Eng CS 82181 Softshell Standard Density 0508 PDF

Soft Shell
Pin and Socket Connectors AMP
5.0 mm Power Key Connectors (5.0 PKC) (Wire-to-Board)
Product Facts
■ Compact design with
19.4 mm mated height
■ Power circuit connector with
5.0 mm contact centerline
■ Wire-to-board connectors
consisting of plug housings
for wires and PCB header
assemblies
■ With a clear clicking sound,
contact insertions can be
made easier. The double
lock plate provides for
complete loading of contacts
■ Locking levers are
surrounded by walls, which
protect levers and prevent
tangling with wires
■ Connector is designed to
release bubbles created
Standard Density
by the process of potting
(PC board coating) 5.0 mm Power Key Performance Characteristics Technical Documents
■ Housing lances also help Connectors are for power Voltage Rating—300 VAC1 Product Specification
prevent tangling of wired circuits of home appliances, Current Rating—10A max.2 108-5699
contacts especially targeting gas
Operating Temperature— Application Specification
■ Recognized under the appliances. The connector -30°C ~ +105˚C 114-5292
Component Program features four kinds of keying
Applicable Wire—24-16 AWG
of Underwriters per housing.
R Applicable PC Board Thickness—
Laboratories Inc., Only color-coding of hous- 1.6 mm
File No. E28476 ings limited the efficiency
.197 [5.00] Centerline

5.0 mm Power Key Connectors
■ Certified by Canadian of blind mating where you
R
could not see connectors. 1 Excludes header tyne round
Standards Association, space. Usable for 150 VAC
File No. LR7189 However, the new keying applications when the round
mechanism not only dimensions are 3 mm or less.
improves assembly 2 Specified values vary according to
efficiency but also helps the number of contacts and the
prevent mismating. wire used. The 10 A maximum
value applies to 16 AWG wire
Part numbers involved used with 2 contacts.
can be reduced so that
purchasing and stock
level control can be
made simpler.
135
Catalog 82181 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 4-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
Soft Shell
5.0 mm Power Key Connectors (5.0 PKC) (Wire-to-Board) (Continued)
Quick Reference Chart for Mating Part Numbers

Plug Housing Applicable
Mating Header Assy.
No. of Pos. Double Lock Plate
Type of Keying/Color Part Number Part Number
Part Number
Type A/Natural 1376388-1 1376394-1 1376382-1
Type B/Red 1-1376388-2 1376394-1 1-1376382-2
2
Type C/Blue 2-1376388-3 1376294-1 2-1376382-3
Type D/Yellow 3-1376388-4 1376394-1 3-1376382-4
Type A/Natural 1376389-1 1376395-1 1376383-1 1376421-1
Type B/Red 1-1376389-2 1376395-1 1-1376383-2 1-1376421-2
3
Type C/Blue 2-1376389-3 1376395-1 2-1376383-3 2-1376421-3
Type D/Yellow 3-1376389-4 1376395-1 3-1376383-4 3-1376421-4
Type A/Natural 1376390-1 1376396-1 1376384-1
Type B/Red 1-1376390-2 1376396-1 1-1376384-2
4
Type C/Blue 2-1376390-3 1376396-1 2-1376384-3
Type D/Yellow 3-1376390-4 1376396-1 3-1376384-4
Type A/Natural 1376391-1 1376397-1 1376385-1
Type B/Red 1-1376391-2 1376397-1 1-1376385-2
6
Type C/Blue 2-1376391-3 1376397-1 2-1376385-3
Type D/Yellow 3-1376391-4 1376397-1 3-1376385-4
2 Row
Type A/Natural 1376392-1 1376394-1 1376386-1
Standard Density
Type B/Red 1-1376392-2 1376394-1 1-1376386-2

4
Type C/Blue 2-1376392-3 1376394-1 2-1376386-3
Type D/Yellow 3-1376392-4 1376394-1 3-1376386-4
Type A/Natural 1376393-1 1376395-1 1376387-1
Type B/Red 1-1376393-2 1376395-1 1-1376387-2
6
Type C/Blue 2-1376393-3 1376395-1 2-1376387-3
Type D/Yellow 3-1376393-4 1376395-1 3-1376387-4
*Included in Header Assy. line are Tube Stick version. Refer to the appropriate description in the catalog.
Note: All part numbers are RoHS Compliant.
Note: Dimensions shown are metric.
136
Soft Shell
Receptacle Contacts
Material and Finish

Pre-tinned Copper Alloy
Section X-X
Wire Range Receptacle Contact Applicator

Wire Ins. Dia. Part No. Part No.
AWG mm2
24~20 0.22~0.53 1.89~2.7 1376348-1 (Strip Form) *
20~16 0.5~1.25 2.0~3.1 1376347-1 (Strip Form) *
Standard Density
* Contact the Tooling Assistance Center (TAC) at 1-800-722-1111 for Applicator Part Number.
Double Lock Plates

Material and Finish
UL94V-0, 6/6 Nylon, glass filled, Black
Dimensions (Double Lock Plate) Double Lock Plate Applicable

No. of Pos. Part No. Plug Part No.
A B
2 13.5 5 1376394-1 첸-1376388-첸 첸-1376392-첸
3 18.5 10 1376395-1 첸-1376389-첸 첸-1376393-첸
4 23.5 15 1376396-1 첸-1376390-첸
6 33.5 25 1376397-1 첸-1376391-첸
* Contact the Tooling Assistance Center (TAC) for Applicator Part Number.
137
Soft Shell
Plug Housings
(For Receptacle Contacts)
Material and Finish

Housing—6/6 Nylon, glass filled
Related Product Data

Receptacle Contacts—page 137
Double Lock Plates—page 137
Mating Headers—page 140
Section X-X
Standard Density
Type of Keying/Color
Plug Housing Part No. Applicable

Dimensions Type of Keying/Color Double Mating
No. of Header Assy.
Pos. Type A Type B Type C Type D Lock Plate
A B Part Number Part Number
Natural Red Blue Yellow
2 15 — 1376388-1 1-1376388-2 2-1376388-3 3-1376388-4 1376394-1 첸-1376382-첸
첸-1376383-첸
3 20 10 1376389-1 1-1376389-2 2-1376389-3 3-1376389-4 1376395-1 첸-1376421-첸
4 25 15 1376390-1 1-1376390-2 2-1376390-3 3-1376390-4 1376396-1 첸-1376384-첸
6 35 25 1376391-1 1-1376391-2 2-1376391-3 3-1376391-4 1376397-1 첸-1376385-첸

138
Soft Shell
Plug Housing (2 Rows)

(For Receptacle Contacts)
Material and Finish


Receptacle Contacts—page 137
Double Lock Plates—page 137
Mating Headers—page 141
Section X-X
Standard Density

Plug Housing Part No.
Applicable
No. of Dimensions Type of Keying/Color Double Mating
Pos. Lock Plate Header Assy.
Type A Type B Type C Type D Part Number
A B Part Number
4 15 — 1376392-1 1-1376392-2 2-1376392-3 3-1376392-4 1376394-1 씲-1376386-씲
6 20 10 1376393-1 1-1376393-2 2-1376393-3 3-1376393-4 1376395-1 씲-1376387-씲

139
Soft Shell
Vertical Header Assembly
Material and Finish

Tab Contacts -Copper Alloy, Tin plated

Mating Plug Housings—page 138
Section X-X
Standard Density
PC Board Layout
Vertical Header Assy. Part No.

Dimensions Loose Piece Mating
No. of Type of Keying/Color
Pos. Tube Plug Housing
A B Type A Type B Type C Type D Part Number
(Qty.)
L.P 1376382-1 1-1376382-2 2-1376382-3 3-1376382-4
2 11.6 — 씲-1376388-씲
Tube 1376437-1 (40) 1-1376437-2 (40) 2-1376437-3 (40) 3-1376437-4 (40)
L.P 1376383-1 1-1376383-2 2-1376383-3 3-1376383-4
3 16.6 10 씲-1376389-씲
Tube 1376439-1 (25) 1-1376439-2 (25) 2-1376439-3 (25) 3-1376439-4 (25)
L.P 1376384-1 1-1376384-2 2-1376384-3 3-1376384-4
4 21.6 15 씲-1376390-씲
Tube 1376440-1 (20) 1-1376440-2 (20) 2-1376440-3 (20) 3-1376440-4 (20)
L.P 1376385-1 1-1376385-2 2-1376385-3 3-1376385-4
6 31.6 25 씲-1376391-씲
Tube 1376441-1 (15) 1-1376441-2 (15) 2-1376441-3 (15) 3-1376441-4 (15)
L.P 1376421-1 1-1376421-2 2-1376421-3 3-1376421-4
2* 16.6 10 씲-1376389-씲
Tube 1376444-1 (25) 1-1376444-2 (25) 2-1376444-3 (25) 3-1376444-4 (25)
*10 mm centerline
140
Soft Shell
Vertical Header Assembly

(2 Rows)
Material and Finish

Tab Contacts—Copper Alloy, Tin
plated

Mating Plug Housings—page 139
Section X-X
Standard Density

PC Board Layout
Vertical Header Assy. Part No.

Dimensions Loose Piece Mating
No. of Type of Keying/Color
Tube Plug Housing
Pos. A B Type A Type B Type C Type D Part Number
(Qty.)
L.P 1376386-1 1-1376386-2 2-1376386-3 3-1376386-4
4 11.6 — 씲-1376392-씲
Tube 1376442-1 (40) 1-1376442-2 (40) 2-1376442-3 (40) 3-1376442-4 (40)
L.P 1376387-1 1-1376387-2 2-1376387-3 3-1376387-4
6 16.6 10 씲-1376393-씲
Tube 1376443-1 (25) 1-1376443-2 (25) 2-1376443-3 (25) 3-1376443-4 (25)

141
Soft Shell
Engineering Notes
142
Soft Shell
.093 [2.36] Commercial Pin and Socket Connectors
Product Facts
■ Polarized
■ Cavity identification
■ Low contact-mating force
■ Dual locking lances
■ Detent and positive locking
■ Contacts available in brass
and phosphor bronze with
tin and gold plating
■ Panel mounting and free-
hanging styles
■ “F” crimp contacts
■ Applicator and hand tool
available
■ Economical commercial-
grade connectors
■ Compatible with high-speed
application machinery and
competitive soft shells
■ Wire range 24 to 14 AWG
[0.2 to 2 mm2]
Accepts wires with
Standard Density
■
insulation diameters as
large as .180 [4.57]
■ Housings available in 1 to
15 positions
■ .093 plug and receptacle Performance Characteristics Technical Documents
housings accept pin or The .093 Commercial Pin and Socket Application Specification
socket contacts. The Connectors performance characteristics 114-49000 .093 Commercial Pin and
preferred convention is to found on pages 143-144 are based on Socket Connectors
use socket contacts with free-hanging and panel mount connec- Product Specification

receptacle housings tors, loaded with contacts crimped on 108-1038 .093 Commercial Pin and
stranded wire. Socket Connectors
■ Not for interrupting current
Thermal Shock— -55°C to +105°C
■ Recognized under the
Component Program of Temperature-Humidity Cycling—
Underwriters +25°C to +65°C at 90–95% RH
Laboratories Inc., Corrosion—48 hr. at 5% salt
File No. E28476 R
concentration
■ Certified by Canadian Vibration—10-55-10 cycles per
Standards Association, minute at .06 [1.52] total excursion
File No. LR 7189 R Physical Shock—18 shocks,
50 Gs sawtooth in 11 milliseconds
Durability—50 mating cycles
Dielectric Withstanding Voltage—
1.0 kVAC
Insulation Resistance—
1000 megohms min. initial
Voltage Rating—250 V AC or DC
Connector Mating—
2.5 lb. [11.1 N] max. per contact
Connector Unmating—
1.5 lb. [6.7 N] min. per contact
Contact Retention—
10 lb. [44.5 N] min.
143
Soft Shell
.093 [2.36] Commercial Pin and Socket Connectors (Continued)

Performance Current Rating Verification for 30°C Maximum Temperature Rise 100% Energized
Characteristics (continued)
Wire-to-Wire
Maximum Current—Maximum cur-
rent rating of .093 Commercial Pin and .093 Commercial Pin and Socket Connectors — Calculated Current Table
Socket Connectors is limited by the Number of Wire AWG
maximum operating temperature of the Circuits 14 16 18 20 22 24
housings which is 105°C including the 2 13.00 12.00 11.00 8.00 6.00 6.00
temperature rise of the contacts which 3 13.00 11.00 10.00 8.00 6.00 5.00
is a maximum of 30°C. There are 4 In-Line 11.00 10.00 9.00 7.00 5.00 4.00
several variables which have a direct 4 Matrix 11.00 10.00 9.00 7.00 5.00 4.00
effect on this maximum current-carrying
5 10.00 9.00 8.00 6.00 5.00 4.00
capability for a given connector and
must be considered for each application. 6 10.00 9.00 8.00 6.00 4.00 4.00
These variables are: 9 9.00 7.00 6.00 5.00 4.00 3.00
12 8.00 7.00 6.00 4.00 3.00 3.00
Wire Size—Larger diameter wire will
15 7.00 6.00 5.00 4.00 3.00 3.00
carry more current since it has less
internal resistance to current flow and Values are based on initial Temperature Rise versus Current Testing and are intended to be a guide in the selection
thus generates less heat. Longer wire of a connector family. All applications should be tested by the end user. The values listed are per circuit for fully
lengths also enhance current-carrying loaded housings being 100% energized. Note: All combinations were not tested and this chart contains interpolated
capabilities since the wire conducts and extrapolated values.
heat away from the connector.
Connector Size—In general, the more
circuits in a connector, the less current
can be carried.
Ambient Temperature—The higher Minimum Wire Lengths for T-Rise vs. Current Testing
the ambient temperature, the less current AWG Min. Length (in.) AWG Min. Length (in.)
Standard Density
can be carried in any given connector. 30 2.6 18 9.4

28 3.2 16 11.3
Related Product Data 26 4.1 14 13.7
24 5.1 12 16.4
Product Specification — 108-1038
20 7.8 10 19.3
Note: If wire lengths used are less than those listed above, the current-
carrying ability of the system will be reduced due to less heat being
conducted away from the connector. The customer should fully test
all applications.
Termination Resistance/Contact Crimp Tensile Force

Contact
Termination
Wire Size Crimp
Resistance Tensile Force
Test Resistance Force (Min.)
AWG mm2 Current Milliohms
(Amps) (Max. Init.) lbs. N
24 0.2 2.0 4.0 8 35.6
22 0.3–0.4 3.0 4.0 10 44.5
20 0.5–0.6 4.5 4.0 15 66.7
18 0.8–0.9 6.0 3.5 25 111.2
16 1.25–1.4 8.0 3.5 25 111.2
14 2 10.0 3.0 30 133.4
Note: This is the total resistance between wire crimps of a mated pin and
socket.
144
Soft Shell
Contacts
Pin Diameter .093 [2.36]
Material .780
[19.81]
.780
[19.81]
.010 [0.25] Stock Thickness
Pin and socket contacts can be used in
either plug or receptacle housings.
Related Product Data Pin Socket

Product Specification — 108-1038
Application Specification
114-49000
Performance Characteristics—
pages 143-144 .973 .973
[24.71] [24.71]
Housings
.198 [5.03] Centerline—pages 146-147
.250 [6.35] Centerline—pages 148-149
Panel Cutouts
.198 [5.03] Centerline Housings—
page 147
.250 [6.35] Centerline Housings— Pin Socket
page 148 Part No. 770385-1 Part No. 770383-1
Technical Documents—pages 143
Standard Density
and 205-206
Application Tooling—pages 207-210
Contact Part Numbers HDM
Wire Size Material Applicator Hand Tool
Ins. Dia. & Finish Pin Socket Part Part No.
AWG mm2
Strip Form Loose Piece Strip Form Loose Piece No.
Brass, 350418-1 770147-1 350417-1 770146-1
Pre-tin
466656-15
.110 Brass,
24–18 0.2–0.9 — — 350417-32 770146-32 466656-25 90872-1
2.79 Gold2
466656-35
Brass 350418-51 770147-51 350417-51 770146-51
Select Gold1

Brass, 350416-1 770145-1 350415-1 770144-1
Pre-tin
466878-15
.140 Brass,
350416-51 770145-51 350415-51 770144-51 466878-25 90871-1
3.56 Select Gold1
20–14 0.6–2 466878-35
Phos. Brz., — — 350415-6 770144-6
Pre-tin
Contact Insertion Tool 567337-36
.180 Brass, 770530-14 — 770529-14 — 567337-46 —
(For Pins and Sockets) 4.57 Pre-tin 567337-66
Part No. 91002-1
IS 408-7347 18–14 0.8–2 .180 Brass, 770385-13 — — — 567273-27
or or 4.57 Pre-tin
567273-37 —
2 2 (per Phos. Brz.,
(18) (0.8–0.9) wire) — — 770383-13 — 567273-47
Pre-tin
1Select Gold — .000030 [.000762] min gold in mating area over .000050 [.00127] min nickel.
2Gold — .000030 [.000762] min gold in mating area, overall gold flash over .000050 [.00127] min nickel.
3These contacts have a .0125 [.318] stock thickness and accept two wires, each with maximum .180 [4.57] insulation
diameters. They can be used only with the following housing part numbers: 770364-1, 770365-1, 770450-1,
770451-1, 770452-1, and 770453-1 (see page 143).
4Contact length is .875 [22. 23]
5HDM Applicator part number ending in -1 is used on AMPOMATOR CLS Machine with T or G Terminators, -2 is
used on AMP-O-LECTRIC Model K Machine, -3 is used on AMP-O-LECTRIC Model G Machine. See pages 207-210
for further information.
used on AMP-O-LECTRIC Model K Machine, -6 is used on AMP-O-LECTRIC Model G Machine. See pages 207-210
Contact Extraction Tool for further information.
Part No. 318837-1 7HDM Applicator part number ending in -3 is used on AMPOMATOR CLS Machine with T or G Terminators, -2 is
IS 408-4375 used on AMP-O-LECTRIC Model K Machine, -4 is used on AMP-O-LECTRIC Model G Machine. See pages 207-210
for further information.
Note: Phosphor bronze contacts should be used in high-temperature/humidity cycling applications.
145
Soft Shell
Housings 1 Circuit
Free-Hanging or Panel Mount .360
[9.14]
.198 [5.03] Centerline spacing
Material
Housing —Nylon, natural color
Flammability Rating— .240
[6.10] .245
UL94-V-2 1.000 [6.22] .970
[25.40]
[24.64]
Related Product Data Receptacle Plug

Contacts —page 145
Product Specification —108-1038
2, 3, and 4 Circuit, In-Line
Panel-Mount Flange
.198
[5.03] Typ.
A A
198 Typ.
5.03]
Standard Density
.340
[8.64] 1.095
[27.81]
.240
[6.10]
1.125
[28.58]
Receptacle Plug
Receptacle Part Numbers

Plug Part Numbers

No. of A Dimension Panel Mount Free-Hanging
Circuits Panel Free-
Receptacle Plug Without With Without With Mount Hanging
Detents Detents Detents Detents
1 — — — — — 770063-1 — 770064-1
2 .540 .640 — 770066-11,5 — 770065-11,5 770068-11 770069-11
13.72 16.26 7702661,3,5
3 .670 .770 — 770071-1 — 770070-1 770073-1 770074-1
17.02 19.56 770264-13
4 .870 .970 — 770076-1 — 770075-1 770077-1 770078-1
(In-Line) 22.10 24.64
4 .443 .540 — — — 770843-1 — 770842-1
(Matrix) 11.25 13.71
5 1.070 1.170 — — — 770083-1 — 770084-1
27.18 29.72 794015-13
6 1.268 1.378 — — — 770782-14 — 770892-14
(In-Line) 32.21 35.00
6 .435 .535 770085-1 770087-1 770088-1 770086-1 770089-1 770090-1
(Matrix) 11.05 13.59
9 .670 .770 770091-1 770093-1 770094-1 770095-12 770096-1
17.02 19.56 770092-1 770108-1
12 .870 .970 770097-1 770099-1 770100-1 770098-1 770101-1 770102-1
22.10 24.64
15 1.070 1.170 770103-1 — 770105-1 — 770106-1 770107-1
27.18 29.72
1.248 [6.30] centerline.
2Mounting ears at wire end.
3Tool removable.
4Positive lock.
5600 V AC or DC
146
Soft Shell
Housings 5 Circuit, In-Line

Free-Hanging or Panel Mount
Material
Housing —Nylon, natural color .198
1.070
.198
1.170
[5.03] [5.03]
Flammability Rating — Typ. [27.18] Typ. [29.72]
UL94V-2

Contacts —page 145
.240 1.125
Product Specification —108-1038 [6.10] [28.58] .340 1.095
[8.64] [27.81]
Receptacle (Free-Hanging) Plug (Free-Hanging)
4, 6, 9, 12, and 15 Circuit, Matrix
.198
.198 [5.03]
[5.03]
Standard Density
.198 .198
[5.03] [5.03]
.430 .535 ± .010

[10.92] [13.59 ± 0.25]
.630 1.000 ± .010

.735 ± .010
[16.0] [25.4 ± 0.25]
[18.67 ± 0.25] .970 ± .010

[24.64 ± 0.25]
Receptacle Plug
A
Recommended Panel Cutout Dimensions
No. of
Panel Cutouts Circuits
Receptacle Plug
Maximum panel thickness is A B A B
.090 [2.29]. 2 .312 .725 .375 .800
7.92 18.42 9.53 20.32
3 .312 .840 .375 .933
7.92 21.34 9.53 23.70
B 4 .312 1.038 .375 1.131
(In-Line) 7.92 26.37 9.53 28.73
6 .600 .718 .695 .750
15.24 18.24 17.65 19.05
9 .725 .828 .660 .937
18.42 21.03 16.76 23.80
12 .725 1.050 .760 1.155
18.42 26.67 19.30 29.34
15 .655 1.240 .760 1.343
16.64 31.50 19.30 34.11
Note: The panel should be punched so that the housing enters in the same
direction as the punch.
147
Soft Shell
Housings 3 Circuit, In-Line

Panel-Mount
Panel-Mount .250
.250 [6.35] Centerline spacing Flange [6.35]
Flange
.250
Material .765 [6.35] Typ. .862
[19.43] [21.89]
Flammability Rating —
UL94V-2
Voltage Rating—600 V AC or DC
.255 1.140
[6.48] Max. [28.96] .350 1.100
Related Product Data [8.89] [27.94]
Contacts —page 145 Receptacle Plug
Product Specification —108-1038

4 Circuit, In-Line
Panel-Mount
Panel-Mount .250
250 Typ. Flange
6.35] Flange [6.35] Typ.
1.005 1.112
[25.53] [28.24]
Standard Density
.255 1.140
[6.48] .350 1.100
[28.97] [8.89] Max. [27.94]
Receptacle Plug
6 Circuit, Matrix
.250 1.105
545 1.145 [28.07]
3.84] [6.35]
[29.08]
Max.
.250
[6.35] Typ.
.790 .886
20.07] [22.50]
.250
[6.35] Typ. Panel-Mount
Flange Panel-Mount
Flange
.250 .641
[6.35] [16.28]
Receptacle Plug
Recommended A
No. of
Receptacle Part Numbers Plug Part Numbers
Panel Cutouts Circuits Panel Free- Panel Free-
Mount Hanging Mount Hanging
Maximum panel thickness is 770269-1
.062 [1.57]. 3 770771-11 770339-1 770338-1 770276-1
Note: The panel should be punched 4 770329-1 770337-1 770330-1 770336-1

so that the housing enters in the same 6 770372-1 770360-1 770373-1 770361-1
direction as the punch. 1Pre-bent mounting ears.
B
Panel Cutout Dimensions

No. of
Receptacle Plug
Circuits
A B A B
3 .310 .920 .365 1.022
7.87 23.37 9.27 25.96
4 .310 1.168 .365 1.270
7.87 29.67 9.27 32.26
6 .608 .946 .658 1.048
15.44 24.03 16.71 26.62

148
Soft Shell
Housings Dual Wire

.555
Free-Hanging or Panel Mount 2 Circuit, In-Line [14.10]
.250 [6.35] Centerline spacing .248 .248

[6.30] [6.30]
.545 .650
Material [13.84] [16.51]
Flammability Rating — .445
UL94V-2 [11.30] 1.245
[31.62] 1.250
Voltage Rating —600 V AC or DC [31.57]
Receptacle Plug
Contacts —page 145 3 Circuit, In-Line
Product Specification —108-1038 .350
.255 [8.89]
[6.48] Max.
Panel-Mount
Panel-Mount Flange
.250 .250
[6.35] Typ. Flange [6.35]
.765 .862
[19.43] [21.89]
.500 1.315 .500 1.275
Standard Density
[12.70] [33.40] [12.70] [32.39]
Receptacle Plug
Receptacle Part Numbers Plug Part Numbers

No. of
Circuits Panel Free- Panel Free-
Mount Hanging Mount Hanging
2 — 770364-11 — 770365-11
3 770453-12 770451-1 770452-12 770450-1

2See panel cutout dimensions on page 58.
Positive Lock
2, 3 and 4 Circuit, In-Line
.248 .248
[6.30] [6.30]
.536 .666
[13.61] [16.92]
.255 1.073
[6.48] [27.25]
1.041
[26.44]
Receptacle Plug
No. of Receptacle Part Numbers Plug Part Numbers

Circuits Free-Hanging Free-Hanging
2 770424-11 770425-11
3 770785-1 770783-1
4 770784-1 770810-1
149
Soft Shell
Engineering Notes
150
Soft Shell
Commercial MATE-N-LOK Connectors
Product Facts
■ Fully polarized nylon
housings
■ Easy cavity identification
■ Locking devices are integral
part of design. Connector
halves will hold together
under severe conditions of
vibration and shock
■ Built-in contact stabilization
and self-aligning features
■ Hot side egg-crate design
for safety
■ Precision molded to exact-
ing tolerances
■ Contacts accept a wire
size range of 30-14 AWG
[.05-2.0 mm2]
■ Keying plug available
■ “Clean” design contact —
no sharp projections to
impede insertion or damage
housings
■ Low insertion/extraction
Standard Density
forces
■ Contacts available in pre-tin Performance Characteristics Technical Documents
or gold over nickel plated to
fit the application require- The Commercial MATE-N-LOK Product Specifications
Connector performance characteristics 108-1000 Commercial MATE-N-LOK
ments found on pages 151-152 are based on Connectors
■ Wire-to-PC Board capability free-hanging and panel mount connec-
108-1077 Commercial MATE-N-LOK
using pin or socket headers tors, loaded with contacts crimped on
PC Board Headers
stranded wire.
■ Solderability—Headers meet 108-49000 IDC Connectors
MIL-STD 202 method 208 1.5 KVAC between adjacent circuits Application Specifications

■ Four circuit PC Board-to-PC Insulation Resistance— 114-1012 Commercial MATE-N-LOK
Board capability available 500 megohms minimum initial between Contacts
by mating vertical socket adjacent circuits 114-49001 IDC Connectors
header with either vertical, Voltage Rating—250 V AC or DC Instruction Sheets
right-angle or surface mount Connector Mating— 408-7209, 408-7166, 408-7200,
pin header 4 lb. max. per circuit 408-7201, 408-7215, 408-3186,
■ Four circuit insulation dis- Connector Unmating— 408-7300
placement connector (IDC) 0.7 lb. min. per circuit
available Contact Retention—15 lb. min.
■ Ultraviolet (UV) stable per contact
housings available in 1, 2 Durability—50 cycles, mating and
and 3 circuit unmating
Component
Program of R
Underwriters Laboratories
Inc., File No. E28476
■ Certified by
Canadian Standards
Association,
R
File No. LR 7189A
151
Soft Shell
Commercial MATE-N-LOK Connectors (Continued)
Characteristics (Continued)
Wire-to-Wire
rent rating of Commercial MATE-N-LOK Motor Mount Calculated Current Table
connectors is limited by the maximum Number of Wire Gauge
operating temperature of the housings Circuits 14 16 18 20 22 24 30
which is 105°C including the tempera-
6 13.00 10.50 9.50 7.50 6.00 5.00 2.50
ture rise of the contacts which is a
maximum of 30°C. There are several 8 12.00 9.50 8.50 7.00 5.50 4.50 2.50
variables which have a direct effect on 10 11.00 9.00 8.00 6.50 5.00 4.50 2.00
this maximum current-carrying capabil- 12 10.50 8.50 7.50 6.00 5.00 4.00 2.00
ity for a given connector and must 16 9.50 8.00 7.00 5.50 4.50 3.50 2.00
be considered for each application.
Values are based on initial Temperature Rise versus Current Testing and are intended to be a guide in the selection of a con-
These variables are: nector family. All applications should be tested by the end user. The values listed are per circuit for fully loaded housings
Wire Size—Larger diameter wire will being 100% energized. Note: All combinations were not tested, and this chart contains interpolated and extrapolated values.
internal resistance to current flow and Calculated Current Table
thus generates less heat. Longer wire Wire Gauge
Number of
lengths also enhance current-carrying Circuits 14 16 18 20 22 24 30
capabilities since the wire conducts heat
away from the connector. 1 19.00 15.50 14.00 11.00 9.00 7.50 4.00
2 18.00 14.50 13.00 10.50 8.50 7.00 4.00
3 16.00 13.00 12.00 9.50 7.50 6.50 3.50
can be carried. 4 15.00 12.50 11.00 9.00 7.00 6.00 3.00
6 Matrix 13.00 10.50 9.50 7.50 6.00 5.00 3.00
Ambient Temperature—The higher
8 12.50 10.50 9.00 7.50 6.00 5.00 2.50
the ambient temperature, the less current
9 11.00 9.00 8.00 6.50 5.50 4.50 2.50
can be carried in any given connector.
10 12.00 9.50 8.50 7.00 5.50 4.50 2.50
Printed Wiring Board Conductor 12 10.50 8.50 7.50 6.00 5.00 4.00 2.00
Size—The finished trace conductor
Standard Density
15 9.50 8.00 7.00 5.50 4.50 4.00 2.00

width and thickness should be maxi-
mized to allow for the greatest current- Values are based on initial Temperature Rise versus Current Testing and are intended to be a guide in the selection of a con-
carrying capacity and heat dissipation. nector family. All applications should be tested by the end user. The values listed are per circuit for fully loaded housings
being 100% energized. Note: All combinations were not tested, and this chart contains interpolated and extrapolated values.
Wire-to-Board Minimum Wire Lengths for T-Rise vs. Current Testing

Commercial MATE-N-LOK connectors
Due to the vast differences in trace AWG Min. Length (in.) AWG Min. Length (in.)
also will withstand the following tests: geometry and printed circuit board 30 2.6 18 9.4
Vibration—10-55-10 cycles per configurations, we are unable to
provide a separate current carrying 28 3.2 16 11.3
minute at .06 inch total excursion
chart for our printed circuit board 26 4.1 14 13.7
Physical Shock—18 drops,
header products. However, the 24 5.1 12 16.4

50 G sawtooth at 11 milliseconds above Wire-to-Wire charts may be 20 7.8 10 19.3
used as a guideline for headers if
Housing Panel Mount Retention— the trace width and thickness is Note: If wire lengths used are less than those listed above, the current carry-
40 lb. min. 3 and 4 circuit equal to the listed wire gauge. For ing ability of the system will be reduced due to less heat being conducted
65 lb. min. 6, 9, 12, and 15 circuit vertical headers, only 95% of the away from the connector. The customer should fully test all applications.
Wire-to-Wire value should be used.
Housing Lock Strength with For right-angle headers, only 75% of
Positive Locking Devices the Wire-to-Wire value should be
Engaged— used. The chart values are only a
25 lb. min. tool for connector selection and will
require the customer to fully test
Thermal Shock— -55°C to +85°C their application.
Termination Contact
Temperature-Humidity Cycling— Resistance Crimp
Wire Size Tensile Force
25°C to 65°C at 95 RH Test Resistance
AWG mm2 Current Milliohms Force (Min.)
Corrosion—48 hr. at 5% salt (Amps) (Max. Init.) lbs. N
concentration
30 .05 .50 4.00 2 9
28 .08 .75 3.50 3 13
26 .12 1.00 3.50 7 31
24 .2 1.5 3.50 10 44
22 .3 3 3.50 15 67
Product Specifications 20 .5 4.5 3.00 20 89
108-1000 Commercial MATE-N-LOK 18 .8 6 3.00 30 133
Connectors 16 1.2 8 2.75 30 133
108-1077 Commercial MATE-N-LOK 14 2.0 10 2.75 35 156
PC Board Headers
Note: This is the total resistance between wire crimps of a mated pin and socket.
152
Soft Shell
Commercial MATE-N-LOK Connector Mating Combinations

Connector Part Number Mating Connector Part Number
PC Board Headers
Number Vertical Vertical
of Flammability Style Housing Connector Housing Housing Pin Right-Angle Socket
Circuits Rating Type Part No. Part No. Type Plating Standard Long Pin Standard Long
Tail Tail Tail Tail
1-480350-0 Pin: FH — — — — — —
Socket: FH 1-480349-0 Pin: FH
1-480351-0 — — — — — —
1 UL94V-2 In-Line Positive Lock
Socket: FH Pin: FH
UV Stable 1-480400-0 1-480401-1 UV Stable — — — — — —
Pre-tin 350209-1 350422-1 794120-1 — —
Socket: FH 1-480318-0 1-480319-0 Pin: FH
Duplex1 1586512-2 — — — —
Socket: FH Pin: FH
2 UL94V-2 In-Line 1-480393-1 1-480498-1 — — — — — —
UV Stable UV Stable
Socket: FH Pin: FH Pre-tin 350539-1 350540-1 — — —
Positive Lock 1-480720-0 794012-1 Positive Lock
Duplex1 1586530-2 — — — —
Pre-tin 350210-1 350423-1 643488-1 — —
Socket: FH 1-480303-0
1-480305-0 Pin: FH Duplex1 1586514-2 — — — —
Socket: PM 1-480304-0 — — — — — —
3 UL94V-2 In-Line Socket: FH Pre-tin 350541-1 350542-1 — — —
Positive Lock 1-480721-0 — —
Duplex1 1586532-2 — — — —
Socket: FH Pin: FH
UV Stable 1-480388-0 1-480387-0 UV Stable — — — — — —
4 See next page for 4 position mating combinations
Pin: FH
1-480340-0 Positive Lock Pre-tin 1-380999-0 350425-1 — — —
Socket: FH
Positive Lock 1-480270-0
Pin: MM
1-480271-0 Duplex 1 2-1586546-0 1586526-2 — — —
Positive Lock
Standard Density
6 UL94V-2 Matrix Socket: PM Pin: PM Pre-tin — — — — —
Positive Lock 1-480273-0 1-480276-0 Positive Lock
Duplex1 — — — — —
Pin: PM Socket: PM Pre-tin — — — 350641-1 350576-1
Positive Lock 1-480276-0 1-480273-0 Positive Lock
Duplex1 — — — — —
Pin: FH
1-480345-0 Positive Lock Pre-tin 350212-1 350426-1 — — —
Dual Socket: FH
8 UL94V-2 Row Positive Lock 1-480283-0
Pin: MM
1-480284-0 Duplex1 1586518-2 1586528-2 — — —
Positive Lock
9 UL94V-2 Matrix Positive Lock 1-480277-0 1-480274-0 Positive Lock
Duplex1 — — — — —
Pin: FH

1-480339-0 Positive Lock Pre-tin 1-380991-0 350219-1 — — —
Dual Socket: FH
10 UL94V-2 Row Positive Lock 1-480285-0
Pin: MM
1-480286-0 Duplex 1 2-1586544-0 — — — —
Positive Lock
Dual Socket: MM Pin: MM Pre-tin 350213-1 350220-1 — — —
Row Positive Lock 1-480287-0 1-480288-0 Positive Lock
Duplex1 1586520-2 1586524-2 — — —
12 UL94V-2
Matrix Positive Lock 1-480278-0 1-480275-0 Positive Lock
Duplex1 — — — — —
15 UL94V-2 Matrix Positive Lock 1-480324-0 1-480323-0 Positive Lock
Duplex1 — — — — —
Dual Socket: MM Pin: MM Pre-tin 350214-1 350427-1 — — —
16 UL94V-2 Row Positive Lock 1-480438-0 1-480439-0 Positive Lock
Duplex1 1586522-2 1586529-2 — — —
FH: Free-Hanging PM: Panel Mount MM: Motor Mount
1Duplex Finish — Plated with .000030 [.000762] min. gold in mating area, matte tin on solder tail end over .000050 [.00127] min. nickel underplate on entire contact.
153
.200 [5.08] Centerline Standard Density
154
Revised 4-08
Catalog 82181
www.tycoelectronics.com
Commercial MATE-N-LOK 4 Position In-Line Mating Combinations (Note: These connectors are used by the disk drive industry.)
Socket Connectors PC Board Pin Headers
Flammability Connector Connector Housing Housing PC Board Vertical Right-Angle
Plating Insulation
Rating Type Part No. Part No. Type Vertical Surface
Displacement AWG Standard Long Standard W/Fixed W/Fixed Belt
Socket Mount
Connector Header Tail Tail Belt Reverse Pol.
Socket Pre-tin — — — 350543-1 350544-1 — — — —
Housing 1-480772-0 — —
are metric equivalents.

