means special seals for fire-resistant fluids. Omit if not required.

2 - Pump Type:

VK = 10 vane pump, mobile and industrial use, UNC threads.


VS = 12 vane pump, industrial use (very quiet), UNC threads.
VQ = 10 vane pump and bronze plates, mobile use, UNC threads
.
3 - Pump model: VC10, VC20; 20, 25, 35 and 45 in VS and VQ types.

4 - Flow: VC, VS and VQ in US Gallons per minute at 1200 rpm and 7 Bar.

5 - D = Right-hand direction of rotation (Clockwise).


Y = Left-hand direction of rotation.
(To check the direction of rotation view from the shaft end).

6 - Shaft type: See on each pump model.

7 - Oulet position, (viewed from shaft):


A: Outlet in line with inlet.
B: 90° on the right from inlet (Clockwise from inlet).
C: 180° from inlet.
D: 90° on the left from inlet (90° counterclockwise from inlet).

8- Special characteristic
Omit if not required
Example: 02 : BSP
03 : UNF
04 : NPT

26
V* SINGLE VANE PUMPS

SINGLE VANE PUMP CHARACTERISTICS

VICKERS DESIGN VANE PUMPS 2


FLOW SPEED PRESSURE Nominal CONNECTION WEIGHT
TYPE (rpm) (Bar) Power (Kgs.)
Lts.at Gal.at Reduction
(3)
1000 rpm 1200 rpm (2) Mín. Máx. Contin. Intermit. Inlet Outlet

SINGLE VANE PUMPS


3 1 0,8 4800 0,7
6 2 0,9 4500 1,4
9 3 1,2 4000 155 2,1
VC10 13 4 1,6 600 3400 180 2,7 (4) (4) 4,5
16 5 1,7 3200 3,2
19 6 1,8 3000 3,7
22 7 1,9 2800 140 4,2

19 6 2,8 3400 3,9


22 7 4,2 3000 4,4
26 8 4,5 2800 155 180 5,1
VC20 29 9 4,8 600 2800 5,6 (4) (4) 7,3
(1) 36 11 4,8 2500 6,5
39 12 5,4 2400 7,5
42 13 6,0 2400 140 8,1

8 2 0,9 1,9
18 5 2,1 4
VK20 27 8 2,8 6,6
29 9 3,5 600 1800 175 210 6,9 Ø1½" Ø3/4" 12
VQ20 36 11 4,3 7,3
39 12 4,3 7,4
46 14 5,3 210 7,6

26 8 4,5 6,9
40 12 5,7 10,4
2500
45 14 5,7 11,6
1800 175 210 Ø1½" Ø1" 15
VS25 55 17 5,8 600
(VS)
13,8
60 19 5,8 14,6
VQ25 67 21 6 16,8
80 24 6,2 1500 125 150 20,3
88* 27 6,5 21,1
66 21 8,6 16,8
81 25 9 2400 20,3
VS35 97 30 10 600 1800 175 210 24,3 Ø2" Ø1¼" 23
112 35 11,4 (VS) 27,4
VQ35 121 11,4
38 29,3
142 45 13,1 1500 125 150 33,3
138 42 15 32,3
148 47 15,7 36,3
VS45 162 50 14,3 2200 37,9
180 57 17,9 600 1800 155 175 43,2 Ø3" Ø1½" 35,5
VQ45 193 60 18,6 (VS) 46,1
214 67 22 51,2
240 75 26 57,4

* 27 gallons (88 lts.) cartridge not mounted in BQ25/vane pump model.


(1) There is a version of this pump with built-in flow regulating and pressure limiter valves, ref. VC20F.

(2) Delivery flow reduction in Ltrs./min. at 100 Bar. 22 cST of oil viscosity at operating temperature. To calculate the approximate
delivery flow at a given pressure and speed, use the following formula with flow reduction and theoretical flow values shown in the chart.
Flow reduction values are independent of shaft speed.

Approx. output flow (Ltrs./min.) = Theoretical flow x R.P.M - Reduction x Pressure (Bar)
1000 1000
(3) Nominal power in H.P. at 100 Bar and 1000 RPM (to convert into Kw multiply by 0.735).
To obtain the real input power at different pressure and revolutions, use the formula as follows:

Real input power = Input power x R.P.M. x Pressure (Bar)


1000 100
(4) See options on dimension pages.

27
V* SINGLE VANE PUMPS

SINGLE VANE PUMP TYPE VC-10

2 FLOW SPEED (rpm) PRESSURE Nominal


Power
CONNECTION WEIGHT
Lts.at Gal.at Reduction (rpm) (Bar) (Kgs.)
(3)
1000 rpm 1200 rpm (2) Mín. Máx. Contin. Intermit. Inlet Outlet
3 1 0,8 4800 0,7
6 2 0,9 4500 1,4
9 3 1,2 4000 155 2,1 1" NPT 1/2" NPT
13 4 1,6 600 3400 180 2,7 4,5
1" BSP 1/2" BSP
16 5 1,7 3200 3,2
19 6 1,8 3000 3,7
22 7 1,9 2800 140 4,2
(2) & (3) see page 27.

See shaft types and measures

Dimension
Gallons

Num. Inlet Outlet Nº1 Shaft

02 1" BSP 1/2 BSP

04 1" NPT 1/2" NPT

Contact TDZ or your nearest


distributor for other shaft types

28
V* SINGLE VANE PUMPS

SINGLE VANE PUMP TYPE VC-10

FLOW AND INPUT POWER DIAGRAMS 2


l/min. Gal./min.

38 10
Max. pressure (180 bar) 3 gal (7 bar)
34 9
3 gal (180 bar)

SINGLE VANE PUMPS


30 8
Pressure (7 bar) 7
27
23 6
CV Kw
19 5
20 14,9 1 gal (7 bar)
15 4
3 gal (180 bar)
18 13,4 3
11 1 gal (180 bar)
16 11,9 2
8
14 10,4
4 1
12 8,9
0 0
10 7,4
0 800 1600 2400 3200 4000 4800 R.P.M.
8 1 gal (180 bar)
6
6 4,5 l/min. Gal./min.
4 3
61 16
2 1,5
3 gal (7 bar)
1 gal (7 bar) 57 6 gal (7 bar)
15
0
0 53 14
800 1600 2400 3200 4000 4800 R.P.M. 6 gal (180 bar)
49 13
CV Kw 45 12
4 gal (7 bar)
42 11
26 19,4 4 gal (180 bar)
6 gal (180 bar) 38 10
24 17,9
34 9
22 16,4
4 gal (180 bar)
30
20 14,9 2 gal (7 bar)8
27 7
18 13,4 2 gal (180 bar)
11,9 23 6
16
2 gal (180 bar) 19 5
14 10,4
8,9
15
Bs
4
12
10 7,4 11 3
8 2
8 6
4,5 4 1
6
4 3 0 0
6 gal (7 bar) 0 800 1600 2400 3200 4000 4800 R.P.M.
2 4 gal (7 bar) 1,5
2 gal (7 bar)
0 l/min. Gal./min.
0 800 1600 2400 3200 4000 4800 R.P.M. 64 17
7 gal (7 bar)
61 16
7 gal (180 bar)
CV Kw 57 15
24 17,9 53 14
5 gal (180 bar) 5 gal (7 bar)
22 16,4 49 13
7 gal (180 bar)
20 14,9 45 12
18 13,4 42 11
16 11,9 38 10
14 10,4 34 9
5 gal (180 bar)
12 8,9 30 8
10 7,4 27 7
8 6 23 6
6 4,5 19 5
4 3 15 4
7 gal (7 bar)
2 1,5 11 3
5 gal (7 bar)
0 8 2
0 800 1600 2400 3200 R.P.M. 0 800 1600 2400 3200 R.P.M.
29
V* SINGLE VANE PUMPS

SINGLE VANE PUMP TYPE VC-20

FLOW SPEED (rpm)


2 PRES (BAR) Nominal
Power
CONNECTION WEIGHT
Lts.at Gal.at Reduction (Kgs.)
1000 rpm 1200 rpm (2) Min. Max. Contin. Intermit. (3) Inlet Outlet
19 6 2,8 3400 3,9
22 7 4,2 3000 4,4
26 8 4,5 2800 155 5,1 1 1/4" NPT 3/4" NPT
600 180 7,3
29 9 4,8 2800 5,6 1 1/4" BSP 3/4" BSP
36 11 4,8 2500 6,5
39 12 5,4 2400 7,5
42 13 6,0 2400 140 8,1

(2) & (3) see page 27.

See shaft types and measures

Dimension
Galon

Num. Inlet Outlet

02 1" 1/4 BSP 3/4" BSP

04 1" 1/4 NPT 3/4" NPT

Nº1 Shaft

Contact TDZ or your nearest


distributor for other shaft types

30
V* SINGLE VANE PUMPS

SINGLE VANE PUMP TYPE VC-20

FLOW AND INPUT POWER DIAGRAMS 2

Max. pressure (180 bar) Min. Pressure (7 bar)

SINGLE VANE PUMPS


CV Kw CV Kw
40 29,8 40 29,8
13 gal (180 bar) 11 gal (180 bar) 12 gal (180 bar)
35 26,1 35 26,1
8 gal (180 bar)
9 gal (180 bar)
30 22,4 30 22,4
25 18,6 25 18,6
7 gal (180 bar) 6 gal (180 bar)
20 14,9 20 14,9
15 11,2 15 11,2
10 7,5 10 7,5
13 gal (7 bar) 9 gal (7 bar) 12 gal (7 bar) 8 gal (7 bar)
5 11 gal (7 bar) 3,7 5 6 gal (7 bar)
3,7
7 gal (7 bar)
0 0
400 800 1200 1600 2000 2400 2800 R.P.M. 400 800 1200 1600 2000 2400 2800 3200 R.P.M.

l/min. Gal./min. l/min. Gal./min.


106 28 106 28
13 gal (7 bar)

98 26 98 26

13 gal (180 bar) 12 gal (7 bar)


91 24 91 24
11 gal (7 bar) 12 gal (180 bar)

11 gal (180 bar)


83 22 83 22

9 gal (7 bar)
76 20 76 20
8 gal (7 bar)
9 gal (180 bar)
68 18 68 18
7 gal (7 bar) 8 gal (180 bar)

6 gal (7 bar)
61 16 61 16

7 gal (180 bar) 6 gal (180 bar)


53 14 53 14

45 12 45 12

38 10 38 10

30 8 30 8

23 6 23 6

15 4 15 4

8 2 8 2

0 0 0 0
400 800 1200 1600 2000 2400 2800 R.P.M. 400 800 1200 1600 2000 2400 2800 3200 R.P.M.

31
V* SINGLE VANE PUMPS

SINGLE VANE PUMP TYPE VK-20 Y VQ-20

2 FLOW SPEED (rpm) PRES (BAR) CONNECTION WEIGHT


Min. Max. Contin. Intermit. Inlet Outlet (Kgs.)
Lts.at 1000 rpm 8 18 27 29 36 39 46
Gal.at 1200 rpm 2 5 8 9 11 12 14 600 2500 175 210 Ø 1 1/2" Ø 3/4" 12

See shaft types


and measures

Nº1 Shaft Nº151 Shaft

Diametral pitch: 16/32


Tooth number: 13

32
V* SINGLE VANE PUMPS

SINGLE VANE PUMP TYPE VK-20 Y VQ-20

FLOW AND INPUT POWER DIAGRAMS 2

Max. pressure (210 bar) Min. Pressure (7 bar)

SINGLE VANE PUMPS


l/min. Gal/min. l/min. Gal/min.

90 23,78 90 23,78
14 gal (7 bar)
80 21,13 80 21,13
14 gal (210 bar)
12 gal (7 bar)
70 18,49 70 18,49
12 gal (210 bar) 11 gal (7 bar)
60 15,85 60 15,85
8 gal (7 bar) 11 gal (210 bar)
9 gal (7 bar)
50 13,21 50 13,21
8 gal (210 bar) 9 gal (210 bar)

40 10,58 40 10,58
5 gal (7 bar)
30 7,93 30 7,93
5 gal (210 bar)

20 5,28 20 5,28
2 gal (7 bar)
10 2,64 10 2,64
2 gal (210 bar)

400 800 1200 1500 2000 R.P.M. 400 800 1200 1500 2000 R.P.M.

CV Kw
32,18 24

9 gal (210 bar)


26,28 20 CV Kw
12 gal (210 bar)

37,55 28
21,46 16 11 gal (210 bar)

32,18 24
5 gal (210 bar)
16,09 12
14 gal (210 bar)
26,28 20
10,73 8 8 gal (210 bar)

21,46 16
5,36 4
9 gal (7 bar)
12 gal (7 bar) 16,09 12
5 gal (7 bar)
0

10 7,5 10,73 8

2 gal (210 bar)

5 3,75 5,36 4
14 gal (7 bar)
2 gal (7 bar) 11 gal (7 bar)
8 gal (7 bar)

400 800 1200 1500 2000 R.P.M. 400 800 1200 1500 2000 R.P.M.

