nEYE PC DVR User Guide PDF

DVR User Guide v1.
0
Rev. 2.0
September 2006
Model [SDC SERIES, SDR SERIES]
Service of New Technology

Table of Contents
1 BEFORE START ....................................................................................................................1
2 PRODUCT OVERVIEW........................................................................................................5
2.1 SYSTEM COMPONENTS .......................................................................................................5
3 SYSTEM OVERVIEW ...........................................................................................................6
3.1 SYSTEM FEATURES .............................................................................................................8

3.2 MAJOR FUNCTIONS OF DVR SYSTEM ..............................................................................10
3.3 DVR RUNNING ................................................................................................................10
3.4 INITIAL DVR OPERATION ................................................................................................. 11
4 MAIN WINDOW ..................................................................................................................12
4.1 INSTRUCTION ON MAIN WINDOW ....................................................................................12

4.2 SCREEN LAYOUT (SCREEN DIVISION BUTTONS)...............................................................13
4.3 AUTO-CHANGE & FULL SCREEN ......................................................................................14
4.4 MAIN WINDOW TIPS ........................................................................................................14
4.5 HOW TO USE <AUDIO>.....................................................................................................16
4.6 EXPLANATION ON FUNCTION BUTTONS ............................................................................17
4.7 PTZ CONTROL .................................................................................................................21
4.8 QUICK SEARCH ................................................................................................................25
4.9 BACKUP ...........................................................................................................................28
4.9.1 Manual Backup .......................................................................................................28
4.9.2 Schedule Backup .....................................................................................................31
4.9.3 AVI Backup..............................................................................................................33
4.9.4 Direct Backup..........................................................................................................34
5 ENVIRONMENT SETUP ....................................................................................................39
5.1 SYSTEM SETUP .................................................................................................................40

5.2 RESOLUTION SETUP .........................................................................................................45
5.3 CAMERA SETUP ................................................................................................................46
5.4 SETUP RECORDING SCHEDULE .........................................................................................49
5.5 NETWORK SETUP .............................................................................................................52
5.6 NETWORK II SETUP ..........................................................................................................56
5.7 SENSOR AND RELAY SETUP ..............................................................................................58
5.8 USER ................................................................................................................................61
5.9 SYSTEM INFORMATION .....................................................................................................64
6 HOW TO SEARCH ..............................................................................................................65
6.1 HOW TO SEARCH (INCLUDING AUDIO SEARCH) ...............................................................66

6.2 MULTI -SEARCH ...............................................................................................................68
6.3 GROUP-SEARCH ...............................................................................................................68
6.4 HOW TO USE <BOOKMARK>.............................................................................................69
6.5 PARTIAL ENLARGEMENT SEARCH .....................................................................................70
6.6 PANORAMA SEARCH .........................................................................................................72
6.7 PRINT ...............................................................................................................................74
6.8 SAVE IMAGES AS JPEG/AVI FILE .....................................................................................75
6.9 IMAGE ANALYZING ..........................................................................................................76
6.10 SAVE THE IMAGE AS <AVI> FORMAT FILE .....................................................................79
6.11 MOTION SEARCH..............................................................................................................79
6.12 IMAGE QUALITY CONTROL ..............................................................................................81
7 WEB-DVR .............................................................................................................................82
7.1 TO REGISTER <WEB ACCOUNT> IN <AUTHENTICATION SERVER ......................................83

7.2 NETWORK SETUP IN DVR (SERVER NOT RDVR) .............................................................86
7.3 HOW TO USE WEB DVR...................................................................................................87
7.3.1 To Monitor Live Video (images) ..............................................................................88
7.3.2 How to <Playback> (Remote Search).....................................................................91
8 APPENDIX ............................................................................................................................94
8.1 HOW TO REINSTALL DVR S/W. ........................................................................................94

8.2 OPEN(REMOVE/UNLOCK) FREWALL IN WINDOW XP 제..................................................95
8.3 WINDOW DISPLAY SETUP .................................................................................................96
8.4 HOW TO USE CD FORMAT TOOLS IN BACKUP ....................................................................97
8.5 AVAILABLE PROTOCOLS ACCORDING TO COMPANY AND BRAND. .....................................99
8.6 FAQ ............................................................................................................................... 102
8.7 H/W CONNECTION WITH EXTERNAL DEVICES ................................................................ 104
Manual History
Date Revision
April 1, 2006 VER 4.3.0.1 Release AND ADDED FUNCTIONS
September 8, 2006 VER 4.5.0.0 Release AND ADDED FUNCTIONS
October 20, 2006 VER 5.0.0.0 Release AND ADDED FUNTIONS
DVR User Guide Manual
1 BEFORE START
N.B points before installation
Please read with care before DVR installation. This will save precious time and energy
to learn and study important points to install and run Servntec DVR. For users who are
already used our systems, please read this again with care.
And let’s start DVR …with this Manual.

What is DVR? DVR stands for DVR (Digital Video Recorder), which
transform analogue image and audio data to
(Digital Video Recorder) <Digitalized> data and records and save these data in
HDD. This High-End system cut the old VCR system’s
cost and labors, and gives all users to access saved
data by easy and simple <Digital> data system in
anywhere and anytime by Network.
Intellectual rights and properties , and Trade Mark

Neteye is the Brand of Servntec’s CCTV SYSTEM, which is protected by Law in
Korea and international markets. And illegal copies of this Manual and S/W are
prohibited by the international and Korean Law.
About Company
one of leading companies in Korean DVR industry, we have
focused in developing and supply high quality and market oriented DVR(Digital Video
Recorder) and IP products and surveillance solution from the establishment.
All Tech staff is consisted experienced engineers , who have more than 10 years in
DVR industry, and we all Sales and Tech team are integrated and making efforts
together to lead Market Needs and Trend, and more to make new innovative products
and services.
Briefly, our company name <n-EYE> stands for “Service of New Technology” ,
which shows our will to <make service> to our partner and customers with <new
technology>. Our Motto are below
1. Develop and make new products according to Market Needs, and lead the new wave.
2. Manufacture and supply High Qualified and most stable products
3. Based on Trust and Partnership, give full technical and satisfied A/S.
Sales Department
Overseas
Tech Support
Tel, Fax
Web Site
User Guide v1.0 Page 1

Revision 2.0 September 2006
Check Points for installation

1) Place the systems on flat and dried place after unpacking, where has good
distance between the back of system and wall (15 cm), and note that this place has
to be good ventilation area.
2) Please avoid the place where has strong electromagnetic waves

(like Speaker and Amplifier).
3) Please avoid the area where has direct rays of sun and heating to
protect systems which is very sensitive to lighting and heat.
4) Pease avoid place where is directly open to low temperature of

outside.
5) Please pay attention not to get damage by tools and other devices in
the installed place.
6) Please avoid the place where has high vibration or temperature or

humidity.
7) Please check the power voltage before connecting power.

(The default voltage setup is 220V. So in the nations where use 110V,
please change this to 110V by switcher in the back of system)
8) Please throw vinyl pack cover in the safe place or waste bin, where
children can not touch. This vinyl can be dangerous for children to
play and use with.

N.B Points to use

1) When users pull integrated system apart by themselves, users can
not get full maintenance services and A/S from supplier. So please
contact the supplier first in malfunctions.
2) Please study the manual first before operating DVR.
3) Recommend contacting supplier or Servntec’s support team before

dismantle system or manage by users.
4) Please do not handle consent or power lines with wet hands.
5) Please connect power lines to consent correctly.
6) Please do not use thinner, Benzene, or alcoholic matter as cleaner.
7) Please keep away from the extended terminal.
8) Please shut all program and S/W before Power Off.

(When users can not shut down power, please use Power Button in
the front of system)
9) Please keep the system away from Magnetic Matter, and place it in
the place with good ventilation.
10) Please do not dismantle or maintain the system without discussion

with Expert or supplier or Servntec support Team.
11) Please do not put heavy things on the system.
12) Please do not move the system while system is running.
13) When users detect some smoke or scorching stinks, please shut
down the system immediately and contact the supplier or Servntec
support Team.

The available warranty for free change is 1 year.

(When these malfunctions are caused by users
Warranty
mistake or natural disasters, this warranty is not
available)
[ The Cases when warranty is not applied ]
1. System Shut Down by users’ mistake.
2. Careless using which is not based on Manual Instruction.
3. Irregular Power Using which is not based on Manual

Instruction ,
4. Warranty is not applied to the consumption components change and

cleaning.
5. Malfunctions caused by system maintenance or dismantling while

No-licensed persons’ handling the system.
6. Though the warranty is over, upgrade and maintenance service

are available with minimum cost , please contact the supplier or
Servntec support team.

2 Product Overview
2.1 System Components
DVR Full Set Configuration
Please unpack a system in flat and not wet place. Please check all components are in
the package.
DVR system case (1SET) Power cable / System Open KEY

Users Manual Rack Handler/Screw
Installation CD
-Manual
-Driver
-Setup S/W Key Board / Mouse
OS License Label (Windows XP or 2000 )

Components can be changed according to option selection.
DVR Kit Configuration ( DVR board and Option)

- Program CD (DVR, Driver ) ※ Please note that KIT configuration parts
-Capture or Live Board could be different from Set.
(Extension BD)
-Camera/Audio/Extension Cable
- Option according to Model

3 System Overview
What is DVR(Digital Video Recorder)? DVR system transform the analog video and
voice data into <Digitalized> ones and stores on a storage device (HDD or
Others), and allows users to search by any criteria they specify, and to make
users can access the data through a network in anytime and anyplace.
This is commonly known as the DVR(Digital Video Recorder)
DVR in <Wikipedia… www.wikipedia.org >. Please read more on this.

Digital Video Recorder (DVR) (or personal video recorder (PVR)) is a device that
records video without videotape to a hard drive-based digital storage medium. The term
includes stand-alone set-top boxes and software for personal computers which enables
video capture and playback to and from disk. Some consumer electronic manufactures
have started to offer televisions with DVR hardware and software built in to the television
itself.
[Pic DVR vs RDVR Configuraiton]

[CCTV System Configuration using 3 DVRs ]

1. DVR System: DVR stores digitalized video and voice data, users can access
these data simply and easily (Search/Live Monitoring/Backup).
, Sensor & Relay Control, Watch-dog(Self-Diagnostic Tool) support.
2. Authorization Server : This support fixed and dynamic IP, and make authorized Web
Account can access and manage DVR monitoring.
This server SW is supplied freely by Servntec.
( However users want to build separate server, users has to setup their own by their own
Equipment and Server SW)
3. RDVR: This supports Remote-Monitoring, Remote-Search, and Remote-Setup and 2
Way Audio Setup.
※What is <RDVR>?
RDVR mean <Remote DVR>, which is commonly called RMS (Remote Management
SW). With this, users can access DVR in remote areas through Network without any
barrier of <Time and Space>. Main functions are Remote-Monitoring, Remote-Search,
and Remote-Setup and 2 Way Audio Setup.
When users install this in any PC, users can access DVRs with ID address and
ID/Password. (Please note RDVR supports Multi Connection , it is called as <Group
User>)

3.1 System Features
DVR System Main Features

-Development and testing in R&D center and Fields over
6 years
-More than 20 times upgrading
-Field Tested Release
Stabilized System
(Our all SW is pre-tested and distributed in our partner
company before official release)
-Strict internal Testing and Q/C.
-Optimized System Load (CPU, Ram Usage Low)
-More than 20000 copies are distributed, tested , and

Field Testing verified in global market.
and Distribution -Continuous feedback and support in Tech and Service
terms.
- Independent Data storage area apart from OS
running area (EX, OS:C, Data :D)
-Saving the data as Servntec’s original <Image
Efficient File System 1
DB> (100MB)
-Unique and powerful Recovery Tools
(Data file system recovery and search)
- In D1(720*480/720*576) Resolution, De-interlace filer

can be used for Highest Image Quality in Search.
-Various Search Ways
Outstanding Image Quality (Search, Multi-Search, Panorama Search, Enlargement
Search)
-100% synchronized Audio Search with Image
1
<ImageDB> is unique way of Servntec file system to save the data in HDD, which
has effective data array , fastest data processing system with lowest using system
resources. Moreover it has strength in protecting data safely.

