Here you go: 1- 100uF 35v electrolytic capacitor, 1- transistor TIP-31C

Other transistors you can use and their crosses:

TIP3055 = ECG 392 = 276-2020(Radio Shack)
TIP31C = ECG 291 = 276-2020 (Radio Shack)
TIP120 = ECG 261 = 276-2068 (Radio Shack)

DON'T BOTHER buying the "SUPER-TALK" kits. Make your own!! +

Here are all the VR's for the DX88HL:

1.VR 1...AM/FM S-Meter

2.VR 2...SSB S-Meter
3.VR 3...SSB Squelch Range
4.VR 4...AM/FM Squelch Range
5.VR 5...FM Deviation
6.VR 7...SSB Carrier Balance
7.VR 8...RF Meter
8.VR10...Final Bias
9.VR11...Driver Bias
10.VR12...SSB ALC
11.VR13...AM/FM High Power
12.VR14...AM Modulation
13.VR16...AM/FM Low Power
14.VR20...Final Bias
15.VR21...TX Offset

Galaxy Radios

Galaxy 44V

Channel Expansion

1) Open up your radio.

2) Find the small circuit board on the left of the radio.
3) Cut the green wire and tape it off.
4) There is an unplugged connector by this board..plug it in.
5) Near the front of the radio there is a connector marked +10K. Reconnect the plug
to the board.
6) That's it.!You now have 8 bands of 40 channels.25.165-28.755.

Tweak & Peak

Audio Limiter - R249

AM Power - VR13

Galaxy 55V
Tweak & Peak

Audio Limiter - TR53

AM Power - VR13

Galaxy 66V

Channel Expansion

1) Open up your radio.

2) Find the small circuit board on the left of the radio.
3) Cut the green wire and tape it off.
4) There is an unplugged connector by this board..plug it in.
5) Reconnect the plug to the board.
6) That's it. You now have 8 bands, Channels 25.165-28.755.

Tweak & Peak

Audio Limiter - TR53

AM Power - VR13

Galaxy 99V

Tweak & Peak

Audio Limiter - TR53

AM Power - VR13

Wondering about the "UNCLE MOD

SUPERSTAR 1700, 3600, 3900

MODULATION: VR14 or cut R249

AM POWER: VR13
SSB POWER: VR12

POWER TWEAK:
1. Remove TR32
2. Replace R174 (10k) with a 1 K
3. Replace R187 (10k) with a 1 K

CLARIFIER:
1. Find the GREEN WIRE located at point 54 and UNSOLDER it.
2. Resolder this GREEN WIRE to POINT 14 (8.7 V) or to TR 41 collector.
3. Find the YELLOW WIRE on the clarifier control and UNSOLDER it. Insulate the cut
end. This wire is no longer used.
4. Find D75 (located near POINT 53 and VR15) and lift one end.
5. Find R135 (33k) and lift one end.
6. Double check all work for shorts.

NO EXPLOSION? Then you should be able to track on TX and RX!

CHANNELS:
1. Locate pins #12 and #13 on IC7 (MC14008BCP chip).
2. Using a SPST toggle switch, wire as follows:
Center of toggle switch goes to pin #13
The other goes to pin #12

Your channels should work with your band selector on "D" band.

It should be able to go from 28.300 Mhz. to 28.500 Mhz.ULATOR" ??? Here is what
another reader wrote:Super Star 3900 Gold and Cobra 148GTLX Gold

(These 2 radios are the same except for the name)

VR1 - AM/FM S METER ADJUST

VR2 - SSB/CW S METER ADJUST
VR3 - SSB SQUELCH RANGE
VR4 - AM SQUELCH RANGE
VR5 - FM DEVIATION ADJUST
VR7 - CARRIER BALANCE ADJUST
VR8 - RF METER ADJUST
VR10 - FINAL BIAS ADJUST
VR11 - DRIVER BIAS ADJUST
VR12 - ALC ADJUST
VR13 - AM POWER ADJUST
VR14 - AMC
VR16 - CW MON ADJUST
VR21 - Tx FREQUENCY ADJUST
TR32 - IS THE AMC LIMITER

"I don't recommend removing TR32 as it disables VR12 ALC, SSB power will be at full
blast.
Instead clip or remove R249. This only disables AMC not ALC.
Tune L40, L43, L44, and L33 for maximum forward swing on wattmeter.
Adjust AM power for no more than 5 watts dead-key - if running a linear amp set at
3 watts dead-key.
Adjust ALC for no more than 20 - 25 watts PEP on SSB.
For Talkback remove D80."

SuperStar 3900

+ 10 KHz Jump Switch

1)Get a SPST switch and mount it in the radio.

2)Find IC 6 & 7 by the PLL chip. You will see J68 and J 69
3)Solder a wire from one side of the switch to J68.
4)Solder a wire from the other side of the switch to J69.
5)That's it .Flip the switch to jump up one channel.

Open Clarifier

1)Find D75 and R135 and cut one end of them.

2)On the back of the clarifier knob follow the green wire to the PC board. Cut this
wire from the PC board.
3)Now Solder this wire to a constant 8VDC source, like the collector of TR41.
4)Take the yellow wire and cut it from the knob. Tape this wire it is not needed.
4)This should make the radio TX/RX on the same frequency.

10 Meter Mod

1)Find IC7 ny the PLL chip.

2)Get a SPST switch and mount it in the radio.
3)Solder a wire from one side of the switch to Pin #13.
4)Solder a wire from the other side of the switch to Pin #12.
5)That's it .Put the radio on 'Band D' then flip the switch to jump up to 28.300 to
28.500.

Tweak and peak

Audio Limiter - Cut R249

AM Power - VR13
SSB Power - VR12

Cobra Mods Radio Modulation Power7 PLUSVR4 or CUT

D8L11, L12, L1310 PLUSVR4 or CUT D8L11, L12, L1318 LTDCUT D13 or CUT R84L7,
L6, L518 PLUSCUT D12L 718 RVRV501 or CUT D502L304, L305, L30619CUT D11L5, L8,
L919 GTLVR6 or CUT D9L15, L16, L1719 LTDVR6 or CUT D9L15, L16, L1719 LTD
CLASSICVR4 or CUT D7L7, L819 MREMOVE C73L8, L5, L319 PLUSRV501 or CUT C511L305,
L30619 PLUS (Plastic Case)RV4 or CUT D8L11, L12, L1319 XSCUT D10520 B&KCUT CD20 &
CD21T11, T10, C6020 LTDCUT D1320 PLUSRV501 or CUT C511L305, L30620 PLUS (Plastic
Case)RV4 or CUT D8L11, L12, L1321REMOVE C105 & C106T11, T10, C60 21A (Old)CUT
D24L9, L821 GTLVR5 or CUT D9L13, L10, L9, L821 LTDVR5 or CUT D9L13, L10, L9,
L821 LTD CLASSICVR4 or CUT D7L7, L821 PLUSCUT 1.5K res. next to TR34L12, L1021
XVR207 or CUT D212L212, L21421 XLRRT4 or CUT D13L15, L12, L1123 PLUSRV501 or CUT
D502L304, L306, L30725 GTLVR5 or CUT D9L13, L10, L9, L825 LTDVR5 or CUT
D9L13, L10, L9, L825 LTD CLASSICVR5 or CUT D9L10, L9, L825 PLUSCUT 1.5K res.
next to TR34L12, L1026CUT D24L7, L828 ACUT CD28 & CD29T12, L2, L529 A (OLD)CUT
D24L7, L829XLRVR5 or CUT D14L15, L12, L1129 GTLVR4 or CUT D11L14, L13, L1229
LTDVR4 or CUT D11L14, L13, L1229 LTD CLASSICVR4 or CUT D11L14, L13, L1229 LTD
GOLDVR4 or CUT D11L14, L13, L1229 PLUSCUT D20L1231 PLUSCUT D19L13, L12, L1132
XLRCUT CD11 & CD12L5, L333 PLUSVR4 or CUT D17L11, L939 LTD (S.O.S.)RV140
PLUSRV104 or CUT D203L305, L30640 XRV201 or CUT D203 or C215L304, L305, L30641
PLUSVR4 or CUT D21L19, L20, L2145 XLRVR105 or CUT D119L113, L10946 XLRVR105 or
CUT D119L113, L10947 XLRVR105 or CUT D119L113, L10950 XLRVR5 or CUT D119 L109 55
XLRVR5 or CUT D119L10962 XLRVR3 or REMOVE C67L16, L15, L1263 GTLVR3 or CUT
D11L11, L10, L966 GTLVR2 or CUT D4L14, L15, L1766 LTDCUT R5467 LTDRV4 or CUT
D212L306, L307, L30877 XVR207 or CUT D212L211, L212, L21478 XVR6 or CUT D9L11,
L12, L1585REMOVE Q17 L3, T486 XLRCUT CD9L3CAM 89ADD 1K res. in series with
C110L13, L12, L987 GTLVR6 or CUT D16L17, L16, L1389 GTLVR6 or CUT D16L17,
L16, L1389 XLRVR5 or CUT D14L15, L12, L1190 LTDVR201 or CUT D203132 (OLD)CUT
Q25T14, T15, L3, C116, (ssb) R136132 ACUT CD39 & CD40R79 (ssb) R87132 XLRR134
or CUT R125L3, (ssb)R130134CUT D40 & D41L8, L10 (ssb)VR15135 (OLD)CUT Q25T14,
T15, L3, C116 (ssb)R136135 XLRR134 or CUT R125L3, (ssb)R130138 A (OLD)CUT D40
& D41L8, L10 (ssb) VR15138 XLRVR7 or VR6VR8, (ssb)CT7139VR12 or CUT D63L12,
L10, (ssb)VR15139 XLRVR7 & VR6VR8, (ssb)CT7140 GTLCUT R104VR6, (ssb)VR7142
GTLCUT R104VR6, (ssb)VR7146 GTLVR5 or CUT TR29VR10, (ssb)VR6148 GTLCUT
R131VR10, (ssb)VR11148 GTL-DX (early prod. model)VR5VR11, (ssb)VR7148 GTL-DX
(late prod. model)REMOVE VR14 or CUT TR32VR13, (ssb)VR12148 GTL-BVR14RV15,
(ssb)RV13148 GTL-DX (copy ver.)RV12RV11, (ssb)RV6,RV31000 GTLVR6 or CUT D16L17,
L16, L13, (ssb)2000 GTLCUT R131VR10, (ssb)VR11GTL 150RV14RV13,
(ssb)RV12,RV4

