Yamaha RX-E810, RX-E410, NX-E800 Micro Combo

MICRO COMPONENT SYSTEM MCR-E810/MCR-E410
RX-E810/RX-E410/ NX-E800 SERVICE MANUAL

SERVICE MANUAL
The MCR-E810 is composed of the RX-E810, NX-E800 and DVD-E810.
The MCR-E410 is composed of the RX-E410, NX-E800 and CDX-E410.
This service manual is for the RX-E810, RX-E410 and NX-E800.
For service manual of the DVD-E810 and CDX-E410, please refer to the following publication number:
DVD-E810 101017
CDX-E410 101018
IMPORTANT NOTICE
This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.
It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are
already known and understood by the users, and have therefore not been restated.
WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in per-
sonal injury, destruction of expensive components, and failure of the product to perform as specified. For
these reasons, we advise all YAMAHA product owners that any service required should be performed by
an authorized YAMAHA Retailer or the appointed service representative.
IMPORTANT: The presentation or sale of this manual to any individual or firm does not constitute authorization, certifica-
tion or recognition of any applicable technical capabilities, or establish a principle-agent relationship of
any form.
The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering,
and service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore,
inevitable and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to
exist, please contact the distributor's Service Division.
WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have
accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this
buss).
IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to
the unit.
■ CONTENTS
TO SERVICE PERSONNEL . . . . . . . . . . . . . . . . . . . . 2 DISPLAY DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
SYSTEM COMPOSITION . . . . . . . . . . . . . . . . . . . . . . 3 IC DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18–22
FRONT PANELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 BLOCK DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . 23–24
REAR PANELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–6 PRINTED CIRCUIT BOARDS . . . . . . . . . . . . . . . 25–31
REMOTE CONTROL PANELS . . . . . . . . . . . . . . . . . . 6 PIN CONNECTION DIAGRAMS . . . . . . . . . . . . . . . . 32
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 SCHEMATIC DIAGRAMS . . . . . . . . . . . . . . . . . . 33–37
INTERNAL VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 REPLACEMENT PARTS LIST . . . . . . . . . . . . . . 39–48
DISASSEMBLY PROCEDURES . . . . . . . . . . . . . . . . . 8 REMOTE CONTROLS . . . . . . . . . . . . . . . . . . . . . 49–50
RX-E810/RX-E410/
SELF DIAGNOSIS FUNCTION (DIAG) . . . . . . . . . 9–15 SYSTEM CONTROL . . . . . . . . . . . . . . . . . . . . . . 51–58

NX-E800
AMP ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . 16
101019 2006 All rights reserved.

This manual is copyrighted by YAMAHA and may not be copied or
redistributed either in print or electronically without permission.
P.O.Box 1, Hamamatsu, Japan
'06.07
RX-E810/RX-E410/NX-E800
■ TO SERVICE PERSONNEL AC LEAKAGE

WALL EQUIPMENT TESTER OR
1. Critical Components Information OUTLET UNDER TEST EQUIVALENT
Components having special characteristics are marked s
and must be replaced with parts having specifications equal
to those originally installed.
2. Leakage Current Measurement (For 120V Models Only)
When service has been completed, it is imperative to verify
that all exposed conductive surfaces are properly insulated
INSULATING
from supply circuits.
TABLE
● Meter impedance should be equivalent to 1500 ohms shunted ● Leakage current must not exceed 0.5mA.
by 0.15µF. ● Be sure to test for leakage with the AC plug in both polarities.
“CAUTION”
“F1, F2: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 3.5A,
125V FUSE.”
CAUTION
F1, F2: REPLACE WITH SAME TYPE 3.5A, 125V FUSE.
ATTENTION
F1, F2: UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE DE 3.5A, 125V.
WARNING: CHEMICAL CONTENT NOTICE!

The solder used in the manufacturing process except soldering of the P.C.B. ass'y contains LEAD. In addition, other
electrical/electronic and /or plastic (where applicable) components may also contain traces of chemicals found by the
California Health and Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive
harm.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REA-
SON WHATSOEVER!
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose
eyes to solder/flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands before
handling food.
About Lead Free Solder

The P.C.B.s installed in main unit are soldered using the all lead free solder.
Among some types of lead free solder currently available, it is recommended to use one of the following types for the repair
work.
• Sn + Ag + Cu (tin + silver + copper)
• Sn + Cu (tin + copper)
• Sn + Zn + Bi (tin + zinc + bismuth)
Caution:
As the melting point temperature of the lead free solder is about 30°C to 40°C (50°F to 70°F) higher than that of the lead
solder, be sure to use a soldering iron suitable to each solder.
RX-E810/RX-E410/
NX-E800
2
RX-E810/RX-E410/NX-E800
■ SYSTEM COMPOSITION
The MCR-E810 consists of the DVD-E810, RX-E810 and NX-E800.
The MCR-E410 consists of the CDX-E410, RX-E410 and NX-E800.
MCR-E810 (U, C, T, K, A, B, G, L, V models) MCR-E410 (B, G models)
DVD-E810 CDX-E410
RX-E810 RX-E410
NX-E800 NX-E800
RX-E810/RX-E410/
NX-E800
x2 x2
3
RX-E810/RX-E410/NX-E800
■ FRONT PANELS ■ REAR PANELS

RX-E810 (U, C, T, K, A, B, G, L, V models) RX-E810 (U, C models)
RX-E410 (B, G models) RX-E810 (T model)
NX-E800 (U, C, T, K, A, B, G, L, V models) RX-E810 (K model)
RX-E810 (A model)
RX-E810/RX-E410/
NX-E800
4
RX-E810/RX-E410/NX-E800
RX-E810 (B model) RX-E410 (B model)
RX-E810 (G model) RX-E410 (G model)
RX-E810 (L model)
RX-E810 (V model)
RX-E810/RX-E410/
NX-E800
5
RX-E810/RX-E410/NX-E800
NX-E800
■ REMOTE CONTROL PANELS

RX-E810 RX-E810 RX-E410
(U, C, T, K, A, L, V models) (B, G models) (B, G models)
RX-E810/RX-E410/
NX-E800
6
RX-E810/RX-E410/NX-E800
■ SPECIFICATIONS
■ AUDIO SECTION • DIMENSIONS
Minimum RMS Output Power (Power Amp. section)
(7/8")
Channel Separation Finish
21.8
20 Hz to 20 kHz, 0.1 % THD, 6 ohms .............. 40 W + 40 W [RX-E810] [RX-E810]
1 kHz, 0.1 % THD, 6 ohms ............................... 55 W + 55 W DVD, etc., Input 5.1 k-ohms shorted, 1 kHz / 10 kHz Gold color ............................................................ T, A models
Dynamic Power Per Channel (IHF) ........................................................... 60 dB / 45 dB or more Black color ................................................................. G model
6 ohms ............................................................... 60 W + 60 W [RX-E410] Silver color ................................... U, C, K, B, G, L, V models
4 ohms ............................................................... 75 W + 75 W CD, etc., Input 5.1 k-ohms shorted, 1 kHz / 10 kHz [RX-E410]
2 ohms ............................................................ 100 W + 100W ........................................................... 60 dB / 45 dB or more Black color ................................................................. G model
Max Power Per Channel (B, G models) Tone Control Characteristics Silver color ........................................................... B, G models
1 kHz, 0.7 % THD, 4 ohms ............................... 60 W + 60 W BASS : Boost/Cut ..................................... ±10 dB (50 Hz) Accessories
IEC Power (B, G models) Turnover Frequency .................................. 350 Hz Remote control x 1, Battery x 2, Indoor FM antenna x 1, AM
1 kHz, 0.04 % THD, 6 ohms ............................. 55 W + 55 W TREBLE : Boost/Cut ................................... ±10 dB (20 kHz) loop antenna x 1, System control cable x 1
Maximum Useful Output Power (JEITA) (L, V models) Turnover Frequency .................................. 3.5 kHz
325.1 (12-13/16")
362.5 (14-1/4")
1 kHz, 10 % THD, 6 ohms (L, V models) ...................... 65 W Gain tracking error (0 to -60 dB) ........................... 2 dB or less ■ SPEAKER SECTION (NX-E800)
Power Band Width (0.1 % THD, 30 W, 6 ohms) Type ................................................................. 2-way bass reflex
FRONT L/R ................................................... 10 Hz to 50 kHz ■ FM SECTION Magnetic shielding type
Damping Factor Tuning Range Driver
20 Hz to 20 kHz, 6 ohms ...................................... 60 or more U, C, L, V models ...................................... 87.5 to 107.9 MHz Tweeter ......................................... 2.5 cm (1") soft dome type
Input Sensitivity/Input Impedance T, K, A, B, G, L, V models .................... 87.50 to 108.00 MHz Woofer ............................................. 13 cm (5-1/8") cone type
[RX-E810] 50 dB Quieting Sensitivity (IHF) (1 kHz, 100 % MOD.) Frequency Response ........................ 55 Hz to 28 kHz (-10 dB)
DVD, etc. ................................................ 150 mV / 47 k-ohms Mono ............................................................ 2.8 µV (20.2 dBf) to 80 kHz (-30 dB)
[RX-E410] Signal to Noise Ratio (IHF) Impedance ....................................................................... 6 ohms
CD, etc. ................................................... 150 mV / 47 k-ohms Mono / Stereo ................................................... 73 dB / 70 dB Rated Input ......................................................................... 60 W
Maximum Input Voltage (1 kHz, 0.5 % THD) Harmonic Distortion Maximum Input ................................................................ 110 W
(5/8")
15.6
[RX-E810] Mono / Stereo (1 kHz) ........................................ 0.5 % / 0.5% Sensitivity ........................................................ 87 dB / 2.83 V/m
DVD, etc. .......................................................... 3.0 V or more Antenna Input ............................................ 75 ohms unbalanced Crossover Frequency ........................................................ 3 kHz
[RX-E410]
Input Terminal .............................................. Screw/Banana type
100 (3-15/16")
CD, etc. ............................................................. 3.0 V or more
108.2 (4-1/4")
■ AM SECTION Dimensions (W x H x D) .......................... 186 x 300 x 223 mm
Rated Output Voltage/Output Impedance
Tuning Range (7-5/16" x 11-13/16" x 8-3/4")
SUBWOOFER ............................................. 2.0 V / 680 ohms
U, C, L, V models ......................................... 530 to 1710 kHz Weight ........................................................... 4.3 kg (9 lbs. 7 oz)
REC OUT .................................. 150 mV / 1.2 k-ohms or less
T, K, A, B, G, L, V models ........................... 531 to 1611 kHz
Headphone Jack Rated Output/Impedance Finish
Antenna .................................................................. Loop antenna Light cherry/Silver color ........................ U, C, A, B, G models
[RX-E810]
(5/16")
Black/High gloss piano color 215 (8-7/16")
DVD, etc. (1 kHz, 150 mV, 8 ohms) ......... 0.23 V / 120 ohms
8.2
[RX-E410]
■ GENERAL ......................................... U, C, T, K, A, B, G, L, V models
CD, etc. (1 kHz, 150 mV, 8 ohms) ........... 0.23 V / 120 ohms Power Supply Accessories .................................................. Speaker cable x 2
U, C models ................................................. AC 120 V, 60 Hz Unit: mm (inch)
Frequency Response (20 Hz to 20 kHz)
T model ........................................................ AC 220 V, 50 Hz
[RX-E810]
K model ....................................................... AC 220 V, 60 Hz * Specifications are subject to change without notice due to product
DVD, etc. ................................................................ 0 ± 0.5 dB
A model ....................................................... AC 240 V, 50 Hz improvements.
[RX-E410]
B, G models ................................................. AC 230 V, 50 Hz
CD, etc. ................................................................... 0 ± 0.5 dB U .......... USA model C ...... Canadian model
L model ............................................ AC 220-240 V, 50/60 Hz
Total Harmonic Distortion (20 Hz to 20 kHz, 30 W/6 ohms) T .......... Chinese model K ...... Korean model
V model ........................................... AC 110-120 V, 50/60 Hz
[RX-E810] A .......... Australian model B ...... British model
Power Consumption G .......... European model L ....... Singapore model
DVD, etc. to SP OUT ...................................... 0.04 % or less
U, C, V models ............................................................. 115 W V .......... Taiwan model
[RX-E410]
T, K, A, B, G, L models ................................................ 130 W
CD, etc. to SP OUT ......................................... 0.04 % or less
Standby Power Consumption (Reference data)
Signal to Noise Ratio (IHF-A Network)
....................................................................................... 0.1 W
[RX-E810]
DVD, etc., Input shorted (150 mV) ................. 93 dB or more Maximum Power Consumption (V model)
“iPod” is a trademark of Apple Computer, Inc., registered in the
(250 mV) .................. 98 dB or more 1 kHz, 6 ohms, 10 % THD ........................................... 300 W
U.S. and other countries.
[RX-E410] AC Outlets
CD, etc., Input shorted (150 mV) .................... 93 dB or more Switched x 2
(250 mV) .................... 98 dB or more U, C, T, G, L, V models .............................. 100 W max. total
Residual Noise (IHF-A Network) Switched x 1
Pure direct on .............................................................. 100 µV A, B models ................................................. 100 W max. total
Dimensions (W x H x D) .................... 215 x 108.2 x 362.5 mm
(8-7/16" x 4-1/4" x 14-1/4")
Weight ......................................................... 5.7 kg (12 lbs. 9 oz)
7
RX-E810/RX-E410/NX-E800
• When checking the P.C.B.:

■ INTERNAL VIEW a. Remove the top cover and the front panel unit. k. With the rear panel attached, set the MAIN P.C.B. on its
b. Remove 2 screws (6). (Fig. 3) side.
1 2 3 4 5 6 c. Remove the OPERATION (2) P.C.B. which is con- At this time, set the power transformer on its side as
nected directly to the lower P.C.B. with connections. well. (Fig. 5)
1 MAIN (3) P.C.B. (U, C, T, A, B, G, L, V models) d. Remove 6 screws (7). (Fig. 4) l. Using a ground lead or the like, connect G2 and G4 of
2 Power Transformer e. Remove 5 screws (8). (Fig. 4) the MAIN P.C.B. with the rear panel. (Fig. 5)
3 MAIN (2) P.C.B. f. Remove 2 screws (9). (Fig. 3) m. With the front panel unit set on its side, reconnect 5 con-
4 AM / FM Tuner g. Remove 1 screw (0). (Fig. 1) nectors (CB18, CB21, CB200, CB201, CB209). ( Fig. 6)
5 OPERATION (2) P.C.B. h. Reinstall the OPERATION (2) P.C.B.. n. Connect the power cable, turn on the power and check
6 INPUT (1) P.C.B. i. Reinstall 2 screws (6). (Fig. 3) for operation.
7 OPERATION (1) P.C.B. j. Remove the power transformer and MAIN P.C.B. (with
8 INPUT (2) P.C.B. the rear panel attached) from the main chassis. (Fig. 5)
9 MAIN (1) P.C.B.
0 MAIN (4) P.C.B.
Power transformer Ground lead
G4
OPERATION (2) P.C.B.
G2
6
7 8 9 0
Heat sink
Rear panel Ground lead MAIN (1) P.C.B.

9
■ DISASSEMBLY PROCEDURES
Fig. 3 Fig. 5
(Remove parts in disassembly order as numbered.)
1. Removal of Top Cover 2. Removal of Front Panel
a. Remove 4 screws (1) and 4 screws (2). (Fig. 1) a. Remove CB18, CB21, CB200, CB201 and CB209. (Fig. 2)
b. Lift the top cover at the rear and move it rearward slantingly. b. Remove 2 screws (3), 2 screws (4) and 1 screw (5). CB209 CB200 CB18 CB21
(Fig. 1) (Fig. 1)
c. Release 2 hooks and remove the front panel unit by pull- 7
ing it forward. (Fig. 1)
8
CB21 Front panel unit
Top cover 2 MAIN (4) P.C.B.
CB201
7
1
CB18
Front panel unit 1 CB200
CB201 Front panel unit

Hook
Main chassis
CB209
3 Fig. 4 Fig. 6
0
5
4 3 INPUT (1) P.C.B.
Hook MAIN (1) P.C.B. INPUT (2) P.C.B.
Fig. 1 Fig. 2
8
RX-E810/RX-E410/NX-E800
■ SELF DIAGNOSIS FUNCTION (DIAG)

This unit has self diagnosis functions that are intended for inspection, measurement and location of faulty point.
There are 9 DIAG menu items, each of which has sub-menu items.
Listed in the table below are menu items and sub-menu items.
No. MAIN MENU SUB MENU

1 FIRMWARE VERSION 1. FIRMWARE VERSION / MODEL / DESTINATION
2. CHECK SUM ALL
2 VFD CHECK 1. Initial display
2. VFD DISPLAY OFF
3. VFD DISPLAY ALL
4. VFD DIMMER
5. CHECK PATTERN
3 FACTORY PRESET 1. PRESET INHI (memory initialization inhibited)
2. PRESET RSRV (memory initialized)
4 AD DATA CHECK 1. PRT1/PRT2
2. PRT3/THM
3. SYSTEM STATUS
4. DESTINATION
5. PANEL KEY (Key0/Key1)
5 iPod (DOCK) 1. DOCK : OK/NG
2. IP_PWR / IP_DET
6 PROTECTION HISTORY 1. HISTORY 1
2. HISTORY 2
3. HISTORY 3
4. HISTORY 4
7 ERROR INFORMATION 1. INDICATION
2. RESET
8 MUTE CHECK 1. SP/HP OFF
2. SP MUTE
3. HP MUTE
9 POWER OFF FACTOR 1. HISTORY 1
HISTORY 2. HISTORY 2
3. HISTORY 3
4. HISTORY 4
5. HISTORY 5
RX-E810/RX-E410/
NX-E800
9
RX-E810/RX-E410/NX-E800
• Starting DIAG
Press the “STANDBY/ON” key while simultaneously pressing those two keys of the main unit as indicated in the figure
below.
Keys of main unit
Turn on the power while pressing these keys.
• Starting DIAG in the protection cancel mode