Positive Lock Duplex1 — — — 1586534-2 1586536-2 — — — —
Soft Shell
specified. Values in brackets

Socket 350211-1 641737-1
millimeters unless otherwise

Dimensions are in inches and
Housing Pre-tin — — — 350424-1 770829-1 174804-1 174552-1
1-480424-0 1-480426-0 Pin 770328-13 770846-1
Detent
Lock
Duplex1 — — — 1586515-2 1586525-2 — — — —
770156-2 22
1-480424-0 Socket
Pin 770156-3 18 770997-1
to change.
Housing Pre-tin 794287-12 — — — — — —
1-480426-0 770156-4 20
Pin and Socket Connectors
Detent Socket
Lock 1-480425-0 770156-5 16
UL94V-2 PM
Duplex1 770526-1 18 — — — — — — —
Specifications subject
Pin Housing Socket
reference purposes only.

Detent Lock 3-480426-0 3-480425-0 High — — — — — — — — — —
Dimensions are shown for

High Temp Temp
Socket 770997-1 641737-1

1-480426-0 Pin Pre-tin — — — 350211-1 350424-1 770829-1 174804-1 174552-1
Header 794287-12 770846-1
770156-2
Insulation 770156-3 641737-1 174804-1
Displacement Pre-tin — — — 350211-1 350424-1 770829-1 174552-1
770156-4 1-480426-0 Pin 770846-1
Connector 770156-5
(IDC)
770526-1 Duplex1 — — — 1586515-2 1586525-2 — — — —
USA: 1-800-522-6752
Socket 770827-1 794132-1 Pin Pre-tin — — — — — — 1-641737-1 — —
Canada: 1-905-470-4425
Housing
Mexico: 01-800-733-8926
Insulation 794036-1
C. America: 52-55-1106-0803
Displacement 794036-2 794132-1 — Pre-tin — — — — — — 1-641737-1 — —
Connector 794036-3
UL94V-0 (IDC) 794036-4
794036-1 18
Right-Angle 794036-2 20
Pin Header 1-641737-1 770827-1 Socket Pre-tin — 794236-1 — — — — —
794036-3 22
794036-4 16
PM: Panel Mount
1Duplex Finish — Plated with .000030 [.000762] min. gold in matting area, matte tin on solder tail end over .000050 [.00127] min. nickel underplate on entire contact.
UK: 44-8706-080-208
Japan: 81-44-844-8013
2Surface Mount Compatible.
3With Drainholes
Hong Kong: 852-2735-1628

South America: 55-11-2103-6000

AMP
Soft Shell
Contacts
Pin diameter .084 [2.13]
Stock thickness .012 [.305]
These contacts are to be used in
Commercial MATE-N-LOK housings
only.

Product Specification .805 .695
108-1000 Commercial MATE-N-LOK [20.44] [17.65]
Connectors
Contacts Pin Socket
pages 151-152
Housings—pages 157-159
and 205-206
Wire Size Contact Part Numbers HDM

Ins. Dia. Hand Tool
Range Material & Finish Pin Socket Applicator
Range Part No.
AWG [mm2] Strip Form Loose Piece Strip Form Loose Piece Part No.
Brass, Pre-tin 350079-1 61174-1 350078-1 61173-1 466426-13
30-22 .040-.075 Phos. Brz., Pre-tin 350079-4 — 350078-4 61173-4 466426-23 91515-1
Standard Density
[.05-.3] 1.02-1.91 466426-33
Brass, Gold1 350079-5 61174-5 350078-5 61173-5
Brass, Pre-tin 61116-1 60618-1 61314-1 60617-1
Phos. Brz., Pre-tin 61116-4 60618-4 61314-4 60617-4 466320-13
24-18 .060-.100 91512-1
Brass, Gold1 61116-5 60618-5 61314-5 60617-5 466320-23
[.2-.8] 1.52-2.54 466320-43 91528-14
Phos. Brz., Select Gold2 61116-6 60618-6 61314-6 60617-6
Brass, Select Gold2 61116-7 — 61314-7 —
Brass, Pre-tin 61118-1 60620-1 61117-1 60619-1
Phos. Brz., Pre-tin 61118-4 60620-4 61117-4 60619-4 687763-13
20-14 .100-.130 Brass, Gold1 61118-5 60620-5 61117-5 60619-5 687763-23 91504-1
[.5-2.0] 2.54-3.30 687763-63
Phos. Brz., Gold1 61118-6 — 61117-6 60619-7

Brass, Select Gold2 61118-7 — 61117-7 —
(2) 18 [.8] or (2) .115 Max. Brass, Pre-tin 350558-1 350639-1 350557-1 — 687898-13
(1) 18 [.8] and 2.92 687898-23 91504-1
(1) 16 [1.2] (stacked) Phos. Brz., Pre-tin 350558-4 — 350557-4 350638-4 687898-43
1Gold Finish — Plated with .000030 [.000762] min. gold in mating area and inside wire barrel over .000050 [.00127] min. nickel underplate on entire contact.
2Select Gold Finish — Plated with .000030 [.000762] min. gold in mating area over .000050 [.00127] min. nickel underplate on entire contact.
3HDM Applicator part number ending in -1 is used on AMPOMATOR CLS Machine with T or G Terminators, -2 is used on AMP-O-LECTRIC Model K
Machine; -3, -4, or -6 is used on AMP-O-LECTRIC Model G Machine. See pages 207-210 for further information.
4Use Hand Tool No. 91528-1 for .043-.075 [1.09-1.90] insulation diameter.
Notes:
1. Extraction Tools: Pins — No. 1-305183-1 (IS 408-7158); Sockets — No. 1-305183-2 (IS 408-7158); Pins and Sockets — No. 465644-1 (IS 408-7211)
2. Insertion Tools: No. 455830-1 (IS 408-7984)
Commoning Tabs .170 Number of Dimensions Part

[4.32] Holes Number
A B
.377 .203
Material and Finish A 2 9.58 5.16 60843-1
Brass, tin plated .355 .195

2 9.02 4.95 350444-1
Stock thickness .008 [.203] B .579 .203
3 14.71 5.16 60842-1
.550 .195
.008 3 13.97 4.95 350444-2
[.203]
Note: Commoning tabs are designed to be used with pin housings.
155
Soft Shell
Contacts PC Board Contacts

Stock thickness .012 [.305] L L
These contacts are to be used in

Commercial MATE-N-LOK housings
only.

Product Specification
108-1000 Commercial MATE-N-LOK Pin Socket
Connectors
Part Numbers
Application Specification L Dim.
Type of Contact Material & Finish Pin Socket
114-1012 Commercial MATE-N-LOK Pin Socket
Loose Piece Loose Piece
Contacts
1.110 1.010
Performance Characteristics— [28.19] [25.65] Phos. Brz., Pre-tin 61518-11 61320-11
pages 151-152 PC Board
1.210 1.110 Phos. Brz., Pre-tin 350074-12 350073-12
Housings—pages 157-159 [30.73] [28.19]
1For .062 [1.57] max. board thickness — Board hole size .057 [1.45]
and 205-206 2For .125 [3.14] max. board thickness — Board hole size .057 [1.45]
Grounding Pin .900

[22.86]
(.095 [2.41] longer than standard pin)
(Mate first, break last, not for interrupting
current)
Standard Density
Contact Part Numbers HDM

Wire Size Range Ins. Dia. Hand Tool
Material & Finish Applicator
AWG [mm2] Range Strip Form Loose Piece Part No.
Part No.
466320-11
24-18 .060-.100 Brass, Pre-tin 61527-2 — 466320-21 91512-1
[.2-.8] 1.52-2.54 466320-41
used on AMP-O-LECTRIC Model K Machine; -3, -4, or -6 is used on AMP-O-LECTRIC Model G Machine. See
pages 207-210 for further information.
Keying Plug 1.000

[2.54]
IS 408-7582
Material
Housing — Nylon, natural color Part Number
200821-1
Flammability Rating — UL94V-2 Note: Keying plug snaps into socket housing
156
Soft Shell
Housings 1 Circuit
Free-Hanging
Material B A E D
Housing —Nylon, natural color Pin Housing (Cap) Detent Lock Socket Housing (Plug)
Flammability Rating —UL94V-2

B A
Connectors Pin Housing (Cap) Positive Lock
pages 151-152
Contacts—pages 155-156
Commoning Tabs—page 155 2, 3 and 4 Circuit,
Keying Plug—page 156 In-Line
C B E
and 205-206 F
Mating Pin Headers—pages 161-164 .200
[5.08]
Mating Socket Headers—page 162
Mating IDC—page 163
A
D
Pin Housing (Cap)
Standard Density
Socket Housing (Plug)
Number of Dimensions Part Numbers

Circuits A B C D E F Pin Housing (Cap) Socket Housing (Plug)
.300 1.200 .260 .870
7.62 30.48 — 6.60 22.10 — 1-480350-01 1-480349-0
.300 1.240 .260 .870
1 7.62 31.49 — 6.60 22.10 — 1-480351-02 1-480349-0
.300 1.325 .260 .995
7.62 33.65 — 6.60 25.27 — 1-480401-01,3 1-480400-03
.610 .930 .330 .530 .860 .295

15.49 23.62 8.38 13.46 21.84 7.49 1-480319-01,5 1-480318-05
2
.610 .930 .330 .530 .860 .295 1-480498-11,3,5 1-480393-13,5
15.49 23.62 8.38 13.46 21.84 7.49
.810 .930 .325 .825 .850 .290
20.57 23.62 8.25 20.95 21.60 7.37 1-480305-01,5 1-480303-05
3
.810 .930 .325 .825 .850 .290 1-480387-01,3,5 1-480388-03,5
20.57 23.62 8.25 20.95 21.60 7.37
1.010 .930 .330 1.030 .850 .310
25.65 23.62 8.38 26.16 21.60 7.88 1-480426-01,5,6 1-480424-05,6
4
1.030 .850 .310
— — — 26.16 21.60 7.88 794132-14,5,6 770827-14,5,6
1Detentlock
2Positive
lock
3UV Stable black color
4Housing Material UL94V-0 rated
5Housing accepts double wire applications where individual insulation diameters do not exceed .115 [2.92].
6Used by the disk drive industry.
157
Soft Shell
Housings 2, 3, and 4 Circuit, .375 .850

[21.59]
[9.52]
Free-Hanging, Positive Lock In-Line
A
Material
.200
Housing —Nylon, natural color [5.08]
Flammability Rating —UL94V-2 .150

[3.81]
Socket Housing (Plug)
Part Numbers
Number of A
Circuits Dim. Socket Housing Mates with Mates with
(Plug) Pin Headers Cap Housing
.435
2 11.04 1-480720-0 350539, 350540 794012-1
.630
3 16.00 1-480721-0 350541 —
.830
4 21.09 1-480722-01 3505431, 3505441 —

6 Circuit, Dual Row
.785 .930 .850 .725

[19.94] [23.62] [21.59] [18.41]
.195
[4.95]
A D
Standard Density
.360
[9.14]
Pin Housing (Cap) Socket Housing (Plug)
8 and 10 Circuit, Dual Row

.785 .930 .850 .725

[19.94] [23.62] [21.60] [18.42]
.195
[4.95]
A
D
.360
[9.14]
Product Specification Pin Housing (Cap) Socket Housing (Plug)

Connectors Number of Dimensions Part Numbers
Performance Characteristics— Circuits A D Pin Housing (Cap) Socket Housing (Plug)
pages 151-152 .705 .610
Contacts—pages 155-156 6 17.91 15.49 1-480340-0 1-480270-01
Commoning Tabs—page 155 .900 .805
8 1-480345-0 1-480283-01
Keying Plug—page 156 22.86 20.44
Technical Documents—pages 151 10 1.095 1.000 1-480339-0 1-480285-01
and 205-206 27.81 25.40
Mating Headers—pages 161-164 1Housing accepts double wire applications where individual insulation diameters do not exceed .115 [2.92].
158
Soft Shell
Housings 3 and 4 Circuit, In-Line

Panel Mount, Positive Lock E .930 .850 .310
[23.62] [21.59] [7.87]
.200
[5.08]
Material
F G
Flammability Rating —UL94V-2

Product Specification Pin Housing (Cap) Socket Housing (Plug)
Connectors 6, 9, 12 and 15 Circuit,
Performance Characteristics— Matrix
pages 151-152 .850 .850 .650
.930
Contacts—pages 155-156 [21.59] [23.62] [21.59] [16.51]
Commoning Tabs—page 155 .240
Keying Plug—page 156 [6.09]
and 205-206
Mating IDC—page 163 F G
Recommended Panel
Cutout for Panel Mount .202
Socket Housing [5.130]
View is from socket housing entry
Standard Density
side
Number of Dimensions Part Numbers
Mounting Information
Circuits E F G Pin Housing (Cap) Socket Housing (Plug)
1. Recommended panel thickness—
.025-.065 [.635-1.65]. .325 .810 .630
3 8.26 20.57 16.00 1-480305-02 1-480304-0
2. Both locking legs are to be
squeezed together and the hous- .330 1.010 .825 1-480426-02,4 1-480425-04
4 8.38 25.65 20.96 3-480426-01,2,4 3-480425-01,4
ing is to be inserted “straight-in”,
as opposed to a rocking manner. .665 .555
6 — 1-480276-03 1-480273-0
3. The panel should be punched so 16.89 14.10
that the housing enters the panel .905 .795
9 — 22.99 20.19 1-480277-03 1-480274-0
in the same direction as the
punch. 1.145 1.045

4. The panel must not have any 12 — 29.08 26.54 1-480278-03 1-480275-0
material (paint, porcelain, etc.) 1.382 1.280
applied in the mounting hole area 15 — 35.10 32.51 1-480324-03 1-480323-0
that would decrease the retention
1Housing material has 125°C temperature rating
of the housing in the panel.
2Detent lock
5. If the two items above are not
3Positive lock
complied with, the “A” dimension
4Used by disk drive industry
should be reduced .020 [5.08] for
proper retention. Note: All part numbers are RoHS Compliant.
6, 9, 12 and 15 Circuit,
3 and 4 Circuit, In-Line
Matrix
.275 .219
Number Dimensions
[6.98] .660 [5.56]
.215 Circuits A B
[5.46] [16.76]
C .890 .645–.635
C 3 22.61 16.38–16.13
.218 1.100 .845–.835
[5.54] 4 27.94 21.46–21.21
A
B
.840 .575–.570
6 21.34 14.61–14.48
A 1.075 .815–.810
9 27.31 20.70–20.57
.015 B
R Max. D 1.320 1.055–1.050
[.381] 12
All Corners 33.53 26.80–26.67
1.550 1.290–1.285
15 39.37 32.77–32.64
.015
R Max.
D [.381] Note: Dimensions “C” and “D” are to
All Corners be equal.
159
Soft Shell
Motor Mount, Positive Lock 6, 8, 10, 12 and 16 Circuit,

Dual Row
.850 .725
.785 .930 [21.59] [18.41]
[19.94] [23.62]
E F
.195
[4.95]
.360
[9.14]
Part Numbers
Number of Dimensions
Circuits E F
UL94V-2 Nylon, Natural Color
.705 .610
6 17.90 15.49 1-480271-0 1-480270-01
.900 .805
8 22.86 20.45 1-480284-0 1-480283-01
1.095 1.000
10 27.81 25.4 1-480286-0 1-480285-01
Standard Density
1.290 1.195
12 32.77 30.35 1-480288-0 1-480287-0
1.680 1.585
16 42.67 40.26 1-480439-0 1-480438-0
1Housing accepts double wire applications where individual insulation diame-

ters do not exceed .115 [2.92].
Recommended
Panel Cutout for .015
R Max. Number of A
[.381] Circuits Dim.
Motor Mount All Corners
.715
Pin Housing A 6 18.16
E
A .910
View is from pin housing entry 8 23.11
side.
R 1.105
10 28.07
1.300
12 33.02
A
T 1.690
.585 16 42.93
[14.86] Section A-A
Mounting Information
Note: Motor mount housings may be used in 1. Recommended panel thickness
flat panels “E” is .040-.100 [1.02-2.54] and is
dependent on “T” and “R”.
2. The pin housing must be inserted
in a rocking manner.
3. The panel must be punched so
that the housing enters the panel
in the same direction as the
punch.
160
Soft Shell
PC Board Vertical Pin 2, 3, and 4 Circuit,

Headers In-Line .330 .375
[3.38] [9.52]
.330 .375 .070
[8.38] [9.52] [1.78] Dia. Typ.
.200
Material [5.08]
Typ.
Housing — Nylon, natural color A

A
Flammability Rating — UL94V-2
Contacts — Phosphor bronze
Solder tail diameter .062 [1.57] Positive Lock Detent Lock Recommended PC Board Hole Layout
Mounting Dimensions

6, 8, 10, 12 and 16 Circuit,
Product Specifications Dual Row
PC Board Headers .375 .070 Dia. Typ. .195 Typ.
.785
Performance Characteristics— [19.93] [9.14] [1.78] [4.95]
pages 151-152
Technical Documents—pages 151 .360
and 205-206 [9.14]
A
Mating Socket Housings—
pages 157-160
Mating IDC—page 163 Positive Lock Recommended PC Board Hole Layout
Mounting Dimensions
Part Numbers Mates with

Number of A Type
Standard2 Long3 Socket Housing
Circuits Dim. Lock Finish
Tail Tail Part Number
Standard Density
Pre-tin 350539-1 350540-1
Positive 1-480720-0
.515 Duplex1 1586530-2 —
2
13.09 Pre-tin 350209-1 350422-1
Detent 1-480318-0
Duplex1 1586512-2 —
Pre-tin 350541-1 350542-1
Positive 1-480721-0
.715 Duplex1 1586532-2 —
3
18.17 Pre-tin 350210-1 350423-1
Detent 1-480303-0
Duplex1 1586514-2 —
Pre-tin 350543-15 350544-15
Positive 1-480722-05
Duplex1 1586534-25 1586536-25

350211-15
.915 Pre-tin 350424-15
4 23.24 794236-15,8
1-480424-04,5
Detent 1586627-15,6
Post-tin
1-1586627-15,6,7
Duplex1 1586515-25 1586525-25
.705 Pre-tin 1-380999-0 350425-1
6 Positive 1-480270-0
17.91 Duplex1 2-1586546-0 1586526-2
.900 Pre-tin 350212-1 350426-1
8 Positive 1-480283-0
22.86 Duplex1 1586518-2 1586528-2
1.095 Pre-tin 1-380991-0 350219-1
10 Positive 1-480285-0
27.81 Duplex1 2-1586544-0 —
1.290 Pre-tin 350213-1 350220-1
12 Positive 1-480287-0
32.77 Duplex1 1586520-2 1586524-2
1.680 Pre-tin 350214-1 350427-1
16 Positive 1-480438-0
42.68 Duplex1 1586522-2 1586529-2
1Duplex Finish — Plated with .000030 [.000762] min. gold in mating area, matte tin on solder tail end over .000050
[.00127] min. nickel underplate on entire contact.
2Use standard tail for .062 [1.57] thick PC Board.
3Use long tail for .125 [3.18] thick PC Board.
4Other mating connectors include a vertical PC Board socket header and the insulation displacement connectors (IDC).
6With drain holes.
7Tube loaded.
8Housing material UL94V-0 rated.
161
Soft Shell

.375 .375
PC Board Surface Mount 4 Circuit, In-Line [9.53] [9.53] .125
Dia.
Right-Angle Pin Header Housing
.484
.100 .100
[3.18]
[12.30] 2 Plcs.
1.000 [2.54] [2.54]
[25.40] Contact .075 .350
Material and Finish .300 .300
[1.91] [8.89]
4 3 2 1 [7.62] [7.62]
.330
Housing — Nylon, black color [8.38]
Flammability Rating — UL94V-2 .150
Min.
See [3.8]
Contact — Phosphor bronze, pre-tin .153
Note
[3.89] .100
Solder tail width .052 [1.32] .120
.100 [2.54] Typ.
[3.05] Dia.
[2.54]
Part Number
770829-1 Note: .010 [.25] min. thick solder paste,
Notes: 63/27 tin
1. Mating parts include socket housings, a
vertical PC Board socket header below and Recommended PC Board Layout
the insulation displacement connectors (IDC). .062 [1.57] thick PC Board
2. Used by the disk drive industry.
PC Board Vertical 4 Circuit, In-Line .440 .170

Socket Headers .245
[11.18] [4.32]
.015
[6.22] [0.38] .070
Dia. Typ. .200
.200 [1.78] Typ.
[5.08]
Material [5.08]
4
Typ.
Housing — Nylon, natural color
3
A .824
Flammability Rating — UL94V-2 [2093]
2
Contacts—Phosphor bronze Recommended PC Board Hole Layout

1
Solder tail diameter .062 [1.57] .062 [1.57] thick PC Board
6, 9, 12 and 15 Circuit,
Standard Density
Matrix
.070
[1.78] Dia. Typ.
15 14 13
12 11 10 .240
Typ.
[6.09]
A
9 8 7
6 5 4
.202
[5.13]
3 2 1
.645 .470 Recommended PC Board Hole Layout

[16.38] [11.94] .062 [1.57] thick PC Board
Part Numbers Mates with

Number of A Finish Pin Housing
Circuits Dim. Standard Tail5 Long Tail6 Part Number
770997-13 —
Related Product Data 1.000
4 Pre-tin 794285-13,7 — 1-480426-02,3
25.40
Product Specifications 794287-13,4,8 —
108-1077 Commercial MATE-N-LOK .720 Pre-tin 350641-1 350576-1
6 1-480276-0
PC Board Headers 18.29 Duplex1 1586539-2 —
Performance Characteristics— .960
9 Pre-tin 350642-1 350577-1 1-480277-0
pages 151-152 24.39
Technical Documents—pages 151 12 1.200
30.49 Pre-tin 350643-1 350578-1 1-480278-0
and 205-206
Mating Pin Housings—pages 157-160 15 1.440 Pre-tin 350644-1 350579-1 1-480324-0
36.58
Mating Pin Headers—pages 161-164
1Duplex Finish — Plated with .000030 [.000762] min. gold in mating area, matte tin on solder tail end over
Mating Socket Housings—
.000050 [.00127] min. nickel underplate on entire contact.
pages 157-160 2Other mating connectors include vertical, right-angle and surface mount PC Board pin headers.
Mating Socket Headers—page 162 3Used by the disk drive industry.
4Surface mount compatible.
Mating IDC—page 163 5Use standard tail for .062 [1.57] thick PC Board.
6Use long tail for .125 [3.18] thick PC Board.
7Low Mating Force
8High Temperature
162
Soft Shell
PC Board Right-Angle 2, 3, and 4 Circuit, In-Line 2, 3, and 4 Circuit

Pin Headers .484 .345 .300 .157 Dia.
.150 D
[12.29] [.876] [7.62] C [3.98]
[3.81]
.157 .100 (2 Plcs.)
Dia. B
Material and Finish [3.99]
.100
[2.54]
.100 Dia.
2 Plc. .400 [2.54]
Contact — Phosphor bronze, pre-tin A [2.54]
.060 2 Plc. [10.16] (2 Plcs.)
Solder tail width .052 [1.32] [1.52] .100 .060 Dia.
2 Plc. .200 [2.54] .100 .200 [1.524]
[5.08] [2.54] [5.08] (4 Plcs.)
.140 Typ.
[3.55] Typ.
Recommended PC Board Hole Layout
.062 [1.57] thick PC Board
Dimensions Mates with

Number of Part
Housing Material Socket Housing
Circuits A B C D Numbers Part Number
.600 .300 UL94V-2 Nylon
2 15.24 — 7.62 — Natural Color 794120-1 1-480318-0
.800 .150 .300 .600 1-480303-0
3 20.32 3.81 7.62 15.24 UL94V-0 Nylon 643488-1
UL94V-2 Nylon, 641737-13
Natural Color 770846-11,3 1-480424-02,3
1.000 .200 .400 .800
4 25.40 5.08 10.16 20.32
UL94V-0 Nylon 1-641737-13 770827-12,3
1Surface Mount Compatible. 2Other mating connectors include a vertical PC Board socket header and the insulation
displacement connectors (IDC). 3Used by the disk drive industry.
Dust Covers .325 Max.

[8.25]
Material .505 Max. .505

Max.
[12.82] [12.82]
Housing — Polyester, white color
Standard Density
Flammability Rating — UL94V-2 .142 .760
.142 Max. .760 [3.60]
[3.60] [19.30] [19.30]
Max.
For Feed-To Wiring For Feed-Through Wiring
Part Number 770232-1 Part Number 770233-1
Note: These parts are used with the insulation displacement connectors below.
Insulation Displacement
4 Circuit, In-Line
Connectors (IDC)
.830

.994 [21.08]
Material [25.24] Max.
.200
[5.08]
Housing — Nylon
Contact — Phosphor bronze
.643
.390 [16.33]
[9.90] Max.
Socket Assembly (Plug)
Used by the disk drive industry.
Product Specifications
Wire Size Range Color Part Number Mates with
108-1077 Commercial MATE-N-LOK AWG [mm2] Code Finish
UL94V-2 UL94V-0 Part Numbers
PC Board Headers
22 1-480426-0**
108-49000 IDC Connectors [.3] Red Pre-tin 770156-2 794036-3
350211-1
Application Specification 20 350211-2
[.5] Yellow Pre-tin 770156-4 794036-2 350424-1
114-49001 IDC Connectors 18 350424-2
Performance Characteristics— [.8] Orange Pre-tin 770156-3 794036-1 641737-1
1-641737-1
pages 151-152 770827-1
16 770829-1
Technical Documents— [1.2] Blue Pre-tin 770156-5* 794036-4
770846-1
pages 151 and 205-206
Mating Socket Housings— *Application Tooling: Arbor Tool 91085-2 uses head 231920-2. **Pin Housing
pages 157-160 Notes:
1. Insulation diameter .095 [2.41] max.
Mating Pin Housings— pages 157- 2. Application Tooling
160 Power Unit No. 91112-2 (IS 408-7763) uses Head No. 231920-2 (IS 408-9330) and Hand Tool Handle No. 58074-1
Mating Pin Headers— pages 161-164 (IS 408-6790) uses Terminating Head No. 231894-1(IS 408-3186)
163
Soft Shell
PC Board Right-Angle 4 Circuit, In-Line

Pin Header with Fix Belt .996
[25.30] .453
.217 [11.50]
.016
Material [5.50]
[.400]
Ref. .402
[10.20]
Housing — Thermoplastic 1 2 3 4
.346
Flammability Rating — UL94V-2 [8.80]
Contacts — Copper Alloy
.167
[4.23] .161
.150
.200 [4.10]
Related Product Data [5.08] .400 [3.80]
Used by the disk drive industry [10.16]
.600
Product Specification .933 [15.24]
[23.70]
108-5155
.933 .209
Part No. 174552-1 [23.70] [5.30]
Notes: Mates with socket housing Part No. 1-480424-0.
Other mating connectors include a vertical PC Board
socket header and the insulation displacement .091 .215
connectors (IDC). [2.30] [5.45]
.200
.059
[5.08]
[1.50] .400
.167
[10.15] .600 [4.23]
[15.24]

PC Board Right-Angle 4 Circuit, In-Line

Standard Density
Pin Headers with Fix Belt .996

.453
Reverse Polarization .217
[25.30] .016 [11.50]
Ref.
[5.50] [.400]
.402
Ref. [10.20]
Material and Finish .362 .346
.512 [9.20] [8.80]
Housing — Nylon 4 3 2 1
[13.00]
Flammability Rating — UL94V-2 A Ref.*
.167
Contacts — Tin plated, Copper alloy [4.23] .161
.200 [4.10]
[5.08] .400
[10.16]
Related Product Data .600

Used by the disk drive industry .933 [15.24]
[23.70]
108-5155
.933 .209
[23.70] [5.30] Part No. A Dim.* Description
.150 Long Clamp
174804-1 3.80 with Kink
.215
.090 [5.45]
[2.30]
.167
2 Plcs. .059
[4.23]
[1.50] .200
4 Plcs. [5.08]
.400
[10.16]
.600
[15.24]
Part No. 174804*

Notes: Mates with socket housing Part No. 1-480424-0. Other mating connectors include a vertical PC Board socket
header and the insulation displacement connectors (IDC).
164
Soft Shell
.140 MATE-N-LOK Connectors (Large Insulation), .240 Centerline
Product Facts
■ Available in 2, 3 and 9
circuit configurations for
panel mounting; 4 and 9
circuit configurations for
free-hanging applications
■ Standard natural nylon
housings
■ Housings fully polarized
■ Contacts fully protected in
housings
■ Contacts accept wire
size range 20-10 AWG
[.5-5.0 mm2] with insulation
diameters from .100 [2.54]
to .180 [4.57]
■ Low insertion/extraction
forces
■ Dual locking lances provide
optimum contact stability
■ Extraction tool removes both
pins and sockets
■ Contacts are on .240 [6.09]
centerline spacing
Standard Density
Component Program
of Underwriters Maximum Current—Maximum cur- Termination Contact
Laboratories Inc., R
rent rating of .140 MATE-N-LOK Resistance Crimp

File No. E28476 Wire Size Tensile Force
Connectors is limited by the maximum Test Resistance
AWG mm2 Force (Min.)
■ Certified by Canadian operating temperature of the housings Current Milliohms
which is 105°C and the temperature rise (Amps) (Max. Init.) lbs. N
Standards Association, R
of the contacts which is 30°C. There are 20 .5 4.5 3.0 20 89

File No. LR 7189A several variables which have a direct 18 .8 6 2.5 30 133
effect on this maximum current-carrying 16 1.2 8 2.5 45 200
capability for a given connector and
Performance Characteristics 14 2.0 10 2.0 50 222
must be considered for each application.