Cobra 25 GTL/LTD/CLASSIC

SAMS PHOTOS: 207

AM LIMITER: D-9
POWER TWEAKS:
1. Change R76 (3.3k) to a 1k (located near mike socket)
2. Change R43 (10 Ohm) to a 2.7 Ohm.
3. Change R108 (1 Ohm) to a .47 Ohm.
4. Replace stock final with a 2SC1969 transistor.
5. Re-tune coils L10,L9,L8 for maximum forward power.

MODULATOR
PARTS NEEDED: 1- 220uF (16 to 25 volt) electrolytic capacitor.
1- 100 to 200 Ohm resistor. (1/4 to 1/2 watt)

ASSEMBLY:
1. Make sure your radio is peaked out.
2. Unsolder JP6 near final.
3. In JP6 holes, solder the 220uF capacitor. (negative side of cap. faces final)
4. On the solder side of the board, solder the resistor across the 220uF
capacitor.
You can use different resistor values to get the desired dead-key.

VARIABLE POWER:
1. Find the two wires that are attached to the RF gain control, follow them to the
PC board and UNSOLDER them.
2. Solder in a jumper wire from where you removed the wires on the board. This will
restore receive.
3. Place the two wires from the RF gain control in your mod kit by soldering one
wire to each of the 220uF capacitors leads.

REPAIR TIPS:
25 GTL:
1. Channel display reads all 7's or 8's: Leaky/shorted C104(470uF 10v). Replace
with a 16v or 25v.
2. NO TX: Check for shorted 33uF(10v) capacitor across C87.
3. OVERMOD: Check D19,TR14,VR5
25 LTD
1. OVERMOD: Check D9
2. LED goes out and NO TX when keyed up: Check C118
25 LTD Classic:
1. Burned R89(15 Ohm 1/2 watt): Replace with a 1 watt.
2. OVERMOD: Check for missing or cut D9, missaligned VR5.

Cobra 29 GTL/LTD/CLASSIC

POWER TWEAK #1:

1. Change R58(10 Ohm) to a 2.7 Ohm.
2. Change R123(1 ohm) to a .47 Ohm.
3. Re-tune L14,L13,L12 for maximum forward power.

POWER TWEAK #2
1. Remove final and replace with a 2SC1969 transistor.
2. Remove R123 and replace with a jumper.
3. Replace C58 with a 180pF capacitor.
4. Re-tune coils.
CAUTION!!! I do not know if both of these power mods can be done at the same
time!!!

SAMS PHOTOS: 217

AM LIMITER: D-11
MODULATOR AND VARIABLE POWER
ASSEMBLY:
The instructions are the same as the Cobra 25 above,EXCEPT the following:
1. Unsolder JP36 instead of JP6.

REPAIR TIPS:
29 GTL:
1. "Motorboating": Locate C242(.001)on pin 5 of TA7222 audio ic and move to pin 4
of ic.
2. Weak mic gain: Some raios have a 2SC372 mic amp. Replace with a 2SC945.
3. Receive on adjacent channel: Bad solder joint to C131 (next to 10.240 crystal).
29 LTD:
1. OVERMOD: Check D11
2. PLL dead, no TX or RX: Shorted C112
3. No TX/RX with Channel LED lit on RX and then goes out when keyed: Bad /shorted
C119.
29 LTD Classic:
1. OVERMOD: Check D11. Missaligned VR4.
2. Internittent audio/modulation: Bad solder joints on pins 1&2 or 2&3 of audio
ic.
3. TUNE UP TIPS: L11 is the TVI trap. DO NOT adjust!!! Stretching L12 gets moe
output. L14 peak is about a turn or two up from factory original setting.

Cobra 148 GTL

POWER TWEAKS:
1. Remove TR24
2. Change R126 (10k) to a 2.2k
3. Change R124 (10k) to a 4.7k
4. Re-tune L37 and L38 for maximum AM forward power.

SAMS PHOTOS: 249

MODULATION: Cut R131
AM POWER: VR10
SSB POWER: VR11

CHANNEL TWEAKS:
I have found that the easiest way to do this without hacking your radio with a lot
of switches is to install the EXPO 100 kit "L" expander kit.
This is an excellent kit and installs quickly with very little tools. This way you
don't have to fumble around trying to remember which switch goes where, etc...

CLARIFIER:
1. Cut one side of R44 and D52. Remove R174 and solder a jumper wire in its place.
2. Follow the RED WIRE from the clarifier control to where it connects to the PC
board and cut it loose.
3. Solder this RED WIRE to the circuit board ground.
NOTE: Some radios have a YELLOW WIRE instead of the RED WIRE.
4. Follow the ORANGE WIRE from the clarifier control to where it connects to the PC
board and UNSOLDER it.
5. Resolder this ORANGE WIRE to pin 3 of the MB3756 regulator.
With any luck, you should slide about 5Kz down and 1Kz up.

GRANT-XL (8719 PLL)

POWER TWEAKS:
1. Remove TR24
2. Replace R126 (10k) with a 2.2k.
3. Replace R124 (10k) with a 4.7k
4. Re-tune coils L37 and L38 for maximum forward swing on AM mode.

MODULATION: Remove R131

AM POWER: VR10
SSB POWER: VR11

CLARIFIER:
1. Find D52, R44 and R174 and remove them.
2. Solder a jumper from where you removed R174
3. Follow the WHITE WIRE from the clarifier control to where it attatches to the PC
board and UNSOLDER it.
4. Resolder this WHITE WIRE to the PC board ground.
5. Follow the ORANGE WIRE from the clarifier control to where it attatches to the
PC board and UNSOLDER it.
6. Resolder this ORANGE WIRE to pin 3 of MB3756 Regulator.

NOTE: Some radios have different colored wires on the clarifier control. They are:
YELLOW instead of ORANGE
RED instead of BLUE

If all goes well, you should slide about 4 down and 1 up.

WANT MORE SLIDE??

1. Remove D51 and put in a jumper.
2. Install a "super-diode" in place of the stock varactor D35.
3. Add a 4.7uh to 10uh choke to the banded-end of the stock varactor.

10 KC JUMP:
Basically, you need to either add voltage or ground pin #16 on the MB8719 PLL.
Here's how to do a 10 Kc UP jump only:
1. Cut trace to pin #16 on the PLL.
2. Install a 4.7K resistor across the cut you made.
3. Using a SPST switch, one side of the switch goes to the cut-side of pin #16.
4. The other side of the switch goes to pin #9 of the PLL. (8 volts)
When you apply the 8 volts, this pulls pin #16 high causing the 10 kc jump up.
Note that this will not work on all channels.

For a 10 Kc DOWN jump only:

1. Ground pin #16 using a SPST switch. No cut to the PLL is necessary.
Pulling pin 16 low will cause it to jump down 10Kc.
This too will not work on all channels.

For a 10 Kc UP and DOWN switch:

Perform the trace cut/resistor addition described above.
Use a SPDT switch and wire as follows:
1. Center of switch goes to pin #9 of PLL (8 volts)
2. One side of switch goes to the cut side of pin #16.
3. The last side goes to pin #18 of PLL (or ground)
This will allow you to jump 10Kc up or down.

COBRA 140,142 GTL , PRESIDENT P-400, UNIDEN WASHINGTON-(8719 PLL)

MODULATION: Remove R104 or TR32

AM POWER: VR6
SSB POWER: VR7
"RX" METER: VR1
"TX" METER: VR10
SQUELCH: VR2
TX FREQ.: VR3
CARRIER BAL: VR5
DRIVER BIAS: VR8
FINAL BIAS: VR9
MOD. METER: VR12

POWER TWEAK
1. Remove TR32
2. Replace R99 (10k) with a 2.2k
3. Replace R94 (10k( with a 2.2k
4. Re-tune coils L36,L37 for maximum forward AM power.

