Use of Syrian Natural Zeolite For Heavy Metals

Removal of Heavy Metals from Industrial Waste Water
The presence of accumulated heavy metals in the environment constitutes a serious threat
to human life and the environment because of their toxicity. Many toxic heavy metals have been
discharged into the environment as industrial wastes resulted from crude oil desalter annexed to
oil refinery which is the major source for highly toxic industrial wastewater. Due to high deposit
of Zeolite in nature, and to its low cost, strong adsorption capacity, it has recently drew attention
to be used in the treatment of industrial wastewater. Wastewater treatment in desalter essentially
entails ion exchange reaction by natural Zeolite which has a special structure enable to displace
exchange cations (Mg+,K+,Ca+2, Na+) by heavy metal cations such as Pb+2, V+5, Zn+2, Fe+2, and
Ni+2. The safety of using natural Zeolite is attributed to the non- toxicity of its metals that
displace unfavorable toxic heavy metals from wastewater in the desalter. In the present study
natural Zeolite was tested as an efficient adsorbent for the removal of ions of Pb+2,Zn+2, V+5,Ni+2
from desalter wastewater.
Removal of cadmium and copper from Aqueous Solution
The major industrial sources impact the environment as a result of producing heavy
metals. The existence of heavy metals in wastewater due to many manufacturing processes is a
legalized problem worldwide. Zeolites are aluminosilicate minerals of alkali or alkaline earth
metal which contains crystal water. Zeolites consist of three-dimensional networks of aluminate
and silicone dioxide tetrahedral linked by partnership of all oxygen atoms. For wastewater
treatment, the most important properties of natural zeolite are cation exchange capacity and ion
selectivity. NJ zeolites have been used to eliminate different heavy metals ions from prepared
synthetic solution.
Modification with chemical and Apparatus
Samples of Syrian rocks containing natural zeolite in southern Syria was studied and X
ray diffraction of zeolite sample was measured using X-ray crystallographer. The sample
contains a mixture of phillipsite and chabazite as well as some additional rocky matrices such as
Hematite, Diopside, Smectite. Size of adsorbent particle was determined using the grain size
distribution analysis and the samples were shaken using mechanical shakers for 15 minutes
needed to complete the separation process, the interval of particles diameters of (NZ) was (0.5-
1mm). pH meter and electric mixer were also used.
Modification with chemical and adsorption studies

The bulk sample was washed by distilled water to eliminate most of the surface
dust. Then the sample was crushed and sieved into two different grain sizes (less than 0.4 mm
and 0.4–4 mm). The experiments were performed with grain size distribution less than 0.4 mm in
diameter. Their distribution was measured using laser diffraction instrument (see Fig. 1). X-ray
diffraction was obtained before and after treatment with sodium chloride. Cadmium and copper
nitrate which have been diluted in distilled water are used throughout the experiments. The
chemicals and reagent were supplied from Merck (Germany) and of analytical grade using
deionized water. The ion exchange process on NJ zeolite was accomplished using the batch
method.
Removal of cadmium and copper
1. Effect of metal concentration
To find the optimum concentration, experimental studies were carried out for a wide
range of metal concentrations between 100 and 600 mg/L. The capability of sorption process was
found to be stable and reached a maximum value at concentration 100 mg/L. This is because the
surface where the adsorption occurs reaches its maximum uptake, i.e. no more metal ions can be
adsorbed. The percentage of Cd and Cu removal decreases by increasing initial metal
concentration. This result pointed out that with increasing metal concentration less favorable
spaces become involved in the aqueous solution.
2. Effect of NJ zeolite volume
The amount of zeolite required for quantitative removal of cadmium and copper from an
initial metal concentration 7 mg/L was found to be 30 mg. The adsorption percentage increased
with zeolite mass in case of both cadmium and copper and when the adsorbent reaches beyond
30 mg became steady. The adsorption percentage was found to be 46, 15.5 % in the case of
cadmium and copper, respectively, for identical zeolite dose (1 mg). It is clear that the uptake
efficiency of cadmium and copper increases with the concentration of NJ zeolite. The reason for
this may be the surface area of the zeolite at higher mass concentration of zeolite is more
available.
3. Effect of contact time
It is clear that the contact time needed to reach the maximum removal of metal by NJ
zeolite was dependent on the type of heavy metal. From the economic system point of view, the
role of the equilibrium time assessment is very important especially in many wastewater
treatment applications. The equilibrium adsorption was attained through 20 min for both
cadmium and copper metal and the equilibrium adsorption were determined at 80 and 68 mg/g.
Removal of Heavy Metals
1. Equilibrium time
It's obvious from Fig 2 that adsorption occurred at two stages while the first stage is
instant the second one is slower then it becomes at steady speed until the equilibrium is
attained after 4-6 hours. Thus, the chosen time required for all trials is 6 hours.
Fig 2. Equilibrium time for V+5, Zn+2, Pb+2 &Ni+2 at experimental conditions (CO= 300 ppm
،pH = 6، m=0.5gr ،V=50ml ،0.5-1mm)
2. Effect of adsorbent particle size

