Scribd
Upload
128 views2 pages

Eec130b 2019 HW8

This document contains 8 homework problems assigned on February 27, 2019 related to waveguide modes. Problem 1 asks about cutoff frequencies and wavelengths of TE modes in parallel plate waveguides with different permittivities. Problem 2 asks about the number of modes in a dielectric waveguide. Problem 3 asks about the cutoff frequency of a TE2 mode in a dielectric slab waveguide.

Uploaded by

NGUYEN NGUYEN
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
128 views2 pages

Eec130b 2019 HW8

This document contains 8 homework problems assigned on February 27, 2019 related to waveguide modes. Problem 1 asks about cutoff frequencies and wavelengths of TE modes in parallel plate waveguides with different permittivities. Problem 2 asks about the number of modes in a dielectric waveguide. Problem 3 asks about the cutoff frequency of a TE2 mode in a dielectric slab waveguide.

Uploaded by

NGUYEN NGUYEN
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Assigned: 02/27/2019

Winter 2019
EEC 130B Homework #8
Due: 03/06/19 by 11:59pm (EEC130B Homework Box in Kemper 2131)

Problem 1: Parallel-plate waveguide modes.

Consider a parallel plate waveguide filled with a nonmagnetic medium with a


permittivity ε=9𝜀0 . The spacing between the plates is 10 cm.
What are the cutoff frequency and cutoff wavelength of the m=2 TE mode?
What are the cutoff frequency and cut off wavelength if the permittivity of the
filling material is increased to ε=16𝜀0 ? What is the propagation constant of the
TE2 mode at 1.5 GHz in each case?

Problem 2: dielectric waveguide modes.

How many modes exist in a dielectric waveguide that has the following
parameters? Index of refraction of the core n1 = 1.6, index of refraction of the
cladding n2 = 1.5, wavelength λ = 1.0μm, waveguide core thickness 2d = 4 μm.

Problem 3: TE2 mode in a dielectric slab waveguide.

Find the cutoff frequency for the TE2 mode in a dielectric slab waveguide with
ε=7𝜀0 and thickness 2 cm, which is embedded in another dielectric with ε=3𝜀0 .
Assume nonmagnetic case.

Problem 4: Millimeter-wave dielectric slab waveguide.

Consider a dielectric slab waveguide with 𝜀𝑑 =4𝜀0 and 𝜇𝑑 =𝜇0 surrounded by air to
be used to guide millimeter waves. Find the guide thickness d such that only the
TE1 mode can propagate at frequency up to 300GHz.
Assigned: 02/27/2019

Problem 5: Power and loss for the TE parallel-plate mode.

Find average power transfer and conductor loss for a TE mode between parallel
planes to verify the expression for attenuation:
2𝑅𝑠 (𝑤𝑐 ⁄𝑤)2
(𝛼𝑐 )𝑇𝐸 =
𝜂𝑎√1 − (𝑤𝑐 ⁄𝑤)2

Problem 6:
The magnetic field of a particular mode in a parallel-plate air waveguide with a
plate separation of 2.5 cm is given by

where x and y are both in meters.

a. Classify the mode. Is it a propagating or a non-propagating mode?


b. What is the operating frequency?
c. Find the corresponding electric field.
d. Find the lowest-order similar mode (TEm or TMm) that does not propagate in this
waveguide at the same frequency.

Problem 7: Parallel-plate waveguide modes.


Consider a parallel plate waveguide filled with a nonmagnetic medium with a
permittivity ε=9𝜀0 . The spacing between the plates is 10 cm.
What are the cutoff frequency and cutoff wavelength of the m=2 TE mode?
What are the cutoff frequency and cut off wavelength if the permittivity of the
filling material is increased to ε=16𝜀0 ? What is the propagation constant of the
TE2 mode at 1.5 GHz in each case?

Problem 8: TE2 mode in a dielectric slab waveguide

Find the cutoff frequency for the TE2 mode in a dielectric slab waveguide with
ε=7𝜀0 and thickness 2 cm, which is embedded in another dielectric with ε=3𝜀0 .
Assume nonmagnetic case.

You might also like