CLARIFIER:
1. Remove R187
2. Remove D36
3. Jumper D35
4. Follow the RED WIRE from the clarifier control to the PC board and UNSOLDER it.
5. RESOLDER this RED WIRE to pin 3 of regulator IC MB3756.
6. Follow the ORANGE WIRE from the clarifier control to the PC board and UNSOLDER
it.
7. RESOLDER this ORANGE WIRE to the PC board ground.
NOTE: The Orange and Red wires may need to be reversed in some radios for this to
work right.
8. Re-align center slot by adjusting CT3.
If all went well and you didn't smoke your radio, you should slide about 1 Kc up
and 4 Kc down.

NEED MORE SLIDE??: Install a 5.6uH choke on the banded end (grounded end) of the
varactor diode D37 or replace D37 with a super diode.

CHANNEL TWEAKS:

EASY TWEAK: Install EXPO 100 kit "B".

FOR THE DRILL HOLES ALL OVER MY RADIO LOVERS...:
1. Replace 11.1125 crystal with a 11.3258 crystal.
2. Isolate the ground pin 10 of the MB8719 PLL by cutting the PC trace.
3. At this point, turn your radio on and check to varify that all channels are
locked in and working. If it is not, adjust these in the following order:
a. CT3 for USB.
b. L20 for LSB.
c. L19 for AM.
4. Install a SPST switch between pins 11 and 12 of the MB8719 PLL
5. Install a SPST switch across the cut you made to isolate pin 10.
6. Check all connections for shorts.
7. Check to make sure everything is working before you drill holes for the
switches!

ROAD MAP:

SW1 / SW2 DOWN: NORMAL 1-40

SW1 UP / SW2 DOWN: (ch.15-27) 26.815 to 26.955
SW1 UP / SW2 UP:
1= 27.605 6= 27.505 11= 27.565 20= 27.525
2= 27.455 7= 27.515 12= 27.585 23= 27.575
3= 27.465 8= 27.535 13= 27.595
4= 27.485 9= 27.545 14= 27.605
5= 27.495 10= 27.555 16= 27.475
SW1 DOWN / SW2 UP: (ch. 1-40) 27.605 to 28.045

COBRA 2000 GTL

MODULATION: VR12 or Cut R131

AM POWER: VR10
SSB POWER: VR11
AM SIGNAL METER: VR1
SSB SIGNAL METER: VR2
SQUELCH: VR3
CARRIER BALANCE: VR4
TX FREQ.: VR5
TX METER: VR6
MODULATION METER: VR7
FINAL BIAS(50 Ma): VR8
DRIVER BIAS(25 Ma): VR9

POWER TWEAK:
1. Remove TR24
2. Replace R126 (10k) with a 2.2k
3. Replace R124 (10k) with a 4.7k
Re-tune coils L37,L38 for maximum forward power.
REPAIR TIPS:

Frequency counter eratic:

1. Find D528 (5.7v 1/2W zener) located in the freq. counter module.
2. Replace it with an NTE-136A 1 watt zener.

Transmit on SSB, but not on AM:

1. Find the regulator TR41 (2sc1419) and remove it.
2. Replace with a GE-66(10 amp) or an NTE-152 (7 amp)

Channel display glows dim after radio is shut down, freq. counter may be unstable
1. Find Fet-501 and Fet-502 located in freq. counter module and replace them.
Older models use: 2SK19GR
Newer models use: 2SK192A

CLARIFIER:
1. Remove R44 and D52.
2. Remove R174 and put a jumper in its place.
3. Follow the YELLOW wire from the clarifier control to where it connects to the PC
board and UNSOLDER it.
4. Solder this YELLOW wire to the PC board ground.
5. Follow the RED wire from the clarifier control to where it connects to the PC
board and UNSOLDER it.
6. Solder this RED wire to pin #3 of MB3756 regulator.
7. Find the BROWN wire on the clarifier control UNSOLDER it, and tape it out of the
way.

No smoke? Then you must have about 1Kc slide up and 5Kc down!

Uniden WASHINGTON (858 pll)

MODULATION: VR7 or cut D23

AM POWER: VR8
SSB POWER: CT7
RX COILS: L3 thru L8
TX COILS: L32,L30
SAMS PHOTOS: #126,127,128,170,171,176,179,200,207

POWER TWEAKS:
(Mike circuit changes:)
1. UNSOLDER banded end of diode D21 and lift up.
2. UNSOLDER banded end of diode D22 and lift up.
3. SOLDER a 4.7 k resistor across where D21 and D22 was unsoldered.
4. Replace R78 (27k) with a 56k.
5. Replace R84 (4.7k) with a 2.2k.

(Transmit circuit changes:)

1. Replace C174 (56pF NPO) with a 82pF NPO ceramic capacitor.
2. Replace C173 (180pF NPO) with a 220pF NPO ceramic capacitor.
3. Re-tune coils L32,L30,L29,L28 and VR8 for maximum forward AM power.

CLARIFIER:
1. UNSOLDER and remove D30.
2. UNSOLDER and remove D29.
3. Add a jumper in the holes from where you removed D29.
4. Cut the end of R119 that is closest to D29.
5. Add a jumper wire from R119 (the cut end) to the banded end of D44.
6. Follow the PURPLE/WHITE wire form the clarifier control to the PC board and
UNSOLDER IT.
7. Resolder this wire to the PC board ground.
8. If all went well, you should slide 1 kc up and 3 kc down.

KNOWN BUGS:
The AM regulator 2SC1419 is WEAK. UNSOLDER it and toss it in the trash.
Replace it with a GE-66, ECG-152 or a NTE-152.
Relay buzzes on SSB, no am transmit, lights go dim, or the fuze pops sometimes?
Replace C179 ( a 2.2uF 25v tantalum cap located near finals) with a standard 2.2uF
electrolytic capacitor.
PAY ATTENTION to the "+" and "-"!!!

Uniden PRO-510XL,PRO-500D,PRO-520XL

POWER TWEAKS:
1. Locate the 2.7 ohm resistor in front of the final bias resistor(15 Ohm w/RF
bead) and change it to a .47 Ohm. (DO NOT change the 15 Ohm resistor!!)
2. Re-tune L9,L6,L5,L4 for maximum forward power.

MODULATION: Cut D14

AM POWER: L6,L5
VR1: Squelch
VR2: TX meter
VR3: RX meter
VR4: RX IF gain

Uniden PC-66,PC-66A

MODULATION: VR5 or cut D9

AM POWER: L13,L10,L9,L8

POWER TWEAK: (ALSO WORKS ON: Uniden AR44,AX44,AR711)

1. Replace R76 (3.3k) with a 1k.
2. Replace R43 (10 Ohm) with a 2.7 Ohm.
3. Replace R108 (1 Ohm) with a .47 Ohm.
4. Re-tune coils L13,L10,L9,L8 for max forward power.

ZACHARY T. (new model w/2816 pll)

POWER TWEAK:
1. Remove C128 (.47uF).
2. Remove TR16.
3. Replace R132 (1k) with a 470 Ohm.
4. Replace R50 (3.9 Ohm) with a 1 Ohm.
5. Re-tune coils L13,L12,L11 for maximum forward power output.
6. Jumper C61 with a 67pF capacitor.
7. Replace TR10 (2SC2029) with a 2SC1969 then tune L16,L17 and spread L14 For even
power across band.
8. Remove D13 and replace with a jumper. (This supplies more power to final)

MODULATION: VR6 or cut D16

AM POWER: L13,L12,L11
RX COILS: L1 thru L8, VR1
SAMS PHOTOS: #223,229,235,243,272,282

CHANNEL TWEAK:

1. Use EXPO 100 kit "A" for 26.515 to 27.855 coverage.

2. Isolate pin 9 on the pll for a 5kc drop.

77-285 MIDLAND There are two printed ciruit boards for the 77-285. You must first
determine which you have.Circuit board "A"This board can be identified because D18
has been cut.To restore full power simply resolder D18 or replace it.Circuit board
"B"On the "B" circuit board D18 is intact (has not been cut out).To restore full
power, locate D18and trace the etch. Put a solder bridge between the open
pads. Channel Conversion:STEP 1. Take the bottom portion of the case off and unplug
the speaker.STEP 2. With the bottom of the case off, turn the radio over and in
this position the Midland name should be upside down. Tilt the chasis forward
toward the face plate. As you look at the inside panel the LC7232 IC
chipshould be readable and pointing toward you (upper right corner). You need
to opensolder bridges 5 and 6 from left of the chassis(bottom left). 77-290
MIDLAND STEP 1 Remove top and bottom cover.STEP 2. Prepare an 8" small gauge jumper
wire Tin both ends.STEP 3. Remove the 1K ohm chip resistor on the radio front
panelSTEP 4. At the removed resistor location, solder the prepared jumper to the
pcb pad nearest the center of the radio.STEP 5. Solder a 1K ohm 1/8 watt lead
resistor to the other end of the jumper.STEP 6. Solder the free end of the resistor
to the emitter lead (lead nearest the rear of the radio) of Q61.STEP 7. Turn the
radio over so the bottom of the pcb is facing up and the front is closest to
you.STEP 8. Locate chip resistor R63 and remove 240 Channels:Press and hold "DW"
and "9" then turn radio on. Select bands by using the "19" button.To set for 28Mhz
to 29.7 Mhz press and hold "LCR" and "eMIC"e then turn radio on. To switch back to
40 channel mode repeat process. Microphone Gain:1. Chip resistor R138 controls mic
gain decreasing the value of the resisitor increases the gain. Generally have270
ohm, the value can be as low as 150. If too much gain is used oscillation may
occur. TRC485 Audio Limiter cut RV5 or cut R111 4.7K resistorNo SSB Control for
ALCAM Power Level RV 10Open Clarifier:Remove the 5 volt switched voltage from
clarifier control. (REMOVE THEFACE PLATE TO CUT THE TRACE). Solder 4.7k resistor
from SJ32 to the closest leg of clarifiercontrol. snip d21 by crystal on main
board. Jump surface mount resistor 181 by clarifier control Galaxy DX77HML Extra
Channels Modification

1.Remove the top of the case (The Part that does not have the speaker on it) and
locate the wire (is usually green or red about 2 inches long)toward the front of
the radio.