It's noticed from figure 3 that increasing the external surface area by reducing the adsorbent
particle size, results in an increase in the number of available sites for metal uptake.
Moreover, smaller particle sizes result in the shortening of the diffusion distance that
heavy metals have to travel in order to get to an adsorption site, hence a faster rate of
reaction. It's also noticed that Vanadium revealed the greatest affinity>90% for most of
used sizes of particles while Nickel revealed the lowest affinity (70-85%).
Fig 3. Adsorbent particle size affecting on the removal of V+5, Zn+2, Pb+2, &Ni+2 from the
solution (C0= 100 ppm ،pH = 6، m=0.5gr ،V=50ml ، T=6h)
3. Effect of competing ions
Wastewater from desalting unit contains various metal ions with influence on potentiality
of adsorbent to treat wastewater in competition for exchange sites and within adsorbent.
Confirmation trials were conducted for the influence of competitive ions on individual
adsorption of each Pb+2, Zn+2, Ni+2, andV+5. Fig 4 implies comparison between heavy
metals ions adsorption from mono and multi component solutes using natural Zeolites. So
as a result it's been found that Nickel adsorption decreased due to competivity, while
other metal ions adsorption were not influenced, that is adsorption capacity of these ions
from single component solutions in comparison to multi component ones and at rate
ranged 1-3% and 10% higher than nickel's. The difference can be attributed to the
adsorptional selectivity of Zeolite specific sites to which each metal ion is adsorbed in
different ways.
Fig 4: Comparison of the adsorption capacity of natural zeolite for V+5, Pb+2, Zn+2 &Ni+2
from single and multi – component solutions.
4. Effect of Hardness
Since desalting wastewater contains high concentrations of Calcium ions, it is considered
hard water and majorly affect the removal of heavy metals from wastewater due to
competing metal ions on exchange site of zeolite structure on one hand and to forming
surface complexes of heavy metals ions bonded to surface on the other hand. Thus heavy
metals removal from water is impeded as shown in Fig 5. It was noticed that the increase
of Calcium ions concentration led to decrease in removal rate of Ni and Zn from 84.6%,
86.8% to 70.61%, 71.22% respectively, while both Pb+2 and V+5 were not influenced by
Calcium ions so that removal rate decreased from 97.2% to 95.22% at high
concentrations of Calcium with potential exposure which led to increasing adsorption of
Calcium in comparison with Pb ions. more over, hydration energy significantly effect on
equivalent ions. i.e. the higher hydration energy the lower competivity of ion is. Thus,
natural zeolite is very efficient in the removal of ions whether in presence or absence of
water hardness agents.
Removal of Heavy Metals

There are many factors that affect the general reaction rate of adsorption process using
natural zeolite. i.e. contact time, initial concentration of solution, size of adsorbent
particles, and hardness. The optimal removal rate occurs after 6hours of contact time,
when using adsorbent particles of small size. We found that the studied zeolite has
adsorption locations on its surface special for every metal. Each metal react with the
corresponding adsorption location with different adsorption forms. Natural zeolite is
highly efficient in the removal of the studied heavy metal ions from the solution
regardless the presence of hardness.
Removal of cadmium and copper

The adsorption capacity of cadmium and copper using NJ zeolite has been experimentally
investigated. It was concluded that metal bulk concentration, adsorption time and mass of
adsorbent, are an important factors that affect the adsorption process. These parameters
had a considerable trace on the uptake of cadmium and copper metal using NJ zeolite.
Cadmium and copper adsorption from aqueous solution using NJ zeolite was well
demonstrated with the second-order kinetic model. The experimental adsorption data
were better adequate to the second-order model than to the first-order model. As a result
of this study, the NJ zeolite for the removal of cadmium and copper using a batch
adsorption technique has inherent advantages.

Use of Syrian Natural Zeolite For Heavy Metals

Uploaded by

Copyright:

Available Formats

Use of Syrian Natural Zeolite For Heavy Metals

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Use of Syrian Natural Zeolite For Heavy Metals

Uploaded by

Copyright:

Available Formats

Removal of Heavy Metals from Industrial Waste Water

Removal of cadmium and copper from Aqueous Solution

Modification with chemical and adsorption studies

2. Effect of adsorbent particle size

Removal of Heavy Metals

Removal of cadmium and copper

You might also like