TECHNICAL REPORT

TR-069
CPE WAN Management Protocol
Issue: 1 Amendment 5
Issue Date: November 2013
CWMP Version: 1.4

© The Broadband Forum. All rights reserved.

CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Notice
The Broadband Forum is a non-profit corporation organized to create guidelines for
broadband network system development and deployment. This Broadband Forum
Technical Report has been approved by members of the Forum. This Broadband Forum
Technical Report is not binding on the Broadband Forum, any of its members, or any
developer or service provider. This Broadband Forum Technical Report is subject to
change, but only with approval of members of the Forum. This Technical Report is
copyrighted by the Broadband Forum, and all rights are reserved. Portions of this
Technical Report may be copyrighted by Broadband Forum members.

This Broadband Forum Technical Report is provided AS IS, WITH ALL FAULTS. ANY
PERSON HOLDING A COPYRIGHT IN THIS BROADBAND FORUM TECHNICAL
REPORT, OR ANY PORTION THEREOF, DISCLAIMS TO THE FULLEST EXTENT
PERMITTED BY LAW ANY REPRESENTATION OR WARRANTY, EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY:

(A) OF ACCURACY, COMPLETENESS, MERCHANTABILITY, FITNESS FOR A

PARTICULAR PURPOSE, NON-INFRINGEMENT, OR TITLE;
(B) THAT THE CONTENTS OF THIS BROADBAND FORUM TECHNICAL
REPORT ARE SUITABLE FOR ANY PURPOSE, EVEN IF THAT PURPOSE IS
KNOWN TO THE COPYRIGHT HOLDER;
(C) THAT THE IMPLEMENTATION OF THE CONTENTS OF THE TECHNICAL
REPORT WILL NOT INFRINGE ANY THIRD PARTY PATENTS,
COPYRIGHTS, TRADEMARKS OR OTHER RIGHTS.

By using this Broadband Forum Technical Report, users acknowledge that

implementation may require licenses to patents. The Broadband Forum encourages but
does not require its members to identify such patents. For a list of declarations made by
Broadband Forum member companies, please see http://www.broadband-forum.org. No
assurance is given that licenses to patents necessary to implement this Technical Report
will be available for license at all or on reasonable and non-discriminatory terms.

ANY PERSON HOLDING A COPYRIGHT IN THIS BROADBAND FORUM

TECHNICAL REPORT, OR ANY PORTION THEREOF, DISCLAIMS TO THE
FULLEST EXTENT PERMITTED BY LAW (A) ANY LIABILITY (INCLUDING
DIRECT, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES UNDER ANY
LEGAL THEORY) ARISING FROM OR RELATED TO THE USE OF OR
RELIANCE UPON THIS TECHNICAL REPORT; AND (B) ANY OBLIGATION TO
UPDATE OR CORRECT THIS TECHNICAL REPORT.

Broadband Forum Technical Report may be copied, downloaded, stored on a server or

otherwise re-distributed in their entirety only, and may not be modified without the
advance written permission of the Broadband Forum.

The text of this notice must be included in all copies of this Broadband Forum Technical
Report.

November 2013 © The Broadband Forum. All rights reserved. Page 2 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Issue History

Issue Approval Publication Issue Editor Changes

Number Date Date
Issue 1 May 2004 Jeff Bernstein, 2Wire Issue 1
Tim Spets, Westell
Issue 1 November Jeff Bernstein, 2Wire Clarification of original document
Amendment 1 2006 John Blackford, 2Wire
Mike Digdon, SupportSoft
Heather Kirksey, Motive
William Lupton, 2Wire
Anton Okmianski, Cisco
Issue 1 November William Lupton, 2Wire CWMP Version 1.1: Multicast
Amendment 2 2007 Davide Moreo, Telecom Download support, 10
Italia AUTONOMOUS TRANSFER
COMPLETE event,
AutonomousTransferComplete
method, additional Download fault
codes, interoperability clarifications,
minor editorial changes.
Issue 1 November John Blackford, Pace CWMP Version 1.2: Small updates
Amendment 3 2010 Heather Kirksey, Alcatel- for IPv6 related to DHCP, Additions
Lucent for Software Module Management
William Lupton, Pace support (including new RPCs, Inform
Event Codes, fault codes, and an
Annex on UUIDs),
ScheduleDownload RPC, and
CancelTransfer RPC.
Issue 1 July 2011 Sarah Banks, Cisco CWMP Version 1.3: Added Proxy
Amendment 4 Andrea Colmegna, management support and added
FASTWEB Tim Spets, Annex J and Appendix I. Table 4
Motorola Mobility Session timeout updated. Removed
xsd Section A.6.
Added Alias-Based Addressing
additions, Section 3.6.1, Appendix II,
and RPC Definition updates.
Issue 1 11 8 January John Blackford, Pace CWMP Version 1.4: Added XMPP
Amendment 5 November 2014 Mike Digdon, Aptean Connection Request support (Annex
2013 K and Appendix III), CPE standby-
related behaviors (Annex L), UDP
Lightweight Notification support
(Annex M), and several other small
clarifications/enhancements.

Comments or questions about this Broadband Forum Technical Report should be directed
to [email protected].

November 2013 © The Broadband Forum. All rights reserved. Page 3 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Editors John Blackford Pace

Mike Digdon Aptean

BroadbandHome™ John Blackford Pace

Working Group Chairs Jason Walls QACafe

November 2013 © The Broadband Forum. All rights reserved. Page 4 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Table of Contents
1 Introduction ................................................................................................................ 16
1.1 Functional Components ................................................................................. 16
1.1.1 Auto-Configuration and Dynamic Service Provisioning ................... 16
1.1.2 Software/Firmware Image Management ............................................ 17
1.1.3 Software Module Management .......................................................... 17
1.1.4 Status and Performance Monitoring .................................................. 17
1.1.5 Diagnostics ......................................................................................... 17
1.2 Positioning in the End-to-End Architecture ................................................... 17
1.3 Security Goals ................................................................................................ 18
1.4 Architectural Goals ........................................................................................ 18
1.5 Assumptions ................................................................................................... 19
1.6 Terminology ................................................................................................... 20
1.7 Abbreviations ................................................................................................. 22
1.8 Document Conventions .................................................................................. 24
2 Architecture ................................................................................................................ 26
2.1 Protocol Components ..................................................................................... 26
2.2 Security Mechanisms ..................................................................................... 27
2.3 Architectural Components ............................................................................. 27
2.3.1 Parameters .......................................................................................... 27
2.3.2 File Transfers ..................................................................................... 28
2.3.3 CPE Initiated Sessions ....................................................................... 28
2.3.4 Asynchronous ACS Initiated Sessions ............................................... 29
3 Procedures and Requirements .................................................................................... 30
3.1 ACS Discovery .............................................................................................. 30
3.2 Connection Establishment ............................................................................. 33
3.2.1 CPE Connection Initiation ................................................................. 33
3.2.2 ACS Connection Initiation ................................................................. 36
3.3 Use of TLS and TCP ...................................................................................... 38
3.4 Use of HTTP .................................................................................................. 40
3.4.1 Encoding SOAP over HTTP .............................................................. 40
3.4.2 Sessions .............................................................................................. 41
3.4.3 File Transfers ..................................................................................... 43
3.4.4 Authentication .................................................................................... 43
3.4.5 Digest Authentication ........................................................................ 44
3.4.6 Additional HTTP Requirements ........................................................ 45
3.4.7 HTTP Compression ........................................................................... 45
3.5 Use of SOAP .................................................................................................. 46
3.6 RPC Support Requirements ........................................................................... 52
3.6.1 Alias-Based Addressing Mechanism Requirements .......................... 53
3.7 Session Procedures ......................................................................................... 56
3.7.1 CPE Operation ................................................................................... 56
3.7.2 ACS Operation ................................................................................... 66
3.7.3 Transaction Examples ........................................................................ 69
3.7.4 CWMP Version Negotiation .............................................................. 70

November 2013 © The Broadband Forum. All rights reserved. Page 5 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Normative References ....................................................................................................... 71

Annex A. RPC Methods ................................................................................................ 74
A.1 Introduction ................................................................................................................ 74
A.2 RPC Method Usage .................................................................................................... 74
A.2.1 Data Types ..................................................................................................... 74
A.2.2 Instance Identifiers ......................................................................................... 75
A.2.2.1 Instance Number Identifier ................................................................ 75
A.2.2.2 Instance Alias Identifier ..................................................................... 76
A.2.3 Other Requirements ....................................................................................... 76
A.3 Baseline RPC Messages ............................................................................................. 77
A.3.1 Generic Methods ............................................................................................ 77
A.3.1.1 GetRPCMethods ................................................................................ 77
A.3.2 CPE Methods ................................................................................................. 78
A.3.2.1 SetParameterValues ........................................................................... 78
A.3.2.2 GetParameterValues........................................................................... 81
A.3.2.3 GetParameterNames........................................................................... 82
A.3.2.4 SetParameterAttributes ...................................................................... 84
A.3.2.5 GetParameterAttributes...................................................................... 88
A.3.2.6 AddObject .......................................................................................... 90
A.3.2.7 DeleteObject ...................................................................................... 93
A.3.2.8 Download ........................................................................................... 95
A.3.2.9 Reboot .............................................................................................. 100
A.3.3 ACS Methods ............................................................................................... 101
A.3.3.1 Inform .............................................................................................. 101
A.3.3.2 TransferComplete ............................................................................ 104
A.3.3.3 AutonomousTransferComplete ........................................................ 105
A.4 Optional RPC Messages ........................................................................................... 107
A.4.1 CPE Methods ............................................................................................... 107
A.4.1.1 GetQueuedTransfers ........................................................................ 107
A.4.1.2 ScheduleInform ................................................................................ 107
A.4.1.3 SetVouchers ..................................................................................... 108
A.4.1.4 GetOptions ....................................................................................... 108
A.4.1.5 Upload .............................................................................................. 110
A.4.1.6 FactoryReset .................................................................................... 112
A.4.1.7 GetAllQueuedTransfers ................................................................... 112
A.4.1.8 ScheduleDownload .......................................................................... 114
A.4.1.9 CancelTransfer ................................................................................. 118
A.4.1.10 ChangeDUState................................................................................ 118
A.4.2 ACS Methods ............................................................................................... 122
A.4.2.1 Kicked .............................................................................................. 122
A.4.2.2 RequestDownload ............................................................................ 122
A.4.2.3 DUStateChangeComplete ................................................................ 123
A.4.2.4 AutonomousDUStateChangeComplete ........................................... 126
A.5 Fault Handling .......................................................................................................... 129
A.5.1 CPE Fault Codes .......................................................................................... 129
A.5.2 ACS Fault Codes.......................................................................................... 131

November 2013 © The Broadband Forum. All rights reserved. Page 6 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

A.6 RPC Method XML Schema ..................................................................................... 131

Annex B. Removed ..................................................................................................... 132
Annex C. Signed Vouchers ......................................................................................... 133
C.1 Overview .................................................................................................................. 133
C.2 Control of Options Using Vouchers ......................................................................... 133
C.3 Voucher Definition ................................................................................................... 134
Annex D. Web Identity Management .......................................................................... 138
D.1 Overview .................................................................................................................. 138
D.2 Use of the Kicked RPC Method ............................................................................... 138
D.3 Web Identity Management Procedures .................................................................... 139
D.4 LAN Side Interface .................................................................................................. 140
Annex E. Signed Package Format............................................................................... 142
E.1 Introduction .............................................................................................................. 142
E.2 Signed Package Format Structure ............................................................................ 142
E.2.1 Encoding Conventions ................................................................................. 143
E.3 Header Format .......................................................................................................... 143
E.4 Command List Format ............................................................................................. 143
E.4.1 Command Types .......................................................................................... 144
E.4.2 End Command ............................................................................................. 145
E.4.3 Extract and Add Commands ........................................................................ 145
E.4.4 Remove Commands ..................................................................................... 146
E.4.5 Move Commands ......................................................................................... 146
E.4.6 Version and Description Commands ........................................................... 147
E.4.7 Timeout Commands ..................................................................................... 147
E.4.8 Reboot Command ........................................................................................ 149
E.4.9 Format File System ...................................................................................... 149
E.4.10 Minimum and Maximum Version Commands ............................................ 149
E.4.11 Role Command ............................................................................................ 151
E.4.12 Minimum Storage Commands ..................................................................... 151
E.4.13 Required Attributes Command .................................................................... 151
E.5 Signatures ................................................................................................................. 152
Annex F. Device-Gateway Association ...................................................................... 154
F.1 Introduction .............................................................................................................. 154
F.1.1 Terminology ................................................................................................. 154
F.2 Procedures ................................................................................................................ 155
F.2.1 Gateway Requirements ................................................................................ 155
F.2.2 Device Requirements ................................................................................... 156
F.2.3 ACS Requirements....................................................................................... 157
F.2.4 Device-Gateway Association Flows ............................................................ 158
F.2.5 DHCP Vendor Options ................................................................................ 159
F.3 Security Considerations............................................................................................ 160
Annex G. Connection Request via NAT Gateway ...................................................... 162
G.1 Introduction .............................................................................................................. 162

November 2013 © The Broadband Forum. All rights reserved. Page 7 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

G.2 Procedures ................................................................................................................ 162

G.2.1 CPE Requirements ....................................................................................... 163
G.2.1.1 Binding Discovery ........................................................................... 164
G.2.1.2 Maintaining the Binding .................................................................. 165
G.2.1.3 Communication of the Binding Information to the ACS ................. 166
G.2.1.4 UDP Connection Requests ............................................................... 168
G.2.2 ACS Requirements....................................................................................... 169
G.2.2.1 STUN Server Requirements ............................................................ 169
G.2.2.2 Determination of the Binding Information ...................................... 170
G.2.2.3 UDP Connection Requests ............................................................... 171
G.2.3 Message Flows ............................................................................................. 173
G.3 Security Considerations............................................................................................ 176
Annex H. Software Module Management UUID Usage ............................................. 177
H.1 Overview .................................................................................................................. 177
H.2 UUID Generation Requirements .............................................................................. 178
H.3 CPE Requirements ................................................................................................... 178
Annex I............................................................................................................................ 179
Annex J. CWMP Proxy Management .......................................................................... 180
J.1 Introduction .............................................................................................................. 180
J.2 The Virtual CWMP Device Mechanism .................................................................. 181
J.2.1 Data Model Requirements ........................................................................... 181
J.2.2 Proxied Device Identification and Modeling ............................................... 181
J.2.3 Proxied Device Availability ......................................................................... 182
J.3 The Embedded Object Mechanism .......................................................................... 183
J.3.1 Proxied Device Data Modeling and Provisioning ....................................... 183
J.3.2 Proxied Device Availability ......................................................................... 183
Annex K. XMPP Connection Request ........................................................................ 185
K.1 Introduction .............................................................................................................. 185
K.2 Procedures ................................................................................................................ 185
K.2.1 CPE Requirements ....................................................................................... 187
K.2.1.1 XMPP Connection Encryption ........................................................ 189
K.2.1.2 XMPP Channel Authentication........................................................ 189
K.2.1.3 XMPP Connection Request ............................................................. 189
K.2.2 ACS Requirements....................................................................................... 191
K.2.2.1 XMPP Connection Encryption ........................................................ 191
K.2.2.2 XMPP Connection Request ............................................................. 191
K.2.3 Message Flows ............................................................................................. 192
K.2.3.1 Connection Request ......................................................................... 192
K.2.3.2 Connection Request Successful Response ....................................... 193
K.2.3.3 Connection Request Error Response ............................................... 193
K.3 XMPP Server Deployment Requirements................................................................ 194
K.4 Security Considerations............................................................................................ 194
Annex L. CPE standby-related behaviors ................................................................... 195
L.1 Introduction .............................................................................................................. 195

November 2013 © The Broadband Forum. All rights reserved. Page 8 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

L.2 Procedures ................................................................................................................ 196

L.2.1 Use of WAKEUP Event ............................................................................... 196
L.2.2 Conditions requiring a WAKEUP Event ..................................................... 196
L.2.3 When to deliver a WAKEUP Event ............................................................. 196
L.2.4 Management of standby modes by the ACS ................................................ 196
Annex M. UDP Lightweight Notification .................................................................... 198
M.1 Introduction .............................................................................................................. 198
M.2 Procedures ................................................................................................................ 198
M.2.1 CPE requirements ........................................................................................ 198
M.2.2 ACS requirements ........................................................................................ 199
M.2.3 UDPLightweightNotification message ........................................................ 199
M.2.4 Message arguments ...................................................................................... 200
M.2.5 UDPLightweightNotification XML Schema ............................................... 201
M.2.6 UDPLightweightNotification example ........................................................ 201
Appendix I. CPE Proxier Implementation Guidelines ................................................ 202
I.1 Introduction .............................................................................................................. 202
I.2 Common Guidelines for the Virtual CWMP Device and Embedded Object
Mechanisms .................................................................................................................... 202
I.2.1 Unsupported CWMP RPC Commands by the Proxy Protocol .................... 202
I.2.2 Support for Proxy Protocol Methods with no Matching RPC ..................... 202
I.2.3 Support for Transactional Integrity .............................................................. 203
I.3 Embedded Object Mechanism ................................................................................. 203
I.3.1 Device Discovery ......................................................................................... 203
I.3.2 CPE Proxier use of Polling .......................................................................... 204
I.3.3 ACS Query of RPC Execution ..................................................................... 204
I.3.4 Support for Proxy Protocol Methods Reboot and Download ...................... 204
I.4 Virtual CWMP Device Mechanism ......................................................................... 205
I.4.1 Device Discovery ......................................................................................... 205
I.4.2 Request for Session Timeout Extension ...................................................... 205
I.4.3 CPE Proxier use of Caching ........................................................................ 206
I.4.4 Virtual CWMP Device Error Scenarios ....................................................... 207
I.5 Proxy Management Support Example...................................................................... 208
Appendix II. Alias-Based Addressing Mechanism – Theory of Operations................ 210
II.1 Introduction .............................................................................................................. 210
II.2 Multi-Instance Objects Definition ............................................................................ 210
II.3 Instance Alias as a Data Model Parameter ............................................................... 211
II.4 Multi-Instance Object Creation ................................................................................ 211
II.5 AddObject RPC Extension ....................................................................................... 212
II.6 Auto-Creation of Object Instances ........................................................................... 212
II.7 Support for Alias-Based Addressing Mechanism .................................................... 213
Appendix III. XMPP Connection – Theory of Operations ......................................... 214
III.1 Introduction .................................................................................................... 214
III.2 XMPP Summary............................................................................................. 214

November 2013 © The Broadband Forum. All rights reserved. Page 9 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

III.3 XMPP Identities ............................................................................................. 214

III.3.1 CPE Considerations ..................................................................................... 214
III.4 Establishing an XMPP Connection ................................................................ 215
III.4.1 Determining the XMPP Server Address and Port ........................................ 215
III.4.2 XML Streams ............................................................................................... 216
III.4.3 XMPP Connection Encryption .................................................................... 216
III.4.4 XMPP Channel Authentication.................................................................... 216
III.4.5 Reconnecting to the XMPP Server .............................................................. 216
III.5 Maintaining an XMPP Connection ................................................................ 217
III.6 Deployment Considerations ........................................................................... 217
Appendix IV. UPnP IGD and HTTP Connection Requests ......................................... 219
IV.1 Introduction .................................................................................................... 219
IV.2 NAT Port Mapping Theory of Operation ....................................................... 219
IV.2.1 Discovery and External IP Address Retrieval.............................................. 219
IV.2.2 Procedures for WANPPPConnection:1 ....................................................... 220
IV.2.3 Procedures for WANIPConnection:2........................................................... 223
IV.2.4 Handling Changes ........................................................................................ 224
IV.3 IPv6 Pinhole Theory of Operation ................................................................. 224
IV.3.1 Discovery ..................................................................................................... 225
IV.3.2 Procedures .................................................................................................... 225
IV.3.3 Handling Changes ........................................................................................ 227

