Catalogo Valvulas Hdcas Sun PDF

Over 40 New Products in this Catalogue
Relief Cartridge Valves Page 39: The PV*A-8 is a normally open modulating element
with a T-8A cavity in the end and an external drain. This
Page 9: The RP*S is a seated style pilot operated relief valve.
would enable any Sun pilot valve, such as the RBAP
This provides reduced leakage, faster response and a
proportional valve, to be fitted into the end to make a
reduced pressure overshoot to give improved pressure
proportional pressure reducing/relieving valve with
control.
external drain.
Page 10: The RPGT is a "soft start" relief valve available in
series 2 only providing a pressure ramping over 300
milliseconds when it opens to provide excellent pressure Page 40 and 41: The PRD* is an electro-proportional, direct
protection and reduce shock. acting, pressure reducing/relieving valve available in
series 1 only. There are two versions available, one with
Page 13: The RBAP is an electro-proportional, direct acting
low leakage and the other with higher leakage and
pilot relief valve that fits into the Sun T-8A cavity. It can
improved response.
be used as a pilot valve on it's own or together with many
types of main stage pressure control valves that have the
T-8A cavity in the end of the cartridge. Flow Control Cartridge Valves
Page 14: The RP*C-8 is a normally closed spool type
Page 73: The FPCC is an electro-proportional, normally
modulating valve, with a T-8A cavity in the end. This
closed throttle valve available in series 1 only. It provides
would enable any of the Sun pilot valves, such as the
some pressure compensation but needs a separate
RBAP proportional valve, to be fitted into the end to
compensator for more accurate control.
make a high capacity proportional relief valve.
Page 15: The RP*S-8 is a seated style normally closed
Page 74: The FPCH is an electro-proportional, normally open
modulating valve, with a T-8A cavity in the end. This
throttle valve available in series 1 only. It provides some
would enable any of the Sun pilot valves, such as the
pressure compensation but needs a separate compensator
RBAP proportional valve, to be fitted into the end to
for more accurate control.
make a proportional relief valve with low leakage on the
main stage.
Page 18: The RV*S is a ventable, seated style, pilot operated Priority Flow Control Cartridge Valves
relief valve. This provides reduced leakage, faster
Page 78: The FV*A-8 is a ventable, fixed orifice, priority flow
response and a reduced pressure overshoot to give
control valve with a T-8A cavity in the end of the
improved pressure control.
cartridge. This enables a Sun pilot solenoid, pneumatic or
Page 20: The RV*D-8 is a normally closed, balanced piston, manual valve to be fitted into the cartridge to select the
modulating element with a T-8A cavity in the end. The priority flow condition or bypass all flow to tank.
cartridge is ventable and also has an external drain
connection. This would enable any Sun pilot valve, such
as the RBAP proportional valve, to be fitted into the end Logic Elements
to make a ventable proportional relief with separate drain
Page 89: The LO**-8 is a poppet type, spring biased closed,
port.
pilot-to-close unbalanced logic valve with a T-8A cavity
Sequence Cartridge Valves in the end of the cartridge. This enables a Sun pilot
solenoid, pneumatic or manual valve to be fitted into the
Page 23: The RSDC-8 is a normally closed, balanced piston,
cartridge to select the valve in the open or closed
modulating element with a T-8A cavity in the end and
condition.
external drain. This would enable any Sun pilot valve
such as the RBAP proportional valve to be fitted into the
end to make a relief valve with separate pilot drain.
Page 95: The DO*R-8 is a poppet type, pilot-to-close,
normally open balanced logic valve with a T-8A cavity in
Reducing/Relieving Cartridge Valves the end of the cartridge. This enables a Sun pilot solenoid,
Page 37: The PB*B-8 is a normally open modulating element pneumatic or manual valve to be fitted into the cartridge
with a T-8A cavity in the end. This would enable any Sun to select the valve in the open or closed condition.
pilot valve such as the RBAP proportional valve to be
fitted to make a proportional pressure reducing valve. Page 100: The DK*R-8 is a poppet type, pilot-to-open,
Page 38: The PP*B-8 is a normally open modulating element normally closed balanced logic valve with a T-8A cavity
with a T-8A cavity in the end. This would enable any Sun in the end of the cartridge. This enables a Sun pilot
pilot such as the RBAP proportional valve to be fitted into solenoid, pneumatic or manual valve to be fitted into the
the end to make a proportional pressure reducing/ cartridge to select the valve in the open or closed
relieving valve. condition.
US Shortcut Catalogue #999-901-243 1

Over 40 New Products in this Catalogue
Directional Cartridge Valves pneumatic or manual valve to be fitted into the cartridge
to select the valve in the open or closed condition.
Page 108: The DF*A-8 two-position, two-way normally
Page 105: The DRBO is direct acting, externally drained,
closed port 1 to 2, directional valve with a T-8A cavity in
normally closed, three-way directional valve in series 1
the end of the cartridge. This enables a Sun pilot solenoid,
only. It is available with an adjustment on the pressure at
pneumatic or manual valve to be fitted into the cartridge
which the valve will switch.
to select the valve in the open or closed condition.
Page 105: The DRBP is direct acting, externally drained, Page 109: The DF*B-8 two-position, two-way normally
normally open, three-way directional valve in series 1 closed port 2 to 1, directional valve with a T-8A cavity in
only. The valve is available with an adjustment on the the end of the cartridge. This enables a Sun pilot solenoid,
pressure at which the valve will switch. pneumatic or manual valve to be fitted into the cartridge
Page 105: The DRBR is a direct acting, internally drained, to select the valve in the open or closed condition.
externally piloted, three-way directional valve in series 1
only. The valve is available with an adjustment on the Pilot Control Cartridge Valves
pressure at which the valve will switch. Page 125: The DAAM is a manually operated, two-position,
Page 106: The DV*A-8 is a direct acting, normally open, two- two-way pilot valve. This valve could be fitted into any
way directional valve with a T-8A cavity in the end. This cartridge with a T-8A cavity in the end to provide manual
enables a Sun pilot solenoid, pneumatic or manual valve switching. Available with momentary, detented, or dual
to be fitted into the cartridge to select the valve in the operator.
open or closed condition. Page 129: The DBAM is a manually operated, two-position,
three-way valve.
Page 106: The DV*B-8 is a direct acting, normally closed,
two-way directional valve with a T-8A cavity in the end.
Circuit Savers
This enables a Sun pilot solenoid, pneumatic or manual
valve to be fitted into the cartridge to select the valve in Page 146: The COFO is a 120:1 ratio, pilot to close check
the open or closed condition. valve in series 2 only. This valve is specifically designed
for accumulator unloading and dump circuits when the
Page 106: The DV*C-8 is a direct acting, three-way directional pump is not operating.
valve with Port 1 blocked and a T-8A cavity in the end. Page 152: The DS*X is a two-position, three-way, vent-to-
This enables a Sun pilot solenoid, pneumatic or manual shift, normally closed diverter valve. This valve could be
valve to be fitted into the cartridge to select the valve in used in parallel with flow divider valves to enable the
the open or closed condition. function to be bypassed in traction drive circuits.
Page 106: The DV*D-8 is a direct acting, three-way directional Page 153: The DS*Y is a two-position, three-way, vent-to-
valve with Port 1 open and a T-8A cavity in the end. This shift diverter valve. This valve works as a simple flow
enables a Sun pilot solenoid, pneumatic or manual valve to diverter valve.
be fitted into the cartridge to select the valve in the open or Page 154: The LHDT is a bi-directional, normally open
closed condition. modulating valve in series 1 only. This valve can be used
with an external orifice to provide pressure compensated
Page 107: The DV*M-8 is a vent-to-operate two-position two-
way, normally open directional valve with a T-8A cavity in flow control in both directions.
the end and external drain. This enables a Sun pilot
solenoid, pneumatic or manual valve to be fitted into the
Hybrid Relief Cartridge Valves
cartridge to select the valve in the open or closed condition. Page 156: The HRDA is a dual function cartridge providing
both a direct acting relief valve and check valve. The
Page 107: The DV*N-8 is a vent-to-operate two-position two- relief function is before the check valve.
way, normally closed directional valve with a T-8A cavity Page 157: The HRDB is a dual function cartridge providing
in the end and external drain. This enables a Sun pilot both a direct acting relief valve and check valve. The
solenoid, pneumatic or manual valve to be fitted into the relief function is after the check valve.
cartridge to select the valve in the open or closed condition.
Page 158: The HVCA is a dual function cartridge providing
Page 107: The DV*O-8 is a vent-to-operate two-position both a ventable pilot operated relief and check valve. The
three-way directional valve with a T-8A cavity in the end ventable relief function is before the check valve.
and external drain. This enables a Sun pilot solenoid, Page 159: The HVCA-8 is a dual function cartridge providing
pneumatic or manual valve to be fitted into the cartridge both a normally closed modulating function and a check
to select the valve in the open or closed condition. valve and a T-8A cavity in the end of the cartridge. This
Page 107: The DV*P-8 is a vent-to-operate two-position three- would enable a Sun pilot valve such as a pilot
way directional valve with a T-8A cavity in the end and proportional valve to provide a proportional pressure
external drain. This enables a Sun pilot solenoid, control and check function in one cartridge.
2 US Shortcut Catalogue #999-901-243

Contents
Relief Cartridge Valves . . . . . . . . . . . . . . . . . . . . . . . . 5 Solenoid Operated Cartridge Valves . . . . . . . . . . . 113

Sequence Cartridge Valves . . . . . . . . . . . . . . . . . . . . 21 Pilot Control Cartridge Valves . . . . . . . . . . . . . . . . . 121
Reducing and Reducing/Relieving . . . . . . . . . . . . . 29 Shuttle Cartridge Valves . . . . . . . . . . . . . . . . . . . . . . . 135
Cartridge Valves
Circuit Savers. . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Pilot Operated Check Cartridge Valves . . . . . . . . . 43
Hybrid Relief Cartridge Valves . . . . . . . . . . . . . . . . 155
Counterbalance Cartridge Valves . . . . . . . . . . . . . . 47
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Check Cartridge Valves . . . . . . . . . . . . . . . . . . . . . . . . 59
Cartridge Control Options. . . . . . . . . . . . . . . . . . . . . . . . . . 162
Flow Control Cartridge Valves . . . . . . . . . . . . . . . . . 65 Cartridge Control Kits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Cavity Plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
Priority Flow Control Cartridge Valves . . . . . . . . 75 Solenoid Electrical Connector Options. . . . . . . . . . . . . . . . 167
Flow Divider/Combiner Cartridge Valves . . . . . . 81 Orifice Pressure Drop Data . . . . . . . . . . . . . . . . . . . . . . . . . 168
Model Code Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
Logic Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Directional Cartridge Valves . . . . . . . . . . . . . . . . . . . 101
Model Codes printed in Red are Preferred Versions of products

shown in this catalogue and most readily available.
SUN RECOMMENDED QUANTITY DISCOUNTS FOR STANDARD VALVES

One line item One order One shipment F.O.B. Sarasota, FL. USA
Prices shown for SUN Cavity form tools are net and not subject to discounts.
Prices for Custom Products and Modifications of Standard Valves are by quotation only.
Quantity: 1-2 3-9 10-29 30-99 100-299 300-999

Discount: List 7% 15% 25% 35% On Request
Consult your SUN distributor for terms and conditions covering blanket orders or orders for scheduled repetitive shipments.
Sun Hydraulics Corporation reserves the right to change existing prices and discounts at any time without notice to its customers.
Selling prices are governed by the price list in effect at the time of acceptance of a purchase order.

Specifications, descriptions and illustrative material contained herein were accurate as known at the
time this publication was approved for printing.
Sun Hydraulics reserves the right to discontinue models at any time, or change prices, specifications
or designs without notice or incurring obligation.
All rights reserved. This book, or any part thereof, may not be reproduced or transmitted in any form
or by any means, electronic or mechanical, including photocopying, recording,
or information storage and retrieval systems, for any purpose
without the express written permission of Sun Hydraulics Corporation,
1500 West University Parkway, Sarasota, Florida, 34243, USA.
Copyright © 2004 Sun Hydraulics Corporation

Sarasota, FL 34243 USA
Printed in the United States of America

Relief Cartridge Valves
Cartridge Type Page
2 1
Pilot Operated, Balanced Piston 6
2 1 Direct Acting 7
2 1 Direct Acting, Pilot Stage 8
2 1
Pilot Operated, Balanced Poppet 9
2 1
Pilot Operated, Balanced Poppet, Soft Start 10
2 1
Pilot Operated, Kick-down 11
Air Pilot
Pilot Operated, Balanced Piston, Air Controlled 12

2 1
2 1
Electro-proportional Pilot 13
T-8A
Cav
Balanced Piston, Modulating Element with
2 1 Integral Pilot Control Cavity 14
T-8A
Cav
Balanced Poppet, Modulating Element with

2 1 15
Integral Pilot Control Cavity
3
2 1
Ventable, Pilot Operated, Balanced Piston 16
Modulating Element with Relief Function 17

1
2
3
2 1
Ventable, Pilot Operated, Balanced Poppet 18
4 3 Ventable, Pilot Operated, Balanced Piston with

19
2 1 External Drain
3
4 T-8A
Ventable, Balanced Piston, Modulating Element
Cav
with External Drain and Integral Pilot Control 20

2 1
Element

Relief Valves
OPERATED,BALANCED
PILOT OPERATED BALANCEDPISTON,
PISTON
Full Adjustment 5 Turns
+ -
2 1
c
b
Locating
Shoulder
Cartridge Dimensions
Typical c Installation
Capacity Cartridge Cavity a b Torque
Model Code L C K (lb. ft.)
a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
RPCC RPEC RPGC RPIC RPKC
Typical Pressure Rise
5000 5000 5000 5000
5000 5000
5000
5000 5000 5000
4000 4000 4000 4000
psi
4000 4000 4000 4000 4000

PP==psi
4000
psi
psi
psi
psi
PP== psi
PP== psi
PP== psi
PP== psi
3000 3000 3000 3000

3000 3000
3000
3000 3000 3000
2000 2000 2000 2000
2000 2000
2000
2000 2000 2000
1000
1000 1000 1000 1000
1000 1000
1000
1000 1000
0 5 10 15 20 25 0 10 20 30 40 50 0 20 40 60 80 100
100 0
0 40
40 80
80 120
120 160 200
160 200 0
0 80
80 160
160 240
240 320 400
320 400
0 5 10 15 20 25 0 10 20 30 40 50 0 20 40 60 80
Flow =
= GPM
GPM Flow =
Flow = GPM
GPM Flow =
Flow = GPM
GPM Flow =
Flow = GPM
GPM Flow =
Flow = GPM
GPM
Flow
■
■ Maximum operating pressure = 5000 psi
■
■ Will accept maximum pressure at Port 2.
■
■ Back pressure on the tank port (port 2) is directly additive at a 1:1 ratio to the valve setting.
■
■ Factory pressure settings established at 4 GPM
■
■ Typical response time 10 ms.
■
■ Maximum leakage = RPCC, RPEC: 2 in 33/min./1000 psi, RPGC: 3 in33/min./1000 psi, RPIC: 4
in33/min./1000 psi, RPKC: 5 in33/min./1000 psi.
■
■ RPCC minimum setting for all spring ranges is 75 psi
OPTION ORDERING INFORMATION Model Codes printed in Red are Preferred Versions and most readily available
RP ✱ C – ✱ ✱ ✱
Nominal
Capacity Control** Adjustment Range Seal
C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
W 150 - 4500 psi +$ 0.00
Adjustment Range Options:

A, B, C, and W are standard set at 1000 psi.
N Option is standard set at 400 psi.
Q Option is standard set at 200 psi.
** See page 162 for information * Minimum setting 75 psi on all ranges.
on Control Options Customer may specify pressure setting. +$ 1.10
Visit www.sunhydraulics.com for detailed and complete technical information on our full line of products.
6 US Shortcut
US Shortcut Catalogue
Catalogue #999-901-243
#999-901-243
Relief Valves
Relief Valves
DIRECT ACTING
PILOT OPERATED, BALANCED PISTON
Full Adjustment
+ -5 Turns
+ -
2 1
2 1
b cc
b
Locating
Shoulder Cartridge Dimensions
Locating Cartridge Dimensionsc
Shoulder Typical Installation
Capacity TypicalCartridge Cavity a b c Torque
Installation
Capacity Model Code Cavity
Cartridge a b L C (lb.Torque
ft.)
12 GPM RDBA – LAN T - 162A 1.22 3/4” 2.11 2.17 25/30
aa 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
25 GPM RDDA – LAN T - 10A 1.56 7/8” 2.38 2.44 30/35
2 2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
Outlet 50 GPM RDFA – LAN T - 3A 1.88 1 1/8” 2.50 2.56 45/50
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
100 GPM RDHA – LAN T - 16A 2.44 1 1/4” 3.25 3.31 150/160
Inlet 1 100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1 200 GPM RDJA – LAN T - 18A 3.13 1 5/8” 3.94 4.07 350/375
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
Performance Curves
RDBA RDDA RDFA RDHA RDJA
5000
Typical Pressure Rise 5000 5000
5000 5000
4000
5000 5000
4000 5000
4000 5000
4000 5000
4000
= psi
= psi
= psi
= psi
psi
3000 4000 4000 4000

3000 4000
PP==psi
4000 3000 3000 3000

P =Ppsi
P =Ppsi
P =Ppsi
P =Ppsi
3000
2000 3000
2000 3000 3000
2000 3000
2000
2000
2000
1000 2000 2000 2000
1000 2000
1000
1000 1000
1000 1000 1000 1000 1000
0 2 4 6 8 10 12 0 5 10 15 20 25 0 10 20 30 40 50 0 20 30 40 50 60 0 40 80 120 160 200
0 5 Flow
10 = GPM
15 20 25 0 10 Flow
20 = 30
GPM 40 50 0 20 Flow
40 = GPM
60 80 100 0 40 Flow
80 = 120
GPM160 200 0 80 Flow
160 = 240
GPM320 400
Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM
■
■ Maximum operating
Maximum operating pressure
pressure == 5000
5000 psipsi
Will accept maximum pressure at Port 2. 1.
Cannot be adjusted with pressure at Port
■
■
■
■ Will accept
Back pressure maximum
on the tankpressure at Port
port (port 2. directly additive at a 1:1 ratio to the valve setting.
2) is
■
■ Back pressure
Factory pressure onsettings
the tankestablished
port (port 2)at 4isGPM
directly additive at a 1:1 ratio to the valve setting.
■
■ Factory pressure settings
Typical response time 10 ms. established at 4 GPM
■
■ Typical response
Maximum leakagetime 2 ms. RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
= RPCC,
■ in 3/min./1000
Maximum psi, RPKC:
leakage 5 in3/min./1000
= 10 drops/min. psi.
at reseat.
■■ RPCC
Reseatminimum
exceeds 90%setting for all spring
of cracking ranges is 75 psi
pressure.
RD ✱
RP ✱CA –– ✱
✱ ✱
✱✱✱
Nominal
Nominal
B 12 GPM $ 31.90 L Standard Screw +$ 0.00 A 500 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
D 25 GPM $ 34.20 C Tamper Resistant +$ 4.10 B 300 - 1500 psi +$ 0.00 V Viton +$ 2.00
F 50 GPM $ 51.80 C 1000 - 6000 psi
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
H 100 GPM $ 94.30 D 200 - 800 psi
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
J 200 GPM $187.00 E 100 - 400 psi
W
S 150 - 4500
50-200 psipsi +$ 0.00
W 1000 - 4500 psi
NAdjustment Range Options:
Option is standard set at 400 psi.
QA,Option
B, C, and W are standard
is standard setpsi.
set at 200 at 1000 psi.
** See page 162 for information *DMinimum
Option issetting
standard
75 set
psi at
on400 psi.
all ranges.
on Control Options E Option ismay
Customer standard
specifysetpressure
at 200 psi.
setting. +$ 1.10
U.S. Patent #4,742,846 ** See page 162 for information S Option is standard set at 100 psi.
European Patent Pending on Control Options Customer may specify pressure setting.
US Shortcut Catalogue #999-901-243
Visit www.sunhydraulics.com for detailed and complete
7 technical information on our full line of products.
Relief Valves
Relief Valves
+ -
DIRECT ACTING, PILOT STAGE
Full Adjustment 5 Turns 2 1
+ - c
b
2 1
Locating
Shoulder
c Cartridge Dimensions
b Capacity Cartridge Cavity a b
L C K
Torque
Model Code (lb. ft.)
a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
Locating
2 Shoulder Cartridge Dimensions
25 GPM RPEC Typical
– LAN T - 10A 1.56 7/8” 2.00 2.06
c
2.25 30/35
Installation
Outlet
50Capacity
GPM RPGCCartridge
– LAN Cavity
T - 3A 1.88 a b
1 1/8” 2.12
L 2.18
C K2.38
Torque
45/50
a 100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1 60 in.3/min. RBAC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
2 200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
3
120 in. /min. RBAA – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
Outlet
Performance Curves
RPCC Inlet 1 RPEC RPGC RPIC RPKC
Performance
5000 Curves 5000 5000 5000 5000
4000 4000 4000 4000
P = psi
4000
RBAC RBAA
P = psi
P = psi
P = psi
P = psi
3000 3000 3000 3000 3000

2000 2000 2000 2000 2000
1000 1000
Typical
1000
Pressure Rise 1000 1000
5000 5000
0 5 10 15 20 25 0 10 20 30 40 50 0 20 40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
Flow = GPM Flow = GPM 4000 Flow = GPM
4000 Flow = GPM Flow = GPM
P = psi
3000 3000
2000 pressure = 5000 psi 2000
P
1000 1000
0 20 40 60 80 100 0 40 80 120 160 200
■ Back pressure on the tank Flow =port (port 2) is directly additive
in. //min.
3 at a 1:1 ratio to the valve setting.
//min.
3
■
■ Factory
Maximum pressure settings
operating established
pressure = 5000at psi4 GPM
■
■ Typical
Typical response
response time
time 10 ms.
2 ms.
■
■ Maximum
Maximum leakage
leakage = RPCC,
less than 5RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
drops/min.
■ Back pressure on the tank port (port 2) is directly additive at a 1:1 ratio to the valve setting
RP ✱
RB AC✱ – ✱ ✱✱
Nominal
C 12 in.3/min. $ 31.90
60 GPM* 37.30 L Standard Screw +$ 0.00 A 100
25 - -3000
3000psi
psi +$ 0.00 N Buna-N +$ 0.00
E
A 25
120GPM $ 36.20
in.3/min.$ 52.20 C Tamper Resistant +$ 4.10 B 50
25 - 1500 psi +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150
25 - -6000
6000psi
psi +$ 2.00
I 100 GPM $ 97.30 N
D 60
25 - 800 psi +$ 1.00
K 200 GPM $187.00 Q
E 60
25 - 400 psi +$ 1.00
W 150
W 25 - -4500
4500psi
psi +$ 0.00

D Option is standard set at 400 psi.
** See page 162 for information E Option is standard set at 200 psi.
Visit www.sunhydraulics.com for detailed
on Control Options and complete technical information
Customer may specifyon our full
pressure line of products.
setting.
Relief Valves
PILOT OPERATED, BALANCED POPPET
2 1
c
b
Locating
Shoulder
a Capacity Cartridge Cavity a b Torque
Model Code L C (lb. ft.)
2
Outlet 50 GPM RPGS – LAN T - 3A 1.88 1 1/8” 2.12 2.18 45/50
100 GPM RPIS – LAN T - 16A 2.44 1 1/4” 2.44 2.47 150/160
Inlet 1
Performance Curves
RPGS RPIS
4000 4000
3000 3000
P = psi
P = psi
2000 2000
1000 1000
0 25 50 75 100 0 50 100 150 200

Flow = GPM Flow = GPM
■ Maximum leakage 10 drops/min. at reseat
■ Reseat exceeds 90% of cracking pressure.
OPTION ORDERING INFORMATION

RP ✱ S – ✱ ✱ ✱
Nominal Control** Adjustment Range Seal
Capacity
G 50 GPM $ 61.80 C Tamper Resistant +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 1.50
Factory Set
I 100 GPM $112.30 B 50 - 1500 psi +$ 0.00 V Viton
K Handknob
C 150 - 6000 psi
L Standard Screw
Adjustment N 60 - 800 psi
Q 60 - 400 psi
W 100 - 4500 psi

** See page 162 for information Q Option is standard set at 200 psi.
on Control Options Customer may specify pressure setting.
Relief Valves
PILOT OPERATED, BALANCED POPPET, SOFT START
2 1
c
b
Locating
Shoulder Typical c Installation
a 50 GPM RPGT - LAN T - 3A 1.88 1 1/8” 3.38 3.47 45/50
2
Outlet
Inlet 1
Performance Curves
RPGT
Typical Pressure Rise Typical Ramp Time
6000 5000
5000 4000
P = psi
P = psi
Setting
4000
3000 3250 psi e.g.
3000
2000 Threshold
2000
at 3250 psi
1000 1000
Setting
0 10 20 30 40 50 0 200 400 600 800 1000

Flow = GPM Time/ms.

■ Shifting time from minimum to maximum setting 250 ms.
■ Control pilot flow = 10 to 25 in3/min.

RP G T – ✱ ✱ ✱
Nominal
G 50 GPM $ 99.00 C Tamper Resistant +$ 4.10 A 2000 - 3000 psi +$ 0.00 N Buna-N
Factory Set
C 4500 - 6000 psi +$ 2.00 V Viton
L Standard Screw
Adjustment W 3000 - 4500 psi

Patents: A is standard set at 2000 psi.
U.S. #6,039,070; C is standard set at 4500 psi.
Germany EP 1 001 197; ** See page 162 for information W is standard set at 3000 psi.
Japan #3,119,230 on Control Options Customer may specify pressure setting.
Relief Valves
PILOT OPERATED, KICK-DOWN
+ -
2 1
c
b
Locating
Shoulder
a 25 GPM RQEB – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
2
Outlet
50 GPM RQGB – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
100 GPM RQIB – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
200 GPM RQKB – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Inlet 1
Performance Curves
RQEB RQGB RQIB RQKB
Unloaded Pressure Drop
300 300 300 300
250 250 250 250
P = psi
P = psi
200 200 200

C&W C&W
150 150 150 150
A A
100 C&W 100 C&W 100 100
A B, N, Q B, N, Q
A 50
50 B, N, Q 50 B, N, Q 50
0 5 10 15 20 25 0 10 20 30 40 50 0 20 40 60 80 100 0 40 80 120 160 200

Flow = GPM Flow = GPM Flow = GPM Flow = GPM

■ Flow through cartridge must cease to reset valve.
■ Factory pressure settings established at kick down point.
■ Maximum leakage = RQEB: 2 in3/min./1000 psi; RQGB: 3 in3/min./1000 psi, RQIB: 4
in3/min./1000 psi, RQKB: 5 in3/min./1000 psi

RQ ✱ B – ✱ ✱ ✱
Nominal
Control** Adjustment Range Seal
Capacity
E 25 GPM $ 45.80 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N
G 50 GPM $ 63.00 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton
I 100 GPM $109.90 K Handknob +$ 5.00 C 150 - 6000 psi
K 200 GPM $208.00 N 60 - 800 psi
Q 60 - 400 psi
W 150 - 4500 psi

** See page 162 for information Q Option is standard set at 200 psi.
Relief Valves
PILOT OPERATED, BALANCED PISTON, AIR CONTROLLED
Air Pilot Port Air Pilot
c 2 1
b
Locating
Shoulder
a Model Code A B (lb. ft.)
2 50 GPM RPGD – ABN T - 3A 1.88 1 1/8” 1.31 - 45/50
Outlet 100 GPM RPID – BBN T - 16A 2.44 1 1/4” - 1.62 150/160
200 GPM RPKD – BBN T - 18A 3.13 1 5/8” - 2.00 350/375
Inlet 1
Performance Curves
RPGD RPID RPKD
2500 2500 2500
2000 2000 2000
P = psi
P = psi
P = psi
1500 1500 1500

1000 1000 1000
500 500 500
0 25 50 75 100 0 50 100 150 200 0 100 200 300 400

Flow = GPM Flow = GPM Flow = GPM

■ Maximum air pressure should not exceed 150 psi.
■ Pilot ratio, air to hydraulic = 1:20
■ Maximum leakage = RPGD: 3 in3/min./1000, RPID: 4 in3/min./1000 psi, RPKD: 5 in3/min./1000 psi.

RP ✱ D – ✱ ✱ ✱
Nominal
Control Adjustment Range Seal
Capacity
G 50 GPM $121.60 Available for RPGD only B 50 - 1500 psi +$ 0.00 N Buna-N
I 100 GPM $167.20 A 1/4" NPTF +$ 0.00 V Viton

Pilot Port at
K 200 GPM $314.00 end of Cartridge*
Available for RPID, RPKD only

B SAE-4 +$ 0.00
Pilot Port at
end of Cartridge*
* Maximum air pilot pressure
should not exceed 150 psi.
Relief Valves
ELECTRO-PROPORTIONAL PILOT
Relief Valves
2 1
+ - d
2 1
Typical Installation
b Capacity Cartridge Cavity a b c d Torque
c Model Code (lb. ft.)
b Locating
Locating .25 GPM RBAP – MAN T - 8A .75 7/8 .59 2.76 25/30
Shoulder Shoulder
2 Cartridge Dimensions
a
Outlet Typical c Installation
Inlet 1 Model Code L C K (lb. ft.)
a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
Performance Curves 50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
100 GPM RPIC – LAN RBAP
T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
200 GPM Constant
RPKC Command
– LAN T - 18APressure vs. Command
3.13 1 5/8” 2.81 2.94 3.06 350/375
Varying Flow Flow 0.1 GPM
Performance Curves 4000 4000
RPCC RPEC RPGC 3000

RPIC RPKC
P = psi
3000
P = psi
2000 2000
1000 Typical Pressure

1000 Rise
5000 5000 5000 5000 5000

0 25 50 75 100 120 0 20 40 60 80 100
4000
inch3/min. 4000 Command (%)
4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
3000 3000 3000 3000 3000

2000 2000 2000 2000 2000
1000 ■ Maximum
1000 operating pressure1000= 5000 psi 1000 1000
0 5 10 15 20 ■ 25 Maximum0 10 leakage
20 30 =401.550 in3/min0 at20reseat
40 60 80 100 0 40 80 120
Flow = GPM
160 200 0 80 160 240 320 400
■ Back pressure on the tank port (port 2) is directly additive at a 1:1 ratio to valve setting
■ Hysteresis with dither <4%
■ Hysteresis with DC input <8%
■ Linearity with dither <2%
■ For optimum performance, an amplifier with current sensing and adjustable dither should be used.
■ Maximum
Dither shouldleakage = RPCC,between
be adjustable RPEC: 2100 in 3-/min./1000 3
250 Hz. psi, RPGC: 3 in /min./1000 psi, RPIC: 4
3 3
in /min./1000 psi, RPKC: 5 in /min./1000 psi.
RP A
RB ✱PC – ✱ ✱✱
Nominal
Nominal
Capacity Control**
Control** Adjustment Range
Adjustment Range Seal
Seal
Capacity
A .25 GPM $105.00 M Manual Override +$ 0.00 A 300 - 3000 psi +$ 0.00 N Buna-N $
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10
(Standard) B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 K Handknob +$ 5.00 B
C 150
150 -- 1500
6000 psi
psi +$
+$ 0.00
2.00 V Viton
NOTE: Coil must be
I 100 GPM $ 97.30 ordered separately. Use N 500
W 60 - -800 psipsi
5000 +$ 1.00
12V DC or 24V DC
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
(Series 770-***) coils
only. See page 167. W 150 - 4500 psi +$ 0.00

** See pagefor
Visit www.sunhydraulics.com 162 for information
detailed * Minimum
and complete technical setting 75 psi
information onon allfull
our ranges.
line of products.
Relief Valves
BALANCED PISTON, MODULATING ELEMENT WITH INTEGRAL
PILOT CONTROL CAVITY
Relief Valves
The -8 control option allows a pilot control valve to be incorporated directly
into the end of the modulating element via the T-8A cavity. These pilot control
T-8A
Cav
cartridges are sold separately and include electro-proportional, solenoid, air
Full Adjustment 5 Turns pilot, and hydraulic pilot operation. See Pilot Control Cartridges on page 121.
b + - 2 1
c
Locating
Shoulder 2 1
c
b a Cartridge Dimensions
2 Typical Installation
Outlet Locating
Shoulder Capacity Cartridge Cavity a b c Torque
Model Code Cartridge Dimensions (lb. ft.)
25 GPM RPEC – 8WN
Typical T - 10A 1.56 7/8 .75 c 30/35Installation
Inlet 1 50 GPM ModelRPGC
Code – 8WN T - 3A 1.88 1 1/8”L .69 C K 45/50 (lb. ft.)
a 12 100
GPM GPM RPCCRPIC
– LAN– 8WN T - 162AT - 16A1.22 2.443/4” 2.11
1 1/4” .972.17 2.31150/160 25/30
2 25 200
GPM GPM RPECRPKC
– LAN– 8WN
T - 10AT - 18A1.56 3.137/8” 2.00
1 5/8” 1.182.06 2.25350/375 30/35
Outlet
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1Curves
Performance
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
RPEC-8 RPGC-8 RPIC-8 RPKC-8
Performance Curves
Pressure vs. Flow
RPCC 5000
RPEC 5000
RPGC 5000
RPIC 5000
RPKC
4000 4000
Typical Pressure Rise 4000 4000
P = psi
P = psi
P = psi
P = psi
3000 3000 3000 3000

5000 5000 2000 5000 2000 5000 5000
2000 2000
4000 4000 4000 4000
P = psi
4000 1000 1000 1000 1000

P = psi
P = psi
P = psi
P = psi
3000 3000 3000 3000 3000

0 12.5 25 37.5 50 0 25 50 75 100 0 75 100
2000 150 200 0 100 200 300 400
2000 2000 2000 2000
1000 1000 1000 1000 1000
0 5 10 15 20 25 0 10 20 30 40 50 0 20 40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400

Flow = GPM
■ MaximumFlow operating
= GPM pressure = 5000 psi= GPM
Flow Flow = GPM Flow = GPM
■
■ Will accept maximum pressure
Maximum operating pressure = 5000 psi at Port 2.
■
■ Backaccept
Will pressure on the tank
maximum port (port
pressure at Port2) 2.
is directly additive at a 1:1 ratio to the valve setting
■
■ Control
Back pilot flow
pressure on = RPEC-8:
the tank port to 102)inis3/min.,
7(port RPGC-8:
directly additive10atto 15 in
a 1:1
3/min., RPIC, RPKC-8: 15 to
ratio to the valve setting.
20 in3/min.
■ Maximum leakage = RPEC-8: 2 in3/min./1000 psi: RPGC-8: 3 in3/min./1000 psi, RPIC-8:
■ Typical
3 response time 10 ms. 3
4 in /min./1000 psi, RPKC-8: 5 in /min./1000 psi.
■
■
Maximum
With the -8leakage = RPCC,
control option, theRPEC:
main 2 in 3valve
stage /min./1000
shouldpsi,
firstRPGC: 3 in3/min./1000
be installed psi,torque
to the correct RPIC:value.
4
in 3 /min./1000 psi, RPKC: 5 in 3/min./1000 psi.
The T-8A pilot control valve should then be installed into the main stage valve to its required torque value.
RP ✱ C – ✱
8 ✱✱
Nominal
Nominal Base Control MinimumControl
Seal
Capacity Price Pressure
C
E 1225 GPM*
GPM $
+$31.90
40.20 L
8 Standard Screw
T-8A Cavity in +$
+$ 0.00
0.00 A
D 100 - 3000 psi +$
25 psi 0.00
+ $1.00 N Buna-N +$ 0.00
N Buna-N
E 25 GPM $ 36.20 hex body for
C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
G 50 GPM +$ 55.80 pilot operation W 100 psi +$ 0.00 V Viton
G 50 GPM $ 51.80 K Handknob
(Pilot valve to +$ 5.00 C 150 - 6000 psi +$ 2.00
I 100 GPM +$ 101.30 be ordered
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
separately)
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
W 150 - 4500 psi +$ 0.00

Visit www.sunhydraulics.com
** See pagefor
162detailed and complete technical
for information * Minimum information onon
setting 75 psi our
allfull line of products.
ranges.
on Control Options 14
Customer may specify pressure setting. US+$ 1.10Catalogue #999-901-243
Shortcut
Relief Valves
BALANCED POPPET, MODULATING ELEMENT WITH INTEGRAL
T-8A The -8 control option allows a pilot control valve to be incorporated directly
Cav
2 1 pilot, and hydraulic pilot operation. See Pilot Control Cartridges on page 121.
b
c
Locating
Shoulder
a Cartridge Dimensions
Outlet Capacity Cartridge Cavity a b c Torque
50 GPM RPGS – 8WN T - 3A 1.88 1 1/8” .69” 45/50
Inlet 1 100 GPM RPIS – 8WN T - 16A 2.44 1 1/4” .97 150/160
Performance Curves
RPGS-8 RPIS-8
4000 4000
3000 3000
P = psi
P = psi
2000 2000
1000 1000
0 25 50 75 100 0 125 150 175 200


■ Typical response time 10 ms
■ Control pilot flow = RPGS-8: 10 to 15 in3/min., RPIS-8: 15 to 20 in3/min.
■ Maximum leakage = 10 drops/min. at reseat
■ With the -8 control option, the main stage valve should first be installed to the correct torque value.

RP ✱ S – 8 ✱ ✱
Nominal Base Control** MinimumControl
Seal
G 50 GPM $ 65.80 8 T-8A Cavity in +$ 0.00 B 50 psi +$ 1.00 N Buna-N
hex body for
I 100 GPM $116.30 pilot operation W 100 psi +$ 0.00 V Viton
(Pilot valve to
be ordered
separately)
Relief Valves
VENTABLE, PILOT OPERATED, BALANCED PISTON
Relief Valves
PILOT+ OPERATED,- BALANCED PISTON
3
2 1
+ -
b c
2 1
c
b3 Cartridge Dimensions
Vent Locating Typical c Installation
Shoulder Capacity Cartridge Cavity a b Torque
Locating
Shoulder
Cartridge2.55
Dimensions
7.5 GPM RVBA – LAN T - 163A 1.22 3/4” 2.63 2.77 25/30
a Typical c Installation
2 15 GPM
Capacity RVCA – LAN Cavity
Cartridge T - 11A a 1.38 b7/8” 2.50 2.56 2.75 30/35
Torque
Outlet 30 GPM RVEA – LAN T - 2A 1.38 1 1/8” 2.81 2.88 3.06 45/50
a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 Inlet 1
60 GPM RVGA – LAN T - 17A 1.81 1 1/4” 3.28 3.31 3.53 150/160
25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet 120 GPM RVIA – LAN T - 19A 2.50 1 5/8” 3.94 4.09 4.19 350/375
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
Performance Curves 100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
RVBA RVCA200 GPM RVEA T - 18A
RPKC – LAN 3.13 RVGA
1 5/8” 2.81 RVIA
2.94 3.06 350/375
Performance Curves Typical Pressure Rise

5000 5000 5000
5000 5000
4000 4000 4000 4000 4000
P = psi
P = psi
P = psi
P = psi
P = psi
3000 3000 3000 3000

3000
2000 2000 2000 2000 2000
1000
5000 1000
5000 1000
5000 5000
1000 5000
1000
4000 4000 4000 4000
P = psi
4000 25
P = psi
0 10 20 30 40 50
P = psi
5 10 15 20 0
P = psi
P = psi
0 2 4 6 8 10 0 20 40 60 80 100 0 120 140 160 180 200

3000 Flow = GPM 3000 Flow = GPM 3000 Flow = GPM 3000 Flow = GPM 3000 Flow = GPM
2000 2000 2000 2000 2000
1000
■ Maximum
0 5 10 15 20 ■ 25 Pressure at port 3 (vent) controls the valve below its setting.

0 10 20 30 40 50 0 20 40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
■
■
Maximum
Control pilot operating pressureRVCA:
flow = RVBA, = 50007psi to10 in3/min.; RVEA: 10 to 15 in3/min.; RVGA, RVIA:
■ Will accept 3
15 to 20 in /min. maximum pressure at Port 2.
■
■ Back
Factory pressure setting established at 4isGPM
pressure on the tank port (port 2) directly additive at a 1:1 ratio to the valve setting.
■
Typical response time 10 established
ms. at 4 GPM
■
■ Typical
Maximum response
leakagetime 10 ms. RVCA: 2 in3/min./1000 psi, RVEA: 3 in3/min./ 1000 psi, RVGA:
= RVBA,
■ 4 in3/min./1000
Maximum leakage psi,=RVIA: in3/min./1000
RPCC,5 RPEC: psi
2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
in 3 /min./1000 psi,setting
RPKC:for 5 in 3
■ RVBA minimum all /min./1000
spring ranges psi.is 75 psi
■
■ RPCC
Will acceptminimummaximum settingpressure
for all spring
at portranges
2. is 75 psi
RP
RV ✱ C
A – ✱ ✱✱
Nominal
Nominal
Capacity Control**
Control** Adjustment
Adjustment Range
Range Seal
Seal
Capacity
C
B 12 GPM* $
7.5GPM* $ 31.90
47.70 L
L Standard
Standard Screw
Screw +$
+$ 0.00
0.00 A
A 100
100 -- 3000
3000 psi
psi +$
+$ 0.00
0.00 N
N Buna-N +$ 0.00
Buna-N
E 25 GPM
C 15 GPM $ 36.20
$ 47.70 C
C Tamper Resistant
Tamper Resistant +$
+$ 4.10
4.10 B
B 50 - 1500 psi
50 - 1500 psi +$
+$ 0.00
0.00 V
V Viton
Viton +$ 2.00
GE 50
30 GPM
GPM $
$ 51.80
65.10 K
K Handknob
Handknob +$
+$ 5.00
5.00 C
C 150
150 -- 6000
6000 psi
psi +$ 2.00
IG 100 GPM
60 GPM $ 97.30
$115.20 N
N 60 - 800 psi
60 - 800 psi +$ 1.00
K
I 200
120 GPM
GPM $187.00
$232.10 Q
Q 60
60 -- 400
400 psi
psi +$ 1.00
W 150 - 4500 psi +$ 0.00

Adjustment
A, B, C, Range
and W Options:
are standard set at 1000 psi.
A, B,
N C, and W
Option is are standard
standard set400
set at at 1000
psi. psi.
N Option is standard set at
Q Option is standard set400 psi. psi.
at 200
** See page 162 for information Q Option is setting
* Minimum standard75set
psiaton200
all psi.
ranges.
** See pageOptions
on Control 162 for information *Customer
Minimummaysetting 75 psipressure
specify on all ranges.
setting.
Relief Valves
MODULATING ELEMENT WITH RELIEF FUNCTION
+ -
3
1
2
b c
Vent Locating Typical c Installation
2.5 GPM RVBB – LAN T - 163A 1.22 3/4” 2.55 2.63 2.77 25/30
a
2 5 GPM RVCB – LAN T - 11A 1.38 7/8” 2.50 2.56 2.75 30/35
Outlet 10 GPM RVEB – LAN T - 2A 1.38 1 1/8” 2.81 2.88 3.06 45/50
20 GPM RVGB – LAN T - 17A 1.81 1 1/4” 3.28 3.31 3.53 150/160
Inlet 1
40 GPM RVIB – LAN T - 19A 2.50 1 5/8” 3.94 4.09 4.19 350/375
Performance Curves
RVBB RVCB RVEB RVGB RVIB
Typical Compensator Differentials
Pressure Differential
400 400 400 400 400
Port 1 to 3 (psi)
Port 1 to 3 (psi)
Port 1 to 3 (psi)
Port 1 to 3 (psi)
Port 1 to 3 (psi)
Bypass Flow Bypass Flow 60 GPM Bypass Flow Bypass Flow
300 Port 1 to 2 300 Port 1 to 2 300 300 Port 1 to 2 300 Port 1 to 2
40 GPM 120 GPM
10 GPM 20 GPM 120 GPM
200 200 15 GPM 200 10 GPM
200 200 80 GPM
5 GPM 10 GPM 60 GPM
100 1 GPM 100 100 Bypass Flow 100 20 GPM 100 60 GPM
5 GPM
Port 1 to 2
0 0 0 0 0
0 600 1200 1800 2400 3000 3600 0 600 1200 1800 2400 3000 3600 0 600 1200 1800 2400 3000 3600 0 600 1200 1800 2400 3000 3600 0 600 1200 1800 2400 3000 3600
Load Pressure (psi) Load Pressure (psi) Load Pressure (psi) Load Pressure (psi) Load Pressure (psi)

■ Back pressue on the tank port (port 2) is directly additive at a 1:1 ratio to the valve setting.
■ Factory pressure setting established at 4 GPM
■ Maximum leakage = RVBB, RVCB: 2 in3/min./1000 psi, RVEB: 3 in3/min./ 1000 psi, RVGB:
4 in3/min./1000 psi, RVIB: 5 in3/min./1000 psi

RV ✱ B – ✱ ✱ ✱
Capacity
B 2.5 GPM* $ 59.30 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N
C 5 GPM $ 59.30 C Tamper Resistant +$ 4.10 B 100 - 1500 psi* +$ 0.00 V Viton
E 10 GPM $ 84.30 K Handknob +$ 5.00 C 100 - 6000 psi
G 20 GPM
I 40 GPM
* For RVCB, the bias pressure is 60 psi.

A, B, and C are standard set at 1000 psi.
Relief Valves
VENTABLE, PILOT OPERATED, BALANCED POPPET
3
2 1
b c
3
Vent Cartridge Dimensions
Locating
2 a 30 GPM RVES – LAN T - 2A 1.38 1 1/8” 2.81 2.88 3.06 45/50
Outlet
50 GPM RVGS – LAN T - 17A 1.81 1 1/4” 3.28 3.31 3.53 150/175
Inlet 1
Performance Curves
RVES RVGS
Typical Pressure Rise Vented Pressure Typical Pressure Rise Vented Pressure
4000 200 4000 200
3000 150 3000 150

P = psi
P = psi
P = psi
P = psi
C, W, A
C, W, A
2000 100 2000 100
B
1000 50 B 1000 50
0 0 0 0
0 25 50 75 100 0 15 30 45 60 0 25 50 75 100 0 15 30 45 60
■ Maximum operating pressure = 5000 psi.

■ Will accept maximum pressure at port 2
■ Pressure at port 3 (vent) controls the valve below its setting.
■ Maximum leakage at reseat = 10 drops/min.
■ Typical response 10 ms
■ Control pilot flow = RVES: 10 to 15 in3/min, RVGS: 15 to 20 in3/min.

RV ✱ S – ✱ ✱ ✱
Nominal
E 30 GPM +$ 75.10 C Tamper Resistant +$ 4.10 A 100 - 3000 psi +$ 0.00 N Buna-N
Factory Set
G 50 GPM +$130.50 B 50 - 1500 psi +$ 0.00 V Viton
K Handknob
C 150 - 6000 psi
L Standard Screw
Adjustment N 60 - 800 psi
Q 60 - 400 psi
W 100 - 4500 psi

A, B, C and W are standard set at 1000 psi.
Q option is standard set at 200 psi.
** See page 162 for information
on Control Options Customer may specify pressure settings.
Relief Valves
VENTABLE, PILOT OPERATED, BALANCED PISTON WITH EXTERNAL DRAIN
+ -
4 3
2 1
b
4 Capacity Cartridge Cavity a b Torque
Drain Model Code L C K (lb. ft.)
3 15 GPM RVCD – LAN T - 21A 1.38 7/8” 3.09 3.15 3.34 30/35
Vent Locating
Shoulder 30 GPM RVED – LAN T - 22A 1.38 1 1/8” 3.44 3.50 3.69 45/50
60 GPM RVGD – LAN T - 23A 1.81 1 1/4” 3.93 3.99 4.19 150/160
2 a 120 GPM RVID – LAN T - 24A 2.50 1 5/8” 4.78 4.90 5.03 350/375
Outlet
Inlet 1
Performance Curves
RVCD RVED RVGD RVID
Vented Pressure
200 200 200 200
150 C&W C&W

P = psi
150 150 150

P = psi
P = psi
P = psi
C&W
100 100 C&W 100 100
A A
50 A 50 A 50 50 B
B D&E B
D&E B D&E
D&E
0 5 10 15 20 0 10 20 30 40 0 25 50 75 100 0 50 100 150 200

5000 5000 5000 5000
4000 4000 4000 4000
P = psi
P = psi
P = psi
P = psi
3000 3000 3000 3000

2000 2000 2000 2000
1000 1000 1000 1000
0 10 20 30 40 50 0 20 40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400


■ Pressure at port 4 is directly additive to the valve setting at a 1:1 ratio and should not exceed 5000 psi
■ Control pilot flow = RVCD: 7 to10 in3/min.; RVED: 10 to 15 in3/min.; RVGD, RVID: 15 to 20 in3/min.
■ Maximum leakage = RVCD: 2 in3/min./1000 psi, RVED: 3 in3/min./1000 psi, RVGD: 4 in3/min./1000
psi, RVID: 5 in3/min./1000 psi.

