Spring 2006 Process Dynamics, Operations, and Control 10.

450
Lesson 1: Processes and Systems
1.0 context and direction
Process control is an application area of chemical engineering - an
identifiable specialty for the ChE. It combines chemical process
knowledge (how physics, chemistry, and biology work in operating
equipment) and an understanding of dynamic systems, a topic important to
many fields of engineering. Thus study of process control allows
chemical engineers to span their own field, as well as form a useful
acquaintance with allied fields. Practitioners of process control find their
skills useful in design, operation, and troubleshooting - major categories of
chemical engineering practice.

Process control, like any coherent topic, is an integrated body of

knowledge - it hangs together on a multidimensional framework, and
practitioners draw from many parts of the framework in doing their work.
Yet in learning, we must receive information in sequence - following a
path through multidimensional space. It is like entering a large building
with unlighted rooms, holding a dim flashlight and clutching a vague map
that omits some of the stairways and passages. How best to learn one’s
way around?

In these lessons we will attempt to move through a significant portion of

the structure - say, half a textbook - in about two weeks. Then we will
repeat the journey several times, each time inspecting the rooms more
thoroughly. By this means we hope to gain, from the start, a sense of
doing an entire process control job, as well as approach each new topic in
the context of a familiar path.

1.1 the job we will do, over and over

We encounter a process, learn how it behaves, specify how we wish to
control it, choose appropriate equipment, and then explore the behavior
under control to see if we have improved things.

1.2 introducing a simple process

A large tank must be filled with liquid from a supply line. One operator
stands at ground level to operate the feed valve. Another stands on the
tank, gauging its level with a dipstick. When the tank is near full, the stick
operator will instruct the other to start closing the valve. Overfilling can
cause spills, but underfilling will cause later process problems.

revised 2006 Jan 30 1

Spring 2006 Process Dynamics, Operations, and Control 10.450
Lesson 1: Processes and Systems

To learn how the process works, we write an overall material balance on

the tank.

d
ρV = ρFi (1.2-1)
dt

The tank volume V can be expressed in terms of the liquid level h. The
inlet volumetric flow rate Fi may vary with time due to supply pressure
fluctuations and valve manipulations by the operator. The liquid density
depends on the temperature, but will usually not vary significantly with
time during the course of filling. Thus (1.2-1) becomes

dh
A = Fi ( t ) (1.2-2)
dt

We integrate (1.2-2) to find the liquid level as a function of time.

1 t
A ∫0
h = h ( 0) + Fi ( t )dt (1.2-3)

1.3 planning a control scheme

Clearly the liquid level h is important, and we will call it the controlled
variable. Our control objective is to bring h quickly to its target value hr
and not exceed it. (To be realistic, we would specify allowable limits ± δh
on hr.) We will call the volumetric flow Fi the manipulated variable,
because we adjust it to achieve our objective for the controlled variable.

The existing control scheme is to measure the controlled variable via

dipstick, decide when the controlled variable is near target, and instruct

revised 2006 Jan 30 2

Spring 2006 Process Dynamics, Operations, and Control 10.450
Lesson 1: Processes and Systems
the valve operator to change the manipulated variable. The scheme suffers
from
• delay in measurement. Overfilling can occur if the stick operator
cannot complete the measurement in time.
• performance variations. Both stick and valve operators may vary in
attentiveness and speed of execution.
• resources required. There are better uses for operating personnel.
• unsafe conditions. There is too much potential for chemical exposure.

A new scheme is proposed: put a timer on the valve. Calculate the time
required for filling from (1.2-3). Close the valve when time has expired.

The timing scheme would no longer require an operator to be on the tank

top, and with a motor-driven valve actuator the entire operation could be
directed from a control room. These are indeed improvements. However,
the timing scheme abandons a crucial virtue of the existing scheme: by
measuring the controlled variable, the operators can react to unexpected
disturbances, such as changes in the filling rate. Using knowledge of the
controlled variable to motivate changes to the manipulated variable is a
fundamental control structure, known as feedback control. The proposed
timing scheme has no feedback mechanism, and thus cannot accommodate
changes to h(0) and Fi(t) in (1.2-3).

An alternative is to build on the feedback already inherent in the two-

operator scheme, but to improve its operation. We propose an automatic
controller that behaves according to the following controller algorithm:

h < h near Fi = Fmax

hr − h (1.3-1)
h > h near Fi = Fmax
h r − h near

Algorithm (1.3-1) is an idealization of what the operators are already

doing: filling occurs at maximum flow until the level reaches a value hnear.
Beyond this point, the flow decreases linearly, reaching zero when h
reaches the target hr. The setting of hnear may be adjusted to tune the
control performance.

1.4 choosing equipment

We need a sensor to replace the dipstick, a valve actuator to replace the
valve operator, and a controller mechanism to replace the stick operator.
We imagine a buoyant object floating on the liquid surface. The float is
linked to a lever that drives the valve stem. When the liquid level is low,
the float rests above it on a structure so that the valve is fully open.

revised 2006 Jan 30 3

Spring 2006 Process Dynamics, Operations, and Control 10.450
Lesson 1: Processes and Systems

Content removed due to copyright restrictions.