If the protection function works and causes hindrance to trouble diagnosis, cancel the protection function as described
below, and it will be possible to enter the DIAG mode. (The protection functions other than the excess current detect function
will be disabled.)
Press the “STANDBY/ON” key while simultaneously pressing those two keys indicated in the figure above. At this time, keep
pressing those two keys for 3 seconds or longer.
In this mode, the “SLEEP” segment of the FL display of the main unit flashes to indicate that the mode is DIAG mode with the
protection functions disabled.
CAUTION!
Using this product with the protection function disabled may cause damage to itself. Use special care for this point when
using this mode.
• Canceling DIAG
1 Before canceling DIAG, execute setting for FACTORY PRESET of DIAG menu No.3 (Memory initialization inhibited or
Memory initialized).
* In order to keep the user memory stored, be sure to select PRESET INHIBITED (Memory initialization inhibited).
2 Turn off the power by pressing the “STANDBY/ON” key of the main unit.
• Display provided when DIAG started

On the FL display of the main unit, an opening message (including the version and the protection history) appears for a few
seconds followed by the diagnostic menu display (1. FIRMWARE VERSION).
When there is no history of protection function:
Opening message DIAG menu display

RX-E810/RX-E410/
When there is no protection history After a few seconds

NX-E800
NO PROTECT B VER.B16 4BG
Version (1 alphabet)
10
RX-E810/RX-E410/NX-E800
When there is a history of protection function:

The FL display appears as shown below depending on the type of the protection function.
The protection function worked due to a defect or overload in the power supply. If the power
P1 PRT:000 A
is turned on with the abnormality unsolved, the protection function works in about 3 sec-
onds to turn off the power.
P3 PRT:000 A
The protection function worked due to the temperature limit being exceeded. Causes could
TM PRT:000 A
be poor ventilation or a defect related to the thermal sensor. If the power is turned on with
the abnormality unsolved, the protection function works in about 3 seconds to turn off the
power.
For detection of each protection function, refer to DIAG MENU No.4 AD DATA.
History of protection function

When the protection function has worked, its history is stored in memory with a backup. Even if no abnormality is noted while
servicing the unit, an abnormality which has occurred previously can be defined as long as the backup data has been
stored.
The history of the protection function is cleared when DIAG is cancelled by selecting PRESET RESERVED (Memory
initialized) of DIAG menu No.3 or when the backup data is erased.
• Operation procedure of DIAG menu and SUB-MENU

There are 9 MENU items, each of which has some SUB-MENU items.
DIAG menu selection

Main unit: Select the menu using the “B”(Forward) and “N”(Reverse) keys of PRESET/TUNING.
SUB-MENU selection
Main unit: Select the sub-menu using “PRESET/BAND” (Forward) Key and “AUTO/MAN’L” (Reverse) key.
Keys of main unit

DIAG menu selection SUB-MENU selection
Reverse Forward Reverse Forward
• Functions in DIAG mode

In addition to the DIAG menu items, functions as listed below are available.
• Input selection
• Muting
• Power on/off
RX-E810/RX-E410/
* Functions related to the tuner and the set menu are not available.
NX-E800
• Initial settings used to start DIAG

The following settings are used when starting DIAG.
When DIAG is canceled, these settings are restored to those before starting DIAG.
• Input DVD (RX-E810 model), CD (RX-E410 model)
11
RX-E810/RX-E410/NX-E800
1. FIRMWARE VERSION
The firmware version, model, destination and checksum are displayed.
The checksum is obtained by adding the data at every 16 bits for each program area and expressing the result as a 4-figure
hexadecimal data.
* Numeric values in the figure example are for reference.
Firmware version of microprocessor

VER.xxx 8 UC
Description (UC, BG, ATK, LV)
Model (8: RX-E810, 4: RX-E410)
Checksum value of microprocessor

SUM:xxxx
2. DISPLAY CHECK
This program is used to check the FL display section.
The display condition varies as shown below according to the sub-menu operation.
Checking FL display section
Initial display
Initial display
All segments OFF
All segments OFF
All segments ON (dimmer 100%)
Lighting of segments in lattice
Lighting of segments in lattice

RX-E810/RX-E410/
Lighting in lattice
NX-E800
Short Normal
Segment conditions of the FL driver and the FL tube are checked by turning ON and OFF all segments. Next, the operation
of the FL driver is checked by using the dimmer control. Then a short between segments next to each other is checked by
turning ON and OFF all segments alternately (in lattice). (In the above example, the segments in the second row from the top
are shorted.)
12
RX-E810/RX-E410/NX-E800
3. FACTORY PRESET
This menu is used to reserve/inhibit initialization of the backup RAM (Set menu contents, etc. of the sound field program).
PRESET INHIBIT (Initialization inhibited)

3.PRESET INHI
RAM initialization is not executed. Select this sub-menu to protect the values set by the user.
Note: The protection history will not be erased using PRESET INHIBIT.
PRESET RESERVED (Initialization reserved)

3.PRESET RSRV
Initialization of the back-up RAM is reserved. (Actually, initialization is executed the next time that
the power is turned on.) Select this sub-menu to reset to the original factory settings or to reset
the RAM. Use PRESET RESERVED to erase the protection history.
CAUTION: Before setting to the PRESET RESERVED, write down the existing preset memory.
Content of the Tuner in a table as shown below. (This is because setting to the PRESET RESERVED will cause
ALL user memory contents to be erased.)
Preset group P1 P2 P3 P4 P5 P6 P7 P8
4. AD DATA CHECK
This menu is used to display the A/D conversion value of the Microprocessor which detects panel keys of the main unit and
protection functions in using the sub-menu.
When K0/K1 menu is selected, keys become non-operable due to detection of the values of all keys. However, it is possible
to advance to the next sub-menu by turning the INPUT of the main unit.
* Numeric values in the figure example are for reference.
P1/P2 (Power supply voltage protection detection)

Power supply voltage protection value (Normal value: P1: 102 to 400, P2: 102 to 329)
P1: Detects +5I, ±B and AC2.
P2: Detects +5I, ±12, +10V, -VP and AC1. P1:xxx P2:xxx
* If Px is out of the normal value range, the protection function works to turn off the power.
(Reference voltage: 5V=500)
P3/TH (Power supply voltage protection detection/Temperature detection)

P3: Amp DC protection (Normal value: 0 to 402)
* If Px is out of the normal value range, the protection function works to turn off the power.
TH: Detects the temperature of the heat sink. P3:xxx TH:xxx
Temperature detected value
RX-E810/RX-E410/
(Normal value: 0 to 176) U, C, T, K, A, B, G models

NX-E800
(Normal value: 0 to 170) L, V models

13
RX-E810/RX-E410/NX-E800
SYSTEM STATUS 5. iPod

The voltage value of pin No. 92 of IC200 is displayed, us- DOCK loop back check
ing 5V/500 as standard. After turning off the power, short between pins No. 14 (TX)
and No. 18 (RX).
SI:xxx [y]:OK (Make sure that the power is turned off when shorting
pins.)
OK: Normal
NG: Out of specified range
Note) Be sure to return the shorted locations to their
0: 0 (PORaT_STANDBY) original state.
1: H 1/3 (PORT_PRE_STANDBY)
2: H 2/3 (PORT_STOP)
3: H (PORT_PLAY)
Display Description
15 16 17 18
0 - 41 [ 0 ] OK
43 - 123 0-1 NG
9 10 11 12 13 14
125 - 207 [ 1 ] OK
209 - 290 1-2 NG
3 4 5 6 7 8
292 - 374 [ 2 ] OK
376 - 456 2-3 NG
1 19 20 21 2
458 - 500 [ 3 ] OK
DOCK
OK: Normal
NG: Error
DESTINATION
The destination of this unit is displayed. 5.DOCK:OK
DEST:000
Check item Judgment Display

Destination for AD port (Pin No. 97 of IC200) Pull-up resis-
Is UART loop pack check result OK? YES OK 
tance 10k-ohms. 
NO NG 
Ohm 0 2.7k 15.0k 47.0k
V 0-0.2 0.7-1.3 2.8-3.3 3.9-4.3
Pin 94
B, G U, C L, V T, K, A
(DEST)
DOCK status
The status of pins No.1 (PWR) and No.4 (iPDET) of the
DOCK connector is displayed.
PANEL KEY (K0/K1) PWR (iPod accessory power)

When the A/D value of the panel key becomes out of the HI: Detected
specified range, normal operation will not be available. LO: Undetected
Check each panel key for the constant of the partial pres-
sure resistance, soldered condition, etc, referring to the DET (iPod installation to DOCK)
table below. HI: Installed
(Reference voltage: 5 V=100 %) LO: Not installed
RX-E810/RX-E410/
K0:494 K1:496 PWR:LO DET:HI

NX-E800
Display K0 K1
0 - 41 DISPLAY PRESET / TUNING B
43 - 109 MEMORY / TIME ADJ. PRESET / TUNING N
111 - 317 PRESET / BAND –
14
RX-E810/RX-E410/NX-E800
6. PROTECTION HISTORY 9. TURN OFF THE POWER FACTOR HISTORY

Four protection histories are displayed. Up to 5 past factors which caused the power to turn OFF
are displayed.
When the “MEMORY” key is pressed during display, the
6-1 No PRT history of the power OFF causal factors are initialized.
6-4 No PRT 9-1 NO HISTORY
9-5 NO HISTORY
7. PROTECTION HISTORY RESET

The PROTECTION history is initialized. Select [HIST RE- Display Factor
SET] and press the “MEMORY” key, and the PROTEC-
Microprocessor reset
TION history will be initialized. 9-x CPU RESET
Power down
HIST DISP 9-x POWER DOWN
Protection
9-x PROTECTION
HIST RESET
Sleep/Timer off
9-x TIMER OFF
HISTORY DISPLAY
The RAM is not initialized. The past PROTECTION history Panel key
is not erased. 9-x PANEL KEY
“STANDBY/ON”
HISTORY RESET Remote control key

9-x REMOCONKEY
The past PROTECTION history is erased. Have HIST RE- “STANDBY/ON”
SET displayed and press the ‘MEMORY’ key, and the past
Auto standby
PROTECTION history will be erased. 9-xAUTOSTANDBY
Not history
9-x NO HISTORY
8. MUTE
Using the sub-MENU, select the MUTE status of SP
(Speaker out)/HP (Phones).
The MUTE function of SP

MUTE OFF
(Speaker out) and HP
(Phones) is turned OFF.
The MUTE function of SP

SP MUTE ON
(Speaker out) is turned ON.
RX-E810/RX-E410/
NX-E800
The MUTE function of HP

HP MUTE ON
(Phones) is turned ON.
15
RX-E810/RX-E410/NX-E800
■ AMP ADJUSTMENTS
● Confirmation of Idling Current
1) No signal applied.
2) Non-loaded condition.
3) Aging is not necessary.
Item Test Point Rating (DC) Note
MAIN L R94 If the measured voltage exceeds 2.6mV, cut the lead wire of R80 (L ch)
(Between terminal) or R81 (R ch) and then check again if each measured value satisfies the
0.05mV–2.5mV rating.
R95
MAIN R (Between terminal)
* Confirm that the idling current is 0.25mV – 15mV after 60 minutes.
0.05mV ~ 2.5mV (DC)
R80 (L ch)
R81 (R ch)
Q17 MAIN (1) P.C.B.
Cut OFF
R94 (L ch)
R95 (R ch)
R94
R80
Note)
R95 • If the idling current exceeds 2.6mV after a power
amplifier repair, check for a defective component
R81 before cutting the resistor.
• If R80 (L ch) or R81 (R ch) have already been cut off
and idling current does not flow, reconnect R80 (1k-
ohms) or R81 (1k-ohms).
• Q17 and Q18 are transistors for temperature correc-
Q18 tion. Apply silicone grease to the contact surface with
the heat sink.
RX-E810/RX-E410/
NX-E800
16
RX-E810/RX-E410/NX-E800
■ DISPLAY DATA
● V501 : 16-BT-133GNK (VH034300)
u 1
PATTERN AREA
● PIN CONNECTION
Pin No. 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
Connection P17 P18 P19 P20 P21 P22 P23 P24 P25 P26 P27 P28 P29 P30 P31 P32 P33 P34 P35 NC 16G 15G 14G 13G 12G 11G 10G 9G 8G 7G 6G 5G 4G 3G 2G 1G NP NP NX F1
Pin No. 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41
Connection F2 NX NP NP P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16
Note : 1) F1, F2 ..... Filament 2) NP ..... No pin 3) NX ..... No extened Pin 4) 1G ~ 16G ..... Grid 5) NC ..... No connection
● GRID ASSIGNMENT
16G
1G 2G 3G 4G 5G 6G 7G 8G 9G 10G 11G 12G 13G 14G 15G
1-1 2-1 3-1 4-1 5-1
1-2 2-2 3-2 4-2 5-2
1-3 2-3 3-3 4-3 5-3
1-4 2-4 3-4 4-4 5-4
1-5 2-5 3-5 4-5 5-5
1-6 2-6 3-6 4-6 5-6
1-7 2-7 3-7 4-7 5-7

(1G~15G)
● ANODE CONNECTION
1G∼15G 16G 1G∼15G 16G 1G∼15G 16G

P1 1-1 P13 3-3 P25 5-5
P2 2-1 P14 4-3 P26 1-6
P3 3-1 P15 5-3 P27 2-6 –
P4 4-1 P16 1-4 P28 3-6 –
P5 5-1 P17 2-4 P29 4-6 –
RX-E810/RX-E410/
P6 1-2 P18 3-4 P30 5-6 –

NX-E800
P7 2-2 P19 4-4 P31 1-7 –

P8 3-2 P20 5-4 P32 2-7 –
P9 4-2 P21 1-5 P33 3-7 –
P10 5-2 P22 2-5 P34 4-7 –
P11 1-3 P23 3-5 P35 5-7 –
P12 2-3 P24 4-5
17
RX-E810/RX-E410/NX-E800
■ IC DATA
IC200 : M30620MCP-A41FP (INPUT P.C.B.)
Microprocessor
P2_7/AN2_7/A7(/D7/D6)
P2_5/AN2_5/A5(/D5/D4)
P2_6/AN2_6/A6(/D6/D5)
P2_1/AN2_1/A1(/D1/D0)
P2_4/AN2_4/A4(/D4/D3)
P2_2/AN2_2/A2(/D2/D1)
P2_3/AN2_3/A3(/D3/D2)
P2_0/AN2_0/A0(/D0/-)
P1_7/D15/INT5
P1_6/D14/INT4
P1_5/D13/INT3
P3_0/A8(/-/D7)
P1_2/D10
P3_6/A14
P1_3/D11
P3_7/A15
P1_4/D12
P4_0/A16
P4_1/A17
P3_2/A10
P4_2/A18
P3_3/A11
P4_3/A19
P3_4/A12
P3_5/A13
P1_0/D8
P1_1/D9
P3_1/A9
VCC2
VSS
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
P0_7/AN0_7/D7 81 50 P4_4/CS0
P0_6/AN0_6/D6 82 49 P4_5/CS1
P0_5/AN0_5/D5 83 48 P4_6/CS2
P0_4/AN0_4/D4 84 47 P4_7/CS3
P0_3/AN0_3/D3 85 46 P5_0/WRL/WR
P0_2/AN0_2/D2 86 45 P5_1/WRH/BHE
P0_1/AN0_1/D1 87 44 P5_2/RD
P0_0/AN0_0/D0 88 43 P5_3/BCLK
P10_7/AN7/KI3 89 42 P5_4/HLDA
P10_6/AN6/KI2 90 41 P5_5/HOLD
P10_5/AN5/KI1 91 40 P5_6/ALE
P10_4/AN4/KI0 92 39 P5_7/RDY/CLKOUT
P10_3/AN3 93 38 P6_0/CTS0/RTS0
P10_2/AN2 94 37 P6_1/CLK0
P10_1/AN1 95 36 P6_2/RXD0/SCL0
AVSS 96 35 P6_3/TXD0/SDA0
P10_0/AN0 97 34 P6_4/CTS1/RTS1/CTS0/CLKS1
VREF 98 33 P6_5/CLK1
AVCC 99 32 P6_6/RXD1/SCL1
P9_7/ADTRG/SIN4 100 31 P6_7/TXD1/SDA1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
P8_3/INT1
P9_6/ANEX1/SOUT4
VSS
BYTE
XOUT
P9_0/TB0IN/CLK3
XIN
P8_2/INT0
CNVSS
P9_4/DA1/TB4IN
P9_1/TB1IN/SIN3
P8_7/XCIN
P9_2/TB2IN/SOUT3
P9_5/ANEX0/CLK4
VCC1
P8_6/XCOUT
P8_4/INT2/ZP
P7_1/RXD2/SCL2/TA0IN/TB5IN (1)
P7_0/TXD2/SDA2/TA0OUT (1)
P9_3/DA0/TB3IN
RESET
P8_1/TA4IN/U
P7_4/TA2OUT/W
P7_2/CLK2/TA1OUT/V
P7_6/TA3OUT
P8_0/TA4OUT/U
P8_5/NMI
P7_7/TA3IN
P7_5/TA2IN/W
P7_3/CTS2/RTS2/TA1IN/V
8 8 8 8 8 8 8
Port P0 Port P1 Port P2 Port P3 Port P4 Port P5 Port P6

<VCC2 ports>(4)
Port P7
<VCC1 ports>
Internal peripheral functions

8
A/D converter System clock

(10 bits X 8 channels generation circuit
Timer (16-bit) Expandable up to 26 channels)
Port P8
XIN-XOUT
Output (timer A): 5 UART or XCIN-XCOUT
7
Input (timer B): 6 clock synchronous serial I/O PLL frequency synthesizer
(8 bits X 3 channels) On-chip oscillator
<VCC1 ports>
Three-phase motor
Port P8_5
control circuit CRC arithmetic circuit (CCITT ) Clock synchronous serial I/O
(Polynomial : X 16+X12+X5+1) (8 bits X 2 channels)
M16C/60 series16-bit CPU core Memory

RX-E810/RX-E410/
Port P9
R0H R0L SB ROM

Watchdog timer R1H R1L 128K
USP
(15 bits) R2
8
ISP RAM
R3
NX-E800
DMAC INTB 10K

(2 channels) A0
PC
Port P10
A1
FB FLG
D/A converter
8
(8 bits X 2 channels) Multiplier
18
RX-E810/RX-E410/NX-E800