RV ✱ D – ✱ ✱ ✱
Capacity
C 15 GPM $ 73.60 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N
E 30 GPM $ 102.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton
G 60 GPM $ 181.00 K Handknob +$ 5.00 C 150 - 6000 psi
I 120 GPM $ 335.50 D 25 - 800 psi
E 25 - 400 psi
W 150 - 4500 psi
**See page 162 for information E Option is standard set at 200 psi.
Relief Valves
VENTABLE, BALANCED PISTON, MODULATING ELEMENT WITH EXTERNAL
DRAIN AND INTEGRAL PILOT CONTROL ELEMENT

b 3 into the end of the modulating element via the T-8A cavity. These pilot control
4 T-8A cartridges are sold separately and include electro-proportional, solenoid, air
Cav
pilot, and hydraulic pilot operation. See Pilot Control Cartridges on page 121.
4 c 1
2
Drain
3
Vent Locating Cartridge Dimensions
Capacity Cartridge Cavity a b c Torque
2 a
Outlet 15 GPM RVCD – 8WN T - 21A 1.38 7/8 1.78 30/35
30 GPM RVED – 8WN T - 22A 1.38 1 1/8 2.00 45/50
Inlet 1
60 GPM RVGD – 8WN T - 23A 1.814 1 1/4 2.59 150/160
120 GPM RVID – 8WN T - 24A 2.50 1 5/8 3.16 350/375
Performance Curves
RVCD-8 RVED-8 RVGD-8 RVID-8

Vented Pressure
200 200 200 200
150 C&W C&W

P = psi
150 150 150

P = psi
P = psi
P = psi
C&W
100 100 C&W 100 100
A A
50 A 50 A 50 50 B
B D&E B
D&E B D&E
D&E
0 5 10 15 20 0 10 20 30 40 0 25 50 75 100 0 50 100 150 200

5000 5000 5000 5000
4000 4000 4000 4000
P = psi
P = psi
P = psi
P = psi
3000 3000 3000 3000

2000 2000 2000 2000
1000 1000 1000 1000
0 5 10 15 20 0 10 20 30 40 0 20 40 60 80 0 40 80 120 160

■ Pressure at port 4 is directly additive to the valve setting at a 1:1 ratio and should not exceed 5000 psi
■ Control pilot flow = RVCD: 7 to10 in3/min.; RVED: 10 to 15 in3/min.; RVGD, RVID: 15 to 20 in3/min.
■ Maximum leakage = RVCD: 2 in3/min./1000 psi, RVED: 3 in3/min./1000 psi, RVGD: 4 in3/min./1000
psi, RVID: 5 in3/min./1000 psi.

RV ✱ D – 8 ✱ ✱
Nominal Base Control Minimum Control Seal
C 15 GPM $ 73.60 8 T-8A Cavity in D 27 psi +$ 1.00 N Buna-N
hex body for
E 30 GPM $102.20 pilot operation W 100 psi +$ 0.00 V Viton
(Pilot valve to
G 60 GPM $181.00 be ordered
separately)
I 120 GPM
Sequence Cartridge Valves
Cartridge Type Page
Pilot Operated, Balanced Piston 22

2 1
3
T-8A
Cav
Externally Drained, Balanced Piston,
23
2 1 Modulating Element
Air Pilot
3 Air Controlled, Pilot Operated, Balanced Piston 24

2 1
2 1
Direct Acting without Reverse Flow Check 25
2 1 Direct Acting with Reverse Flow Check 26
Pilot Operated, Kick-down 27

2 1

Sequence
Relief Valves
Valves
PILOT OPERATED,
OPERATED, BALANCED
BALANCED PISTON
PISTON
FullAdjustment
Full Adjustment55Turns
Turns
++ -- 3
2 11
c
b c
b
Locating
Dimensions
Cartridge
Drain Locating Typical cc Installation
Capacity
Capacity Cartridge
Cartridge Cavity
Cavity a a bb Torque
Torque
Model Code L
L CC K K (lb.(lb.
ft.)ft.)
Model Code
a 127.5 GPM
GPM RSBC
RPCC – LAN T - T162A
– LAN - 163A 1.221.22 3/4”
3/4” 2.55
2.11 2.63
2.17 2.77
2.31 25/30
25/30
a
22 2515 GPM
GPM RSDC
RPEC – LAN T - T10A
– LAN - 11A 1.561.38 7/8”
7/8” 2.50
2.00 2.56
2.06 2.75
2.25 30/35
30/35
Outlet
Sequence
5030 GPM
GPM RSFC –
RPGC – LANLAN T - T3A- 2A 1.881.38 1 11/8”
1/8” 2.81
2.12 2.88
2.18 3.06
2.38 45/50
45/50
60 GPM
100 GPM RSHC
RPIC – LAN T - T16A
– LAN - 17A 2.441.81 1 1/4”
1 1/4” 3.28
2.44 3.31
2.47 3.53
2.69 150/160
150/160
Inlet 1 1
Inlet
120
200 GPM
GPM RSJC
RPKC – LAN T - 18A19A
– LAN T - 3.132.50 1 5/8”
1 5/8” 3.94
2.81 4.09
2.94 4.19
3.06 350/375
350/375
Performance Curves
Performance Curves
RSBC
RPCC RSDC
RPEC RSFC
RPGC RSHC
RPIC RSJC
RPKC
Pressure Drop
Typical Sequenced
Pressure RiseOpen
200 200
5000 200
5000 200
5000 200
5000
5000
psi
4000 4000
psi
150 150
4000 150
4000 150 150
psi
psi
4000
psi
PP==psi
PP = psi
P == psi
P==psi
PP==psi
3000 3000 3000 3000 3000

100 100 100 100 100
2000 2000 2000 2000 2000
P
50 50 50 50 50
1000 1000 1000 1000 1000
0 40 80 120 160 200

0 25 4
10 6
15 8
20 10
25 00 10
5 20 10 30 1540 50
20 00 20
10 40 20 60 30 80 100
40 0 20 40 60 80 00 80
40 16080 240 120
320 160
400
Flow = GPM
Flow GPM Flow== GPM
GPM Flow == GPM
GPM Flow = GPM Flow == GPM
GPM
Flow Flow Flow = GPM Flow
■
■ Maximum
Maximum operating
operating pressure
pressure = = 5000
5000 psi
psi
■
■ Will accept maximum pressure at
Maximum leakage = RSDC: 2 in3/min./1000 Port 2. psi, RSFC: 3 in3/min./1000 psi, RSHC: 4 in3/min./1000 psi
■ Back 5 in 3/min./1000
RSJC:pressure on the tank
psi.port (port 2) is directly additive at a 1:1 ratio to the valve setting.
Typical response time 10 established
ms at 4 GPM
■ Typical
Pressureresponse
at port 3time 10 ms.additive to the valve setting at a 1:1 ratio and should not exceed 5000 psi.
is directly
Maximum leakage = toRPCC, RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■
Pilot flow continues increase as the pressure at port 1 (inlet), relative to the pressure at port 3 (drain),
in 3/min./1000 psi, RPKC: 5 in3/min./1000 psi.
rises above the valve setting.
■ RPCC
RSBC minimum setting for allpsi
is 75 spring ranges
for all springis ranges.
75 psi
RP
RS ✱ C – ✱ ✱ ✱
Nominal
Nominal
Capacity
C
B 12 GPM* $
7.5GPM* $ 31.90
43.10 L
L Standard
Standard Screw
Screw +$
+$ 0.00
0.00 A
A 100
100 -- 3000
3000 psi
psi +$
+$ 0.00
0.00 N Buna-N +$ 0.00
N Buna-N
E
D 25
15 GPM
GPM $
$ 36.20
43.10 C
C Tamper Resistant +$
Tamper Resistant +$ 4.10
4.10 B
B 50
50 -- 1500
1500 psi
psi +$
+$ 0.00
0.00 V
V Viton
Viton +$ 2.00
G
F 50
30 GPM
GPM $
$ 51.80
61.60 K
K Handknob
Handknob +$
+$ 5.00
5.00 C
C 150
150 -- 6000
6000 psi
psi +$ 2.00
IH 100 GPM
60 GPM $ 97.30
$115.60 N
N 60
60 -- 800
800 psi
psi +$ 1.00
K
J 200
120 GPM
GPM $187.00
$227.10 Q
Q 60
60 -- 400
400 psi
psi +$ 1.00
W 150 - 4500 psi +$ 0.00
Adjustment
Adjustment Range
Range Options:
Options:
A, B,
A,C,
B,and W are
C, and standard
W are set at
standard set1000 psi.psi.
at 1000
Q Option is standard
Q Option set at
is standard set200 psi.psi.
at 200
**
** See
See page
page 162
162 for
for information
information ** Minimum
Minimum setting
setting 75
75 psi
psi on
on all
all ranges.
ranges.
on
on Control
Control Options
Options Customer
Customer may
may specify
specify pressure
pressure setting.
setting. +$ 1.10
Visit www.sunhydraulics.com for
for detailed
detailed and
and complete
complete technical
technical information
information on
on our
our full
full line
line of
of products.
products.
22
6 US Shortcut
US Shortcut Catalogue
Catalogue #999-901-243
#999-901-243
Sequence Valves
EXTERNALLY DRAINED, BALANCED PISTON, MODULATING ELEMENT
3 cartridges are sold separately and include electro-proportional, solenoid, air
T-8A
Cav pilot, and hydraulic pilot operation. See Pilot Control Cartridges on page 121.
b
2 1
c
3
Drain
Locating
Shoulder
2 a Capacity Cartridge Cavity a b c Torque
Sequence Model Code (lb. ft.)
15 GPM RSDC – 8WN T - 11A 1.38 7/8 1.19 30/35
Inlet 1 30 GPM RSFC – 8WN T - 2A 1.38 1 1/8 1.38 45/50

60 GPM RSHC – 8WN T - 17A 1.81 1 1/4 1.81 150/160
120 GPM RSJC – 8WN T - 19A 2.50 1 5/8 2.31 350/375
Performance Curves
RSDC-8 RSFC-8 RSHC-8 RSJC-8
5000 5000 5000 5000
4000 4000 4000 4000
P = psi
P = psi
P = psi
P = psi
3000 3000 3000 3000
2000 2000 2000 2000
1000 1000 1000 1000
0 5 10 15 20 0 10 20 30 40 0 20 40 60 80 0 40 80 120 160
■ Pressure at port 3 is directly additive at a 1:1 ratio to the valve setting and should not exceed 5000 psi.
■ Control pilot flow = RSDC-8: 7 to 10 in3/min., RSFC-8: 10 to 15 in3/min., RSHC, RSJC-8:
15 to 20 in3/min.
■ Maximum leakage = RSDC-8: 2 in 3/min./1000 psi: RSFC-8: 3 in3/min./1000 psi, RSHC-8:
4 in3/min./1000 psi, RSJC-8: 5 in3/min./1000 psi.
■ With the -8 control option, the main stage valve should first be installed to the correct torque value. The
T-8A pilot control valve should then be installed into the main stage valve to its required torque value.

RS ✱ C – 8 ✱ ✱
Capacity Price Pressure Seal
D 15 GPM $ 48.90 8 T-8A Cavity in D 25 psi +$ 1.00 N Buna-N

hex body for
F 30 GPM $ 66.60 pilot operation W 100 psi +$ 0.00 V Viton
(Pilot valve to
H 60 GPM $120.60 be ordered
separately)
J 120 GPM
Sequence Valves
AIR CONTROLLED, PILOT OPERATED, BALANCED PISTON
Air Pilot
Air Pilot Port
b 2 1
c
3
Drain Locating Cartridge Dimensions
Shoulder
Model Code A B (lb. ft.)
a
30 GPM RSFE – ABN T - 2A 1.38 1 1/8” 2.00 - 45/50
2
Sequence 60 GPM RSHE – BBN T - 17A 1.81 1 1/4” - 2.47 150/160
120 GPM RSJE – BBN T - 19A 2.50 1 5/8” - 3.12 350/375
Inlet 1
Performance Curves
RSFE RSHE RSJE
Pressure Drop Sequenced Open
200 400 400
150 300 300

P = psi
P = psi
P = psi
100 200 200
50 100 100
0 10 20 30 40 0 25 50 75 100 0 50 100 150 200

■ Pilot ratio, air to hydraulic 1:20

■ Maximum leakage = RSFE: 3 in3/min./1000 psi , RSHE: 4 in3/min./1000 psi,
RSJE: 5 in3/min./1000 psi.

RS ✱ E – ✱ B ✱
Nominal Control Adjustment Range Seal
Capacity
F 30 GPM $130.60 Available for RSFE only B 50 - 1500 psi +$ 0.00 N Buna-N
H 60 GPM $176.30 A 1/4" NPTF V Viton

Pilot Port at
J 120 GPM $318.90 end of Cartridge*
Available for RSHE, RSJE only
B SAE-4
Pilot Port at
end of Cartridge*
Relief Valves
PILOT OPERATED,
Sequence Valves BALANCED PISTON
DIRECT
Full AdjustmentACTING
5 Turns WITHOUT REVERSE FLOW CHECK
+ -
+ - 3
2 1
c
2 1
b
Locating
Shoulder
b c Cartridge Dimensions
Model Code Cartridge L
DimensionsC K (lb. ft.)
a 12 GPM RPCC Typical
– LAN T - 162A 1.22 3/4” 2.11 c
2.17 2.31 Installation
25/30
2 Locating 25 GPM RPEC – LAN
Model Code T - 10A 1.56 7/8” L
2.00 2.06 C 2.25 (lb.30/35
ft.)
Drain
Outlet Shoulder
5015 GPM
GPM SXCA
RPGC – LAN T - T3A- 11A
– LAN 1.38
1.88 7/8”
1 1/8” 3.09
2.12 2.183.15 2.38 30/35
45/50
a 10030GPM
GPM SXEA
– LAN - 2A 1.38
2.44 1 11/4”
1/8” 3.47
2.44 2.473.53 2.69 45/50
150/160
2 Inlet 1
Sequence 200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
1
Inlet Curves
Performance
Performance Curves
5000
SXCA 5000
SXEA 5000 5000
5000

4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
3000 3000 3000 3000 3000

400 400 2000
2000 2000 2000 2000
300 1000
P = psi
1000 1000 300 1000 1000

P = psi
0 5 10 15 20 25 0 10 20 200
30 40 50 0 20 40 200
60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
Flow = GPM Flow = GPM Flow = 100
GPM Flow = GPM Flow = GPM
100
0 5 10 15 0 10 20 30
■ Will accept maximum pressure
Flow = GPMat Port 2. Flow = GPM
■
■ Back pressure
Maximum on the pressure
operating tank port=(port
50002)psi
is directly additive at a 1:1 ratio to the valve setting.
■
Maximum valve leakage at reseat = 10 drops/min.
■
■ Typical
Typical response
response time
time 10
2 msms.
■ Maximum leakage = RPCC, 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
RPEC: 2tointhe
■ Pressure at port 3 is directly additive valve setting at a 1:1 ratio and should not exceed 5000 psi.
RP
SX ✱ C
A – ✱ ✱✱
Nominal
C 12
15 GPM*
GPM $ 31.90
45.10 L Standard Screw +$ 0.00 A 100
500 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
E 25
30 GPM $ 36.20
65.60 C Tamper Resistant +$ 4.10 B 50
300- 1500
- 1500psi
psi +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 K Handknob +$ 5.00 C 150
2000- 6000 psi +$ 2.00
- 6000psi
I 100 GPM $ 97.30 N
D 60
200- 800
- 800psi
psi +$ 1.00
K 200 GPM $187.00 Q
W 60
800- 400 psipsi
- 4500 +$ 1.00
W 150 - 4500 psi +$ 0.00

A, B, and W are standard set at 1000 psi.
C Option is standard set at 2000 psi.
** See page 162 for information D Option is standard set at 400 psi.
on Control Options
Visit www.sunhydraulics.com Customerinformation
for detailed and complete technical may specifyon
pressure
our fullsetting.
line of products.
Sequence
Relief Valves
Valves
DIRECT
PILOT ACTING WITH
OPERATED, REVERSEPISTON
BALANCED FLOW CHECK
+ - 3
+ -
2 1
2 1
c
b c
b
Locating
3 Capacity Typical
Cartridge Cavity a b c Installation
Torque
Drain Locating Capacity Cartridge
Model Code Cavity a b L C (lb.Torque
ft.)
Shoulder Model Code L C K (lb. ft.)
a 15 GPM SCCA – LAN T - 11A 1.38 7/8” 3.09 3.15 30/35
12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
22 a 30 GPM SCEA – LAN T - 2A 1.38 1 1/8” 3.47 3.53 45/50
25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
Sequence 60 GPM SCGA – LAN T - 17A 1.81 1 1/4” 3.94 4.00 150/160
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
120 GPM SCIA – LAN T - 19A 2.50 1 5/8” 4.72 4.92 350/375
Inlet 1 100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
Performance Curves
RPCC SCCA RPEC SCEA RPGC SCGA RPIC SCIA RPKC

Free Flow to Pressure Drop Sequenced Open
300 300 300 300
5000 5000 5000 5000 5000
P = psi
P = psi
P = psi
P = psi
200 4000 200 4000 200 4000 200 4000

P = psi
4000
P = psi
Free Flow Free Flow
P = psi
Free Flow
P = psi
P = psi
Free Flow
3000 3000 3000 3000 3000
100 100 100 2000 100
2000 2000 2000 2000
1000 1000 1000 1000 1000
0 5 10 15
0 203 25
6 9 0 12 1015 20 30 0 406 5012 18 0 24 2030 40 600 12 100 24
80 36 0 48 4060 80 1200 24 200 48
160 72 0 96 80120 160 240 320 400
Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM Flow = GPM
■
■ Maximum
Maximum operating
operating pressure
pressure == 5000
5000 psi
psi
■
■ Will
Maximum valve leakage at reseat Port
accept maximum pressure at = 10 2.
drops/min.
■
■ Back pressure
Free flow checkoncracking
the tank pressure
port (port= 2)
40ispsidirectly additive at a 1:1 ratio to the valve setting.
■
Typical response time 2 ms established at 4 GPM
■
■ Typical response time 10 ms.additive to the valve setting at a 1:1 ratio and should not exceed 5000 psi.
Pressure at port 3 is directly
■
■ Maximum
Reseat leakage = RPCC,
exceeds 85% of cracking RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
pressure.
3 3
RP
SC ✱ C
A – ✱ ✱✱
Nominal
Nominal
Capacity
E 30 GPM $ 78.50 C Tamper Resistant +$ 4.10 B 300 - 1500 psi +$ 0.00 V Viton
G 60 GPM $133.90 C 2000 - 6000 psi
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
I 120 GPM $303.50 D 200 - 800 psi
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
W 800 - 4500 psi
W 150 - 4500 psi +$ 0.00

Adjustment
Q Option is Range
standardOptions:
set at 200 psi.
** See page 162 for information A, B, andsetting
* Minimum W are75 standard set ranges.
psi on all at 1000 psi.
on Control Options C Option
Customer is standard
may set at 2000
specify pressure psi.
setting. +$ 1.10
Sequence Valves
PILOT OPERATED, KICK-DOWN
+ - 3
2 1
b c
Drain Locating Typical c Installation
a 15 GPM SQDB – LAN T - 11A 1.38 7/8” 2.50 2.56 2.75 30/35
2 30 GPM SQFB – LAN T - 2A 1.38 1 1/8” 2.81 2.88 3.06 45/50
Sequence
60 GPM SQHB – LAN T - 17A 1.81 1 1/4” 3.28 3.31 3.53 150/160
Inlet 1 120 GPM SQJB – LAN T - 19A 2.50 1 5/8” 3.94 4.09 4.19 350/375
Performance Curves
SQDB SQFB SQHB SQJB
150 150 300 300
P = psi
P = psi
P = psi
P = psi
C&W C&W
100 100 200 200
C&W C&W
A A B
50 A 50 100
B A B 100
B
D&E
D&E D&E D&E
0 3 6 9 12 15 0 6 12 18 24 30 0 20 40 60 80 100 0 40 80 120 160 200


■ Maximum leakage = SQDB: 2 in3/min./1000 psi , SQFB: 3 in3/min./1000 psi , SQHB:
4 in3/min./1000 psi SQJB: 5 in3/min./1000 psi
■ Typical response time 25 ms
■ Pressure at port 3 is directly additive to the valve setting at a 1:1 ratio and should not exceed 5000 psi.
■ To reset valve, flow through the cartridge must cease.

SQ ✱ B – ✱ ✱ ✱
Capacity
D 15 GPM $ 57.80 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N
F 30 GPM $ 80.30 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton
H 60 GPM $144.60 K Handknob +$ 5.00 C 150 - 6000 psi
J 120 GPM $267.40 D 25 - 800 psi
E 25 - 400 psi
W 150 - 4500 psi

Sequence Valves
NOTES

Reducing and Reducing/Relieving
Cartridge Valves
Cartridge Type Page
Pilot Operated Reducing 30

2 1
Pilot Operated Reducing/Relieving 31

2 1
Direct Acting Reducing/Relieving 32

2 1
4
Pilot Operated Reducing/Relieving, Externally
33
3
2 1
Drained
4
3
Pilot Operated Reducing/Relieving, Ventable 34
2 1
Air Pilot
3 Air Controlled, Pilot Operated Reducing 35

2 1
Air Pilot
3 Air Controlled, Pilot Operated

36
Reducing/Relieving
2 1
3
T-8A
Cav
Modulating Element with Integral Pilot
37
2 1 Control Cavity
T-8A
3
Cav
3-Way, Modulating Element with Integral
38
2 1
Pilot Control Cavity
3
4
T-8A
Cav 3-Way, Externally Drained, Modulating Element
39
2 1
with Integral Pilot Control Cavity
Electro-proportional, Direct Acting

40
Reducing/Relieving
2 3
1
Electro-proportional, Direct Acting

41
with Low Leakage
2 3

Relief Valves
PILOT OPERATED,
Reducing BALANCED
and Reducing/Relieving PISTON
Valves
PILOT OPERATED
Full Adjustment 5 Turns REDUCING
+ -
+ - 3
2 1
c
b 2 1
b c Locating
Shoulder
Model Code L
Cartridge DimensionsC K (lb. ft.)
Drain Locating
a Shoulder 12Capacity
GPM Typical
RPCCCartridge
– LAN T - 162A 1.22 a 3/4” 2.11 c
2.17 2.31 Installation
25/30
Cavity b Torque
2 Model Code L C K (lb.30/35
ft.)
25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25
Outlet
a 505GPM
GPM PBBB
RPGC – LAN T - T3A- 163A
– LAN 1.881.22 3/4”
1 1/8” 2.55
2.12 2.63
2.18 2.77
2.38 25/30
45/50
2
Inlet 10010GPM
GPM PBDB
– LAN - 11A 2.441.38 7/8”
1 1/4” 2.50
2.44 2.56
2.47 2.75
2.69 30/35
150/160
Inlet 1 20 GPM PBFB – LAN T - T18A
- 2A
200 GPM RPKC – LAN 3.131.38 1 1/8”
1 5/8” 2.81
2.81 2.88
2.94 3.06
3.06 45/50
350/375
1 40 GPM PBHB – LAN T - 17A 1.81 1 1/4” 3.28 3.31 3.53 150/160
ReducedCurves
Performance Pressure
80 GPM PBJB – LAN T - 19A 2.50 1 5/8” 3.94 4.09 4.19 350/375
Performance Curves
PB*B PBDB PBFB PBHB
5000
PBJB
5000
5000 5000 5000
4000 Regulated Pressure
4000 4000 4000
P = psi P = psi
4000
P = psi P = psi
P = psi P = psi
P = psiP = psi
P = psiP = psi
3000 3000 3000 3000 3000

2000 2000 2000 2000 2000
2000 2000 2000 2000 2000
1500 1500 1500 1500 1500
1000 1000 1000 1000 1000
1000 1000 1000 1000 1000
0 5 10 15 20 25 0 10 20 30 40 50 0 20 40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
500 Flow = GPM 500 Flow = GPM 500 Flow = GPM 500 Flow = GPM 500 Flow = GPM
0 2.50
Flow = GPM
5 ■ 7.5 Maximum
0 5operating
10
Flow = GPM
pressure
15 =0 5000Flow
10psi 20
= GPM
30 0 10 20 30 40 50
Flow = GPM
60 0 20 40 60 80 100 120
Flow = GPM
■ Factory pressure setting established at blocked control port (deadhead)
■ Factory pressure settings established at 4 GPM3
■ Control pilot flow = PBBB, PBDB: 7 to 10 in /min., PBFB: 10 to 15 in3/min., PBHB, PBJB:
■ Typical
15 to 20response
in3/min. time 10 ms.
Maximum 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
at leakage
port 3 is=directly
RPCC, additive
RPEC: 2tointhe
■
■ Pressure
3 3
valve setting at a 1:1 ratio and should not exceed 3000 psi.
RP
PB ✱ C
B – ✱ ✱✱
Nominal
Nominal
Capacity Control**
Adjustment Range
Range Seal
Seal
Capacity
C
B 12 GPM*
5 GPM* $
$ 31.90
42.50 L
L Standard
Standard Screw
Screw +$
+$ 0.00
0.00 A
A 100
100 -- 3000
3000 psi
psi +$
+$ 0.00
0.00 N
N Buna-N +$ 0.00
Buna-N
E
D 25
10 GPM
GPM $
$ 36.20
42.20 C
C Tamper Resistant
Tamper Resistant +$
+$ 4.10
4.10 B
B 50 - 1500 psi
50 - 1500 psi +$
+$ 0.00
0.00 V
V Viton
Viton +$ 2.00
G
F 50
20 GPM
GPM $
$ 51.80
60.20 K
K Handknob
Handknob +$
+$ 5.00
5.00 C
N 150
60 - -800
6000
psipsi +$ 2.00
IH 100 GPM
40 GPM $ 97.30
$113.80 N
Q 60
60 -- 800
400 psi
psi +$ 1.00
KJ 200 GPM
80 GPM $187.00
$243.10 Q
W 60
150- -400 psipsi
4500 +$ 1.00
W 150 - 4500 psi +$ 0.00
Adjustment
Adjustment Range
Range Options:
Options:
A,
AllB, C,standard
are and W are setstandard set at 1000 psi.
at 200 psi.
Maximum pressure differentials for spring ranges:
Q Option
A and is standard
B are 3000 set
psi.at 200 psi.
** See page 162 for information * Minimum
N and Qsetting 75 psi.
are 2000 psi on all ranges.
on Control Options Customer
W is 5000maypsispecify pressure setting.
inlet pressure. +$ 1.10
Relief Valves
Reducing and Reducing/Relieving
PILOT OPERATED, BALANCED Valves
PISTON
PILOT OPERATED
REDUCING/RELIEVING
+ - 5 Turns
Full Adjustment
+ - 3
2 1
c
2 1
bb c
Locating
Shoulder
3 Typical Cartridge Dimensions c Installation
Tank Locating Capacity Cartridge Cavity a b Torque
Shoulder Model Typical
Code L c C Installation
(lb. ft.) K
12 GPM RPCC –
ModelLANCode T - 162A 1.22 3/4” L2.11 C 2.17 K 2.31 25/30
(lb. ft.)
2 a 2510
GPM
GPM PPDB
RPEC – LAN T - 10A
– LAN T - 11A 1.56
1.38 7/8” 2.00
2.50 2.562.06 2.75 2.25 30/35
30/35
2
Outlet
Inlet 5020 GPM
GPM RPGC – LAN
PPFB – LAN T - 3A
T - 2A 1.38
1.88 1 1/8” 2.81
2.12 2.882.18 3.06 2.38 45/50
45/50
10040GPM
GPM RPIC – LAN
PPHB – LAN T - 16A
T - 17A 2.44
1.81 1 1/4” 2.44
3.28 3.312.47 3.53 2.69 150/160
150/160
Inlet 11
20080GPM
GPM RPKC – LAN
PPJB – LAN T - 18A
T - 19A 3.13
2.50 1 5/8” 2.81
3.94 4.092.94 4.19 3.06 350/375
350/375
Reduced Pressure
Performance Curves
RPCC
Performance Curves RPEC RPGC RPIC RPKC
PPDB PPFB PPHB
Typical Pressure Rise PPJB
5000 5000 Regulated Pressure
5000 5000 5000
4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
Relieving Reducing Relieving Reducing Relieving Reducing Relieving Reducing

3000 2000 3000 2000 3000 2000 3000 2000 3000
2000 2000 2000 2000 2000
1500 1500 1500 1500
P = psi
P = psi
P = psi
P = psi
1000 1000 1000 1000 1000
1000 1000 1000 1000
0 5 10 15 20 25 0 10 20 30 40 50 0 20 40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
Flow = GPM
500 Flow = 500
GPM Flow = GPM
500 Flow = 500
GPM Flow = GPM
0 0 0 0
-10 -5 0 5 10 15 -20 -10 0 10 20 30 -40 -20 0 20 40 60 -80 -140 0 40 80 120
FlowMaximum operating pressure = 5000 psi
■
= GPM Flow = GPM Flow = GPM Flow = GPM
■ Factory pressure settings established at3 4 GPM
■ Control pilot flow = PPDB: 7 to 10 in /min., PPFB: 10 to 15 in3/min., PPHB, PPJB:
■ Typical
15 to 20response
in3/min. time 10 ms.
■
■ Pressure atleakage
port 3 is=directly
RPCC, additive
RPEC: 2tointhe valve setting at a 1:1 ratio and should not exceed 3000 psi.
RP
PP ✱ C
B – ✱ ✱✱
Nominal
Capacity
C
D 1210 GPM*
GPM $
$ 31.90
51.00 L
L Standard
Standard Screw
Screw +$
+$ 0.00
0.00 A
A 100
100 -- 3000
3000 psi
psi +$
+$ 0.00
0.00 N Buna-N +$ 0.00
N Buna-N
E
F 25
20 GPM $ 36.20
73.40 C Tamper Resistant +$ 4.10 B 50 --1500
1500 psi
psi +$ 0.00 V Viton +$ 2.00
G
H 50
40 GPM $ 51.80
$136.80 K Handknob +$ 5.00 C
N 150
60 - -800
6000
psipsi +$ 2.00
IJ 100 GPM
80 GPM $ 97.30
$268.60 N
Q 60 - 800
400 psi +$ 1.00
K 200 GPM $187.00 Q
W 60
150- 400 psipsi
- 4500 +$ 1.00
W 150 - 4500 psi +$ 0.00

All are standard
Adjustment Range setOptions:
at 200 psi.
Maximum
A, pressure
B, C, and differentials
W are standard for1000
set at spring
psi.ranges:
A and is
N Option B standard
are 3000 setpsi.at 400 psi.
N and is
Q Option Qstandard
are 2000set psi.at 200 psi.
** See
** See page
page 162
162 for
for information
information W is 5000
* Minimum psi inlet
setting pressure.
75 psi on all ranges.
6
Visit www.sunhydraulics.com for detailed and complete technical US Shortcut Catalogue #999-901-243
information on our full line of products.
Relief Valves
PILOT OPERATED,
Reducing BALANCED
and Reducing/Relieving PISTON
Valves
DIRECT
Full AdjustmentACTING
5 Turns REDUCING/RELIEVING
+ -
3
+ -
2 1
c
2 1
b
b c Locating
Shoulder
Capacity Cartridge Cavity a bCartridge Dimensions Torque
ModelTypical
Code L C K (lb. ft.)
3 c Installation
aLocating 12Capacity
GPM RPCCCartridge
– LAN Cavity
T - 162A 1.22 a 3/4”b 2.11 2.17 2.31 Torque
25/30
Tank Shoulder Model Code L C K (lb. ft.)
2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet 10 GPM PRDB – LAN T - 11A 1.38 7/8” 3.09 3.16 3.34 30/35
a 50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
2 20 GPM PRFB – LAN T - 2A 1.38 1 1/8” 3.47 3.53 3.75 45/50
Inlet 100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1 40 GPM PRHB – LAN T - 17A 1.81 1 1/4” 3.94 4.00 4.19 150/160
1 200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Reduced Pressure 80 GPM PRJB – LAN T - 19A 2.50 1 5/8” 4.88 5.03 5.12 350/375
Performance Curves
RPCC
PRDB PRFB Typical Pressure
PRHBRise PRJB
5000 5000 5000 5000 5000
4000 Regulated Pressure
4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
3000 Relieving Reducing

3000 Relieving 3000
Reducing Relieving 3000 Reducing
2000 3000 3000 4000
2000 2000 2000 2000 2000
1000 1500 1000 3000 1000
P = psi
P = psi
P = psi
1000 1000
P = psi
2000 2000
1000 0 40 80 2000 160 200
120
0 5 10 15 20 25 0 10 20 30 40 50 0 20 40 60 80 100 0 80 160 240 320 400
Flow 500
= GPM Flow1000
= GPM Flow = GPM 1000 Flow = GPM Flow = GPM
1000
0 0 0
-5 -2.5
■
0 Maximum
5 10 15 operating pressure
-40 -20 0 5 10=155000
20 25 psi -60 -30 0 10 20 30 40 50
0
-80 -60 -20 -40 0 20 40 60 80
■
■ Back
Maximum pressure on the pressure
50002)psi is directly additive at a 1:1 ratio to the valve setting.
■
■ Factory pressure
pressure settings establishedatatblocked
setting established 4 GPM control port (deadhead)
■
■ Typical
Maximum response time 10 =ms.
valve leakage PRDB: 2 in3/min./1000 psi: PRFB: 3 in3/min./1000 psi, PRHB:
■ 4 in3/min./1000
Maximum leakagepsi,=PRJB: in3/min./1000
RPCC,5 RPEC: psi
2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■ in 3 /min./1000
Pressure psi,
at port 3 isRPKC: 5 in
directly 3/min./1000
additive to thepsi.
valve setting at a 1:1 ratio and should not exceed 3000 psi .
■
■ RPCC
All springminimum
rangessetting for allofspring
are capable ranges
operating with is 75
5000psipsi inlet pressure.
RP
PR ✱ C
B – ✱ ✱✱
Nominal
Nominal
Capacity Control**
Adjustment Range
Range Seal
Seal
Capacity
C
D 1210 GPM*
GPM $$ 31.90
51.00 LL A
A 100
Standard
Standard Screw
500 -- 3000 psi +$
3000 psi
Screw +$ 0.00
0.00 N +$
+$ 0.00
Buna-N +$ 0.00
0.00
N Buna-N
F
E 2520 GPM
GPM $$ 36.20
73.40 CC B Tamper Resistant
50 - Resistant
1500
B 50 - 1500 psi
Tamper psi +$ 0.00 +$
+$
+$ 0.00 V Viton V 4.10
Viton
4.10 +$ 2.00
H 40 GPM $136.80 K D 20 - 800 psi
Handknob +$ 5.00
G
J 5080 GPM
GPM $$268.60
51.80 K C Handknob
E 150
20 - -400
6000psipsi +$ 2.00 +$ 5.00
I 100 GPM $ 97.30 S 60
N 20 -- 800
200 psi
psi +$ 1.00
W*750 - 4500 psi
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
Available for PRFB and PRHB
W
A 150750--4500
3000psipsi +$ 0.00
B 300 - 1500 psi +$ 0.00 Adjustment Range Options:
D 200 - 800
Adjustment Range +$ 1.00 PRDB Only:
psi Options:
E B,100
A, C, and
- 400Wpsi +$ 1.00
A is standard set at 1000 psi.
N
S Option is standard
50 - 200 psi set
+$ at2.00
400 psi.B, D, E, S are standard set at 200 psi.
Q Option is standard set at 200 psi.PRFB, PRHB:
A, W are standard set at 1000 psi.
D is standard set at 400 psi.
E is standard set at 200 psi.
S is standard set at 100 psi.
** See page 162 for information * Not available for PRFB, PRHB
Visit www.sunhydraulics.com for detailed and complete technical
on Control Options Customerinformation
may specifyon our fullsetting.
pressure line of products.
Reducing and Reducing/Relieving Valves
PILOT OPERATED REDUCING/RELIEVING, EXTERNALLY DRAINED
+ - 4
3
2 1
b
c
4
Drain
3
Tank Locating Typical c Installation
10 GPM PVDA – LAN T - 21A 1.38 7/8” 3.09 3.15 3.34 30/35
a
2 20 GPM PVFA – LAN T - 22A 1.38 1 1/8” 3.44 3.50 3.69 45/50
Inlet
40 GPM PVHA – LAN T - 23A 1.81 1 1/4” 3.93 3.99 4.18 150/160
1 80 GPM PVJA – LAN T - 24A 2.50 1 5/8” 4.78 4.90 5.03 350/375
Reduced Pressure
Performance Curves
PVDA PVFA PVHA PVJA
Regulated Pressure
2000 2000 2000 2000
1500 1500 1500 1500

P = psi
P = psi
P = psi
P = psi
1000 1000 1000 1000
500 500 500 500

0 0 0 0
-10 -5 0 5 10 15 -20 -10 0 10 20 30 -40 -20 0 20 40 60 -80 -140 0 40 80 120

■ Control pilot flow = PVDA: 7 to 10 in3/min., PVFA: 10 to 15 in3/min., PVHA, PVJA:
15 to 20 in3/min.
■ Maximum pressure at port 3 should be limited to 3000 psi.
■ Pressure on the drain (port 4) is directly additive to the valve setting at a 1:1 ratio and should not
exceed 5000 psi.

PV ✱ A – ✱ ✱ ✱
Capacity
F 20 GPM $100.00 C Tamper Resistant +$ 4.10 B 50 -1500 psi +$ 0.00 V Viton
H 40 GPM $181.61 K Handknob +$ 5.00 D 25 - 800 psi
J 80 GPM $344.00 E 25 - 400 psi
W 150 - 4500 psi

All are standard set at 200 psi.
A and B are 3000 psi.
D and E are 2000 psi.
**See page 162 for information W is 5000 psi inlet pressure.
PILOT OPERATED REDUCING/RELIEVING, VENTABLE
+ -
4
3
2 1
b
c
4
Vent
Tank Locating Typical c Installation
10 GPM PVDB – LAN T - 21A 1.38 7/8” 3.09 3.15 3.34 30/35
2
a
Inlet
20 GPM PVFB – LAN T - 22A 1.38 1 1/8” 3.44 3.50 3.69 45/50
40 GPM PVHB – LAN T - 23A 1.81 1 1/4” 3.93 3.99 4.18 150/160
1 80 GPM PVJB – LAN T - 24A 2.50 1 5/8” 4.78 4.90 5.03 350/375
Reduced Pressure
Performance Curves
PVDB PVFB PVHB PVJB
Regulated Pressure
2000 2000 2000 2000
1500 1500 1500 1500

P = psi
P = psi
P = psi
P = psi
1000 1000 1000 1000
500 500 500 500

0 0 0 0
-10 -5 0 5 10 15 -20 -10 0 10 20 30 -40 -20 0 20 40 60 -80 -140 0 40 80 120

■ Control pilot flow = PVDB: 7 to 10 in3/min., PVFB: 10 to 15 in3/min., PVHB, PVJB: 15 to 20 in3/min.
■ By controlling the pressure at the vent (port 4), the effective setting of the valve can be controlled below
the nominal valve setting.

PV ✱ B – ✱ ✱ ✱
Nominal
F 20 GPM $102.80 C Tamper Resistant +$ 4.10 B 50 -1500 psi +$ 0.00 V Viton
H 40 GPM $184.30 K Handknob +$ 5.00 D 25 - 800 psi
J 80 GPM $347.60 E 25 - 400 psi
W 150 - 4500 psi

All are standard set at 200 psi.
A and B are 3000 psi.
D and E are 2000 psi.
** See page 162 for information W is 5000 psi inlet pressure.
AIR CONTROLLED, PILOT OPERATED REDUCING
SAE-4 Pilot Port Air Pilot
3
b
2 1
c
3
Drain Locating
a
2 20 GPM PBFC – ABN T - 2A 1.38 1 1/8” 2.01 - 45/50
Inlet
40 GPM PBHC – BBN T - 17A 1.81 1 1/4” - 2.48 150/160
80 GPM PBJC – BBN T - 19A 2.50 1 5/8” - 3.11 350/375
1
Reduced Pressure
Performance Curves
PBFC PBHC PBJC
Regulated Pressure
2000 2000 2000
1500 1500 1500

P = psi
P = psi
P = psi
1000 1000 1000
500 500 500
0 5 10 15 20 25 30 0 10 20 30 40 50 60 0 20 40 60 80 100 120

■ Control pilot flow = PBFC: 10 to 15 in3/min., PBHC, PBJC: 15 to 20 in3/min.
■ Maximum pressure differential, inlet to outlet = 3000 psi.
■ The pressure at port 3 determines the minimum valve setting and should not exceed 1000 psi.

PB ✱ C – ✱ ✱ ✱
Nominal
Capacity Control Adjustment Range Seal
F 20 GPM $131.10 Available in PBFC only B 50 - 1500 psi +$ 0.00 N Buna-N

Pilot Port at
J 80 GPM $386.80 end of Cartridge
Available for PBHC, PBJC only
B SAE-4
Pilot Port at
end of Cartridge
AIR CONTROLLED, PILOT OPERATED REDUCING/RELIEVING
SAE-4 Pilot Port Air Pilot
b
c 2 1
3
Tank Locating
a
2 20 GPM PPFC – ABN T - 2A 1.38 1 1/8” 2.24 - 45/50
Inlet 40 GPM PPHC – BBN T - 17A 1.81 1 1/4” - 2.48 150/160
80 GPM PPJC – BBN T - 19A 2.50 1 5/8” - 3.11 350/375
1
Reduced Pressure
Performance Curves
PPFC PPHC PPJC
Regulated Pressure
Relieving Reducing Relieving Reducing Relieving Reducing
2000 2000 2000
1500 1500 1500

P = psi
P = psi
P = psi
1000 1000 1000
500 500 500

0 0 0
-20 -10 0 10 20 30 -40 -20 0 20 40 60 -80 -140 0 40 80 120

■ Control pilot flow = PPFC: 10 to 15 in3/min., PPHC, PPJC: 15 to 20 in3/min.
■ Maximum pressure differential, inlet to outlet = 3000 psi.
■ The pressure at port 3 determines the minimum valve setting and should not exceed 1000 psi

PP ✱ C – ✱ ✱ ✱
Capacity
F 20 GPM $143.30 Available in PPFC only B 50 - 1500 psi +$ 0.00 N Buna-N

Pilot Port at
J 80 GPM $412.20 end of Cartridge
Available for PPHC, PPJC only
B SAE-4
Pilot Port at
end of Cartridge
Relief Valves
MODULATING ELEMENT WITH INTEGRAL PILOT CONTROL CAVITY
Full Adjustment 5 Turns 3 into the end of the modulating element via the T-8A cavity. These pilot control
T-8A
+ - Cav cartridges are sold separately and include electro-proportional, solenoid, air
b pilot, and hydraulic pilot operation. See Pilot Control Cartridges on page 121.
2 1
c 2 1
3 c
Drain Locating
b Shoulder
Locating Cartridge Dimensions

2 a Shoulder
Typical Cartridge Dimensions Installation
Inlet Capacity TypicalCartridge Cavity a b c c TorqueInstallation
Capacity Model Code Cavity
Cartridge a b (lb. ft.) Torque
10 GPM ModelPBDB
Code – 8WN T - 11A 1.38 7/8L 1.19C K 30/35 (lb. ft.)
1 a
Reduced 20 GPM RPCCPBFB
12 GPM – LAN– 8WN T - 162AT - 2A1.22 1.383/4” 2.11
1 1/8 2.17
1.38 2.3145/50 25/30
2 Pressure 25 GPM RPEC – LAN T - 10A T - 17A
1.56
Outlet 40 GPM PBHB – 8WN 1.817/8” 2.00
1 1/4 2.06
1.81 2.25
150/160 30/35
80 GPM RPGCPBJB
50 GPM – LAN– 8WN
T - 3A T - 19A
1.88 1 1/8”
2.50 2.12
1 5/8 2.18
2.31 2.38
350/375 45/50
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
Performance Curves
PBDB-8 PBFB-8 PBHB-8 PBJB-8
Regulated Pressure with T-8A Pilot Stage Installed
Relieving Reducing Relieving Typical
Reducing Pressure Rise
Relieving Reducing Relieving Reducing
2000 2000 2000 2000
5000 5000 5000 5000 5000
1500 1500 1500 1500
P = psi
P = psi
P = psi
4000 4000 4000 P = psi 4000

P = psi
4000
P = psi
P = psi
P = psi
P = psi
3000 1000 3000 1000 3000 1000 3000 1000 3000

2000 2000 2000 2000 2000
500 500 500 500
1000 0 1000 0 1000 0 1000 0 1000
-15 -10 -05 0 5 10 15 -30 -20 -10 0 10 20 30 -20 -40 -60 0 20 40 60 -120 -80 -40 0 40 80 120
Flow
25 = GPM 0 Flow = GPM 160 200Flow = GPM
0 5 10 15 20 10 20 30 40 Flow
50 = GPM0 20 40 60 80 100 0 40 80 120 0 80 160 240 320 400
■
Maximum operating pressure
pressure = = 5000
5000 psi
psi
Control pilotmaximum
flow = PBDB-8: 3 3
pressure7attoPort
10 in2. /min., PBFB-8: 10 to 15 in /min., PBHB-8, PBJB-8:
■
■ Will accept
15 to 20 in3/min.
■ Maximum inlet pressure is determined by the bias spring. The D spring is limited to 2000 psi
■ Typical
maximum response time 10
differential ms. and the W spring is limited to 5000 psi maximum inlet pressure.
pressure
■ Maximum
With leakage = RPCC,
the -8 control option, theRPEC: in 3/min./1000
2stage psi,first
RPGC: 3 in3/min./1000 psi, RPIC:
torque4value.
3main valve should be installed to the correct
■
in 3/min./1000 psi, RPKC: 5 in /min./1000 psi.
The T-8A pilot control valve should then be installed into the main stage valve to its required
■ RPCC
torque minimum
value. setting for all spring ranges is 75 psi
RP
PB ✱ C
B – ✱
8 ✱✱
Nominal
Nominal Base Control Minimum Control
Seal
C
D 1210 GPM*
GPM $
$ 31.90
47.20 L
8 Standard Screw
T-8A Cavity in +$
+$ 0.00
0.00 A
D 100 - 3000 psi +$
25 psi +$ 0.00
1.00 N Buna-N +$ 0.00
N Buna-N
E 25 GPM $ 36.20 hex bodyResistant
C Tamper for +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
separately)
K
J 200 GPM
80 GPM $187.00 Q 60 - 400 psi +$ 1.00
W 150 - 4500 psi +$ 0.00

for detailed and complete technical information on our full line of products.
Reducing
Relief and Reducing/Relieving Valves
Valves
3-WAY, OPERATED,
PILOT MODULATING ELEMENT PISTON
BALANCED WITH INTEGRAL PILOT CONTROL CAVITY
Full Adjustment 5 Turns The -8 control option allows a pilot control valve to be incorporated directly
T-8A
3
+ - Cav into the end of the modulating element via the T-8A cavity. These pilot control
22 11
cc
3
b
Tank Locating
Shoulder
Locating
Shoulder
2 a TypicalTypical c Installation
Installation
Inlet Capacity
Capacity Cartridge Cavity Cavity a
Cartridge a b b c TorqueTorque
Model Code
Model Code L C K (lb. ft.) (lb. ft.)
a 12 10
GPMGPM RPCCPPDB
– LAN– 8WNT - 162AT - 11A1.22 1.383/4” 7/82.11 1.19
2.17 2.31 30/35 25/30
1
2 Reduced 25 20
GPMGPM PPFB
RPEC – 8WNT - 10A T - 2A 1.56
– LAN 1.387/8” 1 1/8
2.00 1.38
2.06 2.25 45/50 30/35
Outlet Pressure
50 40
GPMGPM PPHB
RPGC – 8WNT - 3A T - 17A1.88
– LAN 1.81
1 1/8” 1 1/4
2.12 1.81
2.18 2.38150/160 45/50
10080 GPM
GPM RPICPPJB – 8WNT - 16A T - 19A2.44
– LAN 2.50
1 1/4” 1 5/8
2.44 2.31
2.47 2.69350/375150/160
Inlet 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
RPCC PPDB-8 RPEC PPFB-8 RPGC PPHB-8 RPIC PPJB-8 RPKC
Regulated Pressure
Typicalwith T-8A Pilot
Pressure RiseStage Installed
Relieving Reducing
5000 Relieving 5000Reducing
5000 2000 2000 2000 2000
4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
1500 1500 1500 1500

P = psi
P = psi
P = psi
P = psi
3000 3000 3000 3000 3000

2000 1000 2000 1000 2000 1000 2000 1000 2000
1000 1000 1000 1000 1000
500 500 500 500
0 5 10 015 20 25 0 10 20 0
30 40 50 0 20 40 0
60 80 100 0 40 80 1200 160 200 0 80 160 240 320 400
-15 -10
Flow = GPM
-05 0 5 10 15
Flow = GPM -30 -20 -10 0 10 20 30Flow = GPM-20 -40 -60 0 20 40 Flow
60 = GPM-120 -80 -40 0 40 80 120
Flow = GPM
■ Maximum operating pressure = 5000 psi.
■ Will accept maximum pressure at Port 2.3
■ Control pilot flow = PPDB-8: 7 to 10 in /min., PPFB-8: 10 to 15 in3/min., PPHB-8, PPJB-8: 15 to
■ Back
20 in3pressure
/min. on the tank port (port 2) is directly additive at a 1:1 ratio to the valve setting.
■
■ Factory
Pressurepressure
at port 3settings established
is directly additive at
to 4the
GPM
valve setting at a 1:1 ratio and should not exceed 3000 psi.
■
Maximum inlet pressure is determined by the bias spring. The D spring is limited to 2000 psi
Maximum leakage = RPCC, RPEC: 2 inW 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■
maximum differential pressure and the spring is limited to 5000 psi maximum inlet pressure.
■ RPCC
The T-8Aminimum setting
pilot control for all
valve spring
should ranges
then is 75 psi
be installed into the main stage valve to its required torque value.
RP
PP ✱ C
B – ✱
8 ✱✱
C
D 1210 GPM*
GPM $
$ 31.90
56.00 L
8 Standard Screw
T-8A Cavity in +$
+$ 0.00
0.00 A
D 100 - 3000 psi +$
25 psi +$ 0.00
1.00 N Buna-N +$ 0.00
N Buna-N
E 25 GPM $ 36.20 hex body for
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
separately)
J
K 80 GPM
200 GPM $187.00 Q 60 - 400 psi +$ 1.00
W 150 - 4500 psi +$ 0.00

Visit
www.sunhydraulics.com for
for detailed
detailed and
and complete
complete technical
information on
on our
our full
full line
line of
of products.
products.
38
3-WAY, EXTERNALLY DRAINED, MODULATING ELEMENT WITH INTEGRAL
3 The -8 control option allows a pilot control valve to be incorporated directly
4 into the end of the modulating element via the T-8A cavity. These pilot control
b T-8A
Cav cartridges are sold separately and include electro-proportional, solenoid, air
4 c 2 1
Outlet
3
Tank Locating
Shoulder
2 a Typical Installation
Intlet Capacity Cartridge Cavity a b c Torque
10 GPM PVDA – 8WN T - 21A 1.38 7/8 1.78 30/35
1
Reduced 20 GPM PVFA – 8WN T - 22A 1.38 1 1/8 2.00 45/50
Pressure 40 GPM PVHA – 8WN T - 23A 1.81 1 1/4 2.59 150/160
80 GPM PVJA – 8WN T - 24A 2.50 1 5/8 3.16 350/375
Performance Curves
PVDA-8 PVFA-8 PVHA-8 PVJA-8
Regulated Pressure with T-8A Pilot Stage Installed
2000 2000 2000 2000
1500 1500 1500 1500

P = psi
P = psi
P = psi
P = psi
1000 1000 1000 1000
500 500 500 500

0 0 0 0
-15 -10 -05 0 5 10 15 -30 -20 -10 0 10 20 30 -20 -40 -60 0 20 40 60 -120 -80 -40 0 40 80 120

■ Control pilot flow = PVDA-8: 7 to 10 in3/min., PVFA-8: 10 to 15 in3/min., PVHA-8, PVJA-8:
15 to 20 in3/min.
■ Pressure on the drain (port 4) is directly additive to the valve setting at a 1:1 ratio and should not exceed
5000 psi.
■ Maximum inlet pressure is determined by the bias spring. The D spring is limited to 2000 psi
maximum differential pressure and the W spring is limited to 5000 psi maximum inlet pressure.

