Scribd
Upload
302 views4 pages

TP 2

smi

Uploaded by

Fatima Zahra
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
302 views4 pages

TP 2

smi

Uploaded by

Fatima Zahra
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 4

config switch

PT3000 Boot Loader (PT3000-HBOOT-M) Version 12.1(11r)EA1, RELEASE SOFTWARE (fc1)


Compiled Mon 22-Jul-02 18:57 by miwang
Cisco WS-CSwitch-PT (RC32300) processor (revision C0) with 21039K bytes of memory.
Switch-PT starting...
Base ethernet MAC Address: 000C.855B.E43E
Xmodem file system is available.
Initializing Flash...
flashfs[0]: 1 files, 0 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 64016384
flashfs[0]: Bytes used: 3117390
flashfs[0]: Bytes available: 60898994
flashfs[0]: flashfs fsck took 1 seconds.
...done Initializing Flash.

Boot Sector Filesystem (bs:) installed, fsid: 3


Parameter Block Filesystem (pb:) installed, fsid: 4

Loading "flash:/pt3000-i6q4l2-mz.121-22.EA4.bin"...
######################### [OK]
Restricted Rights Legend

Use, duplication, or disclosure by the Government is


subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.


170 West Tasman Drive
San Jose, California 95134-1706

Cisco Internetwork Operating System Software


IOS (tm) PT3000 Software (PT3000-I6Q4L2-M), Version 12.1(22)EA4, RELEASE SOFTWARE
(fc1)
Copyright (c) 1986-2006 by cisco Systems, Inc.
Compiled Fri 12-May-06 17:19 by pt_team

Cisco WS-CSwitch-PT (RC32300) processor (revision C0) with 21039K bytes of memory.
Processor board ID FHK0610Z0WC
Running Standard Image
6 FastEthernet/IEEE 802.3 interface(s)

63488K bytes of flash-simulated non-volatile configuration memory.


Base ethernet MAC Address: 000C.855B.E43E
Motherboard assembly number: 73-5781-09
Power supply part number: 34-0965-01
Motherboard serial number: FOC061004SZ
Power supply serial number: DAB0609127D
Model revision number: C0
Motherboard revision number: A0
Model number: WS-CSwitch-PT
System serial number: FHK0610Z0WC

Cisco Internetwork Operating System Software


IOS (tm) PT3000 Software (PT3000-I6Q4L2-M), Version 12.1(22)EA4, RELEASE SOFTWARE
(fc1)
Copyright (c) 1986-2006 by cisco Systems, Inc.
Compiled Fri 12-May-06 17:19 by pt_team

Press RETURN to get started!

%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to


up

%LINK-5-CHANGED: Interface FastEthernet1/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/1, changed state to


up

Switch>en

Switch#config t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#vlan 500
Switch(config-vlan)#name etudiants
Switch(config-vlan)#exit
Switch(config)#vlan 700
Switch(config-vlan)#name enseignants
Switch(config-vlan)#exit
Switch(config)#int fa 0/1
Switch(config-if)#switchport access vlan 500
Switch(config-if)#exit
Switch(config)#int fa 1/1
Switch(config-if)#switchport access vlan 700
Switch(config-if)#exit
Switch(config)#int fa 2/1
Switch(config-if)#switchport mode trunk
Switch(config-if)#
Switch(config-if)#exit.

%LINK-5-CHANGED: Interface FastEthernet2/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet2/1, changed state to


up

-----------------------------------------------------------------------------------
----------------------------------------------------------------

config routeur

System Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1)


Copyright (c) 2000 by cisco Systems, Inc.
Cisco 2620 (MPC860) processor (revision 0x200) with 253952K/8192K bytes of memory
Readonly ROMMON initialized

Self decompressing the image :


######################### [OK]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is


subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.


170 West Tasman Drive
San Jose, California 95134-1706

Cisco Internetwork Operating System Software


IOS (tm) C2600 Software (C2600-I-M), Version 12.2(28), RELEASE SOFTWARE (fc5)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Wed 27-Apr-04 19:01 by miwang

Cisco 2620 (MPC860) processor (revision 0x200) with 253952K/8192K bytes of memory
.
Processor board ID JAD05190MTZ (4292891495)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
32K bytes of non-volatile configuration memory.
63488K bytes of ATA CompactFlash (Read/Write)

Press RETURN to get started!

Router>en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa 0/0.500
Router(config-subif)#encapsulation dot1q 500
Router(config-subif)#ip address 172.16.0.1 255.255.0.0
Router(config-subif)#no sh
Router(config-subif)#exit
Router(config)#int fa 0/0.700
Router(config-subif)#encapsulation dot1q 700
Router(config-subif)#ip address 10.0.0.1 255.0.0.0
Router(config-subif)#no sh
Router(config-subif)#exit

Router(config)#int fa0/0
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to


up

%LINK-5-CHANGED: Interface FastEthernet0/0.500, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.500, changed state


to up

%LINK-5-CHANGED: Interface FastEthernet0/0.700, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.700, changed state


to up

Router(config-if)#exit
Router(config)#do show ip interface br
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 unassigned YES unset up up
FastEthernet0/0.500 172.16.0.1 YES manual up up
FastEthernet0/0.700 10.0.0.1 YES manual up up
Router(config)#

You might also like