- User friendly and Intuitive GUI

-Various Screen Display Layout, and easy Video, Image,
Simple and Easy GUI Quality, and Sensor and Relay Control and Managing
-Easy Network Managing and Control
-PTZ 제어(Preset, PTZ Touring)
- Remote Live Monitoring, Save, Search, Transmission,
Control through Network
Support Various Network -2 Way-Audio
Environment -Support PSTN(ISDN), XDSL(ADSL,VDSL)
(Connection with RDVR) - Authorization Server(Fixed, Dynamic IP)
Site Management and Remote Search and AVI
backup by IE (Internet Explore)
- Various Backup: Manual, Scheduled , AVI, and Fast
Backup
Enforced Backup
-Direct backup in File system
(Move, copy and paste)

3.2 Major Functions of DVR System
Major Functions
Max 16 cameras, Real Time Live(30fps per Channel) Monitoring and Recording
Various Range of Recording, 30 ~ 480 fps according to Board Model in MPEG-4
compression
Individual Setup compression rate and Recording fps per camera (channel)
Stable and Unique <Basket> file system: Using unique <Basket> storing system
(100M), it offers the most stable Recovery and Backup system
2 Way-Audio
Connection with RDVR, users can Live Monitoring, Search, Setup though Network
(LAN, PSTN, ISDN Environment)
Easy Backup and Search System to various Backup Media
(DAT, DVD, ADR, DLT, CD-RW, On-Stream)
Various Search Method: Event, Motion, Panorama, and Minute Search, Jog-Shuttle
Search, Camera Combination Search (Multi Search)
System Watch Dog Function: Using this (Watch Dog-H/W and S/W), the system
recovers automatically when detecting some problems.
Remote Notification (Email, SMS): Users can notify g the DVR using E-mail and SMS
notification, and moreover monitoring them by RDVR Event Viewer
Search and Recording with Sound (Audio)- In Main Window Search and Recording
Setup
Individual Account and Password Setup( Multi-Level Password ) , which makes each
users different level setup
Various Alarm and Sound Setup
(Beep Sound, Motion Area, Enlargement, Email sounds setup )
3.3 DVR Running

Instruction on DVR operation: When power on, DVR starts automatically
Our DVR runs on GUI(Graphic User Interface), users can run all functions by just
double clicking Icon(Button) on window .
When moves the mouse cursor to each Icon, users can see each Icon’s function
description

To use all the function of system, users have to unlock <Key Lock> firstly. This can be
done by passing ID and Password authorization. To prevent any problems,
users(administrator) have to setup <Key Lock> function.
3.4 Initial DVR Operation

Instruction on Login process
<Key Lock> is setup to prevent unauthorized operation and setup
Description
changes, so users have to setup <Key Lock>
Default Setup
< ID : admin / Password : 1111 >
Enter ID/Password and Click! ※Can use Virtual Key Boar.

<Key Lock> is used and useful in below cases
- When making initial file system (and adding HDD )
-Changing Setup values / -Independent <search> / -Independently playing
<AVI Recorder>
※This depends <User> Level Setup
※To secure the system, please change the default ID, Password in initial Operation.
System Watch-Dog is not setup as default, so users have to check and run <Watch-
Dog> function in initial operation.
In initial operating, users can hear <beep> sound, which is almost caused by camera
disconnection. To stop this, please connect cameras or just double click each
camera channel.
(Not using this

Channel)
(Video Loss :Beep)
When system shut down abnormally, <File System Analyzing> message will be shown
to check the system safety. Please note this. 다.
When some buttons are not active, which mean that system model does not support
those functions, so it is normal.

4 Main Window
Overview
This chapter gives the instruction on how to control and use functions and
buttons in DVR main Window.
4.1 Instruction on Main Window

In the main window, users can control, monitor, manage all the video data like Screen
Layout (Display Channel Split), video signal, sensor, and relay, and live audio.
Channel Name Date, time/Connection Status Recording Information
1 [M] Office 1 [P][A]

[P][A] 2 [M] Park [P]
Lock Button
Setup, search, PTZ,
Fast search,
Backup
3 [C] Office
Screen Layout (1~16ch)
Move Page
Auto-Change
Full Screen
Exit
Logo Audio, Alarm, Relay Status and control Live Audio, Alarm, Relay, Image Quality Control

4.2 Screen Layout (Screen Division Buttons)

The table below is the instruction of Icons(buttons) for changing screen layout(Screen
Division)
Screen Layout
To select the screen division users want by just clicking button
Screen division Type: 1(Full),4(Quad),6,9,10,16
Screen Layout
※To setup initial Screen Division (the first screen division when running
Buttons
DVR), users can setup “Setup-System-Initial Screen-Screen
Split(Division)”
How to change and select Layout
1 4 6 Select wanted Screen Division

Step1
Before selecting
9 10 16
1 2 6 When clicking
Step2
After clicking
9 10 16
Previous Screen & Next Screen
Show the previous channel (in one channel) or previous
Previous screen division (in 4 channels or others)
EX) When users see camera 2 on full screen, it goes to
Screen camera 1. When seeing 5~8 (Quad Mode), it goes to 1~4
(Quad Mode).
Show the next channel (in one channel) or next screen
division (in 4 channels or others)
Next Screen EX) When users see camera 1 on full screen, it goes to
camera 2. When seeing 1~4(Quad Mode), it goes to
5~8(Quad Mode).
※According to used Board Model, some buttons are not active.

(Ex, When using 4ch Board, 6, 9, 10, 16 screen layout icons are not active.)

4.3 Auto-Change & Full Screen

Auto Change
It shows next channel or screen division automatically when clicking
this.
※ In 16 channel mode, it is not active. Because is shows all channels
in 16 channel screen.
※When using this with <Full Screen>, users can monitor each
channel on full screen.
Full Screen
Show one channel (camera) on full screen.
When double clicking this, previous screen will be shown.
4.4 Main Window Tips Instructions for <Full Screen> in Main Window, and Virtual
Display function.
TIP 1: 1ch on Full Screen

When double-clicking any channel in screen, clicked channel becomes
Step1
<Full Screen>.
When double-clicking <Full Screen>, it becomes to previous screen.
Step2
How to use Mouse
-Main Window Double-Click left button of Mouse :Full Screen & Previous Screen
Double-Click left button of Mouse: 1ch Full Screen &

-Full Screen Clicked channel Full Screen
Full Screen & Previous Screen: Goes to previous Screen

TIP 2: Channel Selection by Camera Button

When clicking channel button like the Pic of TIP 2 below, clicked camera will
Description
be shown on <Full Screen>
Step1
Select the channel like above Pic, users want to see on <Full Screen>
Selected channel changes to <Full Screen>.
Step2
※ This only acts on 1ch screen division
TIP 3: Virtual Display Matrix

It gives the users to make the camera combination (channel selection)
Description
easily and simply just by Drag & Drop.
When users wan to move
<ch2> to <ch1>, just Drag
& Drop that camera
<ch2> to the position of
<ch1>.
Instruction
※ It is the 1:1 position

change.
※ This does not influence the recording; it just changes the position shown in the Screen
Division. It is Virtual Display Change.

4.5 How to use <Audio>
Audio(Sound) Button
Instruction Users can check and monitor <Live Sound>(Audio) in monitored place.
Audio Setup
Step1 Click Setup button
Enter ID/Password for <Login>.
※Default
Step2
-ID: admin
-Password: 1111
1. Click <Resolution> Tap.

2. Select channel(camera) in “Camera Selection”
3. Select(click) Audio No connected to that channel

Step3 4. Check in the box “Audio Use”
5. Check in the box “Live Audio ”
(Unless checked users can not hear the Live Sound(Audio) in Live
Monitoring)
6. Check in the box “Audio Save”
(Unless checked, Sound is not saved with Video)
※ Please leave Audio Volume as <Default>. After “Test”, please change
when Sound is not clear or good enough to hear.
To change <gain> value, users have to use Microphone directly in
the monitored place( gain ‘0’ means <No Compensation in Sound>)
Step4 Click <Apply> – <Confirm> button

Hear Live Sound (Audio) in Main Window

Give the instruction to get <Live Sound> with Video in Main Window
Description
※To hear <Live Sound>, users have to setup like below
Step1 Click Audio(Sound) icon in Main Window
Step2
Users can see available <Yellow> channel with <Audio> which is setup in
each channel
When clicking ch 1 button, it changed to
Step3 <Red> and can hear <Live Audio>. When
one more click, the <Live Audio> is off
When Clicking <Audio> icon one more, <Audio> function
Step4
becomes off.
4.6 Explanation on function Buttons
Sensor Icon
Description
This icon shows <Sensor> Status connected to DVR.

Violet : The Status Sensor is connected
Instruction
Grey : <Sensor> disconnected

Relay Icon
Description
This shows the <Relay> status connected to DVR, and it makes users to
manage <Relay> connection (On/Off) to DVR.
Green : <Relay> connected
Instruction Grey : <Relay> disconnected
※ When users click these buttons, users can control On/Off.
Image Quality Control Button
Users can control the image quality control by using these buttons.
Instruction 1) Brightness Up/Down: Can control Brightness Values of Video

2) Contrast Up/Down: Can control Contrast Values of Video
3) Saturation Up/Down: Can control Saturation Values of Video
4) Hue Up/Down: Can control Hue Values of Video
※In the bottom of channel, users can see the Value of each. Users can
control the values seeing this.
Image Quality Control Button 2

When users want to apply this value to all channels, users can use this.
When users wan to change all values to <Default> values.