PV ✱ A – 8 ✱ ✱
Nominal Base Control Minimum Control
Seal
D 10 GPM $ 75.20 8 T-8A Cavity in +$ 0.00 D 25 psi +$ 1.00 N Buna-N
hex body for
F 20 GPM $105.00 pilot operation W 100 psi +$ 0.00 V Viton
(Pilot valve to
separately)
J 80 GPM
ELECTRO-PROPORTIONAL, DIRECT ACTING REDUCING/RELIEVING
1
d
2 3
b
c
3
Typical e Installation
Locating Capacity Cartridge Cavity a b c d Torque
Drain Shoulder Model Code (dia.) (lb. ft.)
2 a 5 GPM PRDL - MDN T-11A 1.38 7/8” 1.50 2.76 1.47 30/35
Intlet
Reduced 1
Pressure
Performance Curves
PRDL
Regulated Pressure Command vs.
Secondary Pressure
Relieving Reducing
400 300
P = psi
300
P = psi
200
200
100
100
0
-6 -4 -2 0 2 4 6 0 20 40 60 80 100
Flow = GPM Command (%)

■ Maximum valve leakage = 20 in³/min. at deadhead.
Dither should be adjustable between 100 - 250 Hz.

PR D L – M D N
Nominal Control** Operating Range Seal
Capacity
L 5 GPM $125.00 M Manual Override +$ 0.00 D 50 - 500 psi +$ 0.00 N Buna-N
(Standard)
E 25 - 250 psi +$ 0.00 V Viton
NOTE: Coil must be
ordered separately. Use S 10 - 100 psi
12V DC or 24V DC
only. See page 167.
Relief Valves
ELECTRO-PROPORTIONAL,
+ - DIRECT ACTING WITH LOW LEAKAGE
1
2 1
e
c
b
dLocating
Shoulder 2 3
b Model Code L C K (lb. ft.)
c a 12 GPM RPCC – LAN
3
Typical T - 162A 1.22 3/4” 2.11 2.17
e
2.31 Installation
25/30
2
Drain
Locating Capacity
25 GPM Cartridge
RPEC –Model
LAN CodeT - 10A
Cavity1.56 a 7/8” b c
2.00 d Torque
2.06 (dia.) 2.25 (lb. ft.)
30/35
Shoulder
Outlet
2 a 50 GPM
5 GPM RPGCPRDP
– LAN
- MDNT - 3A T-11A 1.88 1.381 1/8”7/8” 2.12
1.50 2.18 1.47 2.38
2.76 45/50
30/35
Intlet 100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
Reduced 1 200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Pressure
Performance Curves
5000 5000 5000 PRDP 5000 5000
4000 4000 4000 4000
P = psi
4000
Regulated Pressure Command3000
vs.
P = psi
P = psi
P = psi
P = psi
3000 3000 3000 3000

2000 2000 2000
Secondary Pressure
2000 2000
Relieving Reducing
400 300
1000 1000 1000 1000 1000
P = psi
300
P = psi
0 5 10 15 20 25 0 10 20 30 40 50 0 20 40 200 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400

Flow = GPM Flow
200= GPM Flow = GPM Flow = GPM Flow = GPM
100
100
0
pressure = 5000 psi
■ -6 -4
Will accept maximum -2 0 2
pressure
Flow = GPM
4
at6Port 2. 0 20 Command
40 60 80 100
(%)
■ Factory
Maximum pressure
operating settings established
pressure = 5000atpsi4 GPM
■ Typical
Maximum response time 10 =ms.
valve leakage 2 in³/min. at deadhead.
■ Pressure atleakage
Maximum port 3 is=directly
RPCC, additive 3/min./1000
RPEC: 2tointhe valve setting
psi, at 3 in3/min./1000
a 1:1 ratio
RPGC: and should psi,
not RPIC:
exceed43000 psi.
■ RPCC
Dither minimum
should be setting
adjustablefor between
all spring100
ranges is Hz.
- 250 75 psi
RP DC
PR ✱ P – M D✱
✱ ✱ N
Nominal
Capacity Control** Adjustment Range
Operating Range Seal
C
P 12 GPM*
5 GPM $ 31.90
$120.00 L
M Standard Screw +$ 0.00
Manual Override A
D 100
50 - -500
3000
psipsi +$ 0.00 N Buna-N +$ 0.00
(Standard)
E 25 - 250 psi +$ 0.00 V Viton
G 50 GPM $ 51.80 K Coil must be +$ 5.00
Handknob
NOTE: C 150 - 6000 psi +$ 2.00
ordered separately. Use
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
12V DC or 24V DC
K 200 GPM $187.00 (Series 770-***) coils Q 60 - 400 psi +$ 1.00
only. See page 167.
W 150 - 4500 psi +$ 0.00

NOTES

Pilot Operated Check
Cartridge Valves
Cartridge Type Page

2 Ext.
3 2 3
Pilot Operated 44
1 1
3
Atmospherically Referenced,
3 Port Cavity 45
1
3
Vented, 4 Port Cavity 46
4

Relief Valves Check Valves
Pilot Operated
PILOT
PILOT OPERATED,
OPERATED BALANCED PISTON
Full Adjustment 5 Turns 2 Ext.
+
+ --
3 2 3
L Control
X Control 2 1
c
bb c 1 1
Locating X, L Controls B, E, P Controls
Shoulder
Pilot Locating TypicalTypical cc Installation
Installation
Shoulder Capacity Cartridge
Cartridge CavityCavity a b Torque
Capacity
Model Model
Code Code
a b LX,B,E,P C L K Torque
lb. (lb.
ft. ft.)
a 12 7.5
GPM GPM RPCCCKBB– LAN– XCNT - 162A
T - 163A1.22 1.22 3/4” 3/4” 2.11 1.25 2.17 1.76 2.31 25/3025/30
22 a 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet 15 GPM CKCB – XCN T - 11A 1.38 7/8” 1.19 2.50 30/35
Valve 50 GPM
30 GPM RPGC – LAN
CKEB – XCN T - 3AT - 2A 1.88 1.38 1 1/8”1 1/8” 2.12 1.38 2.18 2.81 2.38 45/5045/50
Inlet 11
100 60
GPMGPM RPIC CKGB
– LAN– XCNT - 16AT - 17A 2.44 1.81 1 1/4”1 1/4” 2.44 1.81 2.47 3.28 2.69 150/160
150/160
Load
200120
GPMGPM RPKCCKIB
– LAN– XCNT - 18A
T - 19A 3.13 2.50 1 5/8”1 5/8” 2.81 2.31 2.94 3.94 3.06 350/375
350/375
Performance
Performance Curves
Curves
RPCC
CKB* RPEC
CKC* RPGC
CKE* RPIC
CKG* RPKC
CKI*
Typical
Typical Pressure
Pressure Rise
Drop
5000 5000 5000
480 5000
480 5000
480
480 480
400 400
4000 400
4000 400
4000 400
4000
psi
4000
psi
psi
psi
psi
PP == psi
PP==psi
PP==psi
psi
PP==psi
300 300
3000 300
3000 300
3000 300
3000
3000
==
210 210 210 210 210

PP
2000 2000 2000 2000 2000

OT OT
140 XEN 140 OT 140 OT 140 PIL 140 XEN
OT XEN
PIL
XEN PIL XEN LL PIL
1000 PIL 1000 LL 1000 LL 1000 FU 1000 LL
70 LL 70 FU 70 FU 70 70 XCN FU
FU XCN XCN XCN
XCN
0 40 80 120 160 200
00 52.5 10 5 15 7.520 25
10 0
0
10
5
20
10
30
15
40 50
20
0
0 20
7.5 40 15 60 22.5
80 100
30 0 20 40 60 80 00 80
40 16080 240 120320 160
400
Flow Flow == GPM
GPM Flow
Flow =
= GPM Flow == GPM
GPM Flow==GPM
GPM
Flow == GPM
GPM Flow GPM Flow Flow
■ Maximum valve leakage = 1 drop/min.
■ CKBB, CKBD available only with 30 psi or 75 psi check valve cracking pressures.
■ CK*D has sealed pilot for use in circuits where cross port leakage is undesirable.
■ CK*B has unsealed pilot to allow air trapped in the pilot line to be purged from the circuit.
CK ✱RP C – ✱✱✱ ✱ ✱
✱✱–
Nominal Nominal
Capacity Version Control** Adjustment Range Cracking Pressure
Control** Seal Seal
Capacity
B* 7.5 GPM $C 24.60 $ 31.90
B Bleed
12 GPM* L Standard
through Pilot Screw X +$
+$ 0.00 0.00PilotA 100 -+$
Standard 30000.00
psi +$
A 40.00
psi N 2.00 +$ 0.00
+$Buna-N N Buna-N
C 15 GPM $E 25.70 $ 36.20
25 GPMD Sealed C Tamper
Pilot Piston Resistant
+$ 1.00 L +$ 4.10
Manual LoadB 50 - 1500 psi
+$ 6.00 +$
B 0.00
15 psi V+$Viton
1.00 +$ 2.00
V Viton
G 50 GPM $ 51.80 K Handknob Release
+$ 5.00 C 150 - 6000 psi +$ 2.00
E 30 GPM $ 37.50 C 30 psi
I 100 GPM $ 97.30 B +$ psi
N 60 - 800
1/4" BSPP External 0.00 +$ 1.00
G 60 GPM $ 66.40 Pilot Port 3 blocked D 50 psi
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
I 120 GPM $ 130.50 E SAE-4 External +$ 4.00 E 75 psi
W 150 - 4500 psi
Pilot Port 3 blocked +$ 0.00
F 100 psi
P 1/4" NPTF External
Pilot Port 3 blocked
** See page 162 for information * Minimum setting 75*psi on allCKBD
CKBB, ranges.available
on Control Options ** See page 162Customer may specify with
for information pressure E Cracking +$ 1.10
C andsetting.
on Control Options Pressures Only.

Visit www.sunhydraulics.com and complete
for detailed technical
and complete information
technical on ouronfull
information ourline
fullofline
products.
of products.
6
Pilot Operated Check Valves
ATMOSPHERICALLY REFERENCED, 3 PORT CAVITY
Atmospheric Reference 2
L Control
X Control 3
b c
1
3
Pilot Locating Cartridge Dimensions
Shoulder
Model Code X L S (lb. ft.)
a
2 15 GPM CKCV – XCN T - 11A 1.38 7/8” 1.99 2.24 1.68 30/35
Valve
30 GPM CKEV – XCN T - 2A 1.38 1 1/8” 2.31 2.56 2.0 45/50
60 GPM CKGV – XCN T - 17A 1.81 1 1/4” 2.78 3.02 2.47 150/160
Inlet 1
120 GPM CKIV – XCN T - 19A 2.50 1 5/8” 3.30 3.77 - 350/375
Performance Curves
CKCV CKEV CKGV CKIV
Typical Pressure Drop
400 400 400 400
300 300 300 300

P = psi
P = psi
P = psi
200 200 200 P = psi 200

T T O T
100 XEN ILO 100 XEN OT 100 XEN P ILO 100 XEN PIL
LP PIL LL LL
UL LL FU FU
XCN F XCN FU XCN XCN
0 5 10 15 20 0 7.5 15 22.5 30 0 20 40 60 80 0 40 80 120 160


■ Approximately 1 drop of fluid will pass from the pilot area to the vented spring chamber every
4000 cycles.

CK ✱ V – ✱ ✱ ✱
Nominal Control** Cracking Pressure Seal
Capacity
C 15 GPM $ 44.60 X Standard Pilot +$ 0.00 A 4 psi +$ 2.00 N Buna-N
E 30 GPM $ 63.90 S External SAE-4 +$ 5.00 B 15 psi +$ 1.00 V Viton

Vent Port
G 60 GPM $107.30 C 30 psi
L Manual Load
I 120 GPM $186.50 Release External D 50 psi
Vent
E 75 psi
F 100 psi

on Control Options
Relief Valves
Pilot Operated Check Valves
VENTED, + - 4 PORT CAVITY
Full Adjustment 5 Turns 2

+ - 2 1
L Control 3
X Control c
bb
4
Locating
c Shoulder 1 Cartridge Dimensions
4
Vent Capacity Cartridge Cavity a b Torque
3 a Cartridge Dimensions
Pilot Locating 12 GPM RPCC Typical
– LAN T - 162A 1.22 3/4” 2.11 c 2.17 Installation 25/30
2.31
2 Shoulder
25Capacity
GPM RPECCartridge
– LAN Cavity
T - 10A 1.56 a 7/8”b 2.00
X 2.06
L
Torque
2.25 30/35
Outlet Model Code (lb. ft.)
5015
GPM
GPM RPGC – LAN
CVCV – XCN
T - 3A
T - 21A 1.881.38 1 1/8”
7/8” 2.12
2.11 2.18
2.34 2.38
30/35 45/50
2
a 10030GPM RPIC – LAN T - T16A 2.441.38 1 11/4” 2.44 2.47 2.69 150/160
GPM CVEV – XCN - 22A 1/8” 2.34 2.56 45/50
ValveInlet 1
20060GPM
GPM RPKC – LAN
CVGV – XCN
T - T18A
- 23A 3.131.81 1 15/8”
1/4” 2.81
2.81 2.94
3.03 3.06
150/160 350/375
Performance Curves 120 GPM CVIV – XCN T - 24A 2.50 1 5/8” 3.50 3.77 350/375
Load 1
5000 CVCV 5000 CVEV 5000 CVGV 5000
CVIV 5000
4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
3000 3000 Typical

3000 Pressure Drop 3000 3000
2000 2000 2000 2000 2000
400 400 400 400
1000 1000 1000 1000 1000
300 300 300 300
P = psi
P = psi
P = psi
P = psi
0 5 10 20015 20 25 0 10 20 200
30 40 50 0 20 40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
200 200
T T OT
100 XEN ILO 100 XEN OT 100 XEN P ILO 100 XEN PIL
LP PIL LL LL
UL LL FU FU
XCN ■ Maximum operating pressure = 5000 psi
F XCN FU XCN XCN
0 5 10
15 20 0 7.5 15 22.5 30 0 20 40 60 80 0 40 80 120 160
Flow =Will
■
GPM accept maximum Flow pressure
= GPM at Port 2. Flow = GPM Flow = GPM
■
■ Back pressure
50002)psiis directly additive at a 1:1 ratio to the valve setting.
■
■ Factory
Maximum valve leakage = 1 drop/min. 4 GPM
pressure settings established at
■
■
Typical response
Port 4 (vent) time
should 10 ms.
never be blocked as seal weepage will eventually cause valve to malfunction.
Will accept pressure at port 4RPEC:
leakage = RPCC, 2 incannot
■
■ (vent) but exceed 5000 psi.
RP
CV ✱ C
V – ✱ ✱✱
Nominal
Nominal
Capacity Control**
Adjustment Range
Range Seal
Seal
Capacity
C
C 1215 GPM*
GPM $
$ 31.90
41.80 L
X Standard
Standard Screw
Pilot +$
+$ 0.00
0.00 A
A 100
4 psi- 3000 psi +$
+$ 0.00
2.00 N Buna-N +$ 0.00
N Buna-N
E 30 GPM $ 62.80 L Manual Load +$ 6.00 B 15 psi +$ 1.00 V Viton
Release +$ 5.00 C 150 - 6000 psi +$ 2.00
IG 60 GPM
100 GPM $105.50
$ 97.30 C
N 30 -psi
60 800 psi +$ 1.00
K
I 200
120 GPM
GPM $187.00
$185.00 Q
D 60
50 -psi
400 psi +$ 1.00
W
E 150 - 4500 psi
75 psi +$ 0.00
F 100 psi Range Options:

Adjustment

on Control Options
Counterbalance Cartridge Valves
Cartridge Type Page
2 1
Standard, 4000 psi Maximum Setting 48
3
2 1
Standard, 5000 psi Maximum Setting 49
3
2 1
Semi-Restrictive, 4000 psi Maximum Setting 50
3
2 1
Semi-Restrictive, 5000 psi Maximum Setting 51
3
2 1
Restrictive, 4000 psi Maximum Setting 52
3
2 1
Restrictive, 5000 psi Maximum Setting 53
3
2 1
Without Pilot Assist, 3 Port Cavity 54
3
2 1
Atmospherically Referenced, 3 Port Cavity 55
3
4
1
2 Vented, 4000 psi Maximum Setting 56
3
4
1
2 Vented, 6000 psi Maximum Setting 57
3

Counterbalance Valves
Relief Valves
STANDARD, 4000 PSI MAXIMUM SETTING
Turn
Fullscrew clockwise
Adjustment to reduce
5 Turns
setting and release load.
+
Complete Adjustment - 3 3/4 Turns
- + 2 1
2 1
c
3
b c
b
Locating
3 Cartridge Dimensionsc
Pilot Locating Typical Installation
Capacity TypicalCartridge Cavity a b c Installation
Torque
Shoulder
Capacity Cartridge
ft.)
a 15 GPM CBCA – LHN T - 11A 1.38 7/8” 1.97 2.19 30/35
a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 30 GPM CBEA – LHN T - 2A 1.38 1 1/8” 2.38 2.50 45/50
2
Valve 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet 60 GPM CBGA – LHN T - 17A 1.81 1 1/4” 2.75 3.31 150/160
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
120 GPM CBIA – LHN T - 19A 2.50 1 5/8” 3.50 4.09 350/375
Load 1 100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
Performance Curves
CBC* CBE* CBG* CBI*
Free Flow and Pilot Open Pressure Drop
400 400
Typical Pressure
400
Rise 400
5000 300 5000 300 5000 300 5000 300 5000

P = psi
P = psi
P = psi
P = psi
4000 Piloted Open 4000 4000 Piloted4000

Open
p
P = psi
4000
P = psi
P = psi
200 200 200 200
P = psi
P = psi
Piloted Open
p
3000 3000 3000 p3000
Piloted Open 3000
100 100 100 100 Free Flow
2000 2000 2000 Free Flow 2000 2000
0 Free Flow Free Flow
0 0 1000 0
1000 0 5 1000
10 15 0 10 1000
20 30 0 20 40 60 0 40 1000 80 120
0 5 10 15 20 Q
25 = GPM 0 10 20 30 40 Q
50 = GPM 0 20 40 60 80 100Q = GPM 0 40 80 120 160 200 Q = GPM0 80 160 240 320 400
■ Load holding to 3000 psi with 4000 psi valve setting
■ Maximum valve leakage at reseat = 5 drops/min.
■ Reseat exceeds 85% of set pressure
■ Factory pressure setting established at 2 in³/min.
■ Counterbalance valves should be set at least 1.3 times the maximum load induced pressure.
■ Back pressure at port 2 adds to the effective relief setting at a ratio of 1 plus the pilot ratio times the
■ Maximum
back leakage = RPCC, RPEC: 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
pressure.
CB ✱RP C – ✱✱✱ ✱ ✱
✱✱–
Nominal Nominal
Control** Seal Seal
Capacity
C 15 GPM $C 42.90 $ Pilot
A 3:1
12 GPM* 31.90Ratio L Standard Screw L +$
+$ 0.00 0.00Screw
Standard A 100 -+$
30000.00
psi +$ 0.00 N Buna-N
25 psi Check Spring +$ 0.00
N Buna-N
E 30 GPM $E 58.80
25 GPMB $ 36.20
1.5:1 C Tamper
Pilot Ratio +$ 2.00 C +$
Resistant 4.10
Tamper B 50 - 1500
Resistant psi
+$ 4.10 +$
H 0.00- 4000
1000 V psi
Viton +$ 2.00
+$ 0.00 V Viton
G 50 GPM (with sealed
$ 51.80 pilot)
K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
G 60 GPM $ 108.70 I 400 - 1500 psi
I Y
100 GPM $ Pilot
2:1 97.30
Ratio N 60 - 800 psi +$ 1.00
I 120 GPM $ 225.00 (with Bleed through
K 200 GPM $187.00
Pilot) Q 60 - 400 psi +$ 1.00
4 psi Check Spring
W 150 - 4500 psi A 1000

+$ 0.00- 4000 psi
B 400 - 1500 psi
Q Option is standard set at
A 200
and Hpsi.are standard set at 3000 psi.
** See page 162*for
** See page 162 for information information
Minimum setting 75 psiIon
and
allBranges.
on Control Options on Control Options
Customer may specify Customer
pressuremay +$ 1.10
specify setting.
setting.
Visit www.sunhydraulics.com for detailed and complete 48
technical information on our full line of products.
Counterbalance
Relief Valves Valves
STANDARD,
PILOT 5000 PSI
OPERATED, MAXIMUMPISTON
BALANCED SETTING
Turn
Fullscrew clockwise
Adjustment to reduce
5 Turns
+
Complete Adjustment - 3 3/4 Turns
- + 2 1
2 1
c
3
bb c
Locating
3 Cartridge Dimensionsc
Pilot Locating Typical Installation
Capacity Typical
Cartridge Cavity a b c Installation
Torque
Shoulder
Capacity Cartridge
ft.)
a 15 GPM CBCG – LJN T - 11A 1.38 7/8” 1.97 2.19 30/35
a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 30 GPM CBEG – LJN T - 2A 1.38 1 1/8” 2.38 2.50 45/50
2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Valve
Outlet 60 GPM CBGG – LJN T - 17A 1.81 1 1/4” 2.75 3.31 150/160
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
120 GPM CBIG – LJN T - 19A 2.50 1 5/8” 3.50 4.09 350/375
Load 1 100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
Performance Curves
CBC* CBE* CBG* CBI*
400 400
Typical Pressure
400
Rise 400
5000 300 5000 300 5000 300 5000 300 5000
P = psi
P = psi
P = psi
P = psi
4000 4000 4000 Piloted4000

Open
p
P = psi
4000 Piloted Open

P = psi
P = psi
P = psi
P = psi
200 Piloted Open

p 200 200 200
3000 3000 3000 3000 3000
Piloted Open
p
100 100 100 2000 100 Free Flow
2000 2000 2000Free Flow 2000
0 Free Flow Free Flow
1000 1000 0 1000 0 1000 0 1000
0 5 10 15 0 10 20 30 0 20 40 60 0 40 80 120
0 5 10 15 20 Q
25 = GPM 0 10 20 30 40 Q
50 = GPM 0 20 40 60 80 100Q = GPM 0 40 80 120 160 200Q = GPM0 80 160 240 320 400
■
■ Load holding
Maximum to 3850pressure
operating psi with=5000 5000psi
psivalve setting
Will accept maximum pressure at Portdrops/min.
Maximum valve leakage at reseat = 5
■
■ 2.
■
■ Reseatpressure
Back exceedson 85%the of
tanksetport
pressure
(port 2) is directly additive at a 1:1 ratio to the valve setting.
■
■
Factory pressure
Factory pressure settings
setting established
establishedatat24in³/min.
GPM
Typical response time 10 ms. be set at least 1.3 times the maximum load induced pressure.
Counterbalance valves should
■
■
■
■ Back pressure
Maximum at port
leakage 2 adds to
= RPCC, the effective
RPEC: relief setting
2 in 3/min./1000 at a ratio
psi, RPGC: of3/min./1000
3 in 1 plus the pilot ratio times
psi, RPIC: 4
the
3 back pressure. 3
CB ✱RP
✱ ✱ –C –✱✱✱ ✱ ✱
Nominal Nominal
Control** Seal Seal
Capacity
C 15 GPM $ C44.60 $ 31.90
G 4.5:1
12 GPM* L Standard
Pilot Ratio Screw L +$
+$ 0.00 0.00Screw
Standard A 100 -+$
30000.00
psi +$ 25
0.00 N Buna-N
psi Check Spring +$ 0.00
N Buna-N
E 30 GPM $ E 60.60 $ 36.20

25 GPMH 10:1 Pilot RatioC Tamper C +$
Resistant
+$ 0.00 4.10
Tamper B 50 - 1500
Resistant psi
+$ 4.10 +$ 0.00- 5000
J 2000 V psi
Viton +$ 2.00
+$ 0.00 V Viton
G 60 GPM $ 110.60 L 2.3:1 Pilot Ratio +$ 2.70 K 1000 - 2500 psi
I $ 97.30
100 GPM (with sealed pilot) N 60 - 800 psi +$ 1.00
I 120 GPM
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
4 psi Check Spring
W 150 - 4500 psi C 2000

+$ 0.00- 5000 psi
D 1000 - 2500 psi
Adjustment
Q Option is standard set Range Options:
at 200 psi.
J and C are standard set at 3000 psi.
** See page 162 for information * Minimum setting
** See page 162 for information 75 psi on all ranges.
K and D are standard set at 2000 psi.
on Control Options on Control Options
Customer may specify pressuremay
Customer setting. +$ 1.10
specify setting.
SEMI-RESTRICTIVE,
Relief Valves 4000 PSI MAXIMUM SETTING
PILOT OPERATED,
Turn screw clockwise to reduce
BALANCED PISTON
Complete Adjustment 3 3/4 Turns
-
+
+
- 2 1
2 1
b 3
c c
b
3 Locating Typical c Installation
Pilot Shoulder
Locating Capacity Cartridge Cavity a b Torque
Shoulder Model Code Cartridge L
Dimensions C (lb. ft.)
10 GPM
Capacity CBBC – LHN CavityT - 11A a
Cartridge 1.38 b 7/8” 1.97 2.19 30/35
Torque
a ModelCBDC
Code – LHN L C K (lb. ft.)
2 20 GPM T - 2A 1.38 1 1/8” 2.38 2.50 45/50
Valve
a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
40 GPM CBFC – LHN T - 17A 1.81 1 1/4” 2.75 3.31 150/160
2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
Load 1 50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1Curves
Performance 200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
CBB* CBD* CBF*
Performance Curves
RPCC RPEC
400
RPGC
400
RPIC
400
RPKC
300 Typical
300 Pressure Rise 300
P = psi P = psi
P = psi P = psi
P = psiP = psi
200 200 200

5000 5000
5000 5000Piloted Open 5000 Piloted Open Piloted Open
100
4000 100
4000 4000
100 4000
P = psi
4000
P = psi
Free Flow Free Flow 3000 Free Flow
3000 3000
0 3000
0 0 3000
0 5 10 15 0 10 20 30 2000 0 20 60 2000
2000 2000 2000
1000 1000
Q = GPM 1000
Q = GPM 1000 Q = GPM 1000
0 5 10 15 20 25 0 10 20 30 40 50 0 20 40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400

Flow = GPM
■ Load holding
Flow to 3000 psi with 4000 Flow
= GPM psi valve
= GPM setting Flow = GPM Flow = GPM
■
■ Maximum valve leakage at reseat
Maximum operating pressure = 5000 psi = 5 drops/min.
■
■ Reseat
Will exceeds
accept 85% ofpressure
maximum set pressure
at Port 2.
Back pressure on the tank port (port at
Factory pressure setting established 2)2isin³/min.
■
■ directly additive at a 1:1 ratio to the valve setting.
Factory pressure settings established at
Counterbalance valves should be set at least 1.3 times the maximum load induced pressure.
■
■ 4 GPM
■
■ Back pressure at port 2 adds
Typical response time 10 ms. to the effective relief setting at a ratio of 1 plus the pilot ratio times the
back pressure.
CB ✱RP
✱ ✱ –C –✱✱✱ ✱ ✱
Nominal Nominal
Control** Seal Seal
Capacity
B 10 GPM $ C42.90
12 GPM*
B $ 31.90
1.5:1 Pilot RatioL Standard ScrewL
+$ 1.90 +$ 0.00Screw
Standard A 100 -+$
30000.00
psi +$ 25
0.00 N Buna-N
N Buna-N
E 25 GPM (with sealed
$ 36.20 pilot)
D 20 GPM $ 63.00 C Tamper Resistant +$ 4.10 H 1000 - 4000 psi +$ 0.00 V Viton
G 50 GPMC $ 51.80
3:1 Pilot Ratio K Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
F 40 GPM $ 110.80 (with sealed pilot) I 400 - 1500 psi
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
4 psi Check Spring
W 150 - 4500 psi +$ 0.00- 4000 psi
A 1000
B 400 - 1500 psi
A, B, C, and W are standard set atRange
Adjustment 1000 psi.
Options:
N Option is standard set atA and
400 H are standard set at 3000 psi.
psi.
** See page 162QforOption
information I and
is standard set at 200Bpsi.
on Control Options
** See page 162 for information * Minimum setting 75Customer may specify setting.
psi on all ranges.
SEMI-RESTRICTIVE,
Relief Valves 5000 PSI MAXIMUM SETTING
PILOT OPERATED,
BALANCED PISTON
- + 2 1
+ -
2 1
b 3
c c
b
3
Pilot Locating
Locating Typical c Installation
Shoulder
Model Code Cartridge L
Dimensions C (lb. ft.)
10 GPM
Capacity CBBD – LJN CavityT - 11A a 1.38 b 7/8”
Cartridge 1.97 2.19 30/35
Torque
2 a ModelCBDD
Code – LJN L C K (lb. ft.)
20 GPM T - 2A 1.38 1 1/8” 2.38 2.50 45/50
Valve a 12 GPM RPCCCBFD
– LAN– LJNT - 162A
40 GPM T - 17A 1.22 1.81 3/4” 1 1/4” 2.11 2.75 2.17 3.31 2.31 25/30
150/160
2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
Load 1 50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1Curves
Performance
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
CBB* CBD* CBF*
Performance Curves
RPCC RPEC
400
RPGC
400
RPIC
400
RPKC
300
300 300
P = psi P = psi
P = psi
P = psi P = psi
200 200 200

5000 5000Piloted Open 5000 Piloted Open 5000 Piloted Open 5000
100
4000 100
4000 100
4000 4000
P = psi
4000
P = psi
P = psi
Free Flow Free Flow Free Flow

3000 0
3000 0
3000 0
3000 3000
0 5 10 15 0 10 20 30 0 20 60
2000 2000 2000 2000 2000
Q = GPM Q = GPM Q = GPM
1000 1000 1000 1000 1000
0 5 10 15 20 ■ 25 0 10 20 30 40 50 0 20 0
40 80
60 160 240
80 100320 0 40 80 120 160 200 400
Flow = GPM Load holding
Flow to 3850 psi with 5000 Flow
= GPM psi valve
= GPM setting Flow = GPM Flow = GPM
■
■ Maximum
Maximum valve leakage
operating at reseat
pressure = 5 psi
= 5000 drops/min.
■
Will accept maximum pressure at Port 2.
■
■ Factory pressure
Back pressure onsetting
the tankestablished
port (port at
2)2isin³/min.
directly additive at a 1:1 ratio to the valve setting.
■
■ Counterbalance
Factory pressure settings established at
valves should be set at least
4 GPM1.3 times the maximum load induced pressure.
■
■ Back pressure at port 2 adds
Typical response time 10 ms. to the effective relief setting at a ratio of 1 plus the pilot ratio times the
back pressure.
CB ✱RP
✱ ✱ –C –✱✱✱ ✱ ✱
Nominal Nominal
Capacity Version Control** Adjustment RangeCracking Pressure
Control** Seal Seal
Capacity
B 10 GPM $ C44.60 $ 31.90
D 4.5:1
12 GPM* Pilot RatioL Standard
+$ 0.00
ScrewL +$ 0.00Screw
Standard A 100 -+$ 0.00
3000 psi +$ 25
0.00 N Buna-N
N Buna-N
(with sealed pilot)
D 20 GPM E 25
$ 63.00 GPM $ 36.20 C Tamper Resistant
C +$ 4.10
Tamper B 50 - +$
Resistant 15004.10
psi J+$ 2000
0.00- 5000
V psi
Viton +$ 2.00
+$ 0.00 V Viton
G 50 GPML 2.3:1 Pilot RatioK Handknob
$ 51.80 +$ 5.00 C 150 - 6000 psi +$ 2.00
F 40 GPM $ 112.60 (with sealed pilot) K 1000 - 2500 psi
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
4 psi Check Spring
W 150 - 4500 psi C

+$ 2000
0.00- 5000 psi
D 1000 - 2500 psi
Adjustment
A, B, C, and W are standard set atRange Options:
1000 psi.
N Option is standard set Jatand
400Cpsi.
** See page 162 Q
forOption
information
is standard set K
at and
200 D are standard set at 2000 psi.
psi.
on Control Options
** See page 162 for information * Minimum setting 75Customer may specify setting.
psi on all ranges.
RESTRICTIVE, 4000 PSI MAXIMUM SETTING
- + 2 1
3
b c
3
Pilot Locating Typical c Installation
Shoulder
5 GPM CBBA – LHN T - 11A 1.38 7/8” 1.97 2.19 30/35
2 a 8 GPM CBDA – LHN T - 2A 1.38 1 1/8” 2.38 2.50 45/50
Valve
15 GPM CBFA – LHN T - 17A 1.81 1 1/4” 2.74 3.31 150/160
20 GPM CBHA – LHN T - 19A 2.50 1 5/8” 3.50 4.09 350/375
Load 1
Performance Curves
CBB* CBD* CBF* CBH*
400 400 400 400
300 Piloted Open 300 Piloted Open 300 Piloted Open 300 Piloted Open
P = psi
P = psi
P = psi
P = psi
200 200 200 200
100 100 100 100

Free Flow Free Flow Free Flow Free Flow
0 0 0 0
0 5 15 0 10 20 30 0 20 40 60 0 40 120
Q = GPM Q = GPM Q = GPM Q = GPM
■ Restrictive valves have no relief capacity other than as a thermal relief.

back pressure.

CB ✱ ✱ – ✱✱✱
Nominal
Version Control** Cracking Pressure Seal
Capacity
B 5 GPM $ 42.90 A 3:1 Pilot Ratio +$ 0.00 L Standard Screw +$ 0.00 25 psi Check Spring N Buna-N
(with sealed pilot)
D 8 GPM $ 63.00 C Tamper Resistant +$ 4.10 H 1000 - 4000 psi +$ 0.00 V Viton
F 15 GPM $ 108.70 Available in CBBY only I 400 - 1500 psi
H 20 GPM $ 225.00 Y 2:1 Pilot Ratio

(with Bleed through 4 psi Check Spring
Pilot)
A 1000 - 4000 psi
B 400 - 1500 psi

A and H are standard set at 3000 psi.
** See page 162 for information I and B are standard set at 1000 psi.
on Control Options Customer may specify setting.
RESTRICTIVE, 5000 PSI MAXIMUM SETTING
- + 2 1
3
b c
3
Pilot Locating Typical c Installation
Shoulder
5 GPM CBBG – LJN T - 11A 1.38 7/8” 1.97 2.19 30/35
2 a 8 GPM CBDG – LJN T - 2A 1.38 1 1/8” 2.38 2.50 45/50
Valve
15 GPM CBFG – LJN T - 17A 1.81 1 1/4” 2.75 3.31 150/160
20 GPM CBHG – LJN T - 19A 2.50 1 5/8” 3.50 4.09 350/375
Load 1
Performance Curves
CBB* CBD* CBF* CBH*
400 400 400 400
300 Piloted Open 300 Piloted Open 300 Piloted Open 300 Piloted Open
P = psi
P = psi
P = psi
P = psi
200 200 200 200
100 100 100 100

0 0 0 0
0 5 15 0 10 20 30 0 20 40 60 0 40 120
■ Restrictive valves have no relief capacity other than as a thermal relief.

back pressure.

CB ✱ ✱ – ✱✱✱
Nominal
Capacity
B 5 GPM $ 44.60 G 4.5:1 Pilot Ratio +$ 0.00 L Standard Screw +$ 0.00 25 psi Check Spring N Buna-N
(with sealed pilot)
D 8 GPM $ 63.00 C Tamper Resistant +$ 4.10 J 2000 - 5000 psi +$ 0.00 V Viton
F 15 GPM $ 110.60 K 1000 - 2500 psi
H 20 GPM
4 psi Check Spring
C 2000 - 5000 psi
D 1000 - 2500 psi

J and C are standard set at 3000 psi.
** See page 162 for information K and D are standard set at 2000 psi.
WITHOUT PILOT ASSIST, 3 PORT CAVITY
Complete Adjustment 3-3/4 Turns
- +
2 1
b
c 3
Locating Typical c Installation
15 GPM CCCA – LAN T - 11A 1.38 7/8” 1.97 2.19 30/35
2 a
Valve 30 GPM CCEA – LAN T - 2A 1.38 1 1/8” 2.38 2.50 45/50
60 GPM CCGA – LAN T - 17A 1.81 1 1/4” 2.74 3.31 150/160
Load
120 GPM CCIA – LAN T - 19A 2.50 1 5/8” 3.52 4.09 350/375
1
Performance Curves
CCCA CCEA CCGA CCIA
Typical Relief Characteristics
5000 5000 5000 5000
4000 4000 4000 4000
P = psi
P = psi
P = psi
P = psi
3000 3000 3000 3000

2000 2000 2000 2000
1000 1000 1000 1000
0 0 0 0
0 5 10 15 0 10 20 30 0 20 40 80 0 40 80 120

■ Back pressure at port 2 is directly additive to the relief setting of the valve.