November 2013 © The Broadband Forum. All rights reserved. Page 10 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

List of Tables
Table 1 – Protocol layer summary .................................................................................... 26
Table 2 – Encapsulated Vendor Specific Options ............................................................ 31
Table 3 – Session Retry Wait Intervals ............................................................................. 35
Table 4 – SOAP Header Elements .................................................................................... 50
Table 5 – RPC message requirements .............................................................................. 52
Table 6 – Inferring ACS CWMP Version 1.0-1.3 from CWMP Namespace ................... 57
Table 7 – CPE Message Transmission Constraints .......................................................... 58
Table 8 – Event Types ...................................................................................................... 61
Table 9 – Inferring CPE CWMP Version 1.0-1.3 from CWMP Namespace ................... 66
Table 10 – ACS Message Transmission Constraints ........................................................ 67
Table 11 – CWMP Version Negotiation ........................................................................... 70
Table 12 – Data types ....................................................................................................... 74
Table 13 – GetRPCMethods arguments ........................................................................... 77
Table 14 – GetRPCMethodsResponse arguments ............................................................ 78
Table 15 – SetParameterValues arguments ...................................................................... 78
Table 16 – SetParameterValuesResponse arguments ....................................................... 79
Table 17 – ParameterValueStruct definition..................................................................... 80
Table 18 – GetParameterValues arguments ...................................................................... 82
Table 19 – GetParameterValuesResponse arguments ...................................................... 82
Table 20 – GetParameterNames arguments ...................................................................... 82
Table 21 – GetParameterNamesResponse arguments ...................................................... 83
Table 22 – ParameterInfoStruct definition ....................................................................... 83
Table 23 – SetParameterAttributes arguments ................................................................. 85
Table 24 – SetParameterAttributesResponse arguments .................................................. 85
Table 25 – SetParameterAttributesStruct definition ......................................................... 85
Table 26 – GetParameterAttributes arguments ................................................................. 88
Table 27 – GetParameterAttributesResponse arguments ................................................. 88
Table 28 – ParameterAttributeStruct definition ................................................................ 89
Table 29 – AddObject arguments ..................................................................................... 92
Table 30 – AddObjectResponse arguments ...................................................................... 92
Table 31 – DeleteObject arguments .................................................................................. 94
Table 32 – DeleteObjectResponse arguments .................................................................. 94
Table 33 – Download arguments ...................................................................................... 96
Table 34 – DownloadResponse arguments ..................................................................... 100
Table 35 – Reboot arguments ......................................................................................... 101
Table 36 – RebootResponse arguments .......................................................................... 101
Table 37 – Inform arguments .......................................................................................... 101
Table 38 – InformResponse arguments .......................................................................... 102
Table 39 – DeviceIdStruct definition .............................................................................. 103
Table 40 – EventStruct definition ................................................................................... 103
Table 41 – TransferComplete arguments ........................................................................ 104
Table 42 – TransferCompleteResponse arguments ........................................................ 104
Table 43 – FaultStruct definition .................................................................................... 105
Table 44 – AutonomousTransferComplete arguments ................................................... 105

November 2013 © The Broadband Forum. All rights reserved. Page 11 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Table 45 – AutonomousTransferCompleteResponse arguments .................................... 106

Table 46 – GetQueuedTransfers arguments ................................................................... 107
Table 47 – GetQueuedTransfersResponse arguments .................................................... 107
Table 48 – QueuedTransferStruct definition .................................................................. 107
Table 49 – ScheduleInform arguments ........................................................................... 108
Table 50 – ScheduleInformResponse arguments ............................................................ 108
Table 51 – SetVouchers arguments ................................................................................ 108
Table 52 – SetVouchersResponse arguments ................................................................. 108
Table 53 – GetOptions arguments .................................................................................. 109
Table 54 – GetOptionsResponse arguments ................................................................... 109
Table 55 – OptionStruct definition ................................................................................. 109
Table 56 – Upload arguments ......................................................................................... 110
Table 57 – UploadResponse arguments .......................................................................... 112
Table 58 – FactoryReset arguments ................................................................................ 112
Table 59 – FactoryResetResponse arguments ................................................................ 112
Table 60 – GetAllQueuedTransfers arguments .............................................................. 113
Table 61 – GetAllQueuedTransfersResponse arguments ............................................... 113
Table 62 – AllQueuedTransferStruct definition ............................................................. 113
Table 63 – ScheduleDownload arguments ..................................................................... 115
Table 64 – ScheduleDownloadResponse arguments ...................................................... 116
Table 65 – TimeWindowStruct definition ...................................................................... 117
Table 66 – CancelTransfer arguments ............................................................................ 118
Table 67 – CancelTransferResponse arguments ............................................................. 118
Table 68 – ChangeDUState Arguments .......................................................................... 120
Table 69 – ChangeDUStateResponse Arguments .......................................................... 120
Table 70 – OperationStruct Types .................................................................................. 120
Table 71 – InstallOpStruct Definition............................................................................. 120
Table 72 – UpdateOpStruct Definition ........................................................................... 121
Table 73 – UninstallOpStruct Definition ........................................................................ 121
Table 74 – Kicked arguments ......................................................................................... 122
Table 75 – KickedResponse arguments .......................................................................... 122
Table 76 – RequestDownload arguments ....................................................................... 122
Table 77 – RequestDownloadResponse arguments ........................................................ 123
Table 78 – ArgStruct definition ...................................................................................... 123
Table 79 – DUStateChangeComplete Arguments .......................................................... 124
Table 80 – OpResultStruct Definition ............................................................................ 124
Table 81 – FaultStruct Definition ................................................................................... 125
Table 82 – DUStateChangeCompleteResponse Arguments ........................................... 126
Table 83 – AutonomousDUStateChangeComplete Arguments ..................................... 127
Table 84 – AutonOpResultStruct Definition .................................................................. 127
Table 85 – FaultStruct Definition ................................................................................... 128
Table 86 – AutonomousDUStateChangeCompleteResponse Arguments ...................... 129
Table 87 – Fault codes .................................................................................................... 129
Table 88 – Fault codes .................................................................................................... 131
Table 89 – CWMP XML Schema Versions ................................................................... 131
Table 90 – Option specification definition ..................................................................... 134

November 2013 © The Broadband Forum. All rights reserved. Page 12 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Table 91 – DeviceIdStruct definition .............................................................................. 135

Table 92 – Recommended CGI Arguments for the kick URL ....................................... 140
Table 93 – Signed package component summary........................................................... 142
Table 94 – Signed package header format ...................................................................... 143
Table 95 – Command format .......................................................................................... 143
Table 96 – Command Type summary ............................................................................. 144
Table 97 – Value format for the extract and add commands .......................................... 145
Table 98 – Value format for the remove commands ...................................................... 146
Table 99 – Value format for the move commands ......................................................... 147
Table 100 – Value format for the timeout commands .................................................... 148
Table 101 – Timeout command definitions .................................................................... 149
Table 102 – Value format for the minimum and maximum version commands ............ 150
Table 103 – Value format for the role command ............................................................ 151
Table 104 – Value format for the minimum storage commands .................................... 151
Table 105 – Value format for the required attributes command ..................................... 152
Table 106 – Encapsulated Vendor-Specific Option-Data fields ..................................... 160
Table 107 – Optional STUN attributes used in Binding Request messages ................... 166
Table 108 – UDPLightweightNotification arguments .................................................... 200
Table 109 – ParameterStruct definition .......................................................................... 201

November 2013 © The Broadband Forum. All rights reserved. Page 13 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

List of Figures
Figure 1 – Positioning in the End-to-End Architecture .................................................... 18
Figure 2 – Protocol stack .................................................................................................. 26
Figure 3 – Session Example .............................................................................................. 69
Figure 4 – Example Option specification ....................................................................... 135
Figure 5 – Example signed Voucher ............................................................................... 135
Figure 6 – Sequence of events for the “kick” mechanism .............................................. 140
Figure 7 – Signed package format .................................................................................. 142
Figure 8 – Download state diagram used for timeout model .......................................... 148
Figure 9 – Device-Gateway Association using DHCP Discover.................................... 158
Figure 10 – Device-Gateway Association Using DHCP Inform .................................... 159
Figure 11 – Binding discovery / maintenance from the primary source port ................. 173
Figure 12 – Binding Request from secondary source port for binding timeout discovery
................................................................................................................................. 174
Figure 13 – Binding change notification authenticated by the ACS .............................. 174
Figure 14 – Binding change notification not authenticated by the ACS ........................ 175
Figure 15 – UDP Connection Request ............................................................................ 175
Figure 16 – Proxy management terminology.................................................................. 180
Figure 17 – CPE Proxier and Proxied Device references ............................................... 181
Figure 18 – XMPP Connection Request Message Sequence .......................................... 187
Figure 19 – Connection Request: sent from ACS ........................................................... 193
Figure 20 – Successful Response to Connection Request: sent from CPE..................... 193
Figure 21 – 503 Error Response to Connection Request from ACS .............................. 193
Figure 22 – Authentication Error Response to Connection Request from ACS............. 193
Figure 23 – Turnaround time .......................................................................................... 206
Figure 24 – Router supporting 6 Proxied Devices .......................................................... 208
Figure 25 – XMPP Deployment Option – Stateful Firewall........................................... 218
Figure 26 – Message flows when the CPE LAN device starts up normally ................... 222
Figure 27 – Message flows when the CPE LAN device starts up normally ................... 224
Figure 28 – Message flows when the CPE LAN device starts up normally ................... 227

November 2013 © The Broadband Forum. All rights reserved. Page 14 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Executive Summary

A protocol for communication between a CPE and Auto-Configuration Server (ACS) that
encompasses secure auto-configuration as well as other CPE management functions
within a common framework.

November 2013 © The Broadband Forum. All rights reserved. Page 15 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

1 Introduction
Note – Sections 1 and 2 of this document are introductory and do not define requirements of this
protocol.
TR-069 describes the CPE WAN Management Protocol, intended for communication
between a CPE and Auto-Configuration Server (ACS). The CPE WAN Management
Protocol defines a mechanism that encompasses secure auto-configuration of a CPE, and
also incorporates other CPE management functions into a common framework.
This document specifies the generic requirements of the management protocol methods
which can be applied to any TR-069 CPE. Other documents specify the managed
objects, or data models, for specific types of devices or services.

1.1 Functional Components

The CPE WAN Management Protocol is intended to support a variety of functionalities
to manage a collection of CPE, including the following primary capabilities:
 Auto-configuration and dynamic service provisioning
 Software/firmware image management
 Software module management
 Status and performance monitoring
 Diagnostics

1.1.1 Auto-Configuration and Dynamic Service Provisioning

The CPE WAN Management Protocol allows an ACS to provision a CPE or collection of
CPE based on a variety of criteria.
The provisioning mechanism allows CPE provisioning at the time of initial connection to
the broadband access network, and the ability to re-provision or re-configure at any
subsequent time. This includes support for asynchronous ACS-initiated re-provisioning
of a CPE.
The identification mechanisms included in the protocol allow CPE provisioning based
either on the requirements of each specific CPE, or on collective criteria such as the CPE
vendor, model, software version, or other criteria.
The protocol also provides optional tools to manage the CPE-specific components of
optional applications or services for which an additional level of security is required to
control, such as those involving payments. The mechanism for control of such
applications and services is the Software Module Management mechanism as defined in
A.4.1.10 (ChangeDUState RPC), A.4.2.3 (DUStateChangeComplete RPC), and described
in Appendix II / TR-157 Amendment 3 [29].
The provisioning mechanism allows straightforward future extension to allow
provisioning of services and capabilities not yet included in this version of the
specification.

November 2013 © The Broadband Forum. All rights reserved. Page 16 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

1.1.2 Software/Firmware Image Management

The CPE WAN Management Protocol provides tools to manage downloading of CPE
software/firmware image files. The protocol provides mechanisms for version
identification, file download initiation (ACS initiated downloads and optional CPE
initiated downloads), and notification of the ACS of the success or failure of a file
download.

1.1.3 Software Module Management

The CPE WAN Management Protocol enables an ACS to manage modular software and
execution environments on a CPE. Capabilities provided include the ability to install,
update, and uninstall software modules as well as notification to the ACS of success or
failure of each action. The protocol also provides support to start and stop applications
on the CPE, enable and disable execution environments, and inventory the software
modules available on the device.

1.1.4 Status and Performance Monitoring

The CPE WAN Management Protocol provides support for a CPE to make available
information that the ACS may use to monitor the CPE’s status and performance statistics.
It also defines a set of mechanisms that allow the CPE to actively notify the ACS of
changes to its state.

1.1.5 Diagnostics
The CPE WAN Management Protocol provides support for a CPE to make available
information that the ACS may use to diagnose and resolve connectivity or service issues
as well as the ability to execute defined diagnostic tests.

1.2 Positioning in the End-to-End Architecture

The ACS is a server that resides in the network and manages devices in or at the
subscriber premises. The CPE WAN Management Protocol may be used to manage both
DSL B-NTs and other types of CPE, including stand-alone routers and LAN-side client
devices. It is agnostic to the specific access medium utilized by the service provider,
although it does depend on IP-layer connectivity having been established by the device.
Note – in the case of a B-NT, TR-046 [2] describes the overall framework for B-NT auto-
configuration, and TR-062 [3] and TR-044 [4] define the ATM layer and IP layer auto-
configuration procedures. Other types of broadband CPE should make use of the protocols
appropriate to their network architectures in order to obtain IP connectivity.
Note – where the CPE WAN Management Protocol is used to manage both a B-NT (or other
Internet Gateway Device), and a LAN-side client device operating behind that B-NT (or other
Internet Gateway Device), Annex F defines a mechanism to allow the ACS to associate the two so
that they may be managed together.
Note – CPE Implementations might exist where the CPE WAN Management Protocol contains
more than one CWMP Endpoint. Proxy management via the Virtual CWMP Device Mechanism is
one such case.

November 2013 © The Broadband Forum. All rights reserved. Page 17 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Figure 1 – Positioning in the End-to-End Architecture

OSS/BSS

Managed LAN
Device
Policy
Scope of CPE WAN Management
Protocol (CWMP):
ACS Southbound Interface

Call Managed LAN

Center Device
Managed Internet
Auto-Configuration
Gateway Device
Server (ACS)
Managed LAN
ACS Northbound Interface Device

1.3 Security Goals

The CPE WAN Management Protocol is designed to provide a high degree of security.
The security model is also designed to be scalable. It is intended to allow basic security
to accommodate less robust CPE implementations, while allowing greater security for
those that can support more advanced security mechanisms. In general terms, the
security goals of the CPE WAN Management Protocol are as follows:
 Prevent tampering with the management functions of a CPE or ACS, or the
transactions that take place between a CPE and ACS.
 Provide confidentiality for the transactions that take place between a CPE and ACS.
 Allow appropriate authentication for each type of transaction.
 Prevent theft of service.

1.4 Architectural Goals

The protocol is intended to provide flexibility in the connectivity model. The protocol is
intended to provide the following:
 Allow both CPE and ACS initiated connection establishment, avoiding the need for a
persistent connection to be maintained between each CPE and an ACS.
 The functional interactions between the ACS and CPE should be independent of
which end initiated the establishment of the connection. In particular, even where
ACS initiated connectivity is not supported, all ACS initiated transactions should be
able to take place over a connection initiated by the CPE.
 Allow one or more ACSs to serve a population of CPE, which may be associated with
one or more service providers.
The protocol is intended to support discovery and association of ACS and CPE:

November 2013 © The Broadband Forum. All rights reserved. Page 18 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

 Provide mechanisms for a CPE to discover the appropriate ACS for a given service
provider.
 Provide mechanisms to allow an ACS to securely identify a CPE and associate it with
a user/customer. Processes to support such association should support models that
incorporate user interaction as well as those that are fully automatic.
The protocol is intended to allow an ACS access to control and monitor various
Parameters associated with a CPE. The mechanisms provided to access these Parameters
are designed with the following premises:
 Different CPE may have differing capability levels, implementing different subsets of
optional functionality. Additionally, an ACS may manage a range of different device
types delivering a range of different services. As a result, an ACS must be able to
discover the capabilities of a particular CPE.
 An ACS must be able to control and monitor the current configuration of a CPE.
 Other control entities besides an ACS may be able to control some Parameters of a
CPE’s configuration (e.g., via LAN-side auto-configuration). As a result, the
protocol must allow an ACS to account for external changes to a CPE’s
configuration. The ACS should also be able to control which configuration
Parameters can be controlled via means other than by the ACS.
 The protocol should allow vendor-specific Parameters to be defined and accessed.
The protocol is intended to minimize implementation complexity, while providing
flexibility in trading off complexity vs. functionality. The protocol incorporates a
number of optional components that come into play only if specific functionality is
required. The protocol also incorporates existing standards where appropriate, allowing
leverage of off-the-shelf implementations.
The protocol is intended to be agnostic to the underlying access network.
The protocol is also designed to be extensible. It includes mechanisms to support future
extensions to the standard, as well as explicit mechanisms for vendor-specific extensions.

1.5 Assumptions
Some assumptions made in defining the CPE WAN Management Protocol are listed
below:
 All CPE regardless of type (bridge1, router, or other) obtain an IP address in order to
communicate with an ACS.
 A CWMP Endpoint can interact with a single ACS at a time. At any time, a CWMP
Endpoint is aware of exactly one ACS with which it can connect. (Note: a collection
of ACSs behind a load balancer is considered a single ACS for the purposes of this
document.)

1
In the case of a bridge, the CPE must establish IP-layer connectivity specifically for management communication.
The mechanism used to establish this connectivity would depend on the specific network architecture. For
example, a DSL bridge may connect using IPoE with DHCP for address allocation, or may connect using PPPoE.

November 2013 © The Broadband Forum. All rights reserved. Page 19 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

1.6 Terminology
The following terminology is used throughout the series of documents defining the CPE
WAN Management Protocol.
ACS Auto-Configuration Server. This is a component in the broadband
network responsible for auto-configuration of the CPE for advanced
services.
Action An explicitly triggered transition in the Software Module state model;
e.g. Install, Update, Uninstall, Start, Stop, etc. (see Appendix II/TR-157
[29])
Applied A change to the CPE’s configuration has been Applied when the CPE
has stopped using the previous configuration and begun using the new
configuration.
B-NT Broadband-Network Termination. A specific type of Broadband CPE
used in DSL networks.
Committed A change to the CPE’s configuration has been Committed when the
change has been fully validated, the new configuration appears in the
configuration Data Model for subsequent ACS operations to act on, and
the change will definitely be Applied in the future, as required by the
protocol specification.
Connection The ACS action of requesting a CPE to start a CWMP Session, as defined
Request in “3.2.2 ACS Connection Initiation.”
CPE Customer Premises Equipment; refers to a TR-069-compliant device and
therefore covers both Internet Gateway Devices and LAN-side end
devices. A CPE contains at least one CWMP Endpoint.
CPE Proxier A CPE that is capable of proxying the communication between an ACS
and a Proxied Device. There are two strategies for proxy management:
Virtual CWMP Device Mechanism and Embedded Object Mechanism.
CR-Aware A CPE in CR-Aware Standby is able to receive Connection Requests and
Standby to accept or reject them.
CWMP CPE WAN Management Protocol (the subject of this standard).
CWMP A CWMP termination point used by a CPE for Session communication
Endpoint with the ACS. This term is used interchangeably with CPE unless
specifically defining behavior where a CPE supports multiple CWMP
Endpoints
Data Model A hierarchical set of Parameters that define the managed Objects
accessible via TR-069 for a particular Device or service.
Deployment An entity that can be individually deployed on the Execution
Unit Environment. A Deployment Unit can consist of functional Execution
Units and/or configuration files and/or other resources.
Device Used interchangeably with CPE.

