Scribd
Upload
338 views

Power System Protection - Part 07

Differential protection compares electrical quantities entering and leaving a protected zone. If the quantities are equal, no fault is present. It operates based on either current balance or voltage balance principles. Current balance differential protection compares currents measured by current transformers on both sides of a zone. An internal fault causes a difference between the currents, triggering operation. Voltage balance differential protection compares voltages induced in secondary windings connected in opposition; an internal fault causes a difference activating the relay. Percentage differential relays include operating and restraining windings. The restraining windings prevent operation for external faults while allowing operation for high resistance internal faults. Differential protection provides high sensitivity and selectivity with relatively high speed operation.

Uploaded by

shashikant yadav
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
338 views

Power System Protection - Part 07

Differential protection compares electrical quantities entering and leaving a protected zone. If the quantities are equal, no fault is present. It operates based on either current balance or voltage balance principles. Current balance differential protection compares currents measured by current transformers on both sides of a zone. An internal fault causes a difference between the currents, triggering operation. Voltage balance differential protection compares voltages induced in secondary windings connected in opposition; an internal fault causes a difference activating the relay. Percentage differential relays include operating and restraining windings. The restraining windings prevent operation for external faults while allowing operation for high resistance internal faults. Differential protection provides high sensitivity and selectivity with relatively high speed operation.

Uploaded by

shashikant yadav
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 10

Power System Protection Part – VII Dr.Prof.

Mohammed Tawfeeq Al-Zuhairi

Differential Protection
(Unit protection)

321
Power System Protection Part – VII Dr.Prof.Mohammed Tawfeeq Al-Zuhairi

Differential Protection
 Differential protection is the best technique in protection. In this type of
protection the electrical quantities entering and leaving the protected zone
or area are compared by current transformers (C.T.s). If the net difference
equal zero, it means no fault exist.
 This system is operating in either of the two following principles:
1. Current balance principle.
2. Voltage balance principle.
 Differential protection is applicable to all parts of the power system:
1. Generator.
2. Transformers.
3. Motors.
4. Buses.
5. Lines and feeders.
6. Reactors and capacitors
There are two basic types of differential protection:
 Current Balance Differential protection
 Voltage Balanced Differential Protection
1. Current Balance Differential protection:
 Operation during internal and external fault conditions
Fig.1 shows the basic current differential protection based on current
balance principle.
- At normal conditions and for external fault at F, CT1 and CT2
circulate currents at their secondary’s Is1 and Is2 (Is1 =Is2) and no
current flow through the relay (ΔI = Is1 - Is2 = 0), hence the relay will
not operate.
- If fault occurs at point F within the protected zone (internal fault) as
shown in Fig.2, and the fault is fed from both sides, then current
through C.T2 will be reversed. Therefore a current ΔI = Is1 + Is2 will
flow in the operating winding of the relay. This will cause the relay to
trip the circuit breaker connected to the faulty system. Hence the relay
trips when
| Is1 +Is2|>|I| |I|=> pick up current of relay
This form of protection is known as Merz-Price protection.

321
Power System Protection Part – VII Dr.Prof.Mohammed Tawfeeq Al-Zuhairi

Fig 1

Consider ideal current transformer performance


 Ip1 = Ip2
 Therefore Is1 = Is2
 Therefore ΔI = 0, magnitude of I = 0
 Current measuring relay does not operate.

325
Power System Protection Part – VII Dr.Prof.Mohammed Tawfeeq Al-Zuhairi

Fig. 2 internal fault with two infeed.

Consider ideal current transformer performance


 If = Ip1+Ip2
 Therefore Is1 ≠ Is2
 Therefore ΔI= Is1+Is2 ≠ 0, magnitude of I > 0
 Current measuring relay operates.

321
Power System Protection Part – VII Dr.Prof.Mohammed Tawfeeq Al-Zuhairi

-Relay may also operate if the fault in feed is from one direction as shown in
fig.3.

Fig 3 internal fault with one infeed.

Consider ideal current transformer performance:


 If = Ip1 as Ip2 = 0 i.e no fault current in feed from one side.
 Is2 = 0
 Therefore ΔI = Is1 ≠0, magnitude of I > 0
 Current measuring relay operates.

2. Voltage Balanced Differential Protection


Instead of current balance, a voltage balance Mertz-Price system, shown
in Fig.4, is used for feeder protection or equipment protection (unit
protection).
 CT1 & CT2 secondary windings are connected in opposition so that there
is no current flow in the relay operating coil (V s1 = Vs2 => relay not
operate).
- During internal fault Vs1 - Vs2 ≠ 0, this will drive current through the
operating coil of the relay and the relay will operate.Fig.5.

321
Power System Protection Part – VII Dr.Prof.Mohammed Tawfeeq Al-Zuhairi

Fig 4

Consider ideal current transformer performance:


 Ip1 = Ip2.
 Vs1 = Vs2 and Is1 = Is2 = 0.
 Therefore magnitude of I = 0
 Current measuring relay does not operate.

Fig 5.

321
Power System Protection Part – VII Dr.Prof.Mohammed Tawfeeq Al-Zuhairi

Consider ideal current transformer performance:


 Vs1 ≠ Vs2.
 Therefore magnitude of I ≠ 0
 Current measuring relay operates.

 The characteristics of differential protection can be summarized as


follows:
Simple Concept:
• Measure current entering and exiting the zone of protection
• If currents are not equal, a fault is present
Provides:
• High sensitivity
• High selectivity
Result:
• Relatively high speed

 Percentage Differential Current Relay


This relay has an operating winding and two restraining winding connected as
shown in Fig.6. The function of the restraining windings is to prevent
undesired relay operation should a current flow in the operating winding due to
CT during external fault.

Figure 6—Basic relay connections (one phase) for fixed percentage restraint
differential relay.
321
Power System Protection Part – VII Dr.Prof.Mohammed Tawfeeq Al-Zuhairi

At Normal conditions:
 The differential current in the operating coil is proportional to Is1-Is2.
Iop = Is1-Is2
 The equivalent current in the restrain windings are proportional to
½ ( Is1+Is2) since the two restrain windings are identical.
Irest = ½ ( Is1+Is2)

 Therefore, the ratio of the differential operational current to the average


restrain current is a fixed “percentage”. In other word, we can define the
bias as the ratio between the numbers of turns of the restrain coil to the
number of turns of the operating coil, i.e.

 k is typically (10 – 40%).

 The operating characteristics of the relay is shown in Fig.7

Fig. 7 Typical operating characteristic of a percentage differential relay.

The electromagnetic forces are proportional to the square of the magneto-


motive force (mmf).
The condition for relay operation is then:

(mmfop )2 ˃ (mmfr )2

(Is1-Is2) No ˃ ½ ( Is1+Is2) Nr
(Is1-Is2) No ˃ ½ (Is1+Is2) k No
311
Power System Protection Part – VII Dr.Prof.Mohammed Tawfeeq Al-Zuhairi

Is1 ˃ (½ ( Is1+Is2)) k + Is2

Is1 – ( k /2) Is1 ˃ ( ½ Is2) k + Is2

Is1 (1 –½ k) ˃ Is2 (1+ ½ k)

These characteristics can be achieved using balanced beam relay shown in


Fig.8.

Fig.8 Balanced beam relay with restrain. (a) Balanced beam type relay (b)
Schematic

313
Power System Protection Part – VII Dr.Prof.Mohammed Tawfeeq Al-Zuhairi

312

You might also like