Video Control Buttons
Description
It shows the Camera connection/disconnection status, and camera

<usage> status.
Blue : Normal Connection
Instruction Red: Camera Disconnection(Setup to used but Disconnected)
Grey : Do not use <Camera>
Camera(Channel Display) Information
Camera NO : Shows camera No in that channel
Recording Status: [N]No Recording, [C] Continuous Recording,
[M]Motion Recording, [S] Sensor Recording, [C&E]Continuous & Event
Recording, [S&M] Sensor & Motion Recording
Camera Name (Description) : Shows the Name of each channel
Instruction PTZ Connection: When PTZ camera is connected and setup, [P] is
shown.
Audio Connection: When <Audio> is connected, [A] is shown.
Red Border Line : When Event is setup in each channel, it shows
<Red Border Lin> in that channel
Information Window
This shows the Data/Time information
Date/Time
[Network Connection Icon]
It show currently connected system information, when double-click, it shows
information.

Recording Data Information

Recorded Data: It show the <Oldest
Recorded Data> Time, which mean from that
Description time <Record> started until Current Time.
(Ex 2006.8.29:11:37 is the start time of Recording which is saved in HDD
until current date/time)
Icons Description (When click this, users can enter each Mode)
Setup Icon
Search Icon (where you can search and play all recorded data)
PTZ control Icon
Quick Search Icon, where you can search quickly the recorded data in Main
Window without entering to Setup Window
Backup Icon

4.7 PTZ Control

PTZ Setup
Description When entering this, users can setup PTZ cameras
PTZ Control(Setup Mode)
Step1 For PTZ setup, just click <Setup> Icon
Enter ID and Password for <Login>
※Defualt ID: admin
Step2 Password: 1111
Step3 Select and clicking channel (camera), in camera <Tab>
Step4
In PTZ Setup click “Setup”
Step5
1. Select camera in <Camera Selection>

2. Check <Use> in <Receiver Setup>
3. Select Port (Com1 or Com2)
4. Select PTZ camera <Protocol> to use.
(When Selecting <Protocol>, other setup values are setup automatically)
※If there is no protocol in the list for wanted cameras, please contact
Servntec for adding them.
Step6 After <Applying>, please check the normal running

PTZ control in Main Window

Users can control PTZ in Main Window
Description ※ For this, users have to setup previous pages PTZ setup in each
camera.
Step1 Click PTZ control Icon
1. Select channel No, just clicking left/right(◄ ►)

button.
2. Control using below buttons
[Control Buttons]
(From the Camera Power Button)
-Camera Power On/Off
Step2 -Camera Light On/Off
-Auxiliary Power On/Off
-PTZ Direction Control Panel
-Auto-Pan On/Off
-PTZ Camera Selection
-Focus/Zoom Button
-Preset Setup Button
-Touring Setup Button
After checking the movement precisely, if users can not get right
movement, please check again below.
Step3
1. Selected PTZ camera is in the List to support or not
2. Right Protocol 3. PTZ camera H/W connection 4. Power
N.B points
※According to PTZ camera brand and model, the functions can be applied partially;
please check the protocol and camera brand and model.
※ Receiver ID has to be connected to DVR Camera NO.
※ The PTZ camera model not in the list, please contact Servntc suppot team

How to setup PTZ Preset

Description PTZ preset makes users setup PTZ cameras to move as setup
position for monitor the wanted place.
Preset Icon When setup, the <Yellow>(Before Clikc) flag changed to Red(Click).
※ According PTZ Receiver model, there is some model not to support
PTZ. Users have to check this first.
※TIP: Before setup, users have to check the place where needs Preset
function.
Step1 Click PTZ Icon, and select channel.

.
Step2
1) Move the camera to wanted place.

2) Enter Preset No/Description.
2-1) In the 2) step, if users check <Sensor Used> box, the camera
moves to Preset position when detecting Sensor automatically. (N.B:
Check <Sensor Used> box, Select Sensor No)
3) Apply and save this after clicking <ADD> button.
4) Users can add presets making same procedure (1~3).
5) Have to save Setup Preset just clicking <Save>
※To check normal setup, users can check just clicking <Go Preset>
button before <Exit>.

How to setup <Touring>

Description <Touring> Icon makes cameras move to the places for wanted monitoring.
When setup, the <Blue>(Before Clikc) flag changed to Green(Click).
Touring Icon
Step1 Setup several <Preset> first.

1) Enter <Tour No> and
<Description>
2) Move registered <Preset> to <Tour
Member> clicking >>.
3) Set <DW(Dwelling time)>
※When set this as <5>, the preset
Dwelling time is set as 5 seconds.
Step2
4)Save …clicking <Save> button
5)Setup wanted several <Touring>
just making the same 1)~3)
procedure.
※To change this users can modify

this using <ADD/DEL/Save/Modify>
buttons.
To test normal <Touring>, use <Go Touring> and <Exit>.
To Stop the testing, click <Stop Touring>
Step3 ※When users use PTZ and Dome camera with <Preset> Receive ,
however, when using several PTZ cameras at the same time, users can
not use <Touring>. This is because our <Touring> is done by S/W

4.8 Quick Search
How to use Quick Search

<Quick Search> is made for <easy and quick> search in Main Window
Description
without entering <Search> mode when users needs urgent search.
Users can check and see <System Log> here.
※ For more specific search, use <Search> mode.
1. Click <Quick Search> Icon.
Step1
2. Select searched items (Event).

[ 1: Motion , Sensor Event (And/Or) ]
[2: System, Video, Network, Notify Log(And/Or) ]
3. Enter searched period(Date…Check) (From~ To~)
4. Click <Search>!!!!
After clicking, users can see the result in the filtering values. When clicking
searched one in the list, users can see the Video in left area. When
clicking <Play> button, users can search and monitor the data.
Step2
※ Users have to check in <Use Event>(sensor and motion) and the
<System> tab in <Setup to get Event log files and search them in
<Quick Search>.

Backup(Save) as JPEG file

1. Click Backup Icon
Instruction 2. Select Backup Folder
Backup Icon 3. Click <Save> button

※The file name Is made
automatically, but users can
make it as wanted.
Print
1. Click <Print> Icon. (??)
Step1 2. Enter the <description> of
인쇄버튼은? image.
1. After checking the Print Page

with Image (like left), and click
<Printing> button.
Step2
※For this, users has the Printer

setup with DVR.

Search
Result by
Main/Video/N
etwork/Notify
Log
In the list, users can see all the applied log file (Main Systems Power On/Off, Video Loss,
Re-Setup values). And more users can check the log files for access log and setup change
through Network, and Notifying History, which will be very useful for monitoring all events
and system access and setup changes.

4.9 Backup
There are 3 kinds of Backup for Manual, Schedule, and AVI backup. Moreover users can
backup all data file directly just identifying the Backup Date.
4.9.1 Manual Backup

How to Manual-Backup
Users can use this to backup the data recorded in specific
Description
camera, time, and minute period with Audio.
※ It is recommended to backup the selected data (based on time, min, or specific filtered)
※Available Media: HDD, DVD, DAT, CD-R/W, MO, ZIP, Network Driver
※When using some Backup devices, users have to use specific S.W which is supported by
a device, in this case users have to install this S.W in the system. More users have to
format this media first(CD-R, CD-R/W, DVD) before backup
Step1
(Backup Window)
Click Backup Icon
Setp2
(Select Backup Data)
-Date
-Channel
-Time
-Minute
Select the data by Camera/Date/Time/Minute by just Checking
※Select this one by
Box
one

1. Select the Drive to Backup
Step3
(Select the folder to
save or backup)
2. Select folder and make <New Folder> if needed by clicking
right button of mouse like above Pic.
※The default Name of New Folder is < Backup Folder>.
And after that…new folder names are Backup Folder(1),
Backup Folder(2)…
※To format ODD(Optical Device Disk) , please use <ODD

Format>. Users have to setup <ODD Tool> in advance to use
this.
Step4 Click <Run Backup>
Step5
Above message is the final confirmation for Backup, when click

<Yes>, the selected data is backup in selected folder.

Step7
(Backup done)
When Backup is finished, users can see <Backup Success> log

in <Backup Log View>.
※In selected backup folder, users can see the data in <Backup
Folder>.
※ To see this, users have to use <Backup Viewer>.
How to select(designate) CD format tool

1. In the <System> tab in <Setup>, select <ODD Tool>.
2. Select format tool after clicking <Search> button.
- There are tools (S/W) like DirectCD(Roxio), InCD (Nero)
3. Select format Tool, and click <Open> and exit.
Instruction
※ Tip for Backup

Backup using Media, users have to format Media(CD-R, CD-
R/W, DVD) in advance, please refer to previous chapters.

4.9.2 Schedule Backup

Schedule Backup (Auto-Backup)
Users can make automatic backup using <Schedule Backup> to
backup the data in setup date/time for selected data..
※When backup Drive space is not enough to save all selected

Description data, <Not Enough Space> message will be shown.
※Users can not use <Schedule Backup> and <Concurrent
Backup> at the same time.
※To run Automatic Backup, <Start Schedule Backup> has to be
active status..(Please check the Icon in <Tray Bar>)
※When <System> restarts, <Schedule Backup> runs
automatically.
Run Schedule Click <Schedule Backup> in <System> tab in <Setup>.
Backup
Initial Window of
Schedule Backup
[Automatic Backup
Type]
1. Schedule Backup
(Selected Period
Backup)
2.Concurrent
Backup
Selected Time Backup (Including Full Backup )
Step1 Check in<Schedule Backup>
1) Click <Select> button and select Backup Drive.
2) Check in <Use Auto Deletion> button.
Step2
※<Auto Deletion> is <auto-delete the oldest data when selected
Drive HDD space is full, and overwrite data>
Select <Backup Type>.
Full Backup(24 hours) Selected Time Backup
(Backup the data from Start to
Step3
End Time)

Step4
(In Full Backup) Select <Start Backup Time>.
(Start Time for <Schedule Backup> is done for the first time)
Select <Start Date>

Step5
(From the data of this time, data is Backup automatically)
※When users Setup like Step4,5, users backup all the data from
2006.10.15 to 10.17 for 2 days.
Click <Confirm> button and Exit
※ When Backup is done by <Schedule Backup>, users can see
Step6
this by <Backup Viewer>.
※To use <Concurrent backup>, Schedule Backup(including Full Backup ), users are
recommended to use Big Size HDD after calculation of selected data Size. This is done
by once in a day.
Concurrent Backup
<Concurrent Backup> is the system to backup the data at the
same time when data is saved in HDD. Briefly speaking, our
system saves the recorded data in selected HDD Drive (normally
Description in D:) as <ImageDB>, so when users use <Concurrent Backup>,
users can backup this recorded data in selected HDD drive at the
same time as <ImageDB>.
1. Check in <Concurrent Backup>.

2. After clicking <confirm> and Exit, it automatically starts
Instruction
<Concurrent Backup>.
※With <Backup Viewer>, users can see backup data.