November 2013 © The Broadband Forum. All rights reserved. Page 20 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

DT Instance Device Type Schema instance document. This is an XML document that
conforms to the DT Schema and to any additional rules specified in or
referenced by the DT Schema.
DT Schema Device Type Schema. This is the XML Schema that is used for
describing a Device’s supported data model (see Annex B/TR-106 [13]).
Embedded A proxy management strategy where the CPE Proxier embeds the details
Object of the Proxied Device within the Data Model. The Proxied Device will
Mechanism appear to be integrated into the CPE Proxier.
Event An indication that something of interest has happened that requires the
CPE to notify the ACS.
Execution A software platform that enables the dynamic loading and unloading of
Environment Software Modules. Typical examples include Linux, OSGi, .NET, and
Java ME. Some Execution Environments enable the sharing of resources
amongst modules.
Execution A functional entity that, once started, initiates processes to perform tasks
Unit or provide services, until it is stopped. Execution Units are deployed by
Deployment Units. The following list of concepts could be considered an
Execution Unit: services, scripts, software components, libraries, etc.
Forced A Parameter whose definition requires it to be included with every
Inform Inform RPC.
Parameter
Instance A writeable string that uniquely identifies an instance within a Multi-
Alias Instance Object.
Instance A value that uniquely identifies an instance within a Multi-Instance
Identifier Object. It is either an Instance Number or an Instance Alias.
Instance A read-only positive integer (>=1) that uniquely identifies an instance
Number within a Multi-Instance Object.
Internet A CPE device, typically a broadband router, that acts as a gateway
Gateway between the WAN and the LAN.
Device
Multi- An Object that can have multiple instances, all of which have the same
Instance structure and are located at the same level within the name hierarchy.
Object Each instance is identified by an Instance Identifier.
Object An internal node in the name hierarchy, i.e., a node that can have Object
or Parameter children. An Object name is a Path Name.
Parameter A name-value pair that represents part of a CPE’s configuration or status.
A Parameter name is a Path Name.
Path Name A name that has a hierarchical structure similar to files in a directory,
with each level separated by a “.” (dot). References an Object or a
Parameter.

November 2013 © The Broadband Forum. All rights reserved. Page 21 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Partial Path A Path Name that ends with a “.” (dot). References an Object and
Name represents a subset of the name hierarchy.
Periodic A time when the CPE has to send a Periodic Inform.
Contact
Periodic An Inform message including the “2 PERIODIC” event.
Inform
Proxied An endpoint that communicates indirectly with an ACS via a CPE
Device Proxier.
RPC Remote Procedure Call.
Scheduled A specific time, resulting from a previous ACS request, when the CPE
Contact has to send an Inform. This does not include Periodic Informs.
Seen Missing A CPE has been Seen Missing by the ACS when that CPE has missed a
Periodic Contact or Scheduled Contact or when the ACS has failed to get
a response to a Connection Request. A CPE cannot determine whether it
has been Seen Missing.
Session A contiguous sequence of CWMP Transactions between a CWMP
Endpoint and an ACS. Note that a Session may span multiple TCP
connections.
Software The common term for all software (other than firmware) that will be
Module installed on an Execution Environment, including the concepts of
Deployment Units and Execution Units.
STB Set Top Box. This CPE contains Audio and Video decoders and is
intended to be connected to Analog TV and / or Home Theaters.
Timer- A CPE in Timer-Aware Standby is able to wake up to handle Periodic
Aware Contacts and Scheduled Contacts. Partial Timer-Aware Standby is
Standby possible (CPE waking up only for Scheduled Contacts, for example).
Transaction A message exchange between a CWMP Endpoint and an ACS consisting
of a single request followed by a single response, initiated either by the
CPE or ACS.
Virtual A proxy management strategy where the CPE Proxier creates a virtual
CWMP CWMP environment for the Proxied Device. The CPE Proxier provides
Device a separate CWMP Endpoint for each such Proxied Device, which will
Mechanism therefore appear and be managed like a standalone CWMP enabled CPE.
VoIP A Voice over IP CPE that acts as the initiation/termination point for
Endpoint VoIP calls. Examples of Endpoints include VoIP phones and analog
terminal adapters (ATAs).

1.7 Abbreviations
This Technical Report defines the following abbreviations:

ACL Access control list

November 2013 © The Broadband Forum. All rights reserved. Page 22 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

ACS Auto-Configuration Server

ADSL Asymmetric Digital Subscriber Line
AES Advanced Encryption Standard
ASCII American Standard Code for Information Interchange
ATA Analog terminal adapter
ATM Asynchronous Transfer Mode
BOOTP Boot Strap Protocol
CGI Common Gateway Interface
CN Common Name
CPE Customer Premise Equipment
CR Connection Request
CSRF Cross-site request forgery
CWMP CPE WAN Management Protocol
DHCP Dynamic Host Configuration Protocol
DNS Domain Name System
DSL Digital Subscriber Line
DSM-CC Digital storage media command and control
DT Device Type
DU Deployment Unit
EE Execution Environment
EU Execution Unit
FLUTE File Delivery over Unidirectional Transport
FTP File transfer Protocol
HMAC Hash-based Message Authentication Code
HTML Hypertext Markup Language
HTTP Hypertext Transfer Protocol
HTTPS Hypertext Transfer Protocol over Secure Socket Layer
IANA Internet Assigned Numbers Authority
ID Identifier
IP Internet Protocol
IPv6 Internet Protocol version 6
ISO International Organization for Standardization
LAN Local Area Network
LSB Least significant bit
MD5 Message-Digest algorithm 5
NAT Network Address Translation
NTP Network Time Protocol
NT Network Termination
OSGi OSGi Alliance (former Open Services Gateway initiative)
OUI Organizationally Unique Identifier
PKCS Public Key Cryptography Standards
QoS Quality of Service
RFC Request for Proposal
RPC Remote Procedure Call
RSA Rivest, Shamir and Adleman (crypto system)
SASL Simple Authentication and Security Layer

November 2013 © The Broadband Forum. All rights reserved. Page 23 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

SFTP SSH File Transfer Protocol

SHA1 Secure Hash Algorithm 1
SNMP Simple Network Management Protocol
SNTP Simple Network Time Protocol
SOAP Simple Object Access Protocol
SSH Secure Shell
SSL Secure Socket Layer
STB Set Top Box
STUN Session Traversal Utilities for NAT
TCP Transmission Control Protocol
TFTP Tiny File transfer Protocol
TLS Transport Layer Security
TLV Type length value
TR Technical Report
TTL Time to Live
TV Television
UDP User Datagram Protocol
UPnP Universal Plug and Play
UPnP DM Universal Plug and Play Device Management
UPnP IGD Universal Plug and Play Internet Gateway Device
URI Uniform Resource Identifier
URL Universal Resource Locator
URN Uniform Resource Name
UTC Coordinated Universal Time
UTF Universal Multiple-Octet Coded Character Set Transformation Format
UUID Universally Unique Identifier
VoIP Voice over Internet Protocol
WAN Wide Area Network
XML Extensible Markup Language
XMPP Extensible Messaging and Presence Protocol
XSD XML Schema
XSS Cross-Site Scripting

1.8 Document Conventions

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in
this document are to be interpreted as described in [1].
The key word “DEPRECATED” refers to a protocol feature, e.g. an RPC Method or
Event Type, that is defined and valid in the current version of the standard but is not
strictly necessary, e.g. because another more powerful feature has been defined. Such
features SHOULD NOT be used; they might be removed from the next major version of
the protocol.
The key word “OBSOLETED” refers to a protocol feature, e.g. an RPC Method or Event
Type, that meets the requirements for being DEPRECATED, and in addition is obsolete.
Such protocol features MUST NOT be used; they might be removed from a later minor

November 2013 © The Broadband Forum. All rights reserved. Page 24 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

version of the protocol, without this being regarded as breaking backwards compatability
rules.

November 2013 © The Broadband Forum. All rights reserved. Page 25 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

2 Architecture
2.1 Protocol Components
The CPE WAN Management Protocol comprises several components that are unique to
this protocol, and makes use of several standard protocols. The protocol stack defined by
the CPE WAN Management Protocol is shown in Figure 2. A brief description of each
layer is provided in Table 1. Note that the CPE and ACS must adhere to the requirements
of the underlying standard protocols unless otherwise specified.
Figure 2 – Protocol stack

CPE/ACS Management Application

RPC Methods

SOAP

HTTP

SSL/TLS

TCP/IP

Table 1 – Protocol layer summary

Layer Description
CPE/ACS Application The application uses the CPE WAN Management Protocol on the CPE and ACS,
respectively. The application is locally defined and not specified as part of the CPE
WAN Management Protocol.
RPC Methods The specific RPC methods that are defined by the CPE WAN Management Protocol.
These methods are specified in Annex A.
SOAP A standard XML-based syntax used here to encode remote procedure calls. Specifically
SOAP 1.1, as specified in [9].
HTTP HTTP 1.1, as specified in [6].
TLS The standard Internet transport layer security protocol. Specifically, TLS 1.2 (Transport
Layer Security) as defined in [11] (or a later version). Note that previous versions of this
specification referenced SSL 3.0 and TLS 1.0.
TCP/IP Standard TCP/IP.

November 2013 © The Broadband Forum. All rights reserved. Page 26 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

2.2 Security Mechanisms

The CPE WAN Management Protocol is designed to allow a high degree of security in
the interactions that use it. The CPE WAN Management Protocol is designed to prevent
tampering with the transactions that take place between a CPE and ACS, provide
confidentiality for these transactions, and allow various levels of authentication.
The following security mechanisms are incorporated in this protocol:
 The protocol supports the use of TLS for communications transport between CPE and
ACS. This provides transaction confidentiality, data integrity, and allows certificate-
based authentication between the CPE and ACS.
 The HTTP layer provides an alternative means of CPE and ACS authentication based
on shared secrets. Note that the protocol does not specify how the shared secrets are
learned by the CPE and ACS.

2.3 Architectural Components

2.3.1 Parameters
The RPC Method Specification (see Annex A) defines a generic mechanism by which an
ACS can read or write Parameters to configure a CPE and monitor CPE status and
statistics. Parameters for various classes of CPE are defined in separate documents. At
the time of writing the following standards define TR-069 data models.
 TR-098: Internet Gateway Device Data Model for TR-069 [24]
 TR-104: Provisioning Parameters for VoIP CPE [25]
 TR-135: Data Model for a TR-069 Enabled STB [26]
 TR-140: TR-069 Data Model for Storage Service Enabled Devices [27]
 TR-143: Enabling Network Throughput Performance Tests and Statistical
Monitoring [28]
 TR-157: Component Objects for CWMP [29]
 TR-181: Device Data Model for TR-069 [31] and [32]
 TR-196: Femto Access Point Service Data Model [30]
Each Parameter consists of a name-value pair. The name identifies the particular
Parameter. The value of a Parameter may be one of several defined data types (see TR-
106 [13]).
Parameters may be defined as read-only or read-write. Read-only Parameters may be
used to allow an ACS to determine specific CPE characteristics, observe the current state
of the CPE, or collect statistics. Writeable Parameters allow an ACS to customize
various aspects of the CPE’s operation. All writeable Parameters must also be readable
although those that contain confidential user information, e.g. passwords, may return
empty values when read (this is specified in the corresponding data model definition).
The value of some writeable Parameters may be independently modifiable through means

November 2013 © The Broadband Forum. All rights reserved. Page 27 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

other than the interface defined in this specification (e.g., some Parameters may also be
modified via a LAN side auto-configuration protocol).
Because other protocols (as well as subscriber action) may independently modify the
device configuration, the ACS cannot assume that it is the only entity modifying device
configuration. Additionally, it is possible that a LAN-side mechanism could alter device
configuration in such a way that it contravenes the intended ACS-supplied configuration.
Care should be taken in the implementation of both WAN and LAN-side auto-
configuration mechanisms, as well as subscriber-facing interfaces, to limit the instances
of such an occurrence.
The protocol supports a discovery mechanism that allows an ACS to determine what
Parameters a particular CPE supports, allowing the definition of optional Parameters as
well as supporting straightforward addition of future standard Parameters.
The protocol also includes an extensibility mechanism that allows use of vendor-specific
Parameters in addition to those defined in this specification.

2.3.2 File Transfers

The RPC Method Specification (see Annex A) defines mechanisms to facilitate file
transfers for a variety of purposes, such as downloading firmware upgrades or vendor-
specific configuration files, (optionally) installing or updating software modules, and
(optionally) uploading configuration or log files from the device.
File transfers can be performed by means of Unicast or (for downloads) Multicast
transport protocols. Unicast protocols include HTTP/HTTPS, FTP, SFTP and TFTP.
Multicast protocols include FLUTE and DSM-CC. Support for HTTP/HTTPS is
mandatory, and protocols other than those listed here can be supported.
When a file transfer is initiated by the ACS via any of the method calls that can cause a
file transfer, the CPE is provided with the location of the file (or possibly files in the case
of a software module installation or update) to be transferred, or details of the Multicast
group to join (for Multicast downloads). The CPE then performs the transfer(s), and
notifies the ACS of success or failure.
Downloads may be optionally initiated by a CPE. In this case, the CPE first requests a
download of a particular file type from the ACS. The ACS may then respond by
initiating the download following the same steps as an ACS-initiated download.
File transfers may also be optionally initiated by an external event, e.g. a Multicast
firmware availability announcement or user-initiated software module updates. In this
case, the CPE performs the transfer autonomously, and notifies the ACS of the success or
failure.

2.3.3 CPE Initiated Sessions

The RPC Method Specification (see Annex A) defines a mechanism that allows a CPE to
inform a corresponding ACS of various conditions, and to ensure that CPE-to-ACS
communication will occur with some minimum frequency.
This includes mechanisms to establish communication upon initial CPE installation in
order to ‘bootstrap’ initial customized Parameters into the CPE. It also includes a

November 2013 © The Broadband Forum. All rights reserved. Page 28 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

mechanism to establish periodic communication with the ACS on an ongoing basis, or

when events occur that must be reported to the ACS (such as when the broadband IP
address of the CPE changes).
In each case, when communication is established the CPE identifies itself uniquely via
manufacturer and serial number information (and optional product class identifier) so that
the ACS knows which CPE it is communicating with and can respond in an appropriate
way.

2.3.4 Asynchronous ACS Initiated Sessions

An important aspect of service auto-configuration is the ability for the ACS to inform the
CPE of a configuration change asynchronously. This allows the auto-configuration
mechanism to be used for services that require near-real-time reconfiguration of the CPE.
For example, this may be used to provide an end-user with immediate access to a service
or feature they have subscribed to, without waiting for the next periodic contact.
The CPE WAN Management Protocol incorporates a mechanism for the ACS to issue a
Connection Request to the CPE at any time, instructing it to establish a communication
Session with the ACS.
While the CPE WAN Management Protocol also allows polling by the CPE in lieu of
ACS-initiated connections, the CPE WAN Management Protocol does not rely on polling
or establishment of persistent connections from the CPE to provide asynchronous
notification.
The basic mechanism defined in the CPE WAN Management Protocol to enable
asynchronous ACS initiated communication assumes direct IP addressability of the CPE
from the ACS. An alternative mechanism is defined in Annex K, which accommodates
CPE that are not directly addressable by the ACS.

November 2013 © The Broadband Forum. All rights reserved. Page 29 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

3 Procedures and Requirements

This Section, along with the Annexes referenced in this Section, defines the normative
requirements of the CPE WAN Management Protocol.
This Section also references a number of standards and other specifications that form part
of the CPE WAN Management Protocol. Unless otherwise specified, the CPE and ACS
MUST adhere to the requirements of these referenced specifications.