33
V* SINGLE VANE PUMPS

SINGLE VANE PUMP TYPE VS-25 & VQ-25

FLOW SPEED (rpm) PRES (BAR) CONNECTION WEIGHT


2 Inlet Outlet
Lts.at 1000 rpm 26 40 45 55 60 67 80* 88* Min. Max. Contin. Intermit. (Kgs.)
Gal.at 1200 rpm 8 12 14 17 19 21 24* 27* 600 2500* 175 210* Ø1”1/2 Ø1” 15

*See page 27.


DIMENSIONS IN MILLIMETRES 1" = 25.4 millimetres

See shaft types and measures

Outlet

Inlet

Nº1 Shaft Nº11 Shaft Nº86 Shaft

Diametral pitch: 16/32


Tooth number: 13

Enquire about other types of shafts

34
V* SINGLE VANE PUMPS

SINGLE VANE PUMP TYPE VS-25 & VQ-25

FLOW AND INPUT POWER DIAGRAMS 2

SINGLE VANE PUMPS


l/min US Gal/min

160 42,3

140 37,0

120 21 21
31,7
19 19

100 17 17 26,4

80 14 14 21,1
12
12

60 15,9

40 10,6

20 5,3

500 1000 1500 2000 2500 R.P.M.

0 BAR 210 BAR

HP Kw
80 59,7
21

70 52,2
19
17
60 44,7

14
50 37,3
12

40 21 29,8
19
17
30 22,4
14
12

20 14,9

10 7,5

500 1000 1500 2000 2500 R.P.M.

100 BAR 210 BAR

35
V* SINGLE VANE PUMPS

SINGLE VANE PUMP TYPE VS-35 & VQ-35

2 FLOW SPEED (rpm) PRES (BAR) CONNECTION WEIGHT

Lts.at 1000 rpm 66 81 97 112 121 142* Min. Max. Contin. Intermit. Inlet Outlet (Kgs.)
Gal.at 1200 rpm 21 25 30 35 38 45* 600 2400* 175 210* Ø2" Ø1"1/4 23

*See page 27. * For further details see general chart

DIMENSIONS IN MILLIMETRES 1" = 25.4 millimetres

See shaft types and measures

Outlet

Inlet

Nº1 Shaft Nº11 Shaft Nº86 Shaft

Diametral pitch: 12/24


Tooth number: 14

Enquire about other types of shafts

36
V* SINGLE VANE PUMPS

SINGLE VANE PUMP TYPE VS-35 & VQ-35

FLOW AND INPUT POWER DIAGRAMS 2

SINGLE VANE PUMPS


l/min US Gal/min

320 84,5

280 74,0

240 63,4
38
38
35
35
200 52,8
30 30

160 42,3
25 25

120 21 21 31,7

80 21,1

40 10,6

500 1000 1500 2000 2500 R.P.M.

0 BAR 210 BAR

HP Kw

160 119,3

140 104,4

120 89,5
38

100 35
74,6
30

80 59,6
25
38
21 35
60 30 44,7
25

40 21
29,8

20 14,9

500 1000 1500 2000 2500 R.P.M.

100 BAR 175 BAR

37
V* SINGLE VANE PUMPS

SINGLE VANE PUMP TYPE VS-45 & VQ-45

SPEED (rpm) PRES (BAR) CONNECTION WEIGHT


2 FLOW

Lts.a 1000 rpm 138 148 162 180 193 214 240 Mín. Máx. Contin. Intermit. Inlet Outlet (Kgs.)
Gal. a 1200 rpm 42 47 50 57 60 67 75 600 2200* 155 175 Ø3" Ø1"1/2 35,5
* For further details see general chart

DIMENSIONS IN MILLIMETRES 1" = 25.4 millimetres

See shaft types and measures

Nº1 Shaft Nº11 Shaft Nº86 Shaft

Diametral pitch: 12/24

Tooth number: 14

Enquire about other types of shafts


38
V* SINGLE VANE PUMPS

SINGLE VANE PUMP TYPE VS-45 & VQ-45

FLOW AND INPUT POWER DIAGRAMS 2

SINGLE VANE PUMPS


l/min US Gal/min

560 147,9

490 129,4

420 111,0

350 60
60
92,5
57
57
50
280 50
74,0
47 47
42 42

210 55,5

140 37,0

70 18,5

500 1000 1500 2000 2500 R.P.M.

0 BAR 175 BAR

HP Kw
200 149,1

175 60 130,5
57

150 111,8
50
47

125 42
93,2

100 74,6
60
57
50
75 47 55,9
42

50 37,3

25 18,6

500 1000 1500 2000 2500 R.P.M.

100 BAR 175 BAR

39
DT6TSINGLE VANE PUMPS

DT-6 SINGLE VANE PUMPS ORDERING CODE

DT6I- C - * - B - 17 - 1 - R - 00 - B - 1 - M

Special Features

1: NBR
Seal Class
2: VITON

Design letter

Porting combination,(viewed from shaft end)


(see diagrams)
R: clockwise
Direction of rotation L: counterclockwise

Type of Shaft (see particular pump model)

Flow (see particular pump model)

Bidirectional
M* 1 shaft seal
P* 2 shaft seals

Size (C, D, E)

Vane pumps “DT” series

40
DT6 SINGLE VANE PUMPS - GENERAL CHARACTERISTICS

SINGLE PUMPS
Pump Cartridge Theoretical Maximum Max. speed Min. speed Weight Front flange SAE 4 holes flange
Model model displacement Pressure rpm rpm Kgs Standard
3
Cm /rev SAE j744c Suction Pressure
ISO 3019-1

003 10.8
005 17.2
006 21.3
008 26.4
010 34.1
012 37.1 275 2800 400 15 SAE B 1 ½” 1”
DT6C 014 46.0
017 58.3
020 63.8
022 70.3
025 79.3
028 88.8 210 2500
031 100
DT6CP Pump model only mount B14 to B31 cartridges

014 47.6
020 66.0
024 79.5
028 89.7
031 98.3 240 2500 400 24 SAE C 2” 1 1/4”
DT6D 035 111.0
038 120.3
042 136.0
045 145.7 2200
050 158.0 210
061 190.5 120 1800
042 132.3
045 142.4
050 158.5
DT6E 052 164.8
062 196.7 240 2200 400 44 SAE C 3” 1 ½”
066 213.3
072 227.1
085 269.8 90 2000

00 01 02 03
P P-S P P

S S

41
DT6C OPERATING CHARACTERISTICS

FLOW
2 SPEED (rpm) PRESSURE (bar) WEIGHT
Mín. Máx. Intermit. Contin. (Kgs.)
Lts/min.at 1000 rpm 11 17 21 26 34 37 46 58 64 70 79 89 100
Gal/min.at 1200 rpm 3 5 6 8 10 12 14 17 20 22 25 28 31 400 2800* 275 240* 15

* See page 41 for further information about speed & pressure.

L/min US Gal/min Kw. HP

300 79,36 90 120,6

80 107,2
250 66,13 31
70 93,8
31 28

200 28 52,91 60 25 80,4


25 22
22 50 20
67,0
150 20 39,68 17
17 40 53,6
14
100 14 26,45 30 40,2
12
12 10
10
20 8 26,8
8
13,22 6
50 6
5
5 10 13,4
3 3

0 0
0 1000 2000 3000 R.P.M. 0 1000 2000 3000 R.P.M.

Theoretical Flow (0 Bar) Theoretical Input Power at 200 Bar

To calculate the real flow at a given operating pressure, To calculate the theoretical input power at other
substract the internal leakage value for this pressure pressures and speeds, use the formula:
(see diagram below) from the theoretical flow.
(See diagram above). Q(L/min.) x P(Bar)
P(Kw)
600
Where Q is the theoretical flow (upper left diagram)
and P the operating pressure.

To calculate the real input power, add to the theoretical


power the hydromechanical power losses.
(see diagram below).

N=2800
24 cSt
N=2500 24 cSt
10 cSt N=1000
24 5
Internal leaking qVs [l/min.]

21
4
Power loss Ps [Kw]

18
15 3
12
9 2
6
1
3

0 0
0 35 70 105 140 160175190 210 240 275 0 35 70 105 140 160 175190 210 240 275

Pressure p [bar] Pressure p [bar]


Do not operate pump more than 5 seconds at any speed or viscosity
if internal leakage is more than 50 % of theoretical flow

42
DIMENSIONS - SINGLE VANE PUMPS DT6C

45,5
174,5 40,7 7,9
146,0 7,9 24,5
73,0
24,5 1,5 x 45º
1,5 x 45º

Shaft Code 3 Shaft Code 4


SAE B Splined shaft 1-J498b
16/32 d.p. - 13 teeth SAE BB Splined shaft 1-J498b
Ø14,2 30º Pressure angle 16/32 d.p. - 15 teeth
30º Pressure angle

161,5 71,4
82,3 38,1
9,7 38,1
Mounting Torque 159Nm
7,9
6,35 Max Key 6,35/6,30
76,2

Ø 101,60/101,55
134,6

Ø 51,3
Ø22,22 / 22,20
M8 x 16,0

24,54 Max

1,5 x 45º

1,3 x 45º
Shaft Code 1
3/8-16 UNC x 19.05 Deep
12,7
35,7 26,2 58,2
1/2-13 UNC x 22.35 Deep 17,85 13,10 7,9
31,8

Key 4,762/4,712
69,86

52,4
26,2
34,93

24,54 Max
Ø22,22 / 22,20

1,5 x 45º

Ø38,1 Suction Ø25,4 Pressure


Shaft Code 2
11
43
DT6D OPERATING CHARACTERISTICS

FLOW
2 SPEED (rpm) PRESSURE (bar) WEIGHT
Mín. Máx. Intermit. Contin. (Kgs.)
Lts/min.at 1000 rpm 48 66 80 90 98 111 120 136 146 158 191
Gal/min.at 1200 rpm 14 20 24 28 31 35 38 42 45 50 61 400 2500* 240 210 24

* See page 41 for further information about speed & pressure.

L/min US Gal/min Kw. HP


350 92,59 120 160,8
61 110 61 147,4
300 79,36 100 134,0
50 50
90 120,6
250 45 66,13 45
42 80 42 107,2
38 70 38 93,8
200 52,91
35 35
31 60 80,4
31
150 28 39,68 50 28 67,0
24 24
20 40 20 53,6
100 26,45
14 30 14 40,2

50 13,22 20 26,8
10 13,4
0 0
0 500 1000 1500 2000 2500 R.P.M. 0 500 1000 1500 2000 2500 R.P.M.

Theoretical Flow (0 Bar) Theoretical Input Power at 200 Bar

To calculate the real flow at a given operating pressure, To calculate the theoretical input power at other
substract the internal leakage value for this pressure pressures and speeds, use the formula:
(see diagram below) from the theoretical flow.
(See diagram above). Q(L/min.) x P(Bar)
P(Kw)
600
Where Q is the theoretical flow (upper left diagram)
and P the operating pressure.

To calculate the real input power, add to the theoretical


power the hydromechanical power losses.
(see diagram below).

N=2400
24 cSt N=1500 24 cSt
10 cSt N=1000
32 6
Internal leaking qVs [l/min.]

28 5
Power loss Ps [Kw]

24
4
20
16 3
12 2
8
1
4

0 0
0 35 70 105 140 160 175 190 210 240 0 35 70 105 140 160 175 190 210 240

Pressure p [bar] Pressure p [bar]

44
DIMENSIONS - SINGLE VANE PUMPS DT6D

55,1

212,4 7,9
181,0 38,1
90,5
2,3 x 45º
Ø17,5

Shaft Code 3
SAE C Splined shaft 1-J498b
12/24 d.p. - 14 Teeth
30º Pressure angle

184,9 83,6
87,4 38,1 12,7
7,9
6,35 Max
Shaft Code 1
49,3
Key 7,94/7,89
77,7
7,9

M10 x 20,0 48,0


82,6

2,3 x 45º
Ø127,00/126,95
156,7

Ø64,3
Ø31,75/31,70

35,27 Max

2,3 x 45º

1,3 x 45º

Shaft Code 4
7/16-14 UNC x 22.35 No SAE Splined shaft 1-J498b
15,7 73,2 12/24 d.p. - 14 Teeth
4 Orifices1/2-13 UNC x 23.88 42,9 30,2 30º Pressure angle
38,1
Mounting torque 187 Nm
Key 7,94/7,89
77,7

58,7

Ø 31,75/31,70

35,27 Max

2,3 x 45º

Ø50,8 Suction Ø31,8 Pressure Shaft Code 2


45
DT6E OPERATING CHARACTERISTICS

FLOW
2 SPEED (rpm) PRESSURE (bar) WEIGHT
Mín. Máx. Intermit. Contin. (Kgs.)
Lts/min.at 1000 rpm 132 142 156 165 197 213 227 270
Gal/min.at 1200 rpm 42 45 50 52 62 66 72 85 400 2200* 240 210 44

* See page 41 for further information about speed & pressure.