2. Unsolder it from the ground and the two pins. After you have removed this wire
make sure there is no solder connecting the two pins together.

3. Find the connector toward the front right of the radio labeled 10K and reconnect
this plug to the connector on the circuit board. (NOTE: This plug may already be
attached when you get your radio.)

4. All thats left to do is put the case back on and your done.

Modulation Mod

VR14 may have been adjusted or TR53 may have been cut or removed

Variable Alignment Points That May Have Been Adjusted

VR1=AM S-Meter VR2=SSB/CW S-Meter VR3=SSB Squelch VR4=AM Squelch Range

VR5=FM Deviation VR7=Carrier Balance VR8=RF Transmit Meter VR10=1st Final TX Bias

VR11=Driver For TX Bias VR12=ALC For SSB Power VR13=AM High Power

VR14=AMC for AM Modulation VR16=AM Low Power VR20=2nd Final TX Bias

VR21=Frequency Adjustment Carful on this one

Euro 3900 Channel Modification

Remove the bottom cover, be carful not to pull the speaker wire out. There is a
black plastic rectangular plug (CN5) which is in the front center of the radio
right in front of the gold colored crystal. Using small needle nose pliers, pull
the plug off and
reinsert it in the next slot. You now have the 11 meter band on Band D. NOTE: You
also have to pull out the calibrate knob
to get the extra channels.

Euro 3900 Power Mod

Locate the trim caps labeled "AMP", "MOD" AND "SSB". Turn these adjustment screws
all the way to the right. These caps are on the same board as CN5, but on the
oppisite end. Thats all there is to it. You should see around 15 watts on AM and
25 watts on SSB

PLL 02A MODS

This chip can be found in many radios. This mod might work on the SSB units also.

G.E.
3-5804D,3-5811B,3-5812A,3-5813B,3-5819A

Midland

76-858,76-863,76-886,77-830,77-838,77-849,77-857,77-882,77-888,77-899,77-955,77-963

And just about anything with a PLL 02A chip in it.

The 23-channel radios will give different channels.

1)Cut the Trace going to PIN #11.

2)Solder a 3.3 K resistor across the cut.
3)Solder 1 leg of a SPST switch to PIN #8.
4)Solder the other leg to PIN #11.

1 - 26.805 . . . . . . . 4 - 26.845 . . . . . . . 7 - 26.875

2 - 26.815 . . . . . . . 5 - 26.855 . . . . . . . 8 - 26.895
3 - 26.825 . . . . . . . 6 - 26.865 . . . . . . . 9 - 26.905

1)Cut the Trace going to PIN #10.

2)Solder a 3.3 K resistor across the cut.
3)Solder 1 leg of a SPST switch to PIN #9.
4)Solder the other leg to PIN #10 after the resistor.

This will give you 26.645 to 26.745 Mhz on channels 1 - 38.

1)Cut the Trace going to PIN #9.

2)Solder a 3.3 K resistor across the cut.
3)Solder 1 leg of a SPST switch to GROUND.
4)Solder the other leg to PIN #9 before the resistor.

This will give you 27.425 to 27.705 Mhz on channels 12-38.

1)Cut the Traces going to PIN #10 and PIN #9.

2)Solder a 3.3 K resistor across the cuts.
3)Using a DPDT Center-Off type switch solder wires from the PLL to the back of the
switch as shown.

When the switch is UP.

This will give you 26.435 to 26.7455 Mhz on channels 10 - 38 .

When the switch is DOWN.

This will give you 26.755 to 27.055 Mhz on channels 10 - 38 .

SuperStar 121

+ 10 KHz Jump Switch

1)Get a SPST switch and mount it in the radio.
2)Find IC 6 & 7 by the PLL chip. You will see J25 and J27
3)Solder a wire from one side of the switch to J27.
4)Remove the jumper that is J25.
5)Install a 4.7k Ohm resistor in its place.
6)Solder a wire from the other side of the switch to J25.(see Picture)
5)That's it .Flip the switch to jump up one channel.

Channel Expansion

1)You will need 3 SPST switches and mount them in the radio.
2)Find the PLL MC145106.
3)Locate pin # 10 and cut the trace going to this.
4)Switch #3 will be soldered to the cut traces on pin # 10.
4)Solder wires to the other 2 switches as in the picture above.
5)That's it!

ALl the switches down will give the normal channels of the radio.

With the radio in 'HIGH' band and switch 1 UP , 2 DOWN , and 3 DOWN:

You get 27.845 - 27.955 on channels 10 to 19.

With the radio in 'MID' band and switch 1 UP , 2 UP , and 3 DOWN:

You get 27.925 - 28.065 on channels 1 to 12.

With the radio in 'HIGH' band and switch 1 UP , 2 UP , and 3 DOWN:

You get 28.045 - 28.155 on channels 27 to 38.

With the radio in 'HIGH' band and switch 1 DOWN , 2 DOWN , and 3 UP:

You get 26.135 - 26.575 on channels 1 to 40.

Emperor TS-5010

Frequency Expansion

1) This is one of the more difficult mods out there.

2) Open the bottom cover of the radio .
3) Find the PLL Board. Its the one with the 64 pin chip on it.
4) At the front of this board by the PLL chip ther are 2 resistors R540 and R539.
5) Cut them.
6) Close the radio up. Turn it on.
Tweak and Peak

Audio limiter - R247

AM Power - VR 111
SSB Power - VR 103

RIT Modification

1)Remove top and bottom covers.

2)On the top of the main board find D140.Cut it.
3)Solder one end of a 10 OHM resistor to the location in the picture below.
4)Take a 7.5v zener diode and solder the end without the band to the small brass
shield.
5)Now solder to other end of the diode to the open end of the resistor.

6)Find the PC Board that is behind the RIT Knod

7)Cut the trace as you see in the picture above.

8)Solder a wire(See the green wire in the pics) from the point that the diode and
resistor meet togeteher to the bottom of the board where you made the cut.

Aligning the RIT

1)Place the radio so that the smaller PC Board is facing up.

2)Turn it on and dial up 28.000 MHZ and put the rit dead center.
3)On the samller PC Board locate J502.(upper right)
4)Pull the grey cable off the board and connect it to your frequency counter.(Sorry
you can't use them $49 dollar specials from copper.You have to have a frequency
counter with a probe on it)5)Hook up the probe and if it should read 38.695 +/- 100
Hz.
6)If not then adjust L501.
7)Put the radio back together.You shound have about 6KHz of slide.

Extra Channels for the 5080 PLL

COBRA 32 XLR , 86 XLR and Tram D42

1) Mount 2 SPST toggle switches in a good loacation on the radio.

2) Locate PIN #8 of the PLL and unsolder the green wire and remove any excess
solder .
3) Cut the trace that is connecting pin #8 to the PCB.
4) Resolder the green wire to the other side of the cut trace.
5) Now take a 100k resistor and solder one end to pin #8 and the other end to
ground on the PCB.
5) Solder the wires onto the switches and pins of the chip like in the diagram
above.

With Switch #1 down and Switch #2 down will be regular CB channels

With Switch #1 up and Switch #2 up will be the low channels

.3 - 26.665________ 15 - 26.815
.4 - 26.685________ 16 - 26.835
.5 - 26.695________ 17 - 26.845
.6 - 26.705________ 18 - 26.855
.7 - 26.715________ 19 - 26.865
.8 - 26.735________ 20 - 26.885
.9 - 26.745________ 22 - 26.905
11 - 26.765________ 23 - 26.935
12 - 26.785________ 24 - 26.915
13 - 26.795________ 25 - 26.925
14 - 26.805________ 26 - 26.945

With Switch #1 up and Switch #2 DOWN will be the HI channels

11 - 27.405________ 19 - 27.505
12 - 27.425________ 20 - 27.525
13 - 27.435________ 21 - 27.535
14 - 27.445________ 22 - 27.545
15 - 27.455________ 23 - 27.575
16 - 27.475________ 24 - 27.555
17 - 27.485________ 25 - 27.565
18 - 27.495________ 26 - 27.585

858 PLL FREQ MOD

COBRA 138 139 XLR (OLD) PRESIDENT GRANT, WASINGTON,MADISON , ROYBN 510 , 520D ,TRC-
449 457 AND 458

1)FIND PIN #19 OF THE 858 CHIP.THIS PIN WILL BE CONNECTED TO GROUND WITH A SMALL
TRACE. CUT THE TRACE AND SOLDER A 4.7K OHM RESISTOR ACROSS THE CUT .