3.1 ACS Discovery

The CPE WAN Management Protocol defines the following mechanisms that MAY be
used by a CPE to discover the address of its associated ACS:
1. The CPE MAY be configured locally with the URL of the ACS for each CWMP
Endpoint. For example, this MAY be done via a LAN-side CPE auto-configuration
protocol. If necessary, the CPE would use DNS to resolve the IP address of the ACS
from the host name component of the URL.
2. As part of the IP layer auto-configuration, a DHCP server on the access network
MAY be configured to include the ACS URL as a DHCP option [14] / [22] / [35]. If
necessary, the CPE would use DNS to resolve the IP address of the ACS from the
host name component of the URL. In this case additional DHCP options MAY be
used to set:
 The ProvisioningCode, which MAY be used to indicate the primary service
provider and other provisioning information to the ACS.
 The CWMPRetryMinimumWaitInterval, which MAY be used to set the initial
value of the CWMP session retry minimum wait interval, as specified in Section
3.2.1.1.
 The CWMPRetryIntervalMultiplier, which MAY be used to set the initial value of
the CWMP session retry interval multiplier, as specified in Section 3.2.1.1.
A CPE identifies itself to the DHCP server as supporting this method by including the
string “dslforum.org” (all lower case) anywhere in the DHCPv4 Vendor Class
Identifier (option 60), in the DHCPv4 V-I Vendor Class Option (option 124) or in a
DHCPv6 Vendor Class (option 16) vendor-class-data item.
The CPE MAY include either DHCPv4 option 43 or DHCPv4 option 125 (not both)
in a DHCPv4 parameter request list (option 55) in order to indicate support for and to
request option 43 or option 125. If the CPE does not use option 55 in this way, the
server can assume that it supports and requests option 43 (not option 125). Similarly,
the CPE MAY include DHCPv6 option 17 in a DHCPv6 Option Request Option
(option 6).
The CPE MAY use the values received from the DHCP server in the Vendor Specific
Information (DHCPv4 option 43 / DHCPv4 option 125 / DHCPv6 option 17) to set
the corresponding Parameters as listed in Table 2. If both DHCPv4 options are
received, the CPE MUST use the DHCP option that it included in the DHCPv4
parameter request list (option 55); unless it did not use option 55, in which case the

November 2013 © The Broadband Forum. All rights reserved. Page 30 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

CPE MUST use the DHCPv4 option 43 values. If both DHCPv4 and DHCPv6
options are received, the CPE MUST use the DHCPv6 option over the DHCPv4
option. This DHCP option is encoded as a list of one or more Encapsulated Vendor-
Specific Options in the format defined in [14] / [22] / [35]. This list MAY include
other vendor-specific options in addition to those listed here.
DHCP messages that include IANA Enterprise Numbers, i.e. DHCPv4 options 124 /
125 and DHCPv6 options 16 / 17, MUST use the Broadband Forum IANA Enterprise
Number, which is 3561 decimal (the “ADSL Forum” entry in the IANA Private
Enterprise Numbers registry [18]).
If the CPE obtained an ACS URL through DHCP and it cannot reach the ACS, the
CPE MUST use DHCP to re-discover the ACS URL. The CPE MUST consider the
ACS unreachable if it cannot establish a TCP connection to it for 300 seconds at each
of the IP addresses to which the ACS URL resolves. If the CPE does not receive a
DHCP reply, it MUST attempt to retry according to [20] / [35].
When the CPE needs to contact the ACS, it MUST use the DHCP discovery
mechanism in the following scenarios:
 If the CPE has an empty value for the ManagementServer.URL Parameter, or
 If the CPE is unable to contact the ACS and the CPE originally (the first
successful time after the most recent factory reset) obtained its ACS URL through
DHCP.
This behavior enables the CPE to go back to the use of DHCP for finding the ACS if
an ACS URL had not been pre-configured in the CPE. For example, this can handle
the situation of setting an incorrect ACS URL on the CPE. This behavior is not
meant as an ACS failover mechanism.
The CPE MUST remember the mechanism it used to locate the ACS after each
factory reset. If the CPE did not use DHCP to discover the ACS URL, then it
SHOULD NOT fall back to using DHCP for ACS discovery. If the CPE originally
used DHCP for ACS discovery, then when it fails to contact the ACS, it MUST
perform re-discovery via DHCP. The last requirement holds even if the ACS URL
has been subsequently set through a non-DHCP mechanism.
Table 2 – Encapsulated Vendor Specific Options
2
Encapsulated Encapsulated Vendor- Parameter
Option Specific Option number
DHCPv4 DHCPv4 DHCPv6
Option Option Option
43 125 17
URL of the ACS 1 11 1 ManagementServer.URL
Provisioning code 2 12 2 DeviceInfo.ProvisioningCode
CWMP retry mini- 3 13 3 ManagementServer.CWMPRetryMinimumWait-
mum wait interval Interval
CWMP retry 4 14 4 ManagementServer.CWMPRetryIntervalMultiplier
interval multiplier

2
As defined in [24], [31], and [32].

November 2013 © The Broadband Forum. All rights reserved. Page 31 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

All the encapsulated option values MUST be represented as strings and MUST be
valid values for their corresponding Parameters. The specified URL MUST be an
absolute URL. The encapsulated option values MUST NOT be null terminated. If
the CPE receives an encapsulated option value that is null terminated, the CPE MUST
accept the value provided, and MUST NOT interpret the null character as part of the
value.
3. The CPE MAY have a default ACS URL that it MAY use if no other URL is
provided to it.
The ACS URL MUST be in the form of a valid HTTP or HTTPS URL [6]. Use of an
HTTPS URL indicates that the CPE MUST establish an SSL or TLS connection to the
ACS.
Once the CPE has established a connection to the ACS via a CWMP Endpoint, the ACS
MAY at any time modify the ACS URL Parameter stored within the CPE (Management-
Server.URL, as defined in [24], [31], and [32]). Once modified, the CPE MUST use the
modified URL for all subsequent connections to the ACS.
The “host” portion of the ACS URL is used by the CPE for validating the certificate from
the ACS when using certificate-based authentication. Because this relies on the accuracy
of the ACS URL, the overall security of this protocol is dependent on the security of the
ACS URL.
The CPE SHOULD restrict the ability to locally configure the ACS URL to mechanisms
that require strict security. The CPE MAY further restrict the ability to locally set the
ACS URL to initial setup only, preventing further local configuration once the initial
connection to an ACS has successfully been established such that only its existing ACS is
permitted subsequently to change this URL.
The use of DHCP for configuration of the ACS URL SHOULD be limited to situations in
which the security of the link between the DHCP server and the CPE can be assured by
the service provider. Since DHCP does not itself incorporate a security mechanism, other
means of ensuring this security SHOULD be provided.
The ACS URL MAY contain a DNS hostname or an IP address. When resolving the
ACS hostname, the DNS server might return multiple IP addresses. In this case, the CPE
SHOULD randomly choose an IP address from the list. When the CPE is unable to reach
the ACS, it SHOULD randomly select a different IP address from the list and attempt to
contact the ACS at the new IP address. This behavior ensures that CPEs will balance
their requests between different ACSs if multiple IP addresses represent different ACSs.
The CPE MUST NOT cache the DNS server response beyond the duration of time to live
(TTL) returned by DNS server unless it cannot contact the DNS server for an update.
This behavior is required by DNS RFC 1034 [5] and provides an opportunity for the DNS
server to update stale data.
It is further RECOMMENDED that the CPE implements affinity to a particular ACS IP
address. Affinity to a given IP address means that the CPE will attempt to use the same
IP address for as long as it can contact the ACS at this address. This creates a more
stable system and can allow the ACS to perform better due to better caching. To

November 2013 © The Broadband Forum. All rights reserved. Page 32 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

implement the affinity the CPE SHOULD store to persistent storage the last successfully
used IP address and the list of IP addresses from which it was selected. The CPE
SHOULD continue to perform DNS queries as normal, but SHOULD continue using the
same IP address for as long as it can contact the ACS and for as long as the list of IP
addresses returned by the DNS does not change. The CPE SHOULD select a new IP
address whenever the list of IP addresses changes or when it cannot contact the ACS.
This provides an opportunity for service providers to reconfigure their network.
Port 7547 has been assigned by IANA for the CPE WAN Management Protocol (see
[17]), and the ACS MAY use this port in its URL.

3.2 Connection Establishment

3.2.1 CPE Connection Initiation

The CPE MAY at any time initiate a connection to the ACS via a CWMP Endpoint using
the pre-determined ACS address (see Section 3.1). A CPE MUST establish a connection
to the ACS and issue the Inform RPC method (following the procedures described in
Section 3.7.1.1) under the following conditions:
 The first time the CPE establishes a connection to the access network on initial
installation
 On power-up or reset
 Once every ManagementServer.PeriodicInformInterval (for example, every 24
hours)
 When so instructed by the optional ScheduleInform method
 Whenever the CPE receives a valid Connection Request from an ACS (see
Section 3.2.2)
 Whenever the URL of the ACS changes
 Whenever a Parameter is modified that is required to initiate an Inform on change.
 Whenever the value of a Parameter that the ACS has marked for “Active
notification” via the SetParameterAttributes method is modified by an external
cause (a cause other than the ACS itself). Parameter changes made by the ACS
itself via SetParameterValues MUST NOT cause a new Session to be initiated. If
a Parameter is modified more than once before the CPE is able to initiate a
Session to perform the notification, the CPE MUST perform only one notification.
If a Parameter is modified by an external cause while a Session is in progress, the
change causes a new Session to be established after the current Session is
terminated (it MUST NOT affect the current Session).
In order to avoid excessive traffic to the ACS, a CPE MAY place a locally
specified limit on the frequency of Parameter change notifications. This limit
SHOULD be defined so that it is exceeded only in unusual circumstances. If this
limit is exceeded, the CPE MAY delay by a locally specified amount initiation of
a Session to notify the ACS. After this delay, the CPE MUST initiate a Session to

November 2013 © The Broadband Forum. All rights reserved. Page 33 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

the ACS and indicate all relevant Parameter changes (those Parameters that have
been marked for notification) that have occurred since the last such notification.
 Whenever a download or upload completes (either successfully or
unsuccessfully), provided that CPE policy indicates that the ACS needs to be
notified of the download or upload completion.
The ACS MUST always be notified of the completion of downloads or uploads
that were specifically requested by the ACS.
CPE policy MUST determine whether to notify the ACS of the completion of
downloads or uploads that were not specifically requested by the ACS.
Note – this CPE policy is remotely configurable via the parameters defined within the
ManagementServer.AutonomousTransferCompletePolicy object. For example, the CPE might be
configured to notify the ACS only if a download or upload (not requested by the ACS) was not
completed successfully.

 Whenever an unsuccessfully terminated Session is retried according to the session

retry policy specified in Section 3.2.1.1.
The CPE MUST NOT maintain an open connection to the ACS when no more
outstanding messages exist on the CPE or ACS. Refer to Section 3.7.1.4 for details of
CPE Session termination criteria.
3.2.1.1 Session Retry Policy
A CPE MUST retry failed Sessions to attempt to redeliver events that it has previously
failed to deliver and to allow the ACS to make additional requests in a timely fashion.
Section 3.7.1.5 details the rules for successful event delivery, for retrying event delivery,
and for discarding events after failing to deliver them. The CPE MUST keep track of the
number of times it has attempted to retry a failed Session.
If the CPE fails to establish a Session, this might be because the CPE supports CPE WAN
Management Protocol v1.1 (or later) and the ACS supports only v1.0. If this situation is
suspected (see Section 3.7.2.1), the CPE MUST revert to v1.0 when retrying the failed
Session.
A CPE MUST retry a failed Session after waiting for an interval of time specified in
Table 3 or when a new event occurs, whichever comes first. The CPE MUST choose the
wait interval by randomly selecting a number of seconds from a range given by the post-
reboot session retry count. When retrying a failed Session after an intervening reboot, the
CPE MUST reset the wait intervals it chooses from as though it were making its first
session retry attempt. In other words, if a Session is retried when a new event other than
BOOT occurs, it does not reset the wait interval, although the continued occurrence of
new events might cause Sessions to be initiated more frequently than shown in the table.
Regardless of the reason a previous Session failed or the condition prompting session
retry, the CPE MUST communicate to the ACS the session retry count.
The wait interval range is controlled by two Parameters, the minimum wait interval and
the interval multiplier, each of which corresponds to a data model Parameter, and which
are described in the table below.

November 2013 © The Broadband Forum. All rights reserved. Page 34 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

3 4
Descriptive Name Symbol Default Data Model Parameter Name
Minimum wait interval m 5 seconds ManagementServer.CWMPRetryMinimumWaitInterval
Interval multiplier k 2000 ManagementServer.CWMPRetryIntervalMultiplier

The factory default values of these Parameters MUST be the values that were hard-coded
in previous versions of the CPE WAN Management Protocol, i.e. the values from the
Default column. These values MAY be overridden by values obtained via DHCP, as
explained in Section 3.1. They MAY also be changed by the ACS at any time.
Beginning with the tenth post-reboot session retry attempt, the CPE MUST choose from
the fixed maximum range shown in Table 3. The CPE MUST continue to retry a failed
Session until it is successfully terminated or until the rules defined in the “Retry/Discard
Policy” column within Table 8 take precedence. Once a Session terminates successfully,
the CPE MUST reset the session retry count to zero and no longer apply session retry
policy to determine when to initiate the next Session.
Table 3 – Session Retry Wait Intervals
Post Reboot Default Wait Interval Range Actual Wait Interval Range
Session Retry (min-max seconds) (min-max seconds)
Count
#1 5-10 m – m.(k/1000)
#2 10-20 m.(k/1000) – m.(k/1000)2
#3 20-40 m.(k/1000)2 – m.(k/1000)3
#4 40-80 m.(k/1000)3 – m.(k/1000)4
#5 80-160 m.(k/1000)4 – m.(k/1000)5
#6 160-320 m.(k/1000)5 – m.(k/1000)6
#7 320-640 m.(k/1000)6 – m.(k/1000)7
#8 640-1280 m.(k/1000)7 – m.(k/1000)8
#9 1280-2560 m.(k/1000)8 – m.(k/1000)9
#10 and subsequent 2560-5120 m.(k/1000)9 – m.(k/1000)10

3.2.1.2 Use of random source port

Each time the CPE first connects to the ACS after rebooting, it SHOULD use a different
ephemeral TCP source port in order to avoid the possibility of reusing the same port that
it used last time. Reuse of the same port could cause the ACS to reject the connection if
the elapsed time since the previous connection is less than the ACS’s configured TCP
TIME_WAIT value.
In order to minimize the probability that the same ephemeral port number is used on
successive occasions, the port SHOULD be selected using a strong randomization
mechanism.

3
These symbols are used in Table 3.
4
These are the values that were hard-coded in previous versions of the CPE WAN Management Protocol.

November 2013 © The Broadband Forum. All rights reserved. Page 35 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

3.2.2 ACS Connection Initiation

The ACS MAY at any time request that a CWMP Endpoint initiate a connection to the
ACS using the Connection Request mechanism. Support for this mechanism is
REQUIRED in a CPE, and is RECOMMENDED in an ACS.
This mechanism relies on the CPE being reachable by the ACS. If the CPE is behind a
firewall or if there is a NAT device between the ACS and CPE, the ACS might not be
able to access the CPE at all. Annex K defines a mechanism that allows an ACS to
contact a CPE that is not directly reachable by the ACS.
This mechanism relies on the ACS having had at least one prior communication with the
CWMP Endpoint in a CPE-initiated interaction. During this interaction, if the ACS
wishes to allow future ACS-initiated transactions, it would use the value of the
ManagementServer.ConnectionRequestURL Parameter (see [24], [31] , and [32]). If the
URL used for management access changes, the CPE MUST notify the ACS via an Inform
message.
Port 7547 has been assigned by IANA for the CPE WAN Management Protocol (see
[17]), and the CPE MAY use this port in the Connection Request URL.
3.2.2.1 Generic Connection Request Requirements
The Connection Request mechanism has the following generic requirements (meaning
that these requirements apply to any Connection Request communications independent of
the transport protocol being utiilzed):
 The CPE MUST accept Connection Requests from any source that has the correct
authentication parameters for the target CPE.
 The CPE SHOULD restrict the number of Connection Requests for a particular
CWMP Endpoint that it accepts during a given period of time in order to further
reduce the possibility of a denial of service attack. If the CPE chooses to reject a
Connection Request for this reason, the CPE MUST respond to that Connection
Request with a transport specific error.
 If the CPE successfully authenticates and responds to a Connection Request for a
particular CWMP Endpoint as described above, and if it is not already in a Session
for the requested CWMP Endpoint, then it MUST, within 30 seconds of sending the
response, attempt to establish a Session with the pre-determined ACS address (see
Section 3.1) in which it includes the “6 CONNECTION REQUEST” EventCode in
the Inform.
Note – in practice there might be exceptional circumstances that would cause a CPE to fail to
meet this requirement on rare occasions.

 If the ACS receives a successful response to a Connection Request but after at least
30 seconds the CPE has not successfully established a Session that includes the “6
CONNECTION REQUEST” EventCode in the Inform, the ACS MAY retry the
Connection Request to that CPE.
 If the CPE, once it successfully authenticates and responds to a Connection Request,
but before it establishes a Session to the ACS, receives one or more successfully
authenticated Connection Requests for the same CWMP Endpoint, the CPE MUST

November 2013 © The Broadband Forum. All rights reserved. Page 36 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

return a successful response for each of those Connection Requests, but MUST NOT
initiate any additional Sessions for the same CWMP Endpoint as a result of these
additional Connection Requests, regardless of how many it receives during this time.
 If the CPE is already in a Session with the ACS with at least one CWMP Endpoint
when it receives one or more Connection Requests, it MUST NOT terminate any
Session against any CWMP Endpoint prematurely as a result. The CPE MUST
instead take a transport specific alternative action.
This requirement holds for Connection Requests received any time during the interval
that the CPE considers itself in a Session with at least one CWMP Endpoint,
including the period in which the CPE is in the process of establishing the Session.
 The CPE MUST NOT reject a properly authenticated Connection Request for any
reason other than those described above. If the CPE rejects a Connection Request for
any of the reasons described above, it MUST NOT initiate a Session with the ACS as
a result of that Connection Request.
3.2.2.2 HTTP Specific Connection Request Requirements
The Connection Request mechanism also has the following requirements when traversing
over an HTTP transport:
 The Connection Request MUST use an HTTP 1.1 GET to a specific URL designated
by the CPE. The URL value is available as read-only Parameter on the CPE. The
path of this URL value SHOULD be randomly generated by the CPE so that it is
unique per CPE.
 The Connection Request MUST make use of HTTP, not HTTPS. The associated
URL MUST be an HTTP URL.
 No data is conveyed in the Connection Request HTTP GET. Any data that might be
contained SHOULD be ignored by the CPE.
 The CPE MUST use HTTP digest authentication [7] to authenticate the ACS before
proceeding—the CPE MUST NOT initiate a connection to the ACS due to an
unsuccessfully authenticated request.
 The CPE’s response to a successfully authenticated Connection Request MUST use
either a “200 (OK)” or a “204 (No Content)” HTTP status code. The CPE MUST
send this response immediately upon successful authentication, prior to it initiating
the resulting Session. The length of the entity-body (Section 7.2/RFC 2616 [6]) in the
HTTP response MUST be zero.
 The CPE SHOULD restrict the number of Connection Requests for a particular
CWMP Endpoint that it accepts during a given period of time in order to further
reduce the possibility of a denial of service attack. If the CPE chooses to reject a
Connection Request for this reason, the CPE MUST respond to that Connection
Request with an HTTP 503 status code (Service Unavailable). Furthermore, the CPE
SHOULD NOT include the HTTP Retry-After header in the response.
 If the CPE is already in a Session with the ACS with at least one CWMP Endpoint
when it receives one or more Connection Requests, it MUST NOT terminate any

November 2013 © The Broadband Forum. All rights reserved. Page 37 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Session against any CWMP Endpoint prematurely as a result. The CPE MUST
instead take one of the following HTTP-specific alternative actions:
 Reject each Connection Request by responding with an HTTP 503 status code
(Service Unavailable). In this case, the CPE SHOULD NOT include the HTTP
Retry-After header in the response.
 Following the completion of the CWMP Endpoint’s current Session, initiate
exactly one new Session at a time (regardless of how many Connection Requests
had been received during the previous Session) in which it includes the
“6 CONNECTION REQUEST” EventCode in the Inform. The Connection
Requests that are not accepted MUST be rejected (with an HTTP 503 status
code). If the new Session is for the CWMP Endpoint currently in Session, the
CPE MUST initiate the Session immediately after the existing Session is complete
and all changes from that Session have been applied.
 If the Connection Request is not for any CWMP Endpoint currently in Session,
the CPE MAY initiate a new Session with the requested CWMP Endpoint while
the existing Session is still active.
This requirement holds for Connection Requests received any time during the interval
that the CPE considers itself in a Session with at least one CWMP Endpoint,
including the period in which the CPE is in the process of establishing the Session.

3.3 Use of TLS and TCP

Note – previous versions of this specification referenced SSL 3.0 and TLS 1.0. These are no
longer mentioned in the text below, and SHOULD NOT be used.

The use of TLS to transport the CPE WAN Management Protocol is RECOMMENDED,
although the protocol MAY be used directly over a TCP connection instead. If TLS is
not used, some aspects of security are sacrificed. Specifically, TLS provides
confidentiality and data integrity, and allows certificate-based authentication in lieu of
shared secret-based authentication.
Certain restrictions on the use of TLS and TCP are defined as follows:
 The CPE SHOULD support TLS 1.2 [11] (or a later version).
 The CPE SHOULD communicate its capabilities to the ACS as specified in Appendix
E of RFC 5246 [11], allowing the ACS to choose the protocol.
 If the ACS URL has been specified as an HTTPS URL, the CPE MUST establish
secure connections to the ACS, and SHOULD use TLS 1.2 (or, if supported, a later
version).
Note – if the ACS does not support the version with which the CPE establishes the connection, it
might be necessary to negotiate an earlier TLS 1.x version, or even SSL 3.0. This implies that the
CPE has to support the mandatory cipher suites for all supported TLS or SSL versions.