L/min US Gal/min Kw. HP


550 145,50 180 241,2
170 227,8
500 132,27 160 214,4
85 85
450 119,04 150 201,0
140 187,6
72 72
400 105,82 130 174,2
66 120 66
160,8
350 62
92,59 110 62
147,4
300 52 79,36 100 52 134,0
50 90 50 120,6
250 45 66,13 45
80 42
107,2
42
200 52,91 70 93,8
60 80,4
150 39,68 50 67,0
40 53,6
100 26,45 30 40,2
50 13,22 20 26,8
10 13,4

0 500 1000 1500 2000 2500 R.P.M. 0 500 1000 1500 2000 2500 R.P.M.

Theoretical Flow (0 Bar) Theoretical Input Power at 200 Bar

To calculate the real flow at a given operating pressure, To calculate the theoretical input power at other
substract the internal leakage value for this pressure pressures and speeds, use the formula:
(see diagram below) from the theoretical flow.
(See diagram above). Q(L/min.) x P(Bar)
P(Kw)
600
Where Q is the theoretical flow (upper left diagram)
and P the operating pressure.

To calculate the real input power, add to the theoretical


power the hydromechanical power losses.
(see diagram below).

N=2200
24 cSt N=1500 24 cSt
10 cSt N=1000
36 6
Internal leaking qVs [l/min.]

32
5
Power loss Ps [Kw]

28
24 4
20
3
16
12 2
8
1
4
0 0
0 35 70 105 140 160175 190 210 240 0 35 70 105 140 160 175 190 210 240

Pressure p [bar] Pressure p [bar]

46
DIMENSIONS - SINGLE VANE PUMPS DT6E

55,9 62,2
213
181 7,9 7,9
90,5 38,1 31,5
Ø 147,6

2,3 x 45º
2,3 x 45º

Ø17,5
Shaft Code 3 Shaft Code 4
SAE C Splined shaft 1-J498b SAE C-C Splined shaft
12/24 d.p. - 14 Teeth 1-J498b 12/24 d.p. -
30º Pressure angle 17 Teeth
30º Pressure angle

Mounting Torque 187 Nm 225,3 90,9


110 52,3 12,7
7,9
6,35 Max 50,8

Key 9,52/9,47
98,6

M10 x 20

Ø127,00/126,95
Ø 38,10/38,05

42,36 Max
Ø 76,2
187,5

2,3 x 45º

1,3 x 45º

Shaft Code 1
SAE C-C

61,9
4 Orifices 5/8-11 UNC x 23.88 17,5
61,9 35,7

38,1

Key 7,94/7,89
Ø 31,75/31,70

Ø35,31 Max
69,8
106,4

2,3 x 45º

Shaft Code 2
4 Orifices 1/2-13 UNC x 23.37

Ø 76,20 Suction Ø 37,10 Pressure

47
48
THRU DRIVE SINGLE VANE PUMPS

THRU DRIVE SINGLE VANE PUMPS


V**T thru drive single vane pumps

See single V* pumps for displacement & power diagrams (Pages 35, 37.39)

V*7TC thru drive pump with V*64 double pump

49
THRU DRIVE SINGLE VANE PUMPS

V* THRU DRIVE SINGLE VANE PUMPS ORDERING CODE

2
F3 VS 7T C 60 D 86 A A
1 2 3 4 5 6 7 8 9

1 - "F3" means special seals for fire-resistant fluids. Omit if not required

2 - Pump Type:

VS = 12 vane pump, industrial use (very quiet), UNC threads


VQ = 10 vanes and bronze plates pump, mobile use, UNC threads

3 - Pump model: 4T, 6T and 7T.

4 - Rear pump mounting: With SAE mounting flange, 2-bolts.


A: SAE-A mounting flange
B: SAE-B mounting flange
C: SAE-C mounting flange

5 - Flow: In US Gallons per minute at 1200 rpm and 7 bar.

6 - D = Right-hand direction of rotation (Clockwise)


Y = Left-hand direction of rotation.
(To check the direction of rotation view from the shaft end).

7 - Shaft type:
1: Parallel keyed
11: Splined
86: Heavy duty parallel keyed

8 - Outlet position, (viewed from shaft):


A: In line with inlet
B: 90° on the right from inlet (Clockwise from inlet)
C: 180° from inlet
D: 90° on the left from inlet (Counterclockwise from inlet)

9- Rear flange positions, (viewed from the flange):


SAE A flanges:
A: 45º on the right (Clockwise)
B: 45º on the left (Counterclockwise)

SAE-B and SAE-C flanges:


A: In line with in-front flange
B: 90° rotated

50
THRU DRIVE SINGLE VANE PUMPS

THRU DRIVE SINGLE VANE PUMPS CHARACTERISTICS

2
FLOW SPEED PRESSURE Nominal CONNECTION WEIGHT
TYPE Gal. At Reduction
(rpm) (Bar) Power (Kgs.)
Lts.at

THRU DRIVE SINGLE VANE PUMPS


1000 rpm 1200 rpm (1) Mín. Máx. Contin. Intermit. (2) Inlet Outlet
26 8 4,5 6,9
40 12 5,7 2500 10,4
45 14 5,7 1800 175 210 11,6
VS4T 55 17 5,8 600 (VS) 13,8 Ø64 Ø25,4 19,5
VQ4T 60 19 5,8 14,6
67 21 6 16,8
80 24 6,2 1500 125 150 20,3
88* 27 6,5 23,8
66 21 8,6 16,8
81 25 9 2400 20,3
VS6T 97 30 10 1800 175 210 24,3 Ø76 Ø31,8 29,5
600 (VS)
VQ6T 112 35 11,4 27,4
121 38 11,4 29,3
142 45 13,1 1500 125 150 33,3
138 42 15 32,3
148 47 15,7 36,3
162 50 14,3 2200 37,9
VS7T 180 57 17,9 600 43,2 Ø89 Ø38,1 38
1800 155 175
VQ7T 193 60 18,6 (VS) 46,1
214 67 22 51,2
240 75 26 57,4

(1) Delivery flow reduction in Ltrs./min. at 100 Bar. 22 cST of oil viscosity at operating temperature. To calculate the approximate
delivery flow at a given pressure and speed, use the following formula with flow reduction and theoretical flow values shown in
the chart. Flow reduction values are independent of shaft speed.

Approx. outpout flow (Ltrs./min.) = Theoretical flow x R.P.M - Reduction Pressure (bar)
1000 100
(2) Nominal power in H.P. at 100 Bar and 1000 RPM (to convert into Kw multiply by 0.735).
To obtain the real input power at different pressure and revolutions, use the formula as follows:

Real input power = Input power x R.P.M x Pressure (bar)


1000 100
REAR PUMP MOUNTING
The mounted pump to the V**T* should have the shaft shown below:

Mounted pump shaft


Model
DP splined Teeth Press angle Flange
V**TA 16/32 9 30º SAE-A

V**TB 16/32 13 30º SAE-B

V**TC 12/24 14 30º SAE-C

TRANSMISSIBLE MAXIMUM TORQUE


The torque of the V**T plus the torque of the rear pump, in pressure, shall be equal to or less than the below torques:

V*4T V*6T V*7T


Shaft Max. Torque Shaft Max. Torque Shaft Max. Torque
Nm Nm Nm
1 313 1 392 1 588
11 313 11 568 11 803
86 392 86 588 86 803

MAXIMUM TORQUE OF THE MOUNTED REAR PUMP


The torque of the mounted pump to the V**T rear pump, in pressure, shall be equal to or less than the indicated torques on next page.

51
THRU DRIVE SINGLE VANE PUMPS

REAR FLANGE MOUNTING OF THE V**T*


THRU DRIVE PUMP DIMENSIONS

2
DIMENSIONS IN MILLIMETRES 1" = 25.4 millimetres

V*4TA, V*6TA & V*7TA


Rear Torque for screw 65 Nm.
Flange Max Torque
(connection) Nm

A 130

B 315

C 440 (V*6TC)
700 (V*7TC)

V*4TB, V*6TB & V*7TB


Torque for screw 65 Nm.

V*6TC & V*7TC


Torque for screw 65 Nm.

52
THRU DRIVE SINGLE VANE PUMPS

THRU DRIVE PUMPS VS4T & VQ4T

2
DIMENSIONS IN MILLIMETRES 1" = 25.4 millimetres

THRU DRIVE SINGLE VANE PUMPS


Nº1 Shaft Nº11 Shaft Nº86 Shaft

Tooth number: 13

Diametral pitch: 16/32

Enquire about other types of shafts

53
THRU DRIVE SINGLE VANE PUMPS

THRU DRIVE PUMPS VS6T & VQ6T

2
DIMENSIONS IN MILLIMETRES 1" = 25.4 millimetres

Model A

V*6TA 20
V*6TB 30
V*6TC 38

Nº1 Shaft Nº11 Shaft Nº86 Shaft

Diametral pitch: 12/24


Tooth number:14

Enquire about other types of shafts

54
THRU DRIVE SINGLE VANE PUMPS

THRU DRIVE PUMPS VS7T & VQ7T

2
DIMENSIONS IN MILLIMETRES 1" = 25.4 millimetres

THRU DRIVE SINGLE VANE PUMPS


Model A

V*7TA 20
V*7TB 30
V*7TC 38

Nº1 Shaft Nº11 Shaft Nº86 Shaft

Diametral pitch: 12/24


Tooth number:14

Enquire about other types of shafts

55
56
DOUBLE VANE PUMPS

DOUBLE VANE PUMPS


BHP, VQ, VS and DT6 Double vane pumps
(mobile and industrial applications)

(See single pumps for displacement & power diagrams)

57
BHP & V* DOUBLE VANE PUMPS

BHP & V* DOUBLE VANE PUMPS ORDERING CODE

2 F3 VS 43 21 8 D 1 A A
1 2 3 4 5 6 7 8 9
1 - "F3" means special seals for fire-resistant fluids. Omit if not required

2 - Pump Type:

BHP = 10 vane pump, mobile and industrial uses, metrics threads.


VS = 12 vane pump, (except the cover end cartridge of the VS*3 pump), industrial uses (very
quiet), UNC threads.
VQ = 10 vane pump, bronze plates, mobile uses, UNC threads.

3 - Model of pump: 33,42,42V,43,63,64,73,74 y 76.


V*42 pump may include in the rear cartridge a cover with flow regulating and pressure limiter
valves. If so, add one "V": VS42V.

4 - Pump flow at shaft side: BHP33 model in litres per minute at 1000 rpm and 7 Bar.
All the other models in US gallons per minute at 1200 rpm and 7 Bar.
(See flow chart).

5 - Pump flow at cover side: BHP33 and VS42-VQ42 models in litres per minute
at 1000 rpm and 7 Bar. All the other models in gallons per minute at 1200 rpm and 7 Bar.
(See flow chart).

6 - D = Right-hand direction of rotation (Clockwise)


Y = Left-hand direction of rotation.
(To check the direction of rotation view from the shaft end).