(To see a cut-away diagram of a toilet, go to
http://www.toiletology.com/lg-views.shtml#cutaway2x)

1.5 process behavior under automatic control

Typically these things work quite well. We predict its performance by
combining our process model (1.2-2) with the controller algorithm (1.3-1),
which eliminates the manipulated variable between the equations. We
take the simple case in which Fmax does not vary during filling due to
pressure fluctuations, etc. For h less than hnear,

dh
A = Fmax h (0) = known
dt (1.5-1)
F
h = h (0) + max t
A

Equation (1.5-1) can be used to calculate tnear, the time at which h reaches
hnear. For h greater than hnear,

dh hr − h
A = Fmax h(t near ) = h near
dt h r − h near
(1.5-2)
⎡ − h r (t − t near ) ⎤
h = h r − ( h r − h near ) exp ⎢ ⎥
⎢⎣ t fill ( h r − h near ) ⎥⎦

revised 2006 Jan 30 4

Spring 2006 Process Dynamics, Operations, and Control 10.450
Lesson 1: Processes and Systems

where the parameter tfill is the time required for the level to reach hr at
flow Fmax, starting from an empty tank.

Ah r
t fill = (1.5-3)
Fmax

The plot shows the filling profile from h(0) = 0.10hr with several values of
hnear/hr. Certainly the filling goes faster if the flow can go instantaneously
from Fmax to zero at hr; however this will not be practical, so that hnear will
be less than hr.

1.2
hnear/hr = 0.95
1 0.75
0.50
0.8
h/hr

0.6

0.4

0.2

0
0 0.2 0.4 0.6 0.8 1 1.2 1.4
t/tfill

1.6 defining ‘system’

In Section 1.2, we introduced a process - a tank with feed piping - whose
inventory varied in time. We thought of the process as a collection of
equipment and other material, marked off by a boundary in space,
communicating with its environment by energy and material streams.

'Process' is a good notion, important to chemical engineers. Another

useful notion is that of 'system'. A system is some collection of equipment
and operations, usually with a boundary, communicating with its
environment by a set of input and output signals. By these definitions, a
process is a type of system, but system is more abstract and general. For
example, the system boundary is often tenuous: suppose that our system
comprises the equipment in the plant and the controller in the central
control room, with radio communication between the two. A physical
boundary would be in two pieces, at least; perhaps we should regard this

revised 2006 Jan 30 5

Spring 2006 Process Dynamics, Operations, and Control 10.450
Lesson 1: Processes and Systems
system boundary as partly physical (around the chemical process) and
partly conceptual (around the controller).

Furthermore, the inputs and outputs of a system need not be material and
energy streams, as they are for a process. System inputs are "things that
cause" or “stimuli”; outputs are "things that are affected" or “responses”.

inputs system outputs

(causes) (responses)

To approach the problem of controlling our filling process in Section 1.3,

we thought of it in system terms: the primary output was the liquid level h
-- not a stream, certainly, but an important response variable of the system
-- and inlet stream Fi was an input. And peculiar as it first seems, if the
tank had an outlet flow Fo, it would also be an input signal, because it
influences the liquid level, just as does Fi.

The point of all this is to look at a single schematic and know how to view
it as a process, and as a system. View it as a process (Fo as an outlet
stream) to write the material balance and make fluid mechanics
calculations. View it as a system (Fo as an input) to analyze the dynamic
behavior implied by that material balance and make control calculations.

System dynamics is an engineering science useful to mechanical,

electrical, and chemical engineers, as well as others. This is because
transient behavior, for all the variety of systems in nature and technology,
can be described by a very few elements. To do our job well, we must
understand more about system dynamics -- how systems behave in time.
That is, we must be able to describe how important output variables react
to arbitrary disturbances.

1.7 systems within systems

We call something a system and identify its inputs and outputs as a first
step toward understanding, predicting, and influencing its behavior. In
some cases it may help to determine some of the structure within the
system boundaries; that is, if we identify some component systems. Each
of these, of course, would have inputs and outputs, too.

system
inputs outputs
1
2

revised 2006 Jan 30 6

Spring 2006 Process Dynamics, Operations, and Control 10.450
Lesson 1: Processes and Systems

Considering the relationship of these component systems, we recognize

the existence of intermediate variables within a system. Neither inputs
nor outputs of the main system, they connect the component systems.
Intermediate variables may be useful in understanding and influencing
overall system behavior.

1.8 the system of single-loop feedback control

When we add a controller to a process, we create a single time-varying
system; however, it is useful to keep process and controller conceptually
distinct as component systems. This is because a repertoire of relatively
few control schemes (relationships between process and controller)
suffices for myriad process applications. Using the terms we defined in
Section 1.3, we represent a control scheme called single-loop feedback
control in this fashion:

system

other inputs other

outputs
process

controlled
manipulated
variable
variable
final control sensor
element

controller

set point

Figure 1.8-1 The single-loop feedback control system and its

subsystems

We will see this structure repeatedly. Inside the block called "process" is
the physical process, whatever it might be, and the block is the boundary
we would draw if we were doing an overall material or energy balance.
HOWEVER, we remember that the inputs and outputs are NOT
necessarily the same as the material and energy streams that cross the
process boundary. From among the outputs, we may select a controlled
variable (often a pressure, temperature, flow rate, liquid level, or
composition) and provide a suitable sensor to measure it. From the inputs,
we choose a manipulated variable (often a flow rate) and install an
appropriate final control element (often a valve). The measurement is fed
to the controller, which decides how to adjust the manipulated variable to
keep the controlled variable at the desired condition: the set point. The

revised 2006 Jan 30 7

Spring 2006 Process Dynamics, Operations, and Control 10.450
Lesson 1: Processes and Systems
other inputs are potential disturbances that affect the controlled variable,
and so require action by the controller.

1.9 conclusion
Think of a chemical process as a dynamic system that responds in
particular ways to its inputs. We attach other dynamic systems (sensor,
controller, etc.) to that process in a single-loop feedback structure and
arrive at a new dynamic system that responds in different ways to the
inputs. If we do our job well, it responds in better ways, so to justify all
the trouble.

revised 2006 Jan 30 8