November 2013 © The Broadband Forum. All rights reserved. Page 38 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Note – TLS_RSA_WITH_AES_128_CBC_SHA is the only mandatory TLS 1.2 cipher suite.

 RC4-based cipher suites MUST NOT be used with TLS 1.2.

 A CPE MUST be able to initiate outgoing connections to the ACS.
 An ACS MUST be able to accept CPE-initiated connections.
 If TLS 1.2 (or a later version) is used, the CPE MUST authenticate the ACS using the
ACS-provided certificate. Authentication of the ACS requires that the CPE MUST
validate the certificate against a root certificate, and that the CPE MUST ensure that
the value of the CN (Common Name) component of the Subject field in the certificate
exactly matches the host portion of the ACS URL known to the CPE (even if the host
portion of the ACS URL is an IP address). This MUST be a direct string comparison
between the CN and the host portion of the ACS URL. If either of these is in the
form of a hostname (rather than an IP address), this comparison MUST NOT involve
the IP address that the hostname resolves to.
To validate against a root certificate, the CPE MUST contain one or more trusted root
certificates that are either pre-loaded in the CPE or provided to the CPE by a secure
means outside the scope of this specification.
If as a result of an HTTP redirect, the CPE is attempting to access an ACS at a URL
different from its pre-configured ACS URL, the CPE MUST validate the CN
component of the ACS certificate against the host portion of the redirected ACS URL
rather than the pre-configured ACS URL.
A CPE capable of obtaining absolute time SHOULD wait until it has accurate
absolute time before contacting the ACS. If a CPE for any reason is unable to obtain
absolute time, it can contact the ACS without waiting for accurate absolute time. If a
CPE chooses to contact the ACS before it has accurate absolute time (or if it does not
support absolute time), it MUST ignore those components of the ACS certificate that
involve absolute time, e.g. not-valid-before and not-valid-after certificate restrictions.
 Support for CPE authentication using client-side certificates is OPTIONAL for both
the CPE and ACS. Such client-side certificates MUST be signed by an appropriate
chain. When client-side certificates are used to authenticate the CPE to the ACS, the
Common Name (CN) field in the CPE certificate MUST be one of the following two
types:
 Unique CPE client certificate. In this case, the value of the CN field MUST be
globally unique for each CPE. Specifically, the CN field MUST adhere to the
format recommended for the username/userid in Section 3.4.4.
Examples:
00D09E-0123456789
012345-STB-0123456789
012345-Set%2DTop%2DBox-0123456789

 Generic CPE client certificate. In this case, the value of the CN field MAY be the
same among a set of CPE, such as all CPE of a specific model from a given
vendor. The content of the CN field is not specified in this case.

November 2013 © The Broadband Forum. All rights reserved. Page 39 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

If generic CPE client certificates are used, the ACS SHOULD additionally
authenticate the CPE using HTTP basic or digest authentication to establish the
identity of a specific CPE.

3.4 Use of HTTP

SOAP messages are carried between a CPE and an ACS using HTTP 1.1 [6], where the
CPE acts as the HTTP client and the ACS acts as the HTTP server.
Note – the CPE WAN Management Protocol also uses HTTP for Connection Requests, where the
ACS acts as the HTTP client and the CPE acts as the HTTP server. This usage of HTTP is
described in Section 3.2.2

3.4.1 Encoding SOAP over HTTP

The encoding of SOAP over HTTP extends the HTTP binding for SOAP, as defined in
Section 6 of [9], as follows:
 A SOAP request from an ACS to a CPE is sent over an HTTP response, while the
CPE’s SOAP response to an ACS request is sent over a subsequent HTTP POST.
 When there is a SOAP response in an HTTP Request, or when there is a SOAP
Fault response in an HTTP Request, the SOAPAction header in the HTTP
Request MUST have no value (with no quotes), indicating that this header
provides no information as to the intent of the message. That is, it MUST appear
as follows:
SOAPAction:

 When an HTTP Request or Response contains a SOAP Envelope, the HTTP

Content-Type header MUST have a type/subtype of “text/xml”.
 An empty HTTP POST MUST NOT contain a SOAPAction header.
 An empty HTTP POST MUST NOT contain a Content-Type header.
 An HTTP response that contains any CPE WAN Management Protocol payload (a
SOAP request to the CPE, a successful SOAP response to the CPE, or a SOAP
fault response containing a Fault element defined in Section 3.4.7) MUST use the
HTTP status code 200 (OK).
Below is an example HTTP Response from an ACS containing a SOAP Request:
HTTP/1.1 200 OK
Content-Type: text/xml; charset="utf-8"
Content-Length: xyz

<soap:Envelope
xmlns:soap="http://schemas.xmlsoap.org/soap/envelope/"
xmlns:cwmp="urn:dslforum-org:cwmp-1-0">
<soap:Body>
<cwmp:Request>
<argument>value</argument>
</cwmp:Request>
</soap:Body>
</soap:Envelope>

November 2013 © The Broadband Forum. All rights reserved. Page 40 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Note – in the above example, the XML namespace prefixes used are only examples. The actual
namespace prefix values are arbitrary, and are used only to refer to a namespace declaration.
Note – in the above example, the CWMP namespace identifier “urn:dslforum-org:cwmp-1-0” is
only an example and is not necessarily the namespace that is defined by this specification.

3.4.2 Sessions
For a sequence of transactions forming a single Session, a CPE SHOULD maintain a
TCP connection that persists throughout the duration of the Session. Specifically, the
CPE MUST NOT initiate the closure of the TCP connection during the Session.
However, if the TCP connection is cleanly closed after an HTTP request/response round
trip, and if the Session has not otherwise terminated (either successfully or
unsuccessfully) at the time of the last HTTP response, the CPE MUST continue the
Session by sending the next HTTP request in a new TCP connection.
Note – use of a single TCP connection per Session is highly desirable, because re-negotiation of
connections uses additional resources (network sockets, network bandwidth, processing power),
which increases the chances of system overload and dropped Sessions, which in turn increases the
load.
After receiving an authentication challenge, the CPE MUST send the next HTTP request
(including the "Authorization" HTTP header) in the same TCP connection unless the
ACS specifically requested, via a "Connection: close" HTTP header, that the TCP
connection be closed5. In the latter case, the CPE MUST honor the ACS request, close
the TCP connection, and send the next HTTP request (including the "Authorization"
HTTP header) in a new TCP connection.
If the CPE for any reason fails to establish a TCP connection, fails to send an HTTP
message, or fails to receive an HTTP response, the CPE MUST consider the Session
unsuccessfully terminated. The CPE MUST wait a minimum of 30 seconds before
declaring a failure to establish a TCP connection, or failure to receive an HTTP response.
The ACS SHOULD make use of a session cookie to maintain session state as described
in [8]. The ACS SHOULD use only cookies marked for Discard, and SHOULD NOT
assume that a CPE will maintain a cookie beyond the duration of the Session.
To ensure that an ACS can make use of a session cookie, a CPE MUST support the use of
cookies as defined in [8] including the return of the cookie value in each subsequent
HTTP POST, with the exception that a CPE need not support storage of cookies beyond
the duration of a Session. The CPE MUST support the use of multiple cookies by the
ACS, and MUST make available at least 512 bytes for storage of cookies.
Note –old-style “Netscape” cookies might be used when dealing with an ACS that utilizes a
previous version of this specification.
When a Session is completed successfully or terminated unsuccessfully, a CPE MUST
close the associated TCP connection to the ACS.

5
This extra requirement is necessary because some ACS implementations might utilize the underlying TCP
connection as a mechanism to detect replay attacks (see the note in Section 3.4.5). Such implementations would
require the response to an authentication challenge to use the same TCP connection as the challenge.

November 2013 © The Broadband Forum. All rights reserved. Page 41 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

A CPE MUST support the use of HTTP redirection by the ACS. The CPE and ACS
requirements associated with the use of HTTP redirection are as follows:
 A CPE MUST support the 302 (Found) and 307 (Temporary Redirect) HTTP status
codes.
 A CPE MAY also support the 301 (Moved Permanently) HTTP status code for
redirection.
 The CPE MUST allow redirection to occur at any point during a Session (including
the InformResponse), and the ACS MAY issue a redirect at any point during a
Session.
 If the CPE is redirected, it MUST attempt to continue the Session using the URL
provided in the HTTP redirect response. Specifically, the CPE MUST re-send the
HTTP POST that resulted in the redirect response to the ACS at the redirected URL,
and the CPE MUST then attempt to proceed with the Session exactly as if no
redirection had occurred.
 If the CPE is redirected, the redirected URL MUST apply only to the remainder of the
current Session or until a subsequent redirect occurs later in the same Session. The
redirected URL MUST NOT be saved by the CPE (i.e. as the value of Management-
Server.URL, as defined in [24], [31] , and [32]) for use in any subsequent Session or
any subsequent retries of the Session. This requirement MUST hold even if the 301
(Moved Permanently) HTTP status code is used for redirection.
 The CPE MUST allow up to 5 consecutive redirections. If the CPE is redirected
more than 5 times consecutively, it MAY consider the Session unsuccessfully
terminated.
 The URL provided in HTTP redirection MAY be an HTTP or HTTPS URL. The
appropriate transport mechanism (TCP or TLS) MUST be used with the new target
regardless of the transport used before redirection.
 If TLS is used for the redirected Session, requiring the CPE to authenticate the ACS,
the authentication MUST be based on the redirected URL rather than the pre-
configured ACS URL (see Section 3.3).
 In an HTTP response sent by the ACS containing a redirect status code, the length of
the HTTP entity-body (Section 7.2/RFC 2616 [6]) MUST be zero. If the CPE
receives an HTTP re-direct response with a non-empty entity-body, it MUST ignore
the content of the entity-body.
 When redirected, the CPE MUST include all cookies associated with the Session in
subsequent HTTP requests to the redirected ACS. The CPE MUST consider a
redirect from an ACS to be a “verifiable transaction” as defined in [8], and thus it
MUST send cookies to the redirected ACS without performing domain validation of
each cookie.

November 2013 © The Broadband Forum. All rights reserved. Page 42 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

3.4.3 File Transfers

If the CPE is instructed to perform a file transfer via a Download, ScheduleDownload,
Upload, or ChangeDUState (Install or Update operations) request from the ACS, and if
the file location is specified as an HTTP URL with the same host name as the ACS, then
the CPE MUST choose one of the following approaches in performing the transfer:
 The CPE MAY send the HTTP GET/PUT over the already established
connection. Once the file has been transferred, the CPE MAY then proceed in
sending additional messages to the ACS while continuing to maintain the
connection (this option is not valid for ScheduleDownload or ChangeDUState
(Install or Update operations)).
 The CPE MAY open a second connection over which to transfer the file, while
maintaining the Session to the ACS over which it can continue to send messages.
 The CPE MAY terminate the Session to the ACS and then perform the transfer.
If the file location is not an HTTP URL or is not in the same domain as the ACS or
requires use of a different port, then only the latter two options are available to it.
A CPE MUST support the use of TLS as specified in Section 3.3 for establishment of a
separate TCP connection to transfer a file using HTTP. The CPE MUST use TLS when
the file location is specified as an HTTPS URL.
The CPE MUST support both HTTP basic and digest authentication for file transfers.
The specific authentication method is chosen by the file server by virtue of providing a
basic or digest authentication challenge. If authentication is used by the file server, the
ACS MUST specify credentials using the specific RPC method used to initiate the
transfer (i.e., Download, ScheduleDownload, Upload, ChangeDUState (Install or Update
operations)).

3.4.4 Authentication
If the CPE is not authenticated using TLS, the ACS MUST authenticate the CPE using
HTTP. If TLS is being used for encryption, the ACS SHOULD use basic authentication
[7]. If TLS is not being used, then the ACS MUST use digest authentication.
The CPE MUST support both HTTP basic and digest authentication. The ACS chooses
the authentication scheme by virtue of providing a basic or digest authentication
challenge. If TLS is being used for encryption, the CPE SHOULD preemptively send
basic authentication credentials as defined in Section 2 of [7].
Note – use of an authentication challenge requires the initial message (usually an Inform RPC
method request) to be sent; use of preemptive basic authentication with TLS is secure and avoids
the need for an additional request.
If the CPE has received an authentication challenge from the ACS (either basic or digest),
the CPE SHOULD send an Authorization header in all subsequent HTTP requests for the
duration of the TCP connection. Whether or not the CPE does this, the ACS MAY issue
subsequent authentication challenges at any stage of the Session within a single or
multiple TCP connections.

November 2013 © The Broadband Forum. All rights reserved. Page 43 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

If any form of HTTP authentication is used to authenticate the CPE, the CPE SHOULD
use a username/userid that is globally unique among all CPE manufacturers.
Specifically, the CPE username/userid SHOULD be in one of the following two formats:
<OUI> "-" <ProductClass> "-" <SerialNumber>
<OUI> "-" <SerialNumber>

If a username/userid of the above format is used, the <OUI>, <ProductClass>, and

<SerialNumber> fields MUST match exactly the corresponding Parameters included in
the DeviceIdStruct in the Inform message, as defined in Annex A, except that, in order to
guarantee that the Parameter values can be extracted from the username/userid, any
character in the <ProductClass> and <SerialNumber> that is not 0-9, A-Z, a-z, or an
underscore (“_”) MUST be escaped using URI percent-encoding, as defined in RFC 3986
[12].
Percent-encoding MUST be performed by converting each character to UTF-8 and then
percent-encoding each octet. For example, the character é (LATIN SMALL LETTER E
WITH ACUTE) is represented in UTF-8 as the two octets 0xC3 0xA9 and so would be
percent-encoded as “%C3%A9”.
Note – prior to the clarification that conversion to UTF-8 occurs before percent-encoding, the
escaped username/userid was ambiguous. For example, an implementation might have treated the
character é as the ISO Latin-1 octet 0xE9, which would have been percent-encoded as “%E9”.
If a username/userid of the above format is used, the second form MUST be used if and
only if the value of the ProductClass Parameter is empty.
Examples:
012345-0123456789
012345-STB-0123456789
012345-Set%2DTop%2DBox-0123456789

The password used in either form of HTTP authentication SHOULD be a unique value
for each CPE. That is, multiple CPE SHOULD NOT share the same password. This
password is a shared secret, and thus MUST be known by both CPE and ACS. The
method by which a shared secret becomes known to both entities on initial CPE
installation is outside the scope of this specification. Both CPE and ACS SHOULD take
appropriate steps to prevent unauthorized access to the password, or list of passwords in
the case of an ACS.

3.4.5 Digest Authentication

This Section outlines requirements for use of digest authentication within the CPE WAN
Management Protocol. These requirements apply to authentication of connections for
RPC exchanges as well as for file transfers. Note that ACS and CPE play the role of
HTTP client and server interchangeably for different types of connections. The ACS
plays the role of the HTTP client when making connection requests. The CPE plays the
role of the HTTP client when initiating connections to the ACS.
The CPE and the ACS MUST support the RFC 2617 “qop” option containing the value
“auth”. According to RFC 2617, this means that the HTTP client MUST use a new style
digest mechanism when this option is provided to it by the HTTP server.

November 2013 © The Broadband Forum. All rights reserved. Page 44 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

When using digest authentication, for each new TCP connection opened, the ACS
SHOULD use a new nonce value and the CPE SHOULD use a new cnonce value.
Note – if TLS is not used for a CPE WAN Management Protocol Session, the policy used by the
ACS for reusing nonce values for HTTP authentication can significantly affect the security of the
Session. In particular, if the ACS re-uses a nonce value when re-authenticating across multiple
TCP connections, the ACS can be vulnerable to replay attacks. However, if TLS is used for a
Session, then this risk is largely mitigated.
The CPE and the ACS MUST support the MD5 digest algorithm. The CPE MUST
additionally support the MD5-sess digest algorithm.

3.4.6 Additional HTTP Requirements

The following additional HTTP-related requirements are specified:
 Whenever the ACS sends an empty HTTP response, it MUST use the “204 (No
Content)” HTTP status code.
 The CPE MUST NOT make use of pipelining as defined in HTTP 1.1 [6].

3.4.7 HTTP Compression

This section outlines requirements for the use of HTTP compression using the HTTP
protocol to exchange content encodings as defined in section 3.5 Content Coding of RFC
2616 [6] within the CPE WAN Management Protocol. These requirements apply to
compression of RPC exchanges as well as for file transfers.
The following additional HTTP-related requirements are specified:
 The ACS SHOULD support the exchange of content encodings as defined in
section 3.5 Content Coding of RFC 2616 [6].
 The CPE SHOULD support the exchange of content encodings as defined in
section 3.5 Content Coding of RFC 2616 [6].
In order for the CPE and ACS to efficiently exchange compressed messages the CPE
MUST send the compressed message with the Content-Encoding header defined by the
ManagementServer.HTTPCompression Parameter, unless that Parameter is set to
“Disabled”.
If the ACS doesn’t support the Content-Encoding header or value, the ACS MUST
respond with the “415 – Unsupported Media Type” HTTP status code. Upon receipt of
the “415 – Unsupported Media Type” HTTP status code, the CPE MUST remove the
compression and retry the session as defined in section 3.2.1.1 Session Retry Policy.
The ACS can enable HTTP compression by setting the ManagementServer.HTTP-
Compression Parameter to a value supported by the CPE and ACS. The ACS can disable
HTTP compression by setting the ManagementServer.HTTPCompression Parameter to
“Disabled”. The CPE lists the supported HTTP compression mechanisms in the
ManagementServer.HTTPCompressionSupported Parameter.

November 2013 © The Broadband Forum. All rights reserved. Page 45 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

3.5 Use of SOAP

The CPE WAN Management Protocol defines SOAP 1.1 [9] as the encoding syntax to
transport the RPC method calls and responses defined in Annex A.
The following describes the mapping of RPC methods to SOAP encoding:
 The encoding MUST use the standard SOAP 1.1 envelope and serialization
namespaces:
 Envelope namespace identifier "http://schemas.xmlsoap.org/soap/envelope/"
 Serialization namespace identifier "http://schemas.xmlsoap.org/soap/encoding/"
 The data types used in Annex A correspond directly to the data types defined in the
SOAP 1.1 serialization namespace. (In general, the types used in Annex A are
restricted subsets of the corresponding SOAP types.)
 Following the SOAP specification [9], elements specified as being of type
“anySimpleType” MUST include a type attribute to indicate the actual type of the
element.
 Elements of a type other than “anySimpleType” MAY include a type attribute if and
only if the element is defined using a named data type in the RPC method XML
schema in Annex A. If a type attribute is included, the value of the type attribute
MUST exactly match the named data type specified in the schema.
 For an array argument, the argument name specified in the table in which the array is
defined MUST be used as the name of the overall array element. The name of the
member elements of an array MUST be the data type of the array as specified in the
table in which the array is defined (excluding the brackets and any length limitation
given in parentheses), and MUST NOT be namespace qualified. For example, an
argument named ParameterList, which is an array of ParameterValueStruct structures,
would be encoded as:
<ParameterList soap-enc:arrayType="cwmp:ParameterValueStruct[2]">
<ParameterValueStruct>
<name>Parameter1</name>
<value xsi:type="someType">1234</value>
</ParameterValueStruct>
<ParameterValueStruct>
<name>Parameter2</name>
<value xsi:type="someType">5678</value>
</ParameterValueStruct>
</ParameterList>

As a second example, the MethodList array in the GetRPCMethodsResponse would

be encoded as:
<MethodList soap-enc:arrayType="xsd:string[3]">
<string>GetRPCMethods</string>
<string>Inform</string>
<string>TransferComplete</string>
</MethodList>

Note – in the above examples, the XML namespace prefixes used are only examples. The actual
namespace prefix values are arbitrary, and are used only to refer to a namespace declaration.