7 - Shaft type:
1: Parallel keyed
2: Splined, (only mounted in BHP 33 model)
11: Splined
86: Heavy duty parallel keyed

8 - Shaft end outlet position, (viewed from shaft):


A: Outlet in line with inlet
B: 90° clockwise from inlet
C: 180° from inlet
D: 90° counterclockwise from inlet (Viewed from shaft)

9- Cover end outlet position, (viewed from shaft):


A: 45º clockwise from inlet
B: 135º clockwise from inlet
C: 135° counterclockwise from inlet
D: 45° counterclockwise from inlet Shaft end pump
(Viewed from shaft)

Cover end pump

58
DOUBLE VANE PUMPS

BHP AND V* DOUBLE VANE PUMP CHARACTERISTICS

SHAFT END COVER END 2


FLOW PRESSURE FLOW PRESSURE Nominal WEIGHT
TYPE MAX. Nominal
MAX.
Lts.at Gal. At Reducc. rpm
(Bar) Power
Lts.a Gal. a Reducc. rpm
(Bar) Power (Kgs.)
2
1000 rpm1200 rpm (2) Contin. Interm. (3) 1000 rpm 1200 rpm (2) Contin. Interm. (3)

6 2 0,9 1,9 6 2 0,9 1,9


16 5 1,7 4,3 16 5 1,7 4,3
18 6 2,8 5,3 18 6 2,8 5,3
25 8 4,5 6,9 25 8 4,5 6,9
BHP33 27 9 4,8 2500 150 175 7,6 27 9 4,8 2500 150 175 7,6 15
35 11 4,8 8,8 35 11 4,8 8,8
38 12 5,4 10,2 38 12 5,4 10,2
44 14 6,6 2000 11,9 44 14 6,6 2000 11,9
50 16 7,8 1500 100 125 13,6 50 16 7,8 1500 100 125 13,6

26 8 4,5 6,9
40 12 5,7 10,4
2500 7 2,2 0,7 1,8

DOUBLE VANE PUMPS


45 14 5,7 11,6
VS42 55 17 5,8 1800 175 210 8 2,5 1,1 2
(VS) 13,8 10 3,2 1,1 2500 150 175 2,5 16
VQ42 60 19 5,8 15,2 3
6 12 3,8 1,1
(1) 67 21 16,8 15 4,7 1,1 3,7
80 24 6,2 1500 125 150 20,3
88* 27 6,5
22,4
26 8 4,5 6,9 8 2 0,9 1,9
40 12 5,7 10,4 18 5 2,1 4
45 14 5,7 2500 11,6 27 8 2,8 6,6
VS43 55 17 5,8 1800 175 210 13,8 29 9 3,5 6,9 21
60 19 5,8 (VS) 15,2 2500 175 210
VQ43 6
36 11 4,3 7,3
67 21 16,8 39 12 4,3 7,4
80 24 6,2 20,3
1500 125 150 46 14 4,3 7,6
88* 27 6,5 22,4

16,8 8 2 0,9 1,9


66 21 8,6
2400 20,3 18 5 2,1 4
81 25 9
1800 175 210 24,3 27 8 2,8 6,6
VS63 97 30 10 29 9 3,5 2500 175 210 6,9 31
112 35 11,4 (VS) 27,4
VQ63 121 38 11,4 29,3 36 11 4,3 7,3
33,3 39 12 4,3 7,4
142 45 13,1 1500 125 150 46 14 4,3 7,6
26 8 4,5 6,9
66 21 8,6 16,8 40 12 5,7 10,4
81 25 9 2400 20,3 45 14 5,7 11,6
97 30 10 1800 175 210 24,3 2500 175 210 33
VS64 11,4
55 17 5,8
1800
13,8
112 35 (VS) 27,4 60 19 5,8 15,2
VQ64 121 38 11,4 29,3 67 21 6 (VS)
16,8
142 45 13,1 1500 125 150 33,3 80 24 6,2 20,3
1500 125 150
88* 27 6,5 22,4
138 42 15 32,3 8 2 0,9 1,9
148 47 15,7 36,3 18 5 2,1 4
162 50 14,3 2200 37,9 27 8 2,8 2500 6,6
VS73 180 57 17,9 1800 155 175 43,2 29 9 3,5 1800 175 210 6,9 46
193 60 18,6 (VS) 36 11 4,3 (VS) 7,3
VQ73 46,1
214 67 22 51,2 39 12 4,3 7,4
240 75 26 57,4 46 14 4,3 7,6

32,3 26 8 4,5 6,9


138 42 15
36,3 40 12 5,7 10,4
148 47 15,7
2200 37,9 45 14 5,7 11,6 45
162 50 14,3 2500 175 210
VS74 180 57 17,9 1800 155 175 43,2 55 17 5,8
1800
13,8
(VS) 60 19 5,8 15,2
VQ74 193 60 18,6 46,1
67 21 6
(VS)
16,8
214 67 22 51,2
80 24 6,2 1500 125 150 20,3
240 75 26 57,4 6,5
88* 27 22,4

138 42 15 32,3 66 21 8,6 16,8


148 47 15,7 2200 36,3 81 25 9 2400 20,3
VS76 162 50 14,3 1800 37,9 97 30 10 1800 175 210 24,3 55
155 175
180 57 17,9 (VS) 43,2 112 35 11,4 (VS) 27,4
VQ76 193 60 18,6 46,1 121 38 11,4 29,3
214 67 22 51,2 142 45 13,1 1500 125 150 33,3
240 75 26 57,4

* 27 gallons (88lts.) cartridge not mounted in VQ 42, VQ 43, VQ 64, VQ 74 vane pump model.
(1), (2) & (3) Please turn to next page
59
BHP DOUBLE VANE PUMPS

DOUBLE VANE PUMPS BHP-33

2DIMENSIONS IN MILLIMETRES 1" = 25.4 millimetres

Outlet
Inlet

Nº2 Shaft
Nº1 Shaft
Diametral pitch: 16/32

Tooth number: 13

Enquire about other types of shafts

Continued from previous page:


(1) There is a version for the pump of the cover end with flow regulating and pressure limiter valves whose reference V*42V
(2) Delivery flow reduction in Ltrs./min. at 100 Bar. 22 cST of oil viscosity at operating temperature. To calculate the
approximate delivery flow at a given pressure and speed, use the following formula with flow reduction and theoretical flow
values shown in the chart. Flow reduction values are independent of shaft speed.

Approx. output flow (Ltrs./min.) = Theoretical flow x R.P.M


1000
x Pressure (bar)
100
(3) Nominal power in H.P. at 100 Bar and 1000 RPM (to convert into Kw multiply by 0.735).
To get the real input power at different pressure and revolutions, use the formula as follows:

Real input power = Input power x R.P.M


1000
x Pressure (bar)
100

60
V* DOUBLE VANE PUMPS

DOUBLE VANE PUMPS VS-42 Y VQ-42

2
DIMENSIONS IN MILLIMETRES 1" = 25.4 millimetres
38 85,5 85

76,3 76,5

64
53

9,5

DOUBLE VANE PUMPS


225

3/8"x16 UNC
13
Ø25,4 Outlet Ø45 Inlet
1/2"x13 UNC

Ø14,3

52,4 77,7 Ø121

146
26,2 42,8 175
1/2"BSP Outlet

Nº1 Shaft Nº11 Shaft Nº86 Shaft

Tooth number: 13

Diametral pitch: 16/32

Enquire about other types of shafts

There is a version for the pump of the cover end with flow regulating and pressure limiter valves whose reference V*42V

61
V* DOUBLE VANE PUMPS

DOUBLE VANE PUMPS VS-43 Y VQ-43

2DIMENSIONS IN MILLIMETRES 1" = 25.4 millimetres

38 101,5 89,5

76,3 84

64
76,3

9,5 250
10,5
6,5

3/8"x16 UNC
13
Ø25,4 Outlet Ø64 Inlet

1/2"x13 UNC

Ø14,3
3/8"x16 UNC
Ø101,6 52,4 89 Ø121

47,6

146
26,2 50,8 22,2 175
Ø19 Outlet 3/4"BSP
(Optional outlet)
Nº1 Shaft Nº11 Shaft Nº86 Shaft

Tooth number: 13

Diametral pitch: 16/32

Enquire about other types of shafts

62
V* DOUBLE VANE PUMPS

DOUBLE VANE PUMPS VS-63 Y VQ-63

2
DIMENSIONS IN MILLIMETRES 1" = 25.4 millimetres

38 110,9 98

82,5 89,5

78
76,3

DOUBLE VANE PUMPS


9,5 275 22,5
6,5

7/16"x14 UNC
16
Ø31,8 Ø76 Inlet
5/8"x11 UNC

Ø17,5

3/8"x16 UNC
Ø127 58,7 106,3 Ø148

47,6

181
30,2 61,9 22,2
213
Ø19 Outlet
3/4"BSP
(Optional outlet)

Nº1 Shaft Nº11 Shaft Nº86 Shaft

Diametral pitch: 12/24

Tooth number: 14

Enquire about other types of shafts

63
V* DOUBLE VANE PUMPS

DOUBLE VANE PUMPS VS-64 Y VQ-64

2DIMENSIONS IN MILLIMETRES 1" = 25.4 millimetres

38 116,9 110

82,5 89,5

78
75

9,5 291 22,5


10,5

7/16"x14 UNC
16
Ø31,8 Outlet Ø76 Inlet
5/8"x11 UNC

Ø17,5
3/8"x16 UNC
Ø127 58,7 106,3 Ø148

52,4

181
30,2 61,9 26,2
213
Ø25,4 Outlet
3/4"BSP
(Optional outlet)
(Opcional)

Nº1 Shaft Nº11 Shaft Nº86 Shaft

Diametral pitch: 12/24

Tooth number: 14

Enquire about other types of shafts

64
V* DOUBLE VANE PUMPS

DOUBLE VANE PUMPS VS-73 Y VQ-73

2
DIMENSIONS IN MILLIMETRES 1" = 25.4 millimetres

43 120 120

93,7 102,5

85
76,3

DOUBLE VANE PUMPS


12,7 304 35
6,5

1/2"x13 UNC
16
Ø38,1 Outlet Ø89 Inlet
5/8"x11 UNC

Ø17,5
3/8"x16 UNC
Ø127 69,8 120,6 Ø148

47,6

181
35,8 69,8 22,2 213
Ø19 Outlet 3/4"BSP
(Optional outlet)

Nº1 Shaft Nº11 Shaft Nº86 Shaft

Diametral pitch: 12/24

Tooth number: 14

Enquire about other types of shafts

65
V* DOUBLE VANE PUMPS

DOUBLE VANE PUMPS VS-74 Y VQ-74

2DIMENSIONS IN MILLIMETRES 1" = 25.4 millimetres

43 120 136

93,7 102,5

83
75

12,7 325 35
10,5

1/2"x13 UNC
16
Ø38,1 Outlet Ø89 Inlet

5/8"x11 UNC

Ø17,5
3/8"x16 UNC
Ø127 69,8 120,6 Ø148

52,4

181
35,8 69,8 26,2
Outlet 213
Ø25,4 Outlet 3/4"BSP
(Optional outlet)

Nº1 Shaft Nº11 Shaft Nº86 Shaft

Diametral pitch: 12/24

Tooth number: 14

Enquire about other types of shafts

66
V* DOUBLE VANE PUMPS

DOUBLE VANE PUMPS VS-76 Y VQ-76

2
DIMENSIONS IN MILLIMETRES 1" = 25.4 millimetres

DOUBLE VANE PUMPS


Outlet

Inlet

Outlet

Nº1 Shaft Nº11 Shaft Nº86 Shaft

Diametral pitch: 12/24

Tooth number: 14

Enquire about other types of shafts

67
ORDERING CODE - SERIES DT

DT6 DOUBLE VANE PUMPS ORDERING CODE

DT6*I- CC - * - B -17/14 - 1 - R - 00 - B - 1 - M - 00

Special ports (only in DT6CC)

Special Features

1: NBR
Seal Class
2: VITON

Design letter

Porting combination (see diagrams)


(Viewed from shaft)
R: clockwise
Direction of rotation L: counterclockwise

Type of Shaft (see particular pump model)

Flow (see particular pump model)

Bidirectional
M* 1 shaft seal
P* 2 shaft seals
Size (CC, DC, EC, ED)

Vane pumps “DT6” series

68
DT61DOUBLE VANE PUMPS

GENERAL CHARACTERISTICS
DOUBLE VANE PUMPS
P1 P2 Front SAE 4 Holes
flange flange
Pump Cartridge Theoretical Maxim. Cartridge Theoretical Maxim. Maxim. Minim. Weight
standard
Model Model displacement Pressure Model displacement Pressure speed speed Kgs Suction Pressure
SAE j744c S P1 P2
3
Cm /rev Bar Cm3/rev Bar
ISO 3019-1

DT6CC/M 003 a 031 10.8 a 100 275 003 a 031 10.8 a 100 275 2800 400 SAE B 26 2 ½”ó 3” 1” 1” ó 3/4”
DT6DC/M 014 a 061 47.6 a 190.5 240 003 a 031 10.8 a 100 275 2800 400 SAE C 37 3” 1 1/4” 1”
DT6EC/M 042 a 085 132.3 a 269.8 240 003 a 031 10.8 a 100 275 2200 400 SAE C 55 3 ½” 1 ½” 1”
DT6ED/M 042 a 085 132.3 a 268.8 240 014 a 061 47.6 a 190.5 240 2200 400 SAE C 66 4” 1 ½” 1”

C - 025,028,031 - 2500 rpm maximum 028,031 - 210 bar max intermitent


D - 042,045,050 - 2200 rpm maximum 050 - 210 bar maximum intermitent - 061 - 120 bar maximum intermitent
E - 085 - 2000 rpm maximum - 90 bar maximum intermitent

Above mentioned values of maximum speed and maximum pressure are based on use of antiwear oil only.
Please contact TDZ for particular values when different fluids are used, (synthetic fluids, water in oil emulsions,
water glycol, etcetera)
DOUBLE VANE PUMPS - PORTING COMBINATION DT6CC-DT6DC-DT6EC
00 01 02 03 04 05 06 07
P1-P2 P1-P2 S-P1-P2 P1-P2 P1 P1 P1 P1-S
S S P2
S S P2 P2

S S-P2
08 09 10 11 12 13 14 15
P1-S P1-S P1 P1 P1 P1 P1 P1
P2 P2 P2 P2
S S S
P2 S
P2 P2 S P2 S
16 17 18 19 20 21 22 23
P1-S P1 P1 P1 P1 P1
P2 P2 P2 P1 P1
P2
S S S S
P2 P2 P2 P2
S S S
24 25 26 27 28 29 30 31
P1-S P1-S P1-S P1-S P1 P2 P1 P1
P2 P2 P1
P2
S S S S
P2 P2 P2 P2

DOUBLE VANE PUMPS - PORTING COMBINATION DT6ED


00 01 02 03 04 05 06 07
P1-P2 P1-P2 S-P1-P2 P1-P2 P1 P1 P1 P1-S
S S P2
S S P2 P2

S S-P2
08 09 10 11 12 13 14 15
P1-S P1-S P1 P1 P1 P1 P1 P1
P2 P2 P2 P2
S S S
P2 S
P2 P2 S P2
S= Suction port | P1= Shaft end pressure port | P2= Cover end pressure port
69
DT61DOUBLE VANE PUMPS

DOUBLE PUMPS DT6CC - OPERATING CHARACTERISTICS

2
SHAFT END SECTION
FLOW
2 SPEED (rpm) PRESSURE (bar) WEIGHT
Mín. Máx. Intermit. Contin. (Kgs.)
Lts/min.at 1000 rpm 11 17 21 26 34 37 46 58 64 70 79 89 100
Gal/min.at 1200 rpm 3 5 6 8 10 12 14 17 20 22 25 28 31 400 2800* 275 240* 15

* See page 41 for further information about speed & pressure.