CC ✱ A – ✱✱✱
Nominal Version Control** Cracking Pressure Seal
Capacity
C 15 GPM $ 46.20 A Standard +$ 0.00 L Standard Screw +$ 0.00 25 psi Check Spring N Buna-N
E 30 GPM $ 63.60 C Tamper Resistant +$ 4.10 H 1000 - 4000 psi +$ 0.00 V Viton
G 60 GPM $ 113.70 I 400 - 1500 psi
I 120 GPM
4 psi Check Spring
A 1000 - 4000 psi
B 400 - 1500 psi

A and H are standard set at 3000 psi.
** See page 162 for information I and B are standard set at 1000 psi.
ATMOSPHERICALLY REFERENCED, 3 PORT CAVITY
Complete Adjustment 4 Turns
- + 2 1
c
b
3
Atm.
Reference
3 Typical c Installation
Pilot Locating Capacity Cartridge Cavity a b Torque
Shoulder Model Code L C (lb. ft.)
15 GPM CACA – LHN T - 11A 1.38 7/8” 2.91 3.16 30/35
2 a 30 GPM CAEA – LHN T - 2A 1.38 1 1/8” 3.29 3.54 45/50
Valve
60 GPM. CAGA – LHN T - 17A 1.81 1 1/4” 3.75 3.97 150/160
120 GPM CAIA – LHN T - 19A 2.50 1 5/8” 4.58 4.96 350/375
Load 1
Performance Curves
CAC* CAE* CAG* CAI*
300 300 300 300
P = psi
P = psi
P = psi
P = psi
200 200 200 200

100 100 100 100
Piloted Open Piloted Open Piloted Open Piloted Open

0 0 0 0
0 5 10 15 0 10 20 30 0 20 40 60 0 40 80 120
■ Load holding to 3000 psi with 4000 psi valve setting for CA*A, CA*K; 4600 psi with 6000 psi valve
setting for CA*G, CA*L.
■ Free flow check cracking pressure = 40 psi

CA ✱ ✱ – ✱✱✱
Nominal
Capacity Version Control** Cracking Pressure Seal
C 15 GPM $ 62.80 A 3:1 Pilot Ratio +$ 0.00 L Standard Screw +$ 0.00 A and K Pilot Ratios N Buna-N
E 30 GPM $ 96.60 G 5:1 Pilot Ratio +$ 1.80 C Tamper Resistant +$ 4.10 H 1000 - 4000 psi +$ 0.00 V Viton
G 60 GPM $ 151.90 K 1:1 Pilot Ratio +$ 1.80 I 400 - 1500 psi
I 120 GPM $ 290.60 L 2:1 Pilot Ratio

G and L Pilot Ratios
F 1000 - 2500 psi
G 2000 - 6000 psi

H is standard set at 3000 psi.
I is standard set at 1000 psi.
F is standard set at 2000 psi.
** See page 162 for information G is standard set at 4000 psi.
Relief Valves
Counterbalance
PILOT OPERATED, Valves BALANCED PISTON
VENTED, 4000 PSI MAXIMUM SETTING
Turn screw+clockwise
- to reduce
4
- +
22 1 1
c
b
b 3
Locating
c Shoulder
4 Typical Cartridge Dimensionsc Installation
Vent Capacity Cartridge Cavity a b
L C
Torque
K
Model CodeTypical c Installation
(lb. ft.)
3 aLocating Capacity Cartridge Cavity a b Torque
Pilot 12 GPM RPCC –Model
LAN CodeT - 162A 1.22 3/4” 2.11 L 2.17 C 2.31 (lb. 25/30
ft.)
2 Shoulder
15 GPM RPEC CWCA–
25 GPM – LAN LHN T - 10AT - 21A 1.56 1.38 7/8” 7/8” 2.00 2.91 2.06 3.16 2.25 30/35
30/35
Outlet
2 a 30 GPM RPGC CWEA–
50 GPM – LAN LHN
T - 3A T - 22A 1.88 1.381 1/8”1 1/8” 2.12 3.29 2.18 3.54 2.38 45/50
45/50
Valve 60 GPM RPIC CWGA–
100 GPM – LAN LHN
T - 16AT - 23A 2.44 1.811 1/4”1 1/4” 2.44 3.75 2.47 3.97 2.69 150/160
150/160
Inlet 1
200 120
GPM GPM RPKC CWIA
– LAN– LHN
T - 18AT - 24A 3.13 2.501 5/8”1 5/8” 2.81 4.58 2.94 4.78 3.06 350/375
350/375
Load 1
Performance Curves
RPCC
CWC* CWE* CWG*
Typical Pressure Rise CWI*
5000 5000 Free Flow and Pilot Open Pressure Drop
5000 5000 5000
4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
300 300 300 300
P = psi
P = psi
3000 3000 3000 3000 P = psi 3000

P = psi
P = psi
P = psi
2000 200 2000 200 2000 200 2000 200 2000

Free Flow Free Flow Free Flow 1000 Free Flow
1000 1000 1000 1000
100 100 100 100
0 5 10 15 20 25 0 10 20 30 40 50 0 20 40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
Piloted Open
Flow = 0GPM
Piloted Open
Flow = GPM
0
Piloted Open
Flow = GPM0
Piloted Open
Flow = GPM 0 Flow = GPM
0 5 10 15 0 10 20 30 0 20 40 60 0 40 80 120
■Q = GPM
Maximum Q = GPM= 5000 psi
operating pressure Q = GPM Q = GPM
■ Free
in flow check
3/min./1000 psi,cracking
RPKC: pressure = 40 psipsi.
5 in3/min./1000
RPCC minimum setting for all springatranges
Counterbalance valves should be set least 1.3 times
psi the maximum load induced pressure.
■
■ is 75
CW ✱RP C – ✱✱✱ ✱
✱✱– ✱✱
Nominal
Nominal Capacity Control** Adjustment Range Seal
Capacity
C 15 GPM $ 60.90 A 3:1 Pilot Ratio +$ 0.00 L Standard Screw +$ 0.00 Pilot Ratios N Buna-N
E 30 GPM $ 86.20 K 1:1 Pilot Ratio +$ 2.00 C Tamper Resistant +$ 4.10 H 1000 - 4000 psi +$ 0.00 V Viton
G 60 GPM $ 147.80 I 400 - 1500 psi
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
I 120 GPM
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
W 150 - 4500 psi +$ 0.00

on Control Options Customer may specify Adjustment setting.Options:+$ 1.10
pressure Range
H is standard set at 3000 psi.
** See page 162 for information I is standard set at 1000 psi.
6
Relief Valves
VENTED, 6000 PSI MAXIMUM SETTING
Turn screw+ clockwise
- to reduce
4
- +
22 1 1
c
b
b 3
c Locating
Shoulder
4 Typical Cartridge Dimensionsc Installation
Vent Capacity CartridgeTypical Cavity a b Torque
L Cc K Installation
3 Capacity Model Code
Cartridge Cavity a b (lb. ft.)
Torque
Pilot aLocating L C
Shoulder
12 GPM RPCC –Model
LAN CodeT - 162A 1.22 3/4” 2.11 2.17 2.31 (lb.25/30
ft.)
2 15 GPM RPEC CWCG–
25 GPM – LAN LFN T - 10AT - 21A1.56 1.387/8” 7/8” 2.00 2.91 2.06 3.16 2.25 30/35
30/35
Outlet
2 a 30 GPM RPGC CWEG–
50 GPM – LAN LFN T - 3A T - 22A1.88 1.381 1/8” 1 1/8”2.12 3.29 2.18 3.54 2.38 45/50
45/50
Valve 60 GPM RPIC CWGG–
100 GPM – LAN LFN T - 16AT - 23A2.44 1.811 1/4” 1 1/4”2.44 3.75 2.47 3.97 2.69 150/160
150/160
Inlet 1 120
200 GPM GPM CWIG
RPKC – LAN – LFN
T - 18AT - 24A3.13 2.501 5/8” 1 5/8”2.81 4.58 2.94 4.78 3.06 350/375
350/375
Load 1
Performance Curves
Performance Curves
CWC* CWE* CWG* CWI*
5000 5000 Free Flow5000
and Pilot Open Pressure Drop
5000 5000
300 4000 300 4000 300 4000 300 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
3000 3000 3000 3000 3000
P = psi
P = psi
P = psi
P = psi
200 200 200 200

2000 2000 2000 2000 2000
1000 1000 1000 1000 1000
100 100 100 100
0 5 10 15 20 25 0 Open
Piloted 10 20 30 40 50 0
Piloted 20
Open 40 60 80 100 0Piloted Open
40 80 120 160 200 0 Piloted
80Open160 240 320 400
0 0 0 0
Flow = GPM
0 5 10 Flow
15 = GPM
0 10 20 Flow
30 = GPM0 20 40
Flow
60
= GPM 0 40 80 Flow
120 = GPM
■Q = GPM Q = GPM Q = GPM Q = GPM

Maximum operating pressure = 5000 psi
■
■ Will
Loadaccept maximum
holding to 4600 pressure at Port
psi with 6000 psi2.valve setting
■
■ Back pressure
Maximum on leakage
valve the tankatport (port
reseat = 2) is directly additive at a 1:1 ratio to the valve setting.
5 drops/min.
■
■ Factory pressure85%
Reseat exceeds settings established
of set pressure at 4 GPM
■
■ Typical
Factoryresponse
pressure time 10established
setting ms. at 2 in³/min.
■
■ Maximum
Free flow leakage
check = RPCC,
cracking RPEC:=240
pressure in 3psi
/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
RP
CW ✱ ✱✱ C
– – ✱✱✱ ✱
✱✱
Nominal Nominal
Control** Seal Seal
Capacity
C 15 GPM $C 62.90 $ Pilot
G 5:1
12 GPM* 31.90RatioL Standard Screw L +$
+$ 0.00 0.00 Screw
Standard A 100 - +$
30000.00
psi +$ 0.00Pilot
N Ratios
Buna-N +$ 0.00
N Buna-N
E 30 GPM $E 88.00 $ Pilot

25 GPML 2:1 36.20RatioC Tamper ResistantC +$
+$ 2.00 4.10Resistant
Tamper B 50 - 1500
+$ psi
4.10 +$
F 0.00- 2500
1000 V psi
Viton +$ 2.00
+$ 2.00 V Viton
G 60 GPM $ 149.60 G 2000 - 6000 psi
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
I 120 GPM
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
W 150 - 4500 psi +$ 0.00

on Control Options Customer may specify Adjustment Range Options:
pressure setting. +$ 1.10
F is standard set at 2000 psi.
** See page 162 for information G is standard set at 4000 psi.
Visit www.sunhydraulics.com for detailed and complete 6technical information on our full line of products.
NOTES

Check Cartridge Valves
Cartridge Type Page

2
Free Flow Nose to Side 60

1
Free Flow Side to Nose 61

1
Free Flow Side to Nose, Port 3 Blocked 62

1
Free Flow Nose to Side with Bypass Orifice 63

1
2
3
2 To 1 Free Flow, with Customer Specified
Orifice, Port 3 Blocked, 3 Port Cavity 64
1

Relief Valves
Free Flow
+ Check
- Valves
FREE FLOW NOSE TO SIDE
2 2 1
c
b
b
c Locating
Shoulder
Shoulder
1
a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 a 25 GPM RPEC – LAN T - 10A 1.56 7/8”Cartridge Dimensions
2.00 2.06 2.25 30/35
Outlet
2 50 GPM RPGC – LAN
Capacity Cartridge -
T 3A 1.88
Cavity 1 1/8”
a 2.12b 2.18 2.38 Torque45/50
Out
Model Code X lb.150/160
ft.
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69
Inlet 1
RPKC –CXBA
LAN – XCN
10 GPM
200 GPM T - 18A T - 162A
3.13 1.22
1 5/8” 3/4”
2.81 2.94.82 3.06 25/30
350/375
20 GPM CXDA – XCN T - 13A 1.38 7/8” .75 30/35
Performance
In 1 Curves 40 GPM CXFA – XCN T - 5A 1.62 1 1/8” .69 45/50
RPCC RPEC 80 GPM RPGC
CXHA – XCN T - 16A RPIC
2.44 1 1/4” RPKC
.97 150/160
160 GPM Typical
CXJA – XCNPressure TRise
- 18A 3.13 1 5/8” 1.19 350/375
5000 5000 5000 5000 5000
Performance Curves 4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
CXBA 3000
CXDA 3000
CXFA 3000
CXHA
2000
3000
CXJA
3000
2000 2000 2000 2000
1000 1000 Typical
2000 5 10 15 20 25 200 0 10 20 30 40 50 200 0 20 40 60 80 100 200 0 40 80 120 160 200 200 0 80 160 240 320 400
150 150 150 150 150
P = psi
P = psi
P = psi
P = psi
P = psi
100 XEN
■ Maximum
100 operating pressure100= 5000 psi
XEN 100 XEN 100 XEN XEN
50 XCN
XAN
■ Will50 accept maximum pressure
N 50 at Port 2. 50 XCN
XAN
50 XCN
XAN
XCN
XAN
XAN
0 2.5 5 7.5
■
10 Back0 pressure10on the 15 tank
20 port 0(port102) is20 directly
30 additive0 at a25 1:1 50ratio75to the
40 100 valve0setting. 100 150 200
Flow = GPM
Flow = GPM ■ Factory pressure settings establishedFlow
Flow = GPM
at 4= GPM
GPM Flow = GPM
■
■ Typical
Maximum response timepressure
operating 10 ms. = 5000 psi
■
■ Maximum
Maximum leakage
valve = RPCC,
leakage = 1 RPEC:
drop/min. 2 in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■ Will accept 5000 psi at ports 1 and 2.
RP
CX ✱ C
A – ✱ ✱✱
Nominal
Capacity Control** Adjustment
Cracking Range
Pressure Seal
C
B 1210 GPM*
GPM $ 31.90
14.80 L
X Standard Screw
Non-adjustable +$ 0.00 A 100
4 psi- 3000 psi +$ 0.00 N Buna-N +$ 0.00
E
D 25
20 GPM $ 36.20
16.90 C Tamper Resistant +$ 4.10 B 50
15 -psi
1500 psi +$ 0.00
1.00 V Viton +$ 2.00
G
F 50
30 GPM $ 51.80
24.30 K Handknob +$ 5.00 C 150 - 6000 psi
30 psi +$ 2.00
IH 100 GPM
80 GPM $ 97.30
46.40 N
D 60
50 -psi
800 psi +$ 1.00
K
J 200
160 GPM $187.00
$ 83.20 Q
E 60
75 -psi
400 psi +$ 1.00
F 150
W 100 -psi
4500 psi +$ 0.00

** See page 162 for information 6 US Shortcut Catalogue #999-901-243
on Control Options
Relief Valves
Free
FullFlow Check
Adjustment 5 Turns Valves
+ -
FREE FLOW SIDE TO NOSE
2 2 1
c
b b
c
Locating
Locating
Shoulder
a 12 GPM RPCC – LAN T - 162A 1.22 3/4”Cartridge
2.11 2.17 2.31 25/30
a Dimensions
2 25 GPM RPEC – LANTypical T - 10A 1.56 7/8” 2.00 2.06 c 2.25 Installation
30/35
2 Outlet Capacity Cartridge Cavity a b Torque
In 50 GPM RPGC – LAN
Model CodeT - 3A 1.88 1 1/8” 2.12 2.18 X 2.38 45/50
lb. ft.
7.5 GPM RPIC –CXAD
100 GPM LAN – XCN T - 16A 2.44
T - 162A 1 1/4”
1.22 2.44
3/4” 2.47.82 2.69 150/160
25/30
Inlet 1
15 GPM RPKC –CXCD
200 GPM LAN – XCN
T - 18A 3.13
T - 13A 1 5/8”
1.38 2.81
7/8” 2.94.75 3.06 350/375
30/35
Out 1
Performance Curves 30 GPM CXED – XCN T - 5A 1.62 1 1/8” .69 45/50
60 GPM CXGD – XCN T - 16A 2.44 1 1/4” .97 150/160
120 GPM CXID – XCN T - 18A 3.13 1 5/8” 1.19 350/375
Performance Curves 5000 5000 5000 5000
5000
CXAD CXCD 4000

CXED 4000
CXGD
4000
CXID
4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
3000 3000 3000 3000 3000

2000 2000 Typical
1000 1000 1000 1000 1000
200 300 300 300 300
20 0 10 20 30 40 50 0 20 40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
1500 5 10 15 25
Flow = GPM
P = psi

P = psi
P = psi
Flow = GPM
P = psi
Flow = GPM
P = psi
200 200 200 200

100 XEN
XEN XEN XEN XEN
50 XCN
■ Maximum
100 operating pressure100= 5000 psi
XCN
100 100
XCN
XCN
XAN XAN XAN XAN XAN
0 2.5 5 7.5
■
10
Will 0accept
5
maximum
10 15
pressure
20 0
at Port 2.
15 22.5 30 0 40 60 80 0 120 160
Flow = GPM ■ Back pressureFlow =onGPMthe tank port (portFlow 2) is= GPM
directly additive at aFlow
1:1=ratio Flow = GPM
GPM to the valve setting.
■ Maximum valve leakage = 1 drop/min. 3
■ Maximum leakage = RPCC, RPEC: 2 in /min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■ Will accept 5000
in3/min./1000 psi,psi at ports
RPKC: 5 in13and 2.
/min./1000 psi.
■
■ CXAD only available
RPCC minimum with
setting for4,all30spring
and 75 psi cracking
ranges is 75 psipressures.
RP ✱ D
CX C – ✱ ✱✱
Nominal
Nominal
Capacity Control**
Cracking Range
Pressure Seal
Seal
Capacity
C 12 GPM*
A* 7.5 GPM $$ 31.90
16.90 L Non-adjustable
X Standard Screw +$+$ 0.00
0.00 A
A 4100
psi- 3000 psi +$
+$ 0.00
2.00 N
N Buna-N +$ 0.00
Buna-N
E
C 25 GPM
15 GPM $$ 36.20
17.90 C Tamper Resistant +$ 4.10 B
B 50 psi
15 - 1500 psi +$
+$ 0.00
1.00 V
V Viton
Viton +$ 2.00
G
E 50 GPM
30 GPM $$ 51.80
24.30 K Handknob +$ 5.00 C
C 150psi
30 - 6000 psi +$ 2.00
I
G 100GPM
60 GPM $$ 97.30
46.40 N
D 60 psi
50 - 800 psi +$ 1.00
K
I 200 GPM
120 GPM $$187.00
83.20 Q 75
E 60 psi
- 400 psi +$ 1.00
W 100
F 150 psi
- 4500 psi +$ 0.00

* CXAD available with

** See page 162 for information A, C, E Cracking Pressures
on Control Options
Visit www.sunhydraulics.com Only. information on our full line of products.
for detailed and complete technical
Free Flow Check Valves
FREE FLOW SIDE TO NOSE, PORT 3 BLOCKED
2
b 3
1
Locating
Shoulder
a Capacity Cartridge Cavity a b
X
Torque
2 Model Code lb. ft.
Inlet 15 GPM CXCE – XCN T - 11A 1.38 7/8” 1.19 30/35
30 GPM CXEE – XCN T - 2A 1.38 1 1/8” 1.38 45/50
60 GPM CXGE – XCN T - 17A 1.81 1 1/4” 1.81 150/160
Outlet 1
120 GPM CXIE – XCN T - 19A 2.50 1 5/8” 2.31 350/375
Performance Curves
CXCE CXEE CXGE CXIE
300 300 300 300
P = psi
P = psi
P = psi
P = psi
200 200 200 200
100 XEN 100 XEN 100 100 XEN

XEN
XCN
XAN XAN XCN XAN XCN XAN
0 5 10 15 20 0 15 22.5 30 0 20 40 60 80 0 40 80 120 160



CX ✱ E – ✱ ✱ ✱
Capacity
C 15 GPM $ 23.00 X Non-adjustable +$ 0.00 A 4 psi +$ 2.00 N Buna-N
E 30 GPM $ 32.90 B 15 psi +$ 1.00 V Viton
G 60 GPM $ 57.20 C 30 psi
I 120 GPM $100.40 D 50 psi
E 75 psi
F 100 psi

on Control Options
FREE FLOW NOSE TO SIDE WITH BYPASS ORIFICE
2
b
c
Locating
Shoulder
1
Port Model Code X lb. ft.
7.5 GPM CNBC – XCN T - 162A 1.22 3/4” .82 25/30
1 Port 15 GPM CNDC – XCN T - 13A 1.38 7/8” .75 30/35
30 GPM CNFC – XCN T - 5A 1.63 1 1/8” .69 45/50
60 GPM CNHC – XCN T - 16A 2.43 1 1/4” .97 150/160
120 GPM CNJC – XCN T - 18A 3.13 1 5/8” 1.19 350/375
Performance Curves
CNBC CNDC CNFC CNHC CNJC
200 200 200 200 200
150 150 150 150 150

P = psi
P = psi
P = psi
P = psi
P = psi
100 XEN 100 XEN 100 XEN 100 XEN 100 XEN
50 XCN 50 N 50 XCN 50 XCN 50 XCN

XAN XAN XAN XAN
XAN
0 2.5 5 7.5 10 0 10 15 20 0 10 20 30 40 0 25 50 75 100 0 100 150 200


■ Orifice range = CNBC, CNDC: .015 - .062 in., CNFC: .015 - .078 in., CNHC: .015 - .094 in.,
CNJC: .015 - .125 in.

CN ✱ C – ✱ ✱ ✱
Capacity
B 7.5 GPM $ 20.00 X Non-adjustable +$ 0.00 A 4 psi +$ 1.00 N Buna-N
D 15 GPM $ 20.00 B 15 psi +$ 1.00 V Viton
F 30 GPM $ 28.30 C 30 psi
H 60 GPM $ 48.20 D 50 psi
J 120 GPM $ 90.10 E 75 psi
F 100 psi
Customer specified orifice setting range:

CNBC: .015 - .062 in.
CNDC: .015 - .062 in.
CNFC: .015 - .078 in.
**See page 162 for information CNHC: .015 - .094 in.
on Control Options CNJC: .015 - .125 in.
2 TO 1 FREE FLOW, WITH CUSTOMER SPECIFIED ORIFICE, PORT 3
BLOCKED, 3 PORT CAVITY
2
3
c
1
Locating
Shoulder
2 Model Code X lb. ft.
Outlet 15 GPM CNCD – XCN T - 11A 1.38 7/8” 1.19 30/35
30 GPM CNED – XCN T - 2A 1.38 1 1/8” 1.38 45/50
Inlet 1 60 GPM CNGD – XCN T - 17A 1.81 1 1/4” 1.81 150/160
120 GPM CNID – XCN T - 19A 2.50 1 5/8” 2.31 350/375
Performance Curves
CNCD CNED CNGD CNID
300 300 300 300
P = psi
P = psi
P = psi
P = psi
200 200 200 200
100 XEN 100 XEN 100 100 XEN

XEN
XCN
XAN XAN XCN XAN XCN XAN
0 5 10 15 20 0 15 22.5 30 0 20 40 60 80 0 40 80 120 160


■ Will accept 5000 psi at ports 1 and 2
■ Orifice range = CNCD: .015 - .062 in., CNED: .015 - .078 in., CNGD: .015 - .094 in.,
CNID: .015 - .125 in.

CN ✱ D – ✱ ✱ ✱
Nominal
Control** Cracking Pressure Seal
Capacity
C 15 GPM $ 25.10 X Non-adjustable +$ 0.00 A 4 psi +$ 1.00 N Buna-N
E 30 GPM $ 34.00 B 15 psi +$ 1.00 V Viton
G 60 GPM $ 59.20 C 30 psi
I 120 GPM $102.50 D 50 psi
E 75 psi
F 100 psi
Customer specified orifice setting range:

CNCD: .015 - .062 in.
CNED: .015 - .078 in.
** See page 162 for information CNGD: .015 - .094 in.
on Control Options CNID: .015 - .125 in.
Flow Control Valves
Cartridge Type Page
Fully Adjustable Needle 66

1
Fully Adjustable Needle, High Capacity 67

1
Fully Adjustable Needle with 68

Reverse Flow Check
1
Fixed Orifice, Pressure Compensated 69

1
Fixed Orifice, Pressure Compensated

with Reverse Flow Check 70
1
Fully Adjustable Pressure Compensated with

Reverse Flow Check 71
1
Free Flow Side-to-Nose with Bypass Orifice 72

1
Electro-proportional, Normally Closed Throttle 73

1
Electro-proportional, Normally Open Throttle 74

1

Relief Valves
+ -
Flow Control Valves
FULLY ADJUSTABLE 2 NEEDLE1
c
b - +
Locating
Shoulder
c Typical c Installation
b Capacity Cartridge Cavity a b Torque
1 Model Code L C K (lb. ft.)
a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 Locating 25 GPM RPEC – LAN T - 10A
7/8” 2.00 1.562.06 2.25 30/35
Outlet Shoulder Cartridge Dimensions
50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
Maximum Typical c Installation
100Nominal
GPM RPIC –Cartridge
LAN T - 16A
Cavity 2.44 a 1 1/4” b 2.44 2.47 2.69 150/160
Torque
Inlet 1 Orifice Model Code L H K lb. ft.
a 200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
.16" dia. NFBC – LCN T - 162A 1.22 3/4” 1.59 - 1.73 25/30
2
Performance Curves .19" dia. NFCC – LCN T - 13A 1.38 7/8” 2.27 2.49 2.50 30/35
Port
RPCC RPEC .25" dia. RPGC
NFDC – LAN T - 5A RPIC 1 1/8”
1.62 2.35 RPKC
2.82 2.73 45/50
Port 1 .38" dia. NFECTypical

– LENPressure
T - 16A
Rise 2.44 1 1/4” 2.66 3.06 2.91 150/160
5000 5000
.56" dia. NFFC5000
– LGN T - 18A 3.13
5000 1 5/8” 3.31 3.50 5000 3.47 350/375
4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
Performance Curves
P = psi
P = psi
3000 3000 3000 3000 3000
NFBC NFCC NFDC NFEC NFFC

2000 2000 2000 2000 2000
1000 1000 1000 1000 1000
0 5 10 15 20 25 0 10 20 30 Adjustment
40 50 Sensitivity
0 20 40at 100
60 psi Differential
80 100 0 40 80 120 160 200 0 80 160 240 320 400
8 8 20 40 80
Flow = GPM
Flow = GPM
Flow = GPM
Flow = GPM
Flow = GPM
6 ■ Maximum
LGN
4
LCN
■ Will4 accept maximum pressure 10
at Port 2.
LCN
20 40
LAN LEN
2 2 5 LDN
10 20 LFN
LBN
LHN
0 1 2
Number of Turns
3 4 ■ 5
Factory
0
pressure
1 2 3
settings
4 5
established
0 1
at2 4 GPM
3 4 5 0 1 2 3 4 5 0 1 2 3 4 5
Number of Turns Number of Turns Number of Turns Number of Turns
■
■ Maximum
Maximum leakage
operating= pressure
RPCC, RPEC:
= 50002psi in 3/min./1000 psi, RPGC: 3 in3/min./1000 psi, RPIC: 4
■ Maximum valve leakage at shutoff = less than 5 drops/min.
RP
NF ✱ C – ✱ ✱ ✱
Nominal
Maximum
Nominal Base Control** Orifice Options Seal
C Orifice
12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
B .16" dia. $ 19.90 L Standard Screw +$ 0.00 NFBC N Buna-N
C .16"
C
G .19"GPM
50 dia. 19.90
$ 51.80 H Handknob
K Calibrated 8.00
+$ 5.00 C 150 - 6000 psi +$ 2.00 V Viton
Handknob with NFCC
ID 100
.25" GPM
dia. $
$ 97.30
27.30 Detent Lock N
C 60
.19"- 800 psi +$ 1.00
K 200 GPM $187.00 D
Q .09"
60 - 400 psi +$ 1.00
E .38" dia. $ 53.30 K Handknob +$ 5.00
W 150 - 4500 psi +$ 0.00
NFDC
F .56" dia. $ 95.40 A .25"
B .13"
A, B, C, andNFEC
W are standard set at 1000 psi.
N
E Option
.38" is standard set at 400 psi.
Q
F Option
.28" is standard set at 200 psi.
NFFC +$ 1.10
G .56"
H .38"

on Control Options
Flow Control Valves
FULLY ADJUSTABLE NEEDLE, HIGH CAPACITY
2
c
b
1
Locating
Shoulder
Nominal Typical c Installation
Cartridge Cavity a b Torque
2 a Orifice Model Code L H K (lb. ft.)
Port
.33" dia. NFCD – LFN T - 13A 1.38 7/8” 2.27 2.49 2.50 30/35
.50" dia. NFDD – LGN T - 5A 1.62 1 1/8” 2.35 2.82 2.73 45/50
.69" dia. NFED – LHN T - 16A 2.44 1 1/4” 2.66 3.06 2.91 150/160
1
Port
.85" dia. NFFD – LIN T - 18A 3.13 1 5/8” 3.31 3.50 3.47 350/375
Performance Curves
NFCD NFDD NFED NFFD
Adjustment Sensitivity at 100 psi Differential
50 50 100 200
Flow = GPM
Flow = GPM
Flow = GPM
Flow = GPM
40 40
75 150
30 30
50 100
20 20
10 25 50
10
0 1 2 3 4 5 0 1 2 3 4 5 0 1 2 3 4 5 0 1 2 3 4 5
Number of Turns Number of Turns Number of Turns Number of Turns

■ Maximum valve leakage at shutoff = less than 5 drops/min.

NF ✱ D – ✱ ✱ ✱
Nominal
Control** Orifice Options Seal
Orifice
C .33" dia. $ 21.60 L Standard Screw +$ 0.00 NFCD N Buna-N
F .33"
D .50" dia. $ 29.20 H Calibrated V Viton
Handknob with +$ 8.00 NFDD
E .69" dia. $ 55.80 Detent Lock G .50"
F .85" dia. $104.90 K Handknob +$ 5.00 NFED

H .69"
NFFD
I .85"

on Control Options
Relief Valves
Flow Control
+ - Valves
FULLY ADJUSTABLE NEEDLE WITH REVERSE FLOW CHECK

2 1
c 2
- +
b
Locating
Shoulder
b c Typical c Installation
Capacity1 Cartridge Cavity a b Torque
a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
Locating
2 Shoulder
25 GPM RPEC – LAN T - 10A 1.56 7/8”Cartridge Dimensions
2.00 2.06 2.25 30/35
Outlet Maximum Typical c Installation
50 GPM
Nominmal RPGCCartridge
– LAN T - Cavity
3A 1.88
a 1 1/8”
b 2.12 2.18 2.38 45/50
Torque
L H K
100Orifice
GPM Model
RPIC – LANCode
T - 16A 2.44 1 1/4” 2.44 2.47 2.69 (lb. ft.)
150/160
Inlet 1 a .16" dia. NCBB – LCN T - 162A 1.22 3/4” 1.59 - 1.73 25/30
2 200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Port .19" dia. NCCB – LCN T - 13A 1.38 7/8” 2.27 2.49 2.50 30/35
Performance Curves .25" dia. NCEB – LCN T - 5A 1.62 1 1/8” 2.35 2.82 2.73 45/50
RPCC Port RPEC .38" dia. NCFBRPGC
– LCN T - 16A RPIC1 1/4”
2.44 2.66 RPKC 2.91
3.06 150/160
1
.56" dia. NCGB –Typical
LCN Pressure
T - 18ARise 3.13 1 5/8” 3.31 3.50 3.47 350/375
5000 5000 5000 5000
Performance
5000
Curves 4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
NCBB
3000 NCCB
3000 NCEB
3000 NCFB
3000
NCGB
3000
2000 2000 2000 2000 2000
1000 1000 Adjustment Sensitivity at 100 psi Differential
1000 1000 1000
6 0 5 10 15 20 25 6 0 10 20 30 40 50 12 0 20 40 60 80 100 30 0 40 80 120 160 200 60 0 80 160 240 320 400

Flow = GPM
Flow = GPM
Flow = GPM
Flow = GPM
Flow = GPM
Flow = GPM
5 5 10 25 50
4 4 8 20 40
3 ■ Maximum
3 operating pressure6 = 5000 psi 15 30
2 2 4 10 20
1
■ Will1 accept maximum pressure
2 at Port 2. 5 10
0 1 2 3 4
■
5 Back 0 pressure
1 2 on
3 the4 tank
5 port0(port1 2)2 is directly
3 4 5additive0 at a
1 1:1
2 ratio
3 to
4 the
5 valve 0setting.
1 2 3 4 5
Number of Turns ■ FactoryNumber of Turns
pressure settings establishedNumber of Turns
at 4 GPM Number of Turns Number of Turns

■ Maximum
in 3/min./1000valve
psi,leakage
RPKC:=55indrops/min.
3/min./1000 psi.
NC ✱RP
✱ ✱ –C –✱✱C ✱ ✱
Maximum Nominal
Nominal Base Version Control** Cracking Pressure* Seal
Orifice C 12 GPM* $ 31.90 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
E 25.50
NCBB* .16" dia. $ $ 36.20
25 GPMB High Capacity C Tamper Resistant
L +$ 4.10Screw
Standard B 50 - 1500
+$ 0.00
psi +$
A 4 0.00
psi V Viton +$ 2.00
+$ 0.00 N Buna-N
G 25.50
NCCB .19" dia. $ $ 51.80
50 GPMC Low Capacity K Handknob H +$ 5.00 C
Calibrated 150 -+$
60008.00
psi +$
C 302.00
psi +$ 0.00 V Viton
NCCC .09" dia. $
I 26.70
100 GPM $ 97.30 Handknob with
N 60 - 800 psi +$ 1.00
Detent Lock E 75 psi
NCEB .25" dia. K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
NCEC .13" dia. $ 35.70 K Handknob
W 150 - 4500 psi +$ 0.00
NCFB .38" dia.
NCFC .28" dia.
NCGB .56" dia.
NCGC .38" dia. A, B, C, and W are standard set at 1000 psi.
6 *Cracking Pressure Ranges:
** See page 162 for information A and E ranges are not available
on Control Options in T-162A cavity.
Relief Valves
PILOT
Flow OPERATED,
Control Valves BALANCED PISTON
FIXED ORIFICE,
Full Adjustment 5 Turns PRESSURE COMPENSATED
+ -
2
Full Adjustment ± 3 Turns
+ -
2 1
L Control
c
X Control
b c
b 1
Locating
Shoulder
Capacity Cartridge Cavity a bCartridge Dimensions Torque
ModelTypical
Code L C K (lb. ft.)
Nominal c Installation
a 12Capacity
GPM RPCCCartridge
– LAN Cavity
T - 162A 1.22a b
3/4” 2.11 2.17 Torque
Model Code X L K 2.31 25/30
(lb. ft.)
2 a
.1-3 GPM RPEC – LAN
25 GPM T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet FXBA – XAN T - 162A 1.22 3/4” .82 2.11 2.55 25/30
2
.1-6.0 GPM RPGC – LAN
50 GPM T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
Port FXCA – XAN T - 13A 1.38 7/8” .75 2.00 2.25 30/35
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1 .1-12.0 GPM FXDA – XAN T - 5A 1.62 1 1/8” .69 2.12 2.38 45/50
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Port 1 .2-25 GPM FXEA – XAN T - 16A 2.44 1 1/4” .97 2.44 2.69 150/160
Performance Curves .2-50 GPM FXFA – XAN T - 18A 3.13 1 5/8” 1.19 2.81 3.06 350/375
RPCC
FXBA FXCA Typical Pressure Rise
FXDA FXEA FXFA
5000 5000 5000 5000
Typical Performance
5000
4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
30003 8
3000 15
3000 32
3000 60
3000
Flow = GPM
Flow = GPM
Flow = GPM
Flow = GPM
Flow = GPM
2000
2.25 2000
6 2000 2000 2000
12.25 24 45
1000 1000 1000 1000 1000
1.5 4 7.5 16 30
0 5 10 15 20 25 0 10 20 30 40 50 0 20 40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
0.75 2
3.75
Flow = GPM 8 Flow = GPM 15 Flow = GPM
0 1000 2000 3000 4000 5000
P= psi
■ Maximum
0
operating
P = psi
pressure =0 5000
1000 2000 3000 4000 5000
psi
1000 2000 3000 4000 5000
P = psi
0 1000 2000 3000 4000 5000
P = psi
0 1000 2000 3000 4000 5000
P = psi
■
■ Back pressure
50002)psiis directly additive at a 1:1 ratio to the valve setting.
■
■ Customer must specify flow setting at 4 GPM
Factory pressure settings established
■
■ Typical response
Accurate pressuretime 10 ms. control requires that a 200 psi minimum pressure differential be
compensated
maintained across the valve.
■ in3/min./1000
The psi, RPKC:
tuneable control in3/min./1000
option5 provides +/- 25%psi.variation from the nominal factory pre-set flow.
RP C – ✱ A
FX ✱ A ✱✱
Nominal
Nominal
Capacity Control**
Control** Adjustment Range
Adjustment Range Seal
Seal
Capacity
B C.1-312 GPM*
GPM $$ 31.90
30.80 L Non-adjustable
X Standard Screw +$ +$ 0.00
0.00 A Fixed
A 100 - 3000 psi +$
Orifice 0.00 N
+$ 0.00 N Buna-N
Buna-N +$ 0.00
E 25 GPM $ 36.20 C Factory
Tamper set
Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
C .1-6.0 GPM $ 30.80 at customer Customer must specify flow V Viton
G 50 GPM $ 51.80 K specified
Handknobflow +$ 5.00 C 150 - 6000 psi +$ 2.00
D I .1-12.0
100 GPM
GPM $ 97.30 N 60 - 800 psi +$ 1.00
L Tuning Adjustment
E K.2-25
200 GPM
GPM $$187.00
88.10 ±25% of customer Q 60 - 400 psi +$ 1.00
specified flow
F .2-50 GPM W 150 - 4500 psi +$ 0.00
K Handknob with
L control Adjustment Range Options:
on Control Options
Relief Valves
Flow Control Valves
FIXED ORIFICE, PRESSURE COMPENSATED WITH REVERSE FLOW CHECK
+
Full Adjustment ±- 3 Turns 2
+ -
L Control 2 1
c
X Control
b c
b 1
Locating
Shoulder
Shoulder
Typical c
Cartridge Dimensions Installation
Nominal Typical
ModelCartridge
Code L Cc K Installation
(lb. ft.)
a Cavity a b Torque
12Capacity
GPM RPCC – LAN
Model Code T - 162A 1.22 3/4” X
2.11 L
2.17 K
2.31 (lb. ft.)
25/30
a
2 25.1-3
GPMGPM RPEC FCBB
– LAN– XAN T - T10A
- 162A 1.22
1.56 3/4”
7/8” .82
2.00 2.11
2.06 2.55
2.25 25/30
30/35
2
Outlet
Port .1-6.0
50 GPM GPM RPGCFCCB
– LAN– XAN T - T3A- 13A 1.38
1.88 1 7/8”
1/8” .75
2.12 2.00
2.18 2.25
2.38 30/35
45/50
.1-12.0
100 FCDB
GPMGPM RPIC – XAN T - T16A
– LAN - 5A 1.62
2.44 111/4”
1/8” .69
2.44 2.12
2.47 2.38
2.69 45/50
150/160
Inlet 1
Port 1 .2-25
200 GPM GPM FCEB –
RPKC – LANXAN T - 18A16A
T - 2.44
3.13 1 1/4”
1 5/8” .97
2.81 2.44
2.94 2.69
3.06 150/160
350/375
.2-50 GPM FCFB – XAN T - 18A 3.13 1 5/8” 1.19 2.81 3.06 350/375
Performance Curves
Performance Curves
FCBB FCCB FCDB
FCEB FCFB
5000 5000 Reverse Free Flow Pressure
5000 Drop Based on Specified
5000 Flow Extremes 5000
4000 4000 4000 4000
P = psi
4000
300 300 150 150 200
P = psi
= psi
P = psi
P = psi
3000 3000 3000 3000 3000
psi
P = psi
P = psi
P = psi
P = psi
200
2000 2000
200 100
2000 2000
100 135
2000
P=P
.1 GPM .1 GPM .1 GPM .2 GPM .2 GPM
1000 1000 1000 1000 1000
100 3 GPM 100 50 50 65
0 5 10 15 20 25 0 10 20 30 6 GPM40 50 0 20 40 6012 GPM80 100 0 40 80 12025 GPM
160 200 0 80 160 50 GPM320 400
240
0 2 4 6 8 10 0 2 4 6 8 10 0 4 8 12 16 20 0 8 16 24 32 40 0 16 32 48 64 80
Flow = GPM ■ MaximumFlow = GPM pressure = 5000Flow
operating psi = GPM Flow = GPM Flow = GPM
■
■ Maximum
Back operating
pressure on the pressure
tank port=(port
50002)psi
■
■ Customer must specify flow setting
Factory pressure settings established at 4 GPM
■
■ Accurateresponse
Typical pressuretime
compensated
10 ms. control requires that a 200 psi minimum pressure differential be
maintained across the valve.
■ The
in tuneable control
3/min./1000 option
psi, RPKC: provides
5 in +/- 25%
3/min./1000 psi. variation from the nominal factory pre-set flow.
RP ✱C
FC ✱ B –
– ✱
✱ ✱
A✱✱
Nominal
Nominal
B .1-3 GPM $ 37.30 X Non-adjustable +$0.00 A Fixed Orifice +$ 0.00 N Buna-N +$ 0.00
E 25 GPM $ 36.20 C Factory Resistant
Tamper set +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
specified flow +$ 5.00 C 150 - 6000 psi +$ 2.00
DI .1-12.0 GPM $ 97.30
100 GPM N 60 - 800 psi +$ 1.00
L Tuning Adjustment
E K .2-25
200 GPM
GPM $187.00
$109.50 ±25% of customer Q 60 - 400 psi +$ 1.00
specified flow
F .2-50 GPM W 150 - 4500 psi +$ 0.00
K Handknob with
L control Adjustment Range Options:
on Control Options
Relief Valves
Flow
PILOT Control Valves
OPERATED, BALANCED PISTON
FULLY ADJUSTABLE, PRESSURE COMPENSATED WITH
REVERSE + - FLOW CHECK
2 2 1
- + c
b
Locating
c Shoulder Cartridge Dimensions
b
aLocating 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 25Nominal
GPM RPEC Typical
– LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet c Installation
Flow RPGC Cartridge T - Cavity a b Torque
ModelLAN
– L H2.18 K2.38
50 GPM 3A 1.88 1 1/8” 2.12 45/50
Range Code (lb. ft.)
a 100
.1-6GPM RPIC – LAN
2 Inlet 1 GPM FDBA – LAN T - T16A
- 13A 2.44
1.38 17/8”
1/4” 2.44
2.27 2.47
2.44 2.69
2.31 150/160
30/35
Port 200
.1-12GPM
GPM RPKC
FDCB– LAN
– LAN T - T18A
- 5A 3.13
1.62 11 5/8”
1/8” 2.81
2.35 2.94
2.82 3.06
2.73 350/375
45/50
Performance Curves .2-25 GPM FDEA – LAN T - 16A 2.44 1 1/4” 2.66 3.06 2.91 150/160
RPCC Port 1 RPEC.2-50 GPM FDFA RPGC

– LAN T - 18A 3.13RPIC
1 5/8” 3.31 3.50RPKC
3.47 350/375

Performance Curves
5000 5000 5000 5000 5000
FDBA 4000 FDCB 4000 FDEA 4000

FDFA 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
3000 3000 3000 3000 3000

2000 2000 Typical Performance
2000 2000 2000
1000 1000 1000 1000 1000
10 15 30 60
Flow = GPM
Flow = GPM
Flow = GPM
Flow = GPM
0 5 10 8 15 20 25 0 10 20 1230 40 50 0 20 40 24
60 80 100 0 40 80 48
120 160 200 0 80 160 240 320 400
Flow =6GPM Flow = 9GPM Flow = GPM
18 Flow = GPM
36 Flow = GPM
6
4
2
■ Maximum operating pressure = 5000 psi 12 24
12
3 6
0 1000 2000 3000 4000 5000 0 1000 2000 3000 4000 5000 0 1000 2000 3000 4000 5000 0 1000 2000 3000 4000 5000
■ Back pressure on the tank
P = psi P = port
psi (port 2) is directly additive
P = psi at a 1:1 ratio to the valve
P = psi setting.
■
Typical response timepressure
10 ms. = 5000 psi
■
■ Accurate pressure compensated
Maximum leakage = RPCC, RPEC: control
2 inrequires that psi,
3/min./1000 a 200 psi minimum
RPGC: pressurepsi,
3 in3/min./1000 differential
RPIC: 4 be
maintained
in3/min./1000 across the valve.
psi, RPKC: 5 in3/min./1000 psi.
RP ✱
FD ✱✱C –
– ✱
✱ A
✱✱✱
Nominal
Nominal
Flow Base Control** Adjustment Range Seal
C Range
BA .1-6 GPM $ 50.50 L Standard Screw +$ 0.00 FDBA N Buna-N
G 50 GPM $ 51.80 K Handknob +$ 5.00 A
C .1
150 6000 psi +$ 2.00
- 6- GPM
CB .1-12 GPM $ 73.20 H Calibrated +$ 8.00 V Viton
I 100 GPM $ 97.30 Handknob with N 60 - 800 psi
FDCB +$ 1.00
EA
K .2-25 GPM $128.70
200 GPM $187.00 Detent Lock A
Q .1
60--12 GPM
400 psi +$ 1.00
FA .2-50 GPM $254.60 K Handknob +$ 5.00 W 150 - 4500FDEA

psi +$ 0.00
A .1 - 25 GPM
Adjustment Range
FDFAOptions:
A, B,
A .1 C, and
- 50 W are standard set at 1000 psi.
GPM

on Control
Visit www.sunhydraulics.com Optionsand complete technical information on our full line of products.
for detailed
6
Flow Control Valves
FREE FLOW SIDE-TO-NOSE WITH BYPASS ORIFICE
2
b
c
Locating
Shoulder
1
Nominal Cartridge Cavity a b Torque
Outlet Capacity Model Code X lb. ft.
7.5 GPM CNAC – XCN T - 162A 1.22 3/4” .82 25/30
15 GPM CNCC – XCN T - 13A 1.38 7/8” .75 30/35
Inlet 1 120 GPM CNEC – XCN T - 5A 1.62 1 1/8” .69 45/50
60 GPM CNGC – XCN T - 16A 2.44 1 1/4” .97 150/160
120 GPM CNIC – XCN T - 18A 3.13 1 5/8” 1.19 350/375
Performance Curves
CNAC CNCC CNEC CNGC CNIC
Typical Pressure Drop for Nominal Cracking Pressures
200 200 200 200 200
150 150 150 150 150

P = psi
P = psi
P = psi
P = psi
P = psi

XAN XAN XAN XAN
XAN
0 2.5 5 7.5 10 0 10 15 20 0 10 20 30 40 0 25 50 75 100 0 100 150 200


■ * Orifice range = CNAC, CNCC: .015 - .062 in., CNEC: .015 - .078 in., CNGC: .015 - .094 in.,
CNIC: .015 - .125 in.

CN ✱ C – ✱ ✱ ✱
Nominal
Capacity Control** Cracking Pressure Seal
A 7.5 GPM $ 20.00 X Non-adjustable +$ 0.00 A 4 psi +$ 1.00 N Buna-N

C 15 GPM $ 20.00 B 15 psi +$ 1.00 V Viton
E 30 GPM $ 28.30 C 30 psi
G 60 GPM $ 48.20 D 50 psi
I 120 GPM $ 90.10 E 75 psi
F 100 psi
* Customer specified orifice setting range:

CNAC: .015 - .062 in.
CNCC: .015 - .062 in.
CNEC: .015 - .078 in.
** See page 162 for information CNGC: .015 - .094 in.
on Control Options CNIC: .015 - .125 in.
Relief Valves
Flow Control Valves
ELECTRO-PROPORTIONAL,
+ - NORMALLY CLOSED THROTTLE
e 2
2 1
c
b
Locating
d
Shoulder 1 Cartridge Dimensions
a 12 GPM RPCC – LAN T - 162A 1.22 3/4”Cartridge Dimensions
2.11 2.17 2.31 25/30
b Maximum Typical Installation
2 c 25 Nominal
GPM RPEC –Cartridge
LAN T - 10A 1.56 a 7/8” b 2.00 c 2.06d 2.25 30/35
Outlet Cavity e Torque
50 Capacity
GPM RPGCModel
– LAN Code T - 3A 1.88 1 1/8” 2.12 2.18 2.38 lb. ft.
45/50
Locating
Shoulder 7 GPM FPCC – MCN T - 13A 1.38 7/8” .75 2.76 1.47 30/35
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
2 Inlet 1 a
Outlet 200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
1 Inlet
5000 5000 5000 5000
FPCC
5000
4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
3000 Flow vs. Command 3000 3000

Flow vs. Pressure
3000
Differential 3000
2000 at 200 psi Differential 2000
Spool A 2000
Spool B
2000
Spool C
2000
10008 1000 4 1000 10 1000 15 1000
% Command
% Command
% Command
Flow = GPM
Flow = GPM
Flow = GPM
Flow = GPM
100% 100% 100%
"C" Spool 0 8 0 40 80 120 160 200 0 80 160 240 320 400
60 5 10 15 20 25 10 3 20 30 40 50 0 20 40 60 80 100
Flow = GPM Flow = GPM 75% Flow = GPM
6 Flow
75%= GPM
10
Flow = GPM75%
4 "B" Spool 2
50% 4 50% 50%
5
2 Maximum1operating pressure = 25%
"A" Spool
■ 5000 psi 2 25% 25%
80 100 Will accept0 maximum pressure

4000 5000at Port 2.
■
0 20 40 60 1000 2000 3000 0 1000 2000 3000 4000 5000 0 1000 2000 3000 4000 5000
% Command ■ Back pressure on the P = psi P = psi at a 1:1 ratio to the valve setting.
tank port (port 2) is directly additive P = psi

■ Maximum valve leakage = 6 in³/min. at 3000 psi
■ For
in optimum performance,
3/min./1000 psi, RPKC: 5 an amplifier with
in3/min./1000 psi.current sensing and adjustable dither should be used.
RP CC
FP ✱ C –– ✱
✱ ✱
✱✱✱
Nominal
Maximum
Nominal Base Control** Nominal Capacity Seal
C Capacity
EC 25 GPM
7 GPM $$112.00
36.20 CM Tamper Override +$
ManualResistant +$ 4.10
0.00 BA 50
1.5- GPM
1500 psi +$ 0.00
+$ 12.00 VN Viton
Buna-N +$ 2.00
(Standard)
B 3.5 GPM +$ 7.00 V Viton
I 100 GPM $ 97.30 NOTE: Coil must be N 60 - 800 psi +$ 1.00
ordered separately. Use C 7 GPM
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00
12V DC or 24V DC
W 150 - 4500 psi +$ 0.00
only. See page 167.