.140 MATE-N-LOK Connectors (Large Insulation)
12 3.0 12 1.5 60 267
The .140 MATE-N-LOK Connector per- These variables are:
formance characteristics found on this 10 5.0 14 1.5 65 289
page are based on free-hanging and Note: This is the total resistance between wire crimps of a mated pin and socket.
carry more current since it has less inter-
panel mount connectors, loaded with
nal resistance to current flow and thus Current Rating Verification for 30°C Maximum Temperature Rise
contacts crimped on stranded wire.
generates less heat. Longer wire lengths 100% Energized
Dielectric Withstand Voltage— also enhance current-carrying capabili-
3.0 KVAC between adjacent circuits ties since the wire conducts heat away Wire-to-Wire
Insulation Resistance— from the connector. .140 MATE-N-LOK Connector Calculated Current Table
1000 megohms minimum initial between Connector Size—In general, the more Number of Wire AWG
adjacent circuits circuits in a connector, the less current Circuits 10 12 14 16 18 20
Voltage Rating—600 V AC or DC can be carried. 2 28.00 23.00 18.50 15.00 13.50 10.50
Connector Mating—4.5 lb. max. per Ambient Temperature—The higher 3 25.00 21.00 17.00 13.50 12.00 9.50
circuit the ambient temperature, the less current 9 18.50 15.00 12.00 10.00 9.00 7.00
can be carried in any given connector.
Connector Unmating—.8 lb. min. per Values are based on initial Temperature Rise versus Current Testing and are
circuit intended to be a guide in the selection of a connector family. All applications
Technical Documents should be tested by the end user. The values listed are per circuit for fully
Contact Retention—30 lb. min. loaded housings being 100% energized. Note: All combinations were not
Durability—25 cycles, mating and tested, and this chart contains interpolated and extrapolated values.
108-1032 .140 Diameter
unmating
MATE-N-LOK Connectors Minimum Wire Lengths for T-Rise vs. Current Testing
Thermal Shock— -55°C to +85°C
Application Specification Note: If wire lengths used are less than those listed, the current carrying
Temperature-Humidity Cycling— 114-1007 .140 Diameter ability of the system will be reduced due to less heat being conducted away
25°C to 65°C at 95 RH MATE-N-LOK Contacts from the connector. The customer should fully test all applications.
165
Soft Shell
.140 MATE-N-LOK Connectors (Large Insulation), .240 Centerline (Continued)
Contacts .995 .795

[25.27] [20.19]

108-1032 .140 Diameter Pin Socket
MATE-N-LOK Connectors
Application Specification Contact Part Numbers
Wire Size HDM Hand Tool
114-1007 .140 Diameter Range Ins. Dia. Material & Finish Pin Socket Applicator Part No.
MATE-N-LOK Contacts AWG [mm2] Range Strip Form Loose Piece Strip Form Loose Piece Part No.
Performance Characteristics— Brass. pre-tin 61627-1 350389-1 61626-1 350388-1 567306-1

20-14 .100-.180 567306-2 90247-1
page 159 [.5-2.0] 2.54-4.5 Phos. Brz., pre-tin 61627-2 — 61626-2 — 567306-3
Keying Plug— none
Brass. pre-tin 350201-1 350391-1 350200-1 350390-1 567309-1
Housings— pages 166-167 14-10 .100-.180
[2.0-5.0] 2.54-4.5 Phos. Brz., pre-tin 350201-2 350391-2 567309-2 69710-12
Technical Documents— pages 165 350200-2 350390-2 567309-3
and 205-206 1HDM Applicator part number ending in -1 is used on AMPOMATOR CLS Machine with T or G Terminators, -2 is used
Application Tooling— pages 207-210 on AMP-O-LECTRIC Model K Machine, -3 is used on AMP-O-LECTRIC Model G Machine. See pages 207-210 for
further information.
2Hand Tool No. 69710-1 uses die set No. 58374-1 for 14-12 AWG and No. 58373-1 for 10 AWG.
Housings
Free-Hanging Contact Extraction Tool
.240 [6.09] Centerline spacing Part No. 318845-1
IS 408-4378
Material
Standard Density
Nylon, natural color

4 Circuit
Cavity Identification 1.130 1.065 1.180
[28.70] [27.05] [29.97]
(Rear View)
.565 .580
[14.35] [14.73]
.240 .240 .950

[6.09] [6.09] .775 [24.13]
Cap
.865 [19.68] 1.350

[21.97] [34.29]

Part No. 1-480512-0 Part No. 1-480510-0
Part No. 794700-1 (Black Color High Temp.)
Plug
9 Circuit, Matrix
.755 .950
1.130 .845 [19.17] [24.13]
.240
[28.70] [21.46] [6.09]
Cap .755 .845 .755

[19.17] [21.46] [19.17]
.240
[6.09]

Part No. 1-480586-0 Part No. 1-480585-0
Plug
166
Soft Shell
.140 MATE-N-LOK Connectors (Large Insulation), .240 Centerline (Continued)
Housings 2 and 3 Circuit, In-Line

Panel Mount .240
[6.09]
.515 .815 .965 .515
Material [13.08] [20.70] [24.51] [13.08]
Housing — Nylon, natural color
Flammability Rating — UL94V-2 .275
.950 [6.98] 1.130
Cavity Identification [24.13] .365 [28.70]
(Rear View) [9.27]
Socket Housing (Plug) Pin Housing (Cap)
Part No. 1-350344-0 Part No. 1-350345-0
Part No. 794699-1 (Black Color High Temp.) Part No. 1586305-1 (Black Color High Temp.)
.240
[6.09]
Plug
Cap .755 1.205 .755
1.055
[19.17] [26.79] [19.17]
[26.79]
.950 .275
[6.98] .365 1.130
[24.13]
[9.27] [28.70]

Part No. 1-350346-0 Part No. 1-350347-0
Part No. 794061-1 (Black Color High Temp.)
Plug
9 Circuit, Matrix
Cap
.755 .950 1.130 .910
[19.17]
Standard Density
.240 [24.13] [28.70] [23.11]
[6.09]
.240
[6.09]
.755 .950 .910
[19.17] [24.13] [23.11]
.240 .240
[6.09] [6.09]
Plug

Part No. 1-480672-0 Part No. 1-480673-0
Part No. 1586305-1 (Black Color High Temp.) Part No. 794683-1 (Black Color High Temp.)
Recommended Panel Cutouts

View is from housing entry side
Cap 2 and 3 Circuit 9 Circuit
Notes:
1. Panel thickness .040-.070
Related Product Data [1.02-1.78].
1.025
Product Specification C1 [26.03] 2. "X" and "Y" dimensions must
X .765 Y be within .005 [.127] of each
108-1032 .140 Diameter .0502 [19.43] other.
MATE-N-LOK Connectors [1.27] .475 .190 3. Panel should be punched so
Application Specification [12.06] [4.82] .288 that the housing enters the
X
[7.31] panel in the same direction as
114-1007 .140 Diameter .050 2
the punch for ease of assembly.
MATE-N-LOK Contacts [1.27]
Performance Characteristics— 12 Circuit-.725 [18.42] .765 1.025
page 165 [19.43] [26.03]
3 Circuit- .965 [24.51]
Keying Plug— none 2.050 x .050 [1.27-1.27] tabs in corners of
Contacts— page 166 outlet are optional to reduce housing .190
Technical Documents— pages 165 float in panel. [4.82]
and 205-206
167
Soft Shell
Engineering Notes
168
Soft Shell
Universal MATE-N-LOK Connectors
Product Facts
■ Pins and sockets can be
intermixed in the same
housing
■ Positive polarization
■ Rear cavity identification
■ Contacts completely
enclosed in housings
■ Positive locking housings
■ Insulation capability to .200
[5.08] diameter
■ Removable, crimp snap-in
contacts
■ Low contact mating force
■ Contacts accept 30-10 AWG
[.05-5.0 mm2] wire sizes
■ Contacts available with pre-
tin or gold plating
■ Dual locking lances provide
optimum contact stability
■ Panel mount or free-hanging
■ Mate with Universal
MATE-N-LOK II Housings
■ Available in UL 94V-O flame
retardant material. Meets
the material requirements of Performance Characteristics Technical Documents
table 25.1 of U.L. Standard The Universal MATE-N-LOK Connector Product Specifications
1410 (television receivers performance characteristics found on 108-1031 Universal MATE-N-LOK
Standard Density
and video products) pages 169-170 are based on free-hanging Connectors
and panel mount connectors, loaded
■ Not for interrupting current 108-1053 Universal MATE-N-LOK
with contacts crimped on stranded wire.
PC Board Headers
■ Harness to PC Board capa- Dielectric Withstanding Voltage—
bility using pin or socket 5.0 KVAC or 5.0 KVDC between Application Specification
headers adjacent circuits 114-1010 Universal MATE-N-LOK
Contacts
■ Pin and socket headers are Insulation Resistance—
1000 megohms minimum initial between Instruction Sheet
available in both vertical and
adjacent circuits 408-7714 Plug, Cap, Headers, Pin,
right-angle style
Voltage Rating—600 V AC or DC Socket and Accessories

■ Solderability — headers meet
Contact Insertion Force—
MIL-STD 202 Method 208 5.0 lb. max. per contact
■ Contacts are on .250 [6.35] Contact Retention—15 lb. min.
centerline spacing per contact
■ Recognized under the Durability—50 cycles, mating and
Component unmating
Program of R
■ Certified by Canadian R
Standards Association,
File No. LR 7189
■ Passed test by VDE under
their Registration Number
3980/Continuous
Surveillance
169
Soft Shell
Universal MATE-N-LOK Connectors (Continued)
Wire-to-Wire
rent rating of Universal MATE-N-LOK Calculated Current Table
operating temperature of the housings Circuits 10 12 14 16 18 20 22 24 26 30
which is 125°C for 94V-2 housings and 2 19.00 18.00 17.00 14.50 13.00 10.00 8.00 6.50 5.50 3.50
120°C for 94V-0 housings including the 3 17.50 16.50 15.50 13.00 12.00 9.00 7.50 6.00 5.00 3.00
temperature rise of the contacts which is 4 16.50 15.50 15.00 12.50 11.00 8.50 7.00 5.50 4.50 3.00
a maximum of 30°C. There are several 5 16.00 15.00 14.00 12.00 10.50 8.00 6.50 5.50 4.50 3.00
variables which have a direct effect on 6 In-Line 15.50 14.50 13.50 11.50 10.00 8.00 6.50 5.00 4.00 2.50
this maximum current-carrying capabil-
6 Matrix 15.00 14.00 13.00 11.00 9.50 7.50 6.00 5.00 4.00 2.50
ity for a given connector and must be
8 14.50 14.00 13.00 10.50 9.50 7.50 6.00 5.00 4.00 2.50
considered for each application. These
variables are: 9 13.50 12.50 11.50 9.50 8.50 6.50 5.50 4.50 3.50 2.00
10 14.00 13.00 12.50 10.00 9.00 7.00 5.50 4.50 3.50 2.50
12 12.50 12.00 11.00 9.00 8.00 6.00 5.00 4.00 3.00 2.00
15 12.00 11.50 10.00 8.50 7.50 6.00 4.50 4.00 3.00 2.00
internal resistance to current flow and
thus generates less heat. Longer wire Values are based on initial Temperature Rise versus Current Testing and are intended to be a guide in the selection
lengths also enhance current carrying of a connector family. All applications should be tested by the end user. The values listed are per circuit for fully
capabilities since the wire conducts heat loaded housings being 100% energized. Note: All combinations were not tested, and this chart contains interpolated
away from the connector. and extrapolated values.

Minimum Wire Lengths for T-Rise vs. Current Testing
can be carried.
AWG Min. Length (in.) AWG Min. Length (in.)
Ambient Temperature—The higher
30 2.6 18 9.4
the ambient temperature, the less current
26 4.1 14 13.7
Printed Wiring Board Conductor
24 5.1 12 16.4
Size—The finished trace conductor
20 7.8 10 19.3
width and thickness should be maxi-
mized to allow for the greatest current Note: If wire lengths used are less than those listed above, the current
carrying capacity and heat dissipation. carrying ability of the system will be reduced due to less heat being
conducted away from the connector. The customer should fully test
all applications.
Standard Density
Universal MATE-N-LOK connectors also

will withstand the following tests: Wire-to-Board
Vibration—10-55-10 cycles per Due to the vast differences in trace geometry and printed circuit board configurations, we are unable to provide a
minute at .06 inch total excursion separate current carrying chart for our printed circuit board header products. However, the above Wire-to-Wire charts
may be used as a guideline for headers if the trace width and thickness is equal to the listed wire gauge. For vertical
Physical Shock—18 drops, 50 G headers, only 95% of the Wire-to-Wire value should be used. For right-angle headers, only 75% of the Wire-to-Wire
sawtooth at 10 milliseconds value should be used. The chart values are only a tool for connector selection and will require the customer to fully
test their application.
Housing Panel Retention—
75 lb. min.
Housing Lock Strength—30 lb. min.
Termination Contact
Thermal Shock— -55°C to +85°C Resistance Crimp
Temperature-Humidity Cycling— Test Resistance
25°C to 65°C at 95 RH (Amps) (Max. Init.) lbs. N
Corrosion—48 hr. at 5% salt 30 .05 — — 2 9
concentration 28 .08 — — 3 13
26 .12 — — 6 27
24 .2 1.5 3.50 8 36
22 .3 3 3.50 14 62
Related Product Data 20 .5 4.5 3.00 14 62
Product Specifications 18 .8 6 3.00 30 133
108-1031 Universal MATE-N-LOK 16 1.2 8 2.75 45 200
Connectors 14 2.0 10 2.75 50 222
108-1053 Universal MATE-N-LOK 12 3.0 — — 60 267
Headers 10 5.0 — — 70 311
Note: This is the total resistance between wire crimps of a mated pin and socket.
170
Soft Shell
Universal MATE-N-LOK Connector Mating Combinations

Connector Part Number7 Mating Connector Part Number
PC Board Headers7
Number Plug Cap Vertical Pin2 Vertical Socket2 Right-Angle2
of Flammability Style Part Part
Rating Plating Standard Standard Standard
Circuits Number2 Number2 Long Standard Long
Tail Tail Pin Socket
Tail Tail Tail Tail
Polarized Polarized
UL94V-2 — 1-350867-0 770421-1 — — — — — — — — —
1
UL94V-0 — 350865-1 350866-1 — — — — — — — — —
1-480699-0 Pre-tin 350428-1 641963-1 350582-1 350759-4 643411-1 350986-4 — —
UL94V-2 In-Line 1-480698-0
794814-13 794815-13 Duplex1 350428-4 641963-3 350582-4 350759-5 — — — —
2 641964-1
Pre-tin 350786-1 350787-1 350824-1 643412-1 350831-1 1-350942-0 643226-1
UL94V-0 In-Line 350777-1 350778-1 1-641964-15
Duplex1 350786-3 641964-3 350787-3 350824-4 643412-3 — 3-350942-0 —
UL94V-2 In-Line6 1-480700-0 1-480701-0 Pre-tin 350429-1 641965-1 350583-1 350760-4 643413-1 350987-4 — —
794901-13 794900-13 Duplex1 350429-4 — 350583-4 350760-5 — — — —
3 641966-1
Pre-tin 350789-1 350790-1 350825-1 643414-1 350832-1 1-350943-0 643228-1
UL94V-0 In-Line 350766-1 350767-1 1-641966-14
Duplex1350789-3 — 350790-3 350825-4 643414-3 350832-4 3-350943-0 3-643228-0
1-480703-0 Pre-tin 350430-1 641967-1 350584-1 350761-4 643415-1 350988-4 1-350948-0 —
UL94V-2 In-Line 1-480702-0
794899-13 794707-13 Duplex1 350430-4 — 350584-4 350761-5 — 350988-5 — —
4
Pre-tin 350792-1 641968-1 350793-1 350826-1 643416-1 350833-1 1-350944-0 643230-1
UL94V-0 In-Line 350779-1 350780-1
Duplex1 350792-3 — 350793-3 350826-4 — 350833-4 3-350944-0 3-643230-0
UL94V-2 In-Line 1-480763-0 1-480764-03 Pre-tin 640466-1 643405-1 — 640467-1 — — 1-350949-0 —

794863-13 Duplex1 640466-3 — — 640467-3 — — — —
5
Pre-tin 640900-1 643406-1 — 640901-1 — — 1-350945-0 643232-1
UL94V-0 In-Line 350809-1 350810-1
Duplex1 640900-3 — — 640901-3 — — 3-350945-0 3-643232-0
Pre-tin 641832-1 643407-1 — — — — 640587-1 —
UL94V-2 In-Line 640585-1 926307-1
Duplex1 641832-3 — — — — — — —
Pre-tin 641831-1 643408-1 — 770262-1 — — 640583-1 643234-1
UL94V-0 In-Line 640581-1 926307-3
Duplex1 641831-3 — — 770262-3 — — 640583-3 3-643234-0
6
1-480704-0 1-480705-0 Pre-tin 350431-1 641969-1 350585-1 350762-4 643423-1 350989-4 — —
UL94V-2 Matrix6 794535-13 794536-13 Duplex1 350431-4 — 350585-4 350762-5 — 350989-5 — —
794096-15
Standard Density
Pre-tin 350711-1 641970-1 350732-1 350827-1 643424-1 350834-1 — —
UL94V-0 Matrix 350715-1 350781-1
Duplex1 350711-4 641970-3 350732-4 350827-4 643424-3 350834-4 — —
Pre-tin 641825-1 — 770143-1 — — — — —
UL94V-2 In-Line 640586-1 926308-1
Duplex1 — — — — — — — —
8
Pre-tin 641828-1 643410-1 — — — — 640584-1 643236-1
UL94V-0 In-Line 640582-1 926308-3
Duplex1 — 643410-3 — — — — 640584-3 3-643236-0
1-480707-0 Pre-tin 350432-1 641971-1 350586-1 350763-4 643425-1 350990-4 — —
UL94V-2 Matrix 1-480706-0
794537-13 794538-13 Duplex1 350432-4 641971-3 350586-4 350763-5 — 350990-5 — —
9 641972-1
Pre-tin 350712-1 350742-1 350828-1 643426-1 350835-1 — —
UL94V-0 Matrix 350720-1 350782-1 1-641972-14

Duplex1 350712-4 641972-3 350742-4 350828-4 643426-3 350835-4 — —
Pre-tin — — — — — — — —
UL94V-2 In-Line 926302-1 926309-1
Duplex1 — — — — — — — —
10
Pre-tin — — — — — — — —
UL94V-0 In-Line 926302-3 926309-3
Duplex1 — — — — — — — —
1-480709-0 Pre-tin 350433-1 641973-1 350587-1 350764-4 — 350991-4 — —
UL94V-2 Matrix 1-480708-0
794851-13 794727-13 Duplex1 350433-4 — 350587-4 350764-5 — 350991-5 — —
12 641974-1
Pre-tin 350713-1 350737-1 350829-1 643428-1 350836-1 — —
UL94V-0 Matrix 350735-1 350783-1 1-641974-14
Duplex1350713-4 641974-3 350737-4 350829-4 — 350836-4 — —
1-480711-0 Pre-tin 350434-1 641975-1 350588-1 350765-4 643429-1 350992-4 — —
UL94V-26 Matrix 1-480710-0
794546-13 794545-13 Duplex1 350434-4 — 350588-4 350765-5 — — — —
15
Pre-tin 350714-1 641976-1 350738-1 350830-1 643430-1 350837-1 — —
UL94V-0 Matrix 350736-1 350784-1
Duplex1 350714-4 641976-4 350738-4 350830-4 — 350837-4 — —
1Duplex Finish — Plated with .000030 [.000762] min. gold in mating area, 3Housing material has 125°C temperature rating.
matte tin on solder tail end over .000050 [.00127] min. nickel underplate 4Black in color.
on entire contact. 5Tool Removable
2Universal MATE-N-LOK Plug and Cap housings accept pin or socket con- 6UV Resistant housing material available.
tacts. Use the appropriate contacts in the Plug housing as required by the 7European glow wire housing material available.
mating component.

171
Soft Shell
Contacts Related Product Data

Solid pin diameter .084 [2.13] Product Specification
Stock thickness .012 [.305] unless 108-1031 Universal MATE-N-LOK
otherwise noted. Connectors
These contacts can be used in either Application Specification
Universal MATE-N-LOK Plug or Cap 114-1010 Universal MATE-N-LOK
housings only. Contacts
Performance Characteristics— Solid Pin Socket
pages 169-170
Technical Documents— pages 169 and
205-206
Application Tooling— pages 207-210
Housings—page 174

Ins. Dia. L Dim. Hand Tool
Range Material & Finish Pin Socket Applicator
AWG [mm2] Range Pin Socket Part No. Part No.
Strip Form Loose Piece Strip Form Loose Piece
30-26 .032-.057 .790 .760 Brass, Pre-tin 350924-1 770672-1 350925-1 770673-1 466616-26 58439-1
[.05-.12] .813-1.45 20.06 19.30 Phos. Brz., Gold2 350924-6 770672-6 350925-6 — 466616-36
350851-1
Brass, Pre-tin 350561-1 350690-1 350689-11
350570-11
350851-2 640347-2
Brass, Gold2 350561-2 350690-2 466320-16
24-18 .040-.100 .790 .760 350570-21 350689-21
466320-26 91510-1
[.2-.8] 1.02-2.54 20.06 19.30 350851-7
Brass, Select Gold3 350561-7 350690-7 350689-71 466320-46
350570-71
Phos. Brz., Pre-tin 350561-3 350690-3 350570-3 1 350689-31
Phos. Brz., Select Gold3 — — 350570-61 —
Brass, Pre-tin 350218-1 350547-1 350536-1 350550-1
Brass, Gold2 350218-2 350547-2 350536-2 350550-2 687763-16
20-14 .060-.130 .790 .760
[.5-2.0] Brass, Select Gold3 350218-7 350547-7 350536-7 350550-7 687763-26 91500-1
1.52-3.30 20.06 19.30
Phos. Brz., Pre-tin 350218-3 350547-3 350536-3 350550-3 687763-66
Brass, Pre-tin 350538-1 350552-1 350537-1 350551-1
20-14
Standard Density
Brass, Gold2 350538-2 350552-2 350537-2 350551-2 687926-16

[.5-2.0] .130-.200 .810 .780
or Brass, Select Gold3 350538-7 350552-7 350537-7 350551-7 687926-26 91508-17
2@18 3.30-5.08 20.57 19.81 687926-66 91506-17
Phos. Brz., Pre-tin 350538-3 350552-3 350537-3 350551-3
[.8]
18-144 .130-.200 .810 .780 Brass, Pre-tin 350873-1 — 350874-1 — 466588-16 91508-17
466588-26
[.8-2.0] 3.30-5.08 20.57 19.81 Phos. Brz., Pre-tin 350873-3 350918-3 350874-3 350919-3 466588-36 91506-17
Phos. Brz., Pre-tin 350922-3 640309-3 350923-3 640310-3 466597-16

12-10 .200 max.5 .810 .780 466597-26 69710-17
[3.0-5.0] 5.08 20.57 19.81 Phos. Brz., Select Gold3 350922-6 640309-6 350923-6 640310-6 466597-36
1Socket Contact — .010 [.254] stock thickness

4Recommended for predominant use of 14 AWG wire.
5There is no insulation barrel on this contact. Insulation maximum diameter is limited by the housing.
Machine, -3, -4 & -6 are used on AMP-O-LECTRIC Model G Machine. See pages 207-210 for further information.
7Hand Tool No. 91508-1 is for wire size 20-18 AWG. Hand Tool No. 91506-1 is for wire size 16-14 AWG. Hand Tool No. 69710-1 use die set No. 58380-1 for 12
AWG and No. 58380-2 for 10 AWG.
Note: Phosphor bronze material contacts should be used in high temperature/humidity cycling applications.
Contact Retention Test Tool Contact Extraction Tool Contact Insertion Tool
Part No. 1586701-1 Part No. 318851-1 (For inserting contacts applied
IS 408-10003 IS 408-4371 to small diameter wire)
Part No. 91002-1
IS 408-7347
172
Soft Shell
Contacts Split Pins

Split pin diameter .086 [2.18]
These contacts can be used in either
Universal MATE-N-LOK Plug or Cap
housings only. HDM
Wire Size Range Ins. Dia. L Contact Part Number Hand Tool
Material & Finish Applicator
AWG [mm2] Range Dim. Part No.
Related Product Data Strip Form Loose Piece Part No.
Product Specification Brass, Pre-tin 350699-1 350706-1 466320-13
24-18 .040-.100 .790 Brass, Gold1 350699-2 350706-2 466320-23 91510-1
108-1031 Universal MATE-N-LOK [.2-.8] 1.02-2.54 20.06 466320-43
Connectors Brass, Select Gold2 350699-7 350706-7
Brass, Pre-tin 350687-1 350705-1 687763-13
Application Specification 20-14 .060-.130 .790 Brass, Gold1 350687-2 350705-2 687763-23 91500-1
114-1010 Universal MATE-N-LOK [.5-2.0] 1.52-3.30 20.06 687763-63
Brass, Select Gold2 350687-7 350705-7
Contacts 20-14 Brass, Pre-tin 350700-1 350707-1
[.5-2.0] 687926-13
Performance Characteristics— .130-.200 .810 Brass, Gold1 350700-2 350707-2 687926-23 91508-14
or 3.30-5.08 20.57
pages 169-170 2@18 [.8] Brass, Select Gold2 350700-7 350707-7 687926-63 91506-14
Technical Documents— pages 169
1Gold Finish — Plated with .000030 [.000762] min. gold in mating area and inside wire barrel over .000050 [.00127]
and 205-206
min. nickel underplate on entire contact.
Application Tooling— pages 207-210 2Select Gold Finish — Plated with .000030 [.000762] min. gold in mating area over .000050 [.00127] min. nickel
Housings—page 174 underplate on entire contact.
3HDM Applicator part number ending in -1, is used on AMPOMATOR CLS Machine with T or G Terminators, -2 is
used on AMP-O-LECTRIC Model K Machine, -4 & -6 are used on AMP-O-LECTRIC Model G Machine. See
pages 207-210 for further information.
4Hand Tool No. 91508-1 for wire size 20-18 AWG. Hand Tool No. 91506-1 for wire size 16-14 AWG.
Notes:
1. Split pins recommended for use in housings having 6, 9, 12 and 15 circuits to reduce mating force.
2. Phosphor bronze material contacts are available for use in high temperature/humidity cycling applications,
consult Tyco Electronics.
Grounding Pins
(.100 [2.54] longer than standard pin)
current)
Standard Density
Contact Part Number HDM
Wire Size Range Ins. Dia. L Applicator Hand No.
Tool
Material & Finish
AWG [mm2] Range Dim. Strip Form Loose Piece Part No. Part
24-18 .060-.130 .890 567216-22
[.2-.8] 1.52-3.30 22.60 Brass, Pre-tin 770210-1 — 567216-32 —
687763-1 2
20-14 .060-.130 .890 Brass, Pre-tin 350654-1 350669-1 687763-22 91500-1
[.5-2.0] 1.52-3.30 22.60 687763-62
466597-12
12-10 .200 max.1 .910 Phos. Brz., Pre-tin 770234-3 — 466597-22 —
[3.0-5.0] 5.08 23.11

466597-32
1There is no insulation barrel on this contact. Insulation maximum diameter is limited by the housing.
used on AMP-O-LECTRIC Model K Machine, -3 & -6 are used on AMP-O-LECTRIC Model G Machine. See pages
207-210 for further information.
Programmable Connector .048

[1.22] Dia.
Contact
(Socket with 110 Series Special
FASTON Tab) .805
[20.45]
Material and Finish

Part Number
Brass, pre-tin
350877-1
Note: This contact will accept a 110

Series FASTON Receptacle — Part
No. 350871-1 (strip form) allowing
simple field wiring or wiring changes.
173
Soft Shell
Housings 2, 3, 4, 5, 6, 8 and 10
Free-Hanging or Panel Mount Circuit, In-Line
.460 .300
.300 [11.68] [7.62]
[7.62] 1.080 1.080 .620
.580 [15.75]
[14.73] [27.43] [27.43]
Plug Cap
1 Circuit, Free-Hanging 6 Circuit, Matrix
.290
[7.37] .550
.550
[13.97]
[13.97]
.460
.290 [11.68]
[7.37] 1.080
.800
[27.43] .460 [20.32]
Plug [11.68] 1.080 1.120
1.080 1.080
[27.43] [27.43] [28.45]
[27.43] Plug Cap
.380
[9.65]
9, 12 and 15 Circuit,
Matrix
1.080 .380
[27.43] [9.65]
Cap
.800 .460 .800

[11.68] 1.080 [20.32]
[20.32]
1.080 [27.43]
1.080 1.120
[27.43] [28.45]
[27.43] Plug Cap
Related Product Data Housing Part Numbers

Number of A UL94V-2 Nylon, Natural Color2 UL94V-0 Nylon3
Standard Density
Product Specification Circuits Dim.

108-1031 Universal MATE-N-LOK Plug Cap Plug Cap
Connectors 1 — 1-350867-0 770421-1 350865-1 350866-1
.550
Performance Characteristics— 2 13.97 1-480698-01 1-480699-01 350777-11 350778-11
pages 169-170 .800
Contacts—pages 172-173 3 20.32 1-480700-01 1-480701-01 350766-11 350767-11
Panel Cutout 1.050
4 1-480702-01 1-480703-01 350779-11 350780-11
Recommendations— page 175 26.67
Keying Plug— page 175 1.300
5 33.02 1-480763-01 1-480764-01 350809-11 350810-11
Strain Reliefs— pages 175-176
Technical Documents— pages 169 1.550
39.37 640585-11 926307-11 640581-11 926307-31

and 205-206 6
Mating Headers—pages 182-183 1-480704-0
— 1-480705-0 350715-1 350781-1
and 185 794096-14
Other Mating Connectors 2.050
8 640586-11 926308-11 640582-11 926308-31
Universal MATE-N-LOK II Housings— 52.07
pages 193-194 9 .800 1-480706-0 1-480707-0 350720-1 350782-1
20.32
2.550
10 64.77 926302-11 926309-11 926302-31 926309-31
Note: See charts on page 182 to
order Plug and Cap Housings in 1.050
12 26.67 1-480708-0 1-480709-0 350735-1 350783-1
colors.
1.300
15 33.02 1-480710-0 1-480711-0 350736-1 350784-1
1In-Linestyle.
2Housing material has 125°C temperature rating.
3Housing material has 120°C temperature rating.
4Tool Removable.
174
Soft Shell
Recommended Number of Dimensions

Style
Cap Housing Circuits A B C D E
Panel Cutouts 2 .565 .340 .095 .530 .250
14.35 8.64 2.41 13.46 6.35
View is from cap entry side .815 .340 .095 .530 .250
3 20.70 8.64 2.41 13.46 6.35
1.065 .340 .095 .530 .250
Refer to Application Specification 4 27.05 8.64 2.41 13.46 6.35
114-1010
1.315 .340 .095 .530 .250
In-Line 5 33.40 8.64 2.41 13.46 6.35
1.567 .154 .189 .531 .394
6 39.80 3.91 4.80 13.49 10.0
2.067 .154 .189 .531 .394
8 52.50 3.91 4.80 13.49 10.0
2.567 .154 .189 .530 .394
10 65.20 3.91 4.80 13.46 10.0
.565 .480 .275 1.030 .250
6 14.35 12.19 6.99 26.16 6.35
.815 .480 .275 1.030 .250
9 20.70 12.19 6.99 26.16 6.35
Matrix
12 1.065 .480 .275 1.030 .350
27.05 12.19 6.99 26.16 8.89
1.315 .480 .275 1.030 .350
15 33.40 12.19 6.99 26.16 8.89
Notes:
1. Recommended panel thickness — .030-.090 [.762-2.286]. Panel must be punched so that housing enters panel in
same direction as the punch.
2. Optional — Do not remove this material when keying cap housing to panel.
3. Circuit #1 location when using panel keying with 6, 9, 12 and 15 circuit Matrix housings.
4. Circuit #1 location when using panel keying with 2, 3, 4, 5, 6, 8 and 10 circuit In-Line housings.
5. .175 [4.45] dimension is .125 [3.18] for 6, 8 and 10 circuit In-Line housings.
Keying Plugs
IS 408-3320
Standard Density
Part Numbers
UL94V-2 Nylon material, natural color — 1-640415-1
UL94V-0 Nylon material — 1-640415-0
Note: Keying plug snaps into plug or cap housing
Plug Housing 2, 3, 4, 5, 6 and 8 Circuit, In-Line 6, 9, 12 and 15 Circuit, Matrix

Strain Reliefs 2 Req’d/Assy.
Wire Bundle Dia.—
IS 408-3320 See Note
.500 Max.
Wire Bundle Dia.— [12.7]
.312 2 Req’d/Assy.

Max. See Note
[7.92]
.600
[15.24]
.600
[15.24]

Plug Housings— page 174
and 205-206 1.375
1.375
[34.93] [34.93]
(2) #6x5 ⁄ 8 Lg Type B (2) #6x5 ⁄ 8 Lg Type B

Pan head sheet .530 Pan head sheet
metal screws [13.46] metal screws
(not supplied) .530
(not supplied) [13.46]
Part Numbers Part Numbers
UL94V-2 Nylon material, natural color — 1-350589-0 UL94V-2 Nylon material, natural color — 1-350590-0
UL94V-0 Nylon material — 350811-1 UL94V-0 Nylon material — 350812-1
Note: Strain relief part number represents one half of a strain relief. Two strain reliefs required per housing.
175
Soft Shell

Cap Connector
Plug or 2, 3, 4, 5, 6, 8, 9,
Cap Housing 12 and 15 Circuit
Strain Reliefs (Enclosed)
IS 408-3320

Housings— page 174 Adapter
Note 4
Technical Documents— pages 169 Enclosed Strain
and 205-206 Relief
2 Req’d/Assy.
Note 3
(2) #6x5/8 Lg Type B

2 Req’d/Assy. Pan head sheet metal
Note 3 screws (not supplied) 2 Req’d/Assy.
Note 3
1.300
1.300
Cap Housing Adapters [33.02]
Note 2 [33.02]
Note
2
These adapters are designed to anchor
the cap housing strain reliefs to the
housings and prevent the strain relief
halves from “drawing in” when the Note 1
screws are being torqued down to clamp (2) #6x3/8 Lg Type B
Pan head sheet metal
the cable. screws (not supplied) Matrix
In-Line Insert
IS 408-3320
Part Numbers
For All Positions Except 2, 6 Style
Number of A Insert Single Wire Wire Bundle
Circuits Dim. Supplied Dia. Range Dia. Range UL94V-2 Nylon,
and 8 Circuit Cap Housings Natural Color UL94V-0 Nylon
.630 .040-.190
Yes 1.02-4.83 — 1-640719-0 640713-1
[16.0] .960
2 24.38 .200-.350
No — 1-640719-1 640713-2
5.08-8.89
.040-.190
Yes 1.02-4.83 — 1-640720-0 640714-1
1.140
Standard Density
3
.550 28.96 .200-.350
[13.97] No — 641763-1 641945-1
5.08-8.89
.040-.190
Yes 1.02-4.83 — 641775-1 641776-1
1.325
4 33.65 .200-.350
In-Line No — 5.08-8.89 641775-2 641776-2
UL94V-2 Nylon material,
natural color — 641777-1 .040-.190
Yes 1.02-4.83 — 643030-3 643030-1
1.530
UL94V-0 Nylon material — 5 38.86 .200-.350
641778-1 No — 643030-2 643030-4
5.08-8.89
.040-.190
Yes 1.02-4.83 — 643585-1 643313-1
1.780
For 2 In-Line and 6 Matrix 6 45.21 .200-.350
Circuit Cap Housings Only Note 5 No — 643585-2 643313-2
5.08-8.89
.040-.190
Yes 1.02-4.83 — — 643314-1
.630 2.280
[16.0] 8 56.08 .200-.350
Note 5 No — — 643314-2
5.08-8.89
1.030 .120-.650
6 26.16 Yes — 3.05-16.51 1-640721-0 640715-1
.480 1.030 .120-.650

9 26.16 Yes — 3.05-16.51 1-640722-0 640716-1
[12.19]
Matrix
1.280 .150-.750
12 Yes — 1-640723-0 640717-1
32.51 3.81-19.05
1.530 .200-.850
15 38.86 Yes — 5.08-21.59 1-640724-0 640718-1
UL94V-2 Nylon material,
natural color — 643182-1 Notes:
UL94V-0 Nylon material — 1. Cable clamping insert comes attached to strain relief. It can be used to provide additional adjustment for small wire
643182-2 bundles or discarded.
2. Insert to be positioned as shown by dotted lines.
3. Strain relief part number represents one-half of a strain relief. Two strain reliefs required per housing.
4. Must use cap housing adapters when attaching strain reliefs to a cap housing. Two adapters required per housing.
5. Strain reliefs for 6 and 8 circuit In-Line fits plug housings only.

176
Soft Shell
Universal MATE-N-LOK Flanged Cap Housings with Twist and Lock Feature
Product Facts
■ Available in a 6, 9, and 12
circuit design
■ Designed for household
appliances where a
bulkhead connector system
is needed in conjunction
with foam-in insulation
■ Mates with standard
Universal MATE-N-LOK plug
housings (page 174)
■ Accepts Universal
MATE-N-LOK pin and socket
contacts (page 167)
■ Designed to utilize the
Splash Proof/Sealed
Universal MATE-N-LOK
seals for additional sealing
protection (pages 174-175)
.115
[2.92]
1.365 Dia.
[34.67]
.010
[0.25]
Material and Finish
Housing—Nylon, UL 94V-0 or .185
UL 94V-2 rated [4.69]
Contacts—Phosphor Bronze or Brass 1.145 Dia.

[29.08]
Plating—Pre-tin or Gold
.290
Standard Density
[7.36]
Recommended Panel Cutout
Contacts—pages 172-173 (for 6 and 9 Pos. Housings)
Plug Housings—page 174 .800
[20.32]
Seals—page 180
2.000
Dia.
[50.80]
.675
[17.15] Radius
2 Plc.

Universal MATE-N-LOK Flanged Cap Housings
.550
[13.97]
.510
[12.95]
1.080
[27.43]
Notes:
1. Recommended Panel Thickness: Number of Cap Housing Part Numbers
0.76-2.29 [.030-.090] Circuits UL 94V-0 UL 94V-2
2. Panel must be punched so that
the housing enters the panel in 6 794760-1 794714-1
the same direction as the punch. 9 794761-1 794715-1
3. Asymmetrical panel cutout pro-
vides polarization for Pin 1 loca- 12 794762-1 794716-1
tion.