COVER END SECTION

FLOW
2 SPEED (rpm) PRESSURE (bar) WEIGHT
Mín. Máx. Intermit. Contin. (Kgs.)
Lts/min.at 1000 rpm 11 17 21 26 34 37 46 58 64 70 79 89 100
Gal/min.at 1200 rpm 3 5 6 8 10 12 14 17 20 22 25 28 31 400 2800* 275 240* 15

* See page 41 for further information about speed & pressure.

DT6CC - FLOW & INPUT POWER DIAGRAMS

SHAFT END

See DT6C Single Pumps for flow and input power diagrams (page 42)

COVER END

See DT6C Single Pumps for flow and input power diagrams (page 42)

70
DT61DOUBLE VANE PUMPS

DOUBLE PUMPS DT6CC - DIMENSIONS


174,5
Suction and pressure Port dimenssion variables.
146
73 Thread Port A B C D E
S 3” 106,4 61,9 76,2 5/8”-11UNC x 28,4
S 2 ½” 88,9 50,8 63,5 1/2”-13UNC x 23,9
P1 1” 52,4 26,2 25,4 76,2
P2 3/4” 47,7 22,4 19,0 76,2
P2 1” 52,4 26,2 25,4 74,7

*Add the following numbers at the end of the

76,2
DT6CC reference depending your option.
Ø 14,3

Code 00* Code 01* Code 10* Code 11*


S 3” 3” 2 ½” 2 ½”
P1 1” 1” 1” 1”
P2 1” 3/4” 1” 3/4”
You may use suction “S” of 2 ½” for 126 cc/rev. maximum
You may use pressure port “P2” of 3/4” for 46 cc/rev.

DOUBLE VANE PUMPS


maximum

Shaft torque limits cc/rev x bar


Pump Shaft code V x P max (P1+P2)
Mounting Torque 159 Nm
1 14300 45,5
DT6CC 3 32670
7,9
5 20600
24,5
DT6CCW 2 21470 1,5 x 45º

265,6 71,4
88,2 101,6 38,1
9,7 38,1
7,9

6,35 Max

Key 6,35/6,30
84,1

M8 x 16
Ø 101,60/101,55
D

Ø 51,3

Shaft Code 3
28,22 Max

1,5 x 45º SAE BB Splined shaft


Ø 25,40/25,37
73,2

1-J498b 16/32 d.p. -


15 Teeth
30º Pressure angle

1,3 x 45º
Mounting Torque 61 Nm
Shaft Code 2 40,7
SAE BB 24,5
E - 4 Orifices 4 Orifices 3/8-16 UNC x 19.05 7,9
12,7
1,5 x 45º
26,2 58,2
B B 13,1 7,9
31,7

Key 4,762/4,712
52,4

Ø 22,225/22,20
A

Ø 24,53 Max
26,2
A

1,5 x 45º

Shaft Code 5
SAE B Splined shaft
1-J498b 16/32 d.p. -
13 Teeth
Ø C - Pressure Ø C - Suction Ø 25,4 - Pressure Shaft Code 1 30º Pressure angle
Keyed no SAE

71
DT61DOUBLE VANE PUMPS

DT6DC - OPERATING CHARACTERISTICS

2
SHAFT END SECTION
FLOW
2 SPEED (rpm) PRESSURE (bar) WEIGHT
Mín. Máx. Intermit. Contin. (Kgs.)
Lts/min.at 1000 rpm 48 66 80 90 98 111 120 136 146 158 191
Gal/min.at 1200 rpm 14 20 24 28 31 35 38 42 45 50 61 400 2500* 240 210 24

* See page 41 for further information about speed & pressure.

COVER END SECTION

FLOW
2 SPEED (rpm) PRESSURE (bar) WEIGHT
Mín. Máx. Intermit. Contin. (Kgs.)
Lts/min.at 1000 rpm 11 17 21 26 34 37 46 58 64 70 79 89 100
Gal/min.at 1200 rpm 3 5 6 8 10 12 14 17 20 22 25 28 31 400 2800* 275 240* 15

* See page 41 for further information about speed & pressure.

DT6DC - FLOW & INPUT POWER DIAGRAMS

SHAFT END

See DT6D Single Pumps for flow and input power diagrams (page 44)

COVER END

See DT6C Single Pumps for flow and input power diagrams (page 42)

72
DT61DOUBLE VANE PUMPS

DOUBLE PUMPS DT6DC - DIMENSIONS


212,3
55,1
181 77,7
90,5 7,9
7,9
38,1
48
2
2,3 x 45º
2,3 x 45º

82,6
Ø 17,5

Shaft Code 3 Shaft Code 4

DOUBLE VANE PUMPS


SAE C Splined shaft Splined no SAE shaft
1-J498b 12/24 d.p. - 1-J498b 12/24 d.p. -
Mounting Torque 187 Nm 14 Teeth 14 Teeth
30º Pressure angle 30º Pressure angle

286 83,6
109,5 114,3 38,1 12,7 Shaft Code 1
7,9 SAE C
6,35 Max 49,3
Key 7,95/7,90

M10 x 20
88,9
74,7

Ø 127,00/126,95
Ø 64,5
Ø 31,75/31,70

32,28 Max
73,9

2,3 x 45º

1,3 x 45º
Mounting Torque 68 Nm

Shaft Torque Limits (cc/rev x bar)


Pumps Shaft code V x P max (P1+P2)
1 43240
DT6DC 2 38996

4 Orifices 5/8-11 UNC x 28.44 4 Orifices 7/16-14 UNC x 22.86


15,7 73,2
4 Orifices 3/8-16 UNC x 19.05 7,9
22,4 62 30,2
38,1
Key 7,95/7,90
106,4

58,7
47,8

Ø 31,75/31,70

Ø 35,28 Max

2,3 x 45º

Ø 76 Suction Shaft Code 2


Ø 31,8 Pressure
Ø 25 Pressure

73
DT61DOUBLE VANE PUMPS

DT6EC - OPERATING CHARACTERISTICS

2
SHAFT END SECTION

FLOW
2 SPEED (rpm) PRESSURE (bar) WEIGHT
Mín. Máx. Intermit. Contin. (Kgs.)
Lts/min.at 1000 rpm 132 142 156 165 197 213 227 270
Gal/min.at 1200 rpm 42 45 50 52 62 66 72 85 400 2200* 240 210 44

* See page 41 for further information about speed & pressure.

COVER END SECTION

FLOW
2 SPEED (rpm) PRESSURE (bar) WEIGHT
Mín. Máx. Intermit. Contin. (Kgs.)
Lts/min.at 1000 rpm 11 17 21 26 34 37 46 58 64 70 79 89 100
Gal/min.at 1200 rpm 3 5 6 8 10 12 14 17 20 22 25 28 31 400 2800* 275 240* 15

* See page 41 for further information about speed & pressure.

DT6EC - FLOW & INPUT POWER DIAGRAMS

SHAFT END

See DT6E Single Pumps for flow and input power diagrams (page 46)

COVER END

See DT6C Single Pumps for flow and input power diagrams (page 42)

74
DT61DOUBLE VANE PUMPS

DOUBLE PUMPS DT6EC - DIMENSIONS


212,5 61 55,9
181 7,9

90,5 31,4
7,9 2
38,1
2,3 x 45º

2,3 x 45º

Ø 17,5 Shaft Code 4


SAE CC Splined shaft
1-J498b 12/24 d.p. -
17 Teeth Shaft Code 3

DOUBLE VANE PUMPS


30º Pressure angle
SAE C Splined shaft
1-J498b 12/24 d.p. -
Shaft Torque Limits (cc/rev x bar) 14 Teeth
30º Pressure angle
Pump Shaft Code V x P max (P1+P2)
Mounting Torque 187 Nm
1 72306
DT6EC 2 34590
3 61200

331,6 90,9
136,7 118,5 52,3 12,7 Shaft Code 1
7,9 SAE CC
6,35 Max 50,8

Key 9,52/9,47

M10 x 20
98,4
102,4
74,7

Ø 127,00/126,95
Ø 42,36 Max
Ø 38,10/38,05

Ø 76,2
2,3 x 45º
76,2

88,9

1,3 x 45º

Mounting Torque 68 Nm

4 Orifices 5/8-11 UNC x 29.46 4 Orifices 1/2-13 UNC x 23.36 61,9


17,5
26,2 69,2 23,4
7,9
4 Orifices 3/8-16 UNC x 19.05

Key 7,94/7,89
Ø 31,75/31,70

38,1
Ø 35,27 Max
120,6

69,8
52,4

2,3 x 45º

Ø 25,4 - Pressure
Shaft Code 2

Ø 88,9 - Suction Ø 37,1 - Pressure

75
DT61DOUBLE VANE PUMPS

DT6ED - OPERATING CHARACTERISTICS

2
SHAFT END SECTION

FLOW
2 SPEED (rpm) PRESSURE (bar) WEIGHT
Mín. Máx. Intermit. Contin. (Kgs.)
Lts/min.at 1000 rpm 132 142 156 165 197 213 227 270
Gal/min.at 1200 rpm 42 45 50 52 62 66 72 85 400 2200* 240 210 44

* See page 41 for further information about speed & pressure.

COVER END SECTION

FLOW
2 SPEED (rpm) PRESSURE (bar) WEIGHT
Mín. Máx. Intermit. Contin. (Kgs.)
Lts/min.at 1000 rpm 48 66 80 90 98 111 120 136 146 158 191
Gal/min.at 1200 rpm 14 20 24 28 31 35 38 42 45 50 61 400 2500* 240 210 24

* See page 41 for further information about speed & pressure.

DT6ED - FLOW & INPUT POWER DIAGRAMS

SHAFT END

See DT6E Single Pumps for flow and input power diagrams (page 46)

COVER END

See DT6D Single Pumps for flow and input power diagrams (page 44)

76
DT61DOUBLE VANE PUMPS

DOUBLE PUMPS DT6ED - DIMENSIONS

212,5
61 55,9
2
181 7,9
90,5 7,9
31,4
38,1
2,3 x 45º

2,3 x 45º

Ø 17,5

Shaft Code 4

DOUBLE VANE PUMPS


SAE CC Splined shaft
1-J498b 12/24 d.p. -
17 Teeth
30º Pressure angle
Shaft Code 3
Shaft Torque Limits (cc/rev x bar) SAE C Splined shaft
Pump Shaft Code V x P max (P1+P2) 1-J498b 12/24 d.p. -
Mounting Torque 187 Nm 14 Teeth
1 72306 30º Pressure angle
DT6ED 2 34590
3 61200
361,2 90,9
148,3 133,6 52,3 12,7
7,9 Shaft Code 1
6,35 Max 50,8 SAE CC

Key 9,52/9,47
98,4

M10 x 20
102,4
101,6

Ø 127,00/126,95
Ø 42,36 Max
Ø 38,10/38,05

Ø 76,2

2,3 x 45º
81

88,9

1,3 x 45º
Mounting Torque 187 Nm

4 Orifices 5/8-11 UNC x 29.97 4 Orifices 1/2-13 UNC x 23.36 62


17,5
4 Orifices 7/16-14 UNC x 23.87 77,7
30,2 35,7

Key 7,94/7,89
38,1
69,8
130,2
58,7

Ø 31,75/31,70

Ø 35,27 Max

2,3 x 45º

Shaft Code 2
Ø 29,5 - Pressure Cylindrical no SAE
Ø 101,6- Suction Ø 37,1 - Pressure

77
78
DT61TRIPLE VANE PUMPS

TRIPLE VANE PUMPS

DT6 Triple vane pumps

79
DT6 TRIPLE VANE PUMPS

2
DT6 TRIPLE VANE PUMPS ORDERING CODE

DT6I- DCC - B - 62/38/70 - 1 - R - 00 - B - 1 - M - 00

Special ports (only DT6DCC/DT6EDC )