2)FIND PIN#21 AND DO THE SAME AS YOU DID TO PIN #19.

3)INSTALL A SPDT/CENTER OFF TYPE AND ALSO A SPST SWITCH IN THE CHASSIS OF THE
RADIO.SOLDER THE WIRE FROM THE CHIP TO THE 2 SWITCHES AS IN THE PIC ABOVE.

4) TURN THE RADIO ON AND SEE IF ALL THE CHANNELS WORK.IF NOT THE YOU WILL NEED TO
"BROAD BAND" THE RADIO.CUT THE 2 TRACES AND INSTALL THE 2 JUMPERS AS IN THE PIC
BELOW.

Now with s1 up and s2 center this is the reg CB

With s1 up and s2 up will be 27.455 to 27.805 on CH. 8-40
With s1 up and s2 dn will be 27.855 to 28.005 on CH.8-20
With s1 dn and s2 up will be 26.455 to 26.805 on CH. 8-40
With s1 dn and s2 dn will be 26.855 to 26.955 on CH.8-16
With s2 dn and s2 center will be 26.085 to 26.45 on CH. 11-40

Broad Band Alignment

Unlocking the Clarifier

1)Cut R-117
2)Cut D-30
3)Find the backside of the clarifier knob.Follow the PURPLE and BROWN wires and cut
them just before they connect to the PCB.
4)Solder the PURPLE wire to an 8 VDC source.
5)Solder the BROWN wire to GROUND.

Extra Channel mods for the MB8719 PLL

If your radio has a MB8734 pll change it to a MB8719 COBRA 140 , 142 GTL ,
PRESIDENT WASINGTON AND McKINLEY AND P400

1) Mount 2 SPST toggle switches in a good loacation on the radio.

2) Locate and unsolder the 11.1125mhz Crystal and replace it with a 11.3258 mhz
crystal.
3) Locate pin 10 of the mb8719 chip.Cut the trace that is connected to it.
4) Solder the wires onto the switches and pins of the chip like in the diagram
above.

COBRA 148 , 2000 GTL , UNIDEN GRANT AND MADISON

The mod is basically the same for these radio EXCEPT that there is no PC trace
going to pin#10 on this PLL.

On the Cobra 2000gtl you will find a MB8734 pll replace it with a MB8719 PLL

Clarifier Modification

PRESIDENT GRANT AND MADISON

1)Cut d-52 and r-148.Find r-174 and solder a wire across the resistor.
2)Find the RED wire that comes off the clarifier control and cut it just before it
connects to the PCB. Take that wire and solder it to GROUND on the PCB
3)Cut the orange wire just like the red wire but solder this wire to pin # 3 if IC-
4 the MB3756 ic regulator.

This should give you about 5 khz is slide on this radio.

COBRA 148 GTL & UNIDEN GRANT XL

1) Cut R44 and D52.Find R174 and jump it .

2)Follow the red wire from the clarifier knob and cut it just before it connects to
the PCB.Take this wire and solder it to Ground.
3)Find the orange wire from the clarifier and cut it the same.Then solder it to pin
#3 of the mb3756 ic.

This should give you about 6khz of slide.

COBRA 2000 GTL

1) Cut R44 and D52.Find R174 and jump it .

2)Follow the YELLOW wire from the clarifier knob and cut it just before it connects
to the PCB.Take this wire and solder it to Ground.
3)Find the RED wire from the clarifier and cut it the same.Then solder it to pin #3
of the mb3756 ic.
4)Cut the brown wire off the clarifier knob.

This should give you about 6khz of slide.The fine control will work also.

COBRA 140GTL,142GTL,PRESIDENT WASHINGTON,McKINLEY,AND P400

1)Cut r187 and d36

2)Find the red and orange wires commong off the clarifier knob.Cut them where they
connect to the PCB.
3)Take the red wire and solder it to pin #3 of the mb3756 IC.Solder the orange wire
to PCB ground.

NOTICE:On some radios the red and orange might have to be reversed to slide in the
right direction.

10 Kc jump switch

Cut the trace going to pin #16 and bridge it with a 4.7k resistor. Then use a SPDT
center off switch solder the middle terminal of the switch to the pin before the
cut. Next solder one side to a 5 volt dc source and the side of the switch to
ground or pin #18.

COBRA 142 AND 140GTL

MOD.-R104 AM PWR- VR6 SSB PWR-VR7

COBRA 2000 148GTL PRESIDENT WASHINGTON MADISON

MOD.-R131 AM PWR.-VR10 SSB. PWR-VR11

Cobra 146 GTL

Realistic TRC-453

Uniden AR-144

Uniden PC-122 & AR-144

Uniden Pro -810e Base

...and similiar SSB radios.

Clarifier modification: Cobra 146 & AR-144

1) Lift anode of D-30 and connect a 5.6 uH choke in series.

2) Cut D-32.
3) Cut both traces on the PCB going to the clarifier .
4) Solder one wire to PCB ground.
5) Solder a wire from the other cut trace to an 8 VDC source
(note: 8 volts can be found on the cathode of D-50)
6)This should give you 5 kc of slide.If more slide is wanted then change D-30 to a
super slide doide.

Clarifier modification: TRC-453 and Uniden PC-122

1)Find the backside of the clarifier knob.

2)Solder the bottom pin to GROUND. 3)Solder a wire to the top pin of the PCB.
This pin should be cut loose from any traces going to it!)
4)Solder that wire to an 8VDC source.This can be found on the second jumper behind
the PLL chip(IC-2).
5)Cut D-25.

Clarifier modification: Uniden Pro-810e

1) Cut D-25.
2) Cut D-32.
3) Cut both traces on the PCB going to the clarifier .
4) Solder one wire to PCB ground.
5) Solder a wire from the other cut trace to an 8 VDC source
(note: 8 volts can be found on the trace that connects R-107 & R-106
6)This should give you 3 kc of slide.If more slide is wanted then jump D-24 with a
piece of wire.(Sometimes it works)

Channel Expansion:

1)Unsolder the PLL chip.UPD2824 or D2824.

2)Throw it away.Its can't be modified.
3)Solder in a new PLL UPD2816.
4)Connect pin #20 to pin #21 GROUND.
5)Solder a wire from pin #9 to one side of a SPST switch.
6)Solder a wire from PCB GROUND to the other side of the switch.
7)If all goes well this should give you 27.420 - 27.860 Mhz.
Yes, i know 27.420 in between the channel SO use the clarifier for the 5 kc
offset.
8)If you can't get all the frequency coverage then adjust L-14 the VCO coil.

"Peaks and Tweaks"

VR 10 is AM power
VR 6 is ALC
VR 5 is AM Modulation
VR 7 is RF Power meter
VR 1 is S-meter adjust.

DeerSlayer 240
Frequency Expansion

1) Unplug the radio and turn it on.(This is to drain the power out of the cpu)
2) Remove the covers off of the radio .
3) The radio has a removable plug on the front board with a blue jumper on it.
4) Disconnect this plug.
5) Close the radio up. Turn it on.
6) The radio should now have 6 bands (A-F). Use the chan 9 button to change bands.

President Grant Export Mods

President Grant extra Channels

1)The switch needed is a SPST/CENTER-OFF type.Mount this in the radio somewhere.

2)Find the PLL MB8719 chip.Find pin #11 and cut the trace going to it on the foil
side of the PCB.
3)Solder a 4.7k ohm resistor across the cut that you just made.
4)Now you are ready to attach the wires from the switch to the locations on the
PCB.
5)Solder a wire from the top pin on the switch to PCB ground.
6)Solder a wire from the middle pin on the switch to pin #11.
7)Solder a wire from the tbottom pin on the switch to pin #9.
(If you do not get ALL the new channels adjust the VCO coil,l-18)

With the switch in the UP position:

12 = 27.875 17 = 27.935 22 = 27.995 26 = 28.03513 = 27.885 18 = 27.945 23 = 28.025

27 = 28.04514 = 27.895 19 = 27.955 24 = 28.005 28 = 28.05515 = 27.905 20 = 27.975
25 = 28.015 .16 = 27.925 21 = 27.985 .

With the switch in the CENTER position is regular channels

With the switch in the DOWN position:

12 = 26.335 17 = 26.395 21 = 26.455 24 = 26.47513 = 26.345 18 = 26.405 22 = 26.465

25 = 26.48514 = 26.355 19 = 26.425 23 = 26.495 26 = 26.49515 = 26.365 20 = 26.445
27 = 26.50516 = 26.385 .

President Grant SLIDER mod

1) Cut D-45.
2) Find D-79 and jump it (Solder a wire across it)
3) Remove r-120 and replace it with a 470 ohm resistor.
4) Find the BLUE wire from the clarifier knob and cut it just before it connects to
the PCB. Solder it into the hole that is next to where R-120 is.
5) Find the GREY wire from the clarifier knob and cut it just before it connects to
the PCB. Solder it to a constant 8.5 volt supply.(This can be the center pin of TR-
39 )

Hopefully this should give you about 3 khz of slide.