177
Soft Shell
Universal MATE-N-LOK Sealed

Connectors
Bulkhead Connectors
(Continued)
Product Facts
■ Bulkhead mount Universal
MATE-N-LOK connector
that facilitates sealed
panel mounting and works
with existing Universal
MATE-N-LOK seals to
provide a fully-sealed
interconnection system
■ Available in 4, 6, 9 and 12
positions
■ Sealed, flange mount
design
■ Mates to standard Universal
MATE-N-LOK plug housings
■ Accepts standard Universal
MATE-N-LOK contacts
■ Works with standard
connector interface and
wire seals
■ Anti-rotation feature aids
installation
■ Rear mount flange design
enables use in wire
harnesses
housing
■ UL Recognized, Performance Characteristics Technical Documents
File No. E28476
Standard Density
Dielectric Withstanding Voltage— Product Specification

■ CSA Certified, R 5.0 KVAC or 5.0 KVDC between 108-1031 Universal MATE-N-LOK
File No. 1030930 adjacent circuits Connectors
Insulation Resistance— Application Specification
1000 megohms minimum initial 114-1010 Universal MATE-N-LOK
between adjacent circuits Contacts
Applications Voltage Rating—600 V AC or DC Instruction Sheet
■ Vending Machines Durability—50 cycles, mating 408-10017 Universal MATE-N-LOK
and unmating Bulkhead Connectors
■ Industrial Machinery
■ Lighting
Universal MATE-N-LOK Sealed Bulkhead Connectors
■ HVAC Equipment
178
Soft Shell

Connectors
Bulkhead Connectors (Continued)
(Continued)
Connector Housings 4 Position Connector Housing

(shown)
Material and Finish

Housing—Nylon, UL 94V-0 rated
Contacts—Brass with pre-tin or gold
plating
O-ring Seal—Neoprene
Locking Nut—Steel, zinc plated
1.050
[26.67]
1.160
.750 [29.46]
[19.05]
.980 .300
[24.89] [7.62] 1.500
[38.10]
1.680
[42.67]
Standard Density
1.000 1.480
[25.40] Ø1.320 [37.59] Ø1.660
[33.53] [42.16]

Universal MATE-N-LOK Sealed Bulkhead Connectors
Recommended Recommended
Panel Cut-Out for 4, 6 & 9 Position Product Only Panel Cut-Out for 12 Position Product Only
No. of Pos. Style Housing Part Number

4 In Line 1604256-1
6 Matrix 1604210-1
9 Matrix 1604254-1
12 Matrix 1604941-1
179
Soft Shell

Connectors
Connectors
(Continued)
Splash Proof Seals Material

Silicone rubber, blue color
Product Facts Technical Documents
■ Economical splash proof/ Product Specification Note: For proper use of this product, customer should make sure
immersible sealed connec- 108-1031-1 Splash Proof Seal, that Instruction Sheet 408-3392 is available for review.
tor system Universal MATE-N-LOK
Connectors
■ No design changes to exist- Contacts—page 175
ing Universal MATE-N-LOK Housings—page 174
product
Instruction Sheet
■ Existing applications utiliz- 408-3392 Universal MATE-N-LOK
ing Universal MATE-N-LOK Splash Proof Seals Mating
connectors can be upgraded Plug Housing End
to a splash proof system Wire Seal
■ Utilizes two wire seals and

one interface seal Contact Cap Housing
Cavity
■ Wire range is 20-14 AWG
[.5-2.0] with insulation
diameter range .060-.130
[1.52-3.30]
■ .110-.130 [2.79-3.30]
Wire Seal
insulation diameter passed Interface
European IP sealing level Seal
5/6 + 7 (swirling dust/ Pin Contact
Silos
immersion to 1 meter for
30 minutes) Back Side
(Wire End)
■ .060-.110 [1.52-2.79]
insulation diameter passed
European IP sealing level Number of A Interface Seal Interface Seal Wire Seal
Sealing Plug
5/5 + 7 (swirling dust/ Part Number 770377-1
Circuits Dim Part Number Low Mating Force* Part Number
heavy seas) 2 .550 794269-1 794991-1 794270-1
Standard Density
3 .800 794271-1 794992-1 794272-1

■ Universal MATE-N-LOK II
4 1.050 794273-1 — 794274-1
keying plug can be used to
6 — 794275-1 794993-1 794276-1
seal unused circuits
9 .800 794277-1 794994-1 794278-1
■ Primary application is for 12 1.050 794279-1 — 794280-1
wire-to-wire; wire-to-board 15 1.300 794281-1 — 794282-1
application must use a Note: One interface seal and two wire seals required per mated assembly.
closed bottom header *Low mating force interface seals do not meet IP 5/6 IP 5/7 requirements.
Universal MATE-N-LOK Sealed Connectors
2, 3, 4 Circuit, In-Line 6 Circuit, Matrix 9, 12, and 15 Circuit, Matrix

.800
.800 [20.32]
.300 .800 [20.32]
.300 [7.62] [20.32]
A
[7.62]
.550 .550 A A
[13.97] [13.97]
A
.400
.030 .400 .800 .030
[10.16]
[.762] [10.16] .030 [20.32] .400 [.762]
[.762] [10.16]
Wire interface Wire interface Wire interface
180
Soft Shell

Connectors
Connectors
(Continued)
(Continued)
Contacts (used with

Splash Proof Seals)
Solid pin diameter .084 [2.13]
Split pin diameter .086 [2.18]
Stock thickness .012 [.305] unless
otherwise noted.
These contacts can be used in either
Universal MATE-N-LOK Plug or Cap
Solid Pin Split Pin Socket
housings only.
108-1031 Universal MATE-N-LOK
Connectors
Contacts
Grounding Pin
Performance Characteristics— (.100 [2.54] longer than standard pin)
pages 169-170 (Mate first, break last, not for interrupting
Technical Documents— pages 169 current)
and 205-206
Housings—page 174

Ins. Dia. L Dim.
Range Material & Finish Style Pin Socket Applicator Hand Tool
AWG [mm2] Range Pin Socket Part No. Part No.
Strip Form Loose Piece Strip Form Loose Piece
Brass, Pre-tin 350218-1 350547-1 350536-1 350550-1
Brass, Gold1 350218-2 350547-2 350536-2 350550-2
Brass, Select Gold2 Solid 350218-7 350547-7 350536-7 350550-7
.790 .760 Phos. Brz., Pre-tin 350218-3 350547-3 350536-3 350550-3
20.06 19.30 Phos. Brz., Select Gold2 687763-13
20-14 .060-.130 350218-6 350547-6 350536-6 350550-6 687763-23 91500-1
[.5-2.0] 1.52-3.30 Brass, Pre-tin 350687-1 350705-1 — — 687763-63
Brass, Gold1 Split 350687-2 350705-2 — —
Standard Density
Brass, Select Gold2 350687-7 350705-7 — —
.890
22.60 — Brass, Pre-Tin Grounding 350654-1 350669-1
3HDM Applicator part number ending in -1, is used on AMPOMATOR CLS Machine with T or G Terminators, -2 is used on AMP-O-LECTRIC Model K
Machine, -4 & -6 are used on AMP-O-LECTRIC Model G Machine. See pages 207-210 for further information.
Notes:
1. Split pins recommended for use in housings having 6, 9, 12 and 15 circuits to reduce mating force.
2. Phosphor bronze material contacts are available for use in high temperature/humidity cycling applications,
consult Tyco Electronics.

Universal MATE-N-LOK Sealed Connectors
3. 18-24 AWG contacts (page 166) can be used with splash proof seals if insulation diameter range is .060-.100 [1.52-2.54].
Universal MATE-N-LOK II .130

.940
[23.88]
Keying Plug/Splash Proof [3.30]
Sealing Plug
IS 408-3392 Part Number
UL94V-0 Nylon material — 770377-1

Housings— page 174
and 205-206
Seal Latch Tool Contact Extraction Tool Contact Insertion Tool (For inserting
Part No. 794381-1 Part No. 318851-1 contacts applied to small diameter wire)
IS 408-3392 IS 408-4371 Part No. 91002-1
IS 408-7347
181
Soft Shell
PC Board Vertical 2, 3, 4, 5, 6 and 8 Polarizing

feature
Pin Headers Circuit, In-Line
.175 Standard Tail
.300
[4.45]
[7.62]
Material .235 Long Tail .550
[5.97] [13.97]
Housing —
UL94V-2 Nylon, natural color Mates with Plug
Housing Part Number
UL94V-0 Nylon Pin Header Part Numbers (Using Socket Contacts)
Number of A Flammability Pin
Contacts — Phosphor bronze Circuits Dim. Rating Finish Standard Standard Tail Universal Universal
Tail2 Polarized2 Long Tail3 MATE-N-LOK MATE-N-LOK II
Solder tail diameter .062 [1.57]
Pre-tin 350428-1 641963-1 350582-1
UL94V-2 1-480698-0 —
Duplex1 350428-4 641963-3 350582-4
.550
Related Product Data 2 641964-1
13.97 Pre-tin 350786-1 350787-1
UL94V-0 1-641964-14 350777-1 770017-1
Duplex1 350786-3 641964-3 350787-3
108-1053 Universal MATE-N-LOK Pre-tin 350429-1 641965-1 350583-1
PC Board Headers UL94V-2 1-480700-0 —
Duplex1 350429-4 — 350583-4
Performance Characteristics— .800
3 641966-1
20.32 Pre-tin 350789-1 350790-1
pages 169-170 UL94V-0 1-641966-14 350766-1 770018-1
Recommended PC Board Hole Duplex1 350789-3 — 350790-3
Layout— page 184
Pre-tin 350430-1 641967-1 350584-1
and 205-206 UL94V-2 Pre-tin 770351-15 — — 1-480702-0 —
4 1.050 Duplex1 350430-4 — 350584-4
26.67
Pre-tin 350792-1 641968-1 350793-1
UL94V-0 350779-1 770019-1
Mating Connectors Duplex1 350792-3 — 350793-3
Universal MATE-N-LOK Pre-tin 640466-1 643405-1 —
UL94V-2 1-480763-0 —
Plug Housings — page 174 1.300 Duplex1 640466-3 — —
5
33.02 Pre-tin 640900-1 643406-1 —
Universal MATE-N-LOK II UL94V-0 350809-1 770016-1
Duplex1 640900-3 — —
Plug Housings — pages 193-194
1.550 UL94V-2 Pre-tin 641832-1 643407-1 — 640585-1 —
6
39.37 UL94V-0 Pre-tin 641831-1 643408-1 — 640581-1 —
UL94V-2 Pre-tin 641825-1 — 770143-1 640586-1 —
2.050
Standard Density
8 UL94V-0 Pre-tin 641828-1 643410-1 770272-1 640582-1 —

52.07
UL94V-0 Duplex1 — 643410-3 770272-3 — —
Mates with Plug

6, 9, 12 and 15 Housing Part Number
Pin Header Part Numbers (Using Socket Contacts)
Number of A Flammability Pin
Circuit, Matrix Circuits Dim. Rating Finish Standard Standard Tail Universal Universal
Polarizing 641969-1 350585-1
Pre-tin 350431-1
feature UL94V-2 — 643749-15 1-480704-0 —
.550 Duplex1 350431-4 — 350585-4
6
13.97 641970-1
Pre-tin 350711-1 350732-1

.175 Standard Tail UL94V-0 1-641970-14 350715-1 770020-1
[4.45] Duplex1 350711-4 641970-3 350732-4
.235 Long Tail .550
[5.97] [13.97] Pre-tin 350432-1 641971-1 350586-1
UL94V-2 1-480706-0 —
Duplex1 350432-4 641971-3 350586-4
9 .800 641972-1
20.32 Pre-tin 350712-1 350742-1
UL94V-0 1-641972-14 350720-1 770021-1
Duplex1 350712-4 641972-3 350742-4
Pre-tin 350433-1 641973-1 350587-1
UL94V-2 1-480708-0 —
Duplex1 350433-4 — 350587-4
.800 1.050
[20.32] 12 641974-1
26.67 Pre-tin 350713-1 350737-1
UL94V-0 1-641974-14 350735-1 770022-1
Duplex1 350713-4 641974-3 350737-4
Pre-tin 350434-1 641975-1 350588-1
UL94V-2 1-480710-0 —
1.300 Duplex1 350434-4 — 350588-4
15
33.02 Pre-tin 350714-1 641976-1 350738-1
UL94V-0 350736-1 770023-1
Duplex1 350714-4 641976-4 350738-4
Note: Header Housings on pages
182-185 are available in colors
listed on page 188. Call Technical [.00127] min. nickel underplate on entire contact.
2Use Standard Tail for .062 [1.57] thick PC Board. 3Use Long Tail for .125 [3.18] thick PC Board.
Support for exact Part Numbers.
4Black in color. 5No drain holes, used w/ seals, page 180. Note: All part numbers are RoHS Compliant.
182
Soft Shell
PC Board Vertical 2, 3, 4, 5, and 6 Polarizing

Socket Headers Circuit, In-Line feature
.175 Standard Tail

Material [4.45] .300
.235 Long Tail .550 [7.62]
Housing — [5.97] [13.97]
UL94V-2 Nylon, natural color
UL94V-0 Nylon Mates with Plug
Housing Part Number
Socket Header Part Numbers (Using Pin Contacts)
Contacts — Phosphor bronze Number of A Flammability Socket
Circuits Dim. Rating Finish Standard Standard Tail Universal Universal
Solder tail diameter .062 [1.57] Tail2 Polarized2 Long Tail3 MATE-N-LOK MATE-N-LOK II
Pre-tin 350759-4 643411-1 350986-4
UL94V-2 1-480698-0 —
.550 Duplex1 350759-5 — —
Related Product Data 2
13.97 Pre-tin 350824-1 643412-1 350831-1
Product Specification UL94V-0 350777-1 770017-1
Duplex1 350824-4 643412-3 —
108-1053 Universal MATE-N-LOK Pre-tin 350760-4 643413-1 350987-4
PC Board Headers UL94V-2 1-480700-0 —
.800 Duplex1 350760-5 — —
3
Performance Characteristics— 20.32 Pre-tin 350825-1 643414-1 350832-1
UL94V-0 350766-1 770018-1
pages 169-170 Duplex1 350825-4 643414-3 350832-4
Recommended PC Board Hole Pre-tin 350761-4 643415-1 350988-4
Layout— page 184 UL94V-2 1-480702-0 —
1.050 Duplex1 350761-5 — 350988-5
Technical Documents— pages 169 4
26.67 Pre-tin 350826-1 643416-1 350833-1
and 205-206 UL94V-0 350779-1 770019-1
Duplex1 350826-4 — 350833-4
Pre-tin 640467-1 — —
UL94V-2 1-480763-0 —
Mating Connectors 5 1.300 Pre-tin 640467-3 — —
33.02 Pre-tin 640901-1 — —
Universal MATE-N-LOK UL94V-0 350809-1 770016-1
Duplex1 640901-3 — —
Plug Housings — page 174
1.550
6 UL94V-0 Duplex1 770262-3 — — 640581-1 —
Universal MATE-N-LOK II 39. 37
6, 9, 12 and 15 Polarizing
feature
Circuit, Matrix
Standard Density
.175 Standard Tail
.800
[4.45]
[20.32]
.235 Long Tail .550
[5.97] [13.97]
Mates with Plug

Housing Part Number
Socket Header Part Numbers (Using Pin Contacts)
Number of A Flammability Socket
Circuits Dim. Rating Finish Standard Standard Tail Universal Universal
Pre-tin 350762-4 643423-1 350989-4
UL94V-2 1-480704-0 —

.550 Duplex1 350762-5 — 350989-5
6
13.97 Pre-tin 350827-1 643424-1 350834-1
UL94V-0 350715-1 770020-1
Duplex1 350827-4 643424-3 350834-4
Pre-tin 350763-4 643425-1 350990-4
UL94V-2 1-480706-0 —
.800 Duplex1 350763-5 — 350990-5
9
20.32 Pre-tin 350828-1 643426-1 350835-1
UL94V-0 350720-1 770021-1
Duplex1 350828-4 643426-3 350835-4
Pre-tin 350764-4 — 350991-4
UL94V-2 1-480708-0 —
1.050 Duplex1 350764-5 — 350991-5
12
26.67 Pre-tin 350829-1 643428-1 350836-1
UL94V-0 350735-1 770022-1
Duplex1 350829-4 — 350836-4
Pre-tin 350765-4 643429-1 350992-4
UL94V-2 1-480710-0 —
1.300 Duplex1 350765-5 — —
15
33.02 Pre-tin 350830-1 643430-1 350837-1
UL94V-0 350736-1 770023-1
Duplex1 350830-4 — 350837-4
Note: Header Housings on pages [.00127] min. nickel underplate on entire contact.
182-185 are available in colors 2Use Standard Tail for .062 [1.57] thick PC Board.
listed on page 188. Call Technical 3Use Long Tail for .125 [3.18] thick PC Board.
Support for exact Part Numbers.
183
Soft Shell

.175 .250
Recommended 2, 3, 4, 5, 6 and 8 [4.45] [6.35]
Typ.
PC Board Circuit, In-Line .070
[1.78]
Dia. Typ.
Hole Layouts olarizing Hole
for Pin and Socket See Note
Vertical Headers No. 1 Position
2 Circuit
3 Circuit
Related Product Data 4 Circuit
Vertical Headers—pages 182-183 5 Circuit
6 Circuit
8 Circuit
Polarizing Hole
Polarizing Hole See Note
See Note .250 .175
Typ.
.250 .175 [6.35] [4.45]
Typ.
[6.35] [4.45]
6, 9, 12 and 15 No. 2 Circuit
No. 2 Circuit
Circuit, Matrix .250 .250
Typ. Typ. No. 1 Circuit
[6.35] No. 1 Circuit [6.35]
.070 Dia. Typ.
.070 Dia. Typ. [1.78]
[1.78]
.250 .175 .250 .175

Typ. Typ.
[6.35] [4.45] [6.35] [4.45]
Polarizing Hole Polarizing Hole

See Note See Note
No. 2 Circuit No. 2 Circuit
250 .250
Typ. Typ.
.35] .070 No. 1 Circuit [6.35] .070 No. 1 Circuit
Dia. Typ. Dia. Typ.
[1.78] [1.78]
Note: Polarizing hole .070 [1.78] Dia. required for polarized headers only.
PC Board Vertical
Pin Headers with
.250
ACTION PIN Contacts [6.35]
Standard Density
Material and Finish

Housing — PBT, black
Flammability Rating — UL94V-0 .299 .200 ± .004 Typ. .630
[7.59] [5.08 ± 0.10] Max.
[16.00]
Contacts — Copper alloy, plated with
tin over nickel on entire contact
Mates with Plug Housing
Part Number (Using Socket Contacts)
Related Product Data Number of
Circuits A Dim. Part Number Universal Universal
MATE-N-LOK MATE-N-LOK II
pages 169-170 .750 1-480698-0
2 173924-1 770017-1
Technical Documents — pages 169 19.05 350777-1
and 205-206 3 1.000 173925-1 1-480700-0 770018-1
25.40 350766-1
1.250 1-480702-0
108-5222 ACTION PIN Universal 4 31.75 173926-1 350779-1 770019-1
MATE-N-LOK Header Note: Install in PC Board with arbor tool.
Assembly
Mating Connectors .062 Ref.
[1.57]
Universal MATE-N-LOK 4 Circuit
Plug Housings — page 174 3 Circuit
Universal MATE-N-LOK II 2 Circuit

Plug Housings — pages 193-194 Dia. After
Reflow
.032 ± .002 .001-.003
.100 ± .004
[0.81 ± 0.05] [0.03-0.08]
[2.54 ± 0.10]
Note: Header Housings on pages .200 ± .004 .038 ± .001
[5.08 ± 0.10] .0003-.0012
182-185 are available in colors [0.97 ± 0.03 ] [0.01-0.03]
listed on page 188. Call Technical
Support for exact Part Numbers. Recommended PC Board Hole Layout PC Board Hole Dimensions
184
Soft Shell
PC Board Right-Angle 2, 3, 4, 5, 6 and 8 Circuit, In-line

Pin and Socket Headers .505
.150
[12.83] Dia.
.250 [6.35] Centerline spacing .060 Dia. Typ. [3.81]
[1.52] 2 Places
.680
[17.27]
Material
.100
Housing — Nylon .250 [2.54]
No. 1 Circuit [6.35]
Contacts — Phosphor bronze Typ.
.290
Solder tail width .052 [1.32] .250
Typ. [7.37]
[6.35]
Related Product Data Use 6-32 UNC Pan Head Screw
3/8 [9.53] long for mounting
Product Specification (Not Supplied)
108-1053 Universal MATE-N-LOK .360 Recommended PC Board Hole Layout
.160
PC Board Headers [4.06]
[9.14] .062 [1.57] Board Thickness
Performance Characteristics— Right-Angle Header Part Numbers

pages 169-170 Dimensions UL94V-2 UL94V-0
Technical Documents— pages 169 No. of Contact Mates with
Circuits A B C Finish Mates
and 205-206 Pin Socket Pin Socket Universal Universal
with MATE-N-LOK MATE-N-LOK II
1-350942-0 643226-1
Mating Connectors .550 1.245 .830 Pre-tin — — —
2 13.97 31.62 21.08 770994-12 — 350777-1 770017-1
Universal MATE-N-LOK Duplex1 — — — 3-350942-0 —
Plug Housings — page 174 .800 1.495 1.080 Pre-tin — — 1-350943-0 643228-1
3 — 350766-1 770018-1
20.32 37.97 27.43 Duplex1 — — 3-350943-0 3-643228-0
Universal MATE-N-LOK II
Plug Housings — pages 193-194 1.050 1.745 1.330 Pre-tin 1-350948-0 — 1-350944-0 643230-1
4 1-480702-0 350779-1 770019-1
26.67 44.32 33.78 Duplex1 — — 3-350944-0 3-643230-0
Note: Header Housings on pages 1.300 1.995 1.580 Pre-tin 1-350949-0 — 1-350945-0 643232-1
5 1-480763-0 350809-1 770016-1
33.02 50.67 40.13 Duplex1 — — 3-350945-0 3-643232-0
182-185 are available in colors
listed on page 188. Call Technical 1.550 2.245 1.830 Pre-tin 640587-1 643235-1 640585-1 640583-1 643234-1
6 640581-1 —
Support for exact Part Numbers. 39.37 57.02 46.48 Duplex1 — 640583-3 3-643234-0
2.050 2.745 2.330 Pre-tin — 640584-1 643236-1
8 643237-1 640586-1 640582-1 —
52.07 69.72 59.18 Duplex1 — 640584-3 3-643236-0
Standard Density
[.00127] min. nickel underplate on entire contact. 2Black in color.
Test Connectors 2, 3, 4 and 5 Circuit,

(with spring loaded In-Line
contacts)
Material
Plug Cap
Housing — Nylon

6, 9, 12 and 15 Circuit, .084 [2.13] Dia. Pin
Related Product Data Matrix Mates with

Universal
MATE-N-LOK
Mating Connectors — Housings and Sockets
headers having the same number of
circuits. The housings can have pin or
socket contacts, or a combination
of both. Plug Cap
Mating Housings — page 174
Mating Headers — pages 182-185
Number of Part Numbers
Other Mating Connectors
Circuits Plug Cap
Universal MATE-N-LOK II Housings—
pages 193-194 2 350848-2 350849-2
3 350848-3 350849-3
Notes: 4 350848-4 350849-4
1. Test probes have 5 amp maxi- 5 350848-5 350849-5
mum current rating. 1,000,000 6 350848-6 350849-6
cycles. 9 350848-9 350849-9
2. Test Connector housings are of 12 1-350848-2 1-350849-2
the same configuration as stan-
15 1-350848-5 1-350849-5
dard housings. Refer to page 23
for dimensional specifications. Note: All part numbers are RoHS Compliant.
185
Soft Shell
Universal MATE-N-LOK Circular

Connectors
Connectors
(Continued)
Product Facts
■ Unique product designed to
accommodate the specific
needs of the lighting
industry
■ Circular design allows the
connector to pass through
7/8 inch knock-out holes in
electrical fixtures and boxes
■ 6-position accommodates
most major electrical
industry requirements
■ Universal MATE-N-LOK
connector centerline
spacing maintains UL and
CSA approvals
■ Uses standard Universal
MATE-N-LOK contacts and
application tooling
■ Positive polarized housing
helps prevent incorrect
mating
■ UL Recognized,
File No. E28476
■ CSA Certified, R
File No. LR7189

Performance Characteristics Technical Documents
Voltage—600 V AC or DC Product Specification
Current—20 amps maximum per 108-2069 Universal MATE-N-LOK
Applications UL-1977 (6 position, fully ener- Circular Connector
■ Primary applications are in gized) Application Specification
Standard Density
the Lighting, Vending, and Dielectric Withstanding Voltage— 114-1010 Universal MATE-N-LOK
5 KVAC or KVDC Connectors
Appliance industries
Insulation Resistance—1000 MΩ
■ Applications where use of a
max. between adjacent circuits
completed harness that will
Durability—50 cycles mating and
pass through a 7/8 inch
unmating
knock-out is required
Contact Retention—
■ Provides the capability to 15 lb. minimum per contact
quickly disconnect
individual fixtures from
Universal MATE-N-LOK Circular Connectors
sensitive environmental
areas and perform
maintenance at other sites
186
Soft Shell
Universal MATE-N-LOK Circular

Connectors
Connectors
(Continued)(Continued)
Plug 45˚
Part No. 794911-1 2 Plc.
1.080
[27.43]
.460
[11.68]
.820
[20.83]
Ref.
.810
[20.57] Ref.
Cap 45˚
2 Plc.
Part No. 794912-1 1.080
[27.43]
.820
[20.83]
Standard Density
.810
[20.57]
Material and Finish

Housings—Nylon, UL 94V-2 rated

Universal MATE-N-LOK Circular Connectors
Contacts—pages 172-173
187
Soft Shell

— Available in Colors
Note: See corresponding Universal Base Part Number No. of Circuits Housing Material
MATE-N-LOK Plug and Cap Housing 480698 2 Plug V-2
Base Part Numbers on page 175. 480699 2 Cap V-2
Header Housings on pages 182-185 480700 3 Plug V-2
are also available in colors. Call 480701 3 Cap V-2
Technical Support for exact Part
Numbers. 480702 4 Plug V-2
480703 4 Cap V-2
480763* 5 Plug* V-2
480764* 5 Cap* V-2
480704 6 Plug V-2
480705 6 Cap V-2
480706 9 Plug V-2
480707 9 Cap V-2
480708 12 Plug V-2
480709 12 Cap V-2
480710 15 Plug V-2
480711 15 Cap V-2
350777 2 Plug V-0
350778 2 Cap V-0
350766 3 Plug V-0
350767 3 Cap V-0
350799 4 Plug V-0
350780 4 Cap V-0
350809 5 Plug V-0
350810 5 Cap V-0
350715 6 Plug V-0
350781 6 Cap V-0
350720 9 Plug V-0
350782 9 Cap V-0
350735 12 Plug V-0
350783 12 Cap V-0
350736 15 Plug V-0
350784 15 Cap V-0
Standard Density
Dash Number Color

1-xxxxxx-0 Natural
1-xxxxxx-1 Brown
1-xxxxxx-2 Red
1-xxxxxx-3 Orange
1-xxxxxx-4 Yellow
1-xxxxxx-5 Green
1-xxxxxx-6 Blue
1-xxxxxx-8 Gray
Universal MATE-N-LOK Connectors — Available in Colors
1-xxxxxx-9 Black
* Special for Base

Part Numbers 480763 and
480764
Dash Number Color
xxxxxx-1 Natural
1-xxxxxx-1 Brown
1-xxxxxx-2 Red
1-xxxxxx-3 Orange
1-xxxxxx-4 Yellow
1-xxxxxx-5 Green
1-xxxxxx-6 Blue
1-xxxxxx-8 Gray
1-xxxxxx-9 Black
188
Soft Shell
Universal MATE-N-LOK II Connectors
Product Facts
■ High reliability
■ For use where repair or re-
placement would be difficult
housing
■ Available in 2 through
15 circuit sizes for free-
hanging or panel mount
wire-to-wire connection
■ Mate with standard
Housings and PC Board
Headers
■ Uses standard Universal
MATE-N-LOK panel cutouts
and strain reliefs
■ Polarized housings available
in UL94V-0 flammability
rated material
■ Enclosed contacts for shock
protection
■ F-Crimp terminals accept
30-10 AWG [.05 -5.0 mm2]
wire sizes
■ Contacts available in strip
and loose form Performance Characteristics Technical Documents
The Universal MATE-N-LOK II Product Specification
■ Lanceless contacts for Connector performance characteristics 108-1090 Universal MATE-N-LOK II
tangle-free handling found on pages 189-190 are based on Connectors
■ Insulation capability to free-hanging and panel mount connec- Application Specification
.200 [5.08] diameter tors, loaded with contacts crimped on
Standard Density
stranded wire. 114-1043 Universal MATE-N-LOK II
■ Connector design provides Connectors
for complete contact Instruction Sheet
5.0 KV AC or DC between adjacent
insertion circuits initially 408-3200 Housing, Contacts and
Accessories
■ Three-point stabilization pre- Insulation Resistance—
cisely controls contact align- 1000 megohms minimum between
ment, minimizing stubbing adjacent circuits
■ Tin or duplex gold plated Voltage Rating—600 V AC or DC
contacts Connector Mating—

■ Contacts are on .250 [6.35] Split Pin — 1.5 lb. max. per circuit
centerline spacing Connector Unmating—
Split Pin — .5 lb. min. per circuit
Contact Insertion Force—3.0 lb.
■ Recognized under the max. per contact unassembled
Component
Contact Retention—35 lb. min. per
Program of R
contact
Inc., File No. E28476 Durability—50 cycles, mating and
unmating
■ Certified by Canadian
Standards Association,
R
File No. LR 7189

their Registration Number
3980/Continuous
Surveillance
189
Soft Shell
Universal MATE-N-LOK II Connectors (Continued)
Wire-to-Wire
rent rating of Universal MATE-N-LOK II Calculated Current Table
operating temperature of the housings Circuits 10 12 14 16 18 20 22 24 26 30
which is 120°C including the tempera- 2 19.00 18.00 17.00 14.50 13.00 10.00 8.00 6.50 5.50 3.50
ture rise of the contacts which is a maxi- 3 17.50 16.50 15.50 13.00 12.00 9.00 7.50 6.00 5.00 3.00
mum of 30°C. There are several 4 16.50 15.50 15.00 12.50 11.00 8.50 7.00 5.50 4.50 3.00
variables which have a direct effect on
5 16.00 15.00 14.00 12.00 10.50 8.00 6.50 5.50 4.50 3.00
this maximum current-carrying capabil-
6 Matrix 15.00 14.00 13.00 11.00 9.50 7.50 6.00 5.00 4.00 2.50
ity for a given connector and must be
considered for each application. These 8 14.50 14.00 13.00 10.50 9.50 7.50 6.00 5.00 4.00 2.50
variables are: 9 13.50 12.50 11.50 9.50 8.50 6.50 5.50 4.50 3.50 2.00
10 14.00 13.00 12.50 10.00 9.00 7.00 5.50 4.50 3.50 2.50
12 12.50 12.00 11.00 9.00 8.00 6.00 5.00 4.00 3.00 2.00
internal resistance to current flow and 15 12.00 11.50 10.00 8.50 7.50 6.00 4.50 4.00 3.00 2.00
thus generates less heat. Longer wire Values are based on initial Temperature Rise versus Current Testing and are intended to be a guide in the selection
lengths also enhance current carrying of a connector family. All applications should be tested by the end user. The values listed are per circuit for fully
capabilities since the wire conducts heat loaded housings being 100% energized. Note: All combinations were not tested, and this chart contains interpolated
away from the connector. and extrapolated values.

can be carried. Minimum Wire Lengths for T-Rise vs. Current Testing
Ambient Temperature—The higher AWG Min. Length (in.) AWG Min. Length (in.)
the ambient temperature, the less current 30 2.6 18 9.4
26 4.1 14 13.7
24 5.1 12 16.4
Universal MATE-N-LOK II connectors 20 7.8 10 19.3
also will withstand the following tests:
Note: If wire lengths used are less than those listed above, the current carry-
Vibration—10-55-10 cycles per ing ability of the system will be reduced due to less heat being conducted
minute at .06 inch total excursion away from the connector. The customer should fully test all applications.
Physical Shock—18 drops,
50 g sawtooth at 10 milliseconds
Housing Panel Retention—75 lb. min. Wire-to-Board
Standard Density
Housing Lock Strength—35 lb. min. Due to the vast differences in trace geometry and printed circuit board configurations, we are unable to provide a
Thermal Shock— -55°C to +85°C separate current carrying chart for our printed circuit board header products. However, the above Wire-to-Wire charts
may be used as a guideline for headers if the trace width and thickness is equal to the listed wire gauge. For vertical
Temperature-Humidity Cycling— headers, only 95% of the Wire-to-Wire value should be used. For right-angle headers, only 75% of the Wire-to-Wire
25°C to 65°C at 95 RH value should be used. The chart values are only a tool for connector selection and will require the customer to fully
test their application.
Corrosion—48 hr. at 5% salt
concentration Termination Resistance/Contact Crimp Tensile Force
Termination Contact
Resistance Crimp
Test Resistance

Product Specification (Amps) (Max. Init.) lbs. N
108-1090 Universal MATE-N-LOK II 30 .05 — — 1.5 7
Connectors 28 .08 — — 3 13
26 .12 — — 5 22
24 .2 1.5 3.50 7 31
22 .3 3 3.50 12 53
20 .5 4.5 3.00 17 66
18 .8 6 3.00 30 133
16 1.2 8 2.75 45 200
14 2.0 10 2.75 50 222
12 3.0 — — 60 267
10 5.0 — — 70 311
Note: This is the total resistance between wire crimps of a mated pin and
socket.
190
Soft Shell
Universal MATE-N-LOK II Connector Mating Combinations

PC Board Headers
Number Plug Kit Cap Kit Vertical Pin2 Vertical Socket2 Right-Angle2
of Flammability Style Part Part
Rating Plating Standard Standard
Circuits Number2 Number2 Standard Tail Long Standard Tail Long
Tail Tail Tail Tail Pin Socket
Polarized Polarized
Pre-tin 350786-1 641964-1 350787-1 350824-1 643412-1 350831-1 1-350942-0 643226-1
2 UL94V-0 In-Line 770017-1 770024-1
Duplex1 350786-3 641964-3 350787-3 350824-4 643412-3 — 3-350942-0 —
Pre-tin 350789-1 641966-1 350790-1 350825-1 643414-1 350832-1 1-350943-0 643228-1
3 UL94V-0 In-Line 770018-1 770025-1
Duplex1 350789-3 — 350790-3 350825-4 643414-3 350832-4 3-350943-0 3-643228-0
Pre-tin 350792-1 641968-1 350793-1 350826-1 643416-1 350833-1 1-350944-0 643230-1
4 UL94V-0 In-Line 770019-1 770026-1
Duplex1 350792-3 — 350793-3 350826-4 — 350833-4 3-350944-0 3-643230-0
Pre-tin 640900-1 643406-1 — 640901-1 — — 1-350945-0 643232-1
5 UL94V-0 In-Line 770016-1 —
Duplex1 640900-3 — — 640901-3 — — 3-350945-0 3-643232-0
Pre-tin 350711-1 641970-1 350732-1 350827-1 643424-1 350834-1 — —
6 UL94V-0 Matrix 770020-1 770027-1
Duplex1 350711-4 641970-3 350732-4 350827-4 643424-3 350834-4 — —
Pre-tin 350712-1 641972-1 350742-1 350828-1 643426-1 350835-1 — —
9 UL94V-0 Matrix 770021-1 770028-1
Duplex1 350712-4 641972-3 350742-4 350828-4 643426-3 350835-4 — —
Pre-tin 350713-1 641974-1 350737-1 350829-1 643428-1 350836-1 — —
12 UL94V-0 Matrix 770022-1 770029-1
Duplex1 350713-4 641974-3 350737-4 350829-4 — 350836-4 — —
Pre-tin 350714-1 641976-1 350738-1 350830-1 643430-1 350837-1 — —
15 UL94V-0 Matrix 770023-1 770030-1
Duplex1 350714-4 641976-4 350738-4 350830-4 — 350837-4 — —
1Duplex Finish — Plated with .000030 [.000762] min. gold in mating area, matte tin on solder tail end over .000050 [.00127] min. nickel underplate
on entire contact.
2Universal MATE-N-LOK II Plug and Cap housings accept pin or socket contacts. Use the appropriate contacts in the Plug housing as required by the
mating component.
Standard Density
191
Soft Shell
Contacts Related Product Data