Special Features

1:NBR
Seal Class
5:VITON

Design letter

Porting combination (see diagrams)

R: clockwise
Direction of rotation L: counterclockwise

Type of Shaft (see particular pump model)

Flow (see particular pump model)

Bidirectional

Size (DCC, EDC)

Vane pumps “DT6” series

80
DT6 TRIPLE VANE PUMPS - GENERAL CHARACTERISTICS

TRIPLE VANE PUMPS


P1 P2 P3 Front SAE 4 holes flange
Flange Weight
Series Cartridge Theoretical Maximum Cartridge Theoretical Maximum Cartridge Theoretical Maximum Maximum
Standard Kgs Suction Pressure
model displacem. Pressure model displacem. Pressure model displacem. Pressure speed
3
Cm /rev
3
Cm /rev SAE j744c
Cm3/rev S
ISO 3019-1 P1 P2 P3

DT6DCC 014 a 061 47.6 a 190.5 240 003 a 031 10.8 a 100 275 003 a 031 10.8 a 100 275 2500 SAE C 61 4” 1 1/4” 1” 1” ó 3/4”
DT6EDC 042 a 085 132.3 a 269.8 240 014 a 061 47.6 a 190.5 240 003 a 031 10.8 a 100 275 2200 ISO 3019-2 100 4” 1 ½” 1 1/4” 1” ó 3/4”

C - 025,028,031 - 2500 rpm maximum, 028,031 - 210 bar maximum intermitent


D - 042,045,050 - 2200 rpm maximum, 050 - 210 bar maximum intermitent - 061 - 120 bar max intermitente
E - 085 - 2000 rpm max - 90 bar maximum intermitent

TRIPLE VANE PUMPS - PORTING COMBINATION DT6DCC-DT6EDC


00 01 02 03 04 05 06 07
P1-P2-P3 P1-P2-P3 S-P1-P2-P3 P1-P2-P3 P1 P1 P1 P1-S
S S P2
S S P2 P2
P3 P3 P3
S S-P2-P3
08 09 10 11 12 13 14 15
P1-S P1-S P1 P1-P2 P1-P2 P1-P3 P1 P1-P3
P2 P2
S S SS S
P3 P3
P2
P2-P3 P2-P3 S-P3 P2-P3
16 17 18 19 20 21 22 23
S-P1-P2 S-P1-P2 S-P1-P2 S-P1-P3 S-P1-P3 S-P1-P3 P1-P2 P1
P3 P2 P2 P3
P3 S S
P2
P3 P2 P3
24 25 26 27 28 29 30 31
P1 P1 P1 P1-P3 P1-S
P2 P2 P1-S P1-S P1-S
P3 P2 P3
S
P2 P3
P3 P2 P3
S S S-P2 P3 P3 P2 P2
32 33 34 35 36 37 38 39
P1-S P1-S P1-P2 P1-P2 P1-P2 P1-P2
P2 P3 P1-P2 P1-P2
P3
SS P3 SS P3
P2 P3
P3
P3 P3 S S
40 41 42 43 44 45 46 47
P1-P3 P1-P3 P1-P3 P1-P3 P1-P3 P1-P3 P1 P1
P2 P2 P2 P2
SS S P2 S S
P2 S
P3
P2 P2 S S P3
48 49 50 51 52 53 54 55
P1 P1 P1 P1 P1 P1
P3 P3 P3 P1 P1
P2 P2 P3
S S S S
P3 P2 P3
P2 P2 S-P2 S-P2 S-P3 S-P3 P2
56 57 58 59 60 61 62 63
P1 P1 P1 P1 P1 P1
P2 P1 P1
P2 P2 P3
S S P3 S S P3
S S
P3 P3 P2 P3 P2
P2 P2 P3 S P3 S P2

S= Suction port | P1= Shaft end pressure port | P2= Middle pressure port | P3= Cover end pressure port

81
DT6 TRIPLE VANE PUMPS

DT6DCC - OPERATING CHARACTERISTICS


2
SHAFT END SECTION
FLOW
2 SPEED (rpm) PRESSURE (bar) WEIGHT
Mín. Máx. Intermit. Contin. (Kgs.)
Lts/min.at 1000 rpm 48 66 80 90 98 111 120 136 146 158 191
Gal/min.at 1200 rpm 14 20 24 28 31 35 38 42 45 50 61 400 2500* 240 210 24

* See page 41 for further information about speed & pressure.

MIDDLE SECTION
FLOW
2 SPEED (rpm) PRESSURE (bar) WEIGHT
Mín. Máx. Intermit. Contin. (Kgs.)
Lts/min.at 1000 rpm 11 17 21 26 34 37 46 58 64 70 79 89 100
Gal/min.at 1200 rpm 3 5 6 8 10 12 14 17 20 22 25 28 31 400 2800* 275 240* 15

* See page 41 for further information about speed & pressure.

COVER END SECTION


FLOW
2 SPEED (rpm) PRESSURE (bar) WEIGHT
Mín. Máx. Intermit. Contin. (Kgs.)
Lts/min.at 1000 rpm 11 17 21 26 34 37 46 58 64 70 79 89 100
Gal/min.at 1200 rpm 3 5 6 8 10 12 14 17 20 22 25 28 31 400 2800* 275 240* 15

* See page 41 for further information about speed & pressure.

DT6DCC - FLOW & INPUT POWER DIAGRAMS

SHAFT END

See DT6D Single Pumps for flow and input power diagrams (page 44)

MIDDLE BODY
See DT6C Single Pumps for flow and input power diagrams (page 42)

COVER END

See DT6C Single Pumps for flow and input power diagrams (page 42)

82
DT6 TRIPLE VANE PUMPS

TRIPLE PUMPS DT6DCC - DIMENSIONS


212,5
61 55,1

90,5
181
7,9 7,9
2
31,4 38,1
2,3 x 45º 2,3 x 45º

Shaft Code 4 Shaft Code 3


SAE CC Splined shaft SAE C Splined shaft
1-J498b 12/24 d.p. - 1-J498b 12/24 d.p. -
17 Teeth 14 Teeth
Ø 17,5 30º Pressure angle 30º Pressure angle
Mounting Torque 187 Nm

Shaft Torque limits (cc/rev x bar) Alternate Ports


Pump Shaft Code V x P max (P1+P2+P3) Shaft Code V x P max (P1+P2+P3) Orifice Code A B C

TRIPLE VANE PUMPS


DT6DCC 1 43240 3 61200 P3 00* 52,4 26,2 25,4
DT6DCCM 2 66500 4 66500 P3 01* 47,6 22,1 19,0
404 *Add the following numbers at the
83,6 end of the DT6DCC reference
84,4 119,3 138 38,1
12,7 depending your option.
7,9
6,35 Max 49,3
Key 6,35/6,30
101,6

127

Ø 127,00/126,95

Code 00 Code01
Ø 31,75/31,70

P3 1” 3/4”
Ø 34,6 Max
85

2,3 x 45º

1,3 x 45º Shaft Code 1


Mounting torque 69 Nm Mounting torque 187 Nm Keyed no SAE

4 Orifices 3/8-16 UNC x 19.05 4 Orifices 5/8-11 UNC x 30.48


4 Orifices 3/8-16 UNC x 19.05 15,7 89,7
4 Orifices 7/16-11 UNC x 22.09
7,9
B 26,2 77.8 30,2
50,8
Key 9,52/9,47

M10 x 20
130,2

58,7
52,4
A

Ø 38,10/38,05

Ø 64,3

2,3 x 45º

Shaft Code 2
Ø C - Pressure Ø 25,4 - Pressure Ø 101,6- Suction Ø 31,8 - Pressure Keyed SAE CC 83
DT6 TRIPLE VANE PUMPS

DT6EDC - OPERATING CHARACTERISTICS


2
2 SHAFT END SECTION
FLOW
2 SPEED (rpm) PRESSURE (bar) WEIGHT
Mín. Máx. Intermit. Contin. (Kgs.)
Lts/min.at 1000 rpm 132 142 156 165 197 213 227 270
Gal/min.at 1200 rpm 42 45 50 52 62 66 72 85 400 2200* 240 210 44

* See page 41 for further information about speed & pressure.

MIDDLE SECTION
FLOW
2 SPEED (rpm) PRESSURE (bar) WEIGHT
Mín. Máx. Intermit. Contin. (Kgs.)
Lts/min.at 1000 rpm 48 66 80 90 98 111 120 136 146 158 191
Gal/min.at 1200 rpm 14 20 24 28 31 35 38 42 45 50 61 400 2500* 240 210 24
* See page 41 for further information about speed & pressure.

COVER END SECTION


FLOW
2 SPEED (rpm) PRESSURE (bar) WEIGHT
Mín. Máx. Intermit. Contin. (Kgs.)
Lts/min.at 1000 rpm 11 17 21 26 34 37 46 58 64 70 79 89 100
Gal/min.at 1200 rpm 3 5 6 8 10 12 14 17 20 22 25 28 31 400 2800* 275 240* 15

* See page 41 for further information about speed & pressure.

DT6EDC - FLOW & INPUT POWER DIAGRAMS

SHAFT END

See DT6E Single Pumps for flow and input power diagrams (page 46)

MIDDLE BODY
See DT6D Single Pumps for flow and input power diagrams (page 44)

COVER END

See DT6C Single Pumps for flow and input power diagrams (page 42)

84
DT6 TRIPLE VANE PUMPS

TRIPLE PUMPS DT6EDC/DT6EDCM - DIMENSIONS


Ø 22

2
45º

5
31
Alternative ports

Ø
Orifice Code A B C

P3 00* 52,4 26,2 25,4


273

P3 01* 47,6 22,1 19,0

*Add the following numbers at the


end of the T6EDC reference
depending your option.
106

Please, contact TDZ for special shaft


codes not included in this catalogue.
110
273

120 148,4 133,3 42,9 Shaft Code 1

TRIPLE VANE PUMPS


2 x 45º Keyed G45N - ISO 3019-2

9,9
139,7

63,5
115
74,7

101,6

Ø 249,98/249,94
Ø 48,9 Max
M12 x 24

M12 x 20
22 8,9 Code 00 Code 01
120,1 100,7
468 91,9
P3 1” SAE 3/4” SAE
M10 x 19 M12 x 24 M16 x 30 M12 x 30
B 30,2 77,8 35,8
Ø 44,99/45,02
Ø 14,00/13,95
69,9
130,2
58,7

209
A

Mounting Torque 54 Nm Mounting Torque 190 Nm Mounting Torque 300 Nm


Ø 38,1 - Pressure
85
Ø C - Pressure Ø 31,8 - Pressure Ø 101,6 - Suction
86
SPECIAL VANE PUMPS

SPECIAL VANE PUMPS

- CH25 Compact power pack

- Pumps with flow regulating and pressure limiting valves


- Pumps with valves and tank of 1,5 Ltrs. or 1 Lt. with built-in filter
- Pumps with valves and manual flow regulating key
- 1.5 litres and 1 litre oil tanks with built-in filter

These pumps include in a compact set, one BHP2 vane pump, one
pressure limiter valve and one flow regulating pilot valve; being also
possible to add an oil tank with paper filter cartridge.
So, in a very small place and at an economical cost almost all
necessary elements are available for many simple hydraulic circuits.
Flow regulating valve gives constant delivery flow, even with changes
in pump rotation speed and load.

87
88
SPECIAL VANE PUMPS

CH25/PRODUCT INFORMATION

The CH-25 contributes a definitive solution of the problems that appear in the installation of a
hydraulic system, such as the assembly and the design. It is a set formed by a simple o multiple
vane pump, a veried group of valves to be able to make easily tipical schemes, a built-in high
pressure filter and support to be able to be connected a electric standard B5 motor of diverse
powers, all integrated it in an extremely compact equipment. The reason that it mounts a vane
pump must to the requirements of the industry today, then facility and flexibility of handling and
spare parts, high capacity of flow (to 80 GPM), high work pressure (to 270 bar), very high
efficiency (94%), and all it with a highly quiet operation due to its compact design.

SPECIAL VANE PUMPS

89
SPECIAL VANE PUMPS

CH25/MAIN DIMENSIONS

Available pump displacements:


26, 40, 45, 55, 60, 67, 80 and 88 Cm3/rev.
Maximum Pressure: 210 bar.

G06 Pressure control valve mounting side

Tank vertical mounting dimensions


Pressure filter mounting side.

Electrical motor coupling bell acording ISO 4


Stackable mounting bases side

90
SPECIAL VANE PUMPS

CH25/ASSEMBLY SCHEME

Modular elements on CETOP manifold Proportional control of Pressure


and Flow.

Pressure filter on board

SPECIAL VANE PUMPS


Electrohydraulic pressure control
or remote pressure control

Assembly examples

91
SPECIAL VANE PUMPS

B2V SINGLE VANE PUMP WITH VALVE

Valves can be adjustable, made to order, as follows:


- Flow: Up to the limit of the pump cartridge.
- Pressure: 15 to 150 Kgs./cm².