President Grant MIKE wiring

President Grant 'peak & tweak'

MODULATION - Adjust VR-14

AM POWER - VR-13
SSB POWER - VR-12

SEARS AM/SSB ROADTALKER BASE/MOBILE

SEARS ROADTALKER BASE/MOBILE

1)Open the radio and you will find a metal case around the pll chip.unsolder this.
2)Cut the trace around pin 9 and 8 . 4)Solder a 4.7k resistor from pin 8 to ground.
5)Install a 6 posistion/ double pole rotary swicth in the radio.then run wires (the
red lines) from the switch posistions to the locations on the pc board. 6)Solder a
1n914 diode from pin 1 to pin 4 on the switch. 6)Solder a wire from pins 2A to 3A
to 4A to 5A.

Adjust t302, the VCO,so that the radio will TX/RX on all the extra channels.
HINT:USE A PLASTIC TUNING TOOL TO MAKE THIS ADJUSTMENT OR YOU WILL BREAK THE COIL!!

POSITION 1

Channel 1 to 40 is 26.485 to 26.925

POSITION 2

All the regular CB channels

POSITION 3

Channel 12 to 27 is 27.425 to 27.595

POSITION 4

Channel 1 to 40 is 27.605 to 28.045

POSITION 5 AND 6 will give regular CB Channels

CLARIFIER MODIFICATIONS
1)Find the green wire coming off the FINE TUNING control.Follow the wire to the pc
board where it connects and unsolder it.
2)Find the RED wire behind the meter display and solder it to that location(there
is 8VDC there)
3)Find the BLACK wire from the FINE TUNING control and unsolder it from the PCB.
4)Solder this wire to PC GROUND .
5)Find the PURPLE wire from the FINE TUNING control and unsolder that from the PC
board.
6)Solder this wire to the point on the PC board where R303 and the cathode,the end
with the band around it! , of D301.

This mod will give you about 3khz up/down off the "channel".
If you move the clarifier and the radio "drops out" you will need to JUMP d301 and
put the purple wire back to where it was.