** See pagefor
Visit www.sunhydraulics.com 162 for information
detailed and complete technical information on our full line of products.
on Control Options
Relief Valves
Flow Control Valves
ELECTRO-PROPORTIONAL, NORMALLY OPEN THROTTLE
+ -
2
e
2 1
c
b
d
Locating 1
Shoulder
b a 12 GPM
Maximum RPCC –Typical
LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
Installation
c
2 Nominal
25Capacity
GPM RPEC
Cartridge
– LAN
Cavity
T - 10A 1.56
a b
7/8”
c
2.00
d
2.06
e
2.25
Torque
Outlet Model Code lb.30/35
ft.
Locating RPGC – LAN
Shoulder 50 7GPM
GPM FPCH – MCN T - 3A
T - 13A 1.88
1.38 1 7/8”
1/8” 2.12
.75 2.18
2.76 1.472.38 45/50
30/35
2 a 100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Outlet Inlet 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
1 InletCurves
Performance
5000 5000 5000 FPCH 5000 5000
4000 4000 4000 4000
P = psi
4000
Flow vs. Command Flow vs. Pressure3000
Differential
P = psi
P = psi
P = psi
P = psi
3000 3000 3000 3000

2000
at 200 psi Differential 2000
Spool A 2000
Spool B2000 Spool
2000 C
6 4.00 6 8
1000 1000 10000% 1000 1000
% Command
% Command
% Command
Flow = GPM
Flow = GPM
Flow = GPM
Flow = GPM
"C" Spool 0% 0%
3.00 6
04 4 60 0 40 80 120 160 200 0 80 160 240
5 10 15 20
"B" Spool
25 0 10 20 30 40 50 0
25% 20 40 80 100 25% 25% 320 400
Flow = GPM 2.00 Flow = GPM Flow = GPM Flow = GPM 4 Flow = GPM
2 50% 2 50% 50%
"A" Spool 1.00 2
■ Maximum operating pressure = 75%5000 psi 75% 75%
0 20 40 60 80
■ 100
Will accept
0
maximum pressure at Port 2. 0 1000 2000 3000 4000 5000
1000 2000 3000 4000 5000 0 1000 2000 3000 4000 5000
% Command P = psi P = psi P = psi
■ For
in optimum performance,
3/min./1000 psi, RPKC: 5an in3amplifier
/min./1000with
psi.current sensing and adjustable dither should be used.
RP CC
FP ✱ H – ✱ ✱✱
Nominal
Maximum
Nominal Base Control** Nominal Capacity Seal
C Capacity
C 7 GPM $112.00 D Manual Override +$ 0.00 A 1.5 GPM +$ 12.00 N Buna-N
(Standard)
G 50 GPM $ 51.80 K Handknob +$ 5.00 B 150
C 3.5 GPM
- 6000 psi 7.00
+$ 2.00 V Viton
NOTE: Coil must be
I 100 GPM $ 97.30 ordered separately. Use N
C 60 - 800 psi
5 GPM +$ 1.00
K 200 GPM $187.00 12V DC or 24V DC Q 60 - 400 psi +$ 1.00


on Control Options
Priority Flow Control
Cartridge Valves
Cartridge Type Page
1 3
2
Bypass / Restrictive, Fixed Orifice 76
1 3
2 Ventable, Bypass / Restrictive, Fixed Orifice 77
T-8A
4
3
1 Ventable, Bypass / Restrictive, Fixed Orifice with
2 78
1 Bypass / Restrictive Modulating Element 79

4 2

Priority Flow Control Valves
Relief Valves
BYPASS / RESTRICTIVE, FIXED ORIFICE
Full Adjustment ± 3 Turns
Full Adjustment
+ 5- Turns
+ - 3
L Control 1
2
X Control
2 1
b cc
b
3 Locating
Priority Locating
Flow Shoulder Typical Cartridge Dimensionsc Installation
Capacity Cartridge
Typical Cavity a b Torque
X Lc K Installation
Capacity Cartridge Code
Model Cavity a b (lb. ft.)
Torque
2 a L C K
.1-3 GPM Model Code– XAN
FRBA T - 163A 1.22 3/4” 1.25 2.55 2.77 (lb. ft.)
25/30
Bypass a 12 GPM RPCC – LAN T - 162A 1.221.38 3/4” 2.11 2.17 2.31 25/30
Flow .1-6.0 GPM FRCA – XAN T - 11A 7/8” 1.19 2.50 2.75 30/35
2
.1-12.0 GPM RPEC – LAN
25 GPM T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet FRDA – XAN T - 2A 1.38 1 1/8” 1.38 2.81 3.06 45/50
Inlet 1 50.2-25
GPM GPM RPGC – LAN
FREA – XAN
T - 3A
T - 17A 1.881.81 1 1/8”
1 1/4” 2.12
1.81 2.18
3.28 2.38
3.53 45/50
150/160
Inlet 1
100 GPM
.2-50 GPM RPICFRFA
– LAN
– XAN
T - 16A
T - 19A 2.442.50 1 1/4”
1 5/8” 2.44
2.75 2.47
3.94 2.69
4.19 150/160
350/375
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance Curves
Performance Curves
FRBA FRCA FRDA FREA FRFA
Typical Performance
Typical
Factory Pressure Rise
Priority Flow (GPM)
Priority Flow (GPM)
Flow (GPM)
psi (GPM)
Priority Flow (GPM)

Factory Inlet (GPM) Factory Inlet (GPM) Inlet (GPM) Factory Inlet (GPM) Factory Inlet (GPM)
Set Point * max. Set Point * max. Set Point * max. Set Point * max. Set Point * max.
5 5 10 20 50
5000 5000 5000 5000 5000
8* 15* 30* 60* 120*
4 4 8 16 40
4000
P = Flow
6 4000 10 4000 20 4000

P = psi
4000 40 80
P = psi
P = psi
P = psi
3 4 3 5 6 10 12 20 30 40
30002 Valve Set @ 3 GPM 3000 Valve Set @ 3 GPM 3000Valve Set @ 6 GPM 3000
Valve Set @ 12 GPM Valve Set @ 30 GPM
3000
2 4 8 20
Priority
Priority
8* 15* 30* 2000 60* 120*

2000
1
Valve Set @ 1 GPM 4
2000
1
Valve Set @ 1 GPM 5
2000
2 Valve Set @ 2 GPM 10 4 Valve Set @ 4 GPM 20 102000
Valve Set @ 10 GPM 40
1000
0 1000
0 1000
0 1000
0 01000
5000 3000 1000 0 1000 3000 5000 5000 3000 1000 0 1000 3000 5000 5000 3000 1000 0 1000 3000 5000 5000 3000 1000 0 1000 3000 5000 5000 3000 1000 0 1000 3000 5000
5 P10
Bypass0 pressure = psi15
Priority 20
pressure
25 Bypass pressure
0 10 P =20psi Priority
30 pressure
40 50 0
Bypass pressure 20 P = 40
psi Priority
60 pressure
80 100 0
Bypass pressure 40 80 Priority
P = psi 120 pressure
160 200 0
Bypass pressure P = psi
80 160 Priority
240 pressure
320 400
higher than priority higher than bypass higher than priority higher than bypass higher than priority Flow = higher
GPMthan bypass higher than priority Flow = GPM Flow = GPM
Flow = GPM Flow = GPM higher than bypass higher than priority higher than bypass
■
■
■ Will acceptmust
Customer maximum
specifypressure at PortFactory
a flow rating. 2. set flow ratings are within +/- 10% of the
■ requested
Back setting.
pressure on the tank port (port 2) is directly additive at a 1:1 ratio to the valve setting.
■
■ Pressurepressure
Factory at the bypass port
settings (port 2) may
established at 4exceed
GPM pressure at the priority port (port 3).
■
■ Maximum
Typical pressure
response at 10
time portms.
3 should be limited to 3000 psi.
■
■ Both priority
Maximum and bypass
leakage = RPCC,flowRPEC:
are usable up to the system
2 in 3/min./1000 operating
psi, RPGC: 3 inpressure.
3/min./1000 psi, RPIC: 4
in 3 /min./1000 3
■ Bypass flow ispsi,
notRPKC: 5 in
available /min./1000
until psi. requirements are satisfied.
priority flow
■
■ RPCC
Blocking minimum
prioritysetting for also
flow will all spring
block ranges
bypassisflow.
75 psi
RP
FR ✱ C
A – ✱ ✱
A✱
Nominal
Nominal
Capacity Control**
Adjustment Range
Range Seal
Seal
Capacity
C
B .1-3
12 GPM
GPM* $$ 31.90
34.50 LX Standard Screw
Non-adjustable +$ 0.00
+ 0.00 A
A 100 - 3000
Fixed psi
Orifice +$ 0.00
+ 0.00 N Buna-N +$ 0.00
N Buna-N
E 25 GPM $ 36.20 Factory set
specified flow +$ 5.00 C 150 - 6000 psi +$ 2.00
D .1-12.0 GPM
I 100 GPM $ 97.30 L Tuning Adjustment N 60 - 800 psi +$ 1.00
E .2-25
K 200 GPM
GPM $ 97.20
$187.00 ±25% of customer Q 60 - 400 psi +$ 1.00
specified flow
F .2-50 GPM W 150 - 4500 psi +$ 0.00
K Handknob for
L control
Maximum Inlet Flow: Priority
A, FlowWranges:
B, C, and are standard set at 1000 psi.
FRBA: 7.5 GPM NFRBA:
Option.1 is- 3standard
GPM set at 400 psi.
FRCA: 15 GPM QFRCA:.1
Option -is6.0 GPM set at 200 psi.
standard
FRDA: 30 GPM ** See page 162 for information *FRDA:.1
Minimum - 12.0 GPM
setting 75 psi on all ranges.
FREA: 60 GPM ** on
SeeControl
page 162 for information
Options FREA: .2 -may
Customer 25 GPMspecify pressure setting. +$ 1.10
FRFA: 120 GPM on Control Options FRFA: .2 - 50 GPM
VENTABLE, BYPASS / RESTRICTIVE, FIXED ORIFICE
4
1 3
b 2
4 c
Vent
3
Locating
Priority Shoulder
Flow Cartridge Dimensions
2 a Capacity Cartridge
Model Code
Cavity a b
X L K
Torque
(lb. ft.)
Bypass
Flow .1-6.0 GPM FVCA – XAN T - 21A 1.38 7/8” 1.78 3.09 3.34 30/35
.1-12.0 GPM FVDA – XAN T - 22A 1.38 1 1/8” 2.00 3.44 3.69 45/50
Inlet 1
.2-25 GPM FVEA – XAN T - 23A 1.81 1 1/4” 2.50 3.94 4.19 150/160
.2-50 GPM FVFA – XAN T - 24A 2.50 1 5/8” 3.16 4.76 5.01 350/375
Performance Curves
FVCA FVDA FVEA FVFA
Typical Performance
Priority Flow (GPM)
Priority Flow (GPM)
Priority Flow (GPM)
Priority Flow (GPM)

Factory Inlet (GPM) Factory Inlet (GPM) Factory Inlet (GPM) Factory Inlet (GPM)
Set Point * max. Set Point * max. Set Point * max. Set Point * max.
5 10 20 50
15* 30* 60* 120*
4 8 16 40
10 20 40 80
3 5 6 10 12 20 30 40
2 4 8 20
15* 30* 60* 120*
1 5 2 10 4 20 10 40
0 0 0 0
5000 3000 1000 0 1000 3000 5000 5000 3000 1000 0 1000 3000 5000 5000 3000 1000 0 1000 3000 5000 5000 3000 1000 0 1000 3000 5000
Bypass pressure P = psi Priority pressure Bypass pressure P = psi Priority pressure Bypass pressure P = psi Priority pressure Bypass pressure P = psi Priority pressure
higher than priority higher than bypass higher than priority higher than bypass higher than priority higher than bypass higher than priority higher than bypass

■ Nominal vent flow = 46 in³/min.
■ Pressure at the bypass port (port 2) may exceed pressure at the priority port (port 3).
■ Both priority and bypass flow are usable up to the system operating pressure.
■ Bypass flow is not available until priority flow requirements are satisfied, except when the valve
is vented. When port 4 (vent) is open, all flow diverts to port 2 if pressure at port 1 (inlet) is
150 psi or higher.
■ Using a pressure control on port 4 will limit the pressure at the priority port (port 3). If pressure on
the bypass port (port 2) exceeds the setting of the pressure control, priority flow will be shut off and
all the flow will go out the bypass port.
■ Blocking priority flow will also block bypass flow.
FV ✱ A – ✱ A ✱
Nominal
C .1-6.0 GPM $54.80 X Non-adjustable factory set +$0.00 A Fixed Orifice +$0.00 N Buna-N
at customer specified flow
D .1-12.0 GPM $81.00 Customer must specify flow V Viton
L Tuning Adjustment ±25%
E .2-25 GPM $146.50 of customer specified flow
F .2-50 GPM $272.50 K Handknob

(includes L controls)
Maximum Inlet Flow: Priority Flow ranges:

FVCA: 15 GPM FVCA: .1 - 6.0 GPM
FVDA: 30 GPM FVDA: .1 - 12.0 GPM
FVEA: 60 GPM **See page 162 for information FVEA: .2 - 25 GPM
FVFA: 120 GPM on Control Options FVFA: .2 - 50 GPM
VENTABLE, BYPASS / RESTRICTIVE, FIXED ORIFICE WITH INTEGRAL
T-8A
4 The -8 control option allows the pilot control valve to be incorporated directly
into the end of the priority flow control cartridge via the T-8A cavity. These pilot
1 3
b control cartridges are sold separately and include electro-proportional, solenoid,
2 air pilot, and hydraulic pilot operation. See Pilot Control Cartridges on page 121.
4 c
Vent
3
Priority Shoulder
Flow Typical c Installation
Model Code 8 (lb. ft.)
2 a .1-6.0 GPM FVCA – 8AN T - 21A 1.38 7/8” 1.78 30/35
Bypass
Flow .1-12.0 GPM FVDA – 8AN T - 22A 1.38 1 1/8” 1.78 45/50
Inlet 1 .2-25.0 GPM FVEA – 8AN T - 23A 1.81 1 1/4” 1.78 150/160
2-50.0 GPM FVFA – 8AN T - 24A 2.50 1 5/8” 1.78 350/375
Performance Curves
FVCA-8 FVDA-8 FVEA-8 FVFA-8
Typical Performance
Priority Flow (GPM)
Priority Flow (GPM)
Priority Flow (GPM)
Factory Inlet (GPM) Factory Inlet (GPM) Factory Inlet (GPM) Priority Flow (GPM) Factory Inlet (GPM)
Set Point * max. Set Point * max. Set Point * max. Set Point * max.
5 10 20 50
15* 30* 60* 120*
4 8 16 40
10 20 40 80
3 5 6 10 12 20 30 40
2 4 8 20
15* 30* 60* 120*
1 5 2 10 4 20 10 40
0 0 0 0
5000 3000 1000 0 1000 3000 5000 5000 3000 1000 0 1000 3000 5000 5000 3000 1000 0 1000 3000 5000 5000 3000 1000 0 1000 3000 5000
Bypass pressure P = psi Priority pressure Bypass pressure P = psi Priority pressure Bypass pressure P = psi Priority pressure Bypass pressure P = psi Priority pressure
higher than priority higher than bypass higher than priority higher than bypass higher than priority higher than bypass higher than priority higher than bypass

■ Nominal vent flow = 46 in³/min.
■ Pressure at the bypass port (port 2) may exceed pressure at the priority port (port 3).
■ Both priority and bypass flow are usable up to the system operating pressure.
■ Bypass flow is not available until priority flow requirements are satisfied, except when the valve
is vented. When port 4 (vent) is open, all flow diverts to port 2 if pressure at port 1 (inlet) is
150 psi or higher.
■ Using a pressure control on port 4 will limit the pressure at the priority port (port 3). If pressure on the
bypass port (port 2) exceeds the setting of the pressure control, priority flow will be shut off and all the
flow will go out the bypass port.
■ Blocking priority flow will also block bypass flow.
■ The main stage valve should first be installed to the correct torque value followed by the T-8A pilot
control section into the main stage valve to its required torque value.
FV ✱ A – 8 A ✱
Nominal
C .1-6.0 GPM $58.80 8 T-8A cavity in hex body +$0.00 A Fixed Orifice +$0.00 N Buna-N
for pilot operation (Pilot
D .1-12.0 GPM $85.00 valve to be ordered Customer must specify flow V Viton
separately)
E .2-25 GPM
F .2-50 GPM
Maximum Inlet Flow: Priority Flow ranges:

FVCA: 15 GPM FVCA: .1 - 6.0 GPM
FVDA: 30 GPM FVDA: .1 - 12.0 GPM
FVEA: 60 GPM **See page 162 for information FVEA: .2 - 25 GPM
FVFA: 120 GPM on Control Options FVFA: .2 - 50 GPM
BYPASS / RESTRICTIVE MODULATING ELEMENT
b 3
Locating 1
Shoulder
4 2
4
Port
a Typical c Installation
3
Port Model Code X (lb. ft.)
15 GPM LHDA – XFN T - 31A 3.34 7/8” 1.18 30/35
2 30 GPM LHFA – XFN T - 32A 3.63 1 1/8” 1.31 45/50
Port
60 GPM LHHA – XFN T - 33A 4.50 1 1/4” 1.63 150/160
120 GPM LHJA – XFN T - 34A 5.50 1 5/8” 2.00 350/375
1 Port

■ Bypass flow is not available until priority flow requirements are satisfied.
■ Bypass pressure at port 4 can be higher than pressure at control port 2.
■ Priority flow can be turned on or off with a pilot sized solenoid valve on port 1.

LH ✱ A – X ✱ ✱
Maximum
Inlet Flow Control** Adjustment Range Seal
D 15 GPM $ 71.30 X Non-adjustable +$ 0.00 E 75 - 100 psi +$ 0.00 N Buna-N
F 30 GPM $ 92.80 F 100 - 140 psi +$ 0.00 V Viton
H 60 GPM
J 120 GPM

on Control Options
NOTES

Flow Divider / Combiner
Cartridge Valves
Cartridge Type Page
4
3
2
Divider 82
4
3 Divider / Combiner, Closed Center 83
2
4
3 Synchronizing Divider / Combiner 84
2
4 High Capacity Divider / Combiner,

3
Closed Center 85
2

Flow Divider / Combiner Valves
DIVIDER
b
c 4
Locating 3
Shoulder
2
4
Port
3
Capacity Typical Installation
Port Min/Max Cartridge Cavity a b c d Torque
.6-3 GPM FSBD – XAN T - 31A 3.35 7/8” .75 .14 30/35
2
1.5-8 GPM FSCD – XAN T - 31A 3.35 7/8” .75 .14 30/35
Port
Working 3-15 GPM FSDD – XAN T - 32A 3.63 1 1/8” .69 .15 45/50
d Parts
Clearance 6-30 GPM FSED – XAN T - 33A 4.50 1 1/4” .97 .21 150/160
Port 1 Not Used
12-60 GPM FSFD – XAN T - 34A 5.50 1 5/8” 1.19 .27 350/375
Performance Curves
Operating Characteristics
FSBD-XAN FSCD-XAN FSDD-XAN
Percentage of Flow
Percentage of Flow
Percentage of Flow
15 GPM
8 GPM
3 GPM
Port 4 Port 2 52.5 Port 4 Port 2 52.5 Port 4 Port 2 53.5

50 50 50
Input Flow
Input Flow
Input Flow
at Port 3
at Port 3
at Port 3
Port 2 Port 4
47.5 Port 2 Port 4
47.5 Port 2 Port 4 46.5
Port 4 Port 2 Port 4 Port 2 Port 4 Port 2
0.6 GPM
54.5 54.5 56.5

1.5 GPM
3 GPM
50 50 50
5000 4000 3000 2000 1000 0 1000 2000 3000 4000 5000 5000 4000 3000 2000 1000 0 1000 2000 3000 4000 5000 5000 4000 3000 2000 1000 0 1000 2000 3000 4000 5000
Port 4 > Port 2 Differential Port 2 > Port 4 Port 4 > Port 2 Differential Port 2 > Port 4 Port 4 > Port 2 Differential Port 2 > Port 4
Pressure (psi) Pressure (psi) Pressure (psi)
FSED-XAN FSFD-XAN
60 GPM
Percentage of Flow
Percentage of Flow
30 GPM
Port 4 Port 2 Port 4 Port 2 53.5

53.5
50 50
Input Flow
Input Flow
at Port 3
at Port 3
Port 4 46.5 Port 2 Port 4

46.5
Port 2
Port 4 Port 2 Port 4 Port 2
56.5 56.5
12 GPM
6 GPM
50 50
Port 2 Port 4 43.5 Port 2 Port 4 43.5
5000 4000 3000 2000 1000 0 1000 2000 3000 4000 5000 5000 4000 3000 2000 1000 0 1000 2000 3000 4000 5000
Port 4 > Port 2 Differential Port 2 > Port 4 Port 4 > Port 2 Differential Port 2 > Port 4
Pressure (psi) Pressure (psi)

■ This valve is a divider only; any attempt to flow backwards through the valve is not advised.
■ Divisional accuracy at maximum rated input flow = FSBD: ±2.5%, FSCD, FSDD, FSED, FSFD: ±3.5%
■ Divisional accuracy at minimum rated input flow = FSBD: ±4.5%, FSCD, FSDD, FSED, FSFD: ±6.5%
■ Pressure drop at maximum input flow = 250 psi
■ Pressure drop at minimum input flow = 10 psi
■ Below the minimum flow rating there is not enough flow for the valve to modulate. It is effectively
a tee. If flow starts at zero and rises, there will be no dividing control until the flow reaches the
minimum rating.
FS ✱ D – X ✱ ✱
Nominal
Control Flow Proportion Seal
Capacity
B .6-3 GPM $ 66.60 X Non-adjustable +$ 0.00 A 50/50 Flow Split +$ 0.00 N Buna-N
C 1.5-8 GPM $ 66.60 B* 40/60 Flow Split +$ 6.00 V Viton
D 3-15 GPM $ 85.60 C* 33/67 Flow Split
E 6-30 GPM
F 12-60 GPM $253.00 * Port 4 is always high
percentage flow.
Reverse Flow Path is unpredictable

Divisional Accuracy =
FSCD, FSDD, FSED and FSFD:
± 6.5 % at minimum input flow
± 3.5 % at maximum input flow
FSBD:
DIVIDER / COMBINER, CLOSED CENTER
b
c 4 Note: Closed center valves have spring centered internal spools that provide
Locating 3 blocked flow paths when centered. Centering occurs when the Port 3 flow
Shoulder
2 is also blocked. This internal blocking isolates Port 2 and 4 from cross flow.
4
Port
a
3 Capacity Typical Installation
.6-3 GPM FSBA – XAN T - 31A 3.35 7/8” .75 .65 30/35
2 1.5-8 GPM FSCA – XAN T - 31A 3.35 7/8” .75 .65 30/35
Port
Working
3-15 GPM FSDA – XAN T - 32A 3.63 1 1/8” .69 .77 45/50
d Parts
Clearance
6-30 GPM FSEA – XAN T - 33A 4.50 1 1/4” .97 .99 150/160
Port 1 Not Used 12-60 GPM FSFA – XAN T - 34A 5.50 1 5/8” 1.19 .91 350/375
Performance Curves
FSBA-XAN FSCA-XAN FSDA-XAN

Percentage of Flow
Percentage of Flow
Percentage of Flow
15 GPM
8 GPM
3 GPM

50 50 50
Input Flow
Input Flow
Input Flow
at Port 3
at Port 3
at Port 3
Port 2 Port 4
47.5 Port 2 Port 4
47.5 Port 2 Port 4 47.5
0.6 GPM
54.5 54.5 54.5

1.5 GPM
3 GPM
50 50 50
5000 4000 3000 2000 1000 0 1000 2000 3000 4000 5000 5000 4000 3000 2000 1000 0 1000 2000 3000 4000 5000 5000 4000 3000 2000 1000 0 1000 2000 3000 4000 5000
Dividing - Port 4 > Port 2 Differential Dividing - Port 2 > Port 4 Dividing - Port 4 > Port 2 Differential Dividing - Port 2 > Port 4 Dividing - Port 4 > Port 2 Differential Dividing - Port 2 > Port 4
Combining - Port 2 > Port 4 Pressure Combining - Port 4 > Port 2 Combining - Port 2 > Port 4 Pressure Combining - Port 4 > Port 2 Combining - Port 2 > Port 4 Pressure Combining - Port 4 > Port 2
(psi) (psi) (psi)
FSEA-XAN FSFA-XAN
60 GPM
Percentage of Flow
Percentage of Flow
30 GPM

52.5
50 50
Input Flow
Input Flow
at Port 3
at Port 3

47.5
Port 2
54.5 54.5
12 GPM
6 GPM
50 50
5000 4000 3000 2000 1000 0 1000 2000 3000 4000 5000 5000 4000 3000 2000 1000 0 1000 2000 3000 4000 5000
Dividing - Port 4 > Port 2 Differential Dividing - Port 2 > Port 4 Dividing - Port 4 > Port 2 Differential Dividing - Port 2 > Port 4
Combining - Port 2 > Port 4 Pressure Combining - Port 4 > Port 2 Combining - Port 2 > Port 4 Pressure Combining - Port 4 > Port 2
(psi) (psi)

■ Divisional accuracy at rated maximum input flow = 50% ±2.5%
■ Divisional accuracy at rated minimum input flow = 50% ±4.5%
a tee. If flow starts at zero and rises, there will be no dividing or combining control until the flow
reaches the minimum rating.
■ Divisional and combining accuracy are equal.

FS ✱ A – X A ✱
Nominal
Capacity
B .6-3 GPM $101.40 X Non-adjustable +$ 0.00 A 50/50 Flow Split +$ 0.00 N Buna-N
C 1.5-8 GPM $101.40 V Viton
D 3-15 GPM
E 6-30 GPM
F 12-60 GPM
Divisional Accuracy (Combining and Dividing) =

Visit wwwsunhydraulics.com for detailed and complete technical information on our full line of products.
SYNCHRONIZING DIVIDER / COMBINER
b
c 4
Locating 3
Shoulder
2
4
Port
a Typical Installation
3 Capacity
.6-3 GPM FSBS – XAN T - 31A 3.35 7/8” .75 .65 30/35
2 1.5-8 GPM FSCS – XAN T - 31A 3.35 7/8” .75 .65 30/35
Port
Working 3-15 GPM FSDS – XAN T - 32A 3.63 1 1/8” .69 .77 45/50
d Parts
Clearance 6-30 GPM FSES – XAN T - 33A 4.50 1 1/4” .97 .99 150/160
Port 1 Not Used 12-60 GPM FSFS – XAN T - 34A 5.50 1 5/8” 1.19 .91 350/375
Performance Curves
FSBS-XAN FSCS-XAN Percentage of Flow FSDS-XAN

Percentage of Flow
Percentage of Flow
15 GPM
8 GPM
3 GPM

50 50 50
Input Flow
Input Flow
Input Flow
at Port 3
at Port 3
at Port 3
Port 2 Port 4
47.5 Port 2 Port 4
47.5 Port 2 Port 4 47.5
0.6 GPM
54.5 54.5 54.5

1.5 GPM
3 GPM
50 50 50
5000 4000 3000 2000 1000 0 1000 2000 3000 4000 5000 5000 4000 3000 2000 1000 0 1000 2000 3000 4000 5000 5000 4000 3000 2000 1000 0 1000 2000 3000 4000 5000
(psi) (psi) (psi)
FSES-XAN FSFS-XAN
60 GPM
Percentage of Flow
Percentage of Flow
30 GPM

52.5
50 50
Input Flow
Input Flow
at Port 3
at Port 3

47.5
Port 2
54.5 54.5
12 GPM
6 GPM
50 50
5000 4000 3000 2000 1000 0 1000 2000 3000 4000 5000 5000 4000 3000 2000 1000 0 1000 2000 3000 4000 5000
Dividing - Port 4 > Port 2 Differential Dividing - Port 2 > Port 4 Dividing - Port 4 > Port 2 Differential Dividing - Port 2 > Port 4
Combining - Port 2 > Port 4 Pressure Combining - Port 4 > Port 2 Combining - Port 2 > Port 4 Pressure Combining - Port 4 > Port 2
(psi) (psi)

■ Divisional accuracy at rated maximum input flow = 50% ±2.5%
■ The synchronization feature provides bi-directional static error correction.
FS ✱ S – X A ✱
Nominal
Capacity Control Flow Proportion Seal
B .6-3 GPM $108.00 X Non-adjustable +$ 0.00 A 50/50 Flow Split +$ 0.00 N Buna-N
C 1.5-8 GPM $108.00 V Viton
D 3-15 GPM
E 6-30 GPM
F 12-60 GPM
Synchronizing Flow per Leg:
FSBS: .16 - .25 GPM
FSCS: .2 - .5 GPM
FSDS: .3 - .6 GPM
FSES: .8 - 1.5 GPM
FSFS: 2.4 - 3.5 GPM
HIGH CAPACITY DIVIDER / COMBINER, CLOSED CENTER
b
c 4 Note: Closed center valves have spring centered internal spools that provide
Locating 3 blocked flow paths when centered. Centering occurs when the Port 3 flow
Shoulder is also blocked. This internal blocking isolates Port 2 and 4 from cross flow.
2
4
Port
3
a Typical Installation
Capacity Cartridge Cavity a b c d Torque
Port Min/Max Model Code (lb. ft.)
2-10 GPM FSCH – XAN T - 31A 3.35 7/8” .75 .65 30/35
2 4-20 GPM FSDH – XAN T - 32A 3.63 1 1/8” .69 .77 45/50
Port
Working
8-40 GPM FSEH – XAN T - 33A 4.50 1 1/4” .97 .99 150/160
Parts
d
Clearance
15-80 GPM FSFH – XAN T - 34A 5.50 1 5/8” 1.19 .91 350/375
Port 1 Not Used
Performance Curves
Constant Command - Varying Flow
FSCH-XAN FSDH-XAN FSEH-XAN
20 GPM
10 GPM
Percentage of Flow
Percentage of Flow
Percentage of Flow
40 GPM
Port 4 Port 2 54 Port 4 Port 2 54 Port 4 Port 2 54
50 50 50
Input Flow
Input Flow
Input Flow
at Port 3
at Port 3
at Port 3
Port 2 Port 4
46 Port 2 Port 4
46 Port 2 Port 4 46
56.5 56.5 56.5
4 GPM
2 GPM
8 GPM
50 50 50
5000 4000 3000 2000 1000 0 1000 2000 3000 4000 5000 5000 4000 3000 2000 1000 0 1000 2000 3000 4000 5000 5000 4000 3000 2000 1000 0 1000 2000 3000 4000 5000
(psi) (psi) (psi)
FSFH-XAN
Percentage of Flow
80 GPM
Port 4 Port 2 54
50
Input Flow
at Port 3
Port 2 Port 4 46
Port 4 Port 2
56.5
15 GPM
50
Port 2 Port 4 43.5
5000 4000 3000 2000 1000 0 1000 2000 3000 4000 5000
Dividing - Port 4 > Port 2 Differential Dividing - Port 2 > Port 4
Combining - Port 2 > Port 4 Pressure Combining - Port 4 > Port 2
(psi)

■ Divisional accuracy at rated maximum input flow = 50% ±4%

FS ✱ H – X A ✱
Nominal
Capacity
C 2-10 GPM $104.10 X Non-adjustable +$ 0.00 A 50/50 Flow Split +$ 0.00 N Buna-N
D 4-20 GPM $135.20 V Viton
E 8-40 GPM
F 15-80 GPM

NOTES

Logic Elements
Cartridge Type Page
Unbalanced Poppet, Pilot-to-Close

3 88
Switching Element
1
2 3
Unbalanced Poppet, Pilot-to-Close Switching

T-8A
89
Cav
Element with Integral Pilot Control Cavity
1
Unbalanced Poppet, Pilot-to-Open

3 90
Switching Element
1
Normally Open Modulating Element 91

1 3
Normally Closed Modulating Element 92

1 3
4 3 Normally Open, Direct Operated 93

1
4 3 Normally Open, Vent-to-Operate 94

1
Normally Open, Vent-to-Operate with Integral

T-8A
Cav 3 95
Pilot Control Cavity
4 1
3 Normally Open, Pressure Adjustable 96

4 1
4 3 Normally Closed, Direct Operated 97

1
3 Normally Closed, Pressure Adjustable 98

4 1
4 3 Normally Closed, Vent-to-Operate 99

1
Normally Closed, Vent-to-Operate with

T-8A
Cav 3 100
4 1

Logic Elements
UNBALANCED POPPET, PILOT-TO-CLOSE SWITCHING ELEMENT
2 2 2 2 3 2
b 3
3 3 3
c
1 1 1 1 1
3 LO*A LO*B LO*C LO*D LO*O

Port Locating
Shoulder
a Capacity Model Code X E (lb. ft.)
2
Port 25 GPM LODC – XDN T - 11A 1.38 7/8” 1.19 1.19 30/35
50 GPM LOFC – XDN T - 2A 1.38 1 1/8” 1.38 1.38 45/50
Port 1 100 GPM LOHC – XDN T - 17A 1.81 1 1/4” 1.81 1.81 150/160
200 GPM LOJC – XDN T - 19A 2.50 1 5/8” 2.31 2.31 350/375
Performance Curves
LOD* LOF* LOH* LOJ*
Full Open Pressure Drop
200 300 300 300
150
P = psi
P = psi
P = psi
P = psi
200 200 200

100
100 100 100
50
0 5 10 15 20 25 0 10 20 30 40 50 0 25 50 75 100 0 50 100 150 200


■ Area ratio: A3 to A1 = 1.8:1
■ Control orifice diameter = LODA, LODB, LODD, LOFA, LOFB, LOFD:.021 in., LOHA, LOHB,
LOHD: .031 in., LOJA, LOJB, LOJD: .035 in.
■ Pilot volume for complete shift = LOD*: .04 in³/min., LOF*: .07 in³/min., LOH*: .25 in³/min.,
LOJ*: .42 in³/min.
■ These valves are pressure responsive at all three ports, therefore it is essential to consider all aspects of
system operation through a complete cycle. Pressure changes at any one port may cause a valve to
switch from a closeld to an open position, or vice versa. All possible pressure changes in the complete
circuit must be considered to assure a safe, functional system design.

LO ✱ ✱ – ✱✱✱
Nominal Cracking Pressure
Version Control** Seal
Capacity A, B, C, D Versions
D 25 GPM $ 34.40 A Spring biased closed +$ 3.70 X Non-adjustable +$ 0.00 D 50 psi at Port 1 +$ 0.00 N Buna-N
Port 1 pilot source (30 psi to close
F 50 GPM $ 46.10 at Port 3 for V Viton
B Spring biased closed +$ 3.70 Available in B and C O Version)
H 100 GPM $ 77.70 Port 2 pilot source Versions Only
J 200 GPM $ 145.10 C Spring biased closed +$ 0.00 E SAE-4 Port in Hex
Port 3 pilot source Body, Port 3 blocked
D Spring biased closed +$15.00 Available in D and F

higher of Ports 1or 2 Capacities Only
pilot source
L Stroke Adjustment
O Spring biased open
Port 3 pilot source

on Control Options
Logic Elements
UNBALANCED POPPET, PILOT-TO-CLOSE SWITCHING ELEMENT WITH
INTEGRAL PILOT CONTROL CAVITY
2 3 2 3
The -8 control option allows a
2 3
pilot control valve to be incorporated
directly into the end of the cartridge via
b T-8A T-8A T-8A
the T-8A cavity. These pilot control
Cav Cav Cav cartridges are sold separately and
include solenoid and air pilot operation.
c 1 1 See Pilot Control Cartridges on
1
3 page 121.
LO*A-8 LO*B-8 LO*D-8
Port Locating
Shoulder
2 Nominal Typical Installation
a Cartridge Cavity a b c Torque
Port Capacity Model Code (lb. ft.)
25 GPM LODA – 8DN T - 11A 1.38 7/8” 1.19 30/35
1 Port 50 GPM LOFA – 8DN T - 2A 1.38 1 1/8” 1.38 45/50
100 GPM LOHA – 8DN T - 17A 1.81 1 1/4” 1.81 150/160
200 GPM LOJA – 8DN T - 19A 2.50 1 5/8” 2.31 350/375
Performance Curves
LOD*-8 LOF*-8 LOH*-8 LOJ*-8

200 300 300 300
150
P = psi
P = psi
P = psi
P = psi
200 200 200

100
100 100 100
50
0 5 10 15 20 25 0 10 20 30 40 50 0 25 50 75 100 0 50 100 150 200


■ Control orifice diameter = LOD*-8, LOD*-8, LOF*-8, LOF*-8: .021 in., LOH*, LOH*-8: .031 in.,
LOJ*, LOJ*-8: .035 in.
switch from a closed to an open position, or vice versa. All possible pressure changes in the complete

LO ✱ ✱ – 8 ✱✱
Capacity A, B, D Versions
D 25 GPM $ 34.40 A Spring biased closed +$ 3.70 8 T-8A Cavity in +$ 4.00 D 50 psi at Port 1 +$0.00 N Buna-N
Port 1 pilot source hex body for
F 50 GPM $ 46.10 pilot operation V Viton
B Spring biased closed +$ 3.70 (Pilot valve to
H 100 GPM $ 77.70 Port 2 pilot source be ordered
separately)
J 200 GPM $ 145.10 D Spring biased closed +$15.00
higher of Ports 1or 2
pilot source

on Control Options
Logic Elements
UNBALANCED POPPET, PILOT-TO-OPEN SWITCHING ELEMENT
2
b c 3
1
3
Port Locating
Shoulder
Nominal Typical Installation
a Capacity Cartridge Cavity a b c Torque
2
Port 15 GPM LKDC – XDN T - 11A 1.38 7/8” 1.19 30/35
30 GPM LKFC – XDN T - 2A 1.38 1 1/8” 1.38 45/50
Port 1 60 GPM LKHC – XDN T - 17A 1.81 1 1/4” 1.81 150/160
120 GPM LKJC – XDN T - 19A 2.50 1 5/8” 2.31 350/375
Performance Curves
LKDC LKFC LKHC LKJC
200 200 200 200
150 150 150 150

P = psi
P = psi
P = psi
P = psi
100 100 100 100
50 50 50 50
0 5 10 15 0 10 20 30 0 20 40 60 0 40 80 100

■ Control orifice diameter = LKDC: .031 in., LKFC: .035 in., LKHC: .062 in., LKJC: .094 in.
■ Pilot volume for complete shift = LKDC: .02 in³/min., LKFC: .06 in³/min., LKHC: .15 in³/min.,
LKJC: .30 in³/min.
switch from a closed to an open position, or vice versa. All possible pressure changes in the complete

LK ✱ ✱ – ✱✱✱
Capacity
D 15 GPM $ 38.40 C Port 3 pilot source +$ 0.00 X Non-adjustable +$ 0.00 D 30 psi at Port 3 +$ 0.00 N Buna-N
F 30 GPM $ 51.80 Available in D and F V Viton

Capacities Only
H 60 GPM
L Manual Release
J 120 GPM

on Control Options
Logic Elements
NORMALLY OPEN MODULATING ELEMENT
2 2
c
1 3 1 3
3
Port Locating LP*A LP*C
Shoulder
a Capacity Model Code X L (lb. ft.)
2
Port 7.5 GPM LPBC – XHN T - 163A 1.22 3/4” 1.25 2.55 25/30
15 GPM LPDC – XHN T - 11A 1.38 7/8” 1.19 2.50 30/35
Port 1 30 GPM LPFC – XHN T - 2A 1.38 1 1/8” 1.38 2.82 45/50
60 GPM LPHC – XHN T - 17A 1.81 1 1/4” 1.81 3.27 150/160
120 GPM LPJC – XHN T - 19A 2.50 1 5/8” 2.31 3.94 350/375
Performance Curves
LPBC LPDC LPFC LPHC LPJC
Capacity as a Restrictive Compensator
5 20 40 80 160
Flow in GPM
Flow in GPM
Flow in GPM
Flow in GPM
Flow in GPM
4 16 32
60 120
3 12 24
40 80
2 8 16
1 4 8 20 40
0 .025 .050 .075 .100 .125 .150 .175 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0 0.2 0.4 0.6 0.8 1.0 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 0 0.4 0.8 1.2 1.6 2.0
Orifice Diameter in inches Orifice Diameter in inches Orifice Diameter in inches Orifice Diameter in inches Orifice Diameter in inches

■ Maximum leakage at 150 SUS, port 3 = 1 in³/min.
■ Control orifice diameter = LPB*, LPD*, LPF*: .016 in., LPH*, LPJ*: .021 in.

LP ✱ ✱ – ✱✱✱
Nominal
Version Control** Control Pressure Seal
Capacity
B 7.5 GPM $ 40.20 A Internal pilot Port 1 +$ 3.70 X Non-adjustable +$ 0.00 D 50 psi +$ 0.00 N Buna-N
to Port 3 (mainstage
D 15 GPM $ 40.20 reducing element) F 100 psi +$ 0.00 V Viton
F 30 GPM $ 54.00 C External pilot +$ 0.00 Available in D G*150 psi

(restrictive Adjustment Range only
H 60 GPM $ 98.70 compensator) H 200 psi
L Tuning Adjustment +$ 8.00
J 120 GPM $ 199.80 + 25% of customer
specified flow
* G Adjustment Range
** See page 162 for information not available in
on Control Options LPBA, LPBC.
Logic Elements
NORMALLY CLOSED MODULATING ELEMENT
2 2
c
1 3 1 3
3
Port Locating LR*A LR*C
Shoulder
a Capacity Model Code X L (lb. ft.)
2
Port 7.5 GPM LRBC – XHN T - 163A 1.22 3/4” 1.25 2.55 25/30
15 GPM LRDC – XHN T - 11A 1.38 7/8” 1.19 2.50 30/35
Port 1 30 GPM LRFC – XHN T - 2A 1.38 1 1/8” 1.38 2.82 45/50
60 GPM LRHC – XHN T - 17A 1.81 1 1/4” 1.81 3.27 150/160
120 GPM LRJC – XHN T - 19A 2.50 1 5/8” 2.31 3.94 350/375

■ Control orifice diameter = LRB*, LRD*, LRF*: .016 in., LRH*, LRJ*: .021 in.

LR ✱ ✱ – ✱✱✱
Nominal Version Control** Control Pressure Seal
Capacity
B 7.5 GPM $ 41.00 A Internal pilot Port 1 +$ 3.70 X Non-adjustable +$ 0.00 D 50 psi +$ 0.00 N Buna-N
to Port 3 (mainstage
D 15 GPM $ 41.00 relief element) F 100 psi +$ 0.00 V Viton
F 30 GPM $ 54.40 C External pilot +$ 0.00 Available in D G*150 psi

(bypass compensator) Adjustment Range only
H 60 GPM $ 100.50 H 200 psi
L Tuning Adjustment
J 120 GPM $ 189.60 + 25% of customer
specified flow
* G Adjustment Range
** See page 162 for information not available in
on Control Options LRBA, LRBC.
Logic Elements
NORMALLY OPEN, DIRECT OPERATED
2
b
4 3
4 c
Drain
1
3
Pilot Locating
a Model Code (lb. ft.)
2 15 GPM DODS – XHN T - 21A 1.38 7/8” 1.78 30/35
Port 30 GPM DOFS – XHN T - 22A 1.38 1 1/8” 2.00 45/50
60 GPM DOHS – XHN T - 23A 1.81 1 1/4” 2.47 150/160
Port 1
120 GPM DOJS – XHN T - 24A 2.50 1 5/8” 3.16 350/375
Performance Curves
DODS DOFS DOHS DOJS
Fully Open Pressure Differential vs. Flow
300 300 300 300
250 250 250 250
P = psi
P = psi
P = psi
P = psi
200 200 200 200
150 150 150 150
100 100 100 100
50 50 50 50
0 3.75 7.5 11.25 15 0 7.5 15 22.5 30 0 15 30 45 60 0 30 60 90 120

■ Maximum operating pressure = 5000 psi (Port 1 and Port 2)

■ Minimum pilot pressure to shift valve = DODS: 400 psi, DOFS, DOHS, DOJS: 300 psi
■ Maximum valve leakage, Port 1 to Port 2 or Port 2 to Port 1 = 5 drops/min.
■ Pilot volume for complete shift = DODS: .01 in³/min., DOFS: .02 in³/min., DOHS: .05 in³/min.,
DOJS: .17 in³/min.
■ Valve will open when the pilot pressure falls below 145 psi.
■ Any back pressure at the drain port is directly additive to the required pilot pressure for reliable
operation.

DO ✱ S – ✱ H ✱
Nominal
Capacity Control** Control Pressure Seal
D 15 GPM $ 65.00 X Non-adjustable +$ 0.00 H 200 psi +$ 0.00 N Buna-N
F 30 GPM $ 88.00 V Viton
H 60 GPM
J 120 GPM

on Control Options
Logic Elements
NORMALLY OPEN, VENT-TO-OPERATE
2
b
4 3
4 c
Vent
1
3
Locating
Pilot Shoulder
a Nominal Cartridge Cavity a b c Torque
Capacity Model Code (lb. ft.)
2
Port 15 GPM DODR – XHN T - 21A 1.38 7/8” 1.78 30/35
30 GPM DOFR – XHN T - 22A 1.38 1 1/8” 2.00 45/50
Port 1 60 GPM DOHR – XHN T - 23A 1.81 1 1/4” 2.47 150/160
120 GPM DOJR – XHN T - 24A 2.50 1 5/8” 3.16 350/375
Performance Curves
DODR DOFR DOHR DOJR
300 300 300 300
250 250 250 250
P = psi
P = psi
P = psi
P = psi
200 200 200 200

150 150 150 150
100 100 100 100
50 50 50 50
0 3.75 7.5 11.25 15 0 7.5 15 22.5 30 0 15 30 45 60 0 30 60 90 120


■ Minimum pilot pressure to shift valve with Port 4 vented to tank = DODR: 400 psi,
DOFR, DOHR, DOJR: 300 psi
■ Control pilot flow = DODR: 25 in³/min., DOFR: 22 in³/min., DOHR, DOJR: 35 in³/min.
■ Valve will open when the pilot pressure falls below 145 psi or with Port 4 blocked.
■ Port 4 may be externally connected to a pilot switching valve. The pilot valve should have a leakage rate
of less than 10 drops/min. and be able to satisfy the pilot flow requirements. Sun model DAAA-***
solenoid pilot valve is ideal for this application.

DO ✱ R – ✱ ✱ ✱
Nominal
Control** Control Pressure Seal
Capacity
H 60 GPM
J 120 GPM

on Control Options
Logic Elements
NORMALLY OPEN, VENT-TO-OPERATE WITH INTEGRAL PILOT CONTROL
CAVITY
2
The -8 control option allows a pilot control valve to be incorporated
directly into the end of the cartridge via the T-8A cavity. These pilot
T-8A control cartridges are sold separately and include solenoid, air pilot,
b Cav 3
and hydraulic pilot operation. See Pilot Control Cartridges on page 121.
c 4 1
4
Drain
3
Pilot Locating Cartridge Dimensions
Nominal Cartridge Cavity a b c Torque
Capacity Model Code (lb. ft.)
a
2 15 GPM DODR – 8HN T - 21A 1.38 7/8” 1.78 30/35
Port 30 GPM DOFR – 8HN T - 22A 1.38 1 1/8” 2.00 45/50
60 GPM DOHR – 8HN T - 23A 1.81 1 1/4” 2.47 150/160
1 Port
120 GPM DOJR – 8HN T - 24A 2.50 1 5/8” 3.16 350/375
Performance Curves
DODR-8 DOFR-8 DOHR-8 DOJR-8
300 300 300 300
250 250 250 250
P = psi
P = psi
P = psi
P = psi
200 200 200 200

150 150 150 150
100 100 100 100
50 50 50 50
0 3.75 7.5 11.25 15 0 7.5 15 22.5 30 0 15 30 45 60 0 30 60 90 120


■ Minimum pilot pressure to shift valve = DODR: 400 psi, DOFR, DOHR, DOJR: 300 psi
■ Control pilot flow = DODR: 25 in³/min., DOFR: 22 in³/min., DOHR, DOJR: 35 in³/min.
■ Any back pressure at the drain port is directly additive to the required pilot pressure.

DO ✱ R – 8 ✱ ✱
Nominal Control** Control Pressure Seal
Capacity
D 15 GPM $ 65.00 8 with T-8A cavity +$ 4.00 H 200 psi +$ 0.00 N Buna-N
in hex body for
(see pilot control
H 60 GPM $147.00 section for alternate
options)
J 120 GPM

on Control Options
Logic Elements
NORMALLY OPEN, PRESSURE ADJUSTABLE

+ -
b
c 4 1
4
Drain Cartridge Dimensions
3 Locating
Nominal Cartridge a b Torque
Pilot Shoulder
Capacity Model Code Cavity L C K (lb. ft.)
15 GPM DODP – LAN T - 21A 1.38 7/8” 3.11 3.15 3.35 30/35
a 30 GPM DOFP – LAN T - 22A 1.38 1 1/8” 3.43 3.50 3.70 45/50
2
Port 60 GPM DOHP – LAN T - 23A 1.81 1 1/4” 3.94 3.98 4.17 150/160
120 GPM DOJP – LAN T - 24A 2.50 1 5/8” 4.76 4.92 5.04 350/375
Port 1
Performance Curves
DODP DOFP DOHP DOJP

300 300 300 300
250 250 250 250
P = psi
P = psi
P = psi
P = psi
200 200 200 200

150 150 150 150
100 100 100 100
50 50 50 50
0 3.75 7.5 11.25 15 0 7.5 15 22.5 30 0 15 30 45 60 0 30 60 90 120


■ Minimum pilot pressure to shift valve = DODP: 400 psi, DOFP, DOH, DOJP: 300 psi
■ Control pilot flow at shift = DODP, DOFP: 24 in³/min., DOHP, DOJP: 36 in³/min.
■ Valve will open when the pilot pressure drops 85% below setting.

DO ✱ P – ✱ ✱ ✱
Nominal Base Nominal Adjustable
Capacity Price Control** Shift Pressure Range Seal
H 60 GPM $152.10 K Handknob +$ 6.00 W 300 - 4500 psi
J 120 GPM

Logic Elements
NORMALLY CLOSED, DIRECT OPERATED
2
b
4 3
4 c
Drain 1
3
Pilot Locating
2 15 GPM DKDS – XHN T - 21A 1.38 7/8” 1.78 30/35
Port
30 GPM DKFS – XHN T - 22A 1.38 1 1/8” 2.00 45/50
60 GPM DKHS – XHN T - 23A 1.81 1 1/4” 2.47 150/160
Port 1
120 GPM DKJS – XHN T - 24A 2.50 1 5/8” 3.16 350/375
Performance Curves
DKDS DKFS DKHS DKJS
Pilot Open Pressure Drop
300 300 300 300
250 250 250 Flow from 250 Flow from
Port 2 to Port 1 Port 2 to Port 1
P = psi
P = psi
P = psi
P = psi
200 200 200 200
Flow from Flow from
150 150 150 150 Port 1 to Port 2
Port 1 to Port 2
100 100 100 100
50 50 50 50
0 3.75 7.5 11.25 15 0 7.5 15 22.5 30 0 15 30 45 60 0 30 60 90 120


■ Minimum pilot pressure to shift valve = DKDS: 400 psi, DKFS, DKHS, DKJS: 300 psi
■ Pilot volume for complete shift = DKDS: .01 in³/min., DKFS: .02 in³/min., DKHS: .05 in³/min.,
DKJS: .17 in³/min.
■ Valve will reseat when the pilot pressure drops 85% below setting.