Inlet

Outlet

Torque = 22 Kpm Inlet See shaft types


and measures

DIMENSIONS IN MILLIMETRES
1" = 25.4 millimetres

Continuous line shows those of pumps with outlet port sized to give
as maximum the cartridge rated flow.
Broken line is, for instance, of one pump with hole sized to give as
maximum flow 18 Ltrs. (In this case cartridge rated flow is 15 ltrs. at
1000 rpm.)
Litres/minute

Hexagonal 24

Nº1 Shaft

Nº2 Shaft
Diametral pitch: 16/32
Tooth number: 9

Nº3 Shaft

OUTLET INLET CARTRIDGES


Ltrs./min a 1000 rpm

M12x1,5 M16x1,5 7
8
M14x1,5 M18x1,5
10
M16x1,5 3/4" BSP 12 Port sizes are optional.
3/8" BSP 15
Any combination can be supplied.

92
SPECIAL VANE PUMPS

B2VA & B2VC SINGLE VANE PUMP WITH VALVE, TANK AND FILTER

Valves can be adjustable, made to order, as follows: 2


- Flow: Up to the limit of the pump cartridge.
- Pressure: 15 to 150 Kgs./cm².
Tank includes inside one paper filter cartridge of 25µ

B2VC
(1,5 ltrs)

B2VA
(1 ltr)

SPECIAL VANE PUMPS


Inlet

Outlet

Nº3 Shaft
Nº1 Shaft Nº2 Shaft
Diametral pitch: 16/32
Tooth number: 9

Continuous line shows those of pumps with outlet port sized to give
as maximum the cartridge rated flow.
Broken line is, for instance, of one pump with hole sized to give as OUTLET INLET CARTRIDGES
maximum flow 18 Ltrs. (In this case cartridge rated flow is 12 ltrs. at Ltrs./min a 1000 rpm
1000 rpm.)
M12x1,5 Ø 13 7
8
M14x1,5
10
Litres/minute

M16x1,5 12
3/8" BSP 15

Port sizes are optional. Any combination can be supplied.

93
SPECIAL VANE PUMPS

SINGLE PUMP WITH VALVES AND MANUAL FLOW REGULATOR

TYPES
2 B2VRC: Pump with manual flow & pressure regulating valves
B2VARC: Pump with f. & p. valves and 1 Ltr. tank
B2VCRC: Pump with f. & p. regulating valves and 1.5 Ltrs. tank

Outlet
Aprox.

Delivery flow may be varied with this regulator in any of the


a.m. B2V pumps. Flow keeps constant even with changes
in pump speed and load.

It can optionally
be served with
adjustable ring.

The complete regulator kit can be assembled in any pump


with flow regulating valve and outlet of M16 x 1,5.
Order ref.: BV.02401

94
SPECIAL VANE PUMPS

FR01000 (1.5 LTRS) AND FR05050 (1 LTR) TANK TYPES WITH PAPER FILTER

WITHOUT SUPPORT 2
DIMENSIONS IN MILLIMETRES 1" = 25.4 millimetres

Hexagonal

Oultet
Hexagonal
Inlet Minimun thickness for the

SPECIAL VANE PUMPS


Adjustable support plate: 4 mm.

Tank includes one inlet paper filter cartridge of 25µ

95
SPECIAL VANE PUMPS

FR04000 (1.5 LTRS) AND Fr05000 (1 LTR) TANK TYPES WITH PAPER FILTER

2 WITH ALUMINIUM SUPPORT

Hexagonal

Inlet

Oultet

Hexagonal

Inlet

Hexagonal
Oultet

Tank includes one inlet paper filter cartridge of 25µ

96
MHP & MD4C VANE MOTORS

VANE MOTORS
MHP & MD4C

97
MHP VANE MOTORS

VANE MOTORS CODE

F3 MHP 2 10 D 1 A
1 2 3 4 5 6 7

1 - "F3" means special seals for fire-resistant fluids. Omit if not required

2 - Motor Type:

MHP = 10 vanes motor, mobile and industrial use, metric threads.

3 - Motor Model:
Models 2

4 - Flow: In litres per minute at 1000 rpm and 7 bar.

5 - D = Right-hand direction of rotation, (Clockwise)


Y = Left-hand direction of rotatio, (Counterclockwise)
(To check the direction of rotation view from the shaft end).

6 - Shaft type: See on each motor model information.

7 - Oulet position (Viewed from shaft):


A: Outlet in line with inlet
B: 90° clockwise from inlet
C: 180° from inlet
D: 90º counterclockwise from inlet

98
MHP VANE MOTORS

MHP VANE MOTORS

FLOW SPEED (rpm) (3) PRES (BAR) CONNECTION WEIGHT


Lts.at 1000 rpm 7 8 10 12 15 Mín. Max. Contin Máx. Intermit. Contin. Interm. Entrada Salida
2 (Kgs.)
Gal. At 1200 rpm 2,2 2,5 3,2 3,8 4,7
Torque (N.m) (1) 11 13 16 19 24 300 3000 3500 150 175 1/2" BSP 1/2" BSP 3,6
No.m Powerl(CV)(2) 1.5 1.7 2.1 2.5 3.1

(1) Theoretical Torque in N.m at 100 Bar.


(2) Nominal Power in H.P. at 100 Bar and 1000 r.p.m.
(3) For pressures lower of 100 bar, the maximum speed can increase until 20%
Flow and power diagrams, see corresponding pump

97
20
61
2,2 Kpm

58
Ø10,2

40

5 93

112

11
Inlet 3/4"
Outlet 1/2" BSP BSP

80 50 f7

MOTORS

Nº1 Shaft Nº2 Shaft Nº3 Shaft

Diametral pitch: 16/32

Tooth number: 9

Enquire about other types of shafts

99
MD4C VANE MOTORS

MD4C - ORDERING CODE & OPERATING CHARACTERISTICS

2
MD4C 075 1 N 00 C 1 02 ..

Series external drain Modification


Port connections
Nominal flow (nominal torque) 01 = Threaded Port
024 (0,39 Nm/bar) 1” 5/16 UNF
027 (0,45 Nm/bar) 9/16”-18 UNF Drain
031 (0,55 Nm/bar) 02 = 4 Bolt Flange
043 (0,74 Nm/bar) 3/8’’-16 UNC Threaded
055 (0,93 Nm/bar) 9/16”-18 UNF Drain
067 (1,13 Nm/bar) 03 = Threaded Port 3/4’’ BSP
075 (1,27 Nm/bar) 3/8” BSP Drain
100 (1,56 Nm/bar) 04 = 4 Bolt Flange
3/8-16 UNC Threaded
Type of shaft 3/8‘’ BSP Drain
1= Keyed (SAE B) M4 = 4 Bolt Flange
2= Keyed (no SAE) Metric Threaded M10x20
3= Splined (SAE B) 3/8’’ BSP Drain
9= Special (non SAE)
Seal Class
Rotation 1 = NBR 5= Viton
N = Bi-direccional Desing letter
View from shaft end: Porting combination
CW Rotation: A= INLET
INTERNAL LEAKAGE 01 = Side ports (right/left)
B= OUTLET 36 02 = Side ports (up/down)

BA
10 cSt
CCW Rotation: A= OUTLET 32
24 cSt DRAIN
B= INLET
Internal leakage (l/min)

28
24 B
20
16
A
DRAIN
12 01 02
8
4
0
0 35 100 140 175 P ressure (bar)

OPERATING CHARATERISTICS (24 cSt)

To r q u e T Poweroutput
Volumetric I n p u t f l o w a t n = 2000 R PM At n = 2000 R P M At n = 2000 R P M
M o del displacement (Vi)
Te órico a 175 bar p a 175 bar p a 175 bar p

cc/rev l/m in l/m in Nm kW


M D 4 C - 02 4 24.4 49.0 63.0 60.5 12.7
M D 4 C - 02 7 28.2 56.0 70.0 70.0 14.7
M D 4 C - 03 1 34.5 69.0 83.0 86.8 18.0
M D 4 C - 04 3 45.5 93.0 107.0 120.0 25.1
M D 4 C - 05 5 58.8 118.0 132.0 149.0 31.2
M D 4 C - 06 7 71.1 142.0 156.0 170.0 35.6
M D 4 C - 07 5 80.1 160.0 174.0 198.0 41.5
M D 4 C - 10 0 100.0 200 217.5 247.5 51.2

100
MD4C VANE MOTORS

DIMENSIONS, SHAFTS & PORT CONNECTIONS - MD4C

PORT CONNECTIONS 2

3/8" 16 UNC 19 DEEP - 8 HOLES


(M10 X 20 DEEP - METRIC VERSION)

DRAIN SAE 6
Mounting (9/16" - 18 UNF)
torque OR 3/8" BSPP

A B (2 places)

(15/16" UNF 19 Deep)


(2 Places)
188 (SAE & BSP Threaded Ports)

A B

SAE THREADED PORTS

3/4" BSP 17 DEEP


(2 Places)

A B

BSP THREADED PORTS

Weight : 15,4 Kg

MOTORS
SHAFT TYPE

SAE B splined shaft


Class 1 J498b
16/32 d.p. - 13 teeth
30º pressure angle
flat root side fit

SHAFT CODE 1 SHAFT CODE 2 SHAFT CODE 3 SHAFT CODE 9

Enquire about other types of shafts

101
MD4C VANE MOTORS

PERFORMANCE CURVES - OIL VISCOSITY : 24 CST (45º) - MD4C

100
2
MD4C 30

024 75
25
Torque T (Nm)

T=175 bar

Power (kW.)
20
T=140 bar P=175 bar
50 15
P=140 bar
T=105 bar
P=105 bar
10
25 T=70 bar P=70 bar
T=35 bar 5
P=35 bar
0 0
0 100 500 1000 1500 2000 2500 3000 3600
Velocidad (RPM)
100
30
MD4C
027 T=175 bar 25
75
20
Torque T (Nm)

T=140 bar P=175 bar

Power (kW.)
50 P=140 bar
T=105 bar 15
P=105 bar
T=70 bar 10
P=70 bar
25
T=35 bar 5
P=35 bar

0 0
0 100 500 1000 1500 2000 2500 3000 3600
Velocidad (RPM)
100 35
MD4C T=175 bar
30
031
75 T=140 bar 25

Power (kW.)
Torque T (Nm)

P=175 bar P=140 bar


T=105 bar 20
P=105 bar
50
15
T=70 bar
P=70 bar 10
25
T=35 bar P=35 bar 5

0 0
0 100 500 1000 1500 2000 2500 3000 3600
Velocidad (RPM)
50
MD4C 150
T=175 bar 45
043 125 40
35
100 T=140 bar
Power (kW.)
Torque T (Nm)

P=175 bar 30
P=140 bar
75 T=105 bar 25
P=105 bar
20
50 T=70 bar P=70 bar 15
10
25 T=35 bar P=35 bar
5
0 0
0 100 500 1000 1500 2000 2500 3000 3600
Velocidad (RPM)
102
MD4C VANE MOTORS

PERFORMANCE CURVES - OIL VISCOSITY : 24 CST (45º) - MD4C

MD4C
175 2
60
T=175 bar 55
150
055 50
125
T=140 bar 45
P=175 bar
40
Torque T (Nm)

Power (kW.)
100 T=105 bar P=140 bar 35
P=105 bar 30
75 25
T=70 bar
P=70 bar 20
50
15
T=35 bar
25 P=35 bar 10
5
0 0
0 100 500 1000 1500 2000 2500 3000 3600
Velocidad (RPM)
225 60
MD4C 200 55
T=175 bar
067 50
175 P=175 bar
P=140 bar 45
150 T=140 bar
40
Torque T (Nm)

Power (kW.)
P=105 bar
125 35
T=105 bar
30
100
25
75 T=70 bar
P=70 bar 20
50 15
T=35 bar 10
25 P=35 bar
5
0 0
0 100 500 1000 1500 2000 2500 3000 3600
Velocidad (RPM)

225 T=175 bar 60


MD4C 200 55
P=175 bar
075 T=140 bar 50
175
45
P=140 bar
150 40
Torque T (Nm)

T=105 bar P=105 bar Power (kW.)


125 35
30
100
T=70 bar 25

MOTORS
75 20
P=70 bar 15
50 T=35 bar
P=35 bar 10
25
5
0 0
0 100 500 1000 1500 2000 2500 3000 3600
Velocidad (RPM)

103
104
V* VANE PUMPS - INSTRUCTIONS FOR USE & REPAIRS

INSTRUCTIONS FOR
USE AND REPAIRS
Cartridge identification, change of rotation, guidelines for repairs.
V* series

105
V* VANE PUMPS - INSTRUCTIONS FOR USE & REPAIRS

IDENTIFICATION

Due to the difficulty in finding out spare cartridge references, either for the loss of the
pump feature plate, or for the lack of the machine spare part catalogue, it is most
convenient to include some sheets to identify the sample accurately and to give some
advice for a correct assembly.