Microprocessor
Pin No. Port Name I/O Function

1 P96/ANEX1/SOUT4 SADEV_DI O Serial data output
2 P95/ANEX0/CLK4 SADEV_DO SI Serial data input
3 P94/DA1/TB4in SADEV_CK O Serial clock output
4 P93/DA0/TB3in TU_STAT I TUNED detect
5 P92/TB2in/SOUT3 TU_ST/MON I STEREO detect
6 P91/TB1in/SIN3 TU_MUTE O TUNER MUTE output
7 P90/TB0in/CLK3 O
8 BYTE BYTE MCU Vss: When using single chip mode
9 CNVss CNVss MCU Vss: When using singe chip mode
10 P87/Xcin Xcin MCU Sub-clock oscillation input
11 P86/Xcout Xcout MCU Sub-clock oscillation output
12 /RESET /RESET MCU Reset
13 Xout Xout MCU Oscillation output
14 Vss Vss MCU Ground for microprocessor
15 Xin Xin MCU Oscillation input
16 Vcc1 Vcc MCU Power for microprocessor +5V
17 P85/NMI NMI MCU
18 P84/INT2 O
19 P83/INT1 /TIMER IRQ TIMER SW
20 P82/INT0 O
21 P81/TA4in/U RDS_DO I RDS data to microprocessor (B,G models)
22 P80/TA4out/U RDS_DI O RDS data to IC (B,G models)
23 P77/TA3in RDS_CK O RDS serial clock out (B,G models)
24 P76/TA3out RDS_CE O RDS CE out (B,G models)
25 P75/TA2in/W O
26 P74/TA2out/W /CEEEP O
27 P73/CTS2/RTS2/TA1in/V O
28 P72/CLK2/TA1out/V O
29 P71/RXD2/SCL2/TA0in/TB5in O
30 P70/TXD2/SDA2/TA0out O
31 P67/TXD1/SDA1 TXDF SO
32 P66/RXD1/SCL1 RXDF SI
33 P65/CLK1 CLKF SO
34 P64/CTS1/RTS1/CTS0/CLKS1 BSY O
35 P63/TXD0/SDA0 IP_TXD SO iPod TxD
36 P62/RXD0/SCL0 IP_RXD SI iPod RxD
37 P61/CLK0 IP_DET I iPod detect
38 P60/CTS0/RTS0 IP_PWR I iPod accessory power detect
39 P57/RDY/CLKout CLKOUT I Sub-clock output
40 P56/ALE TU_PSW O Tuner power control
O H = Power on / L = Power off
41 P55/HOLD /EMP I
42 P54/HLDA O
43 P53/BCLK O
44 P52/RD O
45 P51/WRH/BHE O
46 P50/WRL/WR /CE I
47 P47/CS3 O
48 P46/CS2 O
49 P45/CS1 O
50 P44/CS0 O
51 P43/A19 MODEL I E810/E410 model identify (L = RX-E810)
RX-E810/RX-E410/
52 P42/A18 I
53 P41/A17 I
NX-E800
54 P40/A16 I
55 P37/A15 O
56 P36/A14 O
57 P35/A13 O
58 P34/A12 I
59 P33/A11 O
60 P32/A10 O
61 P31/A9 O
62 Vcc2 Vcc MCU Power for microprocessor +5V
19
RX-E810/RX-E410/NX-E800

Microprocessor
Pin No. Port Name I/O Function

63 P30/A8 O
64 Vss Vss MCU Ground for microprocessor
65 P27/A7 O
66 P26/A6 O
67 P25/A5 O
68 P24/A4 PD_LED O PURE DIRECT LED output
69 P23/A3 P_RLY O Power relay output
70 P22/A2 SYS_I I Protection inhibit/Permit identify input
I L = Permitted / H = Inhibited
71 P21/A1 SYS_O O System communication output
72 P20/A0 SP_RLY O Speaker relay output
73 P17/D15/INT5 P_DET IRQ Power down detect
IRQ Interrupt
74 P16/D14/INT4 /STANDBY IRQ STANDBY/ON SW input
IRQ Interrupt
75 P15/D13/INT3 REMOTE IRQ Remote control input
IRQ Interrupt
76 P14/D12 /HP_DET I Headphone detect
I H = Headphone mounted
77 P13/D11 TIMER_LED O TIMER LED output
78 P12/D10 /FL_IC O FL driver reset output
79 P11/D9 /FL_CE O FL driver CE
80 P10/D8 FL_DT O FL driver data output
81 P07/D7 FL_CK O FL driver clock output
82 P06/D6 ROT_B I INPUT selector rotary B
83 P05/D5 ROT_A I INPUT selector rotary A
84 P04/D4 PDIRECT I PURE DIRECT SW input
I L = SW on / H = SW off
85 P03/D3 MVOL_UP O Motor volume up output
86 P02/D2 MVOL_DW O Motor volume down output
87 P01/D1 HP_MUTE O Headphone mute output
I L = Mute on
88 P00/D0 SP_MUTE O Speaker mute output
I L = Mute on
89 P107/AN7/KI3 KEY1 AD AD key1 input
90 P106/AN6/KI2 KEY0 AD AD key0 input
91 P105/AN5/KI1 PROT_TH AD AD protection temperature detect
92 P104/AN4/KI0 SYS_AD AD AD system status detect
93 P103/AN3 PROTECT1 AD AD protection detect 1
96 Avss Avss MCU Ground for AD
97 P100/AN0 DEST AD AD destination identification
98 Vref Vref MCU AD reference
99 Avcc Avcc MCU AD power
100 P97/Adtrg/Sin4 SADEV_CE O CE output
Ket input (A-D) Pull-up resistance 33 k-ohms

ohm 0 +6.8 k +5.6 k
V 0 - 0.427 - 1.110 - 3.183
pin 90
DISPLAY MEMORY/TIME ADJ PRESET/BAND
RX-E810/RX-E410/
(KEY0)
pin 89
PRESET/TUNING B PRESET/TUNING N –
NX-E800
(KEY1)
Destination for AD port

Pull-up resistance 10 k-ohms
ohm 0 2.7 k 15.0 k 47.0 k
V 0 - 0.2 0.7 - 1.3 2.8 - 3.3 3.9 - 4.3
pin94
B, G models U, C models L, V models T, K, A models
(DEST)
20
RX-E810/RX-E410/NX-E800
IC501 : M66003-0131FP (OPERATION P.C.B.)

FL display driver
DIG14/SEG39
DIG12/SEG41
DIG13/SEG40
DIG11/SEG42
DIG07
DIG06
DIG08
DIG05
DIG09
DIG00
DIG04
DIG10
DIG01
DIG02
DIG03
VP
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
RESET 1 48 DIG15/SEG38
CS 2 47 DIG16/SEG37
SCK 3 46 DIG17/SEG36
SDATA 4 45 SEG35
Vss 5 44 SEG00
XOUT 6 43 SEG01
XIN 7 42 SEG02
Vcc1 8 41 SEG03
SEG34 9 40 SEG04
SEG33 10 39 SEG05
SEG32 11 38 SEG06
SEG31 12 37 SEG07
SEG30 13 36 SEG08
SEG29 14 35 SEG09
SEG28 15 34 SEG10
SEG27 16 33 SEG11
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
SEG26
Vcc2
SEG25
SEG24
SEG23
SEG22
SEG21
SEG20
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
Display code
RAM CGROM
(35 bit x 166) 44 SEG00
(8-bit x 60)
Code Segment 19 SEG25
write output 17 SEG26
circuit
dot data
CGROM 9 SEG34
CS 2 Serial data (35 bit x 16)
write
SCK 3 receive
circuit Code/
SDATA 4 command
control 45 SEG35
circuit DIG11/
52
SEG42
51 DIG12/
SEG41
code Segment DIG13/
select 50
digit SEG40
select/ 49 DIG14/
XIN 7 Clock output SEG39
timing Display
generator clock controller scan pulse circuit 48 DIG15/
XOUT 6
SEG38
47 DIG16/
SEG37
46 DIG17/
RX-E810/RX-E410/
SEG36
NX-E800
63 DIG00
Digit
RESET 1 output
Vcc1 8 circuit
53 DIG10
Vcc2 18
Vss 5
Vp 64
21
RX-E810/RX-E410/NX-E800
IC501 : M66003-0131FP (OPERATION P.C.B.)

FL display driver
Pin No. Symbol Name Function

1 RESET RESET Reset input When “L”, M66003 is initialized.
2 CS CEFD Chip select input When “L”, communication with the MCU is possible.
3 SCK CKFD Shift clock input When “H”, any instruction from the MCU is neglected.
4 SDATA DTFD Serial data input Serial input data is taken and shifted by the positive edge of SCK.
5 Vss Vss GND (0V)
6 XOUT XOUT Clock out When use as a CR oscillator, connect external resistor and capacitor.
7 XIN XIN Clock in When use an external clock input external clock to XIN, and XOUT must be opened.
8 Vcc1 Vcc1 Positive power supply for internal logic.
9 SEG34 P1
10 SEG33 P2
11 SEG32 P3 Connect to segment (anode) pins of VFD. Pins from SEG00 to SEG42 corre-
12 SEG31 P4 spond to segment pins of VFD as shown in the table below. SEG36–SEG42 pins
Segment output are common to DIG11–DIG17 pins. So when use SEG36–SEG42, the number of
13 SEG30 P5
14 SEG29 P6 digit to be used is decreased.
15 SEG28 P7
16 SEG27 P8
17 SEG26 P9
18 Vcc2 Vcc2 Positive power supply for DIG and SEG outputs.
19 SEG25 P10
20 SEG24 P11
21 SEG23 P12
22 SEG22 P13
23 SEG21 P14
24 SEG20 P15
25 SEG19 P16
26 SEG18 P17
27 SEG17 P18
28 SEG16 P19
29 SEG15 P20
30 SEG14 P21
Connect to segment (anode) pins of VFD. Pins from SEG00 to SEG42 corre-
31 SEG13 P22
spond to segment pins of VFD as shown in the table below. SEG36–SEG42 pins
32 SEG12 P23 Segment output
are common to DIG11–DIG17 pins. So when use SEG36–SEG42, the number of
33 SEG11 P24
digit to be used is decreased.
34 SEG10 P25
35 SEG09 P26
36 SEG08 P27
37 SEG07 P28
38 SEG06 P29
39 SEG05 P30
40 SEG04 P31
41 SEG03 P32
42 SEG02 P33
43 SEG01 P34
44 SEG00 P35
45 SEG35 N.C.
46 DIG17/SEG36 N.C.
47 DIG16/SEG37 N.C. Connect to segment (anode) pins of VFD. Pins from SEG00 to SEG42 corre-
48 DIG15/SEG38 G16I spond to segment pins of VFD as shown in the table below. SEG36–SEG42 pins
Digital output /
49 DIG14/SEG39 G15 are common to DIG11–DIG17 pins. So when use SEG36–SEG42, the number of
Segment output
50 DIG13/SEG40 G14 digit to be used is decreased. / Connect to digit (grid) pins of VFD.
51 DIG12/SEG41 G13
52 DIG11/SEG42 G12
RX-E810/RX-E410/
53 DIG10 G11
54 DIG09 G10
NX-E800
55 DIG08 G9
56 DIG07 G8
57 DIG06 G7
58 DIG05 G6 Digital output Connect to digit (grid) pins of VFD.
59 DIG04 G5
60 DIG03 G4
61 DIG02 G3
62 DIG01 G2
63 DIG00 G1
64 VP VP Negative power supply to pull down.
22
A B C D E F G H I J
RX-E810/RX-E410/NX-E800
1
■ BLOCK DIAGRAMS
AUDIO SECTION BLOCK DIAGRAM
To DVD/CD
OPERATION (1)
SYS_AD
• See page 33 →
/RESET
SYS_O
SCHEMATIC DIAGRAM INPUT (1)
2 • See page 37 →
XL200 SCHEMATIC DIAGRAM
32.7kHz
Timer LED
D501 12 10 11 92 71
77
35 IP_TXD
75 36 IP_RXD
IR Remote
U501
37 IP_DET DOCK for iPod
82, 83 Power Supply Detection

Input Selector 38 IP_PWR
93pin P1 AC2, ±B, +5I
SW501
94pin P2 AC1, ±12, +5I, -VP, +10V
3 91, 93- 95
Microprocessor
FL Display
Standby/ON Key 74 Power AMP Error Detection

IC200
V501
SW502 97 95pin P3 Over Current, DC Out Detection

M30620 Destination Detect
51 Model Detect
Tact Switch
89, 90 Temperature of Main Radiator Detection
SW503, 504, 505, 506, 507, 508 69 91pin TH
Power Relay
72
Speaker Relay
FL Driver 78- 81
IC501
87 HP Mute
D506
68 88 SP Mute
4
Pure Direct LED
13 15 85, 86
XL201
MVOL UP/DW
16MHz
OPERATION (2)
• See page 34 →
SCHEMATIC DIAGRAM
IC707 • See page 36 → IC8 OPERATION (1)
NJM2068MD SCHEMATIC DIAGRAM
MAIN (4) NJM4556AD
VR1 IC6 • See page 33 →
DOCK for Motor Driver SCHEMATIC DIAGRAM
iPod 9, 10 Muting Muting
Q5, Q7 Q6, Q8 PHONES
5 OPERATION (1)
M
• See page 33 → HP AMP

SCHEMATIC DIAGRAM
FM/AM IC201 RY2

IC10
Tuner
NJM2068MD L
Bass/Treble Control
FM/AM NJM2068MD SW2
Balance Volume
7.2MHz
Master Volume
Input Selector
Pure Direct SPEAKERS

VR501,502
LC78211
VR503
RY2
IC202
Muting
R
Q9, 10
DVD/CD
ANALOG IN
L/R
MD/TAPE
L/R POWER AMP
6 AUX/TV
L/R
R131 R133
REC OUT
MD/TAPE
L/R
Pure Direct
• See page 35 → SUBWOOFER OUT
IC4 MAIN (1) SCHEMATIC DIAGRAM
NJM2068MD
23
A B C D E F G H I J
RX-E810/RX-E410/NX-E800
POWER SECTION BLOCK DIAGRAM
• See page 35
MAIN (1) → SCHEMATIC DIAGRAM
Power D32
2 Transformer AC2
+B
C71
G
C70
Q33 -B
OPERATION (2)
-VP • See page 34
-VP
→ SCHEMATIC DIAGRAM
3 F1 IC9 Q701
RY1 D31
AC1 +5I +3.3V 3.3V
+5V +5I
F1 (U, C, G models) / C73
J1 (T, K, A, B, L, V models) GND GND
GND
MAIN (3)
• See page 36
• See page 37
→ SCHEMATIC DIAGRAM INPUT (2)
TE1 → SCHEMATIC DIAGRAM
4 D206 Q202
(U, C, T, A, B, G, L, V models) AC3
AC IN +12V +12 / +12_M
C220
GND
C224 Q203
IC1, 2, 3 Q2, 3 -12V -12
Power Detector
IC3
/Reset AC4
5 F1
D11
F2
Q4
D208
D5 Q204 +5CPU
T1 +10V
+5.5V
D209
6 RY1
D210 Q1
Q1 +5BAK
GND
MAIN (2)
• See page 36 • See page 37
→ SCHEMATIC DIAGRAM INPUT (1) → SCHEMATIC DIAGRAM
7
Power Relay
24
A B C D E F G H I J
RX-E810/RX-E410/NX-E800
1
■ PRINTED CIRCUIT BOARDS INPUT (2)
(CB201)
-VP
F2
F1
OPERATION (1) P.C.B. (Side A)
PRESET/TUNING PRESET/BAND AUTO/MAN'L MEMORY DISPLAY

P-RLY
CGND
REMOTE
CGND
+5CPU
KEY0
KEY1
ROT_A MIN HOUR TIMER TIME ADJ
ROT_B PHONES
FL_CK
FL_DT
/FL_CE
/FL_IC
3 TIMER_LED
HP_DET
/STANDBY
/TIMER
PD_LED
INPUT (1) INPUT

(CB200)
L R - + - + STANDBY/ON
BALANCE TREBLE BASS
HP_L
HL_R
T_FB_L
T_FB_R
T_IN_L
T_IN_R
T_L
T_R
4
E
E
E
E
E
E
E
MAIN (4)
(CB19)
OPERATION (1) P.C.B. (Side B) • Semiconductor Location

Ref no. Location
D501 H2
D502 H7
33 32
5 D503 H7
D504 G5
D505 G5
48 17
49 16
D506 C2
IC501 F5
Q501 E5
Q502 I6
64 1
Q503 D5
Q504 D5
Q505 D5
25
A B C D E F G H I J
RX-E810/RX-E410/NX-E800
OPERATION (2) P.C.B. (Side A) OPERATION (2) P.C.B. (Side B)
3 IP_L
8
14
E
14 9
IP_R
E
1 8
+12V 1
7
-12V
IGND
+5I
IP_RX
IP_PWR
IP_DET 8 5
IP_TX
+5CPU 1 4
CGND
4
INPUT (1)
(CB206)
DOCK
• Semiconductor Location
Ref no. Location
D705 H3
IC703 G3
IC704 H3
IC707 G4
6 Q701 H3
26
A B C D E F G H I J
RX-E810/RX-E410/NX-E800
1 Circuit No. U, C T, K, A, B, G L V
C76, C79, C125, C126 X O O X
C81, C82 X O O X
MAIN (1) P.C.B. MAIN (2) (CB1)
C116 X X O X
R142, R143, R813, R184 X O O X
(Side A) TO DVD-E810 X : NOT USED
(RX-E810 model)
O : USED/APPLICABLE
SYS_AD
SP_RLY
SYS_IO
TO CDX-E410
CGND
CGND
CGND
CGND
SGND
(RX-E410 model)
SUBWOOFER
2 OUT
L +/-
SPEAKERS
R +/-
4 5
3 1 8
INPUT (2)
(W200)
-12V
E
DGND
+12V
+12_M
4 PROT_1
-VP
SGND
E
SP_L
E
SP_R
E
HP_L
E
HP_R
+12V
+12V
+12V_M
-12V
-12V
IGND
DGND
+5I
HP_MUTE
PROT_TH
+5CPU
CGND
SP_MUTE
PROT_3
PROT_2
PROT_1
DGND
+12V_M
MAIN (4) (CB21) • Semiconductor Location
INPUT (1) (CB207)
INPUT (1) (CB202) Ref no. Location Ref no. Location
D13 F3 Q10 G7
Power Transformer
D14 G3 Q11 F3
MAIN (1) P.C.B. D15 F2 Q12 G3
(Side B) D16 F2 Q13 F3
D17 G2 Q14 G3
5 D18 G2 Q15 F3
D19 F2 Q16 G3
D20 G2 Q17 F2
D23 G2 Q18 G2
D24 H2 Q19 F2
D25 D3 Q20 G2
D26 D3 Q21 F2
D28 C2 Q22 F2
D29 E3 Q23 G2
D31 C3 Q24 G2
D32 D3 Q25A F2
6 D33 C3 Q25C F2
D34 D3 Q27A G2
IC7 G2 Q27C H2
IC8 H3 Q29 G2
IC9 D3 Q30 F2
Q5 H6 Q31 H2
Q6 H6 Q32 D3
Q7 H6 Q33 D3
Q8 H6 Q34 G2
Q9 F7 Q35 G2
27
A B C D E F G H I J
RX-E810/RX-E410/NX-E800
MAIN (2) P.C.B. (Side A) MAIN (3) P.C.B. (Side A) MAIN (4) P.C.B. (Side A)
U, C, T, A, B, G, L, V models
INPUT (1) INPUT (1)