4.9.3 AVI Backup

AVI Backup
Users can save the video as <AVI> format file. To see this, users can
Description
easily monitor the AVI file by Window Media Player.(Over Ver 9)
There are 2 ways to run.
-1: Click <Save> button in the search mode, click <AVI Save> Button.
Instruction -2: Run Start-Program-DVR-<AVI Recorder>
※ When users want to run <AVI Recorder>, users have to enter
ID/Password for <Login>
Step1 Initial Window
Sequence
1. Select Channel
2. Set Start Time
3. Set End Time
4. Click <Auto
Sync> for Audio
Synchronization
Step2 5. Select Saved
Folder
※<Auto Sync> (Automatic Synchronization with Video) helps to make AVI

file with selected data’s fps automatically, so it gives user right recorded
fps for AVI saved data. If those data are recorded with Audio(Sound),
<Use Audio> box check in automatically.
※Saved folder and name are automatically made, however, users can
change them as users want.
Step3 Click “Start ”button and save AVI file
Step4 Click “Close” button and Exit

[AVI File Play] Using Window Media Player, users can play backup AVI File just double-
clicking when WMP is installed in the system.
4.9.4 Direct Backup

Direct Backup
Users can backup the data at the same speed as PC Copy Speed,
Description
However, users can not search for the data before Backup.
Click the right button on the<Backup>
Icon like left Pic over the <Task Bar>,
and select <Direct Backup>.
Instruction
1) Select data to Backup based on

Recorded Tie
2) Click <Backup> button to start
※YMD/Record Start Time~
Step1 YMD/Record End Time for all
channels. So users can backup all the
data based on this information.
※Shift(Select All), Ctrl(Select several
data)
Step2 Click <Backup> and select folder to save
After success Backup, <Backup is

finished> message will be shown
Step3
※Please check the backup folder (Ex,
20061017) in saved folder
※Users can see this by <Backup Viewer>

Manual Data File Backup (Files Copy)

※ Please be careful in using this Backup, it is recommended that
Expert or Manager use this in urgent case like HDD problems.
It is very similar like <Direct Backup>, but the only difference is to

backup manually <ImageDB>.
Description
[Please use this in below cases]
-HDD problems!
-Users have to replace systems when some systems have a problem,
and have to backup HDD in troubled system.
-Manager need this.
Instruction 1. Open <Window Explorer>

2. Search <Neteye> folder in <ImageDB> made directory
3. Select Files to copy in <NETEYE> folder
4. With Shift, Ctrl key (like Window), or <Drag & Drop, users can
select the files easily to copy.
-Have to select <Image file and index > together as a couple
(Ex, WS000017 / WS000017.idx )
4. Copy them to ….
(Please copy this not <move>)
※Users can see backup data with <Backup Viewer>.

4.10 Backup Viewer
How to use <Backup Viewer>

Use <Backup Viewer> when monitor and see <AVI Backup>, <Manual
Backup>, <Schedule Backup>, <Direct Backup>, and <Files Copy by
Description
Manual>
※Window Media Player can be used in <AVI backup> playing as well.
Run 1)Start => Program => DVR =>Backup View
Instruction Run 2) Run Backup Viewer directly.
C:\Program Files\DVR\BackupView.exe …Just Double-Click
Users have to search and designate
the Backup folder exactly. When
finding, click <Confirm> button.
Step1 ※Left Pic shows the image when

clicking <search> button in
<Backup View> S/W.
For <Manual Backup>, users can see backup data directly on <Backup
Viewer> without Step 3.
Step2 ※For <Schedule Backup>, <Concurrent Backup>, and <Direct Backup>,
and <Manaul Files Copy>, users have to <Recovery> Process (Step3)
to see the data by <Backup Viewer>
Step3
Select ‘Data Conversion’ button
※This <Recovery> procedure needs, because in the backup process the

data is saved as <Dat file> to save the backup time. To see this users
have to <recover> this to see this

Step4
Data Conversion status Conversion finished
3
Step5 2
1. Click <Yellow> date (which has the recorded data) in the calendar.
2. Search the recorded data by camera, time, and minute.
3. <Play> the searched data(by clicking <play> button in 3)
When users want to search other <Backup> data, users can search this by
just clicking <Search> button (like left Pic) and do the same procedure
(Step1~4) and monitor.
※ Users have to <install Backup Viewer Package> to see backup data in
another PC (system)
※In above case, when Date form is different in DVR PC , users have to
N.B change the date form the same as DVR PC. Please note that Backup
(Red are folder follows the PC DVR date from
most FAQs) (EX. When PC DVR date form is YMD, and another PC is DMY, users
can not play Backup files….users have to change date form YMD (it is
backup in another PC in the date form DMY)
※When the <Backup Drive> is different in <Backup PC> and <Backp Play

PC>, users have to make it as the same. And users have to <recover>
this even if <Manual Backup>.
※When users backup to <CD> in the <Easy CD Creator> installed
PC,users have to user have to install proper S/W like UDF Reader.

5 Environment Setup
The environment setup is used to configure main system operation functions like
Monitoring, Recording, Search, Backup, Sensor and Motion Detection, Relay
control and Network. Users can setup all functions based on users’ situation and
need (Operation Time, Recording time, Event Scenario).
Please note the following information.
The setup menu consists of 9 tabs. When you finish operation for each tab, click
the “Apply”
” button before moving to the next tab.
When the system detects a failure, the watch-dog function reboots the system in
specified period of time with the beep. The system is not configured with this
function in the warehouse. Check the watch-dog setup column to use this function.
If the beep is configured to work with event signals, which are different from the
watch-dog function, the beep may be generated. For your reference, the system
generates the beep when the camera signal is disconnected.
Some functions automatically reboots the system when selected. These are available
only after the system rebooted.(Change NTSC to PAL system)
Only four cameras are configured to constantly record the images in the warehouse.
Setup the schedule, and the condition to record and use cameras as required by the
field..
Click the “Apply” button after configuring each tab and click “OK” to complete the
setup process. Then, following window appears in the monitoring screen and the
screen starts to blink within approximately 5 seconds while initializing the hardware
and software

5.1 System Setup
System Setup
Camera Type : Select the NTSC or PAL (When changing, it applied after
rebooting)
2
Watchdog Setup : Select to enable this function and select the delay time
(more than 100 seconds is recommended)
Initial Screen Division Setup :Setup the initial Screen Division (screen
layout) after booting.(1,4,9,10,16) How to Setup
1) Select Camera on left <Camera
Tree>.
2) Select Screen Split(Division) on
1)System
drop-down menu (4~16)
Setup
2) Drag & Drop cameras to empty
right Screen Division(Layout)
(Empty Channels have the name
on it)
4. Click Save
How to Modify
Click <All Clear> or click the right
button of Mouse and Select <Clear>
menu to clear each channel
2
Watchdog is the function to reset and reboot the system when detecting
problems like system malfunctions and abnormal recording after Setup Mins.

Schedule Backup Setup: Setup Schedule Backup (Refer to Backup).

ODD Tool: Setup ODD format Tool (DiretCD, InCD), after clicking <Search>
1)Syste
m Setup
TDS Setup (Time, Date, Stamp): To setup Time/Date/Stamp on the Video

Image, which is saved with Video.
Setup Font and Type and Size
Quad D1: 360*240 Resolution

Half D1: 720*240 Resolution
Full ,D1: 720*480 Resolution
Full Screen : Setup initial Screen Division as <Full Screen>

<Ctrl+Alt+Del> Key Lock(Disable): Check in to preventing forced termination and
booting. For System Security. (applied after reboot)
Event Search (Log Viewer) : Check in to use Event Search in Monitoring Screen
(Window)
※User have to check in this to search Events in <Log Viewer>
Beep in Video Loss: Have to Check in to make <Beep> sound in Video Loss
Summer Time Feature: Check in when Summer Time is applied
※ When user applies <summer time feature>, system will backup automatically
the reversed 1 hour data to a selected backup path folder. After backup, the data
in main basket will be deleted, and keep saving continually based on new time.
Users can playback the summer time backup data with <Schedule Backup
Viewer>. For the time shift of less than 5 minutes, the program will protect the old
data and start saving from the new time again to avoid replication.

Backup Directory: Setup the

Folder to save <Backup> data in
applying summer time.
※HDD size is calculated
automatically here.
[How to Use]
1.Check in “Summer Time
Feature”
2.Select Backup folder
3.End DVR program
4. Change the time.
5 Run DVR program
6.Backup is done in backup folder
2)TV out When using this, users can make connected monitors show selected camera
images based on Scenario.
Switch
Mode It can support Max 4 outer monitors when using <TV out Board>.
According to Board, 2 TV out is supported. However using <TV out Board>, 4
monitors can be supported. (Please refer to <TV Out Board> for more detail.

How to Use
1. Check in Use box
2. Monitor : Select outer Monitor
NO to be shown on outer Monitors
3. Camera Number: Select Camera
No to be shown on each outer
monitor. Selected Cameras will be
shown on Monitors by turns based
on Dwelling Time.)
Option
Full Screen: When Checked in ,
monitor shows <Full Screen
Popup> if selected camera is
<Full Screen>
-Event Popup: When checked in ,
monitor shows selected camera if
some events occurs
System Auto-Reboot: To setup <Auto-Reboot the system (PC DVR)> in setup time.
3)Auto
(It is applied to the system in the operation.)
Reboot
System Auto Shut-Down: To setup <Auto shut-down> of system at setup time.
Setting
※Can Setup Time as everyday or a day in a week.
[How to Setup]
-Every Day
-Setup Time/Min
※The Setup Procedure

is the same....for <Auto-
Reboot and Auto Shut-
Down>.

[How to Setup]
-Select a Day or Days in
a week.
-Setup Time/Min
※The Setup Procedure

is the same....for <Auto-
Reboot and Auto Shut-
Down>.

5.2 Resolution Setup
Resolution Setup : Setup resolution fps, compression rate, and Audio (used) for each
channel
1)Camera Click each camera, and setup all values. After setup one camera, and
Selection users want to apply these values to all cameras, just click <Apply All>.
Resolution Setup: Select Resolution for recorded images
NTSC : 720*480, 720*240, 360*240
P A L : 720*588, 720*288, 360*288
FPS Setup: Setup fps
2)Environment (1~30fps(NTSC) 1~25(PAL), if it is over Max fps rate, DVR records the
Setup fps which system can support)
MPEG4 Codec Quality: Can Select Codec Quality
Compression Quality (Low/Medium/High)
(High means High Compression)
Apply All: Apply all setup values to all cameras.

Audio Use: Select Audio(Sound) No to use

(Users can select cam 1 with audio 1 or audio 2…or other)
Live Audio: When checked in, users can hear Live Audio(sound) with
3)Sound Use Video.
Save Audio: When checked in, users can save <Live Audio>
Volume Control : Setup <Audio> Volume(Input Volume)
( Can hear and setup while listening by <Test> tab )
4)Setup Values It shows the Setup Values applied to each channel in the list.
List * To check the details of each bar users can enlarge them.
※For more detail to use <audio>, please refer to “4.5 Chapter How to use Audio”
5.3 Camera Setup
4
5
Camera Setup: Setup Camera Name, Quality, Motion Detection Area, and PTZ
1)Camera Clicking each camera, and setup per camera. To <Apply> the values

Selection to all , click <Apply All> button.