Split pin diameter .086 [2.18] Product Specification
Stock thickness .012 [.305] 108-1090 Universal MATE-N-LOK II Connectors
These contacts can be used in either Application Specification
Universal MATE-N-LOK II Plug or Cap 114-1043 Universal MATE-N-LOK II Contacts
housings. L L
Performance Characteristics— pages 189-190
Housings— pages 193-194
Technical Documents— pages 189 and 205-206 Pin Socket
Contact Part Numbers

Wire Size L Dim. HDM
Ins. Dia. Pin Socket Hand Tool
Range Material & Finish Applicator
AWG [mm2] Range Pin Socket Strip Loose Strip Loose Part No. Part No.
Form Piece Form Piece
30 -26 .032 -.057 1.005 .980 567252-16
[.05 -.12] .813 -1.45 25.53 24.90 Phos. Brz. Gold1 770011-6 770512-6 770012-6 770416-6 567252-46 58439-1
Brass. Pre-tin 770009-1 770252-1 — —
24 -18 .040 -100 1.005 .980 Brass. Duplex2 1-770009-0 1-770252-0 — — 567214-16
[.2 -.8] 1.02 -2.54 25.53 24.90 567214-26 91510-1
Phos. Brz. Pre-tin — — 770010-3 770253-3 567214-46
Phos. Brz. Duplex2 — — 1-770010-0 1-770253-0
Brass. Pre-tin 770007-1 770250-1 — —
.060 -.130 1.005 .980 Brass. Duplex2 1-770007-0 1-770250-0 — — 567213-16
1.52 -3.30 25.53 24.90 567213-26 91500-1
Phos. Brz. Pre-tin — — 770008-3 770251-3 567213-46
20 -14 Phos. Brz. Duplex2 — — 1-770008-0 1-770251-0
[.5 -2.0] Brass. Pre-tin 770005-1 770248-1 — —
.130 -.200 .995 .970 Brass. Duplex2 1-770005-0 1-770248-0 — — 567212-16 91508-14
3.30 -5.08 25.27 24.63 567212-26
Phos. Brz. Pre-tin 770005-3 — 770006-3 770249-3 91506-14
567212-46
Phos. Brz. Duplex2 1-770005-1 — 1-770006-0 1-770249-0
Phos. Brz. Pre-tin 770003-3 770246-3 770004-3 770247-3 567211-16
12 -10 .200 max.3 1.005 .980 567211-26 69710-1 5
[3.0 -5.0] 5.08 25.53 24.90 Phos. Brz. Duplex2 1-770003-0 1-770246-0 1-770004-0 1-770247-0 567211-46
2Duplex Finish — Plated with .000030 [.000762] min. gold in mating area and .000050 [.00127] min. tin in crimp area over .000050 [.00127] min. nickel
underplate on entire contact.
3There is no insulation barrel on this contact. Insulation maximum diameter is limited by the housing. Use of strain relief is recommended with these contacts.
4Use Hand Tool No. 91508-1 for 20 – 18 AWG and No. 91506-1 for 16 – 14 AWG.
5Hand Tool No. 69710-1 uses die set No. 58380-1 for 12 AWG and No. 58380-2 for 10 AWG.
Standard Density
Machine, -4 is used on AMP-O-LECTRIC Model G Machine. See pages 207-210 for further information.
Grounding Pin
current)
Solid pin diameter .084 [2.13] L
.100 [2.54] longer than standard pin Wire Size HDM

Ins. Dia. L Contact Part Numbers Hand Tool
Stock thickness .012 [.304] Range Material & Finish Applicator
Range Dim. Strip Form Loose Piece Part No.
AWG [mm2] Part No.
These contacts can be used in either 567213-13
Universal MATE-N-LOK II Plug or Cap .060 -.130 1.105 Brass. Pre-tin 770193-1 770254-1
1.52-3.30 25.53 567213-23 91500-1
Brass. Duplex1 1-770193-0 1-770254-0
housings only. 20 -14 567213-43

[.5 -2.0] 567212-13
.130-.200 1.085 Brass. Pre-tin 770194-1 770255-1 91508-12
567212-23
3.30-5.08 27.56 Brass. Duplex1 1-770194-0 1-770255-0 567212-43 91506-12
1Duplex Finish — Plated with .000030 [.000762] min. gold in mating area and .000050 [.00127] min. tin in crimp area
over .000050 [.00127] min. nickel underplate on entire contact.
2Use Hand Tool No. 91508-1 for 20 –18 AWG and No. 91506-1 for 16 –14 AWG.
3HDM Applicator part number ending in -1 is used on AMPOMATOR CLS Machine with T or G Terminators, -2 is used
on AMP-O-LECTRIC Model K Machine, -4 is used on AMP-O-LECTRIC Model G Machine. See pages 207-210 for
further information.
Latch Disengaging Tool

Contact Extraction Tool Contact Insertion Tool
Part No. 58382-1
(For extracting contacts crimped (For inserting contacts applied to small diameter wire)
IS 408-9436
on 24 AWG or smaller wire) Part No. 91002-1
Part No. 318851-1 IS 408-7347
Note: All part numbers are RoHS Compliant. IS 408-4371
192
Soft Shell
Housing Kits 2 Circuit, In-line

.250 [6.35] Centerline spacing .550
.550
[13.97]
[13.97]
Material — Nylon
Flammability Rating — UL 94V-0 .845
.580
[14.73] [21.46]
Max. .300 .905
[7.62] [22.98]
Plug Rear Plug Front
108-1090 Universal MATE-N-LOK II
Connectors
Performance Characteristics— .550 .550
pages 189-190 [13.97] [13.97]
Contacts— page 192
Panel Cutout Recommendations—
page 195
.845
Keying Plug— page 196 .905 .300 [21.46]
.580
[14.73]
Strain Reliefs— page 196 [22.98] [7.62] Max.
Kit Components— page 195
Technical Documents— pages 189 Cap Front Cap Rear
and 205-206
Other Mating Connectors 3, 4 and 5 Circuit,

Universal MATE-N-LOK Housings — In-Line
page 175
Universal MATE-N-LOK Headers —
pages 182-183 and 185
A A
Universal MATE-N-LOK Test
Connectors — page 185
.845
.580 [21.46]
[14.73] Max.
.300 .905
[7.62] [22.98]
Standard Density
A A
.845
.580
[21.46]
.905 .300 [14.73]
Max.
[22.98] [7.62]

Cap Front Cap Rear
Number Kit Part Numbers

of A (Includes Front and Rear)
Circuits Dim.
Plug Cap
2 — 770017-1 770024-1
.800
3 20.32 770018-1 770025-1
1.050
4 26.67 770019-1 770026-1
1.300
5 33.02 770016-14 —
Notes:
1. Kits consist of a front and rear component.
2. Kit components can be purchased separately. Page 195.
3. Packaging: Bulk — 250 each component per poly bag/box.
4. Mates with standard Universal MATE-N-LOK cap housing P/N 350810-1
and 640900-X or 640901-X Vertical headers.
193
Soft Shell
Housing Kits 6 Circuit, Matrix

1.080 .800
Material — Nylon [27.43] [20.32]
Flammability Rating — UL 94V-0
.845 .905
.550 .550
Related Product Data [13.97]
[21.46]
[13.97] [22.99]
Max.
108-1090 Universal MATE-N-LOK II Plug Rear Plug Front
Connectors
pages 189-190
Contacts— page 192 1.020 .800 1.080
Panel Cutout Recommendations— [25.91] [20.32] [27.43]
page 195
Keying Plug— page 196
Strain Reliefs— page 196
Kit Components— page 195 .845
Technical Documents— pages 189 .905 .550 [21.46] .550
[22.99] [13.97] [13.97]
and 205-206 Max.
Cap Front Cap Rear
Other Mating Connectors
Universal MATE-N-LOK Housings — 9, 12 and 15 Circuit,
page 176 Matrix
Universal MATE-N-LOK Headers —
pages 182-183 and 185
Universal MATE-N-LOK Test
Connectors — page 185 1.080 .800
[27.43] [20.32]
.845 A .905
A [21.46] [22.99]
Max.
Standard Density
1.020 .800 1.080

[25.91] [20.32] [27.43]
.905 .845
A A
[22.99] [21.46]
Cap Front Max.
Cap Rear
Number Kit Part Numbers

of A (Includes Front and Rear)
Circuits Dim.
Plug Cap
6 — 770020-1 770027-1
.800
9 20.32 770021-1 770028-1
1.050
12 26.67 770022-1 770029-1
1.300
15 33.02 770023-1 770030-1
Notes:
1. Kits consist of a front and rear component.
2. Kit components can be purchased separately. Page 195.
3. Packaging: Bulk — 250 each component per poly bag/box.

194
Soft Shell
Housing Components
Rear
.250 [6.35] Centerline spacing Housing
Section
Material — Nylon
Front
Housing
Related Product Data Rear Section
Product Specification Housing Front Housing
Section Section
108-1090 Universal MATE-N-LOK II
Connectors Plug Housing Cap Housing
pages 189-190 Kit Component Part Numbers
Contacts— page 192 Number
of Plug Cap
Illustrations and Dimensions— Circuits Kit Front Rear Kit Front Rear
pages 193-194
Panel Cutout Recommendations— 2 770017-1 770031-1 770032-1 770024-1 770045-1 770046-1
page 195 3 770018-1 770033-1 770034-1 770025-1 770047-1 770048-1
Keying Plug— page 196 4 770019-1 770035-1 770036-1 770026-1 770049-1 770050-1
Strain Reliefs— page 196 5 770016-1 770319-1 770320-1 — — —
Technical Documents— pages 189 6 770020-1 770037-1 770038-1 770027-1 770051-1 770052-1
and 205-206 9 770021-1 770039-1 770040-1 770028-1 770053-1 770054-1
12 770022-1 770041-1 770042-1 770029-1 770055-1 770056-1
Other Mating Connectors 15 770023-1 770043-1 770044-1 770030-1 770057-1 770058-1
Universal MATE-N-LOK Connectors —
page 176 Notes:
Universal MATE-N-LOK Headers — 1. Kits consist of a front and rear component.
2. Kit components can be purchased separately.
pages 182-183 and 185
Universal MATE-N-LOK Test Note: All part numbers are RoHS Compliant.
Connectors — page 185
Recommended
Standard Density
.110 Number of Dimensions
D [2.79]
Cap Housing Circuits A B C D E
Panel Cutouts .175 2 .565
14.35
.340
8.63
.095
2.41
.530
13.46
.250
6.35
B [4.45]
View is from cap entry side .815 .340 .095 .530 .250
3 20.70 8.63 2.41 13.46 6.35
Note 3
1.065 .340 .095 .530 .250
Refer to Application Specification 4 27.05 8.63 2.41 13.46 6.35
114-1043 .565 .480 .275 1.030 .250
.100 A 6 14.35 12.19 6.99 26.16 6.35
Note [2.54]
E 2 .815 .480 .275 1.030 .250
9 20.70 12.19 6.99 26.16 6.35

1.065 .480 .275 1.030 .350
12 27.05 12.19 6.99 26.16 8.89
Note 4 .175
C
[4.45] 1.315 .480 .275 1.030 .350
15 33.40 12.19 6.99 26.16 8.89
Notes:
1. Recommended panel thickness — .030-.090 [.762-2.286]. Panel must be punched so that housing enters panel in
same direction as the punch.
2. Optional — Do not remove this material when keying cap housing to panel.
3. Circuit #1 location when using panel keying with 6, 9, 12 and 15 circuit housings.
4. Circuit #1 location when using panel keying with 2, 3, and 4 circuit housings.
195
Soft Shell
Plug or 2, 3, 4, 5, 6, 9, 12 and 15
Cap Housing Circuit (Enclosed)
Strain Reliefs Insert
Note 2
IS 408-3320
Insert
Note 2
Material — Nylon
1.300 1.300
[33.02] [33.02]
A A
2 Req’d/Assy.
2 Req’d/Assy.
Note 3
(2) #6x3/8 Lg. Type B Note 3 (2) #6x3/8 Lg. Type B
Pan head sheet metal Pan head sheet metal
screws (not supplied) screws (not supplied)
In-Line Matrix
Number of A Insert Single Wire Wire Bundle Strain Relief

Style Circuits Dim. Supplied Dia. Range Dia. Range Part Numbers
.040 – .190
Yes — 640713-1
.960 1.02 – 4.83
2 24.38 .200 – .350
No — 5.08 – 8.89 640713-2
.040 – .190
Yes — 640714-1
1.140 1.02 – 4.83
3 28.96 .200 – .350
No — 641945-1
In-Line 5.08 – 8.89
.040 – .190
Yes — 641776-1
1.340 1.02 – 4.83
4 34.04 .200 – .350
No — 5.08 – 8.89 641776-2
.040 – .190
Yes — 643030-1
1.530 1.02 – 4.83
5 38.86 .200 – .350
No — 5.08 – 8.89 643030-4
1.030 .120 – .650
6 Yes — 640715-1
Standard Density
26.16 3.05 – 16.51

1.030 .120 – .650
9 26.16 Yes — 3.05 – 16.51 640716-1
Matrix
1.280 .150 – .750
12 32.51 Yes — 3.81 – 19.05 640717-1
1.530 .200 – .850
15 38.86 Yes — 5.08 – 21.59 640718-1
Notes:
1. Insert comes attached to strain relief. It can be used to provide additional adjustment for small wire bundles or discarded.
2. Insert to be positioned as shown by dotted lines.
3. Strain relief part number represents one-half of a strain relief. Two of a part number are required for one connector.
Keying Plug .940

.130 [23.88]
IS 408-3200 [3.30]

Housings— pages 193-194
Technical Documents— pages 189 Part Number
and 205-206 UL94V-0 Nylon material — 770377-1
196
Soft Shell
Universal MATE-N-LOK Headers for UMNL II Connectors
PC Board Vertical 2, 3, 4 and 5 Polarizing

feature
Pin Headers Circuit, In-Line
.175 Standard Tail

.300
Material [4.45]
[7.62]
.235 Long Tail .550
Housing — Nylon [5.97] [13.97]

Contacts — Phosphor bronze Mates with Plug
Pin Header Part Numbers Housing Part Number
Solder tail diameter .062 [1.57] Number of A Pin (Using Socket Contacts)
Circuits Dim. Finish Standard Standard Tail Long Tail3
Tail2 Polarized2 Universal Universal
MATE-N-LOK II MATE-N-LOK
Related Product Data Pre-tin 350786-1
641964-1
350787-1
.550
2 1-641964-14 770017-1 350777-1
Product Specification 13.97
Duplex1 350786-3 641964-3 350787-3
641966-1
PC Board Headers .800 Pre-tin 350789-1 350790-1
3 1-641966-14 770018-1 350766-1
Performance Characteristics— 20.32
Duplex1 350789-3 — 350790-3
pages 189-190 Pre-tin 350792-1 641968-1 350793-1
1.050
Recommended PC Board Hole 4
26.67
770019-1 350779-1
Duplex1 350792-3 — 350793-3
Layout— page 199
Technical Documents— pages 189 1.300 Pre-tin 640900-1 643406-1 —
5 770016-1 350809-1
33.02 Duplex1 640900-3 — —
and 205-206
Mating Connectors [.00127] min. nickel underplate on entire contact.
2Use Standard Tail for .062 [1.57] thick PC Board.
Universal MATE-N-LOK II 3Use Long Tail for .125 [3.18] thick PC Board.
Plug Housings — pages 193-194 4Black in color.
feature
Circuit, Matrix
.175 Standard Tail
Standard Density
[4.45] .800
.235 Long Tail .550 [20.32]
[5.97] [13.97]
Mates with Plug

Pin Header Part Numbers Housing Part Number
Number of A Pin (Using Socket Contacts)
.550 Pre-tin 350711-1 641970-1 350732-1
6 770020-1 350715-1
13.97 Duplex1 350711-4 641970-3 350732-4

Universal MATE-N-LOK Headers
641972-1
.800 Pre-tin 350712-1 350742-1
9 1-641972-14 770021-1 350720-1
20.32
Duplex1 350712-4 641972-3 350742-4
641974-1
1.050 Pre-tin 350713-1 350737-1
12 1-641974-14 770022-1 350735-1
26.67
Duplex1 350713-4 641974-3 350737-4
1.300 Pre-tin 350714-1 641976-1 350738-1
15 770023-1 350736-1
33.02 Duplex1 350714-4 641976-4 350738-4
3Use Long Tail for .125 [3.18] thick PC Board.
4Black in color.
197
Soft Shell
Universal MATE-N-LOK Headers for UMNL II Connectors (Continued)
PC Board Vertical 2, 3, 4 and 5

Socket Headers Circuit, In-Line Polarizing
feature
Material .175 Standard Tail

[4.45] .300
Housing — Nylon [7.62]
.235 Long Tail .550
Flammability Rating — UL94V-0 [5.97] [13.97]
Contacts — Phosphor bronze

Mates with Plug
Solder tail diameter .062 [1.57] Socket Header Part Numbers Housing Part Number
Number of A Socket (Using Pin Contacts)
Related Product Data MATE-N-LOK II MATE-N-LOK
.550 Pre-tin 350824-1 643412-1 350831-1
Product Specification 2
13.97
770017-1 350777-1
Duplex1 350824-4 643412-3 —
.800 Pre-tin 350825-1 643414-1 350832-1
PC Board Headers 3
20.32
770018-1 350766-1
Duplex1 350825-4 643414-3 350832-4
Performance Characteristics— 1.050 Pre-tin 350826-1 643416-1 350833-1
pages 189-190 4 770019-1 350779-1
26.67 Duplex1 350826-4 — 350833-4
Recommended PC Board Hole
1.300 Pre-tin 640901-1 — —
Layout— page 199 5
33.02
770016-1 350809-1
Duplex1 640901-3 — —
and 205-206 1Duplex Finish — Plated with .000030 [.000762] min. gold in mating area, matte tin on solder tail end over .000050
Mating Connectors 3Use Long Tail for .125 [3.18] thick PC Board.
feature
Circuit, Matrix
Standard Density
.175 Standard Tail

.800
[4.45]
[20.32]
.235 Long Tail .550
[5.97] [13.97]
Mates with Plug

Socket Header Part Numbers Housing Part Number
Number of A Socket (Using Pin Contacts)
.550 Pre-tin 350827-1 643424-1 350834-1
6 770020-1 350715-1
13.97 Duplex1 350827-4 643424-3 350834-4
.800 Pre-tin 350828-1 643426-1 350835-1

9 770021-1 350720-1
20.32 Duplex1 350828-4 643426-3 350835-4
1.050 Pre-tin 350829-1 643428-1 350836-1
12 770022-1 350735-1
26.67 Duplex1 350829-4 — 350836-4
1.300 Pre-tin 350830-1 643430-1 350837-1
15 770023-1 350736-1
33.02 Duplex1 350830-4 — 350837-4
3Use Long Tail for .125 [3.18] thick PC Board.
198
Soft Shell
Recommended 2, 3, 4 and 5 .175 .250

Typ.
[4.45] [6.35]
PC Board Circuit, In-Line .070
Dia. Typ.
[1.78]
Hole Layouts
Polarizing Hole
for Pin and Socket See Note
Vertical Headers No. 1 Position
2 Circuit
Related Product Data 3 Circuit
4 Circuit
Vertical Headers — pages 197-198
5 Circuit
Polarizing Hole
Polarizing Hole See Note
See Note .250 .175
Typ.
.250 .175 [6.35] [4.45]
Typ.
[6.35] [4.45] No. 2 Circuit
6, 9, 12 and 15 No. 2 Circuit
Circuit, Matrix .250 .250
Typ. No. 1 Circuit
Typ. [6.35]
[6.35] No. 1 Circuit
.070 Dia. Typ.
.070 Dia. Typ. [1.78]
[1.78]
.250 .175 .250 .175

Typ. Typ.
[6.35] [4.45] [6.35] [4.45]
Polarizing Hole Polarizing Hole

See Note See Note
No. 2 Circuit No. 2 Circuit
250 .250
Typ. Typ.
.35] .070 No. 1 Circuit [6.35] .070 No. 1 Circuit
Dia. Typ. Dia. Typ.
[1.78] [1.78]
Note: Polarizing hole .070 [1.78] Dia. required for polarized headers only.
PC Board Vertical
.250
Pin Headers with [6.35]
ACTION PIN Contacts A
Material and Finish
Standard Density
Housing — PBT, black .299 .200 ± .004 Typ. .630
[7.59] Max.
Flammability Rating — UL94V-0 [5.08 ± 0.10] [16.00]
Contacts — Copper alloy, plated with

tin over nickel on entire contact Mates with Plug Housing
Number of Part Number (Using Socket Contacts)
Circuits A Dim. Part Number
Universal Universal
.750
2 173924-1* 770017-1 350777-1
Performance Characteristics— 19.05
pages 189-190 3 1.000 173925-1* 770018-1 350766-1
Technical Documents— pages 189 25.40

and 205-206 4 1.250 173926-1* 770019-1 350779-1
31.75
*Install in PC Board with arbor tool.
108-5222 ACTION PIN Universal
MATE-N-LOK Header Note: All part numbers are RoHS Compliant.
Assembly .062 Ref.
[1.57]
4 Circuit
Mating Connectors
3 Circuit
Universal MATE-N-LOK II 2 Circuit
Dia. After
Universal MATE-N-LOK Reflow
Plug Housings — page 175 .100 ± .004
.032 ± .002 .001-.003
[0.81 ± 0.05] [0.03-0.08]
[2.54 ± 0.10]
.200 ± .004 .038 ± .001
[5.08 ± 0.10] .0003-.0012
[0.97 ± 0.03 ] [0.01-0.03]
Recommended PC Board Hole Layout PC Board Hole Dimensions
199
Soft Shell
PC Board Right-Angle 2, 3, 4 and 5 Circuit, In-line

Pin and Socket Headers
.505
.250 [6.35] Centerline spacing [12.83]
.150
Dia.
.060 Dia. Typ. [3.81]
[1.52] 2 Places
.680
Material [17.27]
Housing — Nylon .100
.250 [2.54]
Flammability Rating — UL 94V-0 No. 1 Circuit [6.35]
Contacts — Phosphor bronze .250
.290 Typ.
Typ. [7.37]
Solder tail width .052 [1.32] [6.35]
Use 6-32 UNC Pan Head Screw

3/8 [9.53] long for mounting
Related Product Data (Not Supplied)
Product Specification .360 Recommended PC Board Hole Layout

.160
[9.14] .062 [1.57] Board Thickness
108-1053 Universal MATE-N-LOK [4.06]
PC Board Headers
Part Numbers
Performance Characteristics— Dimensions
Number of Contact Right-Angle Header Mates with Plug Housing
pages 189-190 Circuits A B C Finish Universal Universal
Technical Documents— pages 189 Pin Socket MATE-N-LOK II MATE-N-LOK
and 205-206
.550 1.245 .830 Pre-tin 1-350942-0 643226-1
2 770017-1 350777-1
13.97 31.62 21.08 Duplex1 3-350942-0 —
Mating Connectors
.800 1.495 1.080 Pre-tin 1-350943-0 643228-1
Universal MATE-N-LOK II 3 770018-1 350766-1
20.32 37.97 27.43 Duplex1 3-350943-0 3-643228-0
1.050 1.745 1.330 Pre-tin 1-350944-0 643230-1
4 770019-1 350779-1
Universal MATE-N-LOK 26.67 44.32 33.78 Duplex1 3-350944-0 3-643230-0
Plug Housings — page 175 1.300 1.995 1.580 Pre-tin 1-350945-0 643232-1
5 770016-1 350809-1
33.02 50.67 40.13 Duplex1 3-350945-0 3-643232-0
Standard Density
200
Soft Shell
High Current Contacts

The Louvertac bands have the versatility
of being designed into contact dimen-
sions used in existing AMP connectors. Plug
Part No. 770020-1
Universal MATE-N-LOK II High Current
contacts have been designed to fit into
an existing Universal MATE-N-LOK II
housing. An initial T-Rise test of a
fully energized 4 circuit connector with
10 gage wires has shown a 31 amp Cap
Part No. 770027-1
capability per line with a 30° T-rise.
Cable-to-Cable
Material Contacts
Body — Copper Alloy Contact Part Numbers
Wire Size Crimp Tools
Louvertac Band — Beryllium Copper AWG Pin Socket
Finish — Silver 10 193796-1 193797-1 Daniels
Contact Extraction Tool No. 318851-1 Hand Tool #M310 or AMP P/N 356114-1
12-14 193841-1 193842-1 Positioner #TP1013 or AMP P/N 356337-1
Latch Disengaging Tool No. 58382-1
Note: High Current contacts are not intermateable with any other Universal MATE-N-LOK contact.
Component Program of Standard
MATE-N-LOK II Pin
Underwriters
Laboratories Inc.,
R
Connector Housings
File No. E28476 Standard No. of Kit Part Numbers
MATE-N-LOK II CircuIts Plug Cap
■ Certified by Canadian Socket
Standards 2 770017-1 770024-1
R
Association, 3 770018-1 770025-1

File No. LR7189 4 770019-1 770026-1
5 770016-1 —
■ Passed test by VDE under 6 770020-1 770027-1
their Registration Number 9 770021-1 770028-1
3980/Continuous High Current Socket 12 770022-1 770029-1
Surveillance Part No. 193797-1 15 770023-1 770030-1
Design Objective —108-1583
Standard Density
Application Specification—
114-16021 High Current Pin
Part No. 193796-1
Cable-to-Right-Angle Board
Right-Angle Receptacle
Material Part No. 193839-3
Housing — UL 94V-0 Nylon Plug
Part No. 770019-1
Contact Body — Copper Alloy
Louvertac Band — Beryllium Copper

Finish — Silver

Component Program of Connector Housings
Underwriters R
No. of Part Numbers
Laboratories Inc., CircuIts Socket Header Mates with Plug Housing
File No. E28476
2 193839-1 770017-1
■ Certified by Canadian 3 193839-2 770018-1
Standards R 4 193839-3 770019-1
Association, 5 193839-4 770016-1
File No. LR7189
■ Passed test by VDE under Notes: 1. High Current contacts with Louvertac bands are not intermateable with any other contact.
their Registration Number 2. Additional information on connectors is available in AMP High Current Products Catalog 65141.
3. Additional information on contacts is available in AMP Precision Pin and Socket Contacts
3980/Continuous Catalog 65910.
Surveillance
Design Objective —108-1594 Note: All part numbers are RoHS Compliant.
201
Soft Shell
High Current .35 .55

.80
[20.32]
.55
[13.97]
Vertical Pin Headers [8.89] [13.97]
.250 .250
Typ. Typ.
High Current Universal MATE-N-LOK II [6.35] [6.35]
Vertical Pin Headers are designed to
accept Universal MATE-N-LOK II Plugs .55 .55
[13.97] [13.97]
with High Current Socket contacts. All
housings are polarized in order to allow
proper circuit board placement. Eight .03 .03
versions are available from 2 circuit to [.76] [.76]
.17 .17
15 circuits. [4.32]
[4.32]
2 Circuit 6 Circuit
Material Part No. 194009-1 Part No. 194002-1
Housing — UL 94V-0 Nylon
.80 .55
Contacts — Copper Alloy .30 .55 [20.32] [13.97]
[7.62] [13.97]
Finish — Silver .25
Typ. .25
Typ.
[6.35] [6.35]

.80 .80
Component Program of [20.32] [20.32]
Underwriters R
Laboratories Inc.,
File No. E28476
.03 .03
■ Certified by Canadian [.76]
.17
[.76]
.17
Standards R [4.32] [4.32]
Association, 3 Circuit 9 Circuit
File No. LR7189 Part No. 194017-1 Part No. 194012-1
.80 .55
their Registration Number .30 .55
[20.32] [13.97]
[7.62] [13.97]
3980/Continuous .25
Typ. .25
Typ.
Surveillance [6.35] [6.35]
Design Objective —108-1594
1.05 1.05
[26.67] [26.67]
Standard Density
.03 .03
[.76] [.76]
.17 .17
[4.32] [4.32]
4 Circuit 12 Circuit
Part No. 194010-1 Part No. 194014-1
.80 .55
.30 .55 [20.32] [13.97]
[7.62] [13.97]
.25 .25
Typ. Typ.
[6.35] [6.35]
1.30 1.30
[33.02] [33.02]
.03 .03
[.76] [.76]
.17 .17
[4.32] [4.32]
5 Circuit 15 Circuit
Part No. 194018-1 Part No. 194013-1
Notes: 1. High Current contacts with Louvertac bands are not intermateable with any other contact.
2. Additional information on connectors is available in AMP High Current Products Catalog 65141.
202
Soft Shell
.156 MATE-N-LOK Connectors
Product Facts
■ Positive polarized nylon
housings
■ Panel mount or free-hanging
■ Numbered cavities for easy
circuit identification
■ Removable, crimp snap-in
contacts
■ Contacts accept 20-10 AWG
wire sizes
■ Pin contacts are used in cap
housings, socket contacts
are used in plug housings
Component
Program of R
■ Certified by Canadian
Standards Association File
No. LR7189
.925
[2.35] .760
[1.93]
Pin Socket
Used in Caps Used in Plugs
Standard Density
Contacts Wire Size Contact Part Number HDM1
Ins. Dia. Hand Tool
Pin diameter .156 [3.96] Range Pin Socket Applicator
Range Part No.
AWG [mm2] Strip Form Loose Piece Strip Form Loose Piece Part No.
Material and Finish 20-14

466462-1
.125 max. 61086-1 61251-1 61085-1 61250-1 466462-2 58631-1
Contacts— [.5-2.0] 466462-3
Brass, Pre-tin plated 12-10 687765-2
[3.0-6.0] .185 max. 61234-1 61253-1 61233-1 61252-1 687765-3 58632-1
1To be used with appropriate application machine. See pages 201-204 for further information.
Note: All part numbers are RoHS Compliant. .390 [9.91] Centerline
Insertion Tool Extraction Tool

Part No. 91002-1 Part No. 691458-1 (Pins)
(IS 408-7347) Part No. 691458-2 (Sockets)
(IS 408-4322)
203
Soft Shell
.156 MATE-N-LOK Connectors (Continued)
Housings 1.220 1.220

Free-Hanging or Panel Mount [30.99] [30.99]

Contacts—page 203 A A
Product Specification .390 .390
[9.91] [9.91]
108-8002
.430 .430
114-1109 [10.92] [10.92]
Pin Housing (Cap) Pin Housing (Cap)

Material Free-Hanging Panel Mount
Part Number 794117-1 Part Number 794118-1
Housings—
Nylon, Natural Color 1.17
Flammability Rating—UL94V-2 [29.72]
.480 .450
.370
[12.19]
A .180 [9.40] [11.43]
.390 [4.57] Ref.
[9.91]
.460
R .225 1.91
[11.68] .430 .210
[5.72] [48.51]
1.020 [10.92] Ref. [5.33]
4 Plc.
[25.91]
Socket Housing (Plug) Panel Mount Cutout
Part Number 794116-1
Note: Panel must be punched in the same
direction as the housing will be inserted.
Number of A Cap
Plug
Circuits Dim. Free-Hanging Panel Mount
.048
3 1.210 794412-1 794413-1 —
.063
4 1.590 794116-1 794117-1 794118-1

Standard Density
204
Soft Shell
Technical Documents
Related Product Data Various technical documents are available for your use:
Product Specifications describe technical performance characteristics and verification tests.
Connectors They are intended for the Design, Component and Quality Engineer.
2.5 mm Signal Double Lock (SDL)— 108-1000 Commercial MATE-N-LOK Connectors
pages 9-16 108-1022 (MR) Miniature Rectangular Connectors
Technical Documents
Micro MATE-N-LOK 3 mm— 108-1031 Universal MATE-N-LOK Connectors
pages 17-47 108-1031-1 Splash Proof Seal, Universal MATE-N-LOK Connectors
Grace Inertia Connectors 108-1032 .140 Diameter MATE-N-LOK Pin and Socket Connectors
(GIC) 3.5—pages 49-52 108-1037 .062 Commercial Pin and Socket Connectors
.062 Commercial Pin and 108-1037-1 .062 Commercial Pin and Socket Contacts
Socket—pages 53-57 108-1038 .093 Commercial Pin and Socket Connector
Power Double Lock (PDL)— 108-1053 Universal MATE-N-LOK Printed Circuit Board Headers
pages 59-81
108-1077 Commercial MATE-N-LOK Printed Circuit Board Headers
Mini Universal MATE-N-LOK— 108-1078 (MR) Miniature Rectangular Printed Circuit Board Headers
pages 83-94
108-1090 Universal MATE-N-LOK II Connectors
Mini Universal MATE-N-LOK 2— 108-1542 Mini-Universal MATE-N-LOK Connectors
pages 99-107
108-1542-2 Splash Proof Seals for Mini-Universal MATE-N-LOK Connectors
(MR) Miniature Rectangular—
108-1543 Mini-Universal MATE-N-LOK Headers
pages 109-118
108-1594 Universal MATE-N-LOK Headers with High Current Contacts
VAL-U-LOK Connector System—
pages 119-124 108-1693 Mini-Universal MATE-N-LOK II Connectors
108-1694 Mini-Universal MATE-N-LOK II Headers
AMP-DUAC—pages 125-133
108-1699 AMP-DUAC Headers
108-1836 Micro MATE-N-LOK 3 mm Connectors
(PKC)—pages 135-141
108-2069 Universal MATE-N-LOK Circular Connector
.093 Commercial Pin and
Socket—pages 143-149 108-5138 Mini-Universal MATE-N-LOK Connectors (UL 94V-0)
108-5151 Mini-Universal MATE-N-LOK Connectors (UL 94V-2)
Commercial MATE-N-LOK—
pages 151-162 108-5155 Commercial MATE-N-LOK Pin Header Assembly
.140 MATE-N-LOK—pages 165-167
108-5222 Universal MATE-N-LOK Headers with ACTION PIN Contacts
108-5410 Power Double Lock (PDL) Connectors
Universal MATE-N-LOK—
pages 169-188 108-5439 Power Double Lock (PDL) Connectors (SMT)
108-5459 2.5 mm Signal Double Lock (SDL) Connectors
Universal MATE-N-LOK II—
pages 189-195 108-5699 5.0 mm Power Key Connectors (PKC)
.156 MATE-N-LOK—pages 203-204
108-5810 Grace Inertia Connectors (GIC) 3.5
108-8002 .156 Diameter MATE-N-LOK Connectors
108-19099 AMP-DUAC Receptacles
108-49000 Commercial MATE-N-LOK IDC Insulation Displacement Connectors
Application Specifications describe requirements for using the product in its intended appli-
cation and/or crimping information. They are intended for the Packaging and Design
Engineer and the Machine Setup Person.
114-1007 .140 Diameter MATE-N-LOK Contacts
114-1010 Universal MATE-N-LOK Connectors
114-1012 Commercial MATE-N-LOK Contacts
114-1013 .062 Commercial Pin and Socket Connectors
114-1014 (MR) Miniature Rectangular Contacts
114-1043 Universal MATE-N-LOK II Connectors (housings, contacts and strain reliefs)
114-1109 .156 Diameter MATE-N-LOK Connectors
114-1111 Mini-Universal MATE-N-LOK 2 Connectors
114-5203 2.5 mm Signal Double Lock (SDL) Connectors
114-5292 5.0 mm Power Key Connectors (PKC)
114-5306 Grace Inertia Connectors (GIC) 3.5
114-6067 AMP-DUAC Crimping Contacts
114-13000 Micro MATE-N-LOK 3 mm Connectors
205
Soft Shell
Technical Documents (Continued)