RCI 2950 Frequency Modification1. Remove the case. I *think* you can remove
either the top cover or the bottom cover to get to the PC board with the
jumpers. It will be a small PC board immediately behind the front panel.2. Locate
"J2". There will be a jumper on pins P3 and P4.3. Remove this jumper to expand
coverage to 26 MHz - 29.7 MHz.4. Move the jumper from P3-P4 to P1-P2 to expand
coverage to 26 MHz - 32 MHz.5. After moving (or removing) the jumper, press the
CPU reset button (located below J2).NOTE: Operation between 30-32MHz may require
retuning the VCO. CB Channel Readout Modification1. Locate J1. There will be a
jumper on pins P1-P2.2. Remove jumper and place on P2-P3.3. Press the LOCK button
on the front panel. The readout will now display the CB channel number 1-40 --
also will display "A" channels.4. Press LOCK again to return to VFO mode.NOTE: The
SHF button will not operate while in CB mode. This modification will disable
the frequency lock function. CB Channel 9 Select Modification1. Locate J3. There
is a jumper between P1-P2.2. Remove the jumper and place it on P2-P3.3. Press the
"roger beep" button to go directly to CB Channel 9.NOTE: Doing this modification
makes it impossible to turn off the roger beep feature (unless, *possibly* you
make sure the roger beep is turned off before moving the jumper. I'm not
sure). ------------------------------------------------------------------------
"Tuneup" Modifications Adjust VR14 (AMC) for maximum forward modification. Mod
limiterQ32 can be removed for more modulation, but it also disables VR12(SSB ALC)
and disables variable power for SSB. I do not recommendremoving Q32; you'll have
plenty of modulation as is. Tune L34, L13, L14, L46 and L10 in AM mode for
maximum forwardswing, using a peak-reading wattmeter. Try to balance for even
powerfrom top to bottom of frequency range.NOTE: You'll have a LOT of trouble
identifying these cans. Sorry,I don't know for sure where they are either.
Adjust VR13 (AM High Power) for 12 watts dead key with the frontpanel RF power
control at maximum. Adjust VR15 (AM Low Power) for2 watts dead key with front
panel RF power control at minimum.>From the 12-watt dead key you should see a
forward swing of 30-40 watts.>From the 2-watt dead key you should see a forward
swing of 18-20 watts. Adjust VR12 (SSB High Power ALC) for maximum PEP on SSB,
thenback off just a little, with front panel RF power control at maximum.Adjust
VR16 (SSB Low Power ALC) for 5-6 watts PEP on SSB with frontpanel RF power control
at minimum. You should see 40-50 watts PEPon SSB with front panel RF power control
at maximum.--------------------------------------------------------------------
Microphone wiring diagram Pin 1 -- shieldPin 2 -- AudioPin 3 -- TransmitPin 4
-- ReceivePin 5 -- Frequency select up \ These might be reversed.Pin 6 --
Frequency select down
/ -------------------------------------------------------------------- Radios And
Their PLL Chips! PLLCHASSISRADIO MAKE RADIO MODELGREAT
UKNAACADEMY501MSM5807NAALARONB4900M58473PNAAMERICAN MOTORS32311847M58473PNAAMERICAN
MOTORS32311848M58473PNAAMERICAN MOTORS32311849M58473PNAAMERICAN
MOTORS32311850LC7136PCMA002FAMSTRADCB900LC7136PCMA002FAMSTRADCB901TC9106PNAAR44TC91
06PNAAR711PLL02APCMA001SARGUS5000TC9119PA034AUDIOLINE340TC9119PA034AUDIOLINE341TC91
19PA034AUDIOLINE345LC7130NAAUDIOVOXMCB40UPD2810CNAAUDIOVOXMDU6000UPD2812CNAAUDIOVOX
MCB5000SM5118NAAUTOMATICCBR2175PLL02APTBM048A0XAWA/THORN1503PLL02APTBM048A0XAWA/THO
RN1503TC9106PNAAX44TC9106PNAAX711GREAT
UKNABARRACUDAGT868LC7136PTBM134A0XBARRACUDAHP940LC7136PTBM134A0XBINATONE5-
STARLC7136PTBM134A0XBINATONESPEEDWAYPLL02APTBM049BOMANCB910PLL02APTBM049BOMANCB920P
LL02APTBM049BOMANCB930PLL02APTBM048A0XBOMANCB950PLL02APTBM048A0XBOMANCB950PLL02APTB
M049BOMANCBH990SM5118NABOMANCBR9940UPD858CNABOMANCBR9600UPD861CNABOMANCBM6100MC1451
06NABROWNINGMARK
4ATC5080PNABROWNINGBARONTC5080PNABROWNINGSABREPLL02APTBMO48A0XCARDONIROQUOIS
40UPD861CNACDEMARK 26M58472PNACHANNEL MASTERCB6830M58472PNACHANNEL
MASTERCB6832SM5118NACHRYSLER4048076SM5118NACHRYSLER4048077PLL02APTBM048A0XCITIZENMP
L-
5LC7130NACOBRA19+LC7130NACOBRA19DXLC7130NACOBRA19XSLC7130NACOBRA20+LC7130NACOBRA40+
LC7130NACOBRA67LTDLC7130NACOBRA70LTDLC7130NACOBRA90LTDLC7130NACOBRA66LC7136NACOBRA2
1FXMLC7185NACOBRA18RVLC7185NACOBRA23+MB8719NACOBRA140GTLMB8719NACOBRA142GTLMB8719NA
COBRA148GTLMB8719NACOBRA148GTLDX
(EARLY)MB8719NACOBRA2000GTLMB8719NACOBRA47XLRMB8719NACOBRA55XLRMB8719NACOBRAPC879MB
8719NACOBRA46MB8719NACOBRA50MC145106NACOBRA148GTLDX
(LATE)PLL02APTBM122D0XCOBRA148GTL-BPLL02APCMA001SCOBRA148GTLDX
(FAKE)PLL02APTBN121D4XCOBRA150GTLSM5123ANACOBRA18+SM5123ANACOBRA21+SM5123ANACOBRA25
+SM5123ANACOBRA29+SM5124ANACOBRA31+SM5125BNACOBRA33+TC5080PNACOBRA132XLRTC5080PNACO
BRA135XLRTC5080PNACOBRA32XLRTC5080PNACOBRA87XLRTC5080PNACOBRA86TC9106PNACOBRA18LTDT
C9106PNACOBRA20LTDTC9106PNACOBRA21GTLTC9106PNACOBRA21LTDTC9106PNACOBRA26GTLTC9106PN
ACOBRA25LTDTC9106PNACOBRA19GTLTC9106PNACOBRA19LTDTC9106PNACOBRA78XUPD2814CNACOBRA66
GTLUPD2816CNACOBRA1000GTLUPD2816CNACOBRA29GTLUPD2816CNACOBRA29LTDUPD2816CNACOBRA63G
TLUPD2816CNACOBRA87GTLUPD2824CPC833COBRA146GTLUPD858CNACOBRA138XLRUPD858CNACOBRA139
XLRUPD858CNACOBRA21XUPD858CNACOBRA21XL5UPD858CNACOBRA29XLRUPD858CNACOBRA77XUPD858CN
ACOBRA89XLR MC145106NACOLONIALFR360C5121NACOLT357ALC7120NACOLT222LC7120NACOLT510
LC7130NACOLT210LC7136NACOLT295PLL02APTBM048A0XCOLT1200
EXCALIBURPLL02APTBN121D4XCOLT1200DX
EXCALIBURPLL02APTBM125A4XCOLT1600DXPLL02APTBM125A4XCOLT2000DXPLL02APTBN121D4XCOLT32
0DXPLL02APTBN121D4XCOLT320FMPLL02APTBM048A0XCOLT485DXPLL02APTBM048A0XCOLT485DXPLL02
APTBM049COLTSX33PLL02APTBM049COLT290PLL02APTBM049COLT390PLL02APTBM048A0XCOLT480PLL0
2APTBM048A0XCOLT480PLL02APTB049COLT720PLL02APTB049COLT800PLL02APTB049COLT870PLL02AP
TBM048A0XCOLT890PLL02APTBM048A0XCOLT890PLL02APTBM048A0XCOLT1000PLL02APTBM048A0XCOLT
1000PLL02APTBM048A0XCOLT1200PLL02APCMA001SCOLT2400UPD861CNACOLT350LC7120NACOMMTRONV
IIILC7136NACOMMTRONCB40FMC145106NACONNEX3300C5121NACONTACT40FMUPD861CNACONTACTPSC30
1UPD861CNACONVOYCON-400MB8719NACOURIERGALAXYREC86343NACOURIERBLAZER
400REC86343NACOURIERNIGHTRIDER
400RREC86343NACOURIERRANGER400SM5104NACOURIERCARAVELLE 400SM5104NACOURIERCONQUERER
400UPD858CNACOURIERCENTURION 40DUPD858CNACOURIERCENTURION
PLLUPD858CNACOURIERGLADIATOR PLLUPD858CNACOURIERREBEL 40AUPD858CNACOURIERREBEL
PLLUPD858CNACOURIERSPARTAN PLLLC7130NACOURIER GALAXYIVLC7130NACOURIER
GALAXYVLC7130NACOURIER
GALAXYVIMC14568NACRAIGL101MC14568NACRAIGL102NDC40013NACRAIGL131NDC40013NACRAIGL231T
C9106PNACRAIGL104TC9106PNACRAIGL103UPD2814CNACRAIGL150UPD2824CPC581CRAIGL132UPD2824
CPC581CRAIGL232PLL02APCMA001SCTE/ALAN88SLC7137PTBM135AOXCYBERNET
BETA1000LC7137PTBM135AOXCYBERNET BETA2000LC7137PTBM135AOXCYBERNET
BETA3000MC145106NADAKMARK IXMC145106NADAKMARK VPLL02APTBM080DAK
MARKXPLL02APTBM080DAK MARKXPLL02APTBM027DELCO (GM)CBD-10 1977/78PLL02APTBM049DELCO
(GM)1978 SERIESC5121NADICK SMITHD1200LC7130NADICK
SMITHD1450LC7132NADNT4000FMC5121NADNT CONTACT40FMGREAT
UKNAELFTONEELCB6000MC145106NAEXCALIBURBASEMC145106NAEXCALIBURSAMURAIPLL02APCMA001SF
ALCON2000 REC86343NAFANON FANFARE125FREC86343NAFANON FANFARE182FREC86343NAFANON
FANFARE184DFREC86343NAFANON FANFARE185DFREC86343NAFANON
FANFARE185PLLREC86343NAFANON FANFARE190DFSM5104NAFANON FANFARE880DFUPD858CNAFANON
FANFARE100FIUPD858CNAFANON FANFARE350FGREAT UKNAFIDELITY1000MGREAT
UKNAFIDELITYCB300MLC7136PCMA002FFIDELITY2001FMLC7136PTBM134A0XFIDELITYCB2000MLC7120
NAFORMAC240PLL02APTBM049FORMAC88PLL02APTBM049FORMAC120LC7130NAFOXCB340 LC7132NAFOXC
B240LC7132NAFOXCB440MC145106NAGALAXYIIMC145106NAGALAXYSATURNMC145106NAGALAXY44MC145
106NAGALAXY88MC145106NAGALAXY2100C5121NAGE3-5829BC5121NAGE3-5909ALC7110NAGE3-