2)Camera Enter Camera Name, which will be shown on Video Image
Name(Description)
Setup the camera image quality (color values) for optimization
(Brightness/Contrast/Saturation/Color)
3)Image Quality User can check the values in Recorded Video and change until
Adjustment getting wanted images.
※If users want to change the values, modify it after clicking
<Default>
Full Area: Setup <All Areas> to detect motion.

4)Detection Area Partial Area: Setup Partial Areas as <Motion Detection Areas>, users
Setup (for Motion) can setup 10 areas as partial <Motion Detection Areas>.
Please note above Pic.
Rate of Detection: Setup the level of detecting unnecessary motion
by noise , Default 10,
Sensitivity: Setup the level of detecting little motion in small point,
defaulted at 10.
※ The motions are checked by both <the rate of detection> and

<the sensitivity> for more accurate motion detection.
[How to test Motion Detection]
1) Select channel to record by motion detection.
2) Check in < Partial Area> for Motion Detection.
Make Partial Areas to add

(Users can make Max 10 areas(Square) just clicking mouse

Drag & Drop by)
3) Setup <Rate of Detection/Sensitivity>.
4) Click <test> button and check the setup values result by
seeing Vidoe.
[Add/Selection/Delete/Delete All]
Add: To Add Partial Area
Select: To Select added Partial Areas or delete them.
Delete: To delete selected Areas
Delete All: To delete all selected areas
5)PTZ
Setup When clicking <Setup> button in PTZ Setup, above setup Window is shown.
Camera Selection : Select PTZ camera

※The Camera No and PTZ Receiver ID have to the same one for normal
working. Each PTZ receiver has individual PTZ ID set switch.
(Simply if PTZ Receiver ID is 1, the camera No has to be No 1)
Receiver Setup: Check in <Use> box, then Setup Menu will be activated.
Select the port, type, communication speed, parity, data bit, and stop bit.
The configurations and available cameras and dome cameras are listed in
the below table.
※ Please refer to the List attached

5.4 Setup Recording Schedule
2 3 4
Schedule Recording: Setup Camera, Recording Type for Schedule Recording

1. Camera User can setup per each camera, when to apply this setup to all, , just
Selection click <Apply All> button.
Use: Check in when using.
Hide Screen: When users want to Hide <Video> of a camera on display
screen, just check in. But Recording is done if it is setup.
2. Camera Setup (It is available in the places users do not want to show the video to
ordinary users like <Safe> or confidential places)
Use Date Display: To write the date on displayed and video recorded
images.
※Event includes all cases like sensor/motion detection in Motion and
Sensor Recording.
3. Event Launch Full Screen : The display Screen turns to <Full Screen> when
Notification detects
an event.
Beep: Generates the beep when detects an event.

(For this users have to check in <Use Video Loss Beep> in <system>
tab, Setup. If not, it does not work)
Border Line: Shows the red outline(Border line) around the image when
detects an event.
Event screen display time(second)??? 영어로 어떻게 되어 있는지
(Event Dwelling Seconds): Setup <Event Dwelling Time> when detects
an event.
Event Selection: Check in Event user wan to get Notification.
※N.B: When <Event Dwelling Seconds> is not check in, user can go
back to the previous screen division by just double-clicking.
※Users can setup Pre(Before)/Post(After) time to record when event
occurs.(Ex, When users setup Pre/Post as 5/5, DVR records starts
recording the video from <before 5 seconds> to < after 5 seconds>
when event occurs)
Pre(Frame) : Can record the Pre Recording Data Max 5 seconds
(Pre Recording saves the 1 frame per second before Event)
Post(Frame) : Can record the Post Recording Data Max 240
seconds
4)Pre/Post
(Pre Recording saves the 1 frame per second before Event)
Recording Setup
The “‘Enable Event” tab automatically activates when the “Normal &
Event”
recording condition is configured.
(The “Normal & Event” recording condition stores specified number of
frames (1~5) per second, automatically changes to record to the
maximum(30FPS) (continuously) when there is an event, and then
constantly saves the specified number of frames again (1~5) if there is
no event after specified period of time.)

[How to Setup]
1. Select the date in the <Select Date>.
5)Holiday Setup 2. Enter the description for the date.

3. Click the <Add> button to register.
1. No Recording: To setup not to record during the day and time period
specified
2. Continuous Record: To setup to record images normally (continuously)
6)Recording
during the day and time zone specified.
Schedule
3. Motion Recording: To setup to any motion detected during the day and
time zone scheduled; Images are not recorded if no motions are detected.
4. Sensor Recording: Record the sensor signals generated during the day
and time
zone specified; Images are not recorded while there are no signal
detection
5. Normal & Event : Continuously records specified number of frames per
second
(1~5 fps to setup), and then records to the maximum(30fps) for specified
period
of time while a specified events (motion, sensor)are detected.
(If Normal & Event recording condition is selected => “Before and
After
Recording Setup” must be selected)
6. Sensor & Motion : To setup to record images when a sensor signal or
motion is detected during the day and time zone specified.

[How to Setup]
1. Select a camera to be setup
2. Select <Recording Type>
3. Setup <Schedule> in <Time Table> by just <Drag & Drop>.
4. To setup several type of Recording, users can add that or change
it after changing <Recording Type>, and just do the same as
above.
※ To apply the same schedule to the entire week and 24 hours,
click the <All> button in the upper left corner of the schedule table
instead of dragging all.
5.5 Network Setup

Setup Network: To setup Network related values, like Port, IP adderss, and
Notification and Dynamic.
1.Network Setup 1. Use Network: Setup to open Network and allow the remote
access through it.
2. IP Setup: Setup TCP/IP .
3. Audio Port Config(X):
Port to transmit <Audio> data.(Default: 6809)
4. Data Port: Setup Data transmission Port.(Default: 6807)
5. Search Port: Setup <Search Port>, which is used in <Remote
Search> through Network. (Default: 6808). To use this, <RSEngin>
has to be in operation in both systems. (Please check Task Bar>.
※ The data transmission, two-way audio, and network notification
functions can be enabled by configuring specific ports.
※ The main reason to use individual port for each function is secure
the system by preventing other ports in Router.

IP Setup Part(1)
In OS MS Window XP
Click <IP Setup> in

<Network Setup>(?)
Select the <Local Area

Network>, and goes to
the <Proprieties> by
clicking right button of
Mouse.
Double-click <TCP/IP>
or click <Registered
Information>

IP Setup Part(2)
Setup IP, Subnet Mask,

Gateway, DNS.
For more information,
users have to ask Network
Expert or Manger
Use: Have to check in here to use <Network Notification> connected

with <RDVR Event Viewer>.
-TEL: Setup Telephone No and Port NO to work in <Dial Up Modem>.
2) Network [How to add IP]
Notification 1) Enter IP address and port ( TCP/IP, xDSL )
2) Make a list of IP using <IP add> and <IP delete>.
※ Maximum 5 can be configured for notification along with the
schedule setup (Including Network II tab.) (Default Port : 8800)
※Please refer to Chapter 7, Web DVR for Dynamic IP Setup.

5.6 Network II Setup
Network Setup 2: Setup Network for Event Transmission and Notification through
Network.
Select a camera to setup (per camera)
1)Select
When want to apply a camera Setup values to all cameras, just click
Camera(X)
<Apply All> button
Use : Check in to use <E-mail Notification>
Condition(?) : Check in the condition of <Email Notification> in the
motion detection (motion), sensor signal detection, or camera
disconnection
[Email Content]
2)E-mail
From : Enter the email address of sender
Notification
To : Enter the email addresses of receivers
C.C : Enter the email addresses of Reference Receiver
Subject : Enter the subject of email
Content: Enter brief message
SMTP : Configure the sending mail server

※ Notify the motion, sensor, and camera disconnection by email.
※If users setup <E-mail Notification> in the camera where occurs a lot
of events, there comes a lot of E-mails. So please setup this with
N.B care in the camera monitoring important place with some events
※ It is recommended to Setup a little longer <Post Recording> in
Event to monitor and record all events.
3) Setup Notification Schedule
Select Channel(Camera)
※Those channels has to be recorded by <Event Recording> by
Step1 Motion or Sensor detection.
※When check in <E-mail Notification>, system sends E-mails by
Schedule.
1. Click <Schedule> button.

2. Configure the schedule by the same method used in configuring
record (drag the mouse or select the <All Apply> button)
Step2
3. Check in Motion or/and Sensor
4. Click <Notify Info> and check the information of each channel.
※Simply <Event Scheduling> is to schedule <Event Notification> by setup time, and

min to RDVR and N-CMS

5.7 Sensor and Relay Setup
Sensor Setup Relay: Setup Senor

Step1 Select Mode <Sensor/Motion/Relay>
Mode Select <Sensor>
Step2 Select camera to setup
Select Mode(X) ※If each camera has different sensor setup, check and setup each
camera camera.
1. Check in Use
2. Enter Sensor ID (Description) which identify it like Hall Door
Step3
3. Select <Sensor Type> (NC / NO3)
Select Sensor
4. Select Camera: Select cameras to record when detecting sensor
Number
( Can choose several cameras)
※The inactive functions change to <Active> when there are available.
3
NC/NO stands for Normal Close/Normal Open, which is 2 type of Sensor. NO type
normally <Open> switch changes to <Close> when signal comes and NC type
normally < Close> switch changes to <Open> when signal comes.
In electronics, a normally open switch is one that normally prevents current flow and
which allows current to flow when it is perturbed.(Cited from Wikipedia)

Motion Setup: Setup Sensor in Motion detection

Step1 Select Mode in <Sensor/Motion/Relay>
Mode Select <Motion>
Select camera to setup
Step2
※If each camera has different sensor setup, check and setup each
Select Camera(X)
camera.
1. Check in Use.
Step3 2. Select Relay: Select <Relay> output when detecting Motion(Can
Relay Setup select several relays)
※The inactive functions change to <Active> when there are available.

Setup Relay: Setup function in Relay

Step1 Select Mode in <Sensor/Motion/Relay>
Select Mode Select <Relay>
Step2 Select camera to setup
Select Camera(X)
1. Check in Use
2. Enter <Description> like Siren
Step3
3. Operation Time (Sec) (1~60)
Relay Setup
※The inactive functions change to <Active> when there are
available.
※Sensor, Motion, and Relay are working closely with each others. So users have to
study the scenario and configure them based on the best combination suitable for
users’ system situation.

5.8 User
User Setup
Single User Setup <registers or edit> Single users who can access and
operate
the System, and the network access rights
Single user is the 1:1 connection to DVR
Group User Setup <registers or edit> Group users who can access and
operate
the System and the network access rights
Group user is the N:N connection to DVRs
※Users can use this function usefully to access many DVRs
simultaneously by <RDVR> and <N-CMS> through Network.
In this case, users have to Setup Group User Account (ID) as
the same one. (예 필요)

User Setup : Setup Single User

Setup <Add, Delete, Edit(?)> for Single User
1. Single User
1. Click <Add> button

2. Enter ID/Password in User Information
3. Check User Rights to manage
(For each user, <admin> can setup different rights)
4. Connectable Camera (?): Setup cameras each user can access and
manage.
5. Click <Confirm> and Exit
※Manage Users by <Add, Delete, Edit(?)> button
※For security and conveniences give normal users less rights and use Group User
to control them at the same time.