(W201) (CB209)
2
MVOL_DW
SEL_R
P-DIRECT
SEL_L
+12V
-12V
+12V_M
MGND
INPUT (1) (CB205)
E
MAIN (1)
MVOL_UP
+5M (CB14)
+12V_M
/RESET
MGND
P_DET BR OPERATION (1)
CGND SGND (CB502)
SYS_AD SYS_AD
SP_RLY SP_RLY
SYS_IO SYS_IO T_R
P_RLY CGND E
+10V T_L
CGND E
3 CGND T_IN_R
E
CGND T_IN_L
GY E
AC OUTLET E
T_FB_R
T_FB_L
E
HP_R
E
HP_L
4
1 10
E
SP_L +
E M
SP_R
E
HP_L
E
14 1
HP_R
BR
5
MAIN (1)
(W8)
8 7
PURE DIRECT MIN MAX

AC IN
6 Ref no. Location
D5 C3
VOLUME D11 B5
GY D12 H4
Power Transformer IC1 B4
Circuit No. U, C T, K, A, B, L G V
IC2 B4
J1 X O X O IC3 B5
CB2, CB4 O X O X IC6 H4
F1 O X O X Q1 B4
R16 O X X X Q3 B3
J28 X O O X Q4 B5
7
X : NOT USED
O : USED/APPLICABLE
28
A B C D E F G H I J
RX-E810/RX-E410/NX-E800
MAIN (2) P.C.B. (Side B) MAIN (4) P.C.B. (Side B)

2
5 4
8 1
3
5 4
8 1
5 4
8 1
5 5 4
8 1
Ref no. Location
D1 B4
D2 B3
6 D3 B4
D4 B3
D6 B3
D7 B4
D8 B4
D9 B4
D10 B4
IC4 F3
IC5 F4
IC10 G5
IC11 G5
7 Q2 B3
29
A B C D E F G H I J
RX-E810/RX-E410/NX-E800
1
TUNER
TU_ST/MON
SADEV_CE
SADEV_CK
TU_ROUT
TU_LOUT
MAIN (2)
(W1)
+10V
SYS_AD
OPERATION (2)
SP_RLY
/RESET
SYS_IO
P_DET
NC
P_RLY
CGND
+10V
B, G models (CB702)
IP_PWR
+5M
INPUT (1) P.C.B. (Side A)
IP_DET
+5CPU
SADEV_DO
CGND
IP_RX
IP_TX
SADEV_DI
IGND
TU_MUTE
+12V
IP_R
-12V
IP_L
TU_STAT
+5I
E
E
TGND
RDS
2
PD_LED
/TIMER
/STANDBY HP_DET
TIMER_LED
/FL_IC
/FL_CE FL_DT
FL_CK ROT_B
ROT_A
KEY1 DVD/CD
KEY0 +5CPU
CGND REMOTE 15 16 L/R
CGND P_RLY
IN
3 OPERATION (1) L/R
(CB501)
MD/TAPE
MVOL_DW OUT
MVOL_UP
P-DIRECT
MGND
MGND
1 30 L/R
+12V_M
+12V_M
MAIN (4) AUX

(CB20) L/R
+12V_M
MGND
PROT_1
PROT_2
PROT_3
SP_MUTE
CGND
+5CPU
PROT_TH
HP_MUTE
+5I
DGND
IGND
-12V
-12V
+12V_M
+12V
+12V
4
+12V
E
MAIN (1) MAIN (1) SEL_R
(CB12)
(CB15) E MAIN (4)
SEL_L (CB18)
E
-12V
B, G models
Ref no. Location
INPUT (1) P.C.B. (Side B) D202 D6
5 D203 D6
D204 D6
12 1 D208 E5
51 50 D209 C5
D210 E5
13 24 D211 D5
31 D212 F5
30
60 D213 F6
61 IC200 D6
IC201 F6
IC202 G3
100 1
6 IC203 F5
Q204 D2
Q206 F2
Q207 F6
Q208 D7
8 5 Q209 D7
Q210 E3
RX-E810
Circuit No. RX-E410 1 4 Q211 E6
U, C, T, K, A, B, G L, V
PN202 X O X
R314 O O X
7 X : NOT USED
O : USED/APPLICABLE
30
A B C D E F G H I J
RX-E810/RX-E410/NX-E800
2
INPUT (2) P.C.B. (Side A) INPUT (2) P.C.B. (Side B)
Power Transformer
F2
F1
3
Ref no. Location
SGND
-VP D200 H5
PROT_1 D201 H4
5 +12_M D205 H5
+12V D206 D3
DGND
D207 H4
-VP
SGND Q200 E5
Q201 E4
Q202 E5
Q203 E4
MAIN (1)
(CB13)
F2
F1
-VP
OPERATION (1)
(W501)
6
31
RX-E810/RX-E410/NX-E800
■ PIN CONNECTION DIAGRAMS
• ICs • Diodes
BA50BC0T KIA7805API LB1641 LC72722PM LC78211 1SS133 1SS355 S1NB20 1A 200V S1NB60 1.0A 600V
1SS176 1SS380
1SS270A MA8030-L 2.9V
1SR139-400 MA8036-H 3.7V
MTZJ5.1B 5.1V MA8039-H 4.0V
MTZJ5.1C 5.1V MA8051-M 5.1V
MTZJ12C 12V Anode MA8056-M 5.6V
15 MTZJ22C 22V MA8068-M 6.8V +
10 Anode –
12 MA8091-M 9.1V
IN
24 MA8100-H 10.3V
30
1 OUT 1
MA8100-M 10V ~ 2 4
COM 1 Cathode ~
3 1 RB501V-40 1
Cathode UDZ6.2B 6.2V
LM61CIZ M30620MCP-A41FP M66003-0131FP MM74HCT08SJX

D5SBA20-4001 6A KBP103G 1.0A 200V
80 51 48 33
81 50 49 32
4 –
3
2 AC
100 31 7 1 +
64 17 14
+VS
VOUT 1 30 1 16 1
GND
NJM2068MD-TE2 NJM4556AD SN74LV32ANSR TC4013BP TLP421

• Transistors
2SA1015 Y 2SB1257 2SD1915F S,T 2SA1708 S,T
2SA949 O,Y 2SD2014 2SA1770 S,T
2SC1815 Y 2SK246 Y 2SC4488 S,T
2SC1890A D,E 2SK3850 2SC4614 S,T
2SC2229 O,Y 2SD1938F S,T
7
2SC3326 A,B
4 14 7
8 4 8 14
4 2
1 1
1 1 1
BC B
E
CB BC C
E E E
2SA1036KT146 P,Q,R 2SA1694 O,P,Y 2N5551C-AT

2SC2412K Q,R,S 2SC4467 O,P,Y 2N5401C-AT
DTA114EKA
DTC114EKA
DTC144EKA
C
E B
C
E B
B CE
32
A B C D E F G H I J K L M N
RX-E810/RX-E410/NX-E800
SCHEMATIC DIAGRAM
OPERATION 1/2
1
OPERATION (1)
FL DISPLAY
-15.4
-20.7
-20.8
-20.7
-20.8
-20.8
-20.8
-20.8
-20.8
-20.8
-20.8
-20.8
-20.8
-20.8
-20.8
-20.8
-20.5
-22.3
-15.9
-14.3
-15.9
-17.5
-15.8
-20.7
-22.3
-20.7
-14.3
-15.9
-22.3
-22.3
-20.7
-14.3
-15.9
-22.3
-20.7
-22.3
-14.3
-15.9
-20.7
-22.3
-22.3
-14.3
-12.6
-22.3
-22.3
-22.3
-14.3
-20.7
-15.8
-15.8
-15.8
-15.8
-15.4
2
Page 37 A8
to INPUT (2)_CB201
5.0
-22.3
-20.7
-14.3
-15.9
-22.3
-20.7
-22.3
-14.3
-15.9
-20.7
-22.3
-22.3
-14.3
-12.6
-22.3
-22.3 -22.3
-15.9 -22.3 -15.7
-14.3 -14.3
-20.7 -20.7
-19.1
-22.3 -15.8
-20.7 -15.8
-15.8 FL DRIVER -15.8
-17.5 -15.8
-19.1
5.0 -15.9
4 5.0
-14.3 2.2
-15.9 2.2 -22.5
4.9
-22.3 0
2.9
4.7
4.7 5.0
5.0
5.0 -20.7 4.7 2.9
4.7 0
-20.7
-20.8
-20.8
-20.8
-20.8
-20.8
-20.8
-20.8
-20.8
-20.8
-20.8
-20.8
-20.8
-20.7
-20.8
-20.7
0 -20.5
-22.5
0
BASS TREBLE BALANCE

INPUT L
INPUT
0 4.9 4.8
4.9
IC501: M66003-0131FP
FL display driver
3.4
Display code
RAM CGROM
(35 bit x 166) 44 SEG00
3.4 (8-bit x 60)
0
Code Segment 19 SEG25
write output 17 SEG26
circuit
dot data
CGROM 9 SEG34
CS 2 Serial data (35 bit x 16)
write
SCK 3 receive
Code/
0 SDATA 4 circuit
command
control 45 SEG35
circuit DIG11/
52
SEG42
8 51 DIG12/
SEG41
code Segment DIG13/
select 50
digit SEG40
select/ DIG14/
0 0 XIN 7 Clock output
49
SEG39
timing Display
generator clock controller scan pulse circuit 48 DIG15/
XOUT 6 SEG38
47 DIG16/
0 0 SEG37
46 DIG17/
SEG36
63 DIG00
Digit
RESET 1 output
Vcc1 8 circuit
53 DIG10
Vcc2 18
Vss 5
Vp 64
PHONES
9
Page 37 A2 Page 36 D9
to INPUT (1)_CB200 to MAIN (4)_CB19
10
★ All voltages are measured with a 10MΩ/V DC electronic volt meter.

★ Components having special characteristics are marked s and must be replaced
with parts having specifications equal to those originally installed.
★ Schematic diagram is subject to change without notice.
33
RX-E810/RX-E410/NX-E800
1 OPERATION 2/2
2
DOCK
11.2
3
0.1
0
Page 37 G2
to INPUT (1)_CB206
4
0
0.1
0
-11.1
5
3.4 5.0
3.8
3.8
3.4 0
0 0.4
0 0.4
0
6 0
0
0
2.8
2.8
4.9
2.9
2.9
0
0
0
0
0
0
4.9
0
0
3.4
3.4
4.9
7
8
OPERATION (2)
IC703: SN74LV32ANSR IC704: MM74HCT08SJX IC707: NJM2068MD-TE2

Quadruple 2-Input positive-OR gates Quadruple 2-Input AND gate Dual operational amplifier
9
1A 1 14 Vcc 1A 1 14 Vcc
OUT1 1 8 +VCC
1B 2 13 4B 1B 2 13 4B
–IN1 2 7 OUT2
+ – + –
1Y 3 12 4A 1Y 3 12 4A
+IN1 3 6 –IN2
2A 4 11 4Y 2A 4 11 4Y
–VCC 4 5 +IN2
2B 5 10 3B 2B 5 10 3B
2Y 6 9 3A 2Y 6 9 3A
GND 7 8 3Y GND 7 8 3Y
10

34
RX-E810/RX-E410/NX-E800
MAIN 1/2
1
Page 36 E9 Page 37 B7 Page 37 A8 Page 36 B5 Page 37 G7

to MAIN (4)_CB21 to INPUT (1)_CB202 to INPUT (2)_W200 to MAIN (2)_CB1 to INPUT (1)_CB207
5.0 10.2
10.2
AC 8.6
0
4.7 4.5
0 0
0 0
POWER TRANSFORMER
3
29.5
4.7
4.0 17.2
4.7
3.4
38.7
0 0
IC7: LM61CIZ
-23.1
Temperature sensor
0 0 0.1 0
4 -23.1
-38.6
-11.1 11.2
-22.4 -37.1 -37.9 -38.6
0.1 0.1
AC 57.6
0.9 4.9
0 TO DVD-E810 (RX-E810 model)
TO CDX-E410 (RX-E410 model)
0.1 0 0 0.1
-11.0 -11.0
38.9
5 38.2 38.5
-11.0 -11.0
HP AMP 37.6
1.1
38.7
38.7 0.1
38.4
0.1 0 0 0.1 0
1.1 38.4
0
0.5 0.5
38.4
0 0
1.1 0
IC8: NJM4556AD
1.1 0 Dual operational amplifier
-0.4
37.6 38.7 -1.1

-1.1 0
V+
8
0 0
-0.6
-0.6
-0.6 0
OUTPUT L 0
2, 6
-0.5 –INPUT OUTPUT
+INPUT 1, 7
-0.5
-1.1 -1.1 3, 5
6 0 0 -38.6
-37.5
-38.6
-37.5 0
-11.0
-38.1
V–
-38.1 4
0
-38.6
-38.1 IC9: KIA7805API (U, C, T, K, A, B, G models)

POWER AMP -38.4
0 Voltage regulator
-10.9 -38.1
1 INPUT
0.1 R22 R17 R23
-37.5
-38.6
-37.5 R1 Q11 Q11-1
0 0 Q15
7 -1.1
-1.1
-38.6
Q12
Q16
-0.5
Q14 R14
-0.5 R10 R15
0 Q17 Q19 R16
R19
-0.6
R12 3 OUTPUT
0
Q18 Q6 R20
-0.6 -0.6 Q1
R18
R11 R9
-1.1 Z1 R7 C1
0 0 R2 Q10
-1.1 Q2
37.6 0
Q7 R21
38.7 Q13 R3
Q4
-0.4
1.1 Q3 Q5 Q9 Q8
R13
1.1 0.1
R4 R5
38.4 R6 R8
0
0.5
2 COMMON (GND)
0.5
1.1 38.7
1.1 38.7
8 37.6
38.7
IC9: BA50BC0T (L, V models)

Low-dropout voltage regulator with low saturation
MAIN (1)
Vcc
Vref Driver
R2
R1
TSD OCP
9 1
Vcc
2
GND
3
OUT
10

35
RX-E810/RX-E410/NX-E800
1 MAIN 2/2
IC1, 2: TLP421 IC4, 5, 10, 11: NJM2068MD-TE2

Photo transistor Dual operational amplifier
Page 37 F2
to INPUT (1)_CB205
OUT1 1 8 +VCC
Anode 1 4 Collector
MAIN (3) –IN1 2
+ – + –
7 OUT2
+IN1 3 6 –IN2
Cathode 2 3 Emitter
–VCC 4 5 +IN2
IC3: TC4013BP
Dual D-type flip flop
(2) (2)
5.0
(2.8) RESET1 4
(0) (2) (2)
4.9 SET1 6 1 Q1
7.6
4.6 (0) DATA1 5
2 Q1
(2.8) (7.6) CL
0.9 CL
0 5.1 4.9
0.2 CL CL
3 (3.7) CLOCK1 3 CL
4.9 (0) CL
0 0
0 4.0
7.6
(2.2) (0)
POWER TRANSFORMER RESET2 10
(0) (0)
0 0.2 SET2 8 13 Q2
0 0 (0) (0)
4.0
DATA2 9
12 Q2
0 0 CL CL
0 0
CL CL
0.8 0.8 0
0 0 CLOCK2 11 CL
CL
VSS 7
0.1 0.1 10.2 10.2 1.1 1.0 1.0 2.2
VDD 14
4
2.3
10.2 0
IC6: LB1641
3.1 Motor driver
OUT 1
VCC 2
OUT 2
VCC 1
AC 5.0
P1
P2
3 2 8 10 9 7
SECONDARY PRIMARY MAIN (2)
PRE DRIVER
Page 35 F2 4 VZ
5 to MAIN (1)_CB14
IN 1 5 INPUT LOGIC 6 IN 2
GND 1
MAIN (4)
MASTER VOLUME
6 L
11.2 11.2
0.1
0.1 0
0.5 0.1
0.1
INPUT L 11.2
0.1
0.1
0.1
to INPUT (1)_W201
G7
Page 37
7
0.1
0.1
0.1
0.5 -11.1
0.1
0.1
0.1 0
-11.1
-11.1 0.1
VOLUME
PURE
DIRECT
8
0.6
OUTPUT L
11.2 0.8
0.1
11.1
0.1 11.1
0
0
to INPUT (1)_CB209
0
A6
1.0
0.8 0
Page 37
0.1
0 0.5
PURE DIRECT 0.1
0
INPUT L -11.1
9
Page 33 H9 Page 35 B2
to OPERATION (1)_CB502 to MAIN (1)_W8
10

36
RX-E810/RX-E410/NX-E800
INPUT
1 b
3
a
Page 36 B2 Page 34 L4
to MAIN (2)_W1 to OPERATION (2)_CB702 TUNER
IC203: LC72722PM
RDS signal processor
FL OUT
VREF
C IN
1 5 6
VDDA 3 PLL CLOCK 14 VDDD
2 REFERENCE
VOLTAGE
(57 kHz) RECOVERY
(1187.5 Hz)
VSSA 4 15 VSSD
VREF
57 kHz DATA
MPX IN 2 ANTIALIASING SMOOTHING
4.9 bpf
FILTER DECODER 19 RDS-ID
FILTER (SCF)
to OPEREATION (1)_CB501
5.5 5.5 10.3