November 2013 © The Broadband Forum. All rights reserved. Page 46 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Note – it is always necessary to specify an XML namespace prefix for the arrayType attribute.
For arrays of CWMP-specific types this will always be the CWMP namespace prefix, and for
arrays of other types it will always be the XML Schema namespace prefix or the SOAP encoding
namespace prefix.

 Regarding the SOAP specification for encoding RPC methods (Section 7 of [9]), for
each method defined in Annex A, each argument listed in the method call represents
an [in] parameter, while each argument listed in the method response represents an
[out] parameter. There are no [in/out] parameters used.
 The RPC methods defined use the standard SOAP naming convention whereby the
response message corresponding to a given method is named by adding the
“Response” suffix to the name of the method.
 A SOAP Envelope MUST contain exactly one Body element.
 A CPE MUST be able to accept a SOAP request with a total envelope size of at least
32 kilobytes (32768 bytes) without resulting in a “Resources Exceeded” response.
 A CPE MUST be able to generate a SOAP response of any required length without
resulting in a “Resources Exceeded” response, i.e. there is no maximum CPE SOAP
response length.
 An ACS MUST be able to accept a SOAP request with a total envelope size of at
least 32 kilobytes (32768 bytes) without resulting in a “Resources Exceeded”
response.
 An ACS MUST be able to generate a SOAP response of any required length without
resulting in a “Resources Exceeded” response, i.e. there is no maximum ACS SOAP
response length.
 A fault response MUST make use of the SOAP Fault element using the following
conventions:
 The SOAP faultcode element MUST indicate the source of the fault, either
“Client” or “Server”, as appropriate for the particular fault. In this usage, “Client”
represents the originator of the SOAP request, and “Server” represents the SOAP
responder. The value of the SOAP faultcode element MUST either be
unqualified or else be qualified with the SOAP envelope namespace prefix. The
recipient of the fault response need not make use of the value of this element, and
MAY ignore the SOAP faultcode element entirely.
 The SOAP faultstring sub-element MUST contain the string “CWMP
fault”.
 The SOAP detail element MUST contain a Fault structure. The RPC method
XML schema in Annex A formally defines this structure. This structure contains
the following elements:
o A FaultCode element that contains a single numeric fault code as defined
in Annex A.

November 2013 © The Broadband Forum. All rights reserved. Page 47 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

o A FaultString element that contains a human readable description of the

fault.
o A SetParameterValuesFault element, to be used only in an error
response to the SetParameterValues method, that contains a list of one or more
structures indicating the specific fault associated with each parameter in error.
This structure contains the following elements:
o A ParameterName element that contains the full Path Name of the
Parameter in error.
o A FaultCode element that contains a single numeric fault code as
defined in Annex A that indicates the fault associated with the particular
Parameter in error.
o A FaultString element that contains a human readable description of
the fault for the particular Parameter in error.

Below is an example envelope containing a fault response:

<soap:Envelope
xmlns:soap="http://schemas.xmlsoap.org/soap/envelope/"
xmlns:cwmp="urn:dslforum-org:cwmp-1-0">
<soap:Header>
<cwmp:ID soap:mustUnderstand="1">1234</cwmp:ID>
</soap:Header>
<soap:Body>
<soap:Fault>
<faultcode>Client</faultcode>
<faultstring>CWMP fault</faultstring>
<detail>
<cwmp:Fault>
<FaultCode>9000</FaultCode>
<FaultString>Upload method not supported</FaultString>
</cwmp:Fault>
</detail>
</soap:Fault>
</soap:Body>
</soap:Envelope>

Below is an example envelope containing a fault response for a SetParameterValues

method call:
<soap:Envelope
xmlns:soap="http://schemas.xmlsoap.org/soap/envelope/"
xmlns:cwmp="urn:dslforum-org:cwmp-1-0">
<soap:Header>
<cwmp:ID soap:mustUnderstand="1">1234</cwmp:ID>
</soap:Header>
<soap:Body>
<soap:Fault>
<faultcode>Client</faultcode>
<faultstring>CWMP fault</faultstring>
<detail>
<cwmp:Fault>
<FaultCode>9003</FaultCode>
<FaultString>Invalid arguments</FaultString>
<SetParameterValuesFault>
<ParameterName>
InternetGatewayDevice.Time.NTPServer1
</ParameterName>
<FaultCode>9007</FaultCode>

November 2013 © The Broadband Forum. All rights reserved. Page 48 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

<FaultString>Invalid IP Address</FaultString>
</SetParameterValuesFault>
<SetParameterValuesFault>
<ParameterName>
InternetGatewayDevice.Time.LocalTimeZoneName
</ParameterName>
<FaultCode>9007</FaultCode>
<FaultString>String too long</FaultString>
</SetParameterValuesFault>
</cwmp:Fault>
</detail>
</soap:Fault>
</soap:Body>
</soap:Envelope>

Note – in the above examples, the XML namespace prefixes used are only examples. The actual
namespace prefix values are arbitrary, and are used only to refer to a namespace declaration.
Note – in the above example, the CWMP namespace identifier “urn:dslforum-org:cwmp-1-0” is
only an example and is not necessarily the namespace that is defined by this specification.
A fault response MUST only be sent in response to a SOAP request. A fault response
MUST NOT be sent in response to a SOAP response or another fault response.
If a fault response does not follow all of the above requirements, the SOAP message
MUST be deemed invalid by the recipient. The consequences of invalid SOAP on the
CPE WAN Management Protocol Session are described in Section 3.7.
 When processing a received envelope, both ACS and CPE MAY ignore: (a) any
unknown XML elements within the SOAP Body6 and their sub elements or content,
(b) any unknown XML attributes and their values, (c) any embedded XML
comments, and (d) any XML processing instructions. Alternatively the ACS and
CPE MAY explicitly validate the received XML and reject an envelope that includes
unknown elements. Note that this precludes extending existing messages by
including additional arguments without changing the name of the message.
 If an RPC method requires references to XML Schema namespaces (for example for
the “type” attribute, or for references to XML Schema data types), these references
MUST be to the 2001 versions of these namespace definitions, specifically,
http://www.w3.org/2001/XMLSchema-instance and
http://www.w3.org/2001/XMLSchema. The recipient MAY reject an RPC method
that references a different version of either of these namespaces.
As an example of an RPC method encoded as described above, a GetParameterNames
request would be encoded as:
<soap-env:Envelope xmlns:soap-enc="http://schemas.xmlsoap.org/soap/encoding/"
xmlns:soap-env="http://schemas.xmlsoap.org/soap/envelope/"
xmlns:xsd="http://www.w3.org/2001/XMLSchema"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xmlns:cwmp="urn:dslforum-org:cwmp-1-0">
<soap-env:Header>
<cwmp:ID soap-env:mustUnderstand="1">0</cwmp:ID>
</soap-env:Header>
<soap-env:Body>
<cwmp:GetParameterNames>

6
With the exception that reception of a SOAP request to invoke an unsupported RPC method MUST result in a
SOAP-layer fault response with a fault code indicating “Method not Supported” (fault code 8000 or 9000).

November 2013 © The Broadband Forum. All rights reserved. Page 49 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

<ParameterPath>Object.</ParameterPath>
<NextLevel>0</NextLevel>
</cwmp:GetParameterNames>
</soap-env:Body>
</soap-env:Envelope>

Note – in the above example, the XML namespace prefixes used are only examples. The actual
namespace prefix values are arbitrary, and are used only to refer to a namespace declaration.
Note – the CWMP namespace prefix is specified only for elements that are defined at the top level
of the CWMP schema (ID and GetParameterNames in the above example). It is incorrect to
specify a namespace on elements contained within such elements (ParameterPath and NextLevel
in the above example). This is because the CWMP schema specifies an elementFormDefault value
of “unqualified”.
Note – in the above example, the CWMP namespace identifier “urn:dslforum-org:cwmp-1-0” is
only an example and is not necessarily the version that is defined by this specification.
The CPE WAN Management Protocol defines a series of SOAP Header elements as
specified in Table 4.
Table 4 – SOAP Header Elements
Tag Name Description
ID This header element MAY be used to associate SOAP requests and responses
using a unique identifier for each request, for which the corresponding response
contains the matching identifier. The value of the identifier is an arbitrary string and
is set at the discretion of the requester.
If used in a SOAP request, the ID header MUST appear in the matching response
(whether the response is a success or failure).
Because support for this header is required, the mustUnderstand attribute MUST be
set to “1” (true) for this header.
HoldRequests This header MAY be included in SOAP envelopes sent from an ACS to a CPE to
regulate transmission of requests from the CPE. This header MUST NOT appear in
envelopes sent from a CPE to an ACS.
This tag has Boolean values of “0” (false) or “1” (true). If the tag is not present, this
is interpreted as equivalent to a “0” (false).
The behavior of the CPE on reception of this header is defined in Section 3.7.1.3.
Support in the CPE for this header is REQUIRED.
Because support for this header is required, the mustUnderstand attribute MUST be
set to “1” (true) for this header.
This header is DEPRECATED because it unnecessarily complicates the protocol
and CWMP Session flow.
SessionTimeout This header MAY be included in SOAP envelopes sent from a CPE to an ACS
during CWMP Session initiation for the sole use of providing a suggestion of an
acceptable CWMP Session timeout duration. This header MUST NOT appear in
envelopes sent from an ACS to a CPE. This header also MUST NOT appear in
envelopes whose SOAP body does not include a CWMP Inform request.
The SessionTimeout is an integer that represents the number of seconds that
SHOULD be used by the ACS as the amount of time to wait before timing out a
CWMP Session due to the CPE not responding. The suggested SessionTimeout
MUST be 30 seconds or greater.
Because support for this header is OPTIONAL, the mustUnderstand attribute MUST
be set to “0” (false) for this header.

November 2013 © The Broadband Forum. All rights reserved. Page 50 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Tag Name Description

SupportedCWMPVersions This header MUST be included in SOAP envelopes sent from a CPE to an ACS
during CWMP Session initiation for the sole purpose of providing to the ACS a list of
supported CWMP versions. CPEs that support CWMP version 1.3 (or earlier) MUST
NOT send this header. This header MUST NOT appear in envelopes sent from an
ACS to a CPE. This header also MUST NOT appear in envelopes whose SOAP
body does not include a CWMP Inform request.
The SupportedCWMPVersions value is a comma-separated list of CWMP versions.
Existing versions at the time of publication are 1.0, 1.1, 1.2, 1.3, and 1.4.
Because support for this header is OPTIONAL, the mustUnderstand attribute MUST
be set to “0” (false) for this header.
UseCWMPVersion This header MUST be included in SOAP envelopes sent from an ACS to a CPE
during CWMP Session initiation for the sole purpose of providing the chosen CWMP
version to the CPE, if and only if the SupportedCWMPVersions header was included
on the Inform request and the ACS supports the SupportedCWMPVersions header.
This header MUST NOT appear in envelopes sent from a CPE to an ACS. This
header also MUST NOT appear in envelopes whose SOAP body does not include a
CWMP InformResponse.
The UseCWMPVersion value MUST be a single version, chosen from the list in
SupportedCWMPVersions that was sent with the Inform request.
Because this header is only sent when the CPE sends SupportedCWMPVersions,
the mustUnderstand attribute MUST be set to “1” (true) for this header.

Below is an example of two messages showing the use of some of the non-
DEPRECATED headers:
CPE to ACS SOAP header
<soap:Envelope
xmlns:soap="http://schemas.xmlsoap.org/soap/envelope/"
xmlns:cwmp="urn:dslforum-org:cwmp-1-2">
<soap:Header>
<cwmp:ID soap:mustUnderstand="1">1234</cwmp:ID>
<cwmp:SessionTimeout soap:mustUnderstand="0">40</cwmp:SessionTimeout>
</soap:Header>
<soap:Body>
<cwmp:Action>
<argument>value</argument>
</cwmp:Action>
</soap:Body>
</soap:Envelope>

ACS to CPE SOAP header

<soap:Envelope
xmlns:soap="http://schemas.xmlsoap.org/soap/envelope/"
xmlns:cwmp="urn:dslforum-org:cwmp-1-2">
<soap:Header>
<cwmp:ID soap:mustUnderstand="1">1234</cwmp:ID>
</soap:Header>
<soap:Body>
<cwmp:Action>
<argument>value</argument>
</cwmp:Action>
</soap:Body>
</soap:Envelope>

Note – in the above example, the XML namespace prefixes used are only examples. The actual
namespace prefix values are arbitrary, and are used only to refer to a namespace declaration.
Note – in the above example, the CWMP namespace identifier “urn:dslforum-org:cwmp-1-2” is
only an example and is not necessarily the version that is defined by this specification.

November 2013 © The Broadband Forum. All rights reserved. Page 51 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

3.6 RPC Support Requirements

Table 5 provides a summary of all methods, and indicates the conditions under which
implementation of each RPC method defined in Annex A is REQUIRED or OPTIONAL.
Table 5 – RPC message requirements
Method name CPE requirement ACS requirement
CPE methods Responding Calling
GetRPCMethods REQUIRED OPTIONAL
SetParameterValues REQUIRED REQUIRED
GetParameterValues REQUIRED REQUIRED
GetParameterNames REQUIRED REQUIRED
SetParameterAttributes REQUIRED OPTIONAL
GetParameterAttributes REQUIRED OPTIONAL
AddObject REQUIRED OPTIONAL
DeleteObject REQUIRED OPTIONAL
Reboot REQUIRED OPTIONAL
7
Download REQUIRED REQUIRED7
ScheduleDownload OPTIONAL OPTIONAL
Upload OPTIONAL OPTIONAL
FactoryReset OPTIONAL OPTIONAL
8
GetQueuedTransfers (DEPRECATED) OPTIONAL OPTIONAL
GetAllQueuedTransfers OPTIONAL OPTIONAL
CancelTransfer OPTIONAL OPTIONAL
ScheduleInform OPTIONAL OPTIONAL
ChangeDUState OPTIONAL OPTIONAL
SetVouchers (DEPRECATED) OPTIONAL9 OPTIONAL
9
GetOptions (DEPRECATED) OPTIONAL OPTIONAL
ACS methods Calling Responding
GetRPCMethods OPTIONAL REQUIRED
Inform REQUIRED REQUIRED
TransferComplete REQUIRED10 REQUIRED11
AutonomousTransferComplete OPTIONAL REQUIRED
12
DUStateChangeComplete OPTIONAL OPTIONAL13
AutonomousDUStateChangeComplete OPTIONAL OPTIONAL
RequestDownload OPTIONAL OPTIONAL
Kicked (DEPRECATED) OPTIONAL OPTIONAL14

7
REQUIRED only if file downloads of any type are supported.
8
DEPRECATED in favor of GetAllQueuedTransfers.
9
The voucher mechanism has been DEPRECATED in favor of the Software Module Management mechanism.
10
REQUIRED only if file downloads or uploads of any type are supported.
11
REQUIRED only if the ACS supports initiation of file downloads or uploads.
12
If the CPE responds to the ChangeDUState RPC then it MUST support this RPC.
13
If the ACS supports the ChangeDUState RPC then it MUST respond to this RPC.
14
DEPRECATED due to the deprecation of Annex D, which is the Section that defined the usage of this RPC.

November 2013 © The Broadband Forum. All rights reserved. Page 52 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

3.6.1 Alias-Based Addressing Mechanism Requirements

The OPTIONAL Alias-Based Addressing Mechanism makes use of the Instance Alias
identifiers defined in A.2.2.2 and described in Appendix II.
An ACS that supports the Alias-Based Addressing Mechanism MUST fully comply with
all the following requirements:
1. An ACS MUST NOT use Instance Alias identifiers with a CPE that has not
included the ManagementServer.AliasBasedAddressing Parameter (set to true) in
the Inform Parameters.
A CPE that supports the Alias-Based Addressing Mechanism MUST fully comply with
all the following requirements:
1. A CPE MUST support Instance Alias identifiers as alternative methods to address
Multi-Instance Objects in addition to Instance Number identifiers.
2. Upon creating an instance of a Multi-Instance Object, the CPE MUST assign a
unique Instance Alias (using a "cpe-" prefix) unless the Instance Alias value was
provided in CWMP RPC from the ACS. Aliases for instances created as a result
of any other action or contained in CPE factory defaults MUST be created with
the “cpe-“ prefix. The CPE MUST use the same Instance Alias values for factory
default objects across all instances of the CPE of the same hardware model and
software version.
3. The CPE MUST support the ManagementServer.AliasBasedAddressing
Parameter as a Forced Inform Parameter and include it (set to true) in all Inform
messages.
4. The CPE MUST support write access to the ManagementServer.AutoCreate-
Instances Parameter that is used by the ACS to enable or disable the CPE Auto-
Create Instance Mechanism (defined in A.3.2.1).
5. The CPE MUST support write access to the ManagementServer.InstanceMode
Parameter. This is used by the ACS to control whether the CPE will use Instance
Numbers or Instance Aliases in returned Path Names as detailed in requirements
6, 7, 8 and 9.
6. Upon receiving a request, the CPE MUST support uniform or mixed Instance
Identifiers for Objects in the Parameter Path Name. A mixed Parameter Path
Name has different Instance Identifier types (Instance Number or Instance Alias)
at the different node levels. When issuing a response, the CPE MUST match each
Object in the Parameter Path Name at each node level with the same Instance
Identifier type (Instance Number or Instance Alias) in the ACS request. All
permutations (in any order) present in the following table are valid and MUST be
supported:
Path Type Message Path Name Example
Uniform Instance Request TopGroup.Lev1Obj.1.Lev2Obj.1.
Number Identifier Response TopGroup.Lev1Obj.1.Lev2Obj.1.Parameter
Uniform Instance Request TopGroup.Lev1Obj.[a].Lev2Obj.[b].
Alias Identifier Response TopGroup.Lev1Obj.[a].Lev2Obj.[b].Parameter

November 2013 © The Broadband Forum. All rights reserved. Page 53 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Mixed Instance Request TopGroup.Lev1Obj.1.Lev2Obj.[b].