To identify properly cartridge and pump, use the 3 following pages as follows:

- DIMENSIONS AND FLOW


Find out pump type and flow in the dimensions chart, look at the figure engraved on
the ring as shown (gallons/min. at 1200 rpm).

- SUPPORT BUSHING AND SHAFT ROTATION


Locate support bushing to know whether the cartridge belongs to a single or double
pump. On this page there are also some clues to identify shaft rotation.

106
V* VANE PUMPS - INSTRUCTIONS FOR USE & REPAIRS

IDENTIFICATION

DIMENSIONS AND FLOW

B C

INSTRUCTIONS FOR USE AND REPAIRS (V* SERIES)


Outlet plate
Inlet plate
Ring or cam ring

DIMENSIONS PUMP TYPE


I n mm. 20V 25V 30V 35V 45V
A 81,8 99,5 110,5 118,4 140,5

B 82,6 96,8 96,8 114,25 133,3

C 47,15 52,15 52,15 72,15 80,15


WEIGHT 2,300 3,800 4,100 6,400 10,200
aprox. in Kg.

2 8 24 21 42
5 12 28 25 47
FLOW 8 14 30 50
9 17 35 57
in Gal. at 1.200 rpm 11 19 60
38
12 21 45 67
14 24 75
27

Flow is engraved in this area

107
V* VANE PUMPS - INSTRUCTIONS FOR USE & REPAIRS

IDENTIFICATION

PUMP ROTATION

To determine pump rotation look at it from the shaft end side. If clockwise it is right hand
rotation, on the contrary, it is left hand rotation.

When taking out cartridge and putting it on to the outlet plate take into account that
rotation is seen the other way round; anyway, an arrow engraved in the ring or cam ring shows
the real turning sense. (See pictures.)

Support Bushing
Always mounted on the
inlet plate.
All single pumps have it.

Pump rotation is viewed from the


shaft end side.

LEFT RIGHT

RIGHT

LEFT

108
V* VANE PUMPS - INSTRUCTIONS FOR USE & REPAIRS

IDENTIFICATION

2
PUMP ROTATION

Support Bushing
Shaft End Cartridge Double pumps only wear it on the shaft
end cartridge (Cover end cartridges do not have it).

Cover End Cartridge

INSTRUCTIONS FOR USE AND REPAIRS (V* SERIES)


Double pump special feature is that their 2 cartridges are opposite each other, therefore when putting them on
the outlet plate, they will apparently have opposite turning sense.
Anyway, the arrow in the ring shows the correct rotation. (Pump and cover end cartridge rotation always
coincide.)

LEFT
hand rotation Pump LEFT
LEFT

Shaft end cartridge Cover end cartridge

RIGHT
hand rotation Pump RIGHT
RIGHT

109
V* VANE PUMPS - INSTRUCTIONS FOR USE & REPAIRS

RECOMMENDATIONS FOR PUMP AND CARTRIDGE MANIPULATIONS

Since this is a high precision kit (mechanized in tolerances within thousandth of millimeter), any abrasive
impurity can damage it in a few minutes or damage it to shorten its performance, before disassembling
it is necessary that working place, tools and worker handsare completely clean and neat.

Please avoid any blow, however insignificant, taking special care with all edge sides, ring seat points
and inlet and outlet plates.

All these preventive measures taken, proceed as follows:

1º Lean the cartridge, holding it tightly, at the work bench on the outlet plate. Loosen the 2 screws which
fix the kit, take them out as well as the pins (if there are any).
Take out inlet plate shifting it laterally, as due to the protective oil it may be gummed up. Place it at the
bench on a clean paper, white preferably.

2º Do the same with vanes, rotor and ring.


Place the rotor, once disassembled, onto the outlet plate with arrow showing the required turning
sense (see detail in the circle, fig. 3), afterwards, put inserts into vanes (fig. 4), and finally, introduce
them in the slots, well at the bottom, with vane closing edge in forward rotation, as arrow shows in
the corresponding picture.

3º Be sure there is no small dirty particles on the leaning surface, put ring on to the outlet plate, placing
it in the required turning sense. Make chamfer edge coincide, in which flow and arrow are engraved,
with inlet or admission port.

4º Set inlet plate, pins and the 2 screws as shown in the pictures, taking into account that the lattes must
be in opposite position to the ones they had before disassembling. (To do so, just turn ring, rotor and
vanes 180°). Fasten the screws moderately and dip the whole cartridge kit into clean hydraulic oil for a
while. After these steps it is ready to be assembled.

Please pay good attention to the cartridge and pump rotation, as they do not always coincide.
Be very careful to identify them properly. (See previous pages.)

110
V* VANE PUMPS - INSTRUCTIONS FOR USE & REPAIRS

CHANGE OF CARTRIDGE ROTATION

RIGHT HAND LEFT HAND


rotation rotation
(clockwise) (counterclockwise)

A B

Fig. 1

A B

Outlet plate

INSTRUCTIONS FOR USE AND REPAIRS (V* SERIES)


A B

Fig. 2

A B

A B

Fig. 3

A B

Fig. 4 Arrow engraved on the Fig. 4


Rotation rotor outside diameter. Rotation

180º 180º

111
V* VANE PUMPS - INSTRUCTIONS FOR USE & REPAIRS

RECOMMENDATIONS FOR PUMP AND CARTRIDGE REPAIRS

CARTRIDGE REPLACEMENT

To successfully replace cartridge, be sure to follow these warnings:

1º - Check if due to use there is tread on the cartridge seat


zone (dark area in the picture).
If so, deepness must not be higher than 0,01 mm. (This could
be observed even with a fingernail), being most convenient
in such cases grinding or changing the pump body with this
fault, as otherwise noise and performance values will not be
the right ones. (In case you can not grind the seat, TDZ has
-avaible for sale- a simple machine specially designed for
this purpose).

2º - Look at the cartridge to be replaced, if wear is normal


just change oil in tank circuit and change or clean filters.

3º - Should the used cartridge shows seizure in rotor, outlet & inlet plates, disassemble the
pump completely. Check that the key is in good condition (it could be cut out). Then, put the
shaft between points to make sure it is not twisted or crooked. Change it in case of any fault.
Take all the oil out of the circuit and other parts. Clean the tank carefully. If there is available
any used cartridge mount it and start the machine for at least 15 minutes, driving all controls.
To do so, spend the least possible amount of oil, since it will have to be replaced after this
operation, although it could be reused again, after being filtrated in a filter no bigger than 5
microns, as it still keeps additives).
Replace or clean all filters, mount the new cartridge and fill the tank to the level with new oil.

CARTRIDGE REPAIRS
MINIMAL CLEARANCE BETWEEN CAM RING AND ROTOR

MODEL Inches Millimetres

20V 0.0007 0,018


25V 0.0012 0,030
30V 0.0014 0,035
35V 0.0015 0,038
45V 0.0016 0,040

* Vane length must be from 0,005 to 0,010 mm. (0,0002 to 0,0004


inches) less than rotor thickness.

To rebuild cartridges it is necessary to use grinding & lapping machines, as well


as measurement tools able to work in microns.

112
V* VANE PUMPS - INSTRUCTIONS FOR USE & REPAIRS

RECOMMENDATIONS FOR PUMP AND CARTRIDGE REPAIRS

TIGHTEN TORQUE FOR PUMP SCREWS

Reference Tighten torque in Kp.m.

20V 6,5

SINGLE 25V 10,5


PUMPS
35V 22,5

45V 35

INSTRUCTIONS FOR USE AND REPAIRS (V* SERIES)


Inletbody Cover

25-20V 10,5 6,5

35-20V 22,5 6,5


DOUBLE
PUMPS 35-25V 22,5 10,5

45-20V 35 6,5

45-25V 35 10,5

45-35V 35

Rear flange mountings of the V**T* thru drive pumps.

Tighten torque for pump screws: 6,5 Kp.m.

Tighten the screws, with a torque no bigger 1 3


than 0,5 to 1 Kp.m before beginning the last
or final tighten.
Follow the order shown in the picture.
4 2

113
114
DT6 VANE PUMPS - INSTRUCTIONS FOR USE & REPAIRS

INSTRUCTIONS FOR
USE AND REPAIRS
Cartridge identification, change of rotation, guidelines for repairs.
DT6 series

115
DT6 VANE PUMPS - INSTRUCTIONS FOR USE & REPAIRS

INSTRUCTIONS FOR USE AND REPAIRS

PRIMING AT STARTING

Before starting the operation of TDZ hydraulics vane pumps, the following aspects should be always carefully
checked:

· Speed range, pressure, temperature, fluid characteristics and pump rotation.


· Inlet conditions considering the application.
· Coupling must be chosen to minimize shaft loads, (misalignment, weight, etc..)
· Shaft must support operating torque.
· Filtration should be adequate for the lowest possible contamination level.

At first, start operation at lowest possible speed and pressure until regular operating fluid temperature is reached. If
a relief valve is used at the outlet, it should be backed off to minimize return pressure.
An air bleed off should be provided to purging of system air.

MODIFICATION OF INLET OUTLET PORTS POSITION

Vane pumps may present different external configurations depending on the inlet port position (located in the back
cover) in relation to the outlet port (located at the front flange or shaft end).

The inlet port may be in line with the outlet port, 90º to the right, 90º to the left or totally opposite to the outlet port
(180º).

These are the following steps that should be followed in order to modify the porting positions:

· Fix the pump in a working bench and loosen the 4 bolts that fix the back cover with the front body, (flange side
or shaft end part).
· Do not remove the 4 bolts totally. Remove approximately half of their total length them from the pump body.
· Separate the back cover from the front body by only 1mm 2mm maximum, turning the cover slightly to the right
and to the left, pushing it outwards.
· Using a sufficiently-long metal bar.

116
DT6 VANE PUMPS - INSTRUCTIONS FOR USE & REPAIRS

CHANGING THE POSITION OF THE PUMP PORTS

Vane pumps have a different external configuration, depending on the position of the suction flange (located on
the pump cover) in relation to the pressure flange (located on the coupling flange or shaft side).

The suction flange may be in line with the pressure flange, (o°), 90° to the right, 90° to the left or totally opposite it
(180º in relation to the pressure flange).
The steps to modify the position of the suction flange in relation to the pressure flange are as follows:

1– Secure the pump to a workbench and


loosen the four bolts joining the pump
cover to the front body (or shaft-side
body).

2- Do not fully remove the bolts. Remove


approximately half their total length from
the pump body.

INSTRUCTIONS FOR USE AND REPAIRS (DT6 SERIES)


3- Remove the front body cover just 1
mm - 2mm, (maximum) by slightly turning
the cover and pushing it outwards.

4- Using a sufficiently long, resistant


metal bar, support it obliquely on two
diagonally opposite screws and lever,
making the cover turn until the suction
flange is in one of the four aforementioned
positions. TURN

5- Readjust the cover and the 4 bolts with


the appropriate torque. Make sure that no
particles of paint or other material are
between the body and the cover and that
the o-ring housed between these two
parts is not pinched when tightened.

117
DT6 VANE PUMPS - INSTRUCTIONS FOR USE & REPAIRS

CHANGE OF CARTRIDGE ROTATION

The cartridges on this type of pump available worldwide can be unidirectional or bidirectional. Rotation on
unidirectional cartridges cannot be modified, except where the cartridge pressure plates are replaced for others
with an opposite turning direction or for bidirectional plates.

TDZ cartridges are bidirectional. This means that rotation can be modified by means of a simple operation using
exactly the same cartridge components that are to be modified.

The steps to follow are as indicated:

1.- Remove the 2 set screws from the cartridge.

2.- Remove the cartridge suction cover. Of the two cartridge covers, the suction cover is the flattest and may be
fitted with a bronze bearing, depending on the position of the cartridge on the pump (P1, P2 or P3).
Next to the cover is a position pin that should also be removed.

3.- Remove the cam ring or stator and turn 180º so that side "A" of the stator that was previously in contact with
the surface of the suction cover is now touching the pressure cover and side “B” of the stator that was previously
in contact with the pressure cover is now touching the suction cover.

4.- Change the positioning pin on the pressure cover from hole "A" to hole "B" and re-insert the stator so that the
stator hole matches the new position of the pin.

5.- Also change the position pin on the suction cover and readjust the cover using the two screws. Turn the rotor
and the blades manually before tightening the screws.

Attentions: The screws are basically for alignment purposes. They must not be too tight. If the three parts of the
cartridge (stator, suction cover and pressure cover) are not perfectly concentric, it will be impossible to insert the
cartridge into the pump housing.

In this case, loosen the screws slightly and insert the entire cartridge into the body of the pump. When it is fully
inserted is when the cartridge parts are fully aligned and the screws can be readjusted.

118
NOTES

119
NOTES

120

You might also like