4.9
DO 20
5.5 6.1
4.7 CL 21 18 SYNC
RAM ERROR CORRECTION SYNC / EC
DI 22 CCB (24 BLOCK DATA) (SOFT DECISION) CONTROLLER 24 SYR
B9
5.5 CE 23
T1 CLK (4.332 MHz)
7 MEMORY
11.2 9.6
Page 33
T2 8 CONTROL
6.1 TEST SYNC SYNC
T3 9 OSC/DIVIDER DETECT-1 DETECT-2
10.3 T4 10
11 16 17 13 12
X IN
X OUT
T5
T6
T7
3
4.7
4.7
4.7
11.2 10.3
10.5
0.4
0
0
0
0
0
0
0
0
0
0
0
0
0
4.7 0 11.2 0
0
0
4.8
4.8
5.0
0
4.7
4.7
4.4
0
4.7
4.7 0 0
4.9 0
0 4.7
4.8
0 4.8
MICROPROCESSOR
0
0
0
2.5
0
0 0 IC201: NJM2068MD-TE2
4.8 0
4.8
Dual operational amplifier
0
0.9 M30620MCP-A41FP 4.7
0.4 2.1
2.5 0
OUT1 1 8 +VCC
2.5 4.9
4 0.1 0
–IN1 2
+ – + –
7 OUT2
0
0.4
4.8 0 +IN1 3 6 –IN2
1 2
4.9 0
–VCC 4 5 +IN2
4.7 0
0.1 0
5.2
4.8
4.9
4.6
2.3
2.2
4.8
2.3
2.2
4.7
4.7
4.8
4.7
4.7 0
0
0
0
0
0
0
0
0
0
0.3
2.5
0
2.5
0
0 0
0 0
4.7 11.2
0 11.2
IC202: LC78211
Analog function switch
5 4.9 0 0 0 0 0 0 0 0
2.5 11.2 L1 1 30 R1
4.9 0 0 0
0.1
-11.0 0 L2 2 29 R2
0
L3 3 28 R3
0
4.9 L4 4 27 R4
0.1
LCOM1 5 26 RCOM1
L5 6 25 R5
0.1
0
L6 7 24 R6
LCOM2 8 23 RCOM2
-11.0
0 0 0 L7 9 22 R7
L8 10 21 R8
0 0 0 0 0 0 0 0 0
LCOM3 11 20 RCOM3
VDD 19 LEVEL SHIFTER
6 VSS 16 ZZ 14 D1
to MAIN (4)_CB20
LATCH
CONTROL
VEE 12
15
G9
RES 18 ZZ CL
SHIFT REGISTER
S 17 ZZ 13 CE
Page 36
INPUT L
INPUT (1)
IC200: M30620MCP-A41FP
Single-chip 16-bit cmos microcomputer
Page 35 D2
Page 36 G7 Page 35 G2
to MAIN (1)_CB12
to MAIN (4)_CB18 to MAIN (1)_CB15
8 8 8 8 8 8 8
7
to OPERATION (1)_W501
Port P0 Port P1 Port P2 Port P3 Port P4 Port P5 Port P6

POWER TRANSFORMER <VCC2 ports>(4)
Port P7
<VCC1 ports>
I3
Internal peripheral functions
8
A/D converter System clock
(10 bits X 8 channels generation circuit
Page 33
Timer (16-bit) Expandable up to 26 channels)
Port P8
AC 4.5 XIN-XOUT
18.4 Output (timer A): 5 UART or XCIN-XCOUT
7
Input (timer B): 6 clock synchronous serial I/O PLL frequency synthesizer
POINT 1 Pin 11 of IC200 POINT 2 Pin 13 of IC200 (8 bits X 3 channels) On-chip oscillator
<VCC1 ports>
11.2 Three-phase motor
Port P8_5
18.4
control circuit CRC arithmetic circuit (CCITT ) Clock synchronous serial I/O
(Polynomial : X 16+X12+X5+1) (8 bits X 2 channels)
18.4
12.5 12.5
M16C/60 series16-bit CPU core Memory
to MAIN (1)_CB13
12.5 0 0
Port P9
D2
R0H R0L SB ROM

Watchdog timer R1H R1L 128K
USP
8 (15 bits) R2
8
0 R3
ISP RAM
Page 35
-18.7
DMAC INTB 10K
0 AC 28.4 (2 channels) A0
PC
Port P10
A1
0 FB FLG
D/A converter
8
(8 bits X 2 channels) Multiplier
-12.4
-12.4
RX-E810 RX-E410
-12.4 -18.7
-18.7
-11.1 -18.7
INPUT (2) POINT 3 a / Pin9, b / Pin8 of CB205
+5M a a
/RESET b b
AC cable ON AC cable OFF AC cable ON

10

37
RX-E810/RX-E410/NX-E800
■ REPLACEMENT PARTS LIST

• ELECTRICAL COMPONENT PARTS
WARNING
● Components having special characteristics are marked s and must be replaced with parts having specifications
equal to those originally installed.
ABBREVIATIONS IN THIS LIST ARE AS FOLLOWS:
C.A.EL.CHP : CHIP ALUMI.ELECTROLYTIC CAP L.EMIT : LIGHT EMITTING MODULE

C.CE : CERAMIC CAP LED.DSPLY : LED DISPLAY
C.CE.ARRAY : CERAMIC CAP ARRAY LED.INFRD : LED,INFRARED
C.CE.CHP : CHIP CERAMIC CAP MODUL.RF : MODULATOR,RF
C.CE.ML : MULTILAYER CERAMIC CAP PHOT.CPL : PHOTO COUPLER
C.CE.M.CHP : CHIP MULTILAYER CERAMIC CAP PHOT.INTR : PHOTO INTERRUPTER
C.CE.SAFTY : RECOGNIZED CERAMIC CAP PHOT.RFLCT : PHOTO REFLECTOR
C.CE.TUBLR : CERAMIC TUBULAR CAP PIN.TEST : PIN,TEST POINT
C.CE.SMI : SEMI CONDUCTIVE CERAMIC CAP PLST.RIVET : PLASTIC RIVET
C.EL : ELECTROLYTIC CAP R.ARRAY : RESISTOR ARRAY
C.MICA : MICA CAP R.CAR. : CARBON RESISTOR
C.ML.FLM : MULTILAYER FILM CAP R.CAR.CHP : CHIP RESISTOR
C.MP : METALLIZED PAPER CAP R.CAR.FP : FLAME PROOF CARBON RESISTOR
C.MYLAR : MYLAR FILM CAP R.FUS : FUSABLE RESISTOR
C.MYLAR.ML : MULTILAYER MYLAR FILM CAP R.MTL.CHP : CHIP METAL FILM RESISTOR
C.PAPER : PAPER CAPACITOR R.MTL.FLM : METAL FILM RESISTOR
C.PLS : POLYSTYRENE FILM CAP R.MTL.OXD : METAL OXIDE FILM RESISTOR
C.POL : POLYESTER FILM CAP R.MTL.PLAT : METAL PLATE RESISTOR
C.POLY : POLYETHYLENE FILM CAP RSNR.CE : CERAMIC RESONATOR
C.PP : POLYPROPYLENE FILM CAP RSNR.CRYS : CRYSTAL RESONATOR
C.TNTL : TANTALUM CAP R.TW.CEM : TWIN CEMENT FIXED RESISTOR
C.TNTL.CHP : CHIP TANTALUM CAP R.CEMENT : CEMENT RESISTOR
C.TRIM : TRIMMER CAP SCR.BND.HD : BIND HEAD B-TIGHT SCREW
CN : CONNECTOR SCR.BW.HD : BW HEAD TAPPING SCREW
CN.BS.PIN : CONNECTOR,BASE PIN SCR.CUP : CUP TIGHT SCREW
CN.CANNON : CONNECTOR,CANNON SCR.TERM : SCREW TERMINAL
CN.DIN : CONNECTOR,DIN SCR.TR : SCREW,TRANSISTOR
CN.FLAT : CONNECTOR,FLAT CABLE SUPRT.PCB : SUPPORT,P.C.B.
CN.POST : CONNECTOR,BASE POST SURG.PRTCT : SURGE PROTECTOR
COIL.MX.AM : COIL,AM MIX SW.TACT : TACT SWITCH
COIL.AT.FM : COIL,FM ANTENNA SW.LEAF : LEAF SWITCH
COIL.DT.FM : COIL,FM DETECT SW.LEVER : LEVER SWITCH
COIL.MX.FM : COIL,FM MIX SW.MICRO : MICRO SWITCH
COIL,OUTPT : OUTPUT COIL SW.PUSH : PUSH SWITCH
DIOD.ARRAY : DIODE ARRAY SW.RT.ENC : ROTARY ENCODER
DIODE.BRG : DIODE BRIDGE SW.RT.MTR : ROTARY SWITCH WITH MOTOR
DIODE.CHP : CHIP DIODE SW.RT : ROTARY SWITCH
DIODE.VAR : VARACTOR DIODE SW.SLIDE : SLIDE SWITCH
DIOD.Z.CHP : CHIP ZENER DIODE TERM.SP : SPEAKER TERMINAL
DIODE.ZENR : ZENER DIODE TERM.WRAP : WRAPPING TERMINAL
DSCR.CE : CERAMIC DISCRIMINATOR THRMST.CHP : CHIP THERMISTOR
FER.BEAD : FERRITE BEADS TR.CHP : CHIP TRANSISTOR
FER.CORE : FERRITE CORE TR.DGT : DIGITAL TRANSISTOR
FET.CHP : CHIP FET TR.DGT.CHP : CHIP DIGITAL TRANSISTOR
FL.DSPLY : FLUORESCENT DISPLAY TRANS : TRANSFORMER
FLTR.CE : CERAMIC FILTER TRANS.PULS : PULSE TRANSFORMER
FLTR.COMB : COMB FILTER MODULE TRANS.PWR : POWER TRANSFORMER ASS’Y
FLTR.LC.RF : LC FILTER,EMI TUNER.AM : TUNER PACK,AM
GND.MTL : GROUND PLATE TUNER.FM : TUNER PACK,FM
RX-E810/RX-E410/
GND.TERM : GROUND TERMINAL TUNER.PK : FRONT-ENDTUNER PACK

HOLDER.FUS : FUSE HOLDER VR : ROTARY POTENTIOMETER
NX-E800
IC.PRTCT : IC PROTECTOR VR.MTR : POTENTIOMETER WITH MOTOR

JUMPER.CN : JUMPER CONNECTOR VR.SW : POTENTIOMETER WITH ROTARY SW
JUMPER.TST : JUMPER,TEST POINT VR.SLIDE : SLIDE POTENTIOMETER
L.DTCT : LIGHT DETECTING MODULE VR.TRIM : TRIMMER POTENTIOMETER
39
RX-E810/RX-E410/NX-E800
P.C.B. OPERATION
Ref. No. Part No. Description Markets Ref. No. Part No. Description Markets
* WH453900 P.C.B. OPERATION UCKBGLV * IC703 X4176A00 IC SN74LV32ANSR OR
* CB501 VU281800 CN 18P SE IC704 XZ013A00 IC MM74HCT08SJX 2-IN
CB502 VU281500 CN 15P SE 9604S IC707 X3505A00 IC NJM2068MD-TE2
CB702 VQ963500 CN.BS.PIN 14P * JK501 WH204400 JACK.MNI MSJ-035-18A GR
C501 US135100 C.CE.CHP 0.1uF 16V Q501 VV556400 TR 2SC2412K Q,R,S
C502-503 US064100 C.CE.CHP 0.01uF 50V B Q502-503 VV655700 TR.DGT DTC144EKA
C504 UM397100 C.EL 10uF 16V Q504 VV655400 TR.DGT DTC114EKA
C506-507 US135100 C.CE.CHP 0.1uF 16V Q505 WD974200 TR 2SA1036KT146 P,Q,R
C508 UA654100 C.MYLAR 0.01uF 50V J Q701 VV556400 TR 2SC2412K Q,R,S
C509 UM388330 C.EL 330uF 6.3V ST501 WA789600 SCR.TERM M3
C510 US135100 C.CE.CHP 0.1uF 16V ST701 WA789600 SCR.TERM M3
C511 US062100 C.CE.CHP 100pF 50V B * SW501 WH251700 SW.RT.ENC XREB12105PVB20FINA
C512 US064100 C.CE.CHP 0.01uF 50V B SW502-508 WD483100 SW.TACT SKRGAAD010
C513-514 UA654100 C.MYLAR 0.01uF 50V J U501 V8085300 L.DTCT GP1UA271X
C515 US064100 C.CE.CHP 0.01uF 50V B * V501 WH034300 FL.DSPLY 16-BT-133GNK
C516-517 VE326100 C.MYLAR 0.12uF 50V VR501 V3555600 VR B20KΩ
C518-519 UA654330 C.MYLAR 0.033uF 50V J VR502 V3555700 VR W25KΩ
C520 US044220 C.CE.CHP 0.022uF 25V B VR503 V3555800 VR MN100KΩ
C701 US062100 C.CE.CHP 100pF 50V B * WH241000 SHEET.FL BLUE UCKBGLV
C703-707 US062100 C.CE.CHP 100pF 50V B * WH241200 SHEET.FL ORANGE TA
C709 US135100 C.CE.CHP 0.1uF 16V * WH241600 SPACER.FL
C710-711 US062100 C.CE.CHP 100pF 50V B
C713 US062100 C.CE.CHP 100pF 50V B
C716-717 US062100 C.CE.CHP 100pF 50V B
C719 US062100 C.CE.CHP 100pF 50V B
C720 US135100 C.CE.CHP 0.1uF 16V
C721 US062100 C.CE.CHP 100pF 50V B
C723-724 US135100 C.CE.CHP 0.1uF 16V
C726 US062100 C.CE.CHP 100pF 50V B
C728 US062100 C.CE.CHP 100pF 50V B
C729-730 US135100 C.CE.CHP 0.1uF 16V
C734 US064100 C.CE.CHP 0.01uF 50V B
C740 US135100 C.CE.CHP 0.1uF 16V
C741 UR837470 C.EL 47uF 16V
C742-743 UR267100 C.EL 10uF 50V
C746-747 US062100 C.CE.CHP 100pF 50V B
C751-752 UA652390 C.MYLAR 390pF 50V J
C755-756 UR267100 C.EL 10uF 50V
C759 UR267100 C.EL 10uF 50V
C760 US135100 C.CE.CHP 0.1uF 16V
C761 UR267100 C.EL 10uF 50V
C762 US135100 C.CE.CHP 0.1uF 16V
C763-764 US062100 C.CE.CHP 100pF 50V B
C765 US135100 C.CE.CHP 0.1uF 16V
C766 UR866220 C.EL 2.2uF 50V
D501 VR711400 LED(gr) SLR-325MC
D502-503 VV220700 DIODE.SHOT RB501V-40
D504 VU990500 DIODE.ZENR MA8030-L 2.9V
* D505 VU991200 DIODE.ZENR MA8036-H 3.7V
D506 WG760400 LED SELK6E10C BLUE
D705 VU991500 DIODE.ZENR MA8039-H 4.0V
RX-E810/RX-E410/
IC501 X6386A00 IC M66003-0131FP

NX-E800
• Note on the OPERATION P.C.B.

Of the OPERATION P.C.B. part Nos., only the U, C, K, B, G, L, V models part Nos. are included in the table.
The only different part between the T, A models and U, C, K, B, G, L, V models parts is the sheet/FL that is attached
to the fluorescent character display tube. When a T, A models OPERATION P.C.B. becomes necessary, order a U,
C, K, B, G, L, V models OPERATION P.C.B. and a T, A models sheet/FL and replace the sheet/FL of the U, C, K, B,
G, L, V models OPERATION P.C.B. with the T, A models sheet/FL.
✻ New Parts ✻ New Parts

