Scribd
Upload
138 views1 page

Applicable ASTM Specifications For Structural Fasteners: Table 3.8 Anchor Rods

This table summarizes ASTM specifications for common structural fasteners including anchor rods, threaded rods, bolts, nuts, and washers. It provides information on the yield stress, tensile stress, diameter range, and other applicable specifications for each type of fastener. Key specifications included are A325, A490, A354, A572, A588, A687, and F1554.

Uploaded by

ivan bolaños
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
138 views1 page

Applicable ASTM Specifications For Structural Fasteners: Table 3.8 Anchor Rods

This table summarizes ASTM specifications for common structural fasteners including anchor rods, threaded rods, bolts, nuts, and washers. It provides information on the yield stress, tensile stress, diameter range, and other applicable specifications for each type of fastener. Key specifications included are A325, A490, A354, A572, A588, A687, and F1554.

Uploaded by

ivan bolaños
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

TA B L E 3 .

8 Applicable ASTM Specifications for Structural Fasteners

Anchor Rods

Threaded Rods
Common Bolts

Direct Tension
High Strength

Threaded &
Indicators
Fy Fu

Washers

Hooked
Headed
Yield Tensile Diameter

Nutted
Bolts

Nuts
ASTM Stress Stressa Range
Designation (ksi) (ksi) (in)

A325 - 105 71 - 1.5


- 120 0.5–1.5
A490 - 150 0.5–1.5
- 105 1.125
F1852
- 120 0.5–1
A194 Gr. 2H - - 0.25–4
A563 - - 0.25–4
F436b - - 0.25–4
F959 - - 0.5–1.5
A36 36 58–80 610
- 100 74 - 7
A193 Gr. B7 - 115 72.5 - 4
- 125 …2.5
Gr. A - 60 0.25–4
A307
Gr. C - 58–80 0.25–4
- 140 2.5–4
A354 Gr. BD
150 0.25–2.5
- 90 1.5–3 c
A449 105 1.125–1.5 c
120 0.25–1 c
Gr. 42 42 60 66
Gr. 50 50 65 64
A572 Gr. 55 55 70 62
Gr. 60 60 75 61.25
Gr. 65 65 80 61.25
42 63 75 - 8
A588 46 67 74 - 5
50 70 64
A687 105 150 max 0.625–3
Gr. 36 36 58–80 0.25–4
F1554 Gr. 55 55 75–95 0.25–4
Gr. 105 105 125–150 0.25–3

= Preferred material specification


= Other applicable material specification, availability should be confirmed before specifying
= Material specification does not apply
- indicates that a value is not specified in the material specification
a
Minimum values unless range or max. is indicated
b
Special washer requirements apply for some steel to steel bolting, check design documents
c
LRFD has limitations on use of ASTM A449 bolts

You might also like