Setup Group User : Setup Group User to manage

Setup <Add, Delete, Edit(?)> for Single User.
Using this, users can access and manage DVRs by 1:1, N;1, N:N.
※※Users can use this function usefully to access many DVRs
simultaneously by <RDVR> and <N-CMS> through Network. In this
case, users have to Setup Group User Account (ID) as the same
one.
<N.B> For this, users have to use same registered Group Name
in each Grouped DVRs.
1. Group User
1. Click <Add> button

2. Enter ID/Password in User information
3. User rights are automatically setup (only for Search, Remote
Connection, PTZ control)
4. Click <Confirm> button
※When accessing as <Group User ID>, users can monitor the Video
without changing Setup. This is for enforcing Network Security.
※Manage Users by <Add/Delete/Edit> buttons.
※For more detail information to use Group user, refer to <RDVR>
manual.
※For convenient using, allow normal users less rights, and make them as a <Group
Use>.

5.9 System Information
2 3
System Information: Can check System S/W version, Site Information and System
Information.
Program Version: Can check the DVR S/W version in current system.
1. System
IP address: Can check System Network Adaptor Type and IP address.
Information
2. Site Enter Site Information like (DVR installed Place, Charged Person Name,
Information Tel No, Address.
Check the S/W version in the current system,
※This DVR S/W version help users to upgrade program or problem
shooting.
DVR.exe : DVR Main S/W version
DVRSearch.exe: Search S/W version
3)File Version
DVRFS.exe: ImageDB S/W version
MBackup.exe: Manual Backup S/W version
MBackupView.exe: Manual Backup Viewer S/W version
QuickSearch.exe: Quick Search S.W version
,Option.dll: Version of Files related to Environment Setup

(For our Engineers)
6 How to Search
Click the <Search> button in the monitoring window to display the following
window.
The name and function of each button are described below
검색 종료
Search Window Icons

Shows monthly calendar to search recorded data.
1. Calendar Recorded Data: Yellow, No Recorded Data: White
Current Date: Red
Users can see and search recorded data in this Time Table
2. Search Window (Camera-Hour-Min)
(in Time Table) Color for each Recorded Mode
□□ White: No Data

██ Green: Continuous Recorded Data

██ Yellow: Motion Recorded Data
██ Orange: Sensor Recorded Data
██ Blue: Continuous & Event Recorded Data
██ Pink: Sensor & Motion Recorded Data
※Each Dark Color means <Recorded with Audio>
3. Display Screen It shows the searched Video Image.

It shows the information of recorded data.
4. Information Window
Time/Date/File Size/Recording Mode
Partial enlargement, Play, Search by Frame , Stop Button,
5. Search Button
Audio Search
Screen Division(1,4,9,16)/Zoom(1/1.5/2 Times), Full Screen,
6. Screen Division(Layout)
Book Mark, Partial Enlargement Search
Print, Save, Smart Search, Photo Tool(Image Quality
7. Function Buttons
Control Tool)
6.1 How to Search (Including Audio Search)

1ch Search
Description In 1ch (Full Screen), users can search the data in 1ch.
Click <Search> Icon.
Step1 ※When Clicking, it shows the latest video image. Users can search this right
away.
Click a date to search It shows recorded data for 24 hours
Step2
※How to search: Click << >> button, and choose the date.
Clicking Up/Down button, and select camera
Step3 Using this, it moves to 4 channel in Group.<(1~4) (5~8)>

Step4
When clicking date, users can see and search the recorded data in Time
Table (The above Pic show the data when clicking <yellow> day)
How to move <Hour> to <Min> or <Min> to <Hour>
Step5
When double-click in <Hour> zone, it goes to <Min> zone, and vice-versa.

Click and Play
[How to search Audio]
Step6 1) Click Audio Icon and Search
2) Play with <Audio>.

When clicking
Play/Reverse Play Button
<Speed Up or
Stop Down> Button, the
Speed down, Speed up Button <Search> goes to
Search Frame by Frame 2/4/8/16 times.
6.2 Multi -Search

Multi Search
Description Users can search multi-channel data
Do the same procedure <1ch Search> for <Step 1~5>.
Step1 (To do the same thing to Hour/Min Zone Search)
※When users find wanted data, do the Step 2 for Multi-Search.
Step2 Click wanted <Screen Division> (4/9/ ch)
Step3 Click <Play> button
6.3 Group-Search
Group Search
It is very similar with <Multi-Search>, but the difference is that users can select
설명
and combine wanted channels.
Step 1~5 is the same as 1ch Search.
Step1 (To do the same thing to Hour/Min Zone Search)
※※When users find wanted data, do the Step 2 for Multi-Search.
Step2 Click wanted <Screen Division> (4/9/ ch)
Step3 Step3-1 Step3-2

Click (Up/Down Click the camera Camera 2 changes to Camera 5

button) and goes and <Drag & Drop> Please do the same thing for each
wanted channel to it to right <Screen channel and make wanted <Screen
search Division> Division> with cameras.
Step4 Click <Play> Icon and search
6.4 How to use <Bookmark>

How to use <Bookmark>
It <bookmark> the image (with Description) while searching to search easily when
설명
users want to play after sometime.
Step1
(To do the same thing to Hour/Min Zone Search)
Step2 Play and stop at the image want to <Bookmark>
Click <Add Bookmark>. It is done by clicking right button of
Step3
mouse and select <Add Bookmark>.
Enter simple description to
Identify <Bookmark>, and click
<Confirm> button.
Step4
When clicking <Bookmark>

list, left bookmark list will be
Step5 shown.
[Move wanted Bookmark ]
1. Click in the List.
2. Click <View Image>.

6.5 Partial Enlargement Search

Partial Enlargement
To search wanted images easily by searching in <Enlarged> images.
Descripti
N.B This function is very useful in searching and finding wanted images or
on
movement in big place.
Step1
Click Image Control (quality) Button like the Pic below.
Step2
Click
Step3 <Partial Enlargement>
Icon

Select <Enlarged> area

in the image and
<Draw> the Square like
Step4 left Pic.
That Area will be

<Enlarged> .
Step5
Click <Play> button.

Step6
※To end this, click <Exit> button and goes to <Search Window>.
How to <Zoom Up>
1 1.5 2 Full Screen

Instruction In <1ch> Search, users can Zoom-Up < 1/1.5.2> Times.
N.B Users can use in only <1ch> search with above Icons
TIPs for Search
4
※To search and play D1(Res 720*480/720*576) data, De-interlace filter is applied
automatically. In this D1 Resolution, Zoom Search is not supported.
4
When applying this <De-interlace> filter (S/W), users can get high-quality and
de-interlaced image for search and play.
(Interlace definition in Wikipedia: Interlaced video is composed of 2 fields that are
captured at different moments in time, interlaced video frames will exhibit motion
artifacts when both fields are combined and displayed at the same moment.)

6.6 Panorama Search

Panorama Search
To search images by <16 sequential images>(like the Pic below) by frame,
Descripti which will be very useful to monitor and find <sequential move or small
on movement tracking>.(It looks like Panoramic View, so we call it Panorama
Search)
Step1
Click <Panorama Search)
Step2
Step3 Click <Play> button
Panora
ma
Search

Tips for Search
1. Cameral Move (Up/Down button) 3)Search Pointer

2)Slide Bar
Cameras are Grouped 4 , users move to next Group just clicking
1)Camera Move
Up/Down Button.
It is only shown in the search <Min>, users can search point easily
2)Slide Bar
by drag and move the Bar(Red) like the Pic above.
3)Search Pointer It point out the current <search> Hour/Min.
Hour/Minute Table
In Hour zone, <Red Line> is shown by 3 hours for easy checking, and In Min zone, <Red
Line> is shown by 5 minutes as well.
Information Window
This shows the Y/M/D and H/M/S of recorded Data in
searching, and Camera Name, Recorded Mode as
well.
Continuous Normal & Continuous &
Normal
REC Event Event REC
Normal Motion
Motion
REC Sensor & Sensor &
Sensor Sensor Motion Motion REC
REC
[How to check File Size]

Show Size 1) Just enter <show size> in searched Image and
enter.
2) Can see File Size of searched Image like left Pic
※To hide this, just enter <hide size> and enter.
※In the <default> setup, it is not shown.

6.7 Print
How to Print Image
Description To print the searched image. The image Size depends on Resolution
Step1 Click <Print> Icon.
Step2 Enter the Description for printed image.
Step3
After confirming the image and description, click <Print> button.

Information of Printed Image
1. Signature : Guaranteed DVR Image 6. Computer User Name
2. Name and ID of the camera 7. OS and Serial NO
3. Site installed, owner, site information 8. Video Image
4. Recorded time : Time recorded by the 9. Comment
system
5. Printed time: Time the image is printed.
※To <Print> function, any printer has to be connected with System.

6.8 Save Images as JPEG/AVI file

How to save as JPEG file
Description To save a picture in JPEG format while searching the image
Step1 Click <Save> Icon
Step2
Select Saved Folder. (HDD Drive-Folder )

Step3 File name is made automatically, but can be changed as user wants.
Check in <JPEG> and Click <Ok> button.
Step4
After this message, please <Confirm> button.

6.9 Image Analyzing

Image Analyzing
To analyze saved <JPEG> files and know whether it is forged or alternated

Description
by others.
Run <Start-Program-DVR-ImageAnalyst>
Instruction
Double-click <c:\Program Files\DVR folder\ImageAnalyst>
Step1
Initial
Window
Click <Load> button and

open saved JPEG file.
Step2
Click <Open>

Step3 Check image
Step4
Click <Analyze> button

[Result ] When users see <This is an Original Image> message, it is
original image.

Forgery
Status
[Result ] When users see <This is an Original Image> message, it is not

original image but forged image.
Other
information
When clicking <Information>, users can check Site Name, Camera No/Name,
Save Time, Copy Time, Owner Name, Windows.
When clicking <Original> , it shows the original Image
Click <Exit> button and End

6.10 Save the Image as <AVI> format File
How to save <AVI> file

Using this, users can save <Video> as <AVI> file, which can be played
Description simply in other PC by Window Media Player?
※Please learn more on Backup-AVI Backup.
6.11 Motion Search

How to search Motion
To search specific <Motion> in recorded Video in wanted area, which is very
Description
useful to monitor and track down an object in any place.
Step1
Click the <Motion Search> Icon
Make an <square> in an area users wan to search <Motion>

1. Click <Motion Search> button
2. Make an <square> in an area users wan to search <Motion> just by
Step2 dragging mouse. (Specify a section in the Video Image>
3. Setup the rate of Sensitivity and Motion.
※ For more details of <the rate of Sensitivity and Motion>, refer to <Motion
Recording>
Set search time in <Start> and <End> Time
Step3
※<Start> time can be searched time when searching.
Check in <Auto Search> or <Manual Search>
※ The difference between <Auto Search> and <Manual Search> is the
Step4
automatic listing of searched data. So users expect big list, please use
<Auto Search>.
Step5 Click <Search> button
Step6 When finished, <message> will be shown.