Application Specifications (Continued)
114-13089 Mini-Universal MATE-N-LOK Sealed Connectors

114-16017 Mini-Universal MATE-N-LOK Connectors
114-19048 AMP-DUAC Receptacles (Use of)
114-49000 .093 Commercial Pin and Socket Connectors
Technical Documents
114-49001 Commercial MATE-N-LOK IDC Insulation Displacement Connectors
Instruction Sheets provide instructions for assembling or applying the product. They are in-
tended for the Manufacturing Assembler or Operator.
408-3186 Terminating Head (PN 231894-1) (Commercial MATE-N-LOK IDC Connector)
408-3200 Universal MATE-N-LOK II Connectors (Housings, Contacts and Accessories)
408-3231 (MR) Miniature Rectangular Connectors (Pin Housing, Socket Housing,
Contacts, and Accessories)
408-3320 Universal MATE-N-LOK Strain Relief Assembly and Keying Plug
408-3392 Universal MATE-N-LOK Splash Proof Seals
408-3393 Mini-Universal MATE-N-LOK 2 Connectors
408-4118 Contact Extraction Tool (PN 189727-1)
408-4322 Contact Extraction Tools [PN 691458-1 (Pins) and 691458-2 (Sockets)]
408-4378 Extraction Tool (PN 318845-1)
408-6790 Hand Tool Handle (PN 58074-1)
408-7158 Contact Extraction Tools [PN 1-305183-1 (Pins) and 1-305183-2 (Sockets)]
408-7166 Commercial MATE-N-LOK Panel Mount Connector
408-7200 Commercial MATE-N-LOK Free-Hanging Connector
408-7201 Commercial MATE-N-LOK Detent Engagement Connectors, 2 and 3 circuit
408-7209 Commercial MATE-N-LOK Commoning Tabs
408-7211 Pin and Socket Extraction Tool (PN 465644-1)
408-7215 Commercial MATE-N-LOK Single Circuit Connector
408-7300 MATE-N-LOK Contact and Housing Selection Charts
408-7347 Contact Insertion Tool (PN 91002-1)
408-7582 Commercial MATE-N-LOK Keying Plug
408-7714 Universal MATE-N-LOK Connectors
408-7763 Power Unit (PN 91112-2)
408-7984 Contact Insertion Tool (PN 455830-1)
408-9330 Head (PN 231920-2) (Used with Arbor Tool PN 91085-2)
408-9436 Latch Disengaging Tool (PN 58382-1)
408-10003 Contact Retention Test Tool (PN 1586700-1)
408-10017 Universal MATE-N-LOK Sealed Bulkhead Connectors
206
Soft Shell
Application Tooling
Semiautomatic Machines AMP 3K/40 and AMP 5K/40 As value oriented terminators,
Terminators the AMP 3K/40 and AMP 5K/40
are designed for customers
that require the increased
AMP-O-LECTRIC Model “G” Semiautomatic bench machines output and quality of a semi-
Terminating Machines, for crimping reeled terminals automatic machine at a com-
354500-1, -9, -11 and contacts, featuring a quiet petitive price. By incorporating
and reliable direct motor drive, the most commonly requested
microprocessor controls for features as standard and
ease of setup and operation, offering a long list of optional
Application Tooling
and guarding and lighting equipment, these terminators
designed for operator conven- offer flexibility to meet the
ience and safety. All models specific needs of various
are equipped with either applications at the lowest
manual or automatic precision possible cost.
adjustment of crimp height.
Machine-mounted sensors are
available for crimp quality
monitoring using conventional
miniature-style applicators.
Optional Stripping Module for the AMP 3K/40, AMP 5K/40
Specifications and AMP-O-LECTRIC Model G Terminators
Width—18.7-25.3 [475-643] depend-
ing on applicator type The combination of the
Depth—21.5-28.1 [546-713] depend- Stripping Module with the
ing on applicator type AMP-O-LECTRIC Model G
Height—20 [508] Terminator or the AMP 3K/40,
Weight—240 lb [110 kg] 5K/40 provides an economical,
Electrical—120 or 220 VAC, 50 or 60 Hz proficient method of stripping
Air—90-110 psi [6.21-7.59 bar], wire and crimping terminals
6 scfm [0.00282 m3/s] when required on the same machine. Wires
with air-feed applicators are stripped moments before
crimping, meaning there is
Wire Range—26-10 AWG [0.12-6
virtually no chance of damag-
mm2] solid or stranded, depending on
ing wire conductors during
product applied
handling or storage. Once the
For more information, request Catalog wire is fed into the start sensor
65828, Catalog 82275 [Crimp the Stripping Module does the
Quality Monitor (CQM)]. rest, improving placement
accuracy.
For more information, request
AMP-O-MATIC Semiautomatic bench crimping Catalog 1309085.
Stripper-Crimper Machine, machines that also strip the
854040-3, -4 wire, and are therefore used for
terminating jacketed cable. Crimp Quality Monitor
Feature manual precision
adjustment of crimp height,
keyed strip blades for faster,
more accurate setups, and an
efficient scrap removal system.
All adjustments can be made
from the front of the machines
without special tools. Available
with crimp quality monitoring.
Specifications This system measures the crimp Crimper Machines, the monitor
Width—14 [355] height of each termination as it is mounted to the machine. For
Depth—18 [457] is made. It also evaluates the use with AMPOMATOR CLS IV+
Height—33 [838] without reel quality of each crimp. If a crimp Machines, it is integrated into
is questionable, the monitor the machine’s operating system,
Weight—150 lb [68 kg]
alerts the operator with both with the displays appearing on
Electrical—120 VAC, 50 or 60 Hz, .5 A visual and audible alarms. It the machine’s touch screen.
Air—80-100 psi [5.52-6.90 bar], 3.5 also features ports for printing
scfm [0.00165 m3/s] For more information, request Catalog
and networking. For use with 82275.
Wire Range—32-14 AWG AMP-O-LECTRIC Model “G”
[0.03-2 mm2] and AMP-O-MATIC Stripper-
For more information, request Catalog
65004.
Note: This listing is for reference purposes only. To obtain part numbers for specific applications call Technical Support.
207
Soft Shell
Application Tooling (Continued)
Automatic Machines
AMPOMATOR System III System III Applicator
Leadmaker
Application Tooling
The System III Applicator set-up information, a precision

The AMPOMATOR System III new technologies in terminal introduces several new fit round ram, and a newly
Leadmaker is designed for feeding and machine set-up technologies into the applicator designed terminal depressor.
the demands of low-volume/ found in the System III including a precision servo- It still utilizes the proven quality
high-mix manufacturing and Applicator to offer significant electric motorized feeding of the HD-M crimper and
precision quality. This lead- advantages for higher through- system, a built-in data module anvil tooling.
maker combines the best wire put and efficiencies. for storing terminal crimp and
processing capabilities with Request Catalog 1654956-5.
AMPOMATOR CLS IV+

Lead-Making Machines,
356500-1, -2 Fully-automatic machines Specifications
that measure, cut, strip
Width—159 [4 039]
and terminate single leads.
Microprocessor-controlled, and Depth—68 [1 730]
programmed and operated Height—90 [2 285] min., with
using an easy-to-follow, menu- 24 [610] dia. reel
driven touchscreen. Features Weight—2 000 lb [907 kg]
include direct-drive terminating Electrical—220 VAC, 50 or 60 Hz,
units with precision crimp height 1 ∅, 20 A with neutral and ground
adjustment, fully programmable Air—90 psi [6.21 bar], 15 scfm
setups, wire runout and splice [0.00708 m3/s] sustained
detection, and motorized Wire Range—26-10 AWG
pre-feed with wire straightener. [0.12-6 mm2] stranded, 26-16 AWG
Crimp quality monitoring is [0.12-1.4 mm2] solid
also available. Lead Lengths—3-90 [76.2-2 286],
90-1 000 [2 286-25 400] with long lead
conveyors
124324.
EDGE Electronic Applicator The new, versatile EDGE appli- limits, operators avoid break-
Counter cator counter tracks wearable downs and rejects caused by
tool usage for the most effec- tool wear or mis-adjustment.
tive maintenance planning. The
completely electronic counter,
1773385.
with clear LCD display, indi-
cates cycles since installation.
By performing maintenance at
measured intervals with pre-set
208
Soft Shell
Applicator Styles End- and Side-Feed Heavy- ■ Handle a wide variety of

Duty Miniature (HDM) products
Applicators ■ Used with both semi- and
fully-automatic machines
■ Quickly interchangeable to
run different products
■ Easily repaired
■ Simple dial-in settings to
handle similar products
Application Tooling
and various wire sizes
Stripper-Crimper (SCA) ■ For use with AMP-O-MATIC Crimp Quality Monitor ■ Same basic features as
Applicators Stripper-Crimper Machines (CQM) Applicators regular HDM and SCA
■ Terminate a wide variety of applicators
open-barrel products ■ Recommended for use
■ Quickly interchangeable to with machines featuring
run different products manual or automatic
■ Easily repaired precision-adjust
■ Simple dial-in settings to ■ Use two built-in sensors to
handle similar products and provide the Crimp Quality
various wire sizes Monitor with data to
■ CQM applicators are measure crimp height,
available and evaluate the quality of
each crimp
Applicator and Hand Tool Applicators Hand Tools

Density Product Line
Selection Guide A B C D E
2.5 mm Signal Double Lock (SDL) * * * X -
Related Product Data Micro MATE-N-LOK 3 mm X X X X -
Contacts Grace Inertia Connectors (GIC) 3.5 * * * X -
2.5 mm Signal Double Lock (SDL)—page 12 .062 Commercial Pin and Socket X X X - X
Power Double Lock (PDL) * * * X -
Micro MATE-N-LOK 3 mm—page 22 High
Mini-Universal MATE-N-LOK X X X X X
Grace Inertia Connectors (GIC) 3.5—page 50
Sealed Mini-Universal MATE-N-LOK X X X X -
.062 Commercial Pin and Socket—page 55
Mini-Universal MATE-N-LOK 2 X X X X X
Power Double Lock (PDL)—page 61 (MR) Miniature Rectangular X X X X -
Mini Universal MATE-N-LOK—page 84 VAL-U-LOK Connector System X - - - X
Mini Universal MATE-N-LOK 2—pages 100-101 AMP-DUAC X X - X -
(MR) Miniature Rectangular—page 112 5.0 mm Power Key Connectors (PKC) * * * X -
VAL-U-LOK Connector System—page 120 .093 Commercial Pin and Socket X X X - X
AMP-DUAC—pages 126-127 Commercial MATE-N-LOK X X X X X
Standard
5.0 mm Power Key Connectors (PKC)—page 137 .140 MATE-N-LOK X X X X -
Universal MATE-N-LOK X X X X X
.093 Commercial Pin and Socket—page 145
Universal MATE-N-LOK II X X X X X
Commercial MATE-N-LOK—pages 155-156
.156 MATE-N-LOK X - - X -
.140 MATE-N-LOK—page 166 A—Heavy Duty Miniature (HDM) Applicators
Universal MATE-N-LOK—pages 172-173 B—Stripper-Crimper Applicators (SCA)
Universal MATE-N-LOK II—page 192 C—Crimp Quality Monitor (CQM) Applicators
D—CERTI-CRIMP Hand Tool
.156 MATE-N-LOK—page 203 E—PRO-CRIMPER III Commercial Hand Tool
* Contact the Tooling Assistance Center (TAC) at 1-800-722-1111 for Applicator Part Numbers.
Mechanical Hand Tools CERTI-CRIMP II Straight Premium grade hand tools. adjustment lever, when
Action Hand Tools (SAHT) Feature ratchet control to applicable. Approximate
91501-1, 91502-1 provide complete crimp weight 1.3 lb [0.59 kg]
cycle. Die sets close in a For more information, request
straight line. Include a con- Catalog 65780.
tact locator and wire stop,
plus an insulation crimp
209
Soft Shell
Hand Tools CERTI-CRIMP II Hand Tool PRO-CRIMPER III Hand Tool
Contacts
2.5 mm Signal Double Lock
(SDL)—page 12
Micro MATE-N-LOK 3 mm—page 22
Application Tooling
Grace Inertia Connectors (GIC)

3.5—page 50
.062 Commercial Pin and Catalog 65780 Catalog 82276
Socket—page 55
Power Double Lock (PDL)—page
Features CERTI-CRIMP Hand Tool PRO-CRIMPER III Hand Tool
61
Field Repair/Prototyping X X
Mini Universal MATE-N-LOK— OEM Applications/Low Volume Production X —
page 86 Ratchet Control X X
Mini Universal MATE-N-LOK 2— Brush/Bellmouth Control X X
pages 100-101 Precision Crimp Height Control X X
(MR) Miniature Rectangular— Little/No Operator Training X —
page 112 Insulation Adjustment X —
VAL-U-LOK Connector System— Repairable X —
page 120
AMP-DUAC—pages 126-127 CERTI-CRIMP Hand Tool PRO-CRIMPER III Hand Tool
5.0 mm Power Key Connectors Density Product Line
Part Number Instruction Sheet Part Number Instruction Sheet
(PKC)—page 137 234603-1 411-5735 — —
2.5 mm Signal Double Lock (SDL)
.093 Commercial Pin and 234604-1 411-5736 — —
Socket—page 145 Micro MATE-N-LOK 3 mm 91501-1 408-8547 — —
91502-1 408-8547 — —
Commercial MATE-N-LOK— Grace Inertia Connectors (GIC) 3.5 1596277-1 411-78101 — —
pages 155-156 — — 90870-1 408-9965
.062 Commercial Pin & Socket
.140 MATE-N-LOK—page 166 — — 90869-1 408-9964
91567-1 408-8547 — —
Universal MATE-N-LOK— Power Double Lock (PDL)
91569-1 408-8547 — —
pages 172-173 91529-1 408-8547 90758-1 408-9938
Mini-Universal MATE-N-LOK
Universal MATE-N-LOK II—page 192 and 91522-1 408-8547 90759-1 408-9962
High 91594-1 408-8547 90760-1 408-9963
.156 MATE-N-LOK—page 203 Sealed Mini-Universal MATE-N-LOK
90717-2 408-4443 — —
91529-1 408-8547 — —
91522-1 408-8547 — —
Mini-Universal MATE-N-LOK 2 91594-1 408-8547 — —
90717-2 408-4443 — —
91534-1 408-8547 58514-1 408-9973
(MR) Miniature Rectangular
91526-1 408-8547 58514-1 408-9973
— — 91387-1 408-8917
VAL-U-LOK Connector System
— — 91388-1 408-8918
90714-1 408-4385 — —
AMP-DUAC
734202-2 — — —
5.0 mm Power Key Connectors (PKC) — — — —
— — 90872-1 408-9967
.093 Commercial Pin & Socket
— — 90871-1 408-9966
91515-1 408-8547 — —
Commercial MATE-N-LOK 91512-1 408-8547 90574-1 408-9886
91504-1 408-8547 90575-1 408-9887
91552-1 408-8547 — —
69710-11 408-2095 — —
.140 MATE-N-LOK
58373-12 408-9442 — —
Standard 58374-12 408-9442 — —
58439-1 408-9591 — —
91510-1 408-8547 90548-1 408-9885
91500-1 408-8547 90546-1 408-9883
Universal MATE-N-LOK 91508-1 408-8547 90547-1 408-9884
and
91506-1 408-8547 90547-1 408-9884
69710-11 408-2095 — —
58380-12 408-9433 — —
58380-2 2 408-9433 — —
58631-1 408-4341 — —
.156 MATE-N-LOK
58632-1 408-4340 — —
1Hand tool requires die set. 2Die set.
210
Soft Shell
Applicator Options
Heavy-Duty Miniature Applicator Part Numbers

Strip Form Contact
Part Number Used on Bench Top Terminators Used on Automatic Leadmaking Used on
AMP-O-LECTRIC AMP-O-LECTRIC Equipment (AMPOMATOR CLS AMP-O-MATIC
Pin Socket Model K Machine Model G Machine Machine with T or G Terminators) Stripper-Crimper Machine
2.5 mm Signal Double 917764-1 917683-1 * * * *
Lock (SDL) Contacts 917765-1 917684-1 * * * *
Micro MATE-N-LOK 1-794608-0 —
3 mm Connector 1-794608-1 — 1385194-2 1385194-3 1385194-1 —
System 1-794608-2 —
1-794609-0 —
1-794609-1 — 1385377-2 1385377-3 1385377-1 —
Applicator Options
1-794609-2 —
— 794606-1
— 1-794606-1 680893-2 680893-3 680893-1 —
— 1-794606-2
— 794607-1
— 1-794607-1 680894-2 680894-3 680894-1 —
— 1-794607-2
Grace Inertia 1565080-1 1565079-1 * * * *
Connectors (GIC) 3.5 1612335-1 1612334-1 * * * *
.062 Commercial Pin 640391-1 640392-1
and Socket Contacts 640391-5 640392-5
466686-2 466686-3 466686-1 466955-1
— 640392-2
— 794046-1
350629-1 350628-1
— 350628-2
350629-5 350628-5 687996-2 687996-3 687996-1 —
— 350628-6
— 794103-1
Power Double Lock 177914-1 * * * *
177916-1
(PDL) 177914-2† * * * *
177915-1 * * * *
177917-1
177915-2† * * * *
† High contact pressure type.
Mini-Universal 770835-1 770834-1
567418-2 567418-3 567418-1 —
MATE-N-LOK 1-770835-0 1-770834-0
Contacts 770901-1 770902-1
567066-4 567066-5 567066-3 466990-2
1-770901-0 1-770902-0
770903-1 770904-1
567067-2 567067-3 567067-1 466986-1
1-770903-0 1-770904-0
171636-1 171637-1
680582 567251-1 680582 567902-1
— 171637-3
Mini-Universal 794216-1 794217-1
567418-2 567418-3 567418-1 —
MATE-N-LOK 2 1-794216-0 1-794217-0
Contacts 794218-1 794219-1
567066-4 567066-5 567066-3 466990-2
1-794218-0 1-794219-0
794220-1 794221-1
680854-2 680854-3 680854-1 466986-1
1-794220-0 1-794221-0
794222-1 794223-1
680582-2 680582-3 — 567902-1
1-794222-0 1-794223-0
(MR) Miniature 350968-1 794000-1
466352-2 466352-3 466352-1 —
Rectangular 350968-2 794000-2
Contacts 350967-1 641294-1
466351-2 466351-4 466351-1 466913-1
350967-2 641294-2
350969-1 —
466351-2 466351-4 466351-1 466913-1
350969-2 —
Note: Stripper Crimper (SCA) and Crimp Quality Monitor Applicators may be available. Call Technical Support for Part Numbers.
211
Soft Shell
Applicator Options (Continued)

Strip Form Contact
VAL-U-LOK 794955-1 794956-1
Connector System 794955-2 794956-2
1385817-2 1385817-3 1385817-1 —
794955-3 794956-3
794955-4 794956-4
794957-1 794958-1
794957-2 794958-2
1385448-2 1385448-3 1385448-1 —
794957-3 794958-3
Applicator Options
794957-4 794958-4
AMP-DUAC 794576-1 106529-2
680308-2 680308-3 — 567959-1
1-794138-3
794578-1 106528-2
680307-2 680307-3 — 567960-1
1-794139-3
— 1-794140-3
680350-2 680350-3 — —
794418-1
5.0 mm Power Key — 1376347-1 * * * *
Connectors (PKC) — 1376348-1 * * * *
.093 Commercial Pin 350418-1 350417-1
and Socket Contacts — 350417-3 466656-2 466656-3 466656-1 466922-1
350418-5 350417-5
350416-1 350415-1
466878-2 466878-3 466878-1 466959-1
350416-5 350415-5
770530-1 770529-1 567337-4 567337-6 567337-3 —
770385-1 770383-1
567273-2 567273-4 567273-3 —
— —
Commercial 350079-1 350078-1
MATE-N-LOK 350079-4 350078-4 466426-2 466426-3 466426-1 —
Contacts 350079-5 350078-5
61116-1 61314-1
61116-4 61314-4
61116-5 61314-5 466320-2 466320-4 466320-1 466917-1
61116-6 61314-6
61116-7 61314-7
61118-1 61117-1
61118-4 61117-4
61118-5 61117-5 687763-2 687763-6 687763-1 466920-1
61118-6 61117-6
61118-7 61117-7
350558-1 350557-1
687898-2 687898-4 687898-1 —
350558-4 350557-4
61527-2 — 466320-2 466320-4 466320-1 466917-1
.140 MATE-N-LOK 61627-1 61626-1
567306-2 567306-3 567306-1 —
Contacts 61627-2 61626-2
350201-1 350200-1
567309-2 567309-3 587309-1 —
350201-2 350200-2
Universal 350924-1 350925-1
466616-2 466616-3 — —
MATE-N-LOK 350924-6 350925-6
Contacts 350561-1 350851-1
— 350570-1
350561-2 350851-2
— 350570-2
466320-2 466320-4 466320-1 466917-1
350561-7 350851-7
— 350570-7
350561-3 350570-3
— 350570-6
212
Soft Shell
Applicator Options (Continued)

Strip Form Contact
Universal 350218-1 350536-1
MATE-N-LOK 350218-2 350536-2
Contacts (Continued) 350218-7 350536-7 687763-2 687763-6 687763-1 466920-1
350218-3 350536-3
350218-6 350536-6
350538-1 350537-1
350538-2 350537-2
Applicator Options
350538-7 350537-7 687926-2 687926-6 687926-1 466989-1
350538-3 350537-3
350538-6 350537-6
350873-1 350874-1
466588-2 466588-3 466588-1 —
350873-3 350874-3
350922-3 350923-3
350922-6 350923-6 466597-2 466597-3 466597-1 —
350922-4 350923-4
350699-1 —
350699-2 — 466320-2 466320-4 466320-1 466917-1
350699-7 —
350687-1 —
350687-2 — 687763-2 687763-6 687763-1 466920-1
350687-7 —
350700-1 —
350700-2 — 687926-2 687926-6 687926-1 466989-1
350700-7 —
770210-1 — 567216-2 567216-3 567216-1
350654-1 — 687763-2 687763-6 687763-1 466920-1
770234-3 — 466597-2 466597-3 466597-1
Universal 770011-6 770012-6 — 567252-4 567252-1 —
MATE-N-LOK II 770009-1 —
Contacts 1-770009-0 —
— 567214-4 567214-1 567914-1
— 770010-3
— 1-770010-0
770007-1 —
1-770007-0 —
— 567213-4 567213-1 567913-1
— 770008-3
— 1-770008-0
770005-1 —
1-770005-0 —
— 567212-4 567212-1 —
— 770006-3
1-770005-1 1-770006-0
770003-3 770004-3
— 567211-4 567211-1 —
1-770003-0 1-770004-0
770193-1 —
— 567213-4 567213-1 567913-1
1-770193-0 —
770194-1 —
— 567212-4 567212-1 —
1-770194-0 —
.156 MATE-N-LOK 61086-1 61085-1 466462-1 466462-3 466462-1 —
Contacts 61234-1 61233-1 687765-2 687765-2 — —
213
Soft Shell
Product Feature Comparisons

2.5 mm Grace .062 Power Sealed
Signal Micro Inertia Commercial Double Mini- Mini- Mini- (MR) VAL-U-LOK
High Density Double MATE-N-LOK Connectors Pin & Lock Universal Universal Universal Miniature Connector AMP-
Lock (SDL) 3 mm (GIC) 3.5 Socket (PDL) MATE-N-LOK MATE-N-LOK MATE-N-LOK 2 Rectangular System DUAC
Wire AWG —
Maximum 20 20 18 18 16 16 18 16 18 18 18
Minimum 26 30 26 30 26 30 26 30 26 26 26
Current Rating —
10 AWG Wire — — — — —
14 AWG Wire — — — — — — — — — — —
16 AWG Wire — — 14 — —
18 AWG Wire — ** 7 17 — 9 9 10.5 6 9 9
20 AWG Wire 3 — — — —
Max. Operating Voltage
(AC or DC) 50 250 300 250 300 600 600 600 250 600 600
UL 94V-0 Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes
UL 94V-2 No No No Yes No Yes* No Yes No Yes Yes
Approvals —
UL Yes Yes Yes Yes Yes Yes Yes Submitted Yes Yes Yes
CSA Yes Yes Yes Yes Yes Yes Yes Submitted Yes Yes Yes
VDE Yes Yes — No Yes Yes Yes Submitted No — No
Contact Material —
Brass No Yes Yes Yes Yes Yes Yes Yes No Yes —
Phos. Bronze Yes Yes No Yes No Yes Yes No Yes Yes Yes
Plating Finish —
Tin Plating Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
Gold Plating No Yes No Yes No Yes Yes Yes Yes Yes Yes
.156 [3.96]
.098 .118 .137 .145 256 [6.50] .163 .163 .163 .165 .165 .165
Centerline Spacing — [2.50] [3.00] [3.50] [3.68] .312 [7.92] [4.14] [4.14] [4.14] [4.20] [4.20] [4.20]
.512 [13.00]
Housings —
Panel Mount No Yes No Yes Yes Yes Yes No Yes Yes Yes
Free-Hanging Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes
Secondary Locking Latches Yes No Yes No Yes No No Yes No Yes Yes
Contact Position Control Yes No No No No No No Yes No No Yes
In-Line Config. Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes
Dual Row Config. No Yes Yes No Yes Yes Yes Yes No Yes Yes
Matrix Config. No No No Yes Yes Yes No Yes Yes No No
Accessories —
Strain Relief No No Yes No Yes Yes No No Yes No Yes
Keying Plug No No No No No Yes Yes Yes Yes No No
Seals No No No No No Yes Yes No No No No
Headers —
Mini-Universal
Vertical Yes Yes No No Yes Yes Yes MATE-N-LOK Yes Yes Yes
Mini-Universal
Blindmate No No No No No Yes Yes MATE-N-LOK No Yes No
Mini-Universal
Right-Angle Planned Yes No No No Yes Yes MATE-N-LOK No Yes Yes
Positions —
Minimum 2 2 2 1 1 1 2 2 2 2 2
Maximum 13 24 6 9 12 24 10 24 36 24 24
* Wire-to-Wire Only.
** 5 A on 20 AWG*
214
Soft Shell
Product Feature Comparisons (Continued)

5.0 mm .093
Standard Density Power Key Commercial Commercial .140 Universal Universal .156
Connectors (PKC) Pin & Socket MATE-N-LOK MATE-N-LOK MATE-N-LOK MATE-N-LOK II MATE-N-LOK
Wire AWG—
Maximum 16 14 14 10 10 10 10
Minimum 24 24 30 20 30 30 20
Current Rating —
10 AWG Wire — 28 32.5
14 AWG Wire — 19 13 — 15 19 —
16 AWG Wire 10 — —
18 AWG Wire — — — — — — —
20 AWG Wire — — —
Max. Operating Voltage (AC or DC) 300 250 250 600 600 600 600

UL 94V-0 Yes No Yes No Yes Yes No
UL 94V-2 No Yes Yes Yes Yes No Yes
Approvals —
UL Yes Yes Yes Yes Yes Yes Yes
CSA Yes Yes Yes Yes Yes Yes No
VDE No No No No Yes Yes No
Contact Material —
Brass Yes Yes Yes Yes Yes Yes Yes
Phos. Bronze No Yes Yes Yes Yes Yes No
Plating Finish —
Tin Plating Yes Yes Yes Yes Yes Yes Yes
Gold Plating No Yes Yes No Yes Yes No
.198 [5.03] .200 [5.08]
Centerline Spacing — .197 [5.00] .250 [6.35] .240 [6.10] x .202 [5.13] .240 [6.10] .250 [6.35] .250 [6.35] .390 [9.91]
.248 [6.30] .195 [4.95] x .360 [9.14]
Housings —
Panel Mount No Yes Yes Yes Yes Yes Yes
Free-Hanging No Yes Yes Yes Yes Yes Yes
Secondary Locking Latches Yes No No Yes No Yes Yes
Contact Position Control No No No No No Yes No
In-Line Config. Yes Yes Yes Yes Yes Yes Yes
Dual Row Config. Yes No Yes No No No No
Matrix Config. No Yes Yes Yes Yes Yes No
Accessories —
Universal
Strain Relief Yes No No No Yes MATE-N-LOK No
Keying Plug No No Yes No Yes Yes No
Seals No No No No Yes No No
Headers —
Universal
Vertical Yes No Yes No Yes MATE-N-LOK No
Blindmate No No No No No No No
Universal
Right-Angle No No Yes No Yes MATE-N-LOK No
Positions —
Minimum 2 1 1 2 1 2 3
Maximum 6 15 16 9 15 15 4
* Wire-to-Wire Only.
** 5 A on 20 AWG*
215
Soft Shell
Non-Compliant to RoHS Compliant Part Number Cross Reference
Non-Compliant RoHS Compliant Non-Compliant RoHS Compliant Non-Compliant RoHS Compliant Non-Compliant RoHS Compliant
Part Number Part Number Part Number Part Number Part Number Part Number Part Number Part Number
350209-2 1586512-2 350827-2 350827-4 643234-2 3-643234-0 770876-1 1-770876-0
350210-2 1586514-2 350828-2 350828-4 643236-2 3-643236-0 770876-2 1-770876-1
350211-2 1586515-2 350829-2 350829-4 643410-2 643410-3 770901-3 1-770901-0
350211-3 1586515-3 350830-2 350830-4 643412-2 643412-3 770902-3 1-770902-0
350212-2 1586518-2 350832-2 350832-4 643414-2 643414-3 770902-6 1-770902-1
350213-2 1586520-2 350833-2 350833-4 643424-2 643424-3 770903-3 1-770903-0
350214-2 1586522-2 350834-2 350834-4 643426-2 643426-3 770903-6 1-770903-1
350220-2 1586524-2 350835-2 350835-4 770003-4 1-770003-0 770904-3 1-770904-0
1-350375-0 2-350375-0 350836-2 350836-4 770004-4 1-770004-0 770904-6 1-770904-1
1-350376-0 2-350376-0 350837-2 350837-4 770005-2 1-770005-0 770966-1 1-770966-0
1-350377-0 2-350377-0 2-350942-0 3-350942-0 770005-4 1-770005-1 770966-2 1-770966-1
1-350378-1 2-350378-1 2-350943-0 3-350943-0 770006-4 1-770006-0 770967-1 1-770967-0
1-350379-1 2-350379-1 2-350944-0 3-350944-0 770007-2 1-770007-0 770967-2 1-770967-1
1-350380-1 2-350380-1 2-350945-0 3-350945-0 770008-4 1-770008-0 770968-1 1-770968-0
350424-2 1586525-2 350988-3 350988-5 770010-4 1-770010-0 770968-2 1-770968-1
350425-2 1586526-2 350989-3 350989-5 770166-1 1-770166-0 770969-1 1-770969-0

350426-2 1586528-2 350990-3 350990-5 770166-2 1-770166-1 770969-2 1-770969-1
350428-2 350428-4 350991-3 350991-5 770170-1 1-770170-0 770970-1 1-770970-0
350429-2 350429-4 1-380935-0 2-380935-0 770170-2 1-770170-1 770970-2 1-770970-1
350430-2 350430-4 1-380936-0 2-380936-0 770174-1 1-770174-0 770971-1 1-770971-0
350431-2 350431-4 1-380937-0 2-380937-0 770174-2 1-770174-1 770971-2 1-770971-1
350432-2 350432-4 2-380991-0 2-1586544-0 770178-1 1-770178-0 770972-1 1-770972-0
350433-2 350433-4 2-380999-0 2-1586546-0 770178-2 1-770178-1 770972-2 1-770972-1
350434-2 350434-4 640466-2 640466-3 770182-1 1-770182-0 770973-1 1-770973-0
350539-2 1586530-2 640467-2 640467-3 770182-2 1-770182-1 770973-2 1-770973-1
350541-2 1586532-2 640497-2 2-640497-2 770186-1 1-770186-0 770974-1 1-770974-0
350543-2 1586534-2 640497-4 2-640497-4 770186-2 1-770186-1 770974-2 1-770974-1
350544-2 1586536-2 640498-2 2-640498-2 770190-1 1-770190-0 770985-3 1-770985-0
350582-2 350582-4 640498-4 2-640498-4 770190-2 1-770190-1 770986-3 1-770986-0
350583-2 350583-4 640499-2 2-640499-2 770193-2 1-770193-0 770987-3 1-770987-0
350584-2 350584-4 640499-4 2-640499-4 770194-2 1-770194-0 770988-3 1-770988-0
350585-2 350585-4 640500-2 2-640500-2 770246-4 1-770246-0 794040-1 1-794040-0
350586-2 350586-4 640500-4 2-640500-4 770247-4 1-770247-0 794040-2 1-794040-1
350587-2 350587-4 640501-2 2-640501-2 770248-2 1-770248-0 794058-3 1-794058-0
350588-2 350588-4 640501-4 2-640501-4 770249-4 1-770249-0 794059-3 1-794059-0
350641-2 1586539-2 640502-2 2-640502-2 770250-2 1-770250-0 794065-1 1-794065-0
350711-2 350711-4 640502-4 2-640502-4 770251-4 1-770251-0 794065-2 1-794065-1
350712-2 350712-4 640503-2 2-640503-2 770252-2 1-770252-0 794066-1 1-794066-0
350713-2 350713-4 640503-4 2-640503-4 770254-2 1-770254-0 794066-2 1-794066-1
350714-2 350714-4 640504-2 2-640504-2 770255-2 1-770255-0 794067-1 1-794067-0
350714-3 350714-5 640504-4 2-640504-4 770262-2 770262-3 794067-2 1-794067-1
350732-2 350732-4 640505-2 2-640505-2 770328-1 1586627-1 794068-1 1-794068-0
350737-2 350737-4 640505-4 2-640505-4 1-770328-1 1-1586627-1 794068-2 1-794068-1
350738-2 350738-4 640506-2 2-640506-2 770621-1 1-770621-0 794069-1 1-794069-0
350742-2 350742-4 640506-4 2-640506-4 770621-2 1-770621-1 794069-2 1-794069-1
350759-3 350759-5 640583-2 640583-3 770743-1 1-770743-0 794070-1 1-794070-0
350760-3 350760-5 640584-2 640584-3 770743-2 1-770743-1 794070-2 1-794070-1
350761-3 350761-5 640900-2 640900-3 770834-3 1-770834-0 794071-1 1-794071-0
350762-3 350762-5 640901-2 640901-3 770834-6 1-770834-1 794071-2 1-794071-1
350763-3 350763-5 641831-2 641831-3 770835-3 1-770835-0 794072-1 1-794072-0
350764-3 350764-5 641832-2 641832-3 770858-1 1-770858-0 794072-2 1-794072-1
350765-3 350765-5 641963-2 641963-3 770858-2 1-770858-1 794073-1 1-794073-0
350786-2 350786-3 641964-2 641964-3 770859-1 1-770859-0 794073-2 1-794073-1
350787-2 350787-3 641970-2 641970-3 770859-2 1-770859-1 794074-1 1-794074-0
350789-2 350789-3 641971-2 641971-3 770872-1 1-770872-0 794074-2 1-794074-1
350790-2 350790-3 641972-2 641972-3 770872-2 1-770872-1 794075-2 1-794075-1
350792-2 350792-3 641974-2 641974-3 770873-1 1-770873-0 794076-1 1-794076-0
350793-2 350793-3 641976-2 641976-4 770873-2 1-770873-1 794076-2 1-794076-1
350824-2 350824-4 643228-2 3-643228-0 770874-2 1-770874-1 794077-1 1-794077-0
350825-2 350825-4 643230-2 3-643230-0 770875-1 1-770875-0 794077-2 1-794077-1
350826-2 350826-4 643232-2 3-643232-0 770875-2 1-770875-1 794078-1 1-794078-0
216
Soft Shell
Non-Compliant to RoHS Compliant Part Number Cross Reference (Continued)
794078-2 1-794078-1 794313-1 794313-3 794472-2 1-794472-2 794610-2 1-794610-1
794079-1 1-794079-0 794313-2 794313-4 794484-1 1-794484-1 794610-3 1-794610-2
794079-2 1-794079-1 794325-1 1-794325-0 794484-2 1-794484-2 794611-2 1-794611-1
794105-1 1-794105-0 794326-2 1-794326-1 794485-1 1-794485-1 794611-3 1-794611-2
794105-2 1-794105-1 794327-1 1-794327-0 794485-2 1-794485-2 794612-1 1-794612-0
794106-1 1-794106-0 794327-2 1-794327-1 794486-1 1-794486-1 794612-2 1-794612-1
794106-2 1-794106-1 794328-1 1-794328-0 794486-2 1-794486-2 794612-3 1-794612-2
794107-1 1-794107-0 794330-2 1-794330-1 794487-1 1-794487-1 794613-1 1-794613-0
794107-2 1-794107-1 794349-1 1-794349-1 794487-2 1-794487-2 794613-2 1-794613-1
794108-1 1-794108-0 794349-2 1-794349-2 794488-1 1-794488-1 794613-3 1-794613-2
794108-2 1-794108-1 794350-1 1-794350-1 794488-2 1-794488-2 794618-2 3-794618-2
794126-1 1-794126-0 794350-2 1-794350-2 794489-1 1-794489-1 794618-4 3-794618-4
794130-2 1-794130-1 794351-1 1-794351-1 794489-2 1-794489-2 794618-6 3-794618-6
794136-3 1-794136-1 794351-2 1-794351-2 794490-1 1-794490-1 794618-8 3-794618-8
794137-3 1-794137-1 794352-1 1-794352-1 794490-2 1-794490-2 1-794618-0 4-794618-0

