Oedometer Test: Concept

Oedometer test
From Wikipedia, the free encyclopedia
Jump to navigationJump to search
Two oedometers at the University of Cambridge
An oedometer test is a kind of geotechnical investigation performed in geotechnical

engineering that measures a soil's consolidationproperties. Oedometer tests are performed by
applying different loads to a soil sample and measuring the deformation response. The results from
these tests are used to predict how a soil in the field will deform in response to a change in effective
stress.
Contents
 1Concept
 2History
 3Testing procedures
o 3.1Incremental Loading
 4Results
o 4.1Consolidation Properties
 5See also
 6References
Concept[edit]
Incremental Loading frame developed by Bishop
Oedometer tests are designed to simulate the one-dimensional deformation and drainage conditions
that soils experience in the field. To simulate these conditions, rigid confining rings are used to
prevent lateral displacement of the soil sample. Porous stones are placed on the top and bottom of
the sample to allow drainage in the vertical direction. To better simulate one-dimensional strain, a
diameter-to-height ratio in the sample of 3:1 or more is used. Because the process of consolidation
involves movement of water out of a soil, it is important to prevent drying of the soil.[1]
History[edit]
Consolidation experiments were first carried out in 1910 by Frontard. A thin sample (2in thick by 14in
in diameter) was cut and placed in a metal container with a perforated base. This sample was then
loaded through a piston incrementally, allowing equilibrium to be reached after each increment. To
prevent drying of the clay, the test was done in a room with high humidity.[2]
Karl von Terzaghi started his consolidation research in 1919 at Robert College in Istanbul.[2] Through
these experiments, Terzaghi started to develop his theory of consolidation which was eventually
published in 1923.
The Massachusetts Institute of Technology played a key role in early consolidation research. Both
Terzaghi and Arthur Casagrande spent time at M.I.T. - Terzaghi from 1925 to 1929 and Casagrande
from 1926 to 1932. During that time, the testing methods and apparatuses for consolidation testing
were improved.[3] Research was continued at MIT in the 1940s by Donald Taylor.[4]
Testing procedures[edit]
There are many oedometer tests that are used to measure consolidation properties. The most
common type is the Incremental Loading (IL) test.[1]
Incremental Loading[edit]
The text Soil Mechanics in Engineering Practice describes a general procedure for the Incremental
Loading test. A stiff confining ring with a sharp edge is used to cut a sample of soil directly from a
larger block of soil. Excess soil is carefully carved away, leaving a sample with a diameter-to-height
ratio of 3 or more. Porous stones are placed on the top and bottom of the sample to provide
drainage. A rigid loading cap is then placed on top of the upper porous stone. This assembly is then
placed into a loading frame.
Weights are placed on the frame, imposing a load on the soil. Compression of the sample is
measured over time by a dial indicator. By observing the deflection value over time data, it can be
determined when the sample has reached the end of primary consolidation. Another load is then
immediately placed on the soil and this process is repeated. After a significant total load has been
applied, the load on the sample is decreased incrementally. Using a load increment ratio of 1/2
provides a sufficient number of data points to describe the relationship between void ratio and
effective stress for a soil.[1]
ASTM International has a standard testing procedure for incremental loading: ASTM D2435-
11.[5] Other testing standards such as BS 1377:5 and ISO 17892-5:2017 [6] also are commonly used.
ASTM D3877, ASTM D4546 and AASHTO T216 provide procedures for conducting other similar
tests for determination of the consolidation characteristics of soils. Oedometer test set is required to
perform the test. It is used to determine the consolidation characteristics of soils of low permeability.
Tests are carried out on specimens prepared from undisturbed samples. Ideally, following would be
needed to perform the Oedometer test:
[7]
 1 x Bench
 3 x Oedometers
 3 x Cells, either 50mm or 63.5mm, or 75mm
 3 x Dial gauges, either analogue, or digital
 1 x Weight set
Results[edit]
Oedometer tests provide engineers with very useful data about the soil being tested.
Consolidation Properties[edit]
 Preconsolidation pressure σ'p[8]

 The effective stress that marks the boundary between stiff and soft deformation response of
a soil to loading
 Usually indicative of high loadings in the past from glaciers or eroded layers
 Recompression Index CR = Δe/Δlogσ'v[9]
 How the soil will change volume (settle) under loads less than the preconsolidation pressure
 Can be used to approximate swelling due to unloading
 Compression Index CC = Δe/Δlogσ'v[9]
 How the soil will change volume (settle) under loads greater than the preconsolidation
pressure
 Duration of Primary Consolidation tp[10]
 Secondary Compression Index Cα = Δe/Δlogt[10]
 How the soil will change volume (settle) under a constant loading

Oedometer Test: Concept

Uploaded by

Copyright:

Available Formats

Oedometer Test: Concept

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Oedometer Test: Concept

Uploaded by

Copyright:

Available Formats

Oedometer test

From Wikipedia, the free encyclopedia

Jump to navigationJump to search

Two oedometers at the University of Cambridge

An oedometer test is a kind of geotechnical investigation performed in geotechnical

Incremental Loading frame developed by Bishop

 Preconsolidation pressure σ'p[8]

You might also like