40
RX-E810/RX-E410/NX-E800
P.C.B. MAIN
* WH452600 P.C.B. MAIN UC * C46-47 WE100200 C.PP 22pF 630V
* WH452700 P.C.B. MAIN T C48 UR237100 C.EL 10uF 16V
* WH452800 P.C.B. MAIN K C49 US062100 C.CE.CHP 100pF 50V B
* WH452900 P.C.B. MAIN A C50 UT952220 C.PP 220pF 100V
* WH453000 P.C.B. MAIN B C51 UT952150 C.PP 150pF 100V
* WH453100 P.C.B. MAIN G C52 UU297100 C.EL 10uF 100V
* WH453200 P.C.B. MAIN L C53-54 UT952150 C.PP 150pF 100V
* WH453300 P.C.B. MAIN V C55 UU297100 C.EL 10uF 100V
CB1 VQ961100 CN.BS.PIN 8P C56 UT952150 C.PP 150pF 100V
CB2 WC050700 CLIP.FUSE EYF-52BCY UCG * C59 UR265220 C.EL 0.22uF 50V
CB4 WC050700 CLIP.FUSE EYF-52BCY UCG C60 UR266470 C.EL 4.7uF 50V
s CB5 VP245600 CN 2P C61-62 VR324700 C.MYLAR 0.022uF 100V
CB6-7 WC050700 CLIP.FUSE EYF-52BCY C63 UR267470 C.EL 47uF 50V
s CB8 VG879900 CN.BS.PIN 2P C64 UR266470 C.EL 4.7uF 50V
CB12 VQ963100 CN.BS.PIN 10P C65 UR218100 C.EL 100uF 6.3V
* CB13 LB918080 CN.BS.PIN 8P C66 UR867470 C.EL 47uF 50V
CB14-15 VQ962900 CN.BS.PIN 8P C67 VG287800 C.EL 330uF 16V
CB16 LB918020 CN.BS.PIN 2P C68 UT952100 C.PP 100pF 100V
CB17 LB932040 CN.BS.PIN 4P C69 UR238100 C.EL 100uF 16V
CB18 LB918070 CN.BS.PIN 7P * C70-71 WH632900 C.EL 5600uF 50V
CB19 VM859600 CN.BS.PIN 15P C72 US145100 C.CE.CHP 0.1uF 25V
CB20 VQ047100 CN.BS.PIN 7P * C73 UR739820 C.EL 8200uF 16V
CB21 VB390400 CN.BS.PIN 8P C74 VE326000 C.MYLAR 0.1uF 50V
CB22 LB918040 CN.BS.PIN 4P s C75 VR324900 C.MYLAR 0.1uF 100V
C1 UA653100 C.MYLAR 1000pF 50V J C76 UA654220 C.MYLAR 0.022uF 50V J TKABGL
C2 US064100 C.CE.CHP 0.01uF 50V B s C77 VR324900 C.MYLAR 0.1uF 100V
C3 UR266220 C.EL 2.2uF 50V C78 UN866220 C.EL 2.2uF 50V
C4 UU239330 C.EL 3300uF 16V C79 UA654220 C.MYLAR 0.022uF 50V J TKABGL
* C5 UT954100 C.PP 0.01uF 100V C80 US062100 C.CE.CHP 100pF 50V B
C6 UR266220 C.EL 2.2uF 50V C81-82 UA654100 C.MYLAR 0.01uF 50V J TKABGL
C7 UA654100 C.MYLAR 0.01uF 50V J C84 UA652100 C.MYLAR 100pF 50V J
C8 WB687100 C.POL.MTL 0.047uF 400V UCV C85 US064100 C.CE.CHP 0.01uF 50V B
C8 WC041600 C.PP 0.022uF 630V TAKBGL * C86 UR258100 C.EL 100uF 35V
C9 UR266100 C.EL 1uF 50V C87-88 UR267100 C.EL 10uF 50V
C10 UA653470 C.MYLAR 4700pF 50V J C89 UU266470 C.EL 4.7uF 50V
C11 WB696300 C.POL.MTL 0.1uF 400V UCV C90 UU266470 C.EL 4.7uF 50V
C11 WD257600 C.PP 0.047uF 800V TAKBGL C91 UT952100 C.PP 100pF 100V
s C12 WB121400 C.CE.SAFTY 0.01uF 295V C92 VG287800 C.EL 330uF 16V
C13-14 UT952100 C.PP 100pF 100V C93 US062100 C.CE.CHP 100pF 50V B
C15-16 US062100 C.CE.CHP 100pF 50V B C94 UR237100 C.EL 10uF 16V
C17-18 UU266470 C.EL 4.7uF 50V C95-99 US062100 C.CE.CHP 100pF 50V B
C19 UR238330 C.EL 330uF 16V C100-103 US062100 C.CE.CHP 100pF 50V B
C20 UR238330 C.EL 330uF 16V C104-105 UR237100 C.EL 10uF 16V
C21-22 UR237470 C.EL 47uF 16V C110-111 US063220 C.CE.CHP 2200pF 50V B
* C23-24 WE100300 C.PP 33pF 630V C112-113 UR237470 C.EL 47uF 16V
C25-26 UR266220 C.EL 2.2uF 50V C114-115 UU266470 C.EL 4.7uF 50V
C27-28 VG287800 C.EL 330uF 16V C116 UR266100 C.EL 1uF 50V LV
C29 UR266220 C.EL 2.2uF 50V C117 US135100 C.CE.CHP 0.1uF 16V
C30 UR266220 C.EL 2.2uF 50V C118-119 UU266470 C.EL 4.7uF 50V
C31 UN866100 C.EL 1uF 50V C120-121 US063220 C.CE.CHP 2200pF 50V B
C32 UA654100 C.MYLAR 0.01uF 50V J C123-124 UR238220 C.EL 220uF 16V
RX-E810/RX-E410/
C33 UR238470 C.EL 470uF 16V C125-126 UA654220 C.MYLAR 0.022uF 50V J TKABGL
NX-E800
C34-35 UU267100 C.EL 10uF 50V D1 VT332900 DIODE 1SS355

C36 UA652100 C.MYLAR 100pF 50V J D2 VT332900 DIODE 1SS355
C37-38 UA652220 C.MYLAR 220pF 50V J D3 VU995000 DIODE.ZENR MA8091-M 9.1V
C39 UA652100 C.MYLAR 100pF 50V J D4 VT332900 DIODE 1SS355
C40 VG287600 C.EL 100uF 25V s D5 VR253700 DIODE.BRG S1NB20 1A 200V
C41-42 UA653330 C.MYLAR 3300pF 50V J D6 VT332900 DIODE 1SS355
C43-44 UU268100 C.EL 100uF 50V D7 VU990500 DIODE.ZENR MA8030-L 2.9V
C45 US135100 C.CE.CHP 0.1uF 16V D8 VU993800 DIODE.ZENR MA8068-M 6.8V

41
RX-E810/RX-E410/NX-E800
P.C.B. MAIN and P.C.B. INPUT

D9 VU995400 DIODE.ZENR MA8100-M 10V s R44 HV753220 R.CAR.FP 2.2Ω 1/4W
D10 VT332900 DIODE 1SS355 * R49 WB633000 R.MTL.OXD 1KΩ 1/2W J
s D11 V4756800 DIODE S1NB60 1.0A 600V * R50 WB633000 R.MTL.OXD 1KΩ 1/2W J
D12 VG437400 DIODE.ZENR MTZJ5.1B 5.1V * R59 WB632200 R.MTL.OXD 220Ω 1/2W J
D13-18 VD631600 DIODE 1SS133,176 * R60 WB632200 R.MTL.OXD 220Ω 1/2W J
D19 VG437500 DIODE.ZENR MTZJ5.1C 5.1V * R61-62 WB633300 R.MTL.OXD 1.8KΩ 1/2W J
D20 VG437500 DIODE.ZENR MTZJ5.1C 5.1V R63-64 HV755100 R.CAR.FP 100Ω 1/4W
D23-24 VN008700 DIODE 1SS270A * R65-66 WB634800 R.MTL.OXD 33KΩ 1/2W J
D25 VG442200 DIODE.ZENR MTZJ22C 22V * R67-68 WB632600 R.MTL.OXD 470Ω 1/2W J
D26 VG440300 DIODE.ZENR MTZJ12C 12V R69 HF353220 R.CAR 2.2Ω 1/2W
D28 VG440300 DIODE.ZENR MTZJ12C 12V * R74 WB633500 R.MTL.OXD 2.7KΩ 1/2W J
D29 VU264200 DIODE 1SR139,400 * R75 WB632600 R.MTL.OXD 470Ω 1/2W J
s D31 WA653100 DIODE.BRG KBP103G 1.0A 200V * R76-77 WB632900 R.MTL.OXD 820Ω 1/2W J
s D32 VQ111400 DIODE.BRG D5SBA20-4001 6A * R78 WB632600 R.MTL.OXD 470Ω 1/2W J
D33-34 VD631600 DIODE 1SS133,176 * R79 WB633500 R.MTL.OXD 2.7KΩ 1/2W J
* s F1 WB220900 FUSE T3.5A 125V UC * R80-81 WB633000 R.MTL.OXD 1KΩ 1/2W J
s F1 VT942900 FUSE T2.5A 250V G R82-83 HV755100 R.CAR.FP 100Ω 1/4W
* s F2 WB220900 FUSE T3.5A 125V UCV R86-89 HV753470 R.CAR.FP 4.7Ω 1/4W
s F2 KB000750 FUSE.MNI T2A 250V TKABGL s R94-95 V3873200 R.CEMENT 0.22Ω 3W
s IC1-2 V8100500 PHOT.CPL TLP421 GR * s R104-105 WB625300 R.MTL.OXD 10Ω 1W J
s IC3 iG001180 IC TC4013BP FF s R121 HV755100 R.CAR.FP 100Ω 1/4W
IC4-5 X3505A00 IC NJM2068MD-TE2 * s R128 WB627100 R.MTL.OXD 330Ω 1W J
IC6 XF494A00 IC LB1641 R142-143 HV753220 R.CAR.FP 2.2Ω 1/4W TKABGL
IC7 X0515A00 IC LM61CIZ THERMAL R171-174 HV755100 R.CAR.FP 100Ω 1/4W
* IC8 XQ824A00 IC NJM4556AD OP AMP R183-184 HV753220 R.CAR.FP 2.2Ω 1/4W TKABGL
s IC9 X4928A00 IC KIA7805API 5V UCTKABG s RY1 V2712300 RELAY DC SDT-S-112LMR
IC9 X6520A00 IC BA50BC0T LV s RY2 V5966300 RELAY DS24D2-OS(M)
IC10-11 X3505A00 IC NJM2068MD-TE2 ST1 WA789600 SCR.TERM M3
JK1 V4273000 JACK.MINI MSJ-035-12D SW2 VV399900 SW.PUSH SPUN12
* PJ1 WH981900 JACK.PIN RCA-107AG-01 T1 XW606A00 TRANS.PWR UCV
PN1-2 V9637500 PIN L=70 #18 T1 XW608A00 TRANS.PWR TKABGL
Q1 iC1815I0 TR 2SC1815 Y s TE1 VU543100 OUTLET.AC 2P UC
Q2 VV655700 TR.DGT DTC144EKA s TE1 V5867400 OUTLET.AC 2P TV
Q3 iC1815I0 TR 2SC1815 Y s TE1 VT915000 OUTLET.AC 1P A
s Q4 WC741200 FET 2SK3850 s TE1 VU543400 OUTLET.AC 2P B
Q5 VZ725900 TR 2SD1938F S,T s TE1 VU543400 OUTLET.AC 2P GL
Q6 VZ725900 TR 2SD1938F S,T TE2 VY696300 TERM.SP 4P UCTABV
Q7 VZ725900 TR 2SD1938F S,T TE2 VY696400 TERM.SP 4P KGL
Q8 VZ725900 TR 2SD1938F S,T VR1 V7375500 VR.MTR A100KΩ RK16812MG
Q9 VD303700 TR 2SC3326 A,B WE774200 SCR.BND.HD 3x10 MFZN2W3
Q10 VD303700 TR 2SC3326 A,B
Q11-14 VP883100 TR 2SC1890A D,E
Q15-16 V3966800 TR 2SA949 O,Y
s Q17-18 VK432900 TR 2SD1915F S,T * WH453500 P.C.B. INPUT UC
s Q19 VR325600 TR 2SC2229 O,Y * WH453600 P.C.B. INPUT TKA
s Q20 VR325600 TR 2SC2229 O,Y * WH453700 P.C.B. INPUT BG(E810)
s Q21 V4096100 TR 2SC4614 S,T * WH456900 P.C.B. INPUT BG(E410)
s Q22-23 V4096000 TR 2SA1770 S,T * WH453800 P.C.B. INPUT LV
s Q24 V4096100 TR 2SC4614 S,T CB200 VP573800 CN.BS.PIN 18P
s Q25A iX615750 TR 2SA1694 O,P,Y CB201 VB858200 CN.BS.PIN 3P
Q25C iX615760 TR 2SC4467 O,P,Y CB202 VQ961300 CN.BS.PIN 10P
RX-E810/RX-E410/
s
s Q27A iX615750 TR 2SA1694 O,P,Y CB203 LB918050 CN.BS.PIN 5P
NX-E800
s Q27C iX615760 TR 2SC4467 O,P,Y CB204 VQ047200 CN.BS.PIN 9P

Q29 WC397700 TR 2N5401C-AT CB205 VB390500 CN.BS.PIN 9P
s Q30-31 WC398400 TR 2N5551C-AT CB206 VQ961700 CN.BS.PIN 14P
s Q32 VP872700 TR 2SC4488 S,T CB207 VQ961100 CN.BS.PIN 8P
s Q33 iA1015I0 TR 2SA1015 Y CB208 VM923600 CN.BS.PIN 13P
Q34-35 WC398400 TR 2N5551C-AT CB209 VQ047100 CN.BS.PIN 7P
s R16 V6730000 R.CAR. 2.2MΩ 1/2W UC C200 US062100 C.CE.CHP 100pF 50V B
R43 HV754100 R.CAR.FP 10Ω 1/4W C201 US135100 C.CE.CHP 0.1uF 16V

42
RX-E810/RX-E410/NX-E800
P.C.B. INPUT
C202 US062100 C.CE.CHP 100pF 50V B D213 VU993000 DIODE.ZENR MA8056-M 5.6V BG
C203 US135100 C.CE.CHP 0.1uF 16V * IC200 X8212A00 IC CPU M30620MCP-A41FP (MASK ROM)
C204-206 US062100 C.CE.CHP 100pF 50V B IC201 X3505A00 IC NJM2068MD-TE2
C207 US135100 C.CE.CHP 0.1uF 16V IC202 XP894A00 IC LC78211
C208-215 US062100 C.CE.CHP 100pF 50V B IC203 X0082A00 IC LC72722PM BG
C216-217 UU238100 C.EL 100uF 16V PJ201-202 V9796700 JACK.PIN 4P MSP-244V1-03 GI
C218-219 UR267100 C.EL 10uF 50V PN201 V9637500 PIN L=70 #18
* C220 UU249470 C.EL 4700uF 25V PN202 V9637500 PIN L=70 #18 LV
* C220 UU249470 C.EL 4700uF 25V UCTKABG s Q200 WF691400 TR 2SD2014
* C220 WH931300 C.EL 4700uF 25V LV Q201 WF691300 TR 2SB1257
C221 UU249330 C.EL 3300uF 25V UCTKABG Q202-203 iE102620 FET 2SK246 Y
* C221 WH931200 C.EL 3300uF 25V LV Q204 VP872700 TR 2SC4488 S,T
C222 US135100 C.CE.CHP 0.1uF 16V s Q206 VP872700 TR 2SC4488 S,T
C223 US061330 C.CE.CHP 33pF 50V B s Q207 VV556400 TR 2SC2412K Q,R,S BG
C224-225 VR324900 C.MYLAR 0.1uF 100V Q208-209 VV655000 TR.DGT DTA114EKA
C226-227 US061270 C.CE.CHP 27pF 50V B Q210 VP872600 TR 2SA1708 S,T
C228-229 US135100 C.CE.CHP 0.1uF 16V Q211 VV655400 TR.DGT DTC114EKA
C230 UR237100 C.EL 10uF 16V s R202-203 HV755100 R.CAR.FP 100Ω 1/4W
C231 UB446100 C.CE.CHP 1uF 16V s R205-206 HV753470 R.CAR.FP 4.7Ω 1/4W
C232 UR219100 C.EL 1000uF 6.3V R224 R.CHP 2.7KΩ 1/16W J UC
C233 UR218470 C.EL 470uF 6.3V R224 R.CHP 47KΩ 1/16W J TKA
C235 WB165500 C.EL 0.33F 5.5V R224 R.CHP 0Ω 1/16W J BG
C236 UM397100 C.EL 10uF 16V R224 R.CHP 15KΩ 1/16W J LV
C237-240 US061330 C.CE.CHP 33pF 50V B R281 R.CHP 3.3KΩ 1/16W J BG
C241 UM397470 C.EL 47uF 50V R286 R.CHP 100KΩ 1/16W J BG
C242-243 VG287200 C.EL 10uF 50V R314 R.CHP 4.7KΩ 1/16W J (E810)
C244 VE326000 C.MYLAR 0.1uF 50V XL200 VQ328900 RSNR.CRYS 32.768KHz
C245 VG287500 C.EL 47uF 50V XL201 WB213000 RSNR.CE 16.0MHz
C246 UR267330 C.EL 33uF 50V XL202 V3930900 RSNR.CRYS 4.332MHz BG
C247 UR266220 C.EL 2.2uF 50V
C248 VE326000 C.MYLAR 0.1uF 50V
C249-250 VG287200 C.EL 10uF 50V
C251 VG287500 C.EL 47uF 50V
s C252 UR267330 C.EL 33uF 50V
s C253 UR266220 C.EL 2.2uF 50V BG
C254 UR267330 C.EL 33uF 50V BG
C255 UA652100 C.MYLAR 100pF 50V J
C256 UR237470 C.EL 47uF 16V BG
C257 US062330 C.CE.CHP 330pF 50V B BG
C258 UA652100 C.MYLAR 100pF 50V J
C259 UR237470 C.EL 47uF 16V BG
C260 US062330 C.CE.CHP 330pF 50V B BG
C261 UR237470 C.EL 47uF 16V BG
C262-263 US061270 C.CE.CHP 27pF 50V B BG
C264 US135100 C.CE.CHP 0.1uF 16V BG
C265-270 UA652100 C.MYLAR 100pF 50V J
C271-272 FG651470 C.CE 47pF 50V
C273-274 UB446100 C.CE.CHP 1uF 16V
C275-276 UA353220 C.MYLAR 2200pF 50V
C277-278 VG287500 C.EL 47uF 50V
C279-281 US062100 C.CE.CHP 100pF 50V B
RX-E810/RX-E410/
D200-201 VU172100 DIODE.ZENR UDZS6.2B 6.2V

NX-E800
D202-204 VU992600 DIODE.ZENR MA8051-M 5.1V

D205 VU172100 DIODE.ZENR UDZS6.2B 6.2V
s D206 WA653100 DIODE.BRG KBP103G 1A 200V
D208-209 VT332900 DIODE 1SS355
D210 VV833200 DIODE 1SS380
D212 VU995500 DIODE.ZENR MA8100-H 10.3V

43
RX-E810/RX-E410/NX-E800
Chip Resistors
● The chip resistor is not supplied as a replacement part.
* When a chip resistor is necessary, use the following part.
AAX60720: CHIP RESISTOR SAMPLE BOOK
R.CHP 0Ω 1/16W J
R.CHP 2.2Ω 1/16W J
R.CHP 33Ω 1/16W J
R.CHP 47Ω 1/16W J
R.CHP 75Ω 1/16W J
R.CHP 100Ω 1/16W J
R.CHP 270Ω 1/16W J
R.CHP 330Ω 1/16W J
R.CHP 390Ω 1/16W J
R.CHP 470Ω 1/16W J
R.CHP 680Ω 1/16W J
R.CHP 1KΩ 1/16W J
R.CHP 1.8KΩ 1/16W J
R.CHP 10KΩ 1/16W J
R.CHP 12KΩ 1/16W J
R.CHP 15KΩ 1/16W J
R.CHP 27KΩ 1/16W J
R.CHP 30KΩ 1/16W J
R.CHP 33KΩ 1/16W J
R.CHP 36KΩ 1/16W J
R.CHP 39KΩ 1/16W F
R.CHP 47KΩ 1/16W J
R.CHP 56KΩ 1/16W J
R.CHP 100KΩ 1/16W J
R.CHP 1MΩ 1/16W J
RX-E810/RX-E410/
NX-E800