Step7
When Clicking one in a list, searched image will be shown like the Pic above.
※Bookmark the searched image

1. Select a image.
2. Click <Add> to Bookmark list
3. Click <Apply> button and save it in the Bookmark.
4. In <Bookmark> list and play the video in <Search Window>.
※ When clicking the event list, <video playback> message will be shown and
can play.
Step 1~3 is the same as <Auto Search>
Check in <Manual Search> and click <Search> button.
Enter bookmark description
manually, <Add Bookmark> window
will be shown when finished
<search>. If it is useful, enter
Manual
bookmark description or end it.
Search
Click <Apply> button.
※Searched images can be checked in Bookmark List.

6.12 Image Quality Control

How to setup <Image Quality Control Tool>
Description Setup and control Video Image Quality for favored color.
Brightness compensation
Contrast correction
Color Value Compensation
Sharpness/Undo
Blur
White/Black Change: Undo
Exit
※To change the values of <Image Quality>, have to open <Image Quality Control
Tool>. For other menu, have to <Exit> this.
TIPs : Easy Bookmark
Bookmark
While searching Video, users can add <Bookmark> by just clicking

of right button of mouse and select <Add Bookmark> menu like the
Pic above.( For more, please refer to <Bookmark>
De-Interlace Filter
In S/W version 5.0, we applied automatic <De-Interlace filer> in
D1(720*480/720*576) resolution. With this, users can play and
search Highest Quality Video.
To apply <De-Interlace filer> in the old version, users have to use

quick button of mouse in <searched Video> like left Pic.
Exit
Exit and return to Main Window.

7 Web-DVR
Web DVR is the Software which makes DVR backup and remote-monitored in Web
Browser like IE (Internet Explore) not in Taylor made Remote Client S/W (like RDVR)
just when it is connected through Network in any where and anyplace.
By using this, user can control P/T/Z, live monitoring, and save image data and
print.
[ Web-DVR Configuraiton ]
How to connect and use Web DVR

Authentication Server Application : To manage Users and DVR
DB
Web Sever(IIS): To supply Web Interface (User registration
Authentic
Network and management)
ation
Environment ※Have to use <Fixed IP> with OS more than <Window 2000
Server
Server>
※ Authentication Server makes users use and access to DVR
by IE regardless of fixed or Dynamic IP .
Transmit information to DVR:IP address and Port No…
DVR ※DVR login as registered Web Account, and transmit

information and update.

Access through Internet by IE (Internet Explorer) in PC
User
Web DVR account Registration , ID/Password Management
Prepared 1. Have to register Web Account in www.servntec.com

things 2. Have to setup Network in DVR
7.1 To register <Web Account> in <Authentication Server

[Instruction 1] To register <Web Account> in <Authentication Server
Step1 Open Web Site www.servntec.com
Step2
Click Dynamic IP Service

Click “DVR member registration” in the bottom
Step3

Step4
Enter each <“ * “ area a <must>). (Member ID, Password, Name, Email,
Mobile Phone No) and Click <Member Registration>.

Step5
Click “OK”
※ Pictures above shows the registration procedure as <ID: Webdvr , Password: webdvr>,
when this is done normally, users can get <Information Email> for normal registration.
When users can not get this registration email, please keep below address in mind and
check and register again.
-Dynamic IP Server : dims.servntec.com
※In case users want to run <Authentication Server>(Web Server)

Some sites or users want to run theirs own <Authentication Server>(Web Server) not
Servntec Server (or in some places, it is hard to access to Servntec Web Server), in this
users have to run independent Web Server. For this users can install <Authentication
Server>(Web Server), however for more details , please discuss with Sales and Tech
Support Team.
※ Needed things to setup independent Server

<Authentication Server>(Web Server): Setup Server o PC, License, Environment to make
Authentication(API is needed)
ActiveX License: Licensed ActiveX is in the environment OS in Window XP SP2 and latest
OS. (Users have to get licensed Key from MS, please refer to Microsoft Site)
Web Design and Packaging: Have to prepare Web Design and elements for Authentication
for users, when they are accessing by IE not RDVR.
-Web Server (IIS or others): Have to Web Server like IIS or Apache to register and manage
users through IE.
※Servntec offers these kind of Web Server Environment, which has had good reputation
form users. For more instruction and details, please refer to Manual (including RDVR)
and our Tech and Sales Team.

7.2 Network Setup in DVR (Server not RDVR)

This shows the instruction how to setup Network for Web Account and Authentication
Sever Registration.
[Instruction 2 ] Network Setup in monitored DVR

Step1 Login as Admin in DVR.
Click <User Management> tab
and register.
Enter <User ID, Password and

Authority and Name and
Step2 Connectable Cameras> and
click <OK> button.
Goes to <Network> tab.
Step3
Check in <Use> box, and enter the same < User ID(DVR ID), Password, Web
DVR Description and Web DVR User ID and Server IP> and click <Register>
button)
Click and confirm left Pic message.
Step4 ※If users have another message, please

enter again. And ID is already registered
one, please overwrite.

7.3 How to Use Web DVR

With Web DVR , users can access , monitor live image , search and playback, and
control remote PTZ by Internet Explorer (IE) on remote PC.
PC system requirement
Check Microsoft Internet Explorer version 6.0 or more.
Points Open Pop-Up in OS window XP SP2 and more in IE.
How to open Pop-Up
Step1 Click Tool-Internet Option in IE.
Step2 Goes to <user information> tab.
In Pop-Up Block, check
out in <Popup Block>
Box
Click OK
Step3
※When users want to
open Pop-up for
selected sites, please
follow below
instruction.
Step4 Click <Setup> button on Step3
Please enter sites

(Dims.servntec.com)
to open Pop-Up and
click <add> button.
Step5 (Dims.servntec.com)
Confirm <Alarm and

Filter Level> and click
<Close> button.
※The easiest way to open <Pop-Up> is click <OK> button with < Ctrl > key after
entering Web Account and Password. However it is not recommended to prevent
other web sites access.

7.3.1 To Monitor Live Video (images)

Monitor Live Video (images)
Step1 www.servntec.com …Go
Step2 Click Dynamic IP Service
Enter
-ID/Password
Step3
-webdvr/webdvr
And click OK button
Step4
Pop-up
Window
When users can not see Pop-up window above, please check and do the
same procedure <Open Pop-up> above.
※If users save DVR account (ID/Password) by just clicking <diskette> icon,
users can check registered camera information, please use this.

N.B
When users can see resisted DVRs in the list, however in the View status
some DVR are <Off>, which means DVRs are off or are not linked with
Serer. In this case, please check this with charged person.
Step5 Select <Full 선택하고, and click <Go> in Veiw.
Step6
When above window is shown, click and install <AciveX Control>
Step7
Click <Install>

When finished, Live View (Monitoring View) will be shown. (like the Pic
Step8
below)
Web-DVR Live View (Live Monitoring View)
3
2
4
1.Screen Camera: Select camera in No Split(Full Screen) screen
Division Control Screen Split (Screen Division): No Split, 4 Split(Quad)(1-4, 5-8,9-12,13-
16), 9Split(1-9, 10-16), 16 Split(1-16) (Split means Screen Division)
Zoom In : Available in No Split (Zoom In 1, 2)
Save and Print Icon: To save AVI file and print the image in <No Split>
screen.(BMP save and Print)
2.PTZ Control To control PTZ in remote DVR
3. Live Display Live Video Area
Area
4. Exit Exit/PlayBack(Remote Search)
N.B When users want to save <Live Video> as <AVI> file, click right button of
Save <AVI> file Mouse, and select <AVI Save> button on wanted camera, display area.
If use this, this <AVI> files will be saved in C/Driver folder. To stop this,
please click again right button of Mouse and select <AVI Stop>. (This
function is added in Version 2.0)

7.3.2 How to <Playback> (Remote Search)

Playback(Remote Search)
Step1 Step1~4 in 8.3.1 Live View is the same.
Select <Full> and Click <Go> in <Playback>.
Step2
※ It is the same in clicking <Playback> in Live View Window in 8.3.1.
Step3
When above window is shown, click and install <AciveX Control>
Step4
Click <Install>.

Step8 When finished, <Playback> window like the Pic below will be shown.
Web-DVR Playback Window
3 4
1. Search 1. Y/M/D Selection: Select Y/M/D in the <Search Calendar>, when there
Calendar are <Recorded Data>, those date will be show in <White>.
2. Select Hour, Minute, and Camera, and Searched Video will be shown.
2. Screen Multi Search (1, 4,9,16 screen division can be searched at one time
Divion <Multi-Search>)
Save, Print Icon: Save and Print Icon: To save AVI file and print the
image in <No Split> screen.(BMP save and Print)
3. Searched Searched Video will be displayed according to select screen division
Video Display
Area
4.Play and Exit <Search Speed Side Bar, Play/Reverse Play, Previous/Next Frame,
Stop, Exit > Button

The left Pic show the searched image

in the procedure like 8.3.1 Select
<Full> and Click <Go> in
<Playback>.

8 Appendix
8.1 How to reinstall DVR S/W.

Reinstallation
Double-click the Setup.exe in S/W installation CD, and Install.
Click <Next> Click <Next>
Select S/W installed folder and Click Installation is going on

<Next>
Click <Finish>
※To delete installed S/W, users can delete all in <Control Panel>--Program Add or
Delete..

8.2 Open (Remove/Unlock) Firewall in Window XP

To Unlock Blocking in Window XP
In XP, users have to unlock firewall in the port for Normal use.
Description ※Normally in the first installation of system, the <Firewall Open>

message will be show. But when users did not unlock this, users can
remove <Firewall> by <Program add or delete.
1) Run <Windows Security Center> in <Control Panel>-<Window
Security Center> and click <Exceptions>.
2) Check in the list like the Pic above for <Exceptions> List.
To unlock
(like the Pic below)
<Blocking>
※Programs to be checked and those functions.
1. AgentClient.exe : Event Transmission with RDVR
2. DVR.exe : Main DVR S/W
3. RDVR2WayServer.exe: To support 2-way Audio with RDVR
4. RSEngine.exe: To support remote-search with RDVR, N-CMS
Exceptions
Window
※How to add Programs

1. Click <Program Add>.
To add
2. Search and click exe files to add.
Programs
3. Click <open>
4. Click <OK> and add

8.3 Window Display Setup

Users have to set suitable resolution & color accordingly to the recommendation.
Display Setup
Please setup like below in <Registration Information> or <Properties> in Desktop
Setup up Resolution and Colors
Resolution: 1024*768 over

Color: True Color in 32Bit
Never use Screen Saver.