Identifier Response TopGroup.Lev1Obj.1.Lev2Obj.[b].Parameter

7. If the CPE has to issue a response that contains Object instances in the Parameter
Path Name with node levels below the Path Node that was received in the ACS
request, it MUST use the ManagementServer.InstanceMode Parameter to choose
how to provide the Path Name in the response:
o If the ManagementServer.InstanceMode Parameter is set to
InstanceNumber, all the Objects below the received Partial Path Name
MUST be returned using Instance Number identifiers only. All the
permutations (in any order) present in the following table are valid and
MUST be supported:
Path Type Message Path Name Example
Uniform Instance Request TopGroup.Lev1Obj.1.Lev2Obj.1.
Number identifier Response TopGroup.Lev1Obj.1.Lev2Obj.1.Lev3Obj.1.Parameter
Uniform Instance Request TopGroup.Lev1Obj.[a].Lev2Obj.[b].
Alias identifier Response TopGroup.Lev1Obj.[a].Lev2Obj.[b]. Lev3Obj.1.Parameter
Mixed Instance Request TopGroup.Lev1Obj.1.Lev2Obj.[b].
identifier Response TopGroup.Lev1Obj.1.Lev2Obj.[b]. Lev3Obj.1.Parameter

o If the ManagementServer.InstanceMode Parameter is set to InstanceAlias,

all the Objects located below the received Partial Path Name MUST
contain Instance Alias identifiers where such identifiers exist. All the
permutations (in any order) present in the following table are valid and
MUST be supported:
Path Type Message Path Name Example
Uniform Instance Request TopGroup.Lev1Obj.1.Lev2Obj.1.
Number identifier Response TopGroup.Lev1Obj.1.Lev2Obj.1.Lev3Obj.[c].Parameter
Uniform Instance Request TopGroup.Lev1Obj.[a].Lev2Obj.[b].
Alias identifier Response TopGroup.Lev1Obj.[a].Lev2Obj.[b].Lev3Obj.[c].Parameter
Mixed Instance Request TopGroup.Lev1Obj.1.Lev2Obj.[b].
identifier Response TopGroup.Lev1Obj.1.Lev2Obj.[b]. Lev3Obj.[c].Parameter

8. The ManagementServer.InstanceMode Parameter affects the ParameterList

argument of the CPE’s Inform RPC, by how the CPE returns Parameter Path
Names.
o If the ManagementServer.InstanceMode Parameter is set to
InstanceNumber, then all the Objects in Parameter Path Names MUST use
Instance Number identifiers only. For example:
Path Type Path Name Example
Uniform Instance
TopGroup.Lev1Obj.1.Lev2Obj.1.Parameter
Number identifier

November 2013 © The Broadband Forum. All rights reserved. Page 54 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

o If the ManagementServer.InstanceMode Parameter is set to InstanceAlias,

then all the Objects in Parameter Path Names MUST use Instance Alias
identifiers where such identifiers exist. For example:
Path Type Path Name Example
Uniform Instance
TopGroup.Lev1Obj.[a].Lev2Obj.[b].
Alias identifier

9. The ManagementServer.InstanceMode Parameter also affects how the CPE

returns the Parameter15 values that are Path Names or lists of Path Names.
o If the ManagementServer.InstanceMode Parameter is set to
InstanceNumber, then all the Parameter values that are Path Names or lists
of Path Names MUST be returned using Instance Number identifiers only.
For example:
Path Type Path Name Example
Uniform Instance
TopGroup.Lev1Obj.1.Lev2Obj.1.
Number identifier

o If the ManagementServer.InstanceMode Parameter is set to InstanceAlias,

then all the Parameter values that are Path Names or lists of Path Names
MUST be returned as follows:
 For the Parameter values that were not generated by the ACS via a
SetParameterValues or AddObject, using Instance Alias identifiers
where such identifiers exist. For example:
Path Type Path Name Example
Uniform Instance
TopGroup.Lev1Obj.[cpe-1].Lev2Obj.[cpe-2].
Alias identifier

 For the Parameter values that were generated by the ACS via a
SetParameterValues or AddObject, using the same Instance
Identifier types used when they were set. For example:
Path Type Action Parameter Value Path Name Example
Uniform Instance Set TopGroup.Lev1Obj.1.Lev2Obj.1
Number identifier Returned TopGroup.Lev1Obj.1.Lev2Obj.1
Uniform Instance Set TopGroup.Lev1Obj.[a].Lev2Obj.[b]
Alias identifier Returned TopGroup.Lev1Obj.[a].Lev2Obj.[b]
Mixed Instance Set TopGroup.Lev1Obj.1.Lev2Obj.[b]
identifier Returned TopGroup.Lev1Obj.1.Lev2Obj.[b]

15
This rule does not apply when the Parameter is a weak reference (Section 3.2.4/TR-106 [13]). In this case, the stored
value is always returned.

November 2013 © The Broadband Forum. All rights reserved. Page 55 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

10. The CPE MUST change its ManagementServer.InstanceMode Parameter to its

factory default value upon any event that requires the CPE to issue a
BOOTSTRAP event.

3.7 Session Procedures

All Sessions MUST begin with an Inform message from the CPE contained in the initial
HTTP POST. This serves to initiate the set of transactions and communicate the
limitations of the CPE with regard to message encoding. An Inform message MUST
NOT occur more than once during a Session (this limitation does not apply to the
potential need to retransmit an Inform request due to an HTTP “401 Unauthorized” status
code received as part of the HTTP authentication process, or due to an HTTP 3xx status
code received as part of an HTTP redirect).
The Session ceases when both the ACS and CPE have no more requests to send and no
responses remain due from either the ACS or the CPE. At such time, the CPE MUST
close the connection.
No more than one Session between a CWMP Endpoint and its associated ACS can exist
at a time.
Note – a Session is intended to persist only as long as there are messages to be transferred in
either direction. A Session and its associated TCP connection are not intended to be held open
after a specific exchange of information completes.

3.7.1 CPE Operation

3.7.1.1 Session Initiation
The CPE will initiate a Session to the ACS as a result of the conditions listed in Section
3.2.1. Once the connection to the ACS is successfully established, the CPE initiates a
Session by sending an initial Inform request to the ACS. This indicates to the ACS the
current status of the CPE and that the CPE is ready to accept requests from the ACS.
A CPE that supports CWMP version 1.4 (or later) will include in every Inform request (in
a SOAP SupportedCWMPVersions header) a comma-separated list of all of the CWMP
version numbers that it supports.
 If a CMWP version 1.4 (or newer) CPE receives a UseCWMPVersion header in the
InformResponse containing a version that the CPE sent in the
SupportedCWMPVersions header, then the CPE MUST use the CWMP version
returned in UseCWMPVersion.
 If a CWMP version 1.4 (or newer) CPE receives a UseCWMPVersion header in the
InformResponse containing a version that the CPE did not send in the
SupportedCWMPVersions header, then the CPE MUST abort session initiation by
closing the TCP connection.
 If a CPE supporting any CWMP version does not receive a UseCWMPVersion, the
CPE MUST infer the CWMP version from the CWMP namespace in the
InformResponse returned from the ACS. Table 6 gives the mapping between CWMP
namespace and CWMP version for the CPE.

November 2013 © The Broadband Forum. All rights reserved. Page 56 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Table 6 – Inferring ACS CWMP Version 1.0-1.3 from CWMP Namespace

CWMP Namespace CWMP Version
urn:dslforum-org:cwmp-1-0 1.0
urn:dslforum-org:cwmp-1-1 1.1
urn:dslforum-org:cwmp-1-2 1.2 (there is no way for the CPE to infer 1.3)

For the remainder of the CWMP session, the CPE MUST NOT use any feature that is
incompatible with the CWMP version chosen by the CPE.
The CPE MUST consider the Session to have been successfully initiated if and only if it
receives a successful InformResponse.
From the time a Session is initiated until the Session is terminated, the CPE MUST
ensure the transactional integrity of all Parameters accessible via the CPE WAN
Management Protocol. During the course of a Session, all configurable Parameters of the
CPE MUST appear to the ACS as a consistent set modified only by the ACS.
Throughout the Session the CPE MUST shield the ACS from seeing any updates to the
Parameters performed by other entities. This includes the values of configurable
Parameters as well as presence or absence of configurable Parameters and Objects. The
means by which the CPE achieves this transactional integrity is a local matter.
The CPE MUST take any necessary steps to ensure transactional integrity of the Session.
For example, it might be necessary, in exceptional cases, for the CPE to terminate a
LAN-side management session in order to meet CWMP Session establishment
requirements.
3.7.1.2 Incoming Requests
While in a Session (after the Session was successfully initiated, but before the Session
termination criteria described in 3.7.1.4 have been met), on reception of a SOAP request
from the ACS, the CPE MUST respond to that request in the next HTTP POST that it
sends to the ACS.
3.7.1.3 Outgoing Requests
While in a Session (after the Session was successfully initiated, but before the Session
termination criteria described in 3.7.1.4 have been met), if the CPE has one or more
requests to send to the ACS, the CPE MUST send one of these requests in the next HTTP
POST if and only if all of the following conditions are met:
 The most recently received HTTP response from the ACS did not contain a SOAP
request.
 The ACS has indicated that HoldRequests is false (see Section 3.4.7). This condition
is met if and only if the most recently received HTTP response from the ACS
contained one of the following:
o A SOAP envelope with the HoldRequests header set to a value of false.
o A SOAP envelope with no HoldRequests header.
o No SOAP envelope (an empty HTTP response).
Note – the HoldRequests SOAP Header element is DEPRECATED (see Section 3.4.7), so the ACS
is not expected to send it. However, the ACS might send it, so the CPE still needs to support it.

November 2013 © The Broadband Forum. All rights reserved. Page 57 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

 At any prior time during the current Session, the CPE has not sent an empty HTTP
POST at a time that the ACS had indicated that HoldRequests is false (as described
above).
If the CPE has more than one request pending when the above criteria are met, the choice
of which request to send is at the discretion of the CPE unless otherwise specified.
While in a Session, if any of the above conditions are not met or if the CPE has no
requests to send to the ACS, and if the most recent HTTP response from the ACS did not
contain a SOAP request, the CPE MUST send an empty HTTP POST.
Once the CPE has sent an empty HTTP POST when the most recent HoldRequests was
false (see Section 3.4.7), the CPE MUST NOT send any further requests for the
remainder of the Session. In this case, if the CPE has additional requests to send to the
ACS, the CPE MUST wait until a subsequent Session to send these requests.
Table 7 summarizes what the CPE MUST send to the ACS as long as the Session is in
progress (after the Session was successfully initiated, but before the Session termination
criteria described in 3.7.1.4 have been met).
Table 7 – CPE Message Transmission Constraints
HoldRequests ACS request outstanding No ACS request outstanding
CPE requests pending16 false Response Request
true Response Empty HTTP POST
No CPE requests pending - Response Empty HTTP POST

3.7.1.4 Session Termination

The CPE MUST terminate the Session when all of the following conditions are met:
1) The ACS has no further requests to send the CPE. The CPE concludes this if and
only if the most recent HTTP response from the ACS was empty.
2) The CPE has no further requests to send to the ACS and the CPE has issued an
empty HTTP POST to the ACS while HoldRequests is false (which indicates to
the ACS that the CPE has no further requests for the remainder of the Session).
As defined in Table 7, if this condition has not been met but the CPE has no
further requests or responses, it MUST send an empty HTTP POST, which will
then fulfill this condition.
Note – the HoldRequests SOAP Header element is DEPRECATED (see Section 3.4.7), so the
ACS is not expected to send it. However, the ACS might send it, so the CPE still needs to
support it.
3) The CPE has received all outstanding response messages from the ACS.
4) The CPE has sent all outstanding response messages to the ACS resulting from
prior requests.

16
The CPE can have requests pending only if the CPE has not already sent an empty HTTP POST when the most
recent HoldRequests was false. Otherwise, the CPE is considered to have no requests pending.

November 2013 © The Broadband Forum. All rights reserved. Page 58 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

The CPE MUST also consider a Session unsuccessfully terminated if it has received no
HTTP response from an ACS for a locally determined time period of not less than 30
seconds. If the CPE fails to receive an HTTP response, the CPE MUST NOT attempt to
retransmit the corresponding HTTP request as part of the same Session.
If the CPE receives a SOAP-layer fault in response to an Inform request with a fault code
other than “Retry request” (fault code 8005), the CPE MUST consider the Session to
have terminated unsuccessfully.
If the CPE receives an HTTP response from the ACS for which the XML is not well-
formed, for which the SOAP structure is deemed invalid, that contains a SOAP fault that
is not in the form specified in Section 3.4.7, or for which the CPE deems that the protocol
has been violated, the CPE MUST consider the Session to have terminated
unsuccessfully.
If the CPE receives an HTTP response from the ACS with a fault status code (a 4xx or
5xx status code) that is not otherwise handled by the CPE, the CPE MUST consider the
Session to have terminated unsuccessfully. Note that while the CPE would accept an
HTTP response with a “401 Unauthorized” status code as part of the normal
authentication process, when the CPE subsequently attempts to authenticate, if the
resulting HTTP response contains a “401 Unauthorized” status code, the CPE MUST
consider the Session to have terminated unsuccessfully.
If the above conditions are not met, the CPE MUST continue the Session.
If the CPE receives a SOAP-layer fault response as defined in Section 3.4.7 with a fault
code other than “Retry request” (fault code 8005) in response to any method other than
Inform, the CPE MUST continue with the remainder of the Session. That is, a fault
response of this type MUST NOT cause the Session to unsuccessfully terminate.
Note – in a fault condition, it is entirely at the discretion of the ACS whether its fault response is a
SOAP-layer fault, which would cause the Session to continue, or an HTTP-layer fault, which
would cause the Session to terminate unsuccessfully.
If one or more messages exchanged during a Session results in the CPE needing to reboot
to complete the requested operation, the CPE MUST wait until after the Session has
cleanly terminated based on the above criteria before performing the reboot.
If the Session terminates unexpectedly, the CPE MUST retry the Session as specified in
Section 3.2.1.1. The CPE MAY place locally specified limits on the number of times it
attempts to reestablish a Session in this case.
3.7.1.5 Events
An event is an indication that something of interest has happened that requires the CPE to
notify the ACS via an Inform request defined in Section A.3.3.1. The CPE MUST
attempt to deliver every event at least once. If the CPE is not currently in a Session with
the ACS, it MUST attempt to deliver events immediately; otherwise, it MUST attempt to
deliver them after the current Session terminates. The CPE MUST receive confirmation
from the ACS for it to consider an event successfully delivered. Once the CPE has
delivered an event successfully, the CPE MUST NOT send the same event again. On the
other hand, the ACS MUST be prepared to receive the same event more than once
because the ACS might have sent a response the CPE never receives. Many types of

November 2013 © The Broadband Forum. All rights reserved. Page 59 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

events (e.g., PERIODIC, VALUE CHANGE) can legally appear in subsequent Sessions
even when successfully delivered in the earlier Session. In such cases, an event in the
later Session indicates the reoccurrence of an event of the same type rather than an
attempt to retry an event delivery failure.
For every type of event there is a policy that dictates if and when the CPE MUST retry
event delivery if a previous delivery attempt failed. When event delivery is retried it
MUST be in the immediately following Session; events whose delivery fails in one
Session cannot be omitted in the following Session and then later redelivered.
For most events, delivery is confirmed when the CPE receives a successful
InformResponse. Six standard event types (KICKED17, TRANSFER COMPLETE,
AUTONOMOUS TRANSFER COMPLETE, REQUEST DOWNLOAD, DU STATE
CHANGE COMPLETE, and AUTONOMOUS DU STATE CHANGE COMPLETE)
indicate that one or more methods (Kicked [Section A.4.2.1], TransferComplete [Section
A.3.3.2], AutonomousTransferComplete [Section A.3.3.3], RequestDownload [Section
A.4.2.2], DUStateChangeComplete [Section A.4.2.3], AutonomousDUStateChange-
Complete [Section A.4.2.4] respectively) will be called later in the Session, and it is the
successful response to these methods that indicates event delivery. The CPE MAY also
send vendor-specific events (using the syntax specified in Table 8), in which case
successful delivery, retry, and discard policy is subject to vendor definition.
If no new events occur while the CPE has some events to redeliver, the CPE MUST
attempt to redeliver them according to the schedule defined by the session retry policy in
Section 3.2.1.1.
Below is a table of event types, their codes in an Inform request, their cumulative
behavior, the responses the CPE MUST receive to consider them successfully delivered,
and the policy for retrying and/or discarding them if delivery is unsuccessful.

17
DEPRECATED due to the deprecation of Annex D, which is the Section that defined the usage of this Event.

November 2013 © The Broadband Forum. All rights reserved. Page 60 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Table 8 – Event Types

Event Code Cumulative Explanation ACS Response for Retry/Discard
Behavior Successful Delivery Policy
"0 BOOTSTRAP" Single Indicates that the Session was InformResponse The CPE MUST NOT
established due to first-time ever discard an
CPE installation or a change to undelivered
the ACS URL. BOOTSTRAP event.
The specific conditions that All other undelivered
MUST result in the events MUST be
BOOTSTRAP EventCode are: discarded on
 First time connection of the BOOTSTRAP.
CWMP Endpoint to the
ACS from the factory.
 First time connection of the
CWMP Endpoint to the
ACS after a factory reset.
 First time connection of the
CWMP Endpoint to the
ACS after the ACS URL
has been modified in any
way.
Note that as with all other
EventCode values, the
BOOTSTRAP EventCode MAY
be included in the Event array
along with other EventCode
values. It would be expected,
for example, that on the initial
boot of the CPE from the
factory, the CPE would include
both the BOOTSTRAP and
BOOT EventCodes.
"1 BOOT" Single Indicates that the Session was InformResponse The CPE MUST retry
established due to the CPE delivery until it
being powered up or reset. reboots before
This includes initial system discarding it.
boot, as well as reboot due to
any cause, including use of the
Reboot method, but not waking
up from standby.
"2 PERIODIC" Single Indicates that the Session was InformResponse The CPE MUST NOT
established on a periodic ever discard an
Inform interval. undelivered
PERIODIC event
(except on
BOOTSTRAP).
"3 SCHEDULED" Single Indicates that the Session was InformResponse The CPE MUST NOT
established due to a ever discard an
ScheduleInform method call. undelivered
This event code MUST only be SCHEDULED event
used with the “M (except on
ScheduleInform” event code BOOTSTRAP).
(see “M ScheduleInform”,
below).

November 2013 © The Broadband Forum. All rights reserved. Page 61 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Event Code Cumulative Explanation ACS Response for Retry/Discard

Behavior Successful Delivery Policy
"4 VALUE Single Indicates that since the last InformResponse The CPE MUST retry
CHANGE" successful Inform (under the delivery until it
conditions defined in Section reboots. It MUST
A.3.2.4), the value of one or discard the event on
more Parameters with Passive BOOTSTRAP.
or Active notification enabled
(including Parameters defined
to require Forced Active
Notification) has been modified
(even if its value has changed
back to the value it had at the
time of the last successful
Inform).
If this EventCode is included in
the Event array, all such
modified Parameters MUST be
included in the ParameterList in
this Inform. If this event is ever
discarded then the list of
modified Parameters MUST be
discarded at the same time.
"5 KICKED"18 Single Indicates that the Session was KickedResponse The CPE MAY retry
(DEPRECATED) established for the purpose of delivery at its
web identity management (see discretion.
Annex D) and that a Kicked
method (see Section A.4.2.1)
will be called one or more times
during this Session.
“6 CONNECTION Single Indicates that the Session was InformResponse The CPE MUST NOT
REQUEST” established due to a retry delivery.
Connection Request from the
ACS as described in Section
3.2.
“7 TRANSFER Single Indicates that the Session was TransferCompleteResponse The CPE MUST NOT
COMPLETE” established to indicate the ever discard an
completion of a previously undelivered
requested download or upload TRANSFER
(either successful or COMPLETE event
unsuccessful) and that the (except on
TransferComplete method will BOOTSTRAP).
be called one or more times
during this Session.
This event code MUST only be
used with the “M Download”,
“M ScheduleDownload” and/or
“M Upload” event codes (see
“M Download”, “M
ScheduleDownload” and “M
Upload”, below).
"8 DIAGNOSTICS Single Used when reestablishing a InformResponse The CPE MUST retry
COMPLETE" connection to the ACS after delivery until it
completing one or more reboots before
diagnostic test initiated by the discarding it.
ACS.
“9 REQUEST Single Indicates that the Session was RequestDownloadResponse The CPE MAY retry
DOWNLOAD” established for the CPE to call delivery at its
the RequestDownload method discretion.
(see Section A.4.2.2) one or
more times.