5804ALC7110NAGE3-5871BLC7130NAGE3-5805BLC7130NAGE3-5826ALC7132NAGE3-
5806ALC7132NAGE3-5808ALC7132NAGE3-5828AM58472PNAGE3-5800AM58472PNAGE3-
5801AM58472PNAGE3-5810AM58472PNAGE3-5821AM58472PNAGE3-5871APLL02APTBM049GE3-
5804DPLL02APTBM049GE3-5810BPLL02APTBM080GE3-5825BPLL02APTBM048A0XGE3-
5825APLL02APTBM048A0XGE3-5825APLL02APTBM080GE3-5825BPLL02APTBM080GE3-5875A
SUPERBASEPLL02APYBM049GE5811BPLL02APTBM049GE5812APLL02APTBM049GE5813BPLL02APTBM049G
E5814BPLL02APTBM049GE5819APLL02APTBM080GE5875A SUPERBASEROYCENAGE3-
5830TC9109PNAGE3-5804GTC9109PNAGE3-
5816AMSM5907NAGEMTRONICSGTX4040MSM5907NAGEMTRONICSGTX5000PLL02APTBM049GEMTRONICSGT4
4PLL02APTBMO49GEMTRONICSGT55PLL02APTBM049GEMTRONICSGTX66PLL02APTBN048A0XGEMTRONICSG
TX77MSC42502PNAGM4170MSC42502PNAGM4175GREAT UKNAGREATGT858BGREAT
UKNAGREATGT868BGREAT UKNAHALCYONCHEETAHGREAT UKNAHALCYONCONDORPLL02APTBM059COXHAM
INTERNATIONALCONCORDPLL02APTBN121D4XHAM INTERNATIONALCONCORDE IIPLL02APTBM133A4XHAM
INTERNATIONALCONCORDE IIIPLL02APTBM059COXHAM INTERNATIONALJUMBOPLL02APTBN121D4XHAM
INTERNATIONALJUMBO IIPLL02APTBM133A4XHAM INTERNATIONALJUMBO IIIPLL02APTBM059COXHAM
INTERNATIONALMULTIMODE IIPLL02APTBM133A4XHAM INTERNATIONALMULTIMODE
IIIPLL02APTBM049HAM INTERNATIONALPUMAPLL02APTBM049HAM
INTERNATIONALVIKINGPLL02APCMA001SHAM
INTERNATIONAL8040LC7136PCMA002FHARRIERCBHQLC7136PTBM134A0XHARRIERCBXLC7136PCMA002FH
ARVARD400MLC7136PCMA002FHARVARD402MPAPC7136PTBM134A0XHARVARD 420MLC7136PCMA002FHARV
ARDH401LC7136PCMA002FHARVARDH407MM48141NAHYGAIN2716PLL01ANAHYGAIN681PLL01ANAHYGAIN6
82PLL02APTBM027HYGAIN2679APLL02APTBM048A0XHYGAIN2705VPLL02APTBM048A0XHYGAIN2705VPLL
02APTBM027HYGAIN2710XPLL02APTBN121D4XHYGAIN2795DXPLL02APTBM048A0XHYGAIN3108
VIIIPLL02APTBM125A4XHYGAIN8795VPLL02APTBM059COXHYGAINVPLL02APCMA001SHYGAIN80PLL02AP
TBMO27HYGAIN681PLL02APTBM027HYGAIN682PLL02APTBMO27HYGAIN2679PLL02APTBM027HYGAIN2680
PLL02APTBM027HYGAIN2681PLL02APTBM027HYGAIN2682PLL02APTBM027HYGAIN2683PLL02APTBM049H
YGAIN2701PLL02APTBM049HYGAIN2702PLL02APTBMO27HYGAIN2703PLL02APTBM027HYGAIN2716PLL02
APTBM048A0XHYGAIN2720PLL02APTBM048A0XHYGAIN2785PLL02APTBN121D4XHYGAIN2795PLL02APTBM
049HYGAIN3107PLL02APTBM027HYGAIN30848LC7120NAHYSTAR100C5121NAINTEKM4035LC7130NAINTE
K49*PLL02APTBN121D4XINTEK1200FMM58473PNAITT4400MLC7120NAJAWSIIPLL02APTBM049JC
PENNYS981-6204PLL02APTBM049JC PENNYS981-6218PLL02APTBM0048A0XJC PENNYS981-
6247SM5104NAJCPENNYS981-6241SM5104NAJC PENNYS981-6246SM5104NAJC PENNYS934-
3831SM5104NAJC PENNYS981-6248UPD861CNAJC PENNYS981-6203UPD861CNAJC PENNYS981-
6221UPD861CNAJC PENNYS981-6237UPD861CNAJC PENNYS981-
6255UPD2812CNAJIL615CBPLL02APTBM049JIL CITIZENBPL524PLL02APTBM048A0XJIL CITIZENMPL-
5PLL02APTBM048A0XJIL CITIZENSSB-M6GREAT
UKNAJOHNSONXK2000MSC42502PNAJOHNSON4170MSC42502PNAJOHNSON4175MSC42502PNAJOHNSON
MESSENGER40MSC42502PNAJOHNSON MESSENGER50MSC42502PNAJOHNSON
MESSENGER80MSC42502PNAJOHNSON MESSENGER191MSC42502PNAJOHNSON
MESSENGER4120MSC42502PNAJOHNSON MESSENGER4125MSC42502PNAJOHNSON
MESSENGER4135MSC42502PNAJOHNSON MESSENGER4140MSC42502PNAJOHNSON
MESSENGER4145MSC42502PNAJOHNSON MESSENGER4230MSC42502PNAJOHNSON
MESSENGER4250NDC40013NAJOHNSON MESSENGER4730MSC42502PNAJOHNSON
VIKING200MSC42502PNAJOHNSON VIKING230MSC42502PNAJOHNSON VIKING260MSC42502PNAJOHNSON
VIKING270MSC42502PNAJOHNSON VIKING430ROYCENAK
MARTD40SM5124ANAK407TC9106PNAK408MC145106NAKEYCOMM1000CCI3002NAKRACO2410CCI3002NAKR
ACO2420CCI3002NAKRACO2430M58473PNAKRACOKCB4005MSM5807NAKRACOKCB4000NIS7264NAKRACOKC
B4003NIS7264NAKRACOKCB4088PLL01ANAKRACOKCB2310APLL01ANAKRACOKCB2320APLL02APTBM027KR
ACOKCB2310BPLL02APTBM027KRACOKCB2320BPLL02APTBM027KRACOKCB2330BPLL02APTBM049KRACOKC
B4010PLL02APTBM049KRACO4020PLL02APTBM049KRACO4030PLL02APTBM049KRACO4045PLL02APTBM04
9KRACO5001PLL02APTBM049KRACO5003ROYCENAKRACOKCB4001ROYCENAKRACOKCB4070TC5080PNAKRAC
OKCB4095SM5104NAKRISXL-45SM5104NAKRISXL-50PLL02APTBM059COXLAFAYETTE1200
FMPLL02APCMA001SLAFAYETTE2400
FMPLL02APTBN121D4XLAFAYETTEHB870AFSPLL02APTBM027LAFAYETTELM400PLL02APTBM048A0XLAFAY
ETTETELSATPLL02APTBM125A4XLAFAYETTE1800SM5107NALAFAYETTELM200PLL02APTBM027LAFAYETTE
COM-PHONE23APLL02APTBM027LAFAYETTE COM-PHONEHB650PLL02APTBM027LAFAYETTE COM-
PHONEHB750PLL02APTBM027LAFAYETTE COM-PHONEHB950PLL02APTBM027LAFAYETTE COM-
PHONEMICRO 223APLL02APTBM049LAFAYETTE COMSTATHB640PLL02APTBM049LAFAYETTE
COMSTATHB740PLL02APTBM049LAFAYETTE COMSTATHB940PLL02APTBM049LAFAYETTE
COMSTATLM100PLL02APTBM049LAFAYETTE COMSTATLM300PLL02APTBM049LAFAYETTE
COMSTAT525PLL02APTBM048A0XLAFAYETTE TELSATSSB120PLL02APTBM048A0XLAFAYETTE
TELSATSSB140PLL02APTBM048A0XLAFAYETTE TELSATSSB80GREAT UKNALAKE850GREAT
UKNALAKE950MC14568NALAKE650MM55108NNALAKE410MN6040NALAKENAROYCENALAKE5000ROYCENALAK
E5100SM5107NALAKE690MC145106NALAKE600C5121NALEAR
JETNAMB8719NAMADISONNAMB8719NAMADISON
(NEW)NAPLL02APTBM059COXMAJORM360PLL02APTBM049MAJORM540PLL02APTBM059COXMAJORM588LC71
36NAMAXCOM16E LC7136NAMAXCOM20ELC7136NAMAXCOM21ELC7136NAMAXCOM4ELC7136NAMAXCOM6EMC
14568NAMAXON40C5121NAMCE40PLL02APTBM049MEDALLION63-030RITCENAMEDALLION63-
200ROYCENAMEDALLION63-240TC9103PNAMEDALLION63-540C5121NAMIDLAND77-
106C5121NAMIDLAND77-112C5121NAMIDLAND77-114C5121NAMIDLAND77-155C5121NAMIDLAND77-
157LC7120NAMIDLAND100MLC7120NAMIDLAND150MLC7120NAMIDLAND77-101BLC7120NAMIDLAND77-
101CLC7120NAMIDLAND77-824CLC7130NAMIDLAND101MLC7130NAMIDLAND103MLC7130NAMIDLAND150M
USLC7130NAMIDLAND151MLC7130NAMIDLAND202BLC7130NAMIDLAND202MLC7130NAMIDLAND75-
790LC7130NAMIDLAND76-300LC7130NAMIDLAND77-001LC7130NAMIDLAND77-
225LC7130NAMIDLAND77-911LC7130NAMIDLAND77-915LC7130NAMIDLAND79-
265LC7130NAMIDLAND2001LC7130NAMIDLAND3001LC7130NAMIDLAND4001LC7132NAMIDLAND77-
104LC7132NAMIDLAND77-145LC7132NAMIDLAND77-145ALC7132NAMIDLAND77-
149LC7132NAMIDLAND77-158LC7132NAMIDLAND77-250LC7132NAMIDLAND77-
805LC7132NAMIDLAND77-805ALC7136NAMIDLAND2001TLC7136PTBM134A0XMIDLAND76-
200LC7136NAMIDLAND2001ALC7136NAMIDLAND3001ALC7136NAMIDLAND4001ALC7185NAMIDLAND77-
099LC7185NAMIDLAND77-162MB8719NAMIDLAND63-445MB8719NAMIDLAND79-
900PLL02APTBM027MIDLAND13-830PLLO2APTBM027MIDLAND13-857BPLL02APTBM027MIDLAND13-
882CPLL02APTBM027MIDLAND13-8888PLL02APTBM027MIDLAND13-955PLL02APTBM049MIDLAND76-
858PLL02APTBM049MIDLAND76-863PLL02APTBM049MIDLAND76-886PLL02APTBM049MIDLAND77-
830PLL02APTBM049MIDLAND77-838PLL02APTBM049MIDLAND77-849PLL02APTBM049MIDLAND77-
857PLL02APTBM049MIDLAND77-882PLL02APTBM049MIDLAND77-888PLL02APTBM049MIDLAND77-
899PLL02APTBM049MIDLAND77-955PLL02APTBM049MIDLAND77-963PLL02APTBM080MIDLAND78-
574PLL02APTBM080MIDLAND78-874PLL02APTBM048A0XMIDLAND78-
976PLL02APTBM048A0XMIDLAND78-976PLL02APTBM080MIDLAND78-999PLL02APTBM080MIDLAND78-
999PLL02APTBM080MIDLAND79-891PLL02APTBM080MIDLAND79-891PLL02APTBM048A0XMIDLAND79-
892PLL02APTBM048A0XMIDLAND78-892PLL02APTBM125A4XMIDLAND7001SM5104NAMIDLAND77-
825SM5104NAMIDLAND77-861TC9102PNAMIDLAND76-860TC9102PNAMIDLAND77-
8610TC9106PNAMIDLAND200MUPD2814CNAMIDLAND77-
856UPD2816CNAMIDLAND6001/7000UPD2824CPC833MIDLAND79-260UPD858CNAMIDLAND13-
883BUPD858CNAMIDLAND77-883UPD858CNAMIDLAND79-893 MC145106NAMIRAGEIMC145106NAMIRAGEI
IPLL02APTBM049MOCOMA45PLL02APCMA001SMONGOOSE2000PLL02APTBM049MOPAR4094176PLL02APTBM
049MOPAR4094177PLL02APTBM049MOPAR4094178ROYCENAMOPAR4094173NIS7264NAMORSEELECTROPHO
NICS 2000PLL02APTBM049MORSE-
ELECTROPHONICS3005ROYCENAMOTOROLACF925AXSM5104NAMOTOROLAT4000ASM5104NAMOTOROLAT4005
ASM5104NAMOTOROLAT4009ASM5104NAMOTOROLAT4010ASM5104NAMOTOROLAT4020ASM5104NAMOTOROLA
T4022ASM5104NAMOTOROLAT4025ASM5104NAMOTOROLACM540TC9103PNAMOTOROLACT950AXTC9105PNAM
OTOROLACB550TC9105PNAMOTOROLACB555TC9105PNAMOTOROLACH550LC7136PCMA002FMUSTANGCB1000
LC7136PCMA002FMUSTANGCB2000LC7136PCMA002FMUSTANGCB3000L7136PCMA002FMUSTANGCB3001LC7
136PCMA002FNATO40FMPLL02APCMA001SNATO2000NDC40013NANDIPC200NDC40013NA