44
RX-E810/RX-E410/NX-E800
Carbon Resistors
Value 1/4W Type Part No. 1/6W Type Part No. Value 1/4W Type Part No. 1/6W Type Part No.
1.0 Ω HJ35 3100 HF85 3100 10 kΩ HF45 7100 HF45 7100
1.8 Ω HJ35 3180 ❊ 11 kΩ HF45 7110 HF45 7110
2.2 Ω HJ35 3220 HF85 3220 12 kΩ HJ35 7120 HF85 7120
3.3 Ω HJ35 3330 HF85 3330 13 kΩ HF45 7130 HF45 7130
4.7 Ω HJ35 3470 HF85 3470 15 kΩ HF45 7150 HF45 7150
5.6 Ω HJ35 3560 HF85 3560 18 kΩ HF45 7180 HF45 7180
10 Ω HF45 4100 HF45 4100 22 kΩ HF45 7220 HF45 7220
15 Ω HJ35 4150 HF85 4150 24 kΩ HF45 7240 HF45 7240
22 Ω HF45 4220 HF45 4220 27 kΩ HJ35 7270 HF85 7270
27 Ω HJ35 4270 HF85 4270 30 kΩ HF45 7300 HF45 7300
33 Ω HF45 4330 HF45 4330 33 kΩ HF45 7330 HF45 7330
39 Ω HJ35 4470 HF85 4390 36 kΩ HF45 7360 HF45 7360
47 Ω HF45 4470 HF45 4470 39 kΩ HF45 7390 HF45 7390
56 Ω HF45 4560 HF45 4560 47 kΩ HF45 7470 HF45 7470
68 Ω HF45 4680 HF45 4680 51 kΩ HF45 7510 HF45 7510
75 Ω HF45 4750 HF45 4750 56 kΩ HF45 7560 HF45 7560
82 Ω HF45 4820 HF45 4820 62 kΩ HF45 7620 HF45 7620
91 Ω HF45 4910 HF45 4910 68 kΩ HF45 7680 HF45 7680
100 Ω HF45 5100 HF45 5100 82 kΩ HF45 7820 HF45 7820
110 Ω HJ35 5110 HF85 5110 91 kΩ HF45 7910 HF45 7910
120 Ω HF45 5120 HF45 5120 100 kΩ HF45 8100 HF45 8100
150 Ω HF45 5150 HF45 5150 110 kΩ HF45 8110 HF45 8110
160 Ω HJ35 5160 ❊ 120 kΩ HF45 8120 HF45 8120
180 Ω HF45 5180 HF45 5180 150 kΩ HF45 8150 HF45 8150
200 Ω HF45 5200 HF45 5200 180 kΩ HF45 8180 HF45 8180
220 Ω HF45 5220 HF45 5220 220 kΩ HJ35 8220 HF85 8220
270 Ω HF45 5270 HF45 5270 270 kΩ HF45 8270 HF45 8270
330 Ω HF45 5330 HF45 5330 300 kΩ HF45 8300 HF45 8300
390 Ω HF45 5390 HF45 5390 330 kΩ HF45 8330 HF45 8330
430 Ω HF45 5430 HF45 5430 390 kΩ HJ35 8390 HF85 8390
470 Ω HF45 5470 HF45 5470 470 kΩ HF45 8470 HF45 8470
510 Ω HF45 5510 HF45 5510 560 kΩ HJ35 8560 HF85 8560
560 Ω HF45 5560 HF45 5560 680 kΩ HJ35 8680 HF85 8680
680 Ω HF45 5680 HF45 5680 820 kΩ HJ35 8820 HF85 8820
820 Ω HF45 5820 HF45 5820 1.0 MΩ HF45 9100 HF45 9100
910 Ω HF45 5910 HF45 5910 1.2 MΩ HJ35 9120 ❊
1.0 kΩ HF45 6100 HF45 6100 1.5 MΩ HJ35 9150 HF85 9150
1.2 kΩ HF45 6120 HF45 6120 1.8 MΩ HJ35 9180 HF85 9180
1.5 kΩ HF45 6150 HF45 6150 2.2 MΩ HJ35 9220 HF85 9220
1.8 kΩ HF45 6180 HF45 6180 3.3 MΩ HJ35 9330 HF85 9330
2.0 kΩ HJ35 6200 HF85 6200 3.9 MΩ HJ35 9390 ❊
2.2 kΩ HF45 6220 HF45 6220 4.7 MΩ HJ35 9470 HF85 9470
2.4 kΩ HJ35 6240 HF85 6240
2.7 kΩ HF45 6270 HF45 6270
3.0 kΩ HF45 6300 HF45 6300
3.3 kΩ HF45 6330 HF45 6330
1/4W Type
HF45
3.6 kΩ HJ35 6360 HF85 6360
1/4W Type 1/6W Type
3.9 kΩ HF45 6390 HF45 6390
HJ35 HF85
4.7 kΩ HF45 6470 HF45 6470 10mm
5mm
5.1 kΩ HF45 6510 HF45 6510
5.6 kΩ HF45 6560 HF45 6560
6.8 kΩ HF45 6680 HF45 6680
8.2 kΩ HF45 6820 HF45 6820
9.1 kΩ HF45 6910 HF45 6910
❊ : Not available
45
A B C D E F G H I J
RX-E810/RX-E410/NX-E800
1
• RX-E810/RX-E410 OVERALL ASS’Y
146
146
B, G models 2-103
116
121 12
116
2-112 11
5 (2) 200 RX-E810
2 141
146
2-106 10
145 103
2-1 (2)
141
150 200-1
201 RX-E410
141
3 2-112
101
2-1 (1)
145
25
1-1 (2)
150 201-1
2-105
202 U, C, T, L, V models
4
1-115 1-116
1-103 LEFT
2-107 22
2-111 14
2-110 202 K, A, B, G models
149
2-107 2-111 2-102
1-1 (1)
120
2-1 (4) 15
1-11 203
5
1-104 204
1-10 144 5 (1)
120
1-107
144
1-108
1-109
1-106
U, C, T, A, B, G, L, V models
1-105 143
115
103
1-117
113
6 1-102
112 1-115 110
111 160
110 144
149
1-101 122
144
142 2-1 (3)
1-103 RIGHT
• Note on the OPERATION P.C.B.

Of the OPERATION P.C.B. (1-1) part Nos., only the U, C, K, B, G, L, V models part Nos. are included in the table.
The only different part between the T, A models and U, C, K, B, G, L, V models parts is the sheet/FL that is attached to the fluorescent
7 character display tube. When a T, A models OPERATION P.C.B. becomes necessary, order a U, C, K, B, G, L, V models OPERATION
P.C.B. and a T, A models sheet/FL and replace the sheet/FL of the U, C, K, B, G, L, V models OPERATION P.C.B. with the T, A models
sheet/FL.
46
RX-E810/RX-E410/NX-E800
Ref. No. Part No. Description Remarks Markets Ref. No. Part No. Description Remarks Markets
* 1-1 WH453900 P.C.B. ASS'Y OPERATION UCKBGLV 14 MF113100 FLEXIBLE FLAT CABLE 13P 100mm P=1.25
1-10 MF115140 FLEXIBLE FLAT CABLE 15P 140mm P=1.25 * 15 MF107080 FLEXIBLE FLAT CABLE 7P 80mm P=1.25
* 1-11 MF118180 FLEXIBLE FLAT CABLE 18P 180mm P=1.25 22 WB877300 AM/FM TUNER FAE381-A07F UCTLV
* 1-101 WH237400 FRONT PANEL E810GD 22 WB877400 AM/FM TUNER FAE481-E07F KABG
* 1-101 WH325800 FRONT PANEL E810BL 25 WB408000 BINDING TIE GT-100M HUA WEI
* 1-101 WH237500 FRONT PANEL E810SI * 101 WH242500 TOP COVER GD
* 1-101 WH237700 FRONT PANEL E410BL * 101 WJ040400 TOP COVER BL
* 1-101 WH237800 FRONT PANEL E410SI * 101 WH242600 TOP COVER SI UCKLV
* 1-102 WH228400 SUB PANEL GD * 101 WJ040200 TOP COVER SI BG
* 1-102 WH376500 SUB PANEL BL * 103 WH198700 REAR PANEL E810 UC
* 1-102 WH228500 SUB PANEL SI * 103 WH249800 REAR PANEL E810 T
* 1-103 WH240600 PANEL SIDE * 103 WH231200 REAR PANEL E810 K
* 1-104 WH242700 WINDOW PANEL * 103 WH231800 REAR PANEL E810 A
* 1-105 WH235600 ESCUTCHOEN D16 GD * 103 WH232000 REAR PANEL E810 B
* 1-105 WH336500 ESCUTCHOEN D16 BL * 103 WH232100 REAR PANEL E810 G
* 1-105 WH235700 ESCUTCHOEN D16 SI * 103 WH232200 REAR PANEL E810 L
* 1-106 WH235400 ESCUTCHOEN D15 GD * 103 WH231100 REAR PANEL E810 V
* 1-106 WH333000 ESCUTCHOEN D15 BL * 103 WH232600 REAR PANEL E410 B
* 1-106 WH235500 ESCUTCHOEN D15 SI * 103 WH232400 REAR PANEL E410 G
* 1-107 WH240500 LENS RC GD, SI * 110 WH239500 LEG
* 1-107 WH347900 LENS RC BL * 111 WH239600 KNOB D28 VOLUME GD
* 1-108 WH240400 LENS LED * 111 WH347300 KNOB D28 VOLUME BL
* 1-109 WH250100 BUTTON PURE DIRECT * 111 WH239700 KNOB D28 VOLUME SI
1-115 VQ368600 PUSH RIVET P3555-B * 112 WH239000 KNOB D14.5 INPUT GD
1-116 WE774800 BIND HEAD P-TIGHT SCREW 3x8 MFZN2W3 * 112 WH347100 KNOB D14.5 INPUT BL
* 1-117 WF266800 FLAT HEAD B-TIGHT SCREW 3x8 MFZN2B3 * 112 WH239100 KNOB D14.5 INPUT SI
* 2-1 WH452600 P.C.B. ASS'Y MAIN UC * 113 WH238200 KNOB BASS,TREBLE,BALANCE GD
* 2-1 WH452700 P.C.B. ASS'Y MAIN T * 113 WH325400 KNOB BASS,TREBLE,BALANCE BL
* 2-1 WH452800 P.C.B. ASS'Y MAIN K * 113 WH238300 KNOB BASS,TREBLE,BALANCE SI
* 2-1 WH452900 P.C.B. ASS'Y MAIN A 115 VQ368600 PUSH RIVET P3555-B
* 2-1 WH453000 P.C.B. ASS'Y MAIN B * 116 WJ087600 RIVET TOP BL G
* 2-1 WH453100 P.C.B. ASS'Y MAIN G * 116 WH487900 RIVET TOP SI BG
* 2-1 WH453200 P.C.B. ASS'Y MAIN L * 120 WH242000 SUPPORT H8
* 2-1 WH453300 P.C.B. ASS'Y MAIN V * 121 WH486500 SHEET TOP BG
* 2-102 WH231700 SUPPORT TR * 122 WH193400 SHEET BARRIER
* 2-103 WH242100 SUPPORT IC 141 WE774100 BIND HEAD BONDING B-T. SCREW 3x8 MFZN2B3
* 2-105 WB221700 RADIATION SHEET 19x24 142 WE774200 BIND HEAD B-TIGHT SCREW 3x10 MFZN2W3
* 2-106 WH235200 DAMPER 6x170x2 143 WE774800 BIND HEAD P-TIGHT SCREW 3x8 MFZN2W3 UCTABGLV
* 2-107 WH634800 DAMPER 6x14x8 144 WF002600 PW HEAD B-TIGHT SCREW 3x8 MFZN2W3
2-110 VQ368600 PUSH RIVET P3555-B 145 WE774600 SCREW IC 3x18 MFZN2W3
2-111 WE774600 SCREW IC 3x18 MFZN2W3 146 WF821300 BIND HEAD S-TIGHT SCREW 4x7 MFZN2W3
2-112 WF002600 PW HEAD B-TIGHT SCREW 3x8 MFZN2W3 * 149 WF266800 FLAT HEAD B-TIGHT SCREW 3x8 MFZN2B3
* 5 WH453500 P.C.B. ASS'Y INPUT E810 UC 150 VY712800 PW HEAD B-TIGHT SCREW 3x8-8 MFNI33 GD, SI
* 5 WH453600 P.C.B. ASS'Y INPUT E810 TKA * 150 WE975300 PW HEAD B-TIGHT SCREW 3x8 MFZN2B3 BL
* 5 WH453700 P.C.B. ASS'Y INPUT E810 BG * 160 WJ081800 DAMPER 15x70 t=1.5
* 5 WH453800 P.C.B. ASS'Y INPUT E810 LV
* 5 WH456900 P.C.B. ASS'Y INPUT E410 BG ACCESSORIES
* s 10 X8038A00 POWER TRANSFORMER UCV * 200 WH217700 REMOTE CONTROL RRC4001-1529E E810 UCTKALV
* s 10 X8039A00 POWER TRANSFORMER TK * 200 WH217800 REMOTE CONTROL RRC4001-1530E E810 BG
* s 10 X8040A00 POWER TRANSFORMER AL 200-1 AAX57560 BATTERY COVER 103RRS-141-07L
* s 10 X8041A00 POWER TRANSFORMER BG * 201 WH256400 REMOTE CONTROL RRS4004-1001E E410 BG
s 11 WB120500 POWER CABLE ME301P/TER UC 201-1 AAX57560 BATTERY COVER 103RRS-141-07L
s 11 WB120600 POWER CABLE 2m T 202 WB212500 INDOOR FM ANTENNA 1.4m 1pc UCTLV
s 11 WC753000 POWER CABLE 2m K 202 WB212400 INDOOR FM ANTENNA 1.4m 1pc KABG
s 11 WC743700 POWER CABLE 2m A 203 WB212600 AM LOOP ANTENNA 1.0m 1pc
s 11 WB212200 POWER CABLE 2m B * 204 WH469200 SYSTEM CONTROL CABLE 2P 600mm 1pc
s 11 WB212300 POWER CABLE 2m GL BATTERY UM-3 2pcs
s 11 WC992700 POWER CABLE 2m V
12 V2438700 CORD STOPPER 10P1
47
A B C D E F G H I J
RX-E810/RX-E410/NX-E800
1
• NX-E800 OVERALL ASS’Y
Ref. No. Part No. Description Remarks Markets

* 1 WH629500 CABINET ASS'Y LC
* 1 WH245200 CABINET ASS'Y BL
12 1-12 CB605250 HOLDER
7
13 * 2 WH629600 FRONT GRILLE ASS'Y LC
7-1 * 2 WH245300 FRONT GRILLE ASS'Y BL
2
3 XW275B00 DRIVER TWEETER 2.5cm 5Ω JA05U3
7-3 4 XW276C00 DRIVER WOOFER 13cm 6Ω JA1360
21 7 V9509800 NETWORK ASS'Y
3
7-2 7-1 V6055400 ELECTROLYTIC CAPACITOR 8.2uF 63V C11
7-2 V6367500 ELECTROLYTIC CAPACITOR 3.3uF 63V C12
22
7-3 V9507500 CEMENT RESISTOR 2.7Ω 5W R11
30
12 V5361400 TERMINAL CAP S06E RED
2 13 V5361500 TERMINAL CAP S06E BLACK
3 22 21 WE963200 FLAT HEAD WOOD SCREW 3.5x20 MFZN2B3
* 22 WF824200 HEXAGON HEAD WOOD SCREW 4x25 MFZN2B3
ACCESSORIES
30 V9826900 SPEAKER CABLE 4m 1pc
1
1-12
4
0.27mH
L12
TWEETER
R11 +C12
2.7ohms/5W 3.3uF/63V
8.2uF/63V
+C11
WOOFER
INPUT
L11
1.0mH
7
✻ New Parts
48
A B C D E F G H I J
RX-E810/RX-E410/NX-E800
1
■ REMOTE CONTROL WH217700: RX-E810 (U, C, T, K, A, L, V models)
WH217800: RX-E810 (B, G models)
<JP1•JP2>
• SCHEMATIC DIAGRAM JP1 X
• KEY CODE
Key Key Common DVD/CD TUNER ACX/TV DOCK TAPE/MD
JP2 X
No. Label code Function code Function code Function code Function code Function code
1 STANDBY/ON 78-0F <– <– <– <– <– <– <– <– <– <–
IC1 JP1 JP2