DK ✱ S – ✱ ✱ ✱
Nominal
Capacity
H 60 GPM
J 120 GPM

on Control Options
Logic Elements
NORMALLY CLOSED, PRESSURE ADJUSTABLE

+ -
b
c 4 1
4
Drain Cartridge Dimensions
3 Nominal Typical c Installation
Locating Cartridge Cavity a b Torque
Pilot Shoulder Capacity Model Code L C K (lb. ft.)
15 GPM DKDP – LAN T - 21A 1.38 7/8” 3.11 3.16 3.34 30/35
a 30 GPM DKFP – LAN T - 22A 1.38 1 1/8” 3.44 3.50 3.70 45/50
2
Port 60 GPM DKHP – LAN T - 23A 1.81 1 1/4” 3.94 3.98 4.17 150/160
120 GPM DKJP – LAN T - 24A 2.50 1 5/8” 4.78 4.92 5.04 350/375
Port 1
Performance Curves
DKDP DKFP DKHP DKJP

Piloted Open Pressure Drop
300 300 300 300
250 250 250 250
P = psi
P = psi
P = psi
P = psi
200 200 200 200
150 150 150 150
100 100 100 100
50 50 50 50
0 3.75 7.5 11.25 15 0 7.5 15 22.5 30 0 15 30 45 60 0 30 60 90 120


■ Minimum pilot pressure to shift valve = DKDP: 400 psi, DKFP, DKHP, DKJP: 300 psi
■ Control pilot flow at shift = DKDP, DKFP: 24 in³/min., DKHP, DKJP: 36 in³/min.
■ Valve will reseat when the pilot pressure falls to 85% of the cracking value.

DK ✱ P – ✱ ✱ ✱
Nominal Base Nominal Adjustable
Capacity Price Control** Shift Pressure Range Seal
H 60 GPM $152.10 K Handknob +$ 6.00 W 300 - 4500 psi
J 120 GPM

** See page 162 for information A, B, and W are standard set at 1000 psi.
Logic Elements
NORMALLY CLOSED, VENT-TO-OPERATE
b
4 3
4 c
Vent 1
3
Locating
Pilot Shoulder
a
Port Nominal Typical Installation
Port 1
15 GPM DKDR – XHN T - 21A 1.38 7/8” 1.78 30/35
30 GPM DKFR – XHN T - 22A 1.38 1 1/8” 2.00 45/50
60 GPM DKHR – XHN T - 23A 1.81 1 1/4” 2.47 150/160
120 GPM DKJR – XHN T - 24A 2.50 1 5/8” 3.16 350/375
Performance Curves
DKDR DKFR DKHR DKJR
300 300 300 300
250 250 250 250
P = psi
P = psi
P = psi
P = psi
200 200 200 200

150 150 150 150
100 100 100 100
50 50 50 50
0 3.75 7.5 11.25 15 0 7.5 15 22.5 30 0 15 30 45 60 0 30 60 90 120


■ Minimum pilot pressure to shift valve with Port 4 vented to tank = DKDR: 400 psi,
DKFR, DKHR, DKJR: 300 psi
■ Control pilot flow = DKDR: 25 in³/min., DKFR: 22 in³/min., DKHR, DKJR: 35 in³/min.
■ Valve will reseat when the pilot pressure falls below 145 psi.
■ Port 4 may be externally connected to a pilot switching valve. The pilot valve should have a leakage
rate of less than 10 drops/min. and be able to satisfy the pilot flow requirements. Sun model DAAA-***
solenoid pilot valve is ideal for this application.

DK ✱ R – ✱ ✱ ✱
Nominal Control** Nominal Shift Pressure Seal
Capacity
D 15 GPM $ 64.00 X Non-adjustable +$ 0.00 H 200 psi +$ 0.00 N Buna-N +$ 0.00
F 30 GPM $ 86.00 V Viton +$ 4.00
H 60 GPM
J 120 GPM

on Control Options
Logic Elements
NORMALLY CLOSED, VENT-TO-OPERATE WITH INTEGRAL
2
into the end of the cartridge via the T-8A cavity. These pilot control
T-8A
b Cav 3 pilot, and hydraulic pilot operation. See Pilot Control Cartridges on page 121.
4 c 4 1
Drain
3
Pilot Locating
Shoulder
2 a 15 GPM DKDR – 8H* T - 21A 1.38 7/8” 1.78 30/35
Valve
30 GPM DKFR – 8H* T - 22A 1.38 1 1/8” 2.00 45/50
60 GPM DKHR – 8H* T - 23A 1.81 1 1/4” 2.47 150/160
1 Valve
120 GPM DKJR – 8H* T - 24A 2.50 1 5/8” 3.16 350/375
Performance Curves
DKDR-8 DKFR-8 DKHR-8 DKJR-8
300 300 300 300
250 250 250 250
P = psi
P = psi
P = psi
P = psi
200 200 200 200

150 150 150 150
100 100 100 100
50 50 50 50
0 3.75 7.5 11.25 15 0 7.5 15 22.5 30 0 15 30 45 60 0 30 60 90 120


■ Minimum pilot pressure to shift valve with Port 4 vented to tank = DKDR: 400 psi,
DKFR, DKHR, DKJR: 300 psi
■ Control pilot flow = DKDR: 25 in³/min., DKFR: 22 in³/min., DKHR, DKJR: 35 in³/min.
■ Any back pressure at the drain port is directly additive to the required pilot pressure for reliable
operation.

DK ✱ R – 8 ✱ ✱
Nominal
Control** Nominal Shift Pressure Seal
Capacity
D 15 GPM $ 64.00 8 with T-8A cavity +$ 4.00 H 200 psi +$ 0.00 N Buna-N
in hex body for
(see pilot control
H 60 GPM $143.00 section for alternate
options)
J 120 GPM

on Control Options
Directional Cartridge Valves
Cartridge Type Page

2
2-position, 2-way and 3-way, with Internal

102
Drain
1 3
2 4
2–position, 2-way and 3-way, with External

103
Drain
1 3
2-position, 2-way and 3-way Direct Acting,

104
with Internal Drain
1 3
2 3
1 2-position, 2-way and 3-way, Direct Acting 105
3-port, 2-way and 3-way with Integral Pilot

T-8A 106
Control Cavity
3 1
4 2
4-port, 2-way and 3-way with Integral Pilot

T-8A 107
Control Cavity
1 3
2-position, 2-way Poppet, Control 1 to 2 with

T-8A
108
1
T-8A 2-position, 2-way Poppet, Control 2 to 1 with

109
1
(A) 2 4 (B)
(X) 6 5 (Y) 3-position, 4-way Spring Centered 110

(P) 3 1 (T)
(A) 2 4 (B)
(X) 6 5 (Y)
2-position, 4-way Detented 111
(P) 3 1 (T)

Directional Valves
2 POSITION, 2-WAY AND 3-WAY, WITH INTERNAL DRAIN
2 2 2 2
+ -
1 3 1 3 1 3 1 3
b c
DP*A DP*B DP*C DP*D
Port
Locating Model Code L C K (lb. ft.)
Shoulder
7.0 GPM DPBA – LAN T - 11A 1.38 7/8” 2.50 2.56 2.75 30/35
a 15 GPM DPCA – LAN T - 2A 1.38 1 1/8” 2.81 2.88 3.06 45/50
2
Port
Port 1
Performance Curves
DPB* DPC*
Typical Pilot Oil Flow vs. Load Typical Pilot Oil Flow vs. Load
Pressure Drop Pressure above Valve Setting Pressure Drop Pressure above Valve Setting
400 .30 400 .30
Flow = GPM
Flow = GPM
300 300
P = psi
P = psi
.20 .20
200 200
.10 .10
100 100
0 2 4 6 8 10 0 1000 2000 3000 4000 5000 0 5 10 15 20 0 1000 2000 3000 4000 5000
Flow = GPM P = psi Flow = GPM P = psi

■ Control pilot flow at opening = DPBA, DPBB, DPBC, DPBD = 7 - 10 in³/min., DPCA, DPCB, DPCC,
DPCD = 10 - 15 in³/min.
■ Pressure at port 3 is directly additive to the setting of the valve. Because of this, port 3 may not be
useable as a work port in your circuit. If this is a consideration, the 4 port version of this valve may
be a solution.
■ For DP*C and DP*D port 3 can be blocked to prevent the cartridge from shifting.

DP ✱ ✱ – ✱✱✱
Nominal Version Control** Adjustment Range Seal
Capacity
B 7.0 GPM $ 60.50 A 2 Position 2-Way +$ 0.00 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N
Normally Open
C 15 GPM $ 73.40 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton
B 2 Position 2-Way
Normally Closed K Handknob +$ 6.00 D 25 - 800 psi
C 2 Position 3-Way +$ 8.00 E 25 - 400 psi

Port 1 Blocked
W 150 - 4500 psi
D 2 Position 3-Way
Port 1 Open

Directional Valves
2 POSITION, 2-WAY AND 3-WAY, WITH EXTERNAL DRAIN
Full Adjustment 5 Turns 2 4 2 4 2 4 2 4
+ -
b 1 3 1 3 1 3 1 3
c DP*M DP*N DP*O DP*P
4
Port Capacity Cartridge Cavity a b Torque
3 Locating
Port Shoulder 7.0 GPM DPBM – LAN T - 21A 1.38 7/8” 3.09 3.15 3.34 30/35
15 GPM DPCM – LAN T - 22A 1.38 1 1/8” 3.44 3.50 3.69 45/50
a
2
Port
Port 1
Performance Curves
DPB* DPC*
Typical Pilot Oil Flow vs. Load Typical Pilot Oil Flow vs. Load
Pressure Drop Pressure above Valve Setting Pressure Drop Pressure above Valve Setting
400 .30 400 .30
Flow = GPM
300 300
Flow = GPM
P = psi
P = psi
.20 .20
200 200
.10 .10
100 100
0 2 4 6 8 10 0 1000 2000 3000 4000 5000 0 5 10 15 20 0 1000 2000 3000 4000 5000
Flow = GPM P = psi Flow = GPM P = psi

■ Control pilot flow at opening = DPBM, DPBN, DPBO, DPBP = 7 - 10 in³/min., DPCM, DPCN, DPCO,
DPCP = 10 - 15 in³/min.
■ Pressure at port 4 is directly additive to the setting of the valve.
■ Port 3 can be used as a work port.
■ Port 4 can be blocked to prevent the cartridge from shifting.

DP ✱ ✱ – ✱✱✱
Nominal
Version Control** Adjustment Range Seal
Capacity
B 7.0 GPM $ 76.70 M 2 Position 2-Way +$ 0.00 L Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
Normally Open
C 15 GPM $ 97.60 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 V Viton
N 2 Position 2-Way
O 2 Position 3-Way +$ 8.00 E 25 - 400 psi

Port 1 Blocked
W 150 - 4500 psi
P 2 Position 3-Way
Port 1 Open

Directional Valves
2 POSITION, 2-WAY AND 3-WAY DIRECT ACTING, INTERNAL DRAIN
2 2 2 2
+ -
1 3 1 3 1 3 1 3
c
b DRBA DRBB DRBC DRBD
Locating Model Code L C K (lb. ft.)
Port Shoulder
7.0 GPM DRBA – LAN T - 11A 1.38 7/8” 3.10 3.16 3.34 30/35
a
2
Port
Port 1
Performance Curves
DRBA DRBB DRBC DRBD

Port 1 to Port 2
400 Port 2 400 400 Port 2 400
to Port 3 Port 2 to Port 3
to Port 3 Port 2
300 300 300 300
P = psi
P = psi
P = psi
P = psi
to Port 3
200 200 200 200

Port 1
100 100 100 to Port 2 100
0 2 4 6 8 10 12 14 0 2 4 6 8 10 12 14 0 2 4 6 8 10 12 14 0 2 4 6 8 10 12 14

■ Pressure at port 3 is directly additive to the setting of the valve. Because of this, port 3 may not be
useable as a work port in your circuit. If this is a consideration, the 4 port version of this valve may
be a solution.

DR ✱ ✱ – ✱✱✱
Capacity
B 7.0 GPM $ 60.50 A 2 Position 2-Way +$ 0.00 L Standard Screw +$ 0.00 A 500 - 3000 psi +$ 0.00 N Buna-N
Normally Open
C Tamper Resistant +$ 4.10 B 200 - 1500 psi +$ 0.00 V Viton
B 2 Position 2-Way
C 2 Position 3-Way +$ 8.00 E 30 - 400 psi

Port 1 Blocked
S 30 - 200 psi
D 2 Position 3-Way
Port 1 Open W 750 - 4500 psi

** See page 162 for information E and S are standard set at 200 psi.
Directional Valves
2-POSITION, 2-WAY AND 3 WAY, DIRECT ACTING
+ - 2 4 2 4 2 4 2 4 2 3
b
c 1 3 1 3 1 3 1 3 4
DRBM DRBN DRBO DRBP DRBR
External Drain External Drain External Drain External Drain External Pilot
4
Port Cartridge Dimensions
Port Locating
Shoulder
7.0 GPM DRBM – LAN T - 21A 1.38 7/8” 3.10 3.16 3.34 30/35
2 a 7.0 GPM DRBN – LAN T - 21A 1.38 7/8” 3.10 3.16 3.34 30/35
Port 7.0 GPM DRBO – LAN T - 21A 1.38 7/8” 3.10 3.16 3.34 30/35
7.0 GPM DRBP – LAN T - 21A 1.38 7/8” 3.10 3.16 3.34 30/35
1 Port
7.0 GPM DRBR – LAN T - 21A 1.38 7/8” 3.10 3.16 3.34 30/35
Performance Curves
DRBM DRBN DRBO DRBP DRBR
Port 1 to Port 2 Port 1 to Port 2 Port 1 to Port 2
400 Port 2 400 400 Port 2 400 400
to Port 2 to Port 2 Port 2
Port 3 Port 3 300
P = psi
300 300 300 300 to
P = psi
P = psi
P = psi
P = psi
to to
Port 3 Port 3 Port 3
200 200 200 200 200
Port 1 Port 1
100 to 100 100 to 100 100
Port 2 Port 2
0 2 4 6 8 10 12 14 0 2 4 6 8 10 12 14 0 2 4 6 8 10 12 14 0 2 4 6 8 10 12 14 0 2 4 6 8 10 12 14

■ DRBM, DRBN, DRBO, DRBP: Port 3 can be used as a work port
■ DRBM, DRBN, DRBO, DRBP: Pressure at port 4 is directly additive to the setting of the valve.

DR ✱ ✱ – ✱✱✱
Nominal Base
Version Control** Adjustment Range Seal
Capacity Price
B 7.0 GPM $ 84.50 M 2-Position, 2-Way, -$ 7.20 L Standard Screw +$ 0.00 A 500 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
Normally Open,
External Drain C Tamper Resistant +$ 4.10 B 200 - 1500 psi +$ 0.00 V Viton +$ 3.00
N 2-Position, 2-Way, -$ 7.20 K Handknob +$ 6.00 N* 30 - 800 psi +$ 1.00

Normally Closed,
External Drain E* 30 - 400 psi +$ 1.00
O 2-Position, 3-Way, -$ .20 S* 30 - 200 psi +$ 2.00

Port 1 Blocked,
External Drain W 750 - 4500 psi +$ 0.00
P 2-Position, 3-Way, +$ 2.00

Port 1 Open, * DRBR only available with
External Drain these spring ranges.
R 2-Position, 3-Way, +$ 3.80

External Pilot*

** See page 162 for information E and S are standard set at 200 psi.
Directional Valves
2-WAY AND 3-WAY WITH INTEGRAL PILOT CONTROL CAVITY
2 2
The -8 control option allows the pilot
2 2
control valve to be incorporated directly
into the end of the cartridge via
b T-8A T-8A T-8A T-8A
cartridges are sold separately and
include solenoid, air pilot, and hydraulic
c 3 1 pilot operation. See Pilot Control Cartridges
1 3 1 3 1 3
on page 121.
3
Port Locating DVBA-8 DVBB-8 DVBC-8 DVBD-8
Shoulder
2 Model Code (lb. ft.)
Port 7 GPM DVBA-8FN T-11A 1.38 7/8 1.38 30/35
7 GPM DVBB-8FN T-11A 1.38 7/8 1.38 30/35
1 Port 7 GPM DVBC-8FN T-11A 1.38 7/8 1.38 30/35
7 GPM DVBD-8FN T-11A 1.38 7/8 1.38 30/35
Performance Curves
DV✱✱-8
400
300
P = psi
200
100
0 2 4 6 8 10
Flow = GPM

■ Control pilot flow at opening = DVBA-8, DVBB-8, DVBC-8, DVBD-8 = 7 - 10 in³/min., DVCA-8,
DVCB-8, DVCC-8, DVCD-8 = 10 - 15 in³/min.
■ Maximum leakage per path = 2 in³/min. at 1000 psi
■ There must be a pressure source at port 1, relative to port 3, to shift the valve.
■ Pressure at port 3 may oppose the opening of the valve. Because of this, port 3 may not be useable as a
work port in your circuit. If this is a consideration, the 4 port version of this valve may be a solution.

DV ✱ ✱ – 8 ✱✱
Capacity
B 7GPM $ 58.90 A 2 Position, 2-Way +$ 0.00 8 T-8A Cavity in +$ 0.00 F 100 psi +$ 0.00 N Buna-N
Normally Open in hex body for
pilot operation V Viton
B 2 Position, 2-Way +$0.00 (Pilot valve to
Normally Closed be ordered
separately)
C 2 Position, 3-Way,
Port 1 Blocked
D 2 Position, 3-Way,
Port 1 Open

on Control Options
Directional Valves
4-PORT, 2-WAY AND 3-WAY WITH INTEGRAL PILOT CONTROL CAVITY
The -8 control option allows the pilot
4 2 2 4 2 4 2 4
control valve to be incorporated directly
b into the end of the cartridge via
T-8A T-8A T-8A T-8A
cartridges are sold separately and
include solenoid, air pilot, and hydraulic
c 1 3
pilot operation. See Pilot Control Cartridges
4 1 3 1 3 1 3
Port on page 121.
DVBM-8 DVBN-8 DVBO-8 DVBP-8

3
Port Locating Cartridge Dimensions
Shoulder
a 7 GPM DVBM – 8FN T-21A 1.38 7/8 1.69 30/35
2
Port 7 GPM DVBN – 8FN T-21A 1.38 7/8 1.69 30/35
7 GPM DVBO – 8FN T-21A 1.38 7/8 1.69 30/35
1 Port 7 GPM DVBP – 8FN T-21A 1.38 7/8 1.69 30/35
Performance Curves
DV✱✱-8
400
300
P = psi
200
100
0 2 4 6 8 10
Flow = GPM

■ Control pilot flow at opening = DVBM-8, DVBN-8, DVBO-8, DVBP-8 = 7 - 10 in³/min., DVCM-8,
DVCN-8, DVCO-8, DVCP-8 = 10 - 15 in³/min.

DV ✱ ✱ – 8 ✱✱
Capacity
B 7 GPM $ 74.60 M 2 Position, 2-Way +$ 0.00 8 T-8A Cavity in +$ 0.00 F 100 psi +$ 0.00 N Buna-N
Normally Open hex body for
N 2 Position, 2-Way +$ 0.00 (Pilot valve to
Normally Closed be ordered
separately)
O 2 Position, 3-Way,
Port 1 Blocked
P 2 Position, 3-Way,
Port 1 Open

on Control Options
2-POSITION, 2-WAY POPPET, CONTROL 1 TO 2 WITH INTEGRAL
2
The -8 control option allows the pilot control valve to be incorporated directly
b into the end of the cartridge via the T-8A cavity. These pilot control
c T-8A
cartridges are sold separately and include solenoid, air pilot, and hydraulic
pilot operation. See Pilot Control Cartridges on page 121.
Locating
Shoulder
1
Port 15 GPM DFCA – 8DN T - 13A 1.38 7/8 .75 30/35
30 GPM DFDA – 8DN T - 5A 1.62 1 1/8 .69 45/50
60 GPM DFEA – 8DN T - 16A 2.44 1 1/4 .97 150/160
Port 1
120 GPM DFFA – 8DN T - 18A 3.13 1 5/8 1.19 350/375
Performance Curves
DFCA-8 DFDA-8 DFEA-8 DFFA-8
250 250 100 100
200 200
75 75
P = psi
P = psi
P = psi
P = psi
150 150
50 50
100 100
50 50 25 25
0 5 10 15 20 25 0 10 20 30 40 50 0 10 20 30 40 50 60 0 20 40 60 80 100 120

■ Main stage leakage less than 5 drops/min.

DF ✱ A – 8 D ✱
Capacity
C 15 GPM $ 29.30 8 T-8A cavity in hex body + 0.00 D 50 psi + 0.00 N Buna-N
for pilot operation (Pilot
D 30 GPM $ 47.00 valve to be ordered separately) V Viton
Options are:
E 60 GPM $ 79.50 • Solenoid Pilot
• Air Pilot
F 120 GPM $ 140.90 • Hydraulic Pilot
• Manual Control
Directional Valves
2-POSITION, 2-WAY POPPET, CONTROL 2 TO 1 WITH INTEGRAL
into the end of the cartridge via the T-8A cavity. These pilot control
T-8A
c
Locating
Shoulder
1
Port Capacity Cartridge Cavity a b c Torque
15 GPM DFCB – 8DN T - 13A 1.38 7/8” .75 30/35
Port 1 30 GPM DFDB – 8DN T - 5A 1.62 1 1/8” .69 45/50
60 GPM DFEB – 8DN T - 16A 2.44 1 1/4” .97 150/160
Performance Curves
DFCB-8 DFDB-8 DFEB-8

250 250 100
200 200
75
P = psi
P = psi
P = psi
150 150
50
100 100
50 50 25
0 5 10 15 20 25 0 10 20 30 40 50 0 10 20 30 40 50 60

■ Main stage leakage less than 5 drops/min.

DF ✱ B – 8 D ✱
Nominal
Capacity Control Adjustment Range Seal
C 15 GPM $ 35.00 T-8A Pilot Cavity +$ 0.00 D Bias Spring +$ 0.00 N Buna-N
Pilot Stage Control 50 psi
D 30 GPM $ 52.90 to be ordered V Viton
separately.
E 60 GPM $ 85.50 Options are:
• Solenoid Pilot
• Air Pilot
• Hydraulic Pilot
• Manual Control
Directional Valves
3-POSITION, 4-WAY SPRING CENTERED
(A) 2 4 (B)
b
c
6 (X) 6 5 (Y)
Port
5
Port Locating (P) 3 1 (T)
Shoulder
Port Typical Installation
3
Port 10 GPM DCCC – XCN T - 61A 3.35 7/8” 1.97 30/35
20 GPM DCDC – XCN T - 62A 3.63 1 1/8” 2.31 45/50
2
Port 40 GPM DCEC – XCN T - 63A 4.51 1 1/4” 2.84 150/160
80 GPM DCFC – XCN T - 64A 5.51 1 5/8” 3.59 350/375
Port 1
Performance Curves
DCCC DCDC DCEC DCFC
400 400 400 400
P to T P to T P to T
300 300 P to A or B 300 300
P = psi
P = psi
P = psi
P = psi
P to A or B P to A or B All Flow Paths
B to T B to T Except A to T
100 100 A to B Regen 100 B to T 100
A to B Regen
A to T A to T A to T A to T
200 200 200 200
0 2 4 6 8 10 12 0 5 10 15 20 25 30 0 10 20 30 40 50 60 0 20 40 60 80 100 120

■ Pilot volume for complete shift = DCCC: .02 in³/min., DCDC: .06 in³/min., DCEC: .17 in³/min.,
DCFC: .42 in³/min.
■ Minimum pilot pressure required to shift valve = DCCC: 175 psi, DCDC: 150 psi, DCEC, DCFC: 125 psi
■ All ports will accept 5000 psi, including the x and y pilot ports (port 5 and port 6).

DC ✱ C – X✱✱
Nominal Base Spool Configuration
Seal
Capacity Price Capacity (GPM)
C 10 GPM $ 95.90 C D E F N Buna-N
D 20 GPM $ 129.30 C 10+ 30+ 100+ 200+ +$ 0.00 V Viton
E 40 GPM $ 196.10 T 10 24 40 100
F 80 GPM $ 350.30 H 10 25 40 100
Y 10 30+ 100+ 200+
W 10+ 30+ 100 200
R 7.0 11 25 50
N 7.0 12 25 50
X 7.0 15 30 60
B 10 30+ 75 150
Typical switching pilot pressure A 10 30+ 75 150

differential between pilot
ports 5 and 6 is 200 psi.
Directional Valves
2-POSITION, 4-WAY DETENTED
(A) 2 4 (B)
b
c (X) (Y)
6 6 5
Port
5 Locating
Port Shoulder (P) 3 1 (T)
3
Port 10 GPM DCCD – XCN T - 61A 3.35 7/8” 1.97 30/35
20 GPM DCDD – XCN T - 62A 3.63 1 1/8” 2.31 45/50
2
Port 40 GPM DCED – XCN T - 63A 4.51 1 1/4” 2.84 150/160
80 GPM DCFD – XCN T - 64A 5.51 1 5/8” 3.59 350/375
Port 1
Performance Curves
DCCD DCDD DCED DCFD
400 400 400 400
300 300 P to A or B 300 300

P = psi
P = psi
P = psi
P = psi
P to A or B P to A or B All Flow Paths
B to T Except A to T
100 B to T 100 100 B to T 100
A to T A to T A to T A to T
200 200 200 200
0 2 4 6 8 10 12 0 5 10 15 20 25 30 0 10 20 30 40 50 60 0 20 40 60 80 100 120

■ Pilot volume for complete shift = DCCD: .05 in³/min., DCDD: .12 in³/min., DCED: .34 in³/min.,
DCFD: .84 in³/min.
■ Minimum pilot pressure required to shift valve = 40 psi
■ All ports will accept 5000 psi, including the x and y pilot ports (port 5 and port 6).

DC ✱ D – X✱✱
Nominal Base Spool Configuration
Seal
Capacity Capacity (GPM)
C 10 GPM $ 95.90 C D E F N Buna-N
D 20 GPM $ 129.30 C 11 22 45 90 +$ 0.00 V Viton
E 40 GPM $ 196.10 H 10 20 40 80
F 80 GPM $ 350.30 X 13 30+ 60+ 120+
Typical switching pilot pressure

differential between pilot
ports 5 and 6 is 200 psi.
Directional Valves
NOTES

Solenoid Operated
Cartridge Valves
Cartridge Type Page
Normally Open Normally Closed
2 2
2-position, 2-way Spool Directional Valve 114
1 1
2
2 Direct Acting, 2-position, 2-way Poppet
Directional Valve 115
1 1
2 2
1 3 3
1
Normally Closed
2 4
3 1

2 2
2-position, 2-way Spool Directional
Valve – Pilot Capacity 118
1 1
Normally Open 1-3 Normally Open 1-2

1 1
2-position, 3-way Spool Directional

Valve – Pilot Capacity 119
2 3 2 3

Relief Valves
PILOT OPERATED,
Solenoid Operated CartridgeBALANCED
Valves PISTON
2-POSITION,
Full Adjustment 5 Turns 2-WAY SPOOL DIRECTIONAL VALVE
+ -
Normally
d 2 Closed
2 2
1
c
1
b
Normally
c Locating Open 1
Shoulder
Cartridge
CartridgeDimensions
Dimensions
Typical Typical c Installation
Installation
Nominal
Capacity CartridgeCartridge Cavity Cavity a a b b L c Torque
Torque d
Capacity Model Code
Model Code C K (lb. (lb.
ft.) ft.)
b a Locating
Shoulder
10 GPM RPCC DLDA
12 GPM – LAN – MHN T - 162A T - 13A
1.22 1.383/4” 7/8”2.11 3.51 2.17 1.47 2.31 30/3525/30
2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
a 50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
2
Port 100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
Port 1 200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Curves
Performance Curves
RPCC RPEC RPGC
DLDA-M** RPIC RPKC
Valve Performance Limits
Typical Performance
at 10% Undervoltage
5000 vs. Flow 5000
and Stabilized Coil Temp.
5000 5000 5000
4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
C (2 to 1)
3000 3000 3000 3000 3000
5000 200 C (2 to 1)
2000 2000 2000 2000 C (1 to 2) 2000
4000 150
P = psi
P = psi
1000 1000 1000 1000 1000

3000 H (1 to 2)
H (2 to 1) 100
2000 20 H (2 to 1)
0 5 10 15 20 25 0 10 30 40 50 0 20 40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
Flow = GPM Flow
1000 = GPM
H (1 to 2)
Flow = GPM 50 Flow = GPM Flow = GPM
C (1 to 2)
■ Maximum operating 0 2 4
pressure
6
Flow = GPM
8 10 12
= 5000 psi 0 2 4 6
Flow = GPM
8 10 12

■ Maximum operating pressure = 5000 psi**
■ Maximum Leakage at 150 SUS = 5 in³/min. at 3000 psi
■
■ Factory
Switching pressure
frequency settings
= 15000 established
cycles/hr at 4 GPM
Proper installation of solenoid valves requires an extra deep socket to clear the solenoid tube.
■ Sockets areleakage
Maximum available from Snap
= RPCC, RPEC: On tools (P/N SIML280)
2 in 3/min./1000 or Sun3Hydraulics
psi, RPGC: (P/Npsi,
in3/min./1000 998-100-006).
RPIC: 4
See
in 3/min./1000 psi, RPKC: 5 infor
www.sunhydraulics.com 3/min./1000
details. psi.
**For valves produced before January 1, 2004 (date code A041), the maximum operating pressure is 5000 psi at port 2 and 3600 psi at port 1.
■ RPCC
NOTE: Whileminimum setting
the valve will operate forwith
reliably allpressures
spring ranges
up to 5000 psi atisPort
751, psi
solenoid tube fatigue life is reduced.
D LRP
D A✱ –C ✱– ✱✱✱✱ –✱ ✱ ✱ ✱
Nominal
Nominal Price
Capacity Control Spool Configuration Coil Configuration*
D 10 GPM $ 45.50 M Manual +$5.00 H Normally Open +$ 0.00 ISO/DIN
C 12 GPM* $ 31.90 L Override
Standard Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N
212 12 VDC+$ 0.00
C Normally Closed+$ 0.00 224 24 VDC
X No Manual +$0.00 211 115 VAC
G 50 GPM $ 51.80 K Override
Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00 223 230 VAC
I 100 GPM $ 97.30 N 60 - 800

Sealpsi +$ 1.00 AMP® Junior Timer
612 12 VDC
K 200 GPM $187.00 Q 60 - 400 psi +$ 0.00
N Buna-N +$ 1.00 624 24 VDC
W 150 - 4500 psi+$ 2.00
V Viton +$ 0.00 Twin Lead
712 12 VDC
724 24 VDC
A, B, C, and W are standard set at 1000 psi. Deutsch
N Option is standard set at 400 psi. 912 12 VDC
Q Option is standard set at 200 psi. 924 24 VDC
** See page 162 for information * Minimum setting 75 psi on all ranges.948 48 VDC
on Control Options
Customer may specify pressure setting. +$ 1.10
Metri-Pack
Maximum Leakage (in.3/min. at 3000 psi 812 12 VDC
with 150 SUS oil) = 5 824 24 VDC
Power (Watts) = 22
Operating Voltage Tolerance = ± 10% * See page 167 for Solenoid Twin Spade
Typical response Time (ms) = 50 for detailed and complete Connector
Options on our full line of products.
524 24 VDC
Relief Valves
PILOT OPERATED,
Solenoid BALANCED
Operated Cartridge Valves PISTON
DIRECT ACTING,
+ -
2-POSITION, 2-WAY POPPET DIRECTIONAL VALVE
Normally
d 2
Closed
2 1
c 2
b
1
Locating Normally
c Shoulder Open 1
Typical Cartridge Dimensionsc Installation
Capacity Cartridge Typical Cavity a b Torque
Installation
Nominal Model Code L C K (lb. ft.)
b a 12 GPM Model Code
RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 (lb. 25/30
ft.)
Locating
2 RPEC – LAN – MHN
DTDA
Shoulder
10
25 GPM GPM T - 10A T - 13A
1.56 1.38
7/8” 7/8”2.00 3.51 2.06 1.47 2.25 30/35
30/35
Outlet
a 50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
2 100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Port Inlet 1
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Port 1
Performance Curves
Performance Curves
DTDA-M*N
Valve Performance Limits at 10% Undervoltage Typical Performance
5000 and Stabilized Coil Temperature 5000
5000
Pressure Differential vs. Flow
5000 5000
4000 4000 4000 4000
P = psi
4000
P = psi
P = psi
P = psi
P = psi
5000 5000 250 250

3000 DTDA-MCN 3000 3000 3000 3000
4000 4000 DTDA-MHN 200 200
1 to 2
P = psi
P = psi
P = psi
P = psi
2000 2000 2 to 12000 DTDA-MHN
2000 2000 DTDA-MCN
3000 3000 150 150
1000 1000 1000 1000 1000
2000 2000 100 100
5 100010DTDA-MCN 20 0 10 20 DTDA-MHN 0 40 80 120 160 50
200 0 80 160 240 320 400
0 15 25 1000 30 40 50 0 20 40 60 50 80 100
2 to 1
1 to 2
0 2 4 6 8 10 12 14 16 0 2 4 6 8 10 12 14 16 0 2 4 6 8 10 12 14 16 0 2 4 6 8 10 12 14 16
Flow =■ GPM Maximum operating Flow = GPM = 5000 psi
pressure Flow = GPM Flow = GPM
■ Maximum operating pressure = 5000 psi**
■
■ Back
Maximum pressure on theattank
Leakage 150port
SUS(port= 102)drops/min.
■■ Factory
Switching pressure
frequencysettings= 15000established
cycles/hr.at 4 GPM
■■ Proper installation
Typical response time of solenoid
10 ms. valves requires an extra deep socket to clear the solenoid tube.
■ Maximum leakage = RPCC,Snap
Sockets are available from RPEC: On 2tools (P/N SIML280)
in 3/min./1000 psi, RPGC:or Sun3 Hydraulics (P/N
in3/min./1000 998-100-006).
psi, RPIC: 4
See
www.sunhydraulics.com details. psi.
3/min./1000
**For valves produced before January 1, 2004 (date code A041), the maximum operating pressure is
■ RPCC
5000 psi atminimum setting
port 2 and 3600 psi at port 1.for allWhile
NOTE: spring ranges
the valve is reliably
will operate 75 psi with pressures
up to 5000 psi at Port 1, solenoid tube fatigue life is reduced.
D TRP
DA C ✱– ✱✱✱✱ –
✱– ✱ ✱✱✱
Nominal
Nominal
Capacity Price Control Spool Configuration Coil Configuration*
D C 12 GPM*
10 GPM $ 31.90
$ 59.10 L
M Manual Screw+$5.00
Standard +$ 0.00 H A Openpsi+$ +$
100 - 3000
Normally 0.000.00 N Buna-N ISO/DIN
+$ 0.00
Override 212 12 VDC
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 C B 50 - 1500
Normally psi
Closed+$ +$
0.000.00 V Viton
224 24 +$ VDC2.00
G 50 GPM $ 51.80 X
K No Manual
Handknob +$0.00
+$ 5.00 C 150 - 6000 psi +$ 2.00 211 115 VAC
Override 223 230 VAC
I 100 GPM $ 97.30 N 60 - 800 psi +$ 1.00
AMP® Junior Timer
K 200 GPM $187.00 Q 60 - 400Seal
psi +$ 1.00 612 12 VDC
624 24 VDC
N W 150 - 4500 psi
Buna-N +$ 0.00
Twin Lead
V Viton +$ 2.00 712 12 VDC
Adjustment Range Options: 724 24 VDC
N Option is standard set at 400 psi. Deutsch
948 48 VDC
Metri-Pack
812 12 VDC
824 24 VDC
Power (Watts) = 22
Operating Visit www.sunhydraulics.com
Voltage Tolerance = ± 10% for detailed and complete
* technical information
See page 167 on our full line of products.
for Solenoid Twin Spade
Typical response Time (ms) = 50 6
Connector Options 524 24 USVDC
Shortcut Catalogue #999-901-243
Relief Valves
PILOT OPERATED,
Solenoid BALANCED
Operated Cartridge Valves PISTON
2-POSITION,
Full Adjustment 5 Turns 3-WAY SPOOL DIRECTIONAL VALVE
+ -
Normally
d 2
Closed
2 1
c 2
b 1 3
Normally
Locating
c Shoulder Open 1 3
Capacity Typical Cavity
Nominal CartridgeCartridge a b Installation
Torque
b Capacity Model Code Cavity a b L c C Torque
(lb. ft.) d K
12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
3 10 GPM DMDA – MNN T - 11A 1.38 7/8” 4.26 1.47 30/35
2 Locating
25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Port Shoulder
Outlet
a 50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
2
100 GPM RPIC – LAN T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Port
Inlet 1
Port 1 200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
Performance
Performance Curves
Curves
RPCC RPEC RPGC
DMDA-MNN RPIC RPKC
Valve Performance Limits at 10% UndervoltageTypical Pressure Rise Typical Performance
5000
and Stabilized
5000 Coil Temperature 5000 5000 Pressure Differential vs. Flow
5000
Spool Option A 4000 Spool Option N
4000 Spool Option
4000 A Spool
4000 Option N
P = psi
4000
P = psi
P = psi
P = psi
P = psi
3000 5000 3000 5000 3000 200 3000 (3 to 2) 200 3000

(1 to 2) (1 to 2)
4000 4000 (3 to 2) & (2 to 3) (3 to 2)
2000 2000 2000 150 2000 150 2000 (2 to 1)
P = psi
P = psi
P = psi
P = psi
(1 to 2) & (2 to 3)
3000 (2 to 1) 3000
1000 1000 1000 100 1000 100 1000
(1 to 2)
2000 2000 & (2 to 1) (2 to 1)
(3 to 2) 0 40 80 120 160 200
0 1000 5 10 15 20 25 0 10 20 30 40 50 0 20 40 6050 80 100 50 0 80 160 240 320 400
1000 (2 to 3)
Flow = GPM
(2 to 3)
0 2 4 6 8 10 12 0 2 4 6 8 10 12 0 2 4 6 8 10 12 0 2 4 6 8 10 12
Flow = GPM■ Maximum operating Flowpressure
= GPM = 5000 psi Flow = GPM Flow = GPM
■
■
Will
Maximum acceptoperating
maximumpressure pressure=at5000 Portpsi**2.
■
■ Back pressure on the tank
Maximum Leakage at 150 SUS = 5 in³/min. port (port 2) is directly
at 3000 additive
psi at a 1:1 ratio to the valve setting.
■
■ Factory
Switching pressure
frequency settings
= 15000 established
cycles/hr.at 4 GPM
■
■ Proper installation
Typical response time of solenoid
10 ms. valves requires an extra deep socket to clear the solenoid tube.
■ Maximum leakage = RPCC,Snap
Sockets are available from RPEC:On 2tools (P/N SIML280)
in 3/min./1000 or Sun3Hydraulics
psi, RPGC: in3/min./1000 (P/Npsi,998-100-006).
RPIC: 4
See
www.sunhydraulics.com details. psi.
3/min./1000
** For valves produced before January 1, 2004 (date code A041), the maximum operating pressure is 5000 psi at ports 2 and 3 and 3600 psi at port 1.
■ RPCC
NOTE: Whileminimum
the valve will setting forwith
operate reliably allpressures
spring ranges
up to isPort
5000 psi at 751, psi
solenoid tube fatigue life is reduced.
D MRP
D A✱ –C ✱– ✱✱✱✱ –✱ ✱ ✱ ✱
Nominal
Nominal Price
Capacity Control Spool Configuration Coil
Capacity Control** Adjustment Range SealConfiguration*
D 10 GPM $ 52.70 M Manual +$5.00 A Normally Open +$ 0.00 ISO/DIN
C 12 GPM* $ 31.90 L Override
Standard Screw +$ 0.00 A 100
Ports 1 psi +$ 0.00
- 3000
2 to N Buna-N
212 12 VDC+$ 0.00
E 25 GPM $ 36.20 C Tamper Resistant +$ 4.10 B 50 - 1500 psi +$ 0.00 224 24 VDC
V Viton +$ 2.00
X No manual +$0.00 N Normally Open +$ 0.00 211 115 VAC
G 50 GPM $ 51.80 K Override
Handknob +$ 5.00 C 150 - 6000 psi +$ 2.00
Ports 2 to 3 223 230 VAC
I 100 GPM $ 97.30 N 60 - 800
Sealpsi +$ 1.00 AMP® Junior Timer
612 12 VDC
K 200 GPM $187.00 Q 60 - 400 psi +$ 1.00 624 24 VDC
N Buna-N
W 150 - 4500 psi +$ 0.00 Twin Lead
V Viton +$ 3.00 712 12 VDC
724 24 VDC
A, B, C, and W are standard set at 1000 psi. Deutsch
Metri-Pack
Maximum Leakage (in.3/min. at 3000 psi 812 12 VDC
with 150 SUS oil) = 5 824 24 VDC
Power (Watts) = 22
Operating Voltage Tolerance = ± 10% * See page 167 for Solenoid Twin Spade
Typical response Time (ms) = 30-50 for detailed and complete Connector
Options on our full line524
of products.
24 VDC
Relief Valves
+ -
Solenoid Operated Cartridge Valves
2-POSITION, 4-WAY 2 SPOOL DIRECTIONAL
1 VALVE
c
b
d 2 4
Locating Normally
Shoulder
Closed Cartridge Dimensions
c
3 1
b a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
Locating
25 GPM RPEC – LANTypical
T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Installation
Outlet 4 Nominal
Port Capacity RPGC – LAN
50 GPM Cartridge
Model Code
T - 3A Cavity
1.88 1a 1/8” b 2.12 c 2.18 d 2.38 Torque
45/50
(lb. ft.)
7-12 GPMRPIC –DNDA
LAN
3 a 100 GPM T - 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet
Port 1 – MCN T - 31A 3.34 7/8” 3.52 1.47 30/35
200 GPM RPKC – LAN T - 18A 3.13 1 5/8” 2.81 2.94 3.06 350/375
2
Port
Performance Curves
RPCC 1 Port RPEC RPGC RPIC RPKC
5000 5000 5000 DNDA-MCN 5000 5000
4000 4000 4000 4000
Valve Performance Limits at 10% Undervoltage Typical Performance Pressure
P = psi
4000
P = psi
P = psi
P = psi
P = psi
3000
3000 3000
and Stabilized Coil Temperature
3000
Differential vs. Flow 3000
2000 2000 5000 2000Performance limits
Note: 250
2000 P-A & P-B 2000
C Shifted
4000 are derived with 4-way A-T Shifted,
1000 P-B
1000 1000 1000 200 1000
P = psi
operation and symmetrical Not Shifted

P = psi
3000 T N flow. For valve applications 150

0 5 10 15 20 25 0 10 20E, U, 30
R, L 40 50 0
where either 20 40
asymmetrical 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
2000 100
Flow = GPM 1000 Flow = GPM
(Spool Options)
D, H, Y
Flow
flow or 3-way operation are = GPM Flow = GPM
A-T Not
Shifted Flow = GPM
present, these performance 50
limits may be reduced. B-T Shifted
■ Maximum0 operating 2 4 6
Flow = GPM
8pressure
10 12 = 5000 psi 0 2 4 6 8 10
Flow = GPM
■
■ Maximum
Back pressure operating
on thepressure
tank port= (port 5000 2) psi** is directly additive at a 1:1 ratio to the valve setting.
■ Maximum Leakage at 150 SUS = 10 in³/min. at 3000 psi
■
■ Factory
Switching frequency = 15000 cycles/hr 4 GPM
pressure settings established at
■■ Typical response time
Proper installation 10 ms. valves requires an extra deep socket to clear the solenoid tube.
of solenoid
■ Sockets are available
Maximum leakage = RPCC, from SnapRPEC: On tools2 in 3(P/N SIML280)
/min./1000 psi,or Sun Hydraulics
RPGC: (P/N 998-100-006).
3 in3/min./1000 psi, RPIC: 4
See
in www.sunhydraulics.com
3/min./1000 psi, RPKC: 5 in for details. psi.
3/min./1000
** For valves produced before January 1, 2004 (date code A041), the maximum operating pressure is
■ 5000 psi atminimum
RPCC ports 2, 3 and 4 setting
and 3600 psifor
at port
all1. NOTE:
spring While the valveis
ranges will75
operate
psireliably with
pressures up to 5000 psi at Port 1, solenoid tube fatigue life is reduced.
D NRP
DA✱C
– ✱– ✱✱ ✱✱ ✱
– ✱✱✱
Nominal
Nominal Price
Capacity Control SpoolAdjustment
Configuration Coil
Capacity Control** Range SealConfiguration*
D 7-12 GPM $ 61.20 M Manual +$5.00 C +$ 0.00 ISO/DIN
C 12 GPM* $ 31.90 L Standard
Override Screw +$ 0.00 A 100 - 3000 psi +$ 0.00 N Buna-N
212 12 +$VDC0.00
D 224 24 VDC
E 25 GPM $ 36.20 C Tamper +$ 4.10 B 50 - 1500 psi
+$0.00
Resistant
X No manual +$ 0.00 V Viton
211 115+$VAC 2.00
G 50 GPM $ 51.80 Override
K Handknob E
+$ 5.00 C 150 - 6000 psi +$ 2.00 223 230 VAC
I 100 GPM $ 97.30 H N 60 - 800 psi +$ 01.00 AMP® Junior Timer

612 12 VDC
K 200 GPM $187.00 L Q 60 - 400 psi +$ 1.00 624 24 VDC
N W 150 - 4500 psi +$ 00.00 Twin Lead

712 12 VDC
R 724 24 VDC
T A, B, C, and W are standard0 set at 1000 psi. Deutsch
U Q Option is standard set at 200 psi. 924 24 VDC
948 48 VDC
** See page 162 for information Y * Minimum setting 75 psi on all ranges.
Metri-Pack
812 12 VDC
824 24 VDC
Seal
Twin Spade
N technical
Visit www.sunhydraulics.com for detailed and complete +$ 0.00
Buna-N information on our full line524
of products.
24 VDC
Maximum Leakage (in.3/min. at 3000 psi 6 US Shortcut Catalogue #999-901-243
with 150 SUS oil) = 10 V Viton
Power (Watts) = 22 * See page 167 for Solenoid
Operating Voltage Tolerance = ± 10% Connector Options
Typical response Time (ms) = 30-50
2-POSITION, 2-WAY SPOOL DIRECTIONAL VALVE – PILOT CAPACITY
2 Normally
Closed
DAAA-MCN
2
1
Normally
c Open
DAAA-MHN 1
Cartridge Cavity a b d Torque
Capacity Model Code M C (lb. ft.)
b Locating .25 GPM DAAA – MCN T - 8A .75 7/8” 2.94 3.13 1.22 25/30
Shoulder
.25 GPM DAAA – MHN T - 8A .75 7/8” 2.94 3.13 1.22 25/30
a
2 .25 GPM DAAC – MCN T - 8A .75 7/8” 2.94 3.13 1.22 25/30
Port
Port 1 .25 GPM DAAC – MHN T - 8A .75 7/8” 2.94 3.13 1.22 25/30
Performance Curves
DAA*-M*N
Pressure vs. Flow
500
400
P = psi
300
200
100
0 0.2 0.4 0.6 0.8 1.0

Flow = GPM

■ Maximum Leakage at 150 SUS = 10 drops/min.
■ Switching frequency = 15000 cycles/hr.
■ Cartridge can be installed directly into a cavity in some Sun pilot operated and ventable cartridges
to provide electrically operated pilot control functions.
■ Proper installation of solenoid valves requires an extra deep socket to clear the solenoid tube.
Sockets are available from Snap On tools (P/N SIML280) or Sun Hydraulics (P/N 998-100-006).
See www.sunhydraulics.com for details.