794138-3 1-794138-3 794352-2 1-794352-2 794491-1 1-794491-1 1-794618-2 4-794618-2
794139-3 1-794139-3 794353-1 1-794353-1 794491-2 1-794491-2 1-794618-4 4-794618-4
794140-3 1-794140-3 794353-2 1-794353-2 794492-1 1-794492-1 1-794618-6 4-794618-6
794141-3 1-794141-3 794354-1 1-794354-1 794492-2 1-794492-2 1-794618-8 4-794618-8
794142-3 1-794142-3 794354-2 1-794354-2 794493-1 1-794493-1 2-794618-0 5-794618-0
794143-3 1-794143-3 794355-1 1-794355-1 794493-2 1-794493-2 2-794618-2 5-794618-2
794181-1 1-794181-1 794355-2 1-794355-2 794494-1 1-794494-1 2-794618-4 5-794618-4
794181-2 1-794181-2 794356-1 1-794356-1 794494-2 1-794494-2 794619-2 3-794619-2
794216-3 1-794216-0 794356-2 1-794356-2 794507-1 1-794507-1 794619-4 3-794619-4
794217-3 1-794217-0 794357-1 1-794357-1 794508-1 1-794508-1 794619-6 3-794619-6
794218-3 1-794218-0 794357-2 1-794357-2 794509-1 1-794509-1 794619-8 3-794619-8
794219-3 1-794219-0 794358-1 1-794358-1 794510-1 1-794510-1 1-794619-0 4-794619-0
794220-3 1-794220-0 794358-2 1-794358-2 794511-1 1-794511-1 1-794619-2 4-794619-2
794221-3 1-794221-0 794359-1 1-794359-1 794512-1 1-794512-1 1-794619-4 4-794619-4
794222-3 1-794222-0 794359-2 1-794359-2 794513-1 1-794513-1 1-794619-6 4-794619-6
794223-3 1-794223-0 794360-1 1-794360-1 794514-1 1-794514-1 1-794619-8 4-794619-8
794224-3 1-794224-0 794360-2 1-794360-2 794515-1 1-794515-1 2-794619-0 5-794619-0
794225-3 1-794225-0 794374-1 1-794374-0 794516-1 1-794516-1 2-794619-2 5-794619-2
794226-3 1-794226-0 794374-2 1-794374-1 794526-1 1-794526-1 2-794619-4 5-794619-4
794227-3 1-794227-0 794406-3 1-794406-0 794527-1 1-794527-1 794620-2 3-794620-2
794228-3 1-794228-0 794407-3 1-794407-0 794528-1 1-794528-1 794620-4 3-794620-4
794229-3 1-794229-0 794415-1 1-794415-1 794529-1 1-794529-1 794620-6 3-794620-6
794230-3 1-794230-0 794415-2 1-794415-2 794530-1 1-794530-1 794620-8 3-794620-8
794231-3 1-794231-0 794429-1 1-794429-1 794531-1 1-794531-1 1-794620-0 4-794620-0
794302-1 1-794302-1 794429-2 1-794429-2 794532-1 1-794532-1 1-794620-2 4-794620-2
794302-2 1-794302-2 794448-1 1-794448-1 794533-1 1-794533-1 1-794620-4 4-794620-4
794303-1 1-794303-1 794449-1 1-794449-1 794534-1 1-794534-1 1-794620-6 4-794620-6
794303-2 1-794303-2 794453-1 1-794453-1 794540-1 1-794540-1 1-794620-8 4-794620-8
794304-1 1-794304-1 794453-2 1-794453-2 794540-2 1-794540-2 2-794620-0 5-794620-0
794304-2 1-794304-2 794454-1 1-794454-1 794543-1 1-794543-1 2-794620-2 5-794620-2
794305-1 1-794305-1 794454-2 1-794454-2 794543-2 1-794543-2 2-794620-4 5-794620-4
794305-2 1-794305-2 794455-1 1-794455-1 794576-2 794576-4 794621-2 3-794621-2
794306-1 1-794306-1 794455-2 1-794455-2 794578-2 794578-4 794621-4 3-794621-4
794306-2 1-794306-2 794466-1 1-794466-1 794588-1 1-794588-1 794621-6 3-794621-6
794307-1 1-794307-1 794466-2 1-794466-2 794589-1 1-794589-1 794621-8 3-794621-8
794307-2 1-794307-2 794467-1 1-794467-1 794590-1 1-794590-1 1-794621-0 4-794621-0
794308-1 1-794308-1 794467-2 1-794467-2 794606-2 1-794606-1 1-794621-2 4-794621-2
794308-2 1-794308-2 794468-1 1-794468-1 794606-3 1-794606-2 1-794621-4 4-794621-4
794309-1 1-794309-1 794468-2 1-794468-2 794607-2 1-794607-1 1-794621-6 4-794621-6
794309-2 1-794309-2 794469-1 1-794469-1 794607-3 1-794607-2 1-794621-8 4-794621-8
794310-1 1-794310-1 794469-2 1-794469-2 794608-1 1-794608-0 2-794621-0 5-794621-0
794310-2 1-794310-2 794470-1 1-794470-1 794608-2 1-794608-1 2-794621-2 5-794621-2
794311-1 1-794311-1 794470-2 1-794470-2 794608-3 1-794608-2 2-794621-4 5-794621-4
794311-2 1-794311-2 794471-1 1-794471-1 794609-1 1-794609-0 794622-2 3-794622-2
794312-1 1-794312-1 794471-2 1-794471-2 794609-2 1-794609-1 794622-4 3-794622-4
794312-2 1-794312-2 794472-1 1-794472-1 794609-3 1-794609-2 794622-6 3-794622-6
217
Soft Shell
794622-8 3-794622-8 1-794627-0 4-794627-0 1-794632-2 4-794632-2 1-794637-4 4-794637-4
1-794622-0 4-794622-0 1-794627-2 4-794627-2 1-794632-4 4-794632-4 1-794637-6 4-794637-6
1-794622-2 4-794622-2 1-794627-4 4-794627-4 1-794632-6 4-794632-6 1-794637-8 4-794637-8
1-794622-4 4-794622-4 1-794627-6 4-794627-6 1-794632-8 4-794632-8 2-794637-0 5-794637-0
1-794622-6 4-794622-6 1-794627-8 4-794627-8 2-794632-0 5-794632-0 2-794637-2 5-794637-2
1-794622-8 4-794622-8 2-794627-0 5-794627-0 2-794632-2 5-794632-2 2-794637-4 5-794637-4
2-794622-0 5-794622-0 2-794627-2 5-794627-2 2-794632-4 5-794632-4 794638-2 3-794638-2
2-794622-2 5-794622-2 2-794627-4 5-794627-4 794633-2 3-794633-2 794638-4 3-794638-4
2-794622-4 5-794622-4 794628-2 3-794628-2 794633-4 3-794633-4 794638-6 3-794638-6
794623-2 3-794623-2 794628-4 3-794628-4 794633-6 3-794633-6 794638-8 3-794638-8
794623-4 3-794623-4 794628-6 3-794628-6 794633-8 3-794633-8 1-794638-0 4-794638-0
794623-6 3-794623-6 794628-8 3-794628-8 1-794633-0 4-794633-0 1-794638-2 4-794638-2
794623-8 3-794623-8 1-794628-0 4-794628-0 1-794633-2 4-794633-2 1-794638-4 4-794638-4
1-794623-0 4-794623-0 1-794628-2 4-794628-2 1-794633-4 4-794633-4 1-794638-6 4-794638-6
1-794623-2 4-794623-2 1-794628-4 4-794628-4 1-794633-6 4-794633-6 1-794638-8 4-794638-8
1-794623-4 4-794623-4 1-794628-6 4-794628-6 1-794633-8 4-794633-8 2-794638-0 5-794638-0

1-794623-6 4-794623-6 1-794628-8 4-794628-8 2-794633-0 5-794633-0 2-794638-2 5-794638-2
1-794623-8 4-794623-8 2-794628-0 5-794628-0 2-794633-2 5-794633-2 2-794638-4 5-794638-4
2-794623-0 5-794623-0 2-794628-2 5-794628-2 2-794633-4 5-794633-4 794662-2 1586489-2
2-794623-2 5-794623-2 2-794628-4 5-794628-4 794634-2 3-794634-2 794662-4 1586489-4
2-794623-4 5-794623-4 794629-2 3-794629-2 794634-4 3-794634-4 794662-6 1586489-6
794624-2 3-794624-2 794629-4 3-794629-4 794634-6 3-794634-6 794662-8 1586489-8
794624-4 3-794624-4 794629-6 3-794629-6 794634-8 3-794634-8 1-794662-0 1-1586489-0
794624-6 3-794624-6 794629-8 3-794629-8 1-794634-0 4-794634-0 1-794662-2 1-1586489-2
794624-8 3-794624-8 1-794629-0 4-794629-0 1-794634-2 4-794634-2 1-794662-4 1-1586489-4
1-794624-0 4-794624-0 1-794629-2 4-794629-2 1-794634-4 4-794634-4 1-794662-6 1-1586489-6
1-794624-2 4-794624-2 1-794629-4 4-794629-4 1-794634-6 4-794634-6 1-794662-8 1-1586489-8
1-794624-4 4-794624-4 1-794629-6 4-794629-6 1-794634-8 4-794634-8 2-794662-0 2-1586489-0
1-794624-6 4-794624-6 1-794629-8 4-794629-8 2-794634-0 5-794634-0 2-794662-2 2-1586489-2
1-794624-8 4-794624-8 2-794629-0 5-794629-0 2-794634-2 5-794634-2 2-794662-4 2-1586489-4
2-794624-0 5-794624-0 2-794629-2 5-794629-2 2-794634-4 5-794634-4 794663-2 1586490-2
2-794624-2 5-794624-2 2-794629-4 5-794629-4 794635-2 3-794635-2 794663-4 1586490-4
2-794624-4 5-794624-4 794630-2 3-794630-2 794635-4 3-794635-4 794663-6 1586490-6
794625-2 3-794625-2 794630-4 3-794630-4 794635-6 3-794635-6 794663-8 1586490-8
794625-4 3-794625-4 794630-6 3-794630-6 794635-8 3-794635-8 1-794663-0 1-1586490-0
794625-6 3-794625-6 794630-8 3-794630-8 1-794635-0 4-794635-0 1-794663-2 1-1586490-2
794625-8 3-794625-8 1-794630-0 4-794630-0 1-794635-2 4-794635-2 1-794663-4 1-1586490-4
1-794625-0 4-794625-0 1-794630-2 4-794630-2 1-794635-4 4-794635-4 1-794663-6 1-1586490-6
1-794625-2 4-794625-2 1-794630-4 4-794630-4 1-794635-6 4-794635-6 1-794663-8 1-1586490-8
1-794625-4 4-794625-4 1-794630-6 4-794630-6 1-794635-8 4-794635-8 2-794663-0 2-1586490-0
1-794625-6 4-794625-6 1-794630-8 4-794630-8 2-794635-0 5-794635-0 2-794663-2 2-1586490-2
1-794625-8 4-794625-8 2-794630-0 5-794630-0 2-794635-2 5-794635-2 2-794663-4 2-1586490-4
2-794625-0 5-794625-0 2-794630-2 5-794630-2 2-794635-4 5-794635-4 794664-2 1586491-2
2-794625-2 5-794625-2 2-794630-4 5-794630-4 794636-2 3-794636-2 794664-4 1586491-4
2-794625-4 5-794625-4 794631-2 3-794631-2 794636-4 3-794636-4 794664-6 1586491-6
794626-2 3-794626-2 794631-4 3-794631-4 794636-6 3-794636-6 794664-8 1586491-8
794626-4 3-794626-4 794631-6 3-794631-6 794636-8 3-794636-8 1-794664-0 1-1586491-0
794626-6 3-794626-6 794631-8 3-794631-8 1-794636-0 4-794636-0 1-794664-2 1-1586491-2
794626-8 3-794626-8 1-794631-0 4-794631-0 1-794636-2 4-794636-2 1-794664-4 1-1586491-4
1-794626-0 4-794626-0 1-794631-2 4-794631-2 1-794636-4 4-794636-4 1-794664-6 1-1586491-6
1-794626-2 4-794626-2 1-794631-4 4-794631-4 1-794636-6 4-794636-6 1-794664-8 1-1586491-8
1-794626-4 4-794626-4 1-794631-6 4-794631-6 1-794636-8 4-794636-8 2-794664-0 2-1586491-0
1-794626-6 4-794626-6 1-794631-8 4-794631-8 2-794636-0 5-794636-0 2-794664-2 2-1586491-2
1-794626-8 4-794626-8 2-794631-0 5-794631-0 2-794636-2 5-794636-2 2-794664-4 2-1586491-4
2-794626-0 5-794626-0 2-794631-2 5-794631-2 2-794636-4 5-794636-4 794665-2 1586492-2
2-794626-2 5-794626-2 2-794631-4 5-794631-4 794637-2 3-794637-2 794665-4 1586492-4
2-794626-4 5-794626-4 794632-2 3-794632-2 794637-4 3-794637-4 794665-6 1586492-6
794627-2 3-794627-2 794632-4 3-794632-4 794637-6 3-794637-6 794665-8 1586492-8
794627-4 3-794627-4 794632-6 3-794632-6 794637-8 3-794637-8 1-794665-0 1-1586492-0
794627-6 3-794627-6 794632-8 3-794632-8 1-794637-0 4-794637-0 1-794665-2 1-1586492-2
794627-8 3-794627-8 1-794632-0 4-794632-0 1-794637-2 4-794637-2 1-794665-4 1-1586492-4
218
Soft Shell
1-794665-8 1-1586492-8 2-794677-0 5-794677-0 2-794682-2 5-794682-2 1445055-5 2-1445055-5
2-794665-0 2-1586492-0 2-794677-2 5-794677-2 2-794682-4 5-794682-4 1445055-6 2-1445055-6
2-794665-2 2-1586492-2 2-794677-4 5-794677-4 794704-1 1586542-1 1445055-7 2-1445055-7
2-794665-4 2-1586492-4 794678-2 3-794678-2 1445050-2 2-1445050-2 1445055-8 2-1445055-8
794666-2 1586493-2 794678-4 3-794678-4 1445050-3 2-1445050-3 1445055-9 2-1445055-9
794666-4 1586493-4 794678-6 3-794678-6 1445050-4 2-1445050-4 1-1445055-0 3-1445055-0
794666-6 1586493-6 794678-8 3-794678-8 1445050-5 2-1445050-5 1-1445055-1 3-1445055-1
794666-8 1586493-8 1-794678-0 4-794678-0 1445050-6 2-1445050-6 1-1445055-2 3-1445055-2
1-794666-0 1-1586493-0 1-794678-2 4-794678-2 1445050-7 2-1445050-7 1445056-2 2-1445056-2
1-794666-2 1-1586493-2 1-794678-4 4-794678-4 1445050-8 2-1445050-8 1445056-3 2-1445056-3
1-794666-4 1-1586493-4 1-794678-6 4-794678-6 1445050-9 2-1445050-9 1445056-4 2-1445056-4
1-794666-6 1-1586493-6 1-794678-8 4-794678-8 1-1445050-0 3-1445050-0 1445056-5 2-1445056-5
1-794666-8 1-1586493-8 2-794678-0 5-794678-0 1-1445050-1 3-1445050-1 1445056-6 2-1445056-6
2-794666-0 2-1586493-0 2-794678-2 5-794678-2 1-1445050-2 3-1445050-2 1445056-7 2-1445056-7
2-794666-2 2-1586493-2 2-794678-4 5-794678-4 1445051-2 2-1445051-2 1445056-8 2-1445056-8

2-794666-4 2-1586493-4 794679-2 3-794679-2 1445051-3 2-1445051-3 1445056-9 2-1445056-9
794667-2 1586494-2 794679-4 3-794679-4 1445051-4 2-1445051-4 1-1445056-0 3-1445056-0
794667-4 1586494-4 794679-6 3-794679-6 1445051-5 2-1445051-5 1-1445056-1 3-1445056-1
794667-6 1586494-6 794679-8 3-794679-8 1445051-6 2-1445051-6 1-1445056-2 3-1445056-2
794667-8 1586494-8 1-794679-0 4-794679-0 1445051-7 2-1445051-7 1445057-2 2-1445057-2
1-794667-0 1-1586494-0 1-794679-2 4-794679-2 1445051-8 2-1445051-8 1445057-3 2-1445057-3
1-794667-2 1-1586494-2 1-794679-4 4-794679-4 1445051-9 2-1445051-9 1445057-4 2-1445057-4
1-794667-4 1-1586494-4 1-794679-6 4-794679-6 1-1445051-0 3-1445051-0 1445057-5 2-1445057-5
1-794667-6 1-1586494-6 1-794679-8 4-794679-8 1-1445051-1 3-1445051-1 1445057-6 2-1445057-6
1-794667-8 1-1586494-8 2-794679-0 5-794679-0 1-1445051-2 3-1445051-2 1445057-7 2-1445057-7
2-794667-0 2-1586494-0 2-794679-2 5-794679-2 1445052-2 2-1445052-2 1445057-8 2-1445057-8
2-794667-2 2-1586494-2 2-794679-4 5-794679-4 1445052-3 2-1445052-3 1445057-9 2-1445057-9
2-794667-4 2-1586494-4 794680-2 3-794680-2 1445052-4 2-1445052-4 1-1445057-0 3-1445057-0
794668-2 1586495-2 794680-4 3-794680-4 1445052-5 2-1445052-5 1-1445057-1 3-1445057-1
794668-4 1586495-4 794680-6 3-794680-6 1445052-6 2-1445052-6 1-1445057-2 3-1445057-2
794668-6 1586495-6 794680-8 3-794680-8 1445052-7 2-1445052-7 1445058-2 2-1445058-2
794668-8 1586495-8 1-794680-0 4-794680-0 1445052-8 2-1445052-8 1445058-3 2-1445058-3
1-794668-0 1-1586495-0 1-794680-2 4-794680-2 1445052-9 2-1445052-9 1445058-4 2-1445058-4
1-794668-2 1-1586495-2 1-794680-4 4-794680-4 1-1445052-0 3-1445052-0 1445058-5 2-1445058-5
1-794668-4 1-1586495-4 1-794680-6 4-794680-6 1-1445052-1 3-1445052-1 1445058-6 2-1445058-6
1-794668-6 1-1586495-6 1-794680-8 4-794680-8 1-1445052-2 3-1445052-2 1445058-7 2-1445058-7
1-794668-8 1-1586495-8 2-794680-0 5-794680-0 1445053-2 2-1445053-2 1445058-8 2-1445058-8
2-794668-0 2-1586495-0 2-794680-2 5-794680-2 1445053-3 2-1445053-3 1445058-9 2-1445058-9
2-794668-2 2-1586495-2 2-794680-4 5-794680-4 1445053-4 2-1445053-4 1-1445058-0 3-1445058-0
2-794668-4 2-1586495-4 794681-2 3-794681-2 1445053-5 2-1445053-5 1-1445058-1 3-1445058-1
794669-2 1586496-2 794681-4 3-794681-4 1445053-6 2-1445053-6 1-1445058-2 3-1445058-2
794669-4 1586496-4 794681-6 3-794681-6 1445053-7 2-1445053-7 1445084-2 2-1445084-2
794669-6 1586496-6 794681-8 3-794681-8 1445053-8 2-1445053-8 1445084-3 2-1445084-3
794669-8 1586496-8 1-794681-0 4-794681-0 1445053-9 2-1445053-9 1445084-4 2-1445084-4
1-794669-0 1-1586496-0 1-794681-2 4-794681-2 1-1445053-0 3-1445053-0 1445084-5 2-1445084-5
1-794669-2 1-1586496-2 1-794681-4 4-794681-4 1-1445053-1 3-1445053-1 1445084-6 2-1445084-6
1-794669-4 1-1586496-4 1-794681-6 4-794681-6 1-1445053-2 3-1445053-2 1445084-7 2-1445084-7
1-794669-6 1-1586496-6 1-794681-8 4-794681-8 1445054-2 2-1445054-2 1445084-8 2-1445084-8
1-794669-8 1-1586496-8 2-794681-0 5-794681-0 1445054-3 2-1445054-3 1445084-9 2-1445084-9
2-794669-0 2-1586496-0 2-794681-2 5-794681-2 1445054-4 2-1445054-4 1-1445084-0 3-1445084-0
2-794669-2 2-1586496-2 2-794681-4 5-794681-4 1445054-5 2-1445054-5 1-1445084-1 3-1445084-1
2-794669-4 2-1586496-4 794682-2 3-794682-2 1445054-6 2-1445054-6 1-1445084-2 3-1445084-2
794677-2 3-794677-2 794682-4 3-794682-4 1445054-7 2-1445054-7 1445085-2 2-1445085-2
794677-4 3-794677-4 794682-6 3-794682-6 1445054-8 2-1445054-8 1445085-3 2-1445085-3
794677-6 3-794677-6 794682-8 3-794682-8 1445054-9 2-1445054-9 1445085-4 2-1445085-4
794677-8 3-794677-8 1-794682-0 4-794682-0 1-1445054-0 3-1445054-0 1445085-5 2-1445085-5
1-794677-0 4-794677-0 1-794682-2 4-794682-2 1-1445054-1 3-1445054-1 1445085-6 2-1445085-6
1-794677-2 4-794677-2 1-794682-4 4-794682-4 1-1445054-2 3-1445054-2 1445085-7 2-1445085-7
1-794677-4 4-794677-4 1-794682-6 4-794682-6 1445055-2 2-1445055-2 1445085-8 2-1445085-8
1-794677-6 4-794677-6 1-794682-8 4-794682-8 1445055-3 2-1445055-3 1445085-9 2-1445085-9
1-794677-8 4-794677-8 2-794682-0 5-794682-0 1445055-4 2-1445055-4 1-1445085-0 3-1445085-0
219
Soft Shell
1-1445085-1 3-1445085-1 1-1445089-2 3-1445089-2 1445094-2 2-1445094-2 1445098-3 2-1445098-3
1-1445085-2 3-1445085-2 1445090-2 2-1445090-2 1445094-3 2-1445094-3 1445098-4 2-1445098-4
1445086-2 2-1445086-2 1445090-3 2-1445090-3 1445094-4 2-1445094-4 1445098-5 2-1445098-5
1445086-3 2-1445086-3 1445090-4 2-1445090-4 1445094-5 2-1445094-5 1445098-6 2-1445098-6
1445086-4 2-1445086-4 1445090-5 2-1445090-5 1445094-6 2-1445094-6 1445098-7 2-1445098-7
1445086-5 2-1445086-5 1445090-6 2-1445090-6 1445094-7 2-1445094-7 1445098-8 2-1445098-8
1445086-6 2-1445086-6 1445090-7 2-1445090-7 1445094-8 2-1445094-8 1445098-9 2-1445098-9
1445086-7 2-1445086-7 1445090-8 2-1445090-8 1445094-9 2-1445094-9 1-1445098-0 3-1445098-0
1445086-8 2-1445086-8 1445090-9 2-1445090-9 1-1445094-0 3-1445094-0 1-1445098-1 3-1445098-1
1445086-9 2-1445086-9 1-1445090-0 3-1445090-0 1-1445094-1 3-1445094-1 1-1445098-2 3-1445098-2
1-1445086-0 3-1445086-0 1-1445090-1 3-1445090-1 1-1445094-2 3-1445094-2 1445099-2 2-1445099-2
1-1445086-1 3-1445086-1 1-1445090-2 3-1445090-2 1445095-2 2-1445095-2 1445099-3 2-1445099-3
1-1445086-2 3-1445086-2 1445091-2 2-1445091-2 1445095-3 2-1445095-3 1445099-4 2-1445099-4
1445087-2 2-1445087-2 1445091-3 2-1445091-3 1445095-4 2-1445095-4 1445099-5 2-1445099-5
1445087-3 2-1445087-3 1445091-4 2-1445091-4 1445095-5 2-1445095-5 1445099-6 2-1445099-6
1445087-4 2-1445087-4 1445091-5 2-1445091-5 1445095-6 2-1445095-6 1445099-7 2-1445099-7

1445087-5 2-1445087-5 1445091-6 2-1445091-6 1445095-7 2-1445095-7 1445099-8 2-1445099-8
1445087-6 2-1445087-6 1445091-7 2-1445091-7 1445095-8 2-1445095-8 1445099-9 2-1445099-9
1445087-7 2-1445087-7 1445091-8 2-1445091-8 1445095-9 2-1445095-9 1-1445099-0 3-1445099-0
1445087-8 2-1445087-8 1445091-9 2-1445091-9 1-1445095-0 3-1445095-0 1-1445099-1 3-1445099-1
1445087-9 2-1445087-9 1-1445091-0 3-1445091-0 1-1445095-1 3-1445095-1 1-1445099-2 3-1445099-2
1-1445087-0 3-1445087-0 1-1445091-1 3-1445091-1 1-1445095-2 3-1445095-2 1445100-2 2-1445100-2
1-1445087-1 3-1445087-1 1-1445091-2 3-1445091-2 1445096-2 2-1445096-2 1445100-3 2-1445100-3
1-1445087-2 3-1445087-2 1445092-2 2-1445092-2 1445096-3 2-1445096-3 1445100-4 2-1445100-4
1445088-2 2-1445088-2 1445092-3 2-1445092-3 1445096-4 2-1445096-4 1445100-5 2-1445100-5
1445088-3 2-1445088-3 1445092-4 2-1445092-4 1445096-5 2-1445096-5 1445100-6 2-1445100-6
1445088-4 2-1445088-4 1445092-5 2-1445092-5 1445096-6 2-1445096-6 1445100-7 2-1445100-7
1445088-5 2-1445088-5 1445092-6 2-1445092-6 1445096-7 2-1445096-7 1445100-8 2-1445100-8
1445088-6 2-1445088-6 1445092-7 2-1445092-7 1445096-8 2-1445096-8 1445100-9 2-1445100-9
1445088-7 2-1445088-7 1445092-8 2-1445092-8 1445096-9 2-1445096-9 1-1445100-0 3-1445100-0
1445088-8 2-1445088-8 1445092-9 2-1445092-9 1-1445096-0 3-1445096-0 1-1445100-1 3-1445100-1
1445088-9 2-1445088-9 1-1445092-0 3-1445092-0 1-1445096-1 3-1445096-1 1-1445100-2 3-1445100-2
1-1445088-0 3-1445088-0 1-1445092-1 3-1445092-1 1-1445096-2 3-1445096-2 1445101-2 2-1445101-2
1-1445088-1 3-1445088-1 1-1445092-2 3-1445092-2 1445097-2 2-1445097-2 1445101-3 2-1445101-3
1-1445088-2 3-1445088-2 1445093-2 2-1445093-2 1445097-3 2-1445097-3 1445101-4 2-1445101-4
1445089-2 2-1445089-2 1445093-3 2-1445093-3 1445097-4 2-1445097-4 1445101-5 2-1445101-5
1445089-3 2-1445089-3 1445093-4 2-1445093-4 1445097-5 2-1445097-5 1445101-6 2-1445101-6
1445089-4 2-1445089-4 1445093-5 2-1445093-5 1445097-6 2-1445097-6 1445101-7 2-1445101-7
1445089-5 2-1445089-5 1445093-6 2-1445093-6 1445097-7 2-1445097-7 1445101-8 2-1445101-8
1445089-6 2-1445089-6 1445093-7 2-1445093-7 1445097-8 2-1445097-8 1445101-9 2-1445101-9
1445089-7 2-1445089-7 1445093-8 2-1445093-8 1445097-9 2-1445097-9 1-1445101-0 3-1445101-0
1445089-8 2-1445089-8 1445093-9 2-1445093-9 1-1445097-0 3-1445097-0 1-1445101-1 3-1445101-1
1445089-9 2-1445089-9 1-1445093-0 3-1445093-0 1-1445097-1 3-1445097-1 1-1445101-2 3-1445101-2
1-1445089-0 3-1445089-0 1-1445093-1 3-1445093-1 1-1445097-2 3-1445097-2
1-1445089-1 3-1445089-1 1-1445093-2 3-1445093-2 1445098-2 2-1445098-2
220
Soft Shell
Part Number Index

Note: This index lists all cataloged parts Part No. Page Part No. Page Part No. Page
by base no. only. Complete part nos.
(with prefixes and/or suffixes) are shown 172334 85, 88 179847 61, 79 350201 166, 212
on the page(s) indicated. 172335 85, 87 179848 61, 80 350209 153, 161
172336 85, 87 179849 61, 80 350210 153, 161
172337 85, 87 179861 61, 75, 77 350211 154, 161, 163
Part No. Page 172338 85, 87 179862 61, 76-77 350212 153, 161
60617 155 172339 85, 87 179938 61, 75, 77 350213 153, 161
60618 155 172340 85, 88 179939 61, 75, 77 350214 153, 161
60619 155 172341 85, 88 179944 61 350218 172, 181, 213
60620 155 172342 85, 88 179945 61 350219 153, 161
60842 155 172343 85, 87 193796 201 350220 153, 161
60843 155 172344 85, 87 193797 201 350344 167
61085 203, 213 172807 85, 89 193839 201 350345 167
61086 203, 213 172808 85, 89 193841 201 350346 167
61116 155, 214 172809 85, 89 193842 201 350347 167
61117 155, 214 172971 86 194002 202 350373 116
61118 155, 214 173924 184, 199 194009 202 350374 116
61173 155 173925 184, 199 194010 202 350375 116
61174 155 173926 184, 199 194012 202 350376 116
Part Number Index

61233 203, 213 173956 85 194013 202 350377 116
61234 203, 213 173957 85, 89 194014 202 350378 116
61250 213 173958 85 194017 202 350379 116
61251 213 174552 154, 164 194018 202 350380 116
61252 213 174670 86 200821 156 350388 166
61253 213 177898 60, 62, 71 306088 14 350389 166
61314 155, 212 177899 60, 62, 71 316061 60, 78 350390 166
61320 156 177900 60, 63, 71 316062 60, 78 350391 166
61518 156 177901 60, 63, 71 316063 60, 78 350415 145, 212
61527 156, 212 177902 60, 63, 71 316086 10, 12, 14 350416 145, 212
61626 166, 212 177903 60, 64, 71 316087 10, 12, 14 350417 145, 212
61627 166, 212 177904 60, 64, 71 316088 10, 12, 14 350418 145, 212
106527 126 177905 60, 64, 71 316089 10, 12, 14 350422 153, 161
106528 126, 212 177906 60, 67, 71 316090 10, 12, 14 350423 153, 161
106529 126, 212 177907 60, 67, 71 316091 10, 12, 14 350424 154, 161, 163
171636 213 177908 60, 68, 71 316092 10, 12, 14 350425 153, 161
171637 213 177909 60, 68, 71 316094 10, 12, 14 350426 153, 161
171638 86 177911 60, 69, 71 316221 16 350427 153, 161
171639 86 177912 60, 69, 71 316222 16 350428 171, 182
172156 85, 87 177913 60, 70-71 316223 16 350429 171, 182
172157 85, 87 177914 61, 211 316224 16 350430 171, 182
172158 85, 87 177915 61, 211 316225 16 350431 171, 182
172159 85, 87 177916 61, 211 316226 16 350432 171, 182
172160 85, 87 177917 61, 211 316227 16 350433 171, 182
172161 85, 88 177918 60, 71 316299 72 350434 171, 182
172162 85, 88 177919 60, 71 316398 12 350444 155
172163 85, 88 177920 60, 71 316399 12 350522 116
172164 85, 87, 92 177921 60, 71 316400 12 350523 116
172165 85, 87, 90, 92, 103, 105 179463 60, 65, 71 316401 12 350524 116
172166 85, 87, 90, 92, 103, 105 179464 60, 65, 71 316454 94 350536 172, 181, 213
172167 85, 87, 90-92, 103-105 179465 60, 66, 71 316455 94 350537 172, 213
172168 85, 87, 90-92, 103-105 179466 60, 66, 71 316501 60, 62, 71 350538 172, 213
172169 85, 88, 90-92, 103-105 179467 60, 66, 71 316502 60, 67, 71 350539 153, 158, 161
172170 85, 88, 90-92, 103-105 179592 61 316768 60, 62, 71 350540 153, 158, 161
172171 85, 88, 90-92, 103-105 179593 61 316769 60, 65, 71 350541 153, 158, 161
172233 85, 87 179594 61 316770 60, 71 350542 153, 161
172234 85, 87 179595 61 350020 116 350543 154, 158, 161
172327 85, 87 179838 61, 72 350021 116 350544 154, 158, 161
172328 85, 87 179839 61, 72 350022 116 350547 172, 181
172329 85, 87 179840 61, 73 350073 156 350550 172, 181
172330 85, 87 179841 61, 73 350074 156 350551 172
172331 85, 87 179843 61, 74 350078 155, 212 350552 172
172332 85, 88 179844 61, 74 350079 155, 212 350557 155, 212
172333 85, 88 179846 61, 79 350200 166, 212 350558 155, 212
221
Soft Shell
Part Number Index (Continued)
Part No. Page Part No. Page Part No. Page Part No. Page
350561 172, 212 350779 171, 174, 182-185, 350990 171, 183 480705 171, 174
350570 172, 212 197-200 350991 171, 183 480706 171, 174, 182-183
350576 153, 162 350780 171, 174 350992 171, 183 480707 171, 174
350577 153, 162 350781 171, 174 353891 60, 78 480708 171, 174, 182-183
350578 153, 162 350782 171, 174 380935 116 480709 171, 174
350579 153, 162 350783 171, 174 380936 116 480710 171, 174, 182-183
350582 171, 182 350784 171, 174 380937 116 480711 171, 174
350583 171, 182 350786 171, 182, 191, 197 380991 153, 161 480720 153,158,161
350584 171, 182 350787 171, 182, 191, 197 380999 153, 161 480721 153,158,161
350585 171, 182 350789 171, 182, 191, 197 480270 153, 158, 160-161 480722 158, 161
350586 171, 182 350790 171, 182, 191, 197 480271 153, 160 480763 171, 174, 182-183, 185
350587 171, 182 350792 171, 182, 191, 197 480273 153, 159 480764 171, 174
350588 171, 182 350793 171, 182, 191, 197 480274 153, 159 480772 154
350589 175 350809 171, 174, 182-183, 480275 153, 159 640309 172
185, 197-198
350590 173 480276 153, 159, 162 640310 172
350810 171, 174, 193
350591 112 480277 153, 159, 162 640347 172
350811 173
350628 55, 211 480278 153, 159, 162 640391 55, 211
350812 173
350629 55, 211 480283 153, 158, 160-161 640392 55, 211
350824 171, 183, 191, 198
Part Number Index
350638 155 480284 153, 160 640415 173