Make sure to be [None]
Please make the Power

Schemes to be <Always
On >
Have to make the

<System standby>, <Turn
off monitor>, <Turn off
hard disc> to be <Never>

8.4 How to use CD format tools in Backup

How to use CD format tools
To use this for format backup media (CD-R, CD-R/W, DVD), and save the
backup data in them.
※To format media, users have to <designate> format tool folder in <Select
Tool>(Refer to Backup Procedure)
Designate <Format Tool>
1. Click <Select Tool>
Description 2. Goes to the folder where has installed <Format Tools> and click
them (like InCD, Direct CD) and click Open(For this, Tools have to
be installed first)
To Format
1. When inserting not used media, <Auto-Format> is in run by <Plug &
Play>
2. Format them by <Format Tools>(S/W)
In case using Nero INCD
Instruction Nero INCD has to be installed first before use.
Check in <Format> box

and click <Start>.
Step1
※Enter Name in <Label>

Step2 Click <OK> after finish.
In case using Easy Creator Direct CD

Instruction Direct CD has to be installed first before use.
Insert blank media

and run Direct CD
Step1
Click <Format CD>
Enter the Name

Step2 in<Label> and click
<Start Format>.
Step3 <Format >is running

Step4
When finished successfully, above window will be shown

※포맷한 미디어는 백업 및 저장위치 지정 시에 포맷한 Media 가 들어있는 드라이브를
선택하여 백업 및 파일 생성 및 복사를 진행하여 줍니다.
줍니다 (??? 이해가 안되요)
안되요
[Direct CD Delete Option]

There are 3 options after getting out media after format. Users have to select <UDF
Reader installation>.When users want to monitor the data in other PCs, users have
to install this <UDF Reader> first and check the data.
8.5 Available protocols according to Company and Brand.
Baud Data Stop

index Receiver parity Preset
rate Bit Bit
0 Dvna 9600 N 8 1 X
1 DY 9600 N 8 1 X
2 Fine 2400 N 8 1 X
3 Kalatel(N/A) 9600 N 8 1 X
4 Linlin 9600 N 8 1 X
5 Panasonic(wv-cs850) 19200 N 8 1 X
6 Pelco D 2400 N 8 1 O
7 Philips(tc8560,tc700) 9600 N 8 1 X
8 Serim 9600 N 8 1 X
9 Sungjin 4800 M 8 1 X

10 Vicon 4800 N 8 1 X
11 Dyuni 9600 E 8 1 X
12 MP200 9600 N 8 1 X
13 KD6 9600 N 8 1 X
14 Samsung(scc-641) 9600 N 8 1 X
15 Oriental 2400 O 8 1 X
16 Techwin 9600 N 8 1 X
17 OMNIVIEW 9600 N 8 1 X
18 CNB 9600 N 8 1 X
19 CTNCOM 9600 N 8 1 X
20 NIKO(NK-97CHE) 9600 N 8 1 X
21 SENSORMETIC 9600 N 8 1 O

Baud Data Stop Preset

Index Receiver parity
rate bit bit
22 NEOSSRX-1 4800 E 8 1 X
23 PT101 9600 N 8 1 X
24 PANASONIC V12 19200 N 8 1 O
25 VICONEXT N 8 1 X
26 SECURTEX_B 4800 N 8 1 X
27 SMAILCAM 19200 N 8 1 X
28 DRX502A,DSC-230S 9600 N 8 1 X
29 HSDN-251 9600 N 8 1 O
30 SAMSUNG SRX100A 9600 E 8 1 X
31 CNB-SMART 9600 N 8 1 X
32 HL(HRX-1000) 9600 N 8 1 X
33 DVRX_1000 9600 N 8 1 X
34 FastraxII_HID2404 9600 N 8 1 O
35 SAE 9600 N 8 1 O
36 KTD_313 9600 N 8 1 O
37 VSD_640 9600 N 8 1 O
38 AD1650/2050 9600 N 8 1 X
39 KTS-2000 UltraDome 9600 N 8 1 O
40 DYSPD-255 9600 N 8 1 O
41 KRE-301/302 9600 N 8 1 X
42 Pelco-D ( Cynix ) 9600 N 8 1 O
Note: The above information is subject to change due to

the change of product names by manufacturers or other reasons.

8.6 FAQ
<Q01> When DVR power do now work.
1. Check the connection of Power Cable.
Power
2. Check the Voltage (115V/230V).(Switcher)
3. When using <Multi-Tab>, check the power and connection.
<Q02> When display is not coming.
1. Check the connection between DVR and Monitor.
Display
2. Check the Monitors Power.
3. Check the Brightness of Monitor.
<Q03> When Camera Images are not coming.
1. Check the connection of cable of Cameras and DVR board.
2. Check the Power of Camera.
3. Check the <Use> in Camera Setup in DVR.
4. Check the Camera status whether it is normal or not.
Video(Image)
<Q04> When Camera image comes in B/W or abnormal(warped)
status..
1. Check the cameras status first, and change them.
2. Check the right Status of Video Type <NTSC /PAL>, and camera
type too.
<Q05>When PTZ is not working normally.
1. Check the right connection of RS-422/485 converter and
PTZ PAN/TILT
(Please refer to PTZ H/W connection in Installation Manual)
2. Change the connection of RX-422/485 converter.
<Q06> When <Motion Recording> is not working normally.
1. Check the right setup of <Motion Area> in Camera tab, Setup.
2. Check the right setup of <Schedule> of Motion Recording in
<Schedule of Recording>.
3. Check the <Holiday> setup for that date.
Recording <Q07> When <Sensor Recording> is not working normally.
1. Check the connection of Sensor and Camera in <Sensor> and
<Relay>.
2. Check the right Sensor type and normal connection.
3. Check the right setup of <Schedule> of Sensor Recording in
<Schedule of Recording>.

4. Check the <Holiday> setup for that date

<Q08>When users can not monitor <Backup> data.
Check the Date Form (Y/M/D) of DVR and another PC (to monitor
Backup
the Backup Data)
(The Date Form(Y/M/D) has to be the same as DVR)
<Q09> When <Print> does not work normally.

1. Check the connection of Printer and DVR and Power On/Off
Print
2. Check the right Driver installation in PC DVR for printer.
4. Check the Default Printer Setup when several printers are used
<Q10> When RDVR are not connected.
1. Check the Network Cable connection.
2. Check the right <IP setup> in <Network> Setup.
3. Check the <Use> of Network i in <Network> Setup.
Network
<Q11> When 2Way-Audio does not work normally.
1. Check the right work of <Agent client>
2. Check the Unlock of <Blocking>(of Firewall) in window XP sp2.
3. Check the connection and setup of Microphone,
<Q12> How to connect rightly PTZ H/W components.
PTZ H/W
connection
1. For the connection of <Ext>, connect PTZ connection 1, and 2.
2. In PTZ connection 2, check the right connection of Signal(Tx+)
GND(tx-) in Receiver Terminal.
3. Check the right Setup in <PTZ setup> in Camera.
4. Check the right PTZ Protocol setup for Receiver.
5.For another PTZ protocol and cameras can be supported when
Users need.

8.7 H/W connection with External Devices
Case(Front)
Case(Back)
※This can be changed according to Model, please note this.

Connection Configuraiton
Sensor, Relay, PTZ Connection Configuration

Warranty
Product
SERIAL NO.
Purchase Data D/M/Y
Warranty Period For 1 Year from purchasing
Where
⊙ This warranty is not offered again.

⊙ When purchasing, users have to pay attention to the details of Warranty
and A/S
⊙ In A/S for maintenance or repair, users have to offer this Warranty Sheet.
⊙ Please read with care the available <Free A/S cases> in the Manual.
※ Please contact Servntec Tech Support Team or Sales Team for

Services
Memo:


nEYE PC DVR User Guide PDF

Uploaded by

Copyright:

Available Formats

nEYE PC DVR User Guide PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

nEYE PC DVR User Guide PDF

Uploaded by

Copyright:

Available Formats

DVR User Guide v1.

Model [SDC SERIES, SDR SERIES]

Service of New Technology

2.1 SYSTEM COMPONENTS .......................................................................................................5

3 SYSTEM OVERVIEW ...........................................................................................................6

3.1 SYSTEM FEATURES .............................................................................................................8

4 MAIN WINDOW ..................................................................................................................12

4.1 INSTRUCTION ON MAIN WINDOW ....................................................................................12

5 ENVIRONMENT SETUP ....................................................................................................39

5.1 SYSTEM SETUP .................................................................................................................40

6 HOW TO SEARCH ..............................................................................................................65

6.1 HOW TO SEARCH (INCLUDING AUDIO SEARCH) ...............................................................66

7.1 TO REGISTER <WEB ACCOUNT> IN <AUTHENTICATION SERVER ......................................83

8.1 HOW TO REINSTALL DVR S/W. ........................................................................................94

And let’s start DVR …with this Manual.

Intellectual rights and properties , and Trade Mark

User Guide v1.0 Page 1

Check Points for installation

2) Please avoid the place where has strong electromagnetic waves

4) Pease avoid place where is directly open to low temperature of

6) Please avoid the place where has high vibration or temperature or

7) Please check the power voltage before connecting power.

User Guide v1.0 Page 2

N.B Points to use

2) Please study the manual first before operating DVR.

3) Recommend contacting supplier or Servntec’s support team before

4) Please do not handle consent or power lines with wet hands.

5) Please connect power lines to consent correctly.

6) Please do not use thinner, Benzene, or alcoholic matter as cleaner.

7) Please keep away from the extended terminal.

8) Please shut all program and S/W before Power Off.

10) Please do not dismantle or maintain the system without discussion

11) Please do not put heavy things on the system.

12) Please do not move the system while system is running.

User Guide v1.0 Page 3

The available warranty for free change is 1 year.

[ The Cases when warranty is not applied ]

1. System Shut Down by users’ mistake.

2. Careless using which is not based on Manual Instruction.

3. Irregular Power Using which is not based on Manual

4. Warranty is not applied to the consumption components change and

5. Malfunctions caused by system maintenance or dismantling while

6. Though the warranty is over, upgrade and maintenance service

User Guide v1.0 Page 4

DVR system case (1SET) Power cable / System Open KEY

OS License Label (Windows XP or 2000 )

DVR Kit Configuration ( DVR board and Option)

User Guide v1.0 Page 5

This is commonly known as the DVR(Digital Video Recorder)

DVR in <Wikipedia… www.wikipedia.org >. Please read more on this.

[Pic DVR vs RDVR Configuraiton]

User Guide v1.0 Page 6

[CCTV System Configuration using 3 DVRs ]

User Guide v1.0 Page 7

3.1 System Features

DVR System Main Features

-More than 20000 copies are distributed, tested , and

- In D1(720*480/720*576) Resolution, De-interlace filer

User Guide v1.0 Page 8

- In D1(720480/720576) Resolution, De-interlace filer