D AA✱ – ✱ ✱ ✱ – ✱ ✱ ✱
Nominal
A .25 GPM $ 70.70 M Manual +$0.00 H Normally Open +$ 0.00 ISO/DIN
Override 206 6 VDC
C Concealed +$0.00 224 24 VDC
223 230 VAC
Version Seal
SAE J858
A Standard +$0.00 N Buna-N +$ 0.00 506 6 VDC
512 12 VDC
C Canadian +$16.00 V Viton +$ 2.00 524 24 VDC
Standards
Association Twin Lead
Certified 706 6 VDC
3500 psi max. 712 12 VDC
724 24 VDC
Diameter Effective Orifice (inches) = .045 * See page 167 for

Operating Voltage Tolerance = ± 10% Solenoid Connector
Power (Watts) = 12 Options
Typical response Time (ms) = 30
1 Normally
Open 1-2
d
DBAA-MHN
1
2 3
Normally
c Open 1-3
DBAA-MCN 2 3
Cartridge Cavity a b d Torque
Capacity Model Code M C (lb. ft.)
b Locating
Shoulder .25 GPM DBAA – MCN T - 9A 1.09 7/8” 2.94 3.13 1.22 25/30
3
Port a .25 GPM DBAA – MHN T - 9A 1.09 7/8” 2.94 3.13 1.22 25/30
2 .25 GPM DBAC – MCN T - 9A 1.09 7/8” 2.94 3.13 1.22 25/30
Port
Port 1 .25 GPM DBAC – MHN T - 9A 1.09 7/8” 2.94 3.13 1.22 25/30
Performance Curves
DBA*-M*N
Pressure vs. Flow
500
400
P = psi
300
200
100
0 0.2 0.4 0.6 0.8 1.0

Flow = GPM

■ Maximum Leakage at 150 SUS = 10 drops/min.
■ Switching frequency = 15000 cycles/hr.

D BA✱ – ✱ ✱ ✱ – ✱ ✱ ✱
Nominal
Override Ports 1 to 2 206 6 VDC
212 12 VDC
C Concealed +$0.00 C Normally Open +$ 0.00 224 24 VDC
Override Ports 1 to 3 211 115 VAC
223 230 VAC
Version Seal
SAE J858
512 12 VDC
Standards
Certified 706 6 VDC
3500 psi max. 712 12 VDC
724 24 VDC
* See page 167 for

Solenoid Connector
Diameter Effective Orifice (inches) = .045 Options
Operating Voltage Tolerance = ± 10%
Power (Watts) = 12
Typical response Time (ms) = 30
NOTES

Pilot Control Valves
Cartridge Type Page

2 2
2-position 2-way, Spool Directional
Valve - Pilot Capacity 122
1 1
Normally Closed Normally Open

2 2 Hydraulically Operated, 2-position
Ext. Ext.
2-way, Spool Directional Valve - Pilot 123
Capacity
1 1

2 2
Air-operated, 2-position 2-way, Spool
124
Ext. Ext. Directional Valve - Pilot Capacity
1 1

1 1
Manually Operated, 2-position 2-way,
Spool Directional Valve - Pilot 125
Capacity
2 2
Normally Open 1-3 Normally Open 1-2

1 1
2-position 3-way, Spool Directional
126
Valve – Pilot Capacity
2 3 2 3
Normally Open 1-2 Normally Closed 1-3

1 1 Hydraulically Operated, 2-position
Ext. Ext.
3-way, Spool Directional Valve - Pilot 127
Capacity
2 3 2 3
Normally Closed 1-3 Normally Open 1-2

2 3 2 3
Air-operated, 2-position 3-way, Spool
128
Ext. Ext. Directional Valve - Pilot Capacity
1 1

1 1 Manually Operated, 2-position 3-way,
Spool Directional Valve - Pilot 129
Capacity
2 3 2 3
2 1 Direct Acting, Adjustable Pilot Relief 130
Air Pilot
Air-controlled, Directing Acting Pilot 131

2 1 Relief
Fully Adjustable Needle Valve - Pilot 132

Capacity
1
2 1 Electro-proportional Pilot Relief 133

2 Normally
Closed
DAAA-MCN
2
1
Normally
c Open
DAAA-MHN 1
Capacity Cartridge Cavity a b d Torque
Model Code M C (lb. ft.)
b Locating .25 GPM DAAA – MCN T - 8A .75 7/8” 2.94 3.13 1.22 25/30
Shoulder
.25 GPM DAAA – MHN T - 8A .75 7/8” 2.94 3.13 1.22 25/30
a
2 .25 GPM DAAC – MCN T - 8A .75 7/8” 2.94 3.13 1.22 25/30
Port
Port 1 .25 GPM DAAC – MHN T - 8A .75 7/8” 2.94 3.13 1.22 25/30
Performance Curves
DAA*-M*N
Pressure vs. Flow
500
400
P = psi
300
200
100
0 0.2 0.4 0.6 0.8 1.0

Flow = GPM

■ Maximum leakage at 150 SUS = 10 drops/min. at 5000 psi
■ Switching frequency = 15000 cycles/hour
■ Cartridge can be installed directly into a cavity in some Sun pilot operated and ventable cartridges
to provide electrically operated pilot control functions.

D AAA – M ✱ ✱ – ✱ ✱ ✱
Nominal
Override 206 6 VDC
C Concealed +$0.00 224 24 VDC
223 230 VAC
Version Seal
SAE J858
512 12 VDC
Standards
Certified 706 6 VDC
3500 psi max. 712 12 VDC
724 24 VDC
Maximum Leakage (drops/min. at 5000 psi

* See page 167 for with 150 SUS oil) = 10
Solenoid Connector Diameter Effective Orifice (inches) = .045 Power (Watts) = 12
Options Operating Voltage Tolerance = ± 20% Typical response Time (ms) = 30
HYDRAULICALLY OPERATED, 2-POSITION 2-WAY, SPOOL DIRECTIONAL
VALVE - PILOT CAPACITY
2
Normally
Open
Ext. DAAH-*CN
2
1
Normally Ext.
c Closed
b DAAH-*HN
1
Locating
Model Code lb. ft.
a .25 GPM DAAH – BCN T - 8A .75 7/8” 1.66 25/30
2
Port
Port 1
Performance Curves
DAAH
Pressure vs. Flow
500
400
P = psi
300
200
100
0 0.2 0.4 0.6 0.8 1.0

Flow = GPM

■ Minimum pilot pressure to operate = 200 psi
■ All ports will accept 5000 psi including the pilot control port.
■ The preferred flow path through the valve is port 2 to port 1.

DA A H – ✱ ✱ ✱
Nominal Pilot Port Spool Configuration Seal
Capacity
A .25 GPM $ 72.10 A 1/8-27 NPTF +$ 0.00 H Normally Open +$0.00 N Buna-N
B SAE-4 +$ 0.00 C Normally Closed +$0.00 V Viton
D 1/8-28 BSPP
AIR-OPERATED, 2-POSITION 2-WAY, SPOOL DIRECTIONAL
2 Normally
Closed
DAAP-*CN
Ext.
2
1
Ext.
c Normally
b Open
DAAP-*HN 1
Locating
2 .25 GPM DAAP – FCN T - 8A .75 7/8” 1.66 25/30
Port
1 Port
Performance Curves
DAAP
Pressure vs. Flow
500
400
P = psi
300
200
100
0 0.2 0.4 0.6 0.8 1.0

Flow = GPM

■ Maximum pilot pressure = 70 psi
■ Minimum pilot pressure to operate = 20 psi + port 1 pressure/100 psi
■ All ports will accept 5000 psi with the exception of the pilot port which accepts 500 psi maximum.

DA A P – ✱ ✱ ✱
Capacity
A .25 GPM $ 83.70 E SAE-4 +$ 0.00 H Normally Open +$0.00 N Buna-N
F 1/8-27 NPTF +$ 0.00 C Normally Closed +$0.00 V Viton
P 1/8-28 BSPP
MANUALLY OPERATED, 2-POSITION 2-WAY, SPOOL DIRECTIONAL
d D Control L Control T Control

1 1 1
H Spool:
Normally
Open
2 2 2 = Twist (Momentary)
1 1 1 = Lock (Detent)
C Spool:
Normally
c Closed
2 2 2
b
2 a Capacity Cartridge Cavity a b c d Torque
Port Model Code lb. ft.
1 Port Locating .25 GPM DAAM - TCN T-8A .75 1 1/8” 2.90 1.90 25/30
Shoulder
Performance Curves
DAAM
Pressure vs. Flow
500
400
P = psi
300
200
100
0 0.2 0.4 0.6 0.8 1.0

Flow = GPM


DA A M – ✱ ✱ ✱
Capacity
A .25 GPM $ 80.00 D Dual +$ 0.00 C Normally Closed +$0.00 N Buna-N
(Twist/Lock)
H Normally Open +$0.00 V Viton
L Lock (Detent)
T Twist
(Momentary)
NOTE: Designed for 10,000

cycles of operation maximum
under normal conditions.
1 Normally
Open 1-2
d
DBAA-MHN
1
2 3
Normally
c Open 1-3
DBAA-MCN 2 3
Capacity Cartridge Cavity a b d Torque
Model Code M C (lb. ft.)
b Locating
Shoulder .25 GPM DBAA – MCN T - 9A 1.09 7/8” 2.94 3.13 1.19 25/30
3
Port a .25 GPM DBAA – MHN T - 9A 1.09 7/8” 2.94 3.13 1.19 25/30
2 .25 GPM DBAC – MCN T - 9A 1.09 7/8” 2.94 3.13 1.19 25/30
Port
Port 1 .25 GPM DBAC – MHN T - 9A 1.09 7/8” 2.94 3.13 1.19 25/30
Performance Curves
DBA*-M*N
Pressure vs. Flow
500
400
P = psi
300
200
100
0 0.2 0.4 0.6 0.8 1.0

Flow = GPM

■ Switching frequency = 15000 cycles/hour

D BAA – M ✱ ✱ – ✱ ✱ ✱
Nominal
Override Ports 1 to 2 206 6 VDC
212 12 VDC
C Concealed +$0.00 C Normally Open +$ 0.00 224 24 VDC
Override Ports 1 to 3 211 115 VAC
223 230 VAC
Version Seal
SAE J858
512 12 VDC
Standards
Certified 706 6 VDC
3500 psi max. 712 12 VDC
724 24 VDC
Maximum Leakage (drops/min. at 5000 psi

* See page 167 for with 150 SUS oil) = 10
Solenoid Connector Diameter Effective Orifice (inches) = .045 Power (Watts) = 12
Options Operating Voltage Tolerance = ± 10% Typical response Time (ms) = 30
HYDRAULICALLY OPERATED, 2-POSITION 3-WAY, SPOOL DIRECTIONAL
1 Normally
Open 1-3
DBAH-*CN
Ext.
1
2 3
c Ext.
Normally
b Open 1-2
DBAH-*HN
2 3
Locating
3 Capacity Cartridge Cavity a b c Torque
a .25 GPM DBAH – BCN T - 9A 1.09 7/8” 1.66 25/30
2
Port
Port 1
Performance Curves
DBAH
Pressure vs. Flow
500
400
P = psi
300
200
100
0 0.2 0.4 0.6 0.8 1.0

Flow = GPM

■ Minimum pilot pressure to operate = 200 psi
■ All ports will accept 5000 psi including the pilot control port.

DB A H – ✱ ✱ ✱
Nominal
Capacity Pilot Port Spool Configuration Seal
A .25 GPM $ 84.70 A 1/8-27 NPTF +$ 0.00 H Normally Open +$0.00 N Buna-N
Ports 1 to 2
B SAE-4 +$ 0.00 V Viton
C Normally Open
D 1/8-28 BSPP +$ 0.00 Ports 1 to 3
AIR-OPERATED, 2-POSITION 3-WAY, SPOOL DIRECTIONAL
2 3 Normally
Open 1-2
DBAP-*HN
Ext.
2 3
1
c
b Normally Ext.
Open 1-3
DBAP-*CN
1
Shoulder
Port a
.25 GPM DBAP – FCN T - 9A 1.09 7/8” 1.66 25/30
2
Port
1 Port
Performance Curves
DBAP
Pressure vs. Flow
500
400
P = psi
300
200
100
0 0.2 0.4 0.6 0.8 1.0

Flow = GPM

■ Maximum leakage at 150 SUS = 10 drops/min. at 5000 psi.
■ Minimum pilot pressure to operate = 20 psi + port 1 pressure/100 psi
■ All ports will accept 5000 psi with the exception of the pilot port which accepts 500 psi maximum.

D B A P – ✱✱✱
Nominal
Capacity Pilot Port Spool Configuration Seal
A .25 GPM $ 85.90 E SAE-4 +$ 0.00 H Normally Open +$ 0.00 N Buna-N
Ports 1 to 2
F 1/8-27 NPTF +$ 0.00 V Viton
C Normally Open
P 1/8-28 BSPP +$ 0.00 Ports 1 to 3
MANUALLY OPERATED, 2-POSITION 3-WAY, SPOOL DIRECTIONAL
d D Control L Control T Control

1 1 1
H Spool:
Normally
Open
2 3 2 3 2 3 = Twist (Momentary)
1 1 1 = Lock (Detent)
C Spool:
Normally
c Closed
2 3 2 3 2 3
b
3 a Model Code (lb. ft.)
Port 2
Port .25 GPM DBAM – TCN T - 9A 1.09 1 1/8” 2.40 1.40 25/30
1 Port Locating
Shoulder
Performance Curves
DBAM
Pressure vs. Flow
500
400
P = psi
300
200
100
0 0.2 0.4 0.6 0.8 1.0

Flow = GPM

■ All ports will accept 5000 psi.

D B A M – ✱✱✱
Nominal
Pilot Port Spool Configuration Seal
Capacity
A .25 GPM $ 97.00 D Dual +$ 0.00 C Normally +$0.00 N Buna-N
(Twist/Lock) Open 1-3
V Viton
L Lock (Detent) +$ 0.00 H Normally
Open 1-2
T Twist
(Momentary)
NOTE: Designed for 10,000

cycles of operation maximum
under normal conditions.
DIRECT ACTING, ADJUSTABLE PILOT RELIEF
+ -
2 1
c
b Model Code L C K (lb. ft.)
2.5 GPM RBAE – LAN T - 8A .75 7/8” 2.38 2.47 2.66 25/30
Locating
Shoulder
a
2
Port
Port 1
Performance Curves
RBAE
Pressure vs. Flow
5000
4000
P = psi
3000
2000
1000
0 1 2 3
Flow = GPM

■ Maximum leakage = 5 drops/min. at reseat (reseat = 85% of cracking pressure).
■ Ports 1 and 2 may be pressured to 5000 psi.
■ Back pressure at port 2 (outlet) is directly additive to the pressure setting at port 1 (inlet).

R B A E – ✱✱✱
Nominal
Capacity
A 2.5 GPM $ 41.40 L Standard Screw +$ 0.00 A 25 - 3000 psi +$ 0.00 N Buna-N
C Concealed +$ 4.10 B 25 -1500 psi +$ 0.00 V Viton
K Handknob +$ 5.00 C 25 - 6000 psi
D 25 - 800 psi
E 25 - 400 psi
W 25 - 4500 psi

on Control Options E Option is standard set at 200 psi.
Customer may specify pressure setting.
AIR-CONTROLLED, DIRECTING ACTING PILOT RELIEF
Air Pilot
2 1
c
b Cartridge Dimensions
Locating Model Code (lb. ft.)
Shoulder
2.5 GPM RBAR – AWN T - 8A .75 7/8” 1.60 25/30
2.5 GPM RBAR – AYN T - 8A .75 1 1/8” 1.60 25/30
a
2
Port
Port 1
Performance Curves
RBAR
Air to Oil at 0.1 GPM Pressure vs. Flow
6000 6000 70 psi Air
5000
Hydraulic
5000
Pressure
58 psi Air
P = psi
4000 4000 42 psi Air

3000 3000
30 psi Air
2000 2000
18 psi Air
1000 1000
0 20 40 60 80 100 0 1 2
Air Pressure - psi Flow = GPM

■ Maximum leakage = 5 drops/min. at 5000 psi
■ Back pressure at port 2 has no effect on the valve setting.
■ The main stage valve should first be installed to the correct torque value followed by the T-8A
pilot control section into the main stage valve to its required torque value.

R B A R – ✱✱✱
Nominal
Capacity Port Air Pilot Ratio Seal
A 2.5 GPM $ 88.00 A 1/8-27 NPTF +$ 0.00 W 50:1 +$ 0.00 N Buna-N

Pilot Port
Y 75:1 +$10.30 V Viton
B SAE-4 Pilot Port
D 1/8-28 BSPP Port
FULLY ADJUSTABLE NEEDLE VALVE - PILOT CAPACITY
2
c
b 1

Shoulder Maximum Typical Installation
Cartridge Cavity a b c Torque
Orifice Model Code (lb. ft.)
a
2 .035 in. NFAB – KXN T - 8A .75 7/8” 1.10 25/30
Port
Port 1

■ Maximum leakage at shutoff = less than 5 drops/min. at 5000 psi
■ Effective orifice size = .035 in.
■ Number of counterclockwise turns fully closed to fully open = 3

N F A B – K X ✱
Model
Control Maximum Orifice Seal
Code
NFAB-KXN +$21.10 K Handknob +$ 0.00 X .035 in. +$ 0.00 N Buna-N
V Viton
ELECTRO-PROPORTIONAL PILOT RELIEF
Relief Valves
2 1
+ -
d
2 1
b Capacity Cartridge Cavity a b c d Torque
c Model Code (lb. ft.)
b Locating Locating
.25 GPM RBAP – MAN T - 8A .75 7/8 .59 2.76 25/30
Shoulder Shoulder Cartridge Dimensions
2 a
Outlet Typical c Installation
Inlet 1
a 12 GPM RPCC – LAN T - 162A 1.22 3/4” 2.11 2.17 2.31 25/30
2 25 GPM RPEC – LAN T - 10A 1.56 7/8” 2.00 2.06 2.25 30/35
Outlet
Performance Curves 50 GPM RPGC – LAN T - 3A 1.88 1 1/8” 2.12 2.18 2.38 45/50
100 GPM RPIC – LAN TRBAP
- 16A 2.44 1 1/4” 2.44 2.47 2.69 150/160
Inlet 1
RPKC –Command
200 GPM Constant LAN T - 18A Pressure
3.13vs. Command
1 5/8” 2.81 2.94 3.06 350/375
Varying Flow Flow 0.1 GPM
Performance Curves 4000 4000
RPCC RPEC RPGC 3000

RPIC RPKC
P = psi
3000
P = psi
2000 2000
1000
Typical Pressure
1000
Rise
5000 5000 5000 5000 5000
0 25 50 75 100 120 0 20 40 60 80 100
4000 4000 4000 4000
P = psi
4000
inch3/min. Command (%)
P = psi
P = psi
P = psi
P = psi
3000 3000 3000 3000 3000

2000 2000 2000 2000 2000
1000 ■ Maximum
1000 operating pressure 1000= 5000 psi 1000 1000
0 5 10 15 20 ■25
MaximumFlow
0 10
leakage
20 30 40 50 3
= 1.5 in /min at reseat
0 20 40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400
Flow = GPM = GPM Flow = GPM Flow = GPM Flow = GPM
■ Back pressure on the tank port (port 2) is directly additive at a 1:1 ratio to valve setting
■ Hysteresis with dither <4%
■ Hysteresis with DC input <8%
■ Linearity with dither <2%
■ For optimum performance, an amplifier 3with current sensing and adjustable 3 dither should be used.
■ Maximum
Dither leakage
should = RPCC, between
be adjustable RPEC: 2100 in /min./1000
- 250 Hz. psi, RPGC: 3 in /min./1000 psi, RPIC: 4
3 3
RP AC
RB ✱ P – ✱ ✱✱
Nominal
Nominal
Capacity Control**
Adjustment Range
Range Seal
Seal
Capacity
A .25 GPM $105.00 M Manual Override +$ 0.00 A 300 - 3000 psi +$ 0.00 N Buna-N
E 25 GPM $ 36.20 C Tamper Resistant +$
(Standard) 4.10 B 50 - 1500 psi +$ 0.00 V Viton +$ 2.00
G 50 GPM $ 51.80 K Handknob +$ 5.00 B 150
C 150--6000
1500psi
psi +$ 2.00
+$ 0.00 V Viton
NOTE: Coil must be
I 100 GPM $ 97.30 ordered separately. Use N
W 60
500- 800 psipsi
- 5000 +$ 1.00
K 200 GPM $187.00 12V DC or 24V DC Q 60 - 400 psi +$ 1.00

on Control Options and complete technical information
Customer on our full
may specify pressure line of products.
setting. +$ 1.10
NOTES

Shuttle Valves
Cartridge Type Page
1 2 1 Ext. Single Ball Shuttle 136
Ext. 2
Single Ball Shuttle Valve with Signal at

1 2 1 3 137
Port 3 or Port 2
3 2
1 2 1 Ext. Back-to-back Check/Shuttle 138
Ext. 2
1 2 1 3 Back-to-back Check/Shuttle 139
3 2
2 4
Low Side, 3-position, Hot Oil Shuttle
140
Valve
2 4
High Side, 3-position, Shuttle Valve 141
4 2
Spring Offset, 2-position, High Side
142
Shuttle

Shuttle Valves
SINGLE BALL SHUTTLE
External Port 1 2 1 Ext.
b
c Ext. 2
Locating
Shoulder CSAW/CSAA CSAY/CSAC
a Nominal Typical Installation
Cartridge Cavity a b c Torque
2 Capacity Model Code lb. ft.
Port
1.25 GPM CSAW– BXN T - 162A 1.22 3/4” .81 25/30
Port 1 1.25 GPM CSAY – BXN T - 162A 1.22 3/4” .81 25/30
2.5 GPM CSAA – BXN T - 13A 1.38 7/8” 1.19 30/35
2.5 GPM CSAC – BXN T - 13A 1.38 7/8” 1.19 30/35
Performance Curves
CSAW/CSAY CSAA/CSAC
300 300
P = psi
P = psi
200 200
100 100
0 0.5 1.0 1.5 2.0 0 1 2 3 4 5


■ Maximum valve leakage = 5 drops/min.

CS A ✱ – ✱ X ✱
Nominal Capacity
and Version Control Seal
W 1.25 GPM $ 18.90 B .25 BSPP External +$0.00 N Buna-N

Signal at External Port Port
+$0.00 V Viton
Y 1.25 GPM $ 18.90 E SAE-4 External
Signal at Port 2 Port
A 2.5 GPM
Signal at External Port
C 2.5 GPM
Signal at Port 2
Shuttle Valves
SINGLE BALL SHUTTLE VALVE WITH SIGNAL AT PORT 3 OR PORT 2
b 1 2 1 3
c
3 2
3
Locating
Port Shoulder CSAX/CSAB CSAD/CSAZ
a Nominal Cartridge Cavity a b c Torque
2 Capacity Model Code lb. ft.
Port
1.25 GPM CSAX – XXN T - 163A 1.22 3/4” 1.25 25/30
Port 1 1.25 GPM CSAZ – XXN T - 163A 1.22 3/4” 1.25 25/30
2.5 GPM CSAB – XXN T - 11A 1.38 7/8” 1.17 30/35
2.5 GPM CSAD – XXN T - 11A 1.38 7/8” 1.19 30/35
Performance Curves
CSAX/CSAZ CSAB/CSAD
300 300
P = psi
P = psi
200 200
100 100
0 0.5 1.0 1.5 2.0 0 1 2 3 4 5



CS A ✱ – X X ✱
Nominal Capacity
Control Seal
and Version
X 1.25 GPM $ 13.00 X Non-adjustable +$0.00 N Buna-N
Signal at Port 3
V Viton
Z 1.25 GPM
Signal at Port 2
B 2.5 GPM
Signal at Port 3
D 2.5 GPM
Signal at Port 2
Shuttle Valves
BACK-TO-BACK CHECK/SHUTTLE
1 2 1 Ext.
b
c
Locating Ext. 2
Shoulder
CDAA CDAC
Port Capacity Model Code lb. ft.
Port 1 2.5 GPM CDAA – BBN T - 13A 1.38 7/8” 1.19 30/35
2.5 GPM CDAC – BBN T - 13A 1.38 7/8” .75 30/35
Performance Curves
CDAA/CDAC
400
300
P = psi
200
100
0 1 2 3 4 5
Flow = GPM

■ The back-to-back checks do not provide a means of lowering a signal. They will trap a high signal if
the load pressures drop to a lower pressure. Some means of bleeding off the signal should be provided.
■ 15 psi check.

CD A ✱ – ✱ B ✱
Nominal Capacity
Control Seal
and Version
A 2.5 GPM $ 25.20 B .25 BSPP +$ 0.00 N Buna-N
Signal at External External Port
Port V Viton
C 2.5 GPM $ 25.20 E SAE-4

Signal at External Port
Port 2
Shuttle Valves
BACK-TO-BACK CHECK/SHUTTLE
1 2 1 3
b
c 3 2
3 CDAB CDAD
Port Locating
Shoulder
a Nominal Typical Installation
2.5 GPM CDAB – XBN T - 11A 1.38 7/8” 1.19 30/35
Port 1 2.5 GPM CDAD – XBN T - 11A 1.38 7/8” 1.19 30/35
Performance Curves
CDAB/CDAD
400
300
P = psi
200
100
0 1 2 3 4 5
Flow = GPM

■ The back-to-back checks do not provide a means of lowering a signal. They will trap a high signal if
the load pressures drop to a lower pressure. Some means of bleeding off the signal should be provided.
■ 15 psi check

CD A ✱ – X B ✱
Nominal Capacity
Control Seal
and Version
B 2.5 GPM $ 19.60 X Non-adjustable +$ 0.00 N Buna-N +$ 0.00
Signal at Port 3
V Viton
D 2.5 GPM
Signal at Port 2
Shuttle Valves
LOW SIDE, 3-POSITION, HOT OIL SHUTTLE VALVE
2 4
b c
Locating
Shoulder
3
4
Port
Port
Capacity Model Code lb. ft.
2 15 GPM DSCH – XHN T - 31A 3.35 7/8” 1.19 30/35
Port
30 GPM DSEH – XHN T - 32A 3.63 1 1/8” 1.31 45/50
Port 1 Not Used 60 GPM DSGH – XHN T - 33A 4.50 1 1/4” 1.63 150/160
120 GPM DSIH – XHN T - 34A 5.50 1 5/8” 2.00 350/375
Performance Curves
DSCH DSEH DSGH DSIH
400 400 400 400
300 300 300 300

P = psi
P = psi
P = psi
P = psi
200 200 200 200
100 100 100 100
0 5 10 15 20 0 10 20 30 40 0 10 20 30 40 50 60 70 0 20 40 60 80 100 120 140


■ Pilot flow = DSCH, DSEH: 23 in³/min., DSGH, DSIH: 46 in³/min. (Port 2 and 4 to Port 3).
■ Note: Low shift values can potentially result in charge pump pressure alone inadvertently shifting
the valve. Use care when selecting shift pressure.
■ Pressures on Ports 2 and 4 must equalize before reversed shift can take place.

DS ✱ H – X ✱ ✱
Nominal
Control Shifting Pressure Seal
Capacity
C 15 GPM $ 82.10 X Non-adjustable +$ 0.00 G 150 psi +$ 3.00 N Buna-N
E 30 GPM $108.30 H 200 psi +$ 0.00 V Viton
G 60 GPM
I 120 GPM
Shuttle Valves
HIGH SIDE, 3-POSITION, SHUTTLE VALVE
2 4
Locating 3
Shoulder
4
a Model Code lb. ft.
3
Port 15 GPM DSCS – XCN T - 31A 3.35 7/8” 1.44 30/35
2 30 GPM DSES – XCN T - 32A 3.63 1 1/8” 1.63 45/50

Port 60 GPM DSGS – XCN T - 33A 4.50 1 1/4” 2.83 150/160
120 GPM DSIS – XCN T - 34A 5.50 1 5/8” 4.21 350/375
Port 1 Not Used
Performance Curves
DSCS DSES DSGS DSIS
Pressure Drop, Port 2 or 4 to Port 3
200 200 200 200
150 150 150 150

P = psi
P = psi
P = psi
100 100 100 P = psi 100
50 50 50 50
0 4 8 12 16 0 10 20 30 0 20 40 60 0 40 80 120

■ Maximum valve leakage = DSCS: 2 in³/min. at 1000 psi, DSES: 3 in³/min. at 1000 psi, DSGS:
4 in³/min. at 1000 psi, DSIS: 5 in³/min. at 1000 psi

DS ✱ S – X ✱ ✱
Nominal
Control Shifting Pressure Seal
Capacity
C 15 GPM $ 71.50 X Non-adjustable +$ 0.00 C 30 psi +$ 3.00 N Buna-N
E 30 GPM $ 97.80 E 75 psi +$ 3.00 V Viton
G 60 GPM $163.60 F 100 psi
I 120 GPM $307.50 G 150 psi
Shuttle Valves
SPRING OFFSET, 2-POSITION, HIGH SIDE SHUTTLE
4 2
b
Locating 3
Shoulder
3
a Model Code lb. ft.
Port 15 GPM DSCO – XCN T - 31A 3.35 7/8” 1.44 30/35
2 30 GPM DSEO – XCN T - 32A 3.63 1 1/8” 1.63 45/50
Port 60 GPM DSGO – XCN T - 33A 4.50 1 1/4” 2.83 150/160
120 GPM DSIO – XCN T - 34A 5.50 1 5/8” 4.21 350/375
Port 1 Not Used
Performance Curves
DSCO DSEO DSGO DSIO
Pressure Drop, Port 4 or 2 to Port 3
200 200 200 200
150 150 150 150

P = psi
P = psi
P = psi
P = psi
100 100 100 100
50 50 50 50
0 4 8 12 16 0 10 20 30 0 20 40 60 0 40 80 120

■ Minimum pilot pressure required to shift valve = C Range: 30 psi, E Range: 75 psi

DS ✱ O – X ✱ ✱
Nominal Control Shifting Pressure Seal
Capacity
E 30 GPM $103.10 E 75 psi +$ 0.00 V Viton
G 60 GPM
I 120 GPM
Circuit Savers
Cartridge Type Page
Fixed Orifice, Flow Fuse Valve 144
Air Bleed and Start-up Valve 145
Check, Pilot-to-Close 146

3
3
Check, Pilot-to-Close 147
Accumulator Sense, Pump Unload Valve - Pilot Capacity 148

1
3
Accumulator Sense, Pump Unload Valve
149
1 with Check - Pilot Capacity
4 2
2
Direct Acting, 2-way Directional Valve with Drain to
150
4 1 Port 4 - Normally Closed
3
2
Direct Acting, 2-way Directional Valve with Drain to
151
4 1 Port 4 - Normally Open
3
4 2
1
Vent-to-shift 2-position Diverter Valve - Normally Closed 152
4 2
1
Vent-to-shift, 2-position, 3-way Diverter Valve 153
Normally Open, Bi-directional, Modulating Logic Element 154

1
4
2

Circuit Savers
FIXED ORIFICE, FLOW FUSE VALVE
2
b
c
Locating
Shoulder
1
Model Code lb. ft.
Port
.5-6 GPM FQCA – XAN T - 13A 1.38 7/8” .75 30/35
1-15 GPM FQEA – XAN T - 5A 1.62 1 1/8” .69 45/50
Port 1
1-25 GPM FQGA – XAN T - 16A 2.44 1 1/4” .97 150/160
1-50 GPM FQIA – XAN T - 18A 3.13 1 5/8” 1.19 350/375
Performance Curves
FQCA FQEA FQGA FQIA
150 150 150 150
P = psi
P = psi
P = psi
P = psi
100 100
100 100
50 50
0 25 50 75 100 0 25 50 75 100 0 25 50 75 100 0 25 50 75 100

Percentage of Setting Percentage of Setting Percentage of Setting Percentage of Setting

■ Maximum valve leakage = FQCA: 2 in³/min. at 1000 psi, FQEA: 3 in³/min. at 1000 psi, FQGA:
4 in³/min. at 1000 psi, FQIA: 5 in³/min. at 1000 psi.
■ Valve closes when flow from port 1 to port 2 exceeds the setting of the valve. Valve resets when
pressures at port 1 and port 2 are equal.
■ Flow setting should be at least 25% above maximum normal system flow.

FQ ✱ A – X A ✱
Nominal
Capacity Control** Flow Rate Seal
C .5-6 GPM $ 30.60 X Non-adjustable +$ 0.00 A +$ 0.00 N Buna-N
E 1-15 GPM $ 43.90 V Viton
G 1-25 GPM
I 1-50 GPM $165.00 Customer must specify flow.
Circuit Savers
AIR BLEED AND START-UP VALVE
b
c
Locating
Shoulder 1
Tank Capacity Cartridge Cavity a b c Torque
Model Code lb. ft.
Pump 1 4-50 GPM NQEB – XAN T - 3A 1.88 1 1/8” .69 45/50
Performance Curves
NQEB
Approximate Closing Time
Typical Pressure Drop after Air has been Purged
200 200
150 150
P = psi
P = psi
100 100
50 50
0 10 20 30 40 50 0 10 20 30 40 50

■ Air-bleed and start-up valves require a minimum of 4 GPM flow rate and 80 psi system pressure.
■ The valve will re-open when system pressure falls below 25 psi.
■ After air has been purged, closing times vary from approximately 12 seconds at 4 GPM to 0.5
seconds at 50 GPM.

NQ E B – X A ✱
Nominal
Control** Flow Rate Seal
Capacity
E 4-50 GPM $ 49.90 X Non-adjustable +$ 0.00 A +$ 0.00 N Buna-N
V Viton
Circuit Savers
CHECK, PILOT-TO-CLOSE
2
b
3
c
3 1
Pilot Locating
Shoulder
a Orifice Typical Installation
2 Cartridge Cavity a b c Torque
Diameter
Outlet Model Code lb. ft.
.05 in. COFO – XDN T - 2A 1.38 1 1/8 1.38 45/50
1 Inlet
Performance Curves
COFO
Pressure vs. Flow
1000
800
P = psi
600
400
200
0 1 2 3
Flow = GPM

■ Pilot ratio = 120:1
■ Leakage rate when closed = 5 drops/min.

CO F O – X D N
Orifice Control** Minimum Pressure Seal
Diameter
F .05 in. $ 76.90 X Standard Pilot +$ 0.00 D 50 psi +$ 0.00 N Buna-N
V Viton

on Control Options.
Circuit Savers
CHECK, PILOT-TO-CLOSE
3
b
3 1
Port Locating
Shoulder
2 Model Code lb. ft.
Port 10 GPM COBA – XCN T - 163A 1.22 3/4” 1.22 25/30
20 GPM CODA – XCN T - 11A 1.38 7/8” 1.19 30/35
Port 1
40 GPM COFA – XCN T - 2A 1.38 1 1/8” 1.38 45/50
80 GPM COHA – XCN T - 17A 1.81 1 1/4” 1.81 150/160
160 GPM COJA – XCN T - 19A 2.50 1 5/8” 2.31 350/375
Performance Curves
COBA CODA COFA COHA COJA
200 200 200 200 200
150 150 150 150 150

P = psi
P = psi
P = psi
P = psi
P = psi

XAN XAN XAN XAN
XAN
0 2.5 5 7.5 10 0 10 15 20 0 10 20 30 40 0 25 50 75 100 0 100 150 200


■ Pilot ratio = 1.8:1
■ Leakage rate when closed = 1 drop/min.

CO ✱ A – ✱ ✱ ✱
Nominal
Control** Cracking Pressure Seal
Capacity
B 10 GPM $ 29.40 X Standard Pilot +$ 0.00 A* 4 psi +$ 1.00 N Buna-N
D 20 GPM $ 29.40 B* 15 psi +$ 1.00 V Viton
F 40 GPM $ 41.40 C 30 psi
H 80 GPM $ 71.80 D 50 psi
J 160 GPM $138.30 E 75 psi
F 100 psi
* COBA and COFA are not

** See page 162 for information available in A and B
on Control Options Cracking Pressures.
Circuit Savers
ACCUMULATOR SENSE, PUMP UNLOAD VALVE - PILOT CAPACITY

+ -
c 3
b
Port Shoulder Model Code L C lb. ft.
.2 GPM QPAA – LAN T - 11A 1.38 7/8” 2.50 2.56 30/35
a
2
Port
Port 1

■ When applying this cartridge, a separate drain line is required to prevent erratic operation caused by
tank line pressure fluctuations.
■ Note: Careful consideration should be given when selecting an adjustment range. System pressure
drops and flows tend to affect the operation of unloading valves.
QP A ✱ – ✱✱✱
Nominal
Capacity Version Control** Adjustment Range Seal
A .2 GPM $ 104.30 A 15% Nominal +$ 0.00 L Standard Screw +$ 0.00 A 1000 - 3000 psi +$ 0.00 N Buna-N
Differential
B 20% Nominal
Differential C 2000 - 5000 psi
C 30% Nominal +$ 0.00 D 200 - 800 psi

Differential
D 50% Nominal
Differential

A and B Options are standard set at 1000 psi.
** See page 162 for information C Option is standard set at 2000 psi.
Circuit Savers
ACCUMULATOR SENSE, PUMP UNLOAD VALVE WITH
CHECK - PILOT CAPACITY
+ -
b 4 2
c
Port
Model Code L C lb. ft.
3
Port
Locating .2 GPM QCDA – LAN T - 21A 1.38 7/8” 3.09 3.15 30/35
Shoulder
a
2
Port
Port 1

■ Check valve capacity = 12 GPM
■ Pressure drop, port 1 to port 2 = 70 psi at 12 GPM
■ When applying this cartridge, a separate drain line is required to prevent erratic operation caused
by tank line pressure fluctuations.
■ Note: Careful consideration should be given when selecting an adjustment range. System pressure
drops and flows tend to affect the operation of unloading valves.
QC D ✱ – ✱✱✱
Nominal
Capacity Version Control** Adjustment Range Seal
D .2 GPM $ 115.10 A 15% Nominal +$ 0.00 L Standard Screw +$ 0.00 A 1000 - 3000 psi +$ 0.00 N Buna-N +$ 0.00
Differential
B 20% Nominal
Differential C 2000 - 5000 psi
C 30% Nominal +$ 0.00 D 200 - 800 psi
Differential
D 50% Nominal
Differential

A and B Options are standard set at 1000 psi.
Circuit Savers
DIRECT ACTING, 2-WAY DIRECTIONAL VALVE WITH DRAIN TO
PORT 4 - NORMALLY CLOSED
+ -
4 1
b 3
c
Port
Locating Model Code lb. ft.
Port Shoulder
.5 GPM DRAX – LAN T - 21A 1.38 7/8” 3.09 30/35
a
2
Port
Port 1
Performance Curves
DRAX
Pressure Drop vs. Flow
Port 2 to Port 3
200
150
P = psi
100
50
0 .1 .2 .3 .4 .5 .6 .7 .8 .9 1.0
Flow = GPM

■ The pilot area (port 1) and the spring chamber drain (port 4) are positively sealed.
■ There is spool leakage between the work ports (ports 2 and 3), .03 in³/min. at 1000 psi.

DR A X – L ✱ N
Nominal
Capacity
A .5 GPM $106.90 L Standard Screw +$ 0.00 A 1000 - 3000 psi +$ 0.00 N Buna-N
C 2000 - 6000 psi +$ 2.00 V Viton

A Option is standard set at 1000 psi.
Circuit Savers
DIRECT ACTING, 2-WAY DIRECTIONAL VALVE WITH DRAIN TO PORT
4 - NORMALLY OPEN
2
+ -
4 1
b
3
c
4
Port
Locating
Port Shoulder Model Code lb. ft.
.5 GPM DRAY – LAN T - 21A 1.38 7/8” 3.09 30/35
a
2
Port
Port 1
Performance Curves
DRAY
Pressure Drop vs. Flow
Port 2 to Port 3
200
150
P = psi
100
50
0 .1 .2 .3 .4 .5 .6 .7 .8 .9 1.0
Flow = GPM

■ The pilot area (port 1) and the spring chamber drain (port 4) are positively sealed.
■ There is spool leakage between the work ports (ports 2 and 3), .03 in³/min. at 1000 psi.

DR A Y – L ✱ N
Nominal Base Control** Adjustment Range Seal
Capacity
A .5 GPM $106.90 L Standard Screw +$ 0.00 A 1000 - 3000 psi +$ 0.00 N Buna-N
C 2000 - 6000 psi +$ 0.00 V Viton

A Option is standard set at 1000 psi.
Circuit Savers
VENT-TO-SHIFT 2-POSITION DIVERTER VALVE - NORMALLY CLOSED
b 4 2
c
1
Locating
Shoulder
3
4
Port
a
Model Code lb. ft.
15 GPM DSCX – XEN T - 31A 3.34 7/8 1.19 30/35
2
Port
30 GPM DSEX – XEN T - 32A 3.63 1 1/8 1.31 45/50
60 GPM DSGX – XEN T - 33A 4.51 1 1/4 1.63 150/160
120 GPM DSIX – XEN T - 34A 5.50 1 5/8 2.12 350/375
1 Port
Performance Curves
DSCX DSEX DSGX DSIX
300 400 250 250
250 200 200 Fl
Flow
300 Fl
Flow
P = psi
3 to 2
P = psi
P = psi
3 to 2 3 to 4
200 Flow
Fl
150 150
3 to 2
Flow
Fl
3 to 4 3 to 2
Fl
Flow 100 XEN
P
3 to 4 XEN Fl
Flow
XEN 3 to 4
100 XEN XDN
XCN XCN XCN
0 5 15 20 0 10 15 20 25 30 0 20 30 40 50 60 0 20 40 60 80 100
Flow = GPM Flo M Flow = GPM Flow = GPM

■ Nominal vent flow = DSCX. DSEX: 23 in³/min., DSGX, DSIX: 35 in³/min.

DS ✱ X – X E ✱
Nominal Control Minimum Control Pressure Seal
Capacity
E 30 GPM $ 89.80 D 50 psi +$ 1.00 V Viton
G 60 GPM $146.80 E 75 psi
I 120 GPM
Circuit Savers
VENT-TO-SHIFT, 2-POSITION, 3-WAY DIVERTER VALVE
b 4 2
c
1
Locating
Shoulder
3
4
Port
Model Code lb. ft.
15 GPM DSCY – XEN T - 31A 3.34 7/8 1.19 30/35
2
Port
30 GPM DSEY – XEN T - 32A 3.63 1 1/8 1.31 45/50
60 GPM DSGY – XEN T - 33A 4.51 1 1/4 1.63 150/160
120 GPM DSIY – XEN T - 34A 5.50 1 5/8 2.12 350/375
1 Port
Performance Curves
DSCY DSEY DSGY DSIY
250 400 250 250
P3 to 1 > 100 psi
200 300 200 200 Fl
Flow
Fl
Flow
P = psi
P = psi
3 to 2
150
3 to 2 Flow
Fl
3 to 2 150 P = psi 150
Fl
Flow Self-Piloted (1 Vented)
3 to 4
200 3 to 2 3 to 4
100 XEN Fl
Flow 100 XEN XEN Fl
Flow
3 to 4
XDN 100 XDN 3 to 4
XEN
XCN XCN
0 5 10 15 20 0 5 10 15 25 30 0 20 30 40 50 60 0 20 40 60 80 100
Flow = GPM Flo M Flow = GPM Flow = GPM

■ Nominal vent flow = DSCY. DSEY: 23 in³/min., DSGY, DSIY: 35 in³/min.

DS ✱ Y – X E ✱
Nominal Control Minimum Control Pressure Seal
Capacity
E 30 GPM $ 89.80 D 50 psi +$ 1.00 V Viton
G 60 GPM $146.80 E 75 psi
I 120 GPM
Circuit Savers
NORMALLY OPEN, BI-DIRECTIONAL, MODULATING LOGIC ELEMENT
b 3
c
1
Locating
Shoulder
4
2
4
Port
a
Port
Model Code lb. ft.
15 GPM LHDT – XFN T - 31A 3.34 7/8 1.19 30/35
2 30 GPM LHFT – XFN T - 32A 3.63 1 1/8 1.31 45/50
Port
60 GPM LHHT – XFN T - 33A 4.50 1 1/4 1.63 150/160
1 Port
Performance Curves
LHDT LHFT LHHT
Typical Performance Pressure Differential vs. Flow
20 28 60
Flow = GPM
Flow = GPM
Flow = GPM
24 50
16
20 40
12 16
30
8 12
8 20
4 10
4
0 1000 2000 3000 4000 0 1000 2000 3000 4000 0 1000 2000 3000 4000
P = psi P = psi P = psi

LH ✱ T – X F ✱
Nominal
Capacity Control Nominal Control Pressure Seal
D 15 GPM $ 73.30 X Non-adjustable +$ 0.00 D 50 psi +$ 0.00 N Buna-N
F 30 GPM $ 95.00 E 75 psi +$ 0.00 V Viton
H 60 GPM $154.50 F 100 psi
Hybrid Relief Valves
Cartridge Type Page
3 Direct Acting Relief Valve - Before Check 156

2
3 Direct Acting Relief Valve - After Check 157

2
3 Ventable, Pilot Operated, Balanced Piston, Relief

158
Valve - Before Check
2 4
3 Ventable, Pilot Operated, Balanced Piston,

Relief Valve - Before Check with Integral 159
T-8A Pilot Control Cavity
2 4

Hybrid Valves
DIRECT ACTING RELIEF VALVE - BEFORE CHECK
b c 2
3
Port Typical c Installation
10 GPM HRDA – LAN T - 11A 1.38 7/8 3.09 3.15 3.34 30/35
a
2
Port
1 Port
Performance Curves
HRDA
Flow from Port 2 to Port 3 Flow from
with Port 1 Blocked Port 2 to Port 1
4000 300
3000
P = psi
P = psi
200
2000
100
1000
Mimimum
Setting
0 5 10 15 0 5 10 15

■ Reseat exceeds 85% of crack pressure
■ Typical response = 2 ms
■ The check portion of the valve has a maximum leakage rate of less than 1 drop/minute.
■ Note: This valve deviates from Sun's normal flow path for three port relief valves; port 2 is the inlet,
port 1 is the system and port 3 is tank. Therefore, it is probably not useable in existing standard
Sun relief manifolds.

HR D A – L A N
Nominal
Capacity
Adjustment
C Tamper Resistant +$ 4.10 W 800 - 4500 psi +$ 0.00 V Viton
Factory Set
K Handknob

Hybrid Valves
DIRECT ACTING RELIEF VALVE - AFTER CHECK
b c
2
3
Port Typical c Installation
Shoulder
10 GPM HRDB – LAN T - 11A 1.38 7/8 3.09 3.15 3.34 30/35
a
2
Port
1 Port
Performance Curves
HRDB
4000 300
3000
P = psi
P = psi
200
2000
100
1000
Mimimum
Setting
0 5 10 15 0 5 10 15

■ Reseat exceeds 85% of crack pressure
■ Note: This valve deviates from Sun's normal flow path for three port relief valves; port 2 is the inlet,
port 1 is the system and port 3 is tank. Therefore, it is probably not useable in existing standard
Sun relief manifolds.