350825 171, 183, 191, 198
350639 155 480285 153, 158, 160-161 640466 171, 182
350826 171, 183, 191, 198
350641 153, 162 480286 153, 160 640467 171, 183
350827 171, 183, 191, 198
350642 153, 162 480287 153, 160-161 640497 105, 112
350828 171, 183, 191, 198
350643 153, 162 480288 153, 160 640498 105, 112
350829 171, 183, 191, 198
350644 153, 162 480303 153, 157, 161, 163 640499 105, 112
350830 171, 183, 191, 198
350654 173, 181, 213 480304 153, 159 640500 105, 112
350831 171, 183, 191, 198
350669 173, 181 480305 153, 157, 159 640501 105, 112
350832 171, 183, 191, 198
350687 173, 181, 213 480318 153, 157, 161, 163 640502 105, 112
350833 171, 183, 191, 198
350689 172 480319 153, 157 640503 105, 112
350834 171, 183, 191, 198
350690 172 480323 153, 159 640504 105, 112
350835 171, 183, 191, 198
350699 173, 213 480324 153, 159, 162 640505 105, 112
350836 171, 183, 191, 198
350700 173, 213 480339 153, 158 640506 105, 112
350837 171, 183, 191, 198
350705 173, 181 480340 153, 158 640507 105, 107
350838 112
350706 173 480345 153, 158 640508 105, 107
350848 185
350707 173 480349 153, 157 640509 105, 107
350849 185
350711 171, 182, 191, 197 480350 153, 157 640510 105, 107
350851 172, 212
350712 171, 182, 191, 197 480351 153, 157 640511 105, 108
350865 171, 174
350713 171, 182, 191, 197 480387 153, 157 640512 105, 108
350866 171, 174
350714 171, 182, 191, 197 480388 153, 157 640513 105, 108
350867 171, 174
350715 171, 174, 182-183, 480393 153, 157 640514 105, 108
197-198 350871 173
480400 153, 157 640515 105, 108
350720 171, 174, 182-183, 350873 172, 213
480401 153, 157 640516 105, 108
197-198 350874 172, 213
480424 154, 157, 165, 163-164 640517 105, 107, 112
350732 171, 182, 191, 197 350877 173
480425 154, 159 640518 105, 107, 112
350735 171, 174, 182-183, 350918 172
197-198 480426 154, 157, 165, 162-163 640519 105, 107, 112
350919 172
350736 171, 174, 182-183, 480438 153, 160-161 640520 105, 107, 112
350922 172, 213
197-198 480439 153, 160 640521 105, 108, 112
350923 172, 213
350737 171, 182, 191, 197 480498 153, 157 640522 105, 108, 112
350924 172, 212
350738 171, 182, 191, 197 480510 166 640523 105, 108, 112
350925 172, 212
350742 171, 182, 191, 197 480512 166 640524 105, 108, 112
350942 171, 183, 191, 200
350759 171, 183 480585 166 640525 105, 108, 112
350943 171, 183, 191, 200
350760 171, 183 480586 166 640526 105, 108, 112
350944 171, 183, 191, 200
350761 171, 183 480594 116 640545 112
350945 171, 183, 191, 200
350762 171, 183 480634 116 640579 112
350948 171, 185
350763 171, 183 480672 167 640580 112
350949 171, 185
350764 171, 183 480673 167 640581 171, 174, 182-183, 185
350967 106, 205
350765 171, 183 480698 171, 174, 182-184 640582 171, 174, 182, 185
350968 106, 205
350766 171, 174, 182-185, 480699 171, 174 640583 171, 185
197-200 350969 106, 205
480700 171, 174, 182-184 640584 171, 185
350767 171, 174 350986 171, 183
480701 171, 174 640585 171, 174, 182, 185
350777 171, 174, 182-185, 350987 171, 183
197-200 480702 171, 174, 182-185 640586 171, 174, 182, 185
350988 171, 183
350778 171, 174 480703 171, 174 640587 171, 185
350989 171, 183
480704 171, 174, 182-183 640713 180, 196
222
Soft Shell
640714 180, 196 643415 171, 183 770050 195 770194 192, 213
640715 180, 196 643416 171, 183, 191, 198 770051 195 770210 173, 213
640716 180, 196 643423 171, 183 770052 195 770232 163
640717 180, 196 643424 171, 183, 191, 198 770053 195 770233 163
640718 180, 196 643425 171, 183 770054 195 770234 173, 213
640719 176 643426 171, 183, 191, 198 770055 195 770246 192
640720 176 643428 171, 183, 191, 198 770056 195 770247 192
640721 176 643429 171, 183 770057 195 770248 192
640722 176 643430 171, 183, 191, 198 770058 195 770249 192
640723 176 643488 153, 163 770063 146 770250 192
640724 176 643585 176 770064 146 770251 192
640900 171, 182, 191, 197 643749 182 770065 146 770252 192
640901 171, 183, 191, 198 770003 192, 213 770066 146 770253 192
641083 171 770004 192, 213 770068 146 770254 192
641294 106, 205 770005 192, 213 770069 146 770255 192
641300 112 770006 192, 213 770070 146 770262 171, 183
641737 154, 163 770007 192, 213 770071 146 770264 146
641763 176 770008 192, 213 770073 146 770266 146
Part Number Index

641775 176 770009 192, 213 770074 146 770269 148
641776 180, 196 770010 192, 213 770075 146 770272 182
641777 176 770011 192, 213 770076 146 770274 56
641778 176 770012 192, 213 770077 146 770275 56
641825 171, 182 770016 194-195, 185, 191, 770078 146 770276 148
641828 171, 182 193, 195, 197-198 770083 146 770277 56
641831 171, 182 770017 194-195, 191, 193, 770084 146 770278 56
195, 197-201
641832 171, 182 770085 146 770319 195
770018 194-195, 191, 193,
641945 180, 196 195, 197-201 770086 146 770320 195
641963 171, 182 770019 194-195, 191, 193, 770087 146 770326 56
641964 171, 182, 191, 197 195, 197-1201 770088 146 770329 148
641965 171, 182 770020 194-195, 191, 194-195, 770089 146 770330 148
197-198, 201
641966 171, 182, 191, 197 770090 146 770331 56
770021 194-195, 191, 194-195,
641967 171, 182 197-198, 201 770091 146 770332 56
641968 171, 182, 191, 197 770022 194-195, 191, 194-195, 770092 146 770333 56
641969 171, 182 197-198, 201 770093 146 770334 56
641970 171, 182, 191, 197 770023 194-195, 191, 194-195, 770094 146 770335 56
197-198, 201
641971 171, 182 770095 146 770336 148
770024 191, 193, 195, 201
641972 171, 182, 191, 197 770096 146 770337 148
770025 191, 193, 195, 201
641973 171, 182 770097 146 770338 148
770026 191, 193, 195, 201
641974 171, 182, 191, 197 770098 146 770339 148
770027 191, 194-195, 201
641975 171, 182 770099 146 770340 56
770028 191, 194-195, 201
641976 171, 182, 191, 197 770100 146 770341 56
770029 191, 194-195, 201
643030 180, 196 770101 146 770342 56
770030 191, 194-195, 201
643182 176 770102 146 770343 56
770031 195
643226 171, 183, 191, 200 770103 146 770351 182
770032 195
643228 171, 183, 191, 200 770105 146 770353 56
770033 195
643230 171, 183, 191, 200 770106 146 770354 56
770034 195
643232 171, 183, 191, 200 770107 146 770355 56
770035 195
643234 171, 185 770108 146 770356 56
770036 195
643235 185 770143 171, 182 770360 148
770037 195
643236 171, 185 770144 145 770361 148
770038 195
643237 185 770145 145 770364 145, 149
770039 195
643313 176 770146 145 770365 145, 149
770040 195
643314 176 770147 145 770372 148
770041 195
643405 171, 182 770156 154, 163 770373 148
770042 195
643406 171, 182, 191, 197 770166 85, 90, 103, 107 770377 180, 196
770043 195
643407 171, 182 770170 85, 90, 103, 107 770383 145, 212
770044 195
643408 171, 182 770174 85, 90, 103, 107 770385 145, 212
770045 195
643410 171, 182 770178 85, 90, 103, 107 770416 192
770046 195
643411 171, 183 770182 85, 90, 103, 107 770419 56
770047 195
643412 171, 183, 191, 198 770186 85, 90, 103, 107 770421 171, 174
770048 195
643413 171, 183 770190 85, 90, 103, 107 770424 149
770049 195
643414 171, 183, 191, 198 770193 192, 213 770425 149
223
Soft Shell
770426 56 770973 85, 91, 105, 107 794189 101, 107 794250 101, 107
770427 56 770974 85, 91, 105, 107 794190 90-92, 99, 101-102, 107 794251 101, 107
770428 56 770983 53, 55 794191 101, 107 794252 101, 107
770429 56 770985 85, 96 794192 90-91, 100-101, 105, 107 794253 101, 107
770433 56 770986 85, 96 794193 101, 107 794254 101, 107
770441 56 770987 85, 96 794194 90-91, 100-102, 107 794255 101, 107
770442 56 770988 85, 96 794195 101, 107 794256 101, 107
770443 56 770994 185 794196 90-91, 100-105, 107 794257 101, 107
770450 145, 149 770997 154, 162 794197 101, 107 794258 101, 107
770451 145, 149 794000 106, 205 794198 90, 92, 100-101, 794259 101, 107
770452 145, 149 794001 112 105, 107 794260 101, 107
770453 145, 149 794012 153, 158 794199 101, 107 794261 101, 107
770512 192 794015 146 794200 90-91, 100-102, 107 794262 101, 107
770526 154 794016 55 794201 101, 107 794263 101, 107
770529 145, 212 794017 55 794202 90, 92, 100-101, 794264 101, 107
105, 107
770530 145, 212 794018 55 794265 101, 107
794203 101, 107
770579 85, 88, 90-93, 103-106 794019 55 794266 101, 107
794204 90-91, 100-102, 107
770580 85, 88, 90-93, 103-106 794036 154, 163 794267 101, 107
794205 101, 107
Part Number Index
770581 85, 88, 90, 92, 103, 105 794040 85, 90, 103, 107 794268 101, 107
794206 90, 92, 100-101,
770582 85, 88, 90, 92, 103, 105 794046 55, 211 105, 107 794269 179
770583 85, 88, 90, 92, 103, 105 794058 86 794207 101, 107 794270 179
770584 85, 88, 90, 92, 103, 105 794059 86 794208 90, 92, 100-101, 794271 179
770585 85, 88, 90, 92, 103, 105 794061 167 105, 107 794272 179
770586 85, 88, 90, 92, 103, 105 794065 85, 90, 103, 107 794209 101, 107 794273 179
770587 85, 88, 90, 92, 103, 105 794066 85, 90, 103, 107 794210 90, 92, 100-101, 794274 179
105, 107
770621 85, 90, 103, 107 794067 85, 90, 103, 107 794275 179
794211 101, 107
770672 172 794068 85, 90, 103, 107 794276 179
794212 90, 92, 100-101,
770673 172 794069 85, 90, 103, 107 105, 107 794277 179
770743 85, 90, 103, 107 794070 85, 90, 103, 107 794213 101, 107 794278 179
770771 148 794071 85, 90, 103, 107 794214 90, 92, 100-101, 794279 179
770782 146 794072 85, 90, 103, 107 105, 107 794280 179
770783 149 794073 85, 90, 103, 107 794215 101, 107 794281 179
770784 149 794074 85, 90, 103, 107 794216 100, 211 794282 179
770785 149 794075 85, 90, 103, 107 794217 100, 211 794285 162
770810 149 794076 85, 90, 103, 107 794218 100, 211 794287 154, 162
770827 154, 157, 163 794077 85, 90, 103, 107 794219 100, 211 794302 128
770829 154, 162-163 794078 85, 90, 103, 107 794220 100, 211 794303 128
770834 85, 211 794079 85, 90, 103, 107 794221 100, 211 794304 128
770835 85, 211 794096 171, 174 794222 100, 211 794305 129
770842 146 794103 55, 211 794223 100, 211 794306 129
770843 146 794105 85, 91, 105, 107 794224 100 794307 130
770846 154, 163 794106 85, 91, 105, 107 794225 100 794308 130
770858 85, 90, 103, 107 794107 85, 91, 105, 107 794226 100 794309 131
770859 85, 90, 103, 107 794108 85, 91, 105, 107 794227 100 794310 131
770872 85, 90, 103, 107 794116 214 794228 100 794311 132
770872 97 794117 214 794229 100 794312 132
770873 85, 90, 103, 107 794118 214 794230 100 794313 133
770874 85, 90, 103, 107 794120 153, 163 794231 100 794325 85, 90, 104, 107
770875 85, 90, 103, 107 794132 154, 157 794236 154, 161 794326 85, 90, 104, 107
770876 85, 90, 103, 107 794138 126, 212 794237 101, 107 794327 85, 90, 104, 107
770892 146 794139 126, 212 794238 101, 107 794328 85, 90, 104, 107
770901 86, 96, 211 794140 126, 212 794239 101, 107 794329 85, 90, 104, 107
770902 86, 96, 211 794141 126 794240 101, 107 794330 85, 90, 104, 107
770903 86, 96, 211 794142 126 794241 101, 107 794349 128
770904 86, 96, 211 794143 126 794242 101, 107 794350 128
770966 85, 91, 105, 107 794184 90, 92, 101, 103, 794243 101, 107 794351 128
770967 85, 91, 105, 107 105, 107 794244 101, 107 794352 129
770968 85, 91, 105, 107 794185 101, 107 794245 101, 107 794353 129
770969 85, 91, 105, 107 794186 90, 92, 101, 103, 794246 101, 107 794354 130
105, 107
770970 85, 91, 105, 107 794247 101, 107 794355 130
794187 101, 107
770971 85, 91, 105, 107 794248 101, 107 794356 131
794188 90-92, 99, 101-102, 107
770972 85, 91, 105, 107 794249 101, 107 794357 131
224
Soft Shell
794358 132 794538 171 794707 171 917696 10, 12-13
794359 132 794540 128 794714 177 917697 10, 12-13
794360 133 794542 127 794715 177 917698 10, 12
794369 101 794543 128 794716 177 917699 10, 12
794370 94 794545 171 794727 171 917700 10, 12
794374 85, 92 794546 171 794758 96 917701 10, 12
794380 53, 55 794550 127 794760 177 917702 10, 12
794406 86 794576 121, 206 794761 177 917703 10, 12
794407 86 794577 127 794762 177 917704 10, 12
794412 214 794578 121, 206 794772 96 917705 10, 12
794413 214 794579 127 794772 97 917706 10, 12
794415 132 794588 133 794781 85, 96 917707 10, 12
794418 126,212 794589 133 794781 97 917708 10, 12
794421 126 794590 133 794805 85, 96 917709 10, 12
794423 94 794594 127 794805 97 917722 10, 16
794429 131 794598 127 794814 171 917723 10, 16
794432 85, 90, 104, 107 794606 19-22, 211 794815 171 917724 10, 16
794448 133 794606 20 794821 85, 96 917725 10, 16
Part Number Index

794449 133 794607 19-22, 211 794821 97 917726 10, 16
794453 130 794608 19, 22, 211 794824 96 917727 10, 16
794454 131 794609 19, 22, 211 794824 97 917728 10, 16
794455 132 794610 19-22 794851 171 917729 10, 16
794466 128 794610 20 794863 171 917730 10, 16
794467 128 794611 19-22 794894 85, 96 917731 10, 16
794468 129 794611 20 794894 97 917732 10, 16
794469 129 794612 19, 22 794895 85, 96 917733 10, 16
794470 130 794613 19, 22 794896 85, 96 917745 61, 79
794471 132 794615 19, 28 794899 171 917746 79
794472 133 794616 19, 27 794900 171 917747 80
794484 128 794617 19, 21, 24, 34-37, 794901 171 917764 12, 14, 205
794485 128 43-47 794911 191 917765 12, 14, 205
794486 129 794618 21, 44 794912 191 917780 10, 15
794487 129 794619 21, 44 794939 85, 96 917781 10, 15
794488 130 794620 21, 44 794940 85, 96 917782 10, 15
794489 130 794621 21, 46 794941 85, 96 917783 10, 15
794490 131 794622 21, 46 794942 85, 96 917784 10, 15
794491 131 794623 21, 46 794953 122 917785 10, 15
794492 132 794624 21, 45 794954 122 917786 10, 15
794493 132 794625 21, 45 794955 114, 206 917787 10, 15
794494 133 794626 21, 45 794956 114, 206 917788 10, 15
794507 133 794627 21, 47 794957 114, 206 917789 10, 15
794508 133 794628 21, 47 794958 114, 206 917790 10, 15
794509 133 794629 21, 47 794991 180 917791 10, 15
794510 133 794630 21, 34 794992 180 917845 61,73
794511 133 794631 21, 34 794993 180 917894 15
794512 133 794632 21, 34 794994 180 917895 15
794513 133 794633 21, 36 794995 96 917896 15
794514 133 794634 21, 36 797607 20 917897 15
794515 133 794635 21, 36 917353 61, 81 917898 15
794516 133 794636 21, 37 917354 61, 76-77 917899 15
794526 133 794637 21, 37 917683 12-13, 205 917900 15
794527 133 794638 21, 37 917684 12-13, 205 926302 171, 174
794528 133 794657 126 917686 10, 12-13 926307 171, 174
794529 133 794677 21, 43 917687 10, 12-13 926308 171, 174
794530 133 794678 21, 43 917688 10, 12-13 926309 171, 174
794531 133 794679 21, 43 917689 10, 12-13 1375618 126-127
794532 133 794680 21, 35 917690 10, 12-13 1376294 136
794533 133 794681 21, 35 917691 10, 12-13 1376347 137, 212
794534 133 794682 21, 35 917692 10, 12-13 1376348 137, 212
794535 171 794683 167 917693 10, 12-13 1376382 136, 138, 140
794536 171 794699 167 917694 10, 12-13 1376383 136, 138, 140
794537 171 794700 166 917695 10, 12-13 1376384 136, 138, 140
225
Soft Shell
1376385 136, 138, 140 1445087 20, 33 1586038 123 1586522 153, 161
1376386 136, 139, 141 1445088 20, 38 1586039 123 1586524 153, 161
1376387 136, 139, 141 1445089 20, 39 1586040 123 1586525 154, 161
1376388 136-138, 140 1445090 20, 40 1586041 123 1586526 153, 161
1376389 136-138, 140 1445091 20, 41 1586042 123 1586528 153, 161
1376390 136-138, 140 1445092 20, 42 1586043 123 1586529 153, 161
1376391 136-138, 140 1445093 20, 30 1586044 123 1586530 153, 161
1376392 136, 139, 141 1445094 20, 31 1586101 121 1586532 153, 161
1376393 136, 139, 141 1445095 20, 32 1586102 121 1586534 154, 161
1376394 136-139 1445096 20, 33 1586103 121 1586536 154, 161
1376395 136-139 1445097 20, 38 1586104 121 1586539 162
1376396 136-138 1445098 20, 39 1586105 121 1586544 153, 161
1376397 136-138 1445099 20, 40 1586106 121 1586546 153, 161
1376421 136, 138, 140 1445100 20, 41 1586305 167 1586585 124
1376437 140 1445101 20, 42 1586314 121 1586586 124
1376439 140 1565079 50, 211 1586315 121 1586587 124
1376440 140 1565080 50, 211 1586316 121 1586588 124
1376441 140 1565081 51 1586317 121 1586627 161
Part Number Index
1376442 140 1565082 51 1586359 97 1604210 178

1376443 140 1565083 52 1586359 96 1604254 178
1376444 140 1565084 52 1586362 96 1604256 178
1445022 19-20, 23, 30-33, 38-42 1565085 51 1586362 97 1604941 178
1445048 19, 26 1565086 51 1586404 96 1612334 50, 211
1445049 19, 25 1565087 52 1586489 128-133 1612335 50, 211
1445050 20, 30 1565088 52 1586490 128-133 1903486 60, 78
1445051 20, 31 1586000 122 1586491 128-133 1903487 60, 78
1445052 20, 32 1586017 122 1586492 128-133 1903720 60 ,66
1445053 20, 33 1586018 122 1586493 128-133 1939343 60 ,73, 78
1445054 20, 38 1586019 122 1586494 128-133 1939344 60
1445055 20, 39 1586022 121 1586495 128-133 2029030 20, 29
1445056 20, 40 1586023 121 1586496 128-133 2029047 20, 29
1445057 20, 41 1586024 121 1586512 153, 161 2029056 97
1445058 20, 42 1586025 121 1586514 153, 161 2029058 97
1445084 20, 30 1586026 121 1586515 154, 161 2029102 20, 29
1445085 20, 31 1586027 121 1586518 153, 161 2029104 20, 29
1445086 20, 32 1586037 123 1586520 153, 161
226
Soft Shell
Tooling Part Number Index
58074 163, 206 91502 22, 209-210 455822 112, 206 567309 166, 212
58373 166, 210 91504 155, 210 455830 112, 155, 206 567337 145, 212
58374 166, 210 91506 172-173, 192,210 457306 116 567418 86, 100, 211
58380 172, 192, 210 91508 172-173, 192,210 465644 155, 206 567902 211
58382 192, 201, 206 91510 172-173, 192,210 466320 155-156, 172-173, 567913 213
58439 172, 192, 210 91512 155-156, 210 212-213 567914 213
58514 210 91515 155, 210 466351 112, 211 567959 126-127, 212
58631 203, 210 91522 86, 96, 100, 210 466352 112, 211 567960 126-127, 212
58632 203, 210 91526 112, 210 466426 155, 212 587309 212
65780 209-210 91528 155 466462 203, 213 680307 126-127, 212
69710 166, 172, 192, 210 91529 86, 96, 100, 210 466588 172, 213 680308 126-127, 212
82276 210 91534 112, 210 466597 172-173, 213 680350 126, 212
90247 166 91536 86 466616 172, 212 680582 86, 100, 211
90546 210 91552 210 466656 145, 212 680854 100, 211
90547 210 91567 61, 210 466686 55, 211 680893 22, 211
90548 210 91569 61, 210 466878 145, 212 680894 22, 211
90574 210 91594 100, 210 466913 211 687763 155, 172-173,
90575 210 188688 126 466917 212-213 181, 212-213
90714 126,210 189727 86, 206 466920 212-213 687765 155, 212
90717 86, 100,210 231894 163, 206 466922 212 687898 172-173, 213
90758 210 231920 163, 206 466955 211 687926 55, 211
Tooling Part Number Index

90759 210 234603 12, 210 466959 212 687996 203, 206
90760 210 234604 12, 210 466986 211 691458 181
90869 55, 210 234605 12 466989 213 794381 22
90870 55, 210 234912 61 466990 211 843996 207
90871 145,210 234914 61 567066 86, 96, 100, 211 854040 22, 211
90872 145, 210 305183 155, 206 567067 86, 96, 211 1385194 22, 211
91002 55, 86, 145, 172, 318831 55, 206 567211 192, 213 1385377 120, 212
181, 192, 203, 206 318837 145, 206 567212 192, 213 1385448 120, 212
91085 163, 206 318845 166, 206 567213 192, 213 1385817 120
91112 163, 206 318851 172, 181, 192, 567214 192, 213 1586343 22
91387 120, 210 201, 206 567216 173, 213 1586344 172, 206
91388 120, 210 354500 207 567251 211 1586700 50, 210
91500 172-173, 181, 356114 201 567252 192, 213 1596277
192, 210 356337 201 567273 145, 212
91501 22, 209-210 356500 208 567306 166, 212
227
Soft Shell
Engineering Notes
228
Soft Shell
Engineering Notes
229
Soft Shell
Engineering Notes
230
Global Contacts
Americas
Argentina – Buenos Aires Canada – Toronto Mexico – Mexico City For Latin/South American
Phone: +54-11-4733-2200 Phone: +905-475-6222 Phone: +52-55-1106-0800 Countries not shown
Fax: +54-11-4733-2211 Fax: +905-474-5520 +01-800-733-8926 Phone: +54-11-4733-2015
Product Information Center: Fax: +52-55-1106-0901 Fax: +54-11-4733-2083
Brasil – São Paulo (Technical Support)
Phone: +55-11-3611-1311 Phone: +905-470-4425 United States – Harrisburg, PA
Fax: +55-11-3611-0397 Fax: +905-474-5525 Phone: +717-564-0100
Fax: +717-986-7575
Colombia – Bogota Product Information Center:
Phone: +57-1-231-9398 (Technical Support)
Fax: +57-1-660-0206 Phone: +800-522-6752
Fax: +717-986-7575
Asia/ Pacific
Australia – Sydney Japan – Toyko New Zealand – Auckland Singapore – Singapore
Phone: +61-2-9554-2600 Phone: +81-44-844-8111 Phone: +64-9-634-4580 Phone: +65-6482-0311
Fax: +61-2-9502-2556 Fax: +81-44-812-3207 Fax: +64-9-634-4586 Fax: +65-6482-1012
Product Information Center: Product Information Center:
(Technical Support) (Technical Support) Philippines – Makati City Thailand – Bangkok
Phone: +61-2-9840-8200 Phone: +81-44-844-8013 Phone: +632-848-0171 Phone: +66-2-955-0500
Fax: +61-2-9634-6188 Fax: +81-44-812-3200 Fax: +632-867-8661 Fax: +66-2-955-0505
India – Bangalore Korea – Seoul People’s Republic of China Vietnam and Indochina –
Phone: +91-80-285-40800 Phone: +82-2-3415-4500 Hong Kong Ho Chi Minh City
Fax: +91-80-285-40820 Fax: +82-2-3486-3810 Phone: +852-2735-1628 Phone: +84-8 930-5546
Fax: +852-2735-0243 Fax: +84-8 930-3443
Indonesia – Jakarta Malaysia – Kuala Lumpur
Phone: +65-6482-0311 Phone: +60-3-78053055 Shanghai
Fax: +65-6482-1012 Fax: +60-3-78053066 Phone: +86-21-2407-1588
Fax: +86-21-2407-1599
Taiwan – Taipei
Phone: +886-2-8768-2788
Fax: +886-2-8768-2268
Europe/ Middle East/Africa

Austria – Vienna Germany – Bensheim Lithuania – Vilnius Spain – Barcelona
Phone: +43-1 90 5 60-0 Phone: +49-6251-133-0 Phone: +370-5-2131-402 Phone: +34-93-291-0330
Fax: +43-1 90 5 60-1333 Fax: +49-6251-133-1600 Fax: +370-5-2131-403 Fax: +34-93-201-7879
Product Information Center: Product Information Center:
(Technical Support) Netherlands – ’s-Hertogenbosch (Technical Support):
Belgium – Kessel-Lo
Phone: +49-6251-133-1999 Phone: +31-73-624-62-46 Phone: +34-93-291-0330
Phone: +32-16-35-23-00
Fax: +49-6251-133-1988 Fax: +31-73-621-23-65 Fax: +34-93-200-3779
Fax: +32-16-35-23-52
Product Information Center:
(Technical Support)
Bulgaria – Sofia Germany – Langen Sweden – Upplands Väsby
Phone: +31-73-6246-999
Phone: +359-2-971-2152 Phone: +49-6103-709-0 Phone: +46-8-50-72-50-00
Fax: +31-73-6246-998
Fax: +359-2-971-2153 Fax: +49-6103-709-1223 Fax: +46-8-50-72-50-01
Norway – Nesbru
Czech Republic – Kurim Germany – Speyer Phone: +47-66-77-8886 Switzerland – Steinach
Phone: +420-5-41-162-111 Phone: +49-6232-30-0 Fax: +47-66-77-8855 Phone: +41-71-447-0447
Fax: +420-5-41-162-223 Fax: +49-6232-30-2243 Fax: +41-71-447-0444
Poland – Warsaw
Germany - HTS Division – Neunkirchen Phone: +48-22-45-76-700 Turkey – Istanbul
Denmark – Glostrup Fax: +48-22-45-76-720
Phone: +45-43-480-452 Phone: +49-2247-305-0 Phone: +90-212-281-8181/2/3
Fax: +45-43-441-414 Fax: +49-2247-305-122 Fax: +90-212-281-8184
Romania – Bucharest
Phone: +40-21-311-3479/3596
Egypt – Cairo Greece – Athens Fax: +40-21-312-0574 Ukraine – Kiev
Phone: +20-2-29 04 281 Phone: +30-210-9370-396/397 Phone: +380-044-206-2265
Fax: +20-2-41 92 334 Fax: +30-210-9370-655 Russia – Moscow Fax: +380-044-206-2264
Phone: +7-495-926-5506/07/08/09
Hungary – Budapest Fax: +7-495-926-5505 United Kingdom – Swindon
Estonia – Tartu
Phone: +372-5138-274 Phone: +36-1-289-1000 Phone: +44-8706-080-208
Fax: +36-1-289-1010 Russia – St. Petersburg Fax: +44-1793-572-516
Fax: +372-7400-779 Phone: +7-812-718-8192 Product Information Center:
Ireland – Dublin Fax: +7-812-718-8193 (Technical Support)
Finland – Helsinki Phone: +353-1-820-3000 Freephone GB: 0800-267-666
Phone: +358-95-12-34-20 Fax: +353-1-820-9790 Slovenia – Ljubljana Phone: +44-8706-080-208
Fax: +358-95-12-34-250 Phone: +386-1561-3270 Fax: +44-208-420-8081
Israel – Yokneam Fax: +386-1561-3240
France – Cergy-Pontoise Phone: +972-4-959-0508
For Middle East/African Countries Not
Phone: +33-1-3420-8888 Fax: +972-4-959-0506
South Africa – Port Elizabeth Shown
Fax: +33-1-3420-8600 Phone: +2741-503-4500 Phone: +33-1-3420-8866
Product Information Center: Italy – Collegno (Torino)
Phone: +39-011-4012-111 Fax: +2741-581-0440 Fax: +33-1-3420-8300
(Technical Support)
Phone: +33-1-3420-8943 Fax: +39-011-4031116
Fax: +33-1-3420-8623
231
82181–7.5M–MS–FP–4-08 0G3B Tyco Electronics Corporation
Printed in the U.S.A. www.tycoelectronics.com
Catalog 82181
Revised 4-08
Soft Shell Pin and Socket Connectors
AMP Soft Shell Pin
and Socket Connectors
Tyco Electronics Corporation

Harrisburg, PA
tycoelectronics.com
82181–7.5M–MS–FP–4-08–2–0G3B

Eng CS 82181 Softshell Standard Density 0508 PDF

Uploaded by

Copyright:

Available Formats

Eng CS 82181 Softshell Standard Density 0508 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Eng CS 82181 Softshell Standard Density 0508 PDF

Uploaded by

Copyright:

Available Formats

Soft Shell

Pin and Socket Connectors AMP

5.0 mm Power Key Connectors (5.0 PKC) (Wire-to-Board)

.197 [5.00] Centerline

5.0 mm Power Key Connectors (5.0 PKC) (Wire-to-Board) (Continued)

Quick Reference Chart for Mating Part Numbers

Type B/Red 1-1376392-2 1376394-1 1-1376386-2

Note: Dimensions shown are metric.

5.0 mm Power Key Connectors (5.0 PKC) (Wire-to-Board) (Continued)

Material and Finish

Wire Range Receptacle Contact Applicator

Double Lock Plates

.197 [5.00] Centerline

Dimensions (Double Lock Plate) Double Lock Plate Applicable

5.0 mm Power Key Connectors (5.0 PKC) (Wire-to-Board) (Continued)

Material and Finish

Related Product Data

Plug Housing Part No. Applicable

Note: Dimensions shown are metric.

5.0 mm Power Key Connectors (5.0 PKC) (Wire-to-Board) (Continued)

Plug Housing (2 Rows)

Material and Finish

Related Product Data

.197 [5.00] Centerline

Note: Dimensions shown are metric.

5.0 mm Power Key Connectors (5.0 PKC) (Wire-to-Board) (Continued)

Vertical Header Assembly

Material and Finish

Related Product Data

Vertical Header Assy. Part No.

5.0 mm Power Key Connectors (5.0 PKC) (Wire-to-Board) (Continued)

Vertical Header Assembly

Material and Finish

Related Product Data

.197 [5.00] Centerline

Vertical Header Assy. Part No.

Note: Dimensions shown are metric.

.093 [2.36] Commercial Pin and Socket Connectors

.198 [5.03] Centerline

.093 [2.36] Commercial Pin and Socket Connectors (Continued)

can be carried in any given connector. 30 2.6 18 9.4

Termination Resistance/Contact Crimp Tensile Force

.093 [2.36] Commercial Pin and Socket Connectors (Continued)

Related Product Data Pin Socket

.198 [5.03] Centerline

Note: Phosphor bronze contacts should be used in high-temperature/humidity cycling applications.

Note: All part numbers are RoHS Compliant.

.093 [2.36] Commercial Pin and Socket Connectors (Continued)

Related Product Data Receptacle Plug

Receptacle Part Numbers

Plug Part Numbers

Note: All part numbers are RoHS Compliant.

.093 [2.36] Commercial Pin and Socket Connectors (Continued)

Housings 5 Circuit, In-Line

Related Product Data

Receptacle (Free-Hanging) Plug (Free-Hanging)

4, 6, 9, 12, and 15 Circuit, Matrix

.430 .535 ± .010

.630 1.000 ± .010