2
3
TV POWER
1
–
– 1 7C-94 P1 78-11
TV POWER : 50-17
– – –
1 P0D2 P1A2 30 4 2 – 2 7C-95 P2 78-12 – – –
2 5 3 – 3 7C-96 P3 78-13 – – –
2 P0D3 P0D1 29 6 4 – 4 7C-97 P4 78-14 – – –
7 5 – 5 7C-98 P5 78-15 – – –
3 P1B0/INT P0D0 28
8 6 – 6 7C-99 P6 78-16 – – –
µPD17241MC-422-5A4-E1-A
+ C1
4 P0E0 P0C3 27 3.0 V 9 7 – 7 7C-9A P7 78-17 – – –
47 µF 10 8 – 8 7C-9B P8 78-18 – – –
R1 1
2 5 P0E1 P0C2 26 11 9 – 9 7C-9C – – – –
2 ohms (1/4W) 12 0 – 0 7C-93 – – – –
SW1
3 6 P0E2 P0C1 25
D1 13 SCAN – SCAN 7C-E2 – – – –
SW1:NOT USE 7 24 14 DIMMER 78-BA – – – – –
M1E-554A2 P0E3 P0C0
R2 T3 15 TV CH + – TV CH + : 50-19
8 REM P0B3 23 8
6
16
REPEAT
24
SKIP -
32 40
VOLUME +
48
SUBTITLE 16 REPEAT – REPEAT 7C-A3 – – REPEAT 7F01-45BA –
(MEMORY) (PRESET -)
Q1 27 ohms
C2 9 22 7 15 23 31 39 47 17 A-B – A-B 7C-A4 – – – –
3 2SD1781k VDD P0B2 5 TV CH + SHUFFLE SLEEP DOCK
(START) (PRESET +) (i Pod)
18 TV CH - – TV CH - : 50-18
0.1 µF 10 21 6 14 22 30 38 46
XOUT P0B1 4 DIMMER PAUSE
(MODE)
TOP MENU
/RETURN
DISPLAY AUX/TV 19 a (STOP) – DVD STOP 7C-85 – – STOP 7F01-1DE2 STOP 7A-03
X1 20 PROGRAM (FREQ/TXT) – PROGRAM 7C-A0 FREQ/TXT 78-81 – – –
T1
11 XIN P0B0 20 5 13
SCAN
21
TV INPUT
29
SET UP
37
TV VOL -
45
TAPE/MD
3
21 TV INPUT – TV INPUT : 50-09
4MHz
12 GND P0A3 19 4
2
12
0
20
PROGRAM
28
MENU
36
TV VOL +
44
BAND
22 d (PAUSE (MODE)) – PAUSE 7C-83 MODE 78-82 – PAUSE 7F01-1AE5 –
(FREQ/
D2 TXT)
23 SHUFFLE (START) – SHUFFLE 7C-A1 START 78-83 – SHUFFLE 7F01-46B9 –
13 RESETUP P0A2 18 3 11 19 27 35 43 51
1 9 STOP
ON
SCREEN
(INFO.)
ENTER TUNER AUDIO 24 t (SKIP - (MEMORY)) – SKIP - 7C-B9 – – SKIP/SEARCH - 7F01-1BE4 REW 7A-01
14 17 2 10 18 26 34 42 50 25 w (PLAY) – DVD PLAY 7C-82 – – PLAY 7F01-1EE1 PLAY 7A-00
P1A0 P0A1 TV POWER 8 TV CH -
SKIP +
DVD/CD ZOOM
C3
(SRCH
MODE)
(A-E/CAT.>)
26 y (SKIP + (SRCH MODE)) – SKIP + 7C-BA – – SKIP/SEARCH + 7F01-1CE3 FF 7A-02
15 P1A1 P0A0 16 1 9 17 25 33 41 49 27 ON SCREEN (INFO.) – ON SCREEN 7C-A6 – – INFO. 7F01-15EA –
0.1 µF STANDBY
/ON
7 A-B PLAY
(A-E/CAT.<)
VOLUME - ANGLE
28 MENU – MENU 7C-B2 – – MENU 7F01-0FF0 –

29 SET UP – SET-UP 7C-AC – – – –
4 30 TOP MENU/RETURN – RETURN 7C-B1 – – – –
: Not Mounted T2 31 h (PRESET +) – UP 7C-B4 PRESET/CH B 78-8E – UP 7F01-0EF1 – 7A-07
32 g (PRESET -) – DOWN 7C-B3 PRESET/CH N 78-8F – DOWN 7F01-14EB DIR B 7A-40
33 q (A-E/CAT. <) – LEFT 7C-B5 A-E < 78-9F – LEFT 7F01-10EF REC/PAUSE 7A-04
34 w (A-E/CAT. >) – RIGHT 7C-B6 A-E > 78-9E – RIGHT 7F01-12ED DECK A/B 7A-06
• PANELS • KEY LAYOUT 35 ENTER – ENTER 7C-B8 – – ENTER 7F01-11EE –
36 TV VOL + – TV VOLUME + : 50-12
U, C, T, K, A, L, V models B, G models 37 TV VOL - – TV VOLUME - : 50-15
38 DISPLAY 78-4E <– <– <– <– <– <– <– <– <– <–
39 SLEEP 78-4F <– <– <– <– <– <– <– <– <– <–
40 VOLUME + 78-1E <– <– <– <– <– <– <– <– <– <–
1 2 41 VOLUME - 78-1F <– <– <– <– <– <– <– <– <– <–
42 DVD/CD 78-4A <– <– <– <– <– <– <– <– <– <–
5 3 4 5 6
43 TUNER 78-4B <– <– <– <– <– <– <– <– <– <–
7 8 9 10 44 BAND – – BAND 78-B6 – – –
45 TAPE/MD 78-41 <– <– <– <– <– <– <– <– <– <–
11 12 13 14
46 AUX/TV 78-49 <– <– <– <– <– <– <– <– <– <–
15 16 17 47 DOCK (iPOD) 78-D0 <– <– <– <– <– <– <– <– <– <–
48 SUBTITLE – SUBTITLE 7C-AA – – – –
18 19 20
49 ANGLE – ANGLE 7C-AE – – – –
21 22 23 50 ZOOM – ZOOM 7C-D7 – – – –
51 AUDIO – AUDIO 7C-AD – – – –
24 25 26
27 28
31
6 33 35 34
29 30
32
36 38 40
37 41
39
42 43 44
45 46 47
48 49 50 51
7
49
A B C D E F G H I J
RX-E810/RX-E410/NX-E800
1
■ REMOTE CONTROL WH256400: RX-E410 (B, G models)
• SCHEMATIC DIAGRAM • PANEL • KEY LAYOUT • KEY CODE
Key CUSTOM DATA

J1 Key Label
No. CODE CODE
J2 1
: Not Mounted J8 1 STANDBY/ON 78 0F
J4 J5 J6 J3 3 4 5 6 3 1 78 11
J7
7 8 9 10 4 2 78 12
2 D3
11 12 14 5 3 78 13
15 17 6 4 78 14
41 42 43 44 45 46 47 D2
(VOLUME)
-
CD TUNER BAND TAPE/MD AUX/TV DOCK
18 19 20 7 5 78 15
34 36 37 38 39 40 21 22 23 8 6 78 16
FOLDER/
PRESET (INPUT) DISPLAY (VOLUME) (INPUT) SLEEP
+
9 7 78 17
R1 24
28
2 ohms (1/4W) FOLDER/
PRESET
29
MENU
30
FILE/A-E
31
ENTER
32
FILE/A-E 29 10 8 78 18
D1 28 11 9 78 19
17 18 19 20 21 22 23 24
C1 + MIE-554A2 SKIP/ SKIP/
REPEAT PAUSE STOP RANDOM SEARCH- PLAY SEARCH+ TIME/INFO
30 31 32 12 0 78 10
47µF R2 9 10 11 12 14 15 14 DIMMER 78 BA
27 ohms
7 8 9 0 DIMMER PROG
34
Q1 15 PROG 78 0B
3 2SC3440-T112 1 3 4 5 6 7 8
STANDBY
/ON
1 2 3 4 5 6
38 37 38 17 REPEAT 78 0C
39 41 18 d (PAUSE) 78 B9
40
20 19 18 17 16 15 14 13 12 11 19 a (STOP) 78 01
VDD CARR D0 D1 D2 D3 D4 D5 D6 D7 42 43 44 20 RANDOM 78 07
45 46 47 21 SKIP/SEARCH - 78 04
M34283G2GP-W5/U1 22 w (PLAY) 78 02
IC1 (Z-N0102-84149#1X) 23 SKIP/SEARCH + 78 03
Pb-Free
24 TIME/INFO 78 0A
Vss E2 E1 XIN XOUT E0 G0 G1 G2 G3 28 FOLDER/PRESET h 78 8E
3.0 V
C2
4 1 2 3 4 5
T1
6 7 8 9 10 29 MENU 78 9D
X1
30 FILE/A-E q 78 9F
31 ENTER 78 C1
4MHz 32 FILE/A-E w 78 9E
34 FOLDER/PRESET g 78 8F
36 INPUT h 78 5E
37 DISPLAY 78 4E
38 VOLUME + 78 1E
39 INPUT g 78 40
40 SLEEP 78 4F
5
41 VOLUME - 78 1F
42 CD 78 4A
43 TUNER 78 4B
44 BAND 78 B6
45 TAPE/MD 78 41
46 AUX/TV 78 49
47 DOCK 78 D0
50
RX-E810/RX-E410/NX-E800
■ SYSTEM CONTROL
1. External Bus
1.1. Physical format of external bus
It is composed of 2 bus lines.
MCR-E810 MCR-E410
RX command line RX command line

RX unit DVD unit RX unit CD unit
(RX-E810) (DVD-E810) (RX-E410) (CDX-E410)

State info. line State info. line
1.2. Format of RX command

RX command is the request of RX to DVD or CD unit and the operation button code for CD.
Both are expressed by the remote control code of the NEC format. And the signal wave form is the demodulated
signal of remote control IR signal.
1.3. Format of state info.

State info. is the state information of CD or DVD and expressed by the DC voltage level.
Name DC voltage level Content

PORT_PLAY H The period between from playback operation to stop factor generation.
Playback operation: “PLAY” key operation, disc tray hand push close
Stop factor: “STOP”, “EJECT”, “STANDBY/ON” key operation
Playback contents end
Failsafe stop by abnormal detection
PORT_STOP H x 2/3 Power on state other than PORT_PLAY state
PORT_PRE_STANDBY H x 1/3 The period between from standby operation to standby process
completion and from CD/DVD reset start to initialize process completion
PORT_STANDBY 0 Standby state after standby process completion
H: Microprocessor Vcc level
RX-E810/RX-E410/
RX-E810/RX-E410/
NX-E800
NX-E800
51
RX-E810/RX-E410/NX-E800
Example:
Process Initialize Power on Eject Loading Stop Seek Play Pause Play Skip Play Search Play
H x 2/3
H x 1/3
Reset start "STANDBY/ON" "EJECT" Load "PLAY" "PAUSE" "PLAY" "SKIP" "SEARCH" "PLAY"
key key key key key key key key
Process Play Stop Seek Play Eject Loading Stop Seek Play Stop Seek Play Standby
H x 2/3
H x 1/3
"STOP" "PLAY" "EJECT" Load "PLAY" Contents "PLAY" "STANDBY/ON" Standby process
key key key key end key key complete
Note: The details or some limitations regarding the change of player status need the extra discussion.
RX-E810/RX-E410/
NX-E800
52
RX-E810/RX-E410/NX-E800
2. Command and Operation Key Code

The system command and the system remote control code described as follows are transmitted through RX command
bus.
2.1 RX request command
Name Code Function

to DVD to CD
POWER_ON 7C-F6 78-7E Power on request
POWER_OFF 7C-F7 78-7F Standby request
PLAY 7C-82 78-02 Playback request
STOP 7C-85 78-01 playback stop request
DIMMER_ON 78-FE 78-FE Display dimmer(decrement of brightness) request
DIMMER_OFF 78-FF 78-FF Cancel display dimmer.
VFD_OFF 78-FD 78-FD VFD turn off request
RX request command is not transmitted if DVD/CD is already in the state that RX requests.
2.2 Operation key code (DVD/CD unit)

Key codes which are described at previous "REMOTE CONTROL, • KEY CODE" page are transmitted from RX
unit to DVD/CD unit when user operate the system remote control unit.
RX-E810/RX-E410/
NX-E800
53
RX-E810/RX-E410/NX-E800
3. Command Communication for System Function

3.1 Power on
(1) Power on by RX “STANDBY/ON” key operation
RX turns on the power by RX’s “STANDBY/ON” key and at the same time DVD/CD also turns on the power
if DVD/CD state is power on at the last RX’s power on.
RX unit DVD/CD unit
[Standby state] [Power shut down]

RX "STANDBY/ON" key
operation
Power on process
Power supply through AC OUTLET Reset start

initialize process
PORT_PRE_STANDBY
PORT_STANDBY
Initialize complete
POWER_ON command if necessary *

Power on process
PORT_STOP
* RX transmits POWER_ON command if DVD/CD state at the last RX' s power on is power on.
(2) Power on of individual unit by each “STANDBY/ON” key operation

In the system power on, the each unit can be changed into standby and then into power on again by the
“STANDBY/ON” key operation of the unit.
When the power supply of the unit is individually supplied, only the unit can turn on the power by operating
“STANDBY/ON” key of an individual unit even in system standby.
RX unit DVD/CD unit
[Standby state]
DVD/CD "STANDBY/
ON" key operation
Power on process
PORT_STOP
RX-E810/RX-E410/
NX-E800
54
RX-E810/RX-E410/NX-E800
3.2 Timer function

The unit setted in this RX timer function is playbacked at the setting time as the ON-TIME.
It functions even when at setted time the system is already in power on state or the unit is already playbacked.
(1) Timer play
The state is not changed if the setted unit is already in the state of playback.
RX unit DVD/CD unit
[Standby state]
Wait "ON" setting
time [Power shut down] [Standby state] [Power on] [Play state]
Power on process
Power supply through AC OUTLET Reset start

initialize process
PORT_PRE_STANDBY
PORT_STANDBY
Initialize complete
Switch input function to unit
setted in timer function
POWER_ON command [DVD/CD state is

neither PORT_PLAY nor PORT_STOP]
Power on process
PORT_STOP
PLAY command [DVD/CD state isn' t
PORT_PLAY]
Play process
PORT_PLAY
After sending POWER_ON command, if DVD/CD unit has Auto-play function after power-on, RX will not send
PLAY command.
RX-E810/RX-E410/
NX-E800
55
RX-E810/RX-E410/NX-E800
3.3 Standby (power off)

(1) System standby
The power supply through AC outlet of RX is shut down in system standby (power off).
The microcomputer of the unit connected with AC outlet of RX cannot work after system power off.
When there is processing that should be finished before the system power off, the system is turned power off
after such processing completion.
RX unit DVD/CD unit
[Power on state] [Power on state]

RX "STANDBY/ON"
key operation
POWER_OFF command
PORT_PRE_STANDBY Standby process
Standby process
Standby process complete

PORT_STANDBY
Shut down power supply
through AC outlet
Transition process to
standby state
(2) Unit standby (power off)

Each unit can be individually standby (power off) with an individual “STANDBY/ON” key of each unit.
RX unit DVD/CD unit
[Power on state]
DVD/CD "STANDBY/ON"
key operation

PORT_STANDBY
RX-E810/RX-E410/
NX-E800
56
RX-E810/RX-E410/NX-E800
(3) Auto standby (power off)

When 30 minutes pass with the following conditions consisted, the system turns off the power (standby)
automatically.
a. The unit connected with an external bus is in the standby state.
b. RX input function is DVD/CD.
c. RX is not operated
DVD/CD might turn off the power by own auto standby function.
RX unit DVD/CD unit
[Power on state]
DVD/CD "STANDBY/ON"
key operation [The condition of auto standby
for DVD/CD ownself consisted.]
[30 min with DVD/CD=PORT_PLAY → PORT_STOP,
INPUT=DVD/CD, no operation for RX]
POWER_OFF command

PORT_STANDBY
Standby process
Shut down power supply

through AC outlet
RX-E810/RX-E410/
NX-E800
57
RX-E810/RX-E410/NX-E800
3.4 Display control

(1) Display dimmer function
This is the function to change the brightness of DVD/CD’s display by operating RX.
RX unit DVD/CD unit
Display dimmer on operation

DIMMER_ON command
Display dimmer on
Display dimmer on
Display dimmer off operation

DIMMER_OFF command
Display dimmer off

Display dimmer off
(2) Turn off VFD

This is the function to turn off VFD.
RX unit DVD/CD unit
VFD off operation

VFD_OFF command
Turn off VFD

Turn off VFD
Exit: RX sends DIMMER_ON or DIMMER_OFF command, and then DVD/CD unit turn on VFD with the
appropriate dimmer value.
RX-E810/RX-E410/
NX-E800
58

Yamaha RX-E810, RX-E410, NX-E800 Micro Combo

Uploaded by

Copyright:

Yamaha RX-E810, RX-E410, NX-E800 Micro Combo

Uploaded by

Document Information

Copyright

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Yamaha RX-E810, RX-E410, NX-E800 Micro Combo

Uploaded by

Copyright:

MICRO COMPONENT SYSTEM MCR-E810/MCR-E410

RX-E810/RX-E410/ NX-E800 SERVICE MANUAL

SELF DIAGNOSIS FUNCTION (DIAG) . . . . . . . . . 9–15 SYSTEM CONTROL . . . . . . . . . . . . . . . . . . . . . . 51–58

101019 2006 All rights reserved.

■ TO SERVICE PERSONNEL AC LEAKAGE

WARNING: CHEMICAL CONTENT NOTICE!

About Lead Free Solder

MCR-E810 (U, C, T, K, A, B, G, L, V models) MCR-E410 (B, G models)

■ FRONT PANELS ■ REAR PANELS

RX-E410 (B, G models) RX-E810 (T model)

NX-E800 (U, C, T, K, A, B, G, L, V models) RX-E810 (K model)

RX-E810 (B model) RX-E410 (B model)

RX-E810 (G model) RX-E410 (G model)

■ REMOTE CONTROL PANELS

• When checking the P.C.B.:

Rear panel Ground lead MAIN (1) P.C.B.

Front panel unit 1 CB200

CB201 Front panel unit

■ SELF DIAGNOSIS FUNCTION (DIAG)

No. MAIN MENU SUB MENU

Keys of main unit

Turn on the power while pressing these keys.

• Starting DIAG in the protection cancel mode

• Display provided when DIAG started

When there is no history of protection function:

Opening message DIAG menu display

When there is no protection history After a few seconds

NO PROTECT B VER.B16 4BG

When there is a history of protection function:

History of protection function

• Operation procedure of DIAG menu and SUB-MENU

DIAG menu selection

Keys of main unit

Reverse Forward Reverse Forward

• Functions in DIAG mode

• Initial settings used to start DIAG

• Input DVD (RX-E810 model), CD (RX-E410 model)

* Numeric values in the figure example are for reference.

Firmware version of microprocessor

Checksum value of microprocessor

Checking FL display section

All segments OFF

All segments OFF

All segments ON (dimmer 100%)

All segments ON (dimmer 100%)

All segments ON (dimmer 50%)

All segments ON (dimmer 50%)

Lighting of segments in lattice

Lighting of segments in lattice

PRESET INHIBIT (Initialization inhibited)

PRESET RESERVED (Initialization reserved)

* Numeric values in the figure example are for reference.

P1/P2 (Power supply voltage protection detection)

P3/TH (Power supply voltage protection detection/Temperature detection)

(Normal value: 0 to 176) U, C, T, K, A, B, G models

(Normal value: 0 to 170) L, V models

SYSTEM STATUS 5. iPod

Check item Judgment Display

PANEL KEY (K0/K1) PWR (iPod accessory power)

K0:494 K1:496 PWR:LO DET:HI

6. PROTECTION HISTORY 9. TURN OFF THE POWER FACTOR HISTORY

6-4 No PRT 9-1 NO HISTORY

7. PROTECTION HISTORY RESET

HISTORY RESET Remote control key