HR D B – L A N
Nominal
Adjustment
C Tamper Resistant +$ 4.10 W 800 - 4500 psi +$ 0.00 V Viton
Factory Set
K Handknob

Hybrid Valves
VENTABLE, PILOT OPERATED, BALANCED PISTON,
RELIEF VALVE - BEFORE CHECK
b
c
2 4
4
Port
Port Locating Capacity Cartridge Cavity a b Torque
a
10 GPM HVCA – LAN T - 21A 1.38 7/8 3.09 3.15 3.34 30/35
2
Port
1 Port
Performance Curves
HVCA
4000 300
3000
P = psi
P = psi
200
2000
100
1000 Mimimum
Setting
0 5 10 15 0 5 10 15

■ Maximum valve leakage (port 2 to port 3) = 2 in³/min. at 1000 psi
■ Minimum setting is 75 psi for all spring ranges.
■ Back pressure at port 3 (tank) is directly additive to the valve setting at a 1:1 ratio.
■ Note: This valve deviates from Sun's normal flow path for four port relief valves; port 2 is the inlet,
port 1 is the system, port 3 is tank and port 4 is vent. Therefore, it is probably not useable in existing
standard Sun relief manifolds.

HV C A – L A N
Nominal
Capacity
Adjustment
B 75 - 1500 psi +$ 0.00 V Viton
C Tamper Resistant
Factory Set D 75 - 800 psi
K Handknob +$ 5.00 W 75 - 4500 psi

Hybrid Valves
VENTABLE, PILOT OPERATED, BALANCED PISTON, RELIEF VALVE - BEFORE
CHECK WITH INTEGRAL PILOT CONTROL CAVITY
b into the end of the relief cartridge via the T-8A cavity. These pilot control
3 cartridges are sold separately and include electro-proportional, solenoid, air
4
c T-8A
Port
2 4
3
Port Locating
a
2
10 GPM HVCA – 8DN T - 21A 1.38 7/8 1.78 30/35
Port
1 Port
Performance Curves
HVCA-8
4000 300
3000
P = psi
P = psi
200
2000
100
1000 Mimimum
Setting
0 5 10 15 0 5 10 15

■ Maximum valve leakage (port 2 to port 3) = 2 in³/min. at 1000 psi
■ Minimum setting is 75 psi for all spring ranges.
■ Back pressure at port 4 (tank) is directly additive to the valve setting at a 1:1 ratio.
■ Note: This valve deviates from Sun's normal flow path for four port relief valves; port 2 is the inlet,
port 1 is the system, port 3 is tank and port 4 is vent. Therefore, it is probably not useable in existing
standard Sun relief manifolds.

HV C A – 8 D N
Capacity
C 10 GPM $ 85.00 8 with T-8A cavity +$ 0.00 D 75 psi +$ 0.00 N Buna-N
in hex body for
(see pilot control
section for alternate
options)
Hybrid Valves
NOTES

General Information
Page
Cartridge Control Options 162
Cartridge Control Kits 163
Cavity Plugs 165 3
Solenoid Electrical Connector Options 167
Orifice Pressure Drop Data 168

Cartridge Control Options
General Purpose Controls (for use in systems where adjustment may be changed after installation.)
L Standard Screw Adjustment Key Lock Kit
5/32" Hex
O-ring seal on adjust screw. Adjust Optional adjustment Key Lock Cover Kit for L controls allows
screw positively retained. Overset adjustment to be locked with a key to prevent unauthorized
protection-pilot spring cannot go solid. changes in valve setting. Adjustment is easily accessible when lock
assembly is removed. 2.44"
Requires replacement of
9/16" Hex standard locknut with special 1.66"
locknut which accepts lock
assembly, and a new wire
stop ring for overset
K Handknob with Lock Knob 3.12"
protection.
to remove key or cover
Handknob and lock knob added to L
control. Sun handknob kits for field
conversion are available.
5/32" Hex
H Calibrated Handknob with Detent Lock
Fully calibrated handknob for flow control cartridges.
40 radial calibrations per turn. Moveable zero indicator. (Minor
disassembly required.) Rising detented locking collar positively
locks adjustment knob against vibration or accidental tampering.
Any desired setting may be recorded and repeated. U.S. Patent
O Handknob with Panel Mount #4,577,831.
1.17"
Special threaded cartridge hex body diameter
1.25" diameter
Zero Indicator
with panel nut for mounting cartridge
through access hole in control panel.
Handknob and lock knob included.
Panel Hole: Panel Dia.
Hole
Series 1 cartridges .75” dia. 9/16" Hex
Series 2 cartridges 1.00” dia.
.09"
Panel nut hex size identical to cartridge .30" Locking Collar
Rising Stem
hex size. Counts Full Turns
Diameter 1.13” Dia. 1.38” Dia. 1.62” Dia. 1.62” Dia.

Series 1 2 3 4
NCCB NCEB NCFB NCGB
C Tamper Resistant Factory Set NCCC NCEC NCFC NCGC
Cover press-fit onto L control cartridge NFCC NFDC NFEC NFFC
shoulder. Valves may be ordered in this NFCD NFDD NFED NFFD
configuration from Sun. Specify FDBA FDCB FDEA FDFA
pressure setting on order. Setting
stamped on cartridge hex. Sun kits for
field conversion are available.
Special Purpose Controls (for use in systems where adjustment is seldom changed after installation)
5/32" Hex
J Socket Head Set Screw with Cap 5/32"
(4 mm)Hex F Wrench Adjustment
Stem seal - Seal under locknut.
Adjustment screw not retained. No Stem seal - Seal under locknut.
overset protection. Adjusting screw is not retained.
Overset protection-pilot spring cannot
go solid.
9/16"
9/16" Hex
Hex
(14,3 mm)
Counterbalance Cartridge Controls
All Sun counterbalance cartridges are built with a leakproof adjustment - O-ring seals are on the adjusting screw-but are not designed for frequent
adjustment in the field. Cartridges that are factory pre-set by Sun to a customer specified pressure setting are available and can be installed directly
on a machine without the need for further adjustment.
C Tamper Resistant Factory Set L Standard Leakproof

See “C” Control description above. Screw Adjustment. Series 1, 2, 3: 5/32" Hex
Series 4: 7/32" Hex
O-ring seal on adjust
screw.
Series 1, 2, 3: 9/16" Hex

Series 4: 3/4" Hex
Cartridge Control Kits
Service Kit Use specifically with
Number Control/Cartridge Price Description Notes
Description
Locknut
Adjustment Adjust
Screw Kit All F controls Screw Seal
991-006 To assure a complete seal on the
Cap Seal stem - release all pressure on the
cartridge after setting. Then...
Adjustment tighten locknut (and cap, on J).
Screw Kit All J controls Adjust
Locknut Screw
991-010
Tamper For all Sun cartridges with L
Resistant Cover adjustment
991-000 Series 0 - 3/4” hex 1. Adjust valve to desired setting
and tighten locknut.
991-004 Series 1 - 7/8” hex 2. Using an arbor press or a soft
991-001 Series 2 - 1 1/8” hex Cover hammer, install cover until it
991-002 Series 3 - 1 1/4” hex seats on cartridge hex.
991-003 Series 4 - 1 5/8” hex 3. Cover is a press fit on cartridge
991-032 Series 1 - 7/8” hex (CB**, CC**) shoulder.
991-033 Series 2 - 1 1/8” hex (CB**, CC**)
Lock
1. Remove original wire stop ring
Assembly
Adapter
Locknut and locknut.
2. Thread on the adapter locknut
Key Lock Kit For all Sun cartridges with L and install new wire stop ring
993-008
adjustment (except Series 0 and through slot provided.
counterbalance cartridges). 3. Adjust valve to desired setting
and tighten adapter locknut.
Key Wire Stop Ring 4. Slide lock assembly over
adapter, lock and remove key.
Install while cartridge is screwed in 1. Do not remove stop ring.
cavity to prevent damage. 2. Install lock knob by snapping
onto the locknut.
3. Install star knob until contact is
5 made with the stop ring.
6 4. Caution during installation on
1
flow control valves (that have
1 no stop ring). Make sure valve
Maximum can be shut with hand knob
.750
higher than installed.
L adjustment 5. Insert pins in cover so that they
Three-winged For all Series 1, 2, 3, 4 project on backside.
Handknob Kit valves with L or O 6. Put cover on with inserted pins
991-034 adjustment except and drive pins in until flush
counterbalance cartridges. with cover.
When knob is used as a maximum
2.43diameter Setting Limiter:
62 mm
1. Set valve at desired maximum
.90 setting.
23 mm 2. Tighten lock nut
The handknob can be used
as a Maximum Setting Limiter. (110 lbs. inch).
3. Remove stop ring.
4. Install lock knob.
5. Install handknob until flush
with the lock knob.
2.43diameter
Three-winged 62 mm
Handknob Kit This kit should be used in .90
with 23 mm Follow installation instructions
1 3/8” dia. applications where there is high $ 9.80
vibration and a plastic lock knob described above.
aluminum lock
knob. may loosen.
991-039 Aluminum
Lock Knob
Cartridge Control Kits continue on next page
Cartridge Control Kits
Service Kit Use specifically with
Number Control/Cartridge Price Description Notes
Description
Use this kit to adapt all L
K controls to K controls (except
Handknob Kit
991-211 Series 0 and counterbalance
cartridges).
991-222 K control for Series 0 Only cartridges date stamped
Handknob Lock
Assembly “41” or later and originally
Panel O controls Knob
supplied with plastic knobs. Lock
Handknob Kit All Series 1 cartridges knob snaps onto locknut
991-215 7/8” hex M20 thread furnished on cartridge.
Panel O controls
All Series 2 cartridges
Handknob Kit Handknob Lock Panel Nut
991-216 1 1/8” hex Assembly Knob
1”-14 thread
H H controls
Calibrated
All series of flow controls
Handknob Kit Only for cartridges originally
FDCB , NCEB, NCEC , supplied with an H handknob.
991-219 Valves can not be modified in the
NFDC, NFDD only
field.
FDEA , FDFA, NCFB, NCFC,
991-220
NCGB, NCGC, NFEC, Note: The H control is
NFED, NFFC, Exsisting Only available for the cartridges
NFFD only Handknob Lockring O-ring Cartridge shown to the left.
991-221 FDBA , NCCB , NCCC ,
NFCC, NFDC only
Lockwire Kit All M, Q and R controls Locking Wire

Lead Seal
(except solenoid operated
991-012 cartridges).
Adjustment
Screw Kit CKCA L**CKCD L** Manual
Release
991-112-003 Viton CKCB L**CPCA L** Screw
Back-up
Ring
CKCC L**
991-112-007 Buna-N
$ 2.10
Only cartridges date stamped “62”
or earlier.
Adjustment
Screw Kit CKEA L**CKED L**
991-212-003 Viton CKEB L**CPEA L** Seal
CKEC L** Locknut
991-212-007 Buna-N
Cavity Plugs
It is sometimes desirable to remove a Sun cartridge valve and still maintain the integrity of
the hydraulic system. This may be necessitated by the need to flush a system after repairs
or a piping change, or to change an operating function in the circuit. For these
requirements, Sun offers two styles of cavity plugs - all ports blocked and main ports open
to flow.
Plugs for Two Port Cavities:
All Ports Open All Ports Blocked

Cavity Plug Cavity Plug
Series Cavity
Model Code* Buna-N Viton Model Code Buna-N Viton
P T-8A XAOA-XX* $ 8.00 $ 10.00 XACA-XX*
0 T-162A XZOA-XX* XZCB-XX*
2
T-10A XFCA-XX* 2
1 XFOA-XX*
T-13A XGCA-XX*
T-3A XCCA-XX*
2 XCOA-XX*
1 T-5A XDCA-XX* 1
3 T-16A XIOA-XX* $ 18.00 $ 20.00 XICA-XX*

4 T-18A XKOA-XX* XKCA-XX*
Plugs for Three Port Cavities
Ports 1 to 2 Open
All Ports Blocked
Port 3 Blocked
Series Cavity Cavity Plug Cavity Plug
3 Model Code* Buna-N Viton Model Code Buna-N Viton 3
P T-9A XAOB-XX* $ 14.00 $ 17.00 XACBXX*
2 0 T-163A XZOB-XX* XZCB-XX* 2

1 T-11A XEOA-XX* $ 12.00 $ 15.00 XECA-XX*
2 T-2A XBOA-XX* XBCA-XX*
1 3 T-17A XHOA-XX* $ 20.00 $ 23.00 XHCA-XX*
1
4 T-19A XJOA-XX* XJCA-XX*
Plugs for Four Port Cavities (Internal Locating Shoulder)
Ports 1 to 2 Open
All Ports Blocked
Port 3 and 4 Blocked
4 4
Series Cavity Cavity Plug Cavity Plug
Model Code* Buna-N Viton Model Code Buna-N Viton
3 3
1 T-21A XMOA-XX* $15.00 $19.00 XMCA-XX*
2 2 T-22A XNOA-XX* XNCA-XX* 2
3 T-23A XPOA-XX* $26.00 $30.00 XPCA-XX*
1 4 T-24A XQOA-XX* XQCA-XX* 1
*Insert in the seventh position model code digit N to order Buna-N seals or V to order Viton seals.
Cavity Plugs
Plugs for Four Port Cavities (External Locating Shoulder)
All Ports Open All Ports Blocked

4 4
Series Cavity Model Model
Buna-N Viton Buna-N Viton
3 Code* Code* 3
1 T-31A XFOA-XX* $ 10.00 $14.00 XRCA-XX*
2 2 T-32A XCOA-XX* XSCA-XX* 2
3 T-33A XIOA-XX* $ 18.00 $22.00 XTCA-XX*
4 T-34A XKOA-XX* XVCA-XX*
1 1
Plugs for Six Port Cavities
6 Ports 1, 2, 3 and 4 Open 6

All Ports Blocked
5 Ports 5 and 6 Blocked 5
Series Cavity Model Buna-N Viton Model Buna-N Viton
4 Code* Code* 4
1 T-61A XMOA-XX* $15.00 $21.00 XRCC-XX*
3 3
2 T-62A XNOA-XX* XSCC-XX*
2 3 T-63A XPOA-XX* $26.00 $32.00 XTCC-XX* 2

4 T-64A XQOA-XX* XVCC-XX*
1 1
Cavity Adaptor (Converts Waterman 12-2 Cavity to the Sun T-8A Cavity)
All Ports Open

Cavity Plug
Cavity Model
Buna-N Viton
2 Code*
12-2 XAAA-8X*
Sun Solenoid Electrical Connector Options
Sun Hydraulics has a range of pilot flow and full flow solenoid products with operating pressures up to 5000 psi. These products
are available with the coil configuration options shown below. If you only require pilot flow and want to operate these packages
in a 5000 psi system, Sun offers a screw-in adapter that converts the Waterman 12-2 cavity to a Sun T-8A cavity.
Connector Options for Sun Pilot Flow Solenoid Valves (DAAA, DBAA)
ISO / DIN 43650 SAE J858-A Twin Lead
Description Coil only part number Coil only part number Coil only part number
115 V AC
50/60 Hz 760-211 $28.00 N/A N/A
230 V AC
50/60 Hz 760-223 N/A N/A
6 V DC 760-206 $22.40 760-506 $20.20 760-706
12 V DC 760-212 760-512 760-712
24 V DC 760-224 $22.40 760-524 $20.20 760-724
28 V DC 760-228 760-528 760-728
36 V DC 760-236 $22.40 760-536 $20.20 760-736
48 V DC 760-248 760-548 760-748
Connector Options for Sun Full Flow Solenoid Valves (DLDA, DTDA, DMDA, DNDA) and Proportional Valves (RBAP, PRDP, PRDL)
ISO/DIN 43650 Twin Spade AMP® Junior Timer Twin Lead Metri-Pack Deutsch
(SAE J858A)
Coil only part Coil only part Coil only part Coil only part Coil only part Coil only part
Description number number number number number number
115 V AC
50/60 Hz 770-211 $23.50 N/A N/A N/A N/A N/A
230 V AC
50/60 Hz 770-223 N/A N/A N/A N/A N/A
12 V DC 770-212 $15.50 770-512 $17.10 770-612 $15.00 770-712 $17.10 770-812 $19.00 770-912
24 V DC 770-224 770-524 770-624 770-724 770-824 770-924
48VDC* 770-248* $15.50 770-548* $17.10 770-648* $15.00 770-748* $17.10 770-848* $19.00 770-948*
General Information
ORIFICE PRESSURE DROP DATA
No allowance has been made for viscosity effects, or regain of pressure downstream.
Orifice diameter, inches

1 1 1
64 32 16
4000
3
32
3000
2500
2000
Pressure Drop psi
1500
1
1000 8
500
5
32
200 3
16
These charts are based on
7
the formula: 100
32
1
Q = C x A x 2 gH 50
4
25 5
Where: 10 16
Q = Flow in Cu. Ft. per Sec. 3
0 8
C = Orifice Coefficient
1 2 3 4 5 6 7 8 9 10 7
A = Area of Orifice in Sq. Ft. 1
16
H = Pressure Head in Ft. Flow GPM 2
Specify Gravity of Fluid = .895

This equation becomes
Q(GPM) = 24.12 x A(sq.in.) x Pressure Drop (psi) when C = 0.6
Orifice diameter, inches
3 1 5 3 7 1
32 8 32 16 32 4
4000
3000 5
16
2500
2000
1500
Pressure Drop psi
3
8
1000
7
16
500
1
2
9
200 16
5
100 8
3
50 4
25 7
8
10 1
0
10 20 30 40 50 60 70 80 90 100
Flow GPM

Model Code Index
Model Code Cavity Page Model Code Cavity Page Model Code Cavity Page
CACA - ✱✱✱ T-11A 55 CBGL - ✱✱✱ T-17A 49 COJA - ✱✱✱ T-19A 147
CACG - ✱✱✱ T-11A 55 CBGY - ✱✱✱ T-17A 48 CSAA - ✱✱✱ T-13A 136
CACK - ✱✱✱ T-11A 55 CBHA - ✱✱✱ T-19A 53 CSAB - ✱✱✱ T-11A 137
CACL - ✱✱✱ T-11A 55 CBHG - ✱✱✱ T-19A 53 CSAC - ✱✱✱ T-13A 136
CAEA - ✱✱✱ T-2A 55 CBIA - ✱✱✱ T-19A 48 CSAD - ✱✱✱ T-11A 137
CAEG - ✱✱✱ T-2A 55 CBIB - ✱✱✱ T-19A 48 CSAW - ✱✱✱ T-162A 136
CAEK - ✱✱✱ T-2A 55 CBIG - ✱✱✱ T-19A 49 CSAX - ✱✱✱ T-163A 137
CAEL - ✱✱✱ T-2A 55 CBIH - ✱✱✱ T-19A 49 CSAY - ✱✱✱ T-162A 136
CAGA - ✱✱✱ T-17A 55 CBIL - ✱✱✱ T-19A 49 CSAZ - ✱✱✱ T-163A 137
CAGG - ✱✱✱ T-17A 55 CBIY - ✱✱✱ T-19A 48 CVCV - ✱✱✱ T-21A 46
CAGK - ✱✱✱ T-17A 55 CCCA - ✱✱✱ T-11A 54 CVEV - ✱✱✱ T-22A 46
CAGL - ✱✱✱ T-17A 55 CCEA - ✱✱✱ T-2A 54 CVGV - ✱✱✱ T-23A 46
CAIA - ✱✱✱ T-19A 55 CCGA - ✱✱✱ T-17A 54 CVIV - ✱✱✱ T-24A 46
CAIG - ✱✱✱ T-19A 55 CCIA - ✱✱✱ T-19A 54 CWCA- ✱✱✱ T-21A 56
CAIK - ✱✱✱ T-19A 55 CDAA - ✱✱✱ T-13A 138 CWCG- ✱✱✱ T-21A 57
CAIL - ✱✱✱ T-19A 55 CDAB - ✱✱✱ T-11A 139 CWCK- ✱✱✱ T-21A 56
CBBA - ✱✱✱ T-11A 52 CDAC - ✱✱✱ T-13A 138 CWCL - ✱✱✱ T-21A 57
CBBB - ✱✱✱ T-11A 50 CDAD - ✱✱✱ T-11A 139 CWEA - ✱✱✱ T-22A 56
CBBC - ✱✱✱ T-11A 50 CKBB - ✱✱✱ T-163A 44 CWEG- ✱✱✱ T-22A 57
CBBD - ✱✱✱ T-11A 51 CKBD - ✱✱✱ T-163A 44 CWEK - ✱✱✱ T-22A 56
CBBG - ✱✱✱ T-11A 53 CKCB - ✱✱✱ T-11A 44 CWEL - ✱✱✱ T-22A 57
CBBL - ✱✱✱ T-11A 51 CKCD - ✱✱✱ T-11A 44 CWGA- ✱✱✱ T-23A 56
CBBY - ✱✱✱ T-11A 52 CKCV - ✱✱✱ T-11A 45 CWGG- ✱✱✱ T-23A 57
CBCA - ✱✱✱ T-11A 48 CKEB - ✱✱✱ T-2A 44 CWGK- ✱✱✱ T-23A 56
CBCB - ✱✱✱ T-11A 48 CKED - ✱✱✱ T-2A 44 CWGL - ✱✱✱ T-23A 57
CBCG - ✱✱✱ T-11A 49 CKEV - ✱✱✱ T-2A 45 CWIA - ✱✱✱ T-24A 56
CBCH - ✱✱✱ T-11A 49 CKGB - ✱✱✱ T-17A 44 CWIG - ✱✱✱ T-24A 57
CBCL - ✱✱✱ T-11A 49 CKGD - ✱✱✱ T-17A 44 CWIK - ✱✱✱ T-24A 56
CBCY - ✱✱✱ T-11A 48 CKGV - ✱✱✱ T-17A 45 CWIL - ✱✱✱ T-24A 57
CBDA - ✱✱✱ T-2A 52 CKIB - ✱✱✱ T-19A 44 CXAD - ✱✱✱ T-162A 61
CBDB - ✱✱✱ T-2A 50 CKID - ✱✱✱ T-19A 44 CXBA - ✱✱✱ T-162A 60
CBDC - ✱✱✱ T-2A 50 CKIV - ✱✱✱ T-19A 45 CXCD - ✱✱✱ T-13A 61
CBDD - ✱✱✱ T-2A 51 CNAC - ✱✱✱ T-162A 72 CXCE - ✱✱✱ T-11A 62
CBDG - ✱✱✱ T-2A 53 CNBC - ✱✱✱ T-162A 63 CXDA - ✱✱✱ T-13A 60
CBDL - ✱✱✱ T-2A 51 CNCC - ✱✱✱ T-13A 72 CXED - ✱✱✱ T-5A 61
CBEA - ✱✱✱ T-2A 48 CNCD - ✱✱✱ T-11A 64 CXEE - ✱✱✱ T-2A 62
CBEB - ✱✱✱ T-2A 48 CNDC - ✱✱✱ T-13A 63 CXFA - ✱✱✱ T-5A 60
CBEG - ✱✱✱ T-2A 49 CNEC - ✱✱✱ T-5A 72 CXGD - ✱✱✱ T-16A 61
CBEH - ✱✱✱ T-2A 49 CNED - ✱✱✱ T-2A 64 CXGE - ✱✱✱ T-17A 62
CBEL - ✱✱✱ T-2A 49 CNFC - ✱✱✱ T-5A 63 CXHA - ✱✱✱ T-16A 60
CBEY - ✱✱✱ T-2A 48 CNGC - ✱✱✱ T-16A 72 CXID - ✱✱✱ T-18A 61
CBFA - ✱✱✱ T-17A 52 CNGD - ✱✱✱ T-17A 64 CXIE - ✱✱✱ T-19A 62
CBFB - ✱✱✱ T-17A 50 CNHC - ✱✱✱ T-16A 63 CXJA - ✱✱✱ T-18A 60
CBFC - ✱✱✱ T-17A 50 CNIC - ✱✱✱ T-18A 72 DAAA - ✱✱✱ T-8A 118
CBFD - ✱✱✱ T-17A 51 CNID - ✱✱✱ T-19A 64 DAAA - ✱✱✱ T-8A 122
CBFG - ✱✱✱ T-17A 53 CNJC - ✱✱✱ T-18A 63 DAAC - ✱✱✱ T-8A 118
CBFL - ✱✱✱ T-17A 51 COBA - ✱✱✱ T-163A 147 DAAC - ✱✱✱ T-8A 122
CBGA - ✱✱✱ T-17A 48 CODA - ✱✱✱ T-11A 147 DAAH - ✱✱✱ T-8A 123
CBGB - ✱✱✱ T-17A 48 COFA - ✱✱✱ T-2A 147 DAAP - ✱✱✱ T-8A 124
CBGG - ✱✱✱ T-17A 49 COFO - ✱✱✱ T-2A 146 DAAM - ✱✱✱ T-8A 125
CBGH - ✱✱✱ T-17A 49 COHA - ✱✱✱ T-17A 147 DBAA - ✱✱✱ T-9A 119

Model Code Index
DBAA - ✱✱✱ T-9A 126 DOJP - ✱✱✱ T-24A 96 DVBM - 8✱✱ T-21A 107
DBAC - ✱✱✱ T-9A 119 DOJR - ✱✱✱ T-24A 94 DVBN - 8✱✱ T-21A 107
DBAC - ✱✱✱ T-9A 126 DOJR - 8✱✱ T-24A 95 DVBO - 8✱✱ T-21A 107
DBAH - ✱✱✱ T-9A 127 DOJS - ✱✱✱ T-24A 93 DVBP - 8✱✱ T-21A 107
DBAM - ✱✱✱ T-9 122 DPBA - ✱✱✱ T-11A 102 FCBB - ✱✱✱ T-162A 70
DBAP - ✱✱✱ T-9A 128 DPBB - ✱✱✱ T-11A 102 FCCB - ✱✱✱ T-13A 70
DCCC - ✱✱✱ T-61A 110 DPBC - ✱✱✱ T-11A 102 FCDB - ✱✱✱ T-5A 70
DCCD - ✱✱✱ T-61A 111 DPBD - ✱✱✱ T-11A 102 FCEB - ✱✱✱ T-16A 70
DCDC - ✱✱✱ T-62A 110 DPBM - ✱✱✱ T-21A 103 FCFB - ✱✱✱ T-18A 70
DCDD - ✱✱✱ T-62A 111 DPBN - ✱✱✱ T-21A 103 FDBA - ✱✱✱ T-13A 71
DCEC - ✱✱✱ T-63A 110 DPBO - ✱✱✱ T-21A 103 FDCB - ✱✱✱ T-5A 71
DCED - ✱✱✱ T-63A 111 DPBP - ✱✱✱ T-21A 103 FDEA - ✱✱✱ T-16A 71
DCFC - ✱✱✱ T-64A 110 DPCA - ✱✱✱ T-2A 102 FDFA - ✱✱✱ T-18A 71
DCFD - ✱✱✱ T-64A 111 DPCB - ✱✱✱ T-2A 102 FPCC - ✱✱✱ T-13A 73
DFCA - 8✱✱ T-13A 108 DPCC - ✱✱✱ T-2A 102 FPCH - ✱✱✱ T-13A 74
DFCB - 8✱✱ T-13A 109 DPCD - ✱✱✱ T-2A 102 FQCA - ✱✱✱ T-13A 144
DFDA - 8✱✱ T-5A 108 DPCM - ✱✱✱ T-22A 103 FQEA - ✱✱✱ T-5A 144
DFDB - 8✱✱ T-5A 109 DPCN - ✱✱✱ T-22A 103 FQGA - ✱✱✱ T-16A 144
DFEA - 8✱✱ T-16A 108 DPCO - ✱✱✱ T-22A 103 FQIA - ✱✱✱ T-18A 144
DFEB - 8✱✱ T-16A 109 DPCP - ✱✱✱ T-22A 103 FRBA - ✱✱✱ T-163A 76
DFFA - 8✱✱ T-18A 108 DRAX - ✱✱✱ T-21A 150 FRCA - ✱✱✱ T-11A 76
DKDP - ✱✱✱ T-21A 98 DRAY - ✱✱✱ T-21A 151 FRDA - ✱✱✱ T-2A 76
DKDR - ✱✱✱ T-21A 99 DRBA - ✱✱✱ T-11A 104 FREA - ✱✱✱ T-17A 76
DKDR - 8✱✱ T-21A 100 DRBB - ✱✱✱ T-11A 104 FRFA - ✱✱✱ T-19A 76
DKDS - ✱✱✱ T-21A 97 DRBC - ✱✱✱ T-11A 104 FSBA - ✱✱✱ T-31A 83
DKFP - ✱✱✱ T-22A 98 DRBD - ✱✱✱ T-11A 104 FSBD - ✱✱✱ T-31A 82
DKFR - ✱✱✱ T-22A 99 DRBR - ✱✱✱ T-21A 105 FSBS - ✱✱✱ T-31A 84
DKFR - 8✱✱ T-22A 100 DSCH - ✱✱✱ T-31A 140 FSCA - ✱✱✱ T-31A 83
DKFS - ✱✱✱ T-22A 97 DSCO - ✱✱✱ T-31A 142 FSCD - ✱✱✱ T-31A 82
DKHP - ✱✱✱ T-23A 98 DSCS - ✱✱✱ T-31A 141 FSCH - ✱✱✱ T-31A 85
DKHR - ✱✱✱ T-23A 99 DSCX - ✱✱✱ T-31A 152 FSCS - ✱✱✱ T-31A 84
DKHR - 8✱✱ T-23A 100 DSCY - ✱✱✱ T-31A 153 FSDA - ✱✱✱ T-32A 83
DKHS - ✱✱✱ T-23A 97 DSEH - ✱✱✱ T-32A 140 FSDD - ✱✱✱ T-32A 82
DKJP - ✱✱✱ T-24A 98 DSEO - ✱✱✱ T-32A 142 FSDH - ✱✱✱ T-32A 85
DKJR - ✱✱✱ T-24A 99 DSES - ✱✱✱ T-32A 141 FSDS - ✱✱✱ T-32A 84
DKJR - 8✱✱ T-24A 100 DSEX - ✱✱✱ T-32A 152 FSEA - ✱✱✱ T-33A 83
DKJS - ✱✱✱ T-24A 97 DSEY - ✱✱✱ T-32A 153 FSED - ✱✱✱ T-33A 82
DLDA - ✱✱✱ T-13A 114 DSGH - ✱✱✱ T-33A 140 FSEH - ✱✱✱ T-33A 85
DMDA - ✱✱✱ T-11A 116 DSGO - ✱✱✱ T-33A 142 FSES - ✱✱✱ T-33A 84
DNDA - ✱✱✱ T-31A 117 DSGS - ✱✱✱ T-33A 141 FSFA - ✱✱✱ T-34A 83
DODP - ✱✱✱ T-21A 96 DSGX - ✱✱✱ T-33A 152 FSFD - ✱✱✱ T-34A 82
DODR - ✱✱✱ T-21A 94 DSGY - ✱✱✱ T-33A 153 FSFH - ✱✱✱ T-34A 85
DODR - 8✱✱ T-21A 95 DSIH - ✱✱✱ T-34A 140 FSFS - ✱✱✱ T-34A 84
DODS - ✱✱✱ T-21A 93 DSIO - ✱✱✱ T-34A 142 FVCA - ✱✱✱ T-21A 77
DOFP - ✱✱✱ T-22A 96 DSIS - ✱✱✱ T-34A 141 FVCA - 8✱✱ T-21A 78
DOFR - ✱✱✱ T-22A 94 DSIX - ✱✱✱ T-34A 152 FVDA - ✱✱✱ T-22A 77
DOFR - 8✱✱ T-22A 95 DSIY - ✱✱✱ T-34A 153 FVDA - 8✱✱ T-22A 78
DOFS - ✱✱✱ T-22A 93 DTDA - ✱✱✱ T-13A 115 FVEA - ✱✱✱ T-23A 77
DOHP - ✱✱✱ T-23A 96 DVBA - 8✱✱ T-11A 106 FVEA - 8✱✱ T-23A 78
DOHR - ✱✱✱ T-23A 94 DVBB - 8✱✱ T-11A 106 FVFA - ✱✱✱ T-24A 77
DOHR - 8✱✱ T-23A 95 DVBC - 8✱✱ T-11A 106 FVFA - 8✱✱ T-24A 78
DOHS - ✱✱✱ T-23A 93 DVBD - 8✱✱ T-11A 106 FXBA - ✱✱✱ T-162A 69

Model Code Index
CARTRIDGES
FXCA - ✱✱✱ T-13A 69 LPBC - ✱✱✱ T-163A 91 PPDB - 8✱✱ T-11A 38
FXDA - ✱✱✱ T-5A 69 LPDA - ✱✱✱ T-11A 91 PPFB - ✱✱✱ T-2A 31
FXEA - ✱✱✱ T-16A 69 LPDC - ✱✱✱ T-11A 91 PPFB - 8✱✱ T-2A 38
FXFA - ✱✱✱ T-18A 69 LPFA - ✱✱✱ T-2A 91 PPFC - ✱✱✱ T-2A 36
HRDA - ✱✱✱ T-11A 156 LPFC - ✱✱✱ T-2A 91 PPHB - ✱✱✱ T-17A 31
HRDB - ✱✱✱ T-11A 157 LPHA - ✱✱✱ T-17A 91 PPHB - 8✱✱ T-17A 38
HVCA - ✱✱✱ T-21A 158 LPHC - ✱✱✱ T-17A 91 PPHC - ✱✱✱ T-17A 36
HVCA - 8✱✱ T-21A 159 LPJA - ✱✱✱ T-19A 91 PPJB - ✱✱✱ T-19A 31
LHDA - ✱✱✱ T-31A 79 LPJC - ✱✱✱ T-19A 91 PPJB - 8✱✱ T-19A 38
LHDT - ✱✱✱ T-31A 154 LRBA - ✱✱✱ T-163A 92 PPJC - ✱✱✱ T-19A 36
LHFA - ✱✱✱ T-32A 79 LRBC - ✱✱✱ T-163A 92 PRDB - ✱✱✱ T-11A 32
LHFT - ✱✱✱ T-32A 154 LRDA - ✱✱✱ T-11A 92 PRDL - ✱✱✱ T-11A 40
LHHA - ✱✱✱ T-33A 79 LRDC - ✱✱✱ T-11A 92 PRDP - ✱✱✱ T-11A 41
LHHT - ✱✱✱ T-33A 154 LRFA - ✱✱✱ T-2A 92 PRFB - ✱✱✱ T-2A 32
LHJA - ✱✱✱ T-34A 79 LRFC - ✱✱✱ T-2A 92 PRHB - ✱✱✱ T-17A 32
LKDC - ✱✱✱ T-11A 90 LRHA - ✱✱✱ T-17A 92 PRJB - ✱✱✱ T-19A 32
LKFC - ✱✱✱ T-2A 90 LRHC - ✱✱✱ T-17A 92 PVDA - ✱✱✱ T-21A 33
LKHC - ✱✱✱ T-17A 90 LRJA - ✱✱✱ T-19A 92 PVDA - 8✱✱ T-21A 39
LKJC - ✱✱✱ T-19A 90 LRJC - ✱✱✱ T-19A 92 PVDB - ✱✱✱ T-21A 34
LODA - ✱✱✱ T-11A 88 NCBB - ✱✱✱ T-162A 68 PVFA - ✱✱✱ T-22A 33
LODA - 8✱✱ T-11A 89 NCCC - ✱✱✱ T-13A 68 PVFA - 8✱✱ T-22A 39
LODB - ✱✱✱ T-11A 88 NCEB - ✱✱✱ T-5A 68 PVFB - ✱✱✱ T-22A 34
LODB - 8✱✱ T-11A 89 NCCB - ✱✱✱ T-13A 68 PVHA - ✱✱✱ T-23A 33
LODC - 8✱✱ T-11A 88 NCEC - ✱✱✱ T-5A 68 PVHA - 8✱✱ T-23A 39
LODD - ✱✱✱ T-11A 88 NCFB - ✱✱✱ T-16A 68 PVHB - ✱✱✱ T-23A 34
LODD - 8✱✱ T-11A 89 NCFC - ✱✱✱ T-16A 68 PVJA - ✱✱✱ T-24A 33
LODO - ✱✱✱ T-11A 88 NCGB - ✱✱✱ T-18A 68 PVJA - 8✱✱ T-24A 39
LOFA - ✱✱✱ T-2A 88 NCGC - ✱✱✱ T-18A 68 PVJB - ✱✱✱ T-24A 34
LOFA - 8✱✱ T-2A 89 NFAB - ✱✱✱ T-8A 132 QCDA - ✱✱✱ T-21A 149
LOFB - ✱✱✱ T-2A 88 NFBC - ✱✱✱ T-162A 66 QCDB - ✱✱✱ T-21A 149
LOFB - 8✱✱ T-2A 89 NFCC - ✱✱✱ T-13A 66 QCDC - ✱✱✱ T-21A 149
LOFC - ✱✱✱ T-2A 88 NFCD - ✱✱✱ T-13A 67 QCDD - ✱✱✱ T-21A 149
LOFD - ✱✱✱ T-2A 88 NFDC - ✱✱✱ T-5A 66 QCDD - ✱✱✱ T-21A 149
LOFD - 8✱✱ T-2A 89 NFDD - ✱✱✱ T-5A 67 QPAA - ✱✱✱ T-11A 148
LOFO - ✱✱✱ T-2A 88 NFEC - ✱✱✱ T-16A 66 QPAB - ✱✱✱ T-11A 148
LOHA - ✱✱✱ T-17A 88 NFED - ✱✱✱ T-16A 67 QPAC - ✱✱✱ T-11A 148
LOHA - 8✱✱ T-17A 89 NFFC - ✱✱✱ T-18A 66 QPAD - ✱✱✱ T-11A 148
LOHB - ✱✱✱ T-17A 88 NFFD - ✱✱✱ T-18A 67 RBAA - ✱✱✱ T-3A 8
LOHB - 8✱✱ T-17A 89 NQEB - ✱✱✱ T-3A 145 RBAC - ✱✱✱ T-10A 8
LOHC - ✱✱✱ T-17A 88 PBBB - ✱✱✱ T-163A 30 RBAE - ✱✱✱ T-8A 130
LOHD - ✱✱✱ T-17A 88 PBDB - ✱✱✱ T-11A 30 RBAP - ✱✱✱ T-8A 13
LOHD - 8✱✱ T-17A 89 PBDB - 8✱✱ T-11A 37 RBAP - ✱✱✱ T-8A 133
LOHO - ✱✱✱ T-17A 88 PBFB - ✱✱✱ T-2A 30 RBAR - ✱✱✱ T-8A 131
LOJA - ✱✱✱ T-19A 88 PBFB - 8✱✱ T-2A 37 RDBA - ✱✱✱ T-162A 7
LOJA - 8✱✱ T-19A 89 PBFC - ✱✱✱ T-2A 35 RDDA - ✱✱✱ T-10A 7
LOJB - ✱✱✱ T-19A 88 PBHB - ✱✱✱ T-17A 30 RDFA - ✱✱✱ T-3A 7
LOJB - 8✱✱ T-19A 89 PBHB - 8✱✱ T-17A 37 RDHA - ✱✱✱ T-16A 7
LOJC - ✱✱✱ T-19A 88 PBHC - ✱✱✱ T-17A 35 RDJA - ✱✱✱ T-18A 7
LOJD - ✱✱✱ T-19A 88 PBJB - ✱✱✱ T-19A 30 RPCC - ✱✱✱ T-162A 6
LOJD - 8✱✱ T-19A 89 PBJB - 8✱✱ T-19A 37 RPCC - 8✱✱ T-162A 14
LOJO - ✱✱✱ T-19A 88 PBJC - ✱✱✱ T-19A 35 RPEC - ✱✱✱ T-10A 6
LPBA - ✱✱✱ T-163A 91 PPDB - ✱✱✱ T-11A 31 RPEC - 8✱✱ T-10A 14

Model Code Index
RPGC - ✱✱✱ T-3A 6 RSFC - 8✱✱ T-2A 23 RVGA - ✱✱✱ T-17A 16
RPGC - 8✱✱ T-3A 14 RSFE - ✱✱✱ T-2A 24 RVGB - ✱✱✱ T-17A 17
RPGD - ✱✱✱ T-3A 12 RSHC - ✱✱✱ T-17A 22 RVGD - ✱✱✱ T-23A 19
RPGS - ✱✱✱ T-3A 15 RSHC - 8✱✱ T-17A 23 RVGD - 8✱✱ T-23A 20
RPGT - ✱✱✱ T-3A 10 RSHE - ✱✱✱ T-17A 24 RVIA - ✱✱✱ T-19A 16
RPIC - ✱✱✱ T-16A 6 RSJC - ✱✱✱ T-19A 22 RVIB - ✱✱✱ T-19A 17
RPIC - 8✱✱ T-16A 14 RSJC - 8✱✱ T-19A 23 RVID - ✱✱✱ T-24A 19
RPID - ✱✱✱ T-16A 12 RSJE - ✱✱✱ T-19A 24 RVID - 8✱✱ T-24A 20
RPIS - 8✱✱ T-16A 15 RVBA - ✱✱✱ T-163A 16 SCCA - ✱✱✱ T-11A 26
RPKC - ✱✱✱ T-18A 6 RVBB - ✱✱✱ T-163A 17 SCEA - ✱✱✱ T-2A 26
RPKC - 8✱✱ T-18A 14 RVCA - ✱✱✱ T-11A 16 SCGA - ✱✱✱ T-17A 26
RPKD - ✱✱✱ T-18A 12 RVCB - ✱✱✱ T-11A 17 SCIA - ✱✱✱ T-19A 26
RQEB - ✱✱✱ T-10A 11 RVCD - ✱✱✱ T-21A 19 SQDB - ✱✱✱ T-11A 27
RQGB - ✱✱✱ T-3A 11 RVCD - 8✱✱ T-21A 20 SQFB - ✱✱✱ T-2A 27
RQIB - ✱✱✱ T-16A 11 RVEA - ✱✱✱ T-2A 16 SQHB - ✱✱✱ T-17A 27
RQKB - ✱✱✱ T-18A 11 RVEB - ✱✱✱ T-2A 17 SQJB - ✱✱✱ T-19A 27
RSBC - ✱✱✱ T-163A 22 RVED - ✱✱✱ T-22A 19 SXCA - ✱✱✱ T-11A 25
RSDC - ✱✱✱ T-11A 22 RVED - 8✱✱ T-22A 20 SXEA - ✱✱✱ T-2A 25
RSDC - 8✱✱ T-11A 23 RVES - ✱✱✱ T-2A 18
RSFC - ✱✱✱ T-2A 22 RVGS - ✱✱✱ T-17A 18

NOTES

NOTES
174 US Shortcut Catalog 1/04 #999-901-243

NOTES

Warranty
WARRANTY INFORMATION,
PERFORMANCE ASSURANCE,
AND APPLICATION LIMITATIONS
Caution
Sun Hydraulics manufactures a variety of cartridge valves should first check with the manufacturer's service literature,
that will fit into the same Sun cavity. Each cartridge is marked their local Sun distributor, or the Sun factory before making any
with a seven-digit part identification code and a four-digit date part substitutions.
code, stamped on the hex surfaces. Designers and users of Sun
NOTE: To avoid serious injury, the manufacturer's service
components are advised that physical interchangeability of
literature must be consulted before working on any
cartridges does not necessarily mean functional
hydraulic system.
interchangeability. When replacing any Sun cartridges, users
Limited Warranty
Sun Hydraulics warrants its products free from defects in tampering, or abuse, or which have been repaired or altered
material, workmanship, and design for a period of three years outside of the Sun Hydraulics factory. Sun’s liability under this
after their installation, provided the installation date is less than warranty shall extend only to repair or replacement, f.o.b. Sun’s
one year after manufacture. “O-rings” and seals are factory, of any defective part or product determined by
specifically exempted from this warranty. In no instance is inspection as not conforming to this warranty. Sun makes no
there any warranty of fitness for a particular use and Sun other warranties, expressed or implied, and is not responsible
Hydraulics cannot and does not accept responsibility of any for any consequential damages resulting from use by any buyer
type for any of its products that have been subjected to improper or user, Sun Hydraulics’ liability being limited to the value of
installation, improper application, negligence, product sold or obligation to replace a defective part.
Performance Assurance
All Sun cartridges valves are individually tested at the in the buyer's application is the responsibility of the buyer.
factory and preset to specific pressure or flow settings where This is typically accomplished by the manufacture of a
indicated in this product listing. However, as the actual prototype followed by a test or qualification program on the part
performance of buyers' equipment cannot be reproduced in of the buyer.
Sun's testing laboratory, assurance of suitability of Sun products
Application Limitations
Sun product designs and manufacturing facilities have • Ordnance equipment.

been specifically developed to provide products for • Life support equipment.
commercial, industrial and mobile hydraulic applications and • Any end product that comes under the U.S. Nuclear
Sun products are only warranted for these types of uses. Sun's Regulatory Commission rules and regulations, including,
distributors are not authorized to approve the use of Sun but not limited to, products used in nuclear power plant
operations.
products in any of the following applications:
Specific written approval for any application of Sun products in
• Any product that comes under the U.S. Federal Highway
Safety Act, including, but not limited to, steering or braking any of the above named applications should be obtained from Sun
systems for passenger-carrying vehicles or on-highway trucks. Hydraulics. Consultation with Sun distributors or factory engineers
• Aircraft or space vehicles. is advisable in any situations where applicability is questionable.

Catalogo Valvulas Hdcas Sun PDF

Uploaded by

Copyright:

Available Formats

Catalogo Valvulas Hdcas Sun PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Catalogo Valvulas Hdcas Sun PDF

Uploaded by

Copyright:

Available Formats

Over 40 New Products in this Catalogue

US Shortcut Catalogue #999-901-243 1

2 US Shortcut Catalogue #999-901-243

Relief Cartridge Valves . . . . . . . . . . . . . . . . . . . . . . . . 5 Solenoid Operated Cartridge Valves . . . . . . . . . . . 113

Model Codes printed in Red are Preferred Versions of products

SUN RECOMMENDED QUANTITY DISCOUNTS FOR STANDARD VALVES

Quantity: 1-2 3-9 10-29 30-99 100-299 300-999

US Shortcut Catalogue #999-901-243 3

Copyright © 2004 Sun Hydraulics Corporation

Printed in the United States of America

4 US Shortcut Catalogue #999-901-243

2 1 Direct Acting, Pilot Stage 8

Pilot Operated, Balanced Piston, Air Controlled 12

Balanced Poppet, Modulating Element with

Modulating Element with Relief Function 17

4 3 Ventable, Pilot Operated, Balanced Piston with

with External Drain and Integral Pilot Control 20

US Shortcut Catalogue #999-901-243 5

4000 4000 4000 4000 4000

3000 3000 3000 3000

Adjustment Range Options:

3000 4000 4000 4000

4000 3000 3000 3000

3000 3000 3000 3000 3000

Adjustment Range Options:

0 25 50 75 100 0 50 100 150 200

OPTION ORDERING INFORMATION

W 100 - 4500 psi

Adjustment Range Options:

0 10 20 30 40 50 0 200 400 600 800 1000

■ Maximum operating pressure = 5000 psi

OPTION ORDERING INFORMATION

Adjustment Range Options:

200 200 200

0 5 10 15 20 25 0 10 20 30 40 50 0 20 40 60 80 100 0 40 80 120 160 200

■ Maximum operating pressure = 5000 psi

OPTION ORDERING INFORMATION

Adjustment Range Options:

1500 1500 1500

0 25 50 75 100 0 50 100 150 200 0 100 200 300 400

■ Maximum operating pressure = 2000 psi

OPTION ORDERING INFORMATION

I 100 GPM $167.20 A 1/4" NPTF +$ 0.00 V Viton

Available for RPID, RPKD only

RPCC RPEC RPGC 3000

1000 Typical Pressure

5000 5000 5000 5000 5000

3000 3000 3000 3000 3000

Adjustment Range Options:

3000 3000 3000 3000

4000 1000 1000 1000 1000

3000 3000 3000 3000 3000

0 5 10 15 20 25 0 10 20 30 40 50 0 20 40 60 80 100 0 40 80 120 160 200 0 80 160 240 320 400

W 150 - 4500 psi +$ 0.00

Adjustment Range Options:

0 25 50 75 100 0 125 150 175 200

■ Maximum operating pressure = 5000 psi

OPTION ORDERING INFORMATION

Performance Curves Typical Pressure Rise