18
DEPRECATED due to the deprecation of Annex D, which is the Section that defined the usage of this Event.

November 2013 © The Broadband Forum. All rights reserved. Page 62 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Event Code Cumulative Explanation ACS Response for Retry/Discard

Behavior Successful Delivery Policy
“10 AUTONOMOUS Single Indicates that the Session was AutonomousTransfer- The CPE MUST NOT
TRANSFER established to indicate the CompleteResponse ever discard an
COMPLETE” completion of a download or undelivered
upload that was not specifically AUTONOMOUS
requested by the ACS (either TRANSFER
successful or unsuccessful) COMPLETE event
and that the Autonomous- (except on
TransferComplete method will BOOTSTRAP).
be called one or more times
during this Session.
“11 DU STATE Single Indicates that the Session was DUStateChangeComplete- The CPE MUST NOT
CHANGE established to indicate the Response ever discard an
COMPLETE” completion of a previously undelivered DU
requested DU state change, STATE CHANGE
either successful or COMPLETE event
unsuccessful, and that the (except on
DUStateChangeComplete BOOTSTRAP).
method will be called during
this Session.

This method MUST only be

used with the “M
ChangeDUState” event code
(see “M ChangeDUState”,
below).
“12 AUTONOMOUS Single Indicates that the Session was AutonomousDUState- The CPE MUST NOT
DU STATE established to indicate the ChangeCompleteResponse ever discard an
CHANGE completion of a DU state undelivered
COMPLETE” change not specifically AUTONOMOUS DU
requested by a STATE CHANGE
ChangeDUState RPC (either COMPLETE event
successful or unsuccessful) (except on
and that the Autonomous- BOOTSTRAP).
DUStateChangeComplete
method will be called during
this Session.
“13 WAKEUP” Single Indicates that the Session was InformResponse The CPE MUST retry
established due to the CPE delivery until it
waking up from standby under reboots. It MUST
the conditions specified in L.2. discard the event on
A device that implements the BOOTSTRAP.
WAKEUP event code MUST
implement the StandbyPolicy:1
profile as defined in tr-157-1-
8.xml [38]
“M Reboot” Multiple The CPE rebooted upon InformResponse The CPE MUST NOT
request from the ACS through ever discard an
the use of the Reboot RPC. undelivered “M
Overlaps with one of the Reboot” event
causes that can generate a “1 (except on
BOOT” event code. BOOTSTRAP).
“M ScheduleInform” Multiple The ACS requested a InformResponse The CPE MUST NOT
scheduled Inform. ever discard an
undelivered “M
ScheduleInform”
event (except on
BOOTSTRAP).
“M Download” Multiple A content download previously TransferCompleteResponse The CPE MUST NOT
requested by the ACS using ever discard an
the Download method (see undelivered “M
Section A.3.2.8) has finished. Download” event
Overlaps with “7 TRANSFER (except on
COMPLETE”. BOOTSTRAP).

November 2013 © The Broadband Forum. All rights reserved. Page 63 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Event Code Cumulative Explanation ACS Response for Retry/Discard

Behavior Successful Delivery Policy
“M Multiple A content download previously TransferCompleteResponse The CPE MUST NOT
ScheduleDownload” requested by the ACS using ever discard an
the ScheduleDownload method undelivered “M
(see Section A.4.1.8) has ScheduleDownload”
finished. Overlaps with “7 event (except on
TRANSFER COMPLETE”. BOOTSTRAP).
“M Upload” Multiple A content upload previously TransferCompleteResponse The CPE MUST NOT
requested by the ACS using ever discard an
the Upload method (see undelivered “M
Section A.4.1.5) has finished. Upload” event
Overlaps with “7 TRANSFER (except on
COMPLETE”. BOOTSTRAP).
“M ChangeDUState” Multiple A DU state change previously DUStateChangeComplete- The CPE MUST NOT
requested by the ACS using Response ever discard an
the ChangeDUState method undelivered “M
(see Section A.4.1.10) has ChangeDUState”
finished. Overlaps with “11 DU event (except on
STATE CHANGE BOOTSTRAP).
COMPLETE”.
"M " <vendor- Not The action requested by a Not specified Not specified
specific method> specified vendor-specific method is
complete. The action taken by
the CPE and response by the
ACS is vendor-specific. A
vendor-specific method name
MUST be in the form specified
in Section A.3.1.1.
For example:
“M X_012345_MyMethod”
“X “<VENDOR> ” ” Not Vendor-specific event. The Not specified Not specified
<event> specified VENDOR after the “X“ and
space is a unique vendor
identifier, which MAY be either
an OUI or a domain name. The
OUI or domain name used for a
given vendor-specific event
MUST be one that is assigned
to the organization that defined
this method (which is not
necessarily the same as the
vendor of the CPE or ACS). An
OUI is an organizationally
unique identifier as defined in
[10], which MUST be formatted
as a 6 hexadecimal-digit OUI
(organizationally unique
identifier), with all upper-case
letters and any leading zeros
included. A domain name
MUST be upper case with each
dot (“.”) replaced with a hyphen
or underscore.
For example:
“X 012345 MyEvent”
“X ACME_COM MyEvent”

The Cumulative Behavior column of the above table distinguishes between event types
that are not cumulative (“Single”) and those that are cumulative (“Multiple”). For
example, if the CPE reboots while the previous “1 BOOT” event has not yet been
delivered, it makes no sense for the next Inform to contain two “1 BOOT” Event array
entries. In contrast, if a download completes while the previous “M Download” event

November 2013 © The Broadband Forum. All rights reserved. Page 64 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

has not yet been delivered, the next Inform would contain two “M Download” Event
array entries because each relates to a different ACS request. The “Single” and
“Multiple” cumulative behaviors are defined as follows:
 If an event with “Single” cumulative behavior occurs, the list of events in the next
Inform MUST contain only one instance of this EventCode, regardless of whether
there are any undelivered events of the same type.
 If an event with “Multiple” cumulative behavior occurs, the new EventCode MUST
be included in the list of events, independent of any undelivered events of the same
type, and this MUST NOT affect any such undelivered events.
When one or more events are directly related to the same root cause, then all such events
MUST be included in the Event array. Below are examples of such cases (this list is not
exhaustive):
 Reboot caused by the Reboot RPC method. In this case the Inform MUST include at
least the following EventCode values:
"1 BOOT"
"M Reboot"
 TransferComplete sent in a new Session due to a prior Download request, where there
is no reboot associated with the completion of the transfer:
"7 TRANSFER COMPLETE"
"M Download"
 One or more Parameter values for which Passive notification has been set have
changed since the most recent Inform, and a periodic Inform occurs (in this case, the
events MUST be included in the same Inform because for Passive notifications, the
Inform in which the “4 VALUE CHANGE” event would occur would have to result
from some other cause—in this example, a periodic inform):
"2 PERIODIC"
"4 VALUE CHANGE"
For events that are due to unrelated causes, if they occur simultaneously, the CPE
SHOULD include all such events in the same Inform message, but MAY send separate
Inform messages for each such event. An example of unrelated events is:
"2 PERIODIC"
"7 TRANSFER COMPLETE"
3.7.1.6 Method Retry Behavior
If in response to a request from the CPE the CPE receives a “Retry request” response
(fault code 8005) from the ACS, the CPE MUST resend the identical request in the next
HTTP POST within the current Session. This behavior applies to all ACS methods
(including Inform).
If instead the CPE receives a fault response with any fault code other than 8005 in
response to any method other than Inform, the CPE MUST proceed with the Session, and

November 2013 © The Broadband Forum. All rights reserved. Page 65 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

MUST NOT attempt to retry the method (such a response in the case of Inform will
terminate the Session, as described in Section 3.7.1.4).

3.7.2 ACS Operation

3.7.2.1 Session Initiation
Upon receiving the initial Inform request from the CPE, if the ACS wishes to allow the
initiation of the Session, it MUST respond with an InformResponse.
An ACS that supports CWMP version 1.4 (or later) MUST understand the Supported-
CWMPVersions header.
 If a CWMP version 1.4 (or newer) ACS receives the SupportedCWMPVersions
SOAP header, the ACS MUST choose the appropriate version for this CWMP session
from the list of versions in the SupportedCWMPVersions header, and return that
version to the CPE in a SOAP UseCWMPVersion header in the InformResponse.
 If a CWMP version 1.4 (or newer) ACS receives the SupportedCWMPVersions
SOAP header, and the ACS does not support any of the versions in the list of versions
in the SupportedCWMPVersions header, the ACS MUST abort session initiation by
returning an 8006 SOAP-layer fault.
 If a CWMP version 1.4 (or newer) ACS does not receive the
SupportedCWMPVersions SOAP header, then the ACS MUST infer the CWMP
version (which will be between 1.0 and 1.3 inclusive) from the CWMP namespace in
the SOAP envelope of the Inform request. Table 9 gives the mapping between
CWMP namespace and CWMP version for the ACS. In this case, the ACS MUST
NOT send the UseCWMPVersion SOAP header in the InformResponse.
 If a CWMP version 1.3 (or older) ACS receives the SupportedCWMPVersions SOAP
header, the ACS will most likely ignore the SOAP header (since it does not
understand it and mustUnderstand is set to “false”). The ACS will most likely infer
the CWMP version (which will be between 1.0 and 1.3 inclusive) from the CWMP
namespace in the SOAP envelope of the Inform request. Table 9 gives the mapping
between CWMP namespace and CWMP version for the ACS. In this case, the ACS
will not send the UseCWMPVersion SOAP header in the InformResponse.

Table 9 – Inferring CPE CWMP Version 1.0-1.3 from CWMP Namespace

CWMP Namespace CWMP Version
urn:dslforum-org:cwmp-1-0 1.0
urn:dslforum-org:cwmp-1-1 1.1
urn:dslforum-org:cwmp-1-2 1.2 if the SOAP SessionTimeout header is absent, otherwise 1.3

For the rest of the CWMP session, the ACS MUST NOT use any feature that is
incompatible with the CWMP version chosen by the ACS.
Note – an ACS that supports only v1.0 of the CPE WAN Management Protocol will expect the
initial Inform request from the CPE to use the v1.0 namespace identifier “urn:dslforum-
org:cwmp-1-0”, and to contain only event types that were defined in v1.0 of the protocol. The
behavior of such an ACS when it receives an initial Inform from a CPE that supports v1.1 (or
later) is not possible to predict. The ACS might fail to notice that the CPE supports a later

November 2013 © The Broadband Forum. All rights reserved. Page 66 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

version, in which case it will respond with an InformResponse; it might return a SOAP-layer fault;
or it might return an HTTP-layer fault. If it returns a fault, the CPE will need to decide whether
or not to revert to v1.0 of the protocol when retrying the failed Session.
The ACS MUST ignore any event types that it does not recognize.
3.7.2.2 Incoming Requests
While in a Session (after the Session was successfully initiated, but before the Session
termination criteria described in 3.7.2.4 have been met), on reception of a SOAP request
from the CPE, the ACS MUST respond to that request in the next HTTP response sent to
the CPE.
Note – the HoldRequests SOAP Header element is DEPRECATED (see Section 3.4.7), so the
ACS SHOULD NOT send it.

3.7.2.3 Outgoing Requests

While in a Session (after the Session was successfully initiated, but before the Session
termination criteria described in 3.7.2.4 have been met), if the ACS has one or more
requests to send to the CPE and the most recent HTTP POST from the CPE did not
contain a SOAP request, the ACS MUST send one of these requests in the next HTTP
response.
Otherwise, while in a Session, if the ACS has no requests to send to the CPE and the
most recent HTTP POST from the CPE did not contain a SOAP request, the ACS MUST
send an empty HTTP response.
Table 10 summarizes what the ACS MUST send to the CPE as long as the Session is in
progress (after the Session was successfully initiated, but before the Session termination
criteria described in 3.7.2.4 have been met).
Table 10 – ACS Message Transmission Constraints
CPE request outstanding No CPE request outstanding
ACS requests pending Response Request
No ACS requests pending Response Empty HTTP response

3.7.2.4 Session Termination

Since the CPE is driving the HTTP connection to the ACS, only the CPE is responsible
for connection initiation and teardown.
The ACS MUST consider the Session terminated when all of the following conditions are
met:
1) The CPE has no further requests to send the ACS. The ACS concludes this if and
only if it has received an empty HTTP POST from the CPE while HoldRequests
is false.
Note – the HoldRequests SOAP Header element is DEPRECATED (see Section 3.4.7), so the
ACS SHOULD NOT send it.
2) The ACS has no further requests to send the CPE and the most recent HTTP
response the ACS sent to the CPE was empty (which indicates to the CPE that the
ACS has no further requests).

November 2013 © The Broadband Forum. All rights reserved. Page 67 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

3) The ACS has sent all outstanding response messages to the CPE resulting from
prior requests.
4) The ACS has received all outstanding response messages from the CPE.
If all of the above criteria have been met before the ACS has sent its final HTTP
response, the final HTTP response from the ACS MUST be empty.
If the above criteria have not all been met, but the ACS has not received an HTTP POST
from a given CPE within a locally defined timeout of not less than 30 seconds, it MAY
consider the Session terminated. In this case, the ACS MAY attempt to reestablish a
Session by performing a Connection Request (see Section 3.2.2).
If the ACS receives an HTTP POST from the CPE for which the XML is not well-
formed, for which the SOAP structure is deemed invalid, or that contains a SOAP fault
that is not in the form specified in Section 3.4.7, the ACS MUST respond to the CPE with
an HTTP 400 status code (Bad Request), and MUST consider the Session to have
terminated unsuccessfully. This fault response MUST NOT contain any SOAP content,
but MAY contain human-readable text that further explains the nature of the fault.
If the ACS receives a request associated with a Session that it considers expired, or if the
ACS determines that some other protocol violation has occurred, or for other reasons at
the discretion of the ACS19, the ACS MAY cause a Session to terminate unsuccessfully
by responding to the CPE with an HTTP 400 status code (Bad Request). This HTTP
response MUST NOT contain any SOAP content, but MAY contain human readable-text
that further explains the nature of the fault.
If the ACS receives a SOAP fault response from the CPE, as defined in Section 3.4.7, the
ACS MUST interpret any unrecognized fault code between 9000 and 9799 (inclusive) the
same as 9001 (Request denied), and MAY choose among the following actions:
 The ACS MAY force the unsuccessful termination of the Session. To do this, the
ACS MUST respond to the CPE with an HTTP 400 status code (Bad Request). This
HTTP response MUST NOT contain any SOAP content, but MAY contain human
readable-text that further explains the nature of the fault. This will result in the CPE
retrying the Session.
 The ACS MAY attempt to terminate the Session successfully, in which case the CPE
will not attempt to retry the Session. To do this, the ACS would send no more
requests to the CPE, and would follow the rules defined above to determine when the
Session terminates.
 The ACS MAY continue with the Session, sending additional requests to the CPE.

19
With the exception that reception of a SOAP request to invoke an unsupported RPC method MUST result in a
SOAP-layer fault response with a fault code indicating “Method not supported” (fault code 8000).

November 2013 © The Broadband Forum. All rights reserved. Page 68 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

3.7.3 Transaction Examples

In the example shown in Figure 3, the ACS first reads a set of Parameter values, and
based on the result, sets some Parameter values.
Figure 3 – Session Example

CPE ACS
Open connection

SSL initiation

HTTP post
Inform request

HTTP response
Inform response

HTTP post (empty)

HTTP response
GetParameterValues request

HTTP post
GetParameterValues response

HTTP response
SetParameterValues request

HTTP post
SetParameterValues response

HTTP response (empty)

Close connection

November 2013 © The Broadband Forum. All rights reserved. Page 69 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

3.7.4 CWMP Version Negotiation

The following table illustrates the CWMP versions that will be negotiated in all possible
cases.

Table 11 – CWMP Version Negotiation

1.0 CPE 1.1-1.3 CPE 1.4 (or later) CPE
1.0 ACS 1. CPE sends 1.0 namespace 1. CPE sends 1.1-1.3 1. CPE sends
2. ACS sends a 1.0 namespace SupportedCWMPVersions
namespace response that 2. ACS sends a fault or a 1.0 header element
does not contain namespace response 2. ACS ignores
UseCWMPVersion header 3. CPE chooses CWMP SupportedCWMPVersion
element version 1.0 header element
3. CPE chooses CWMP ACS chooses CWMP 3. ACS sends a fault or a v1.0
version 1.0 version 1.0 namespace response
ACS chooses CWMP 4. CPE chooses CWMP version
version 1.0 1.0
ACS chooses CWMP version
1.0
1.1-1.3 ACS 1. CPE sends 1.0 namespace 1. CPE sends 1.1-1.3 1. CPE sends
2. ACS sends a 1.0 namespace SupportedCWMPVersions
namespace response that 2. ACS does not send header element
does not contain UseCWMPVersion header 2. ACS ignores
UseCWMPVersion header element SupportedCWMPVersions
element 3. CPE chooses min(CPE header element
3. CPE chooses CWMP CWMP version, ACS CWMP 3. ACS does not send
version 1.0 version) UseCWMPVersion header
ACS chooses CWMP ACS chooses min(CPE element
version 1.0 CWMP version, ACS CWMP 4. CPE chooses ACS CWMP
version) version
ACS chooses ACS CWMP
version
1.4 (or 1. CPE sends 1.0 namespace 1. CPE sends 1.1-1.3 1. CPE sends
later) ACS 2. ACS sends a 1.0 namespace SupportedCWMPVersions
namespace response that 2. ACS does not send header element
does not contain UseCWMPVersion header 2. ACS uses unspecified logic to
UseCWMPVersion header element determine CWMP version
element 3. CPE chooses CPE CWMP from the supplied list
3. CPE chooses CWMP version 3. ACS replies with
version 1.0 ACS chooses ACS CWMP UseCWMPVersion header
ACS chooses CWMP version element
version 1.0 4. CPE chooses CWMP version
specified by
UseCWMPVersion
ACS chooses CWMP version
specified by
UseCWMPVersion

November 2013 © The Broadband Forum. All rights reserved. Page 70 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Normative References
The following documents are referenced by this specification. Where the protocol
defined in this specification depends on a referenced document, support for all required
components of the referenced document is implied unless otherwise specified.
The following references are associated with document conventions or context for this
specification, but are not associated with requirements of the CPE WAN Management
Protocol itself.
[1] RFC 2119, Key words for use in RFCs to Indicate Requirement Levels,
http://www.ietf.org/rfc/rfc2119.txt
[2] TR-046, Auto-Configuration Architecture & Framework, Broadband Forum
Technical Report
[3] TR-062, Auto-Configuration for the Connection Between the DSL Broadband
Network Termination (B-NT) and the Network using ATM, Broadband Forum
Technical Report
[4] TR-044, Auto-Configuration for Basic Internet (IP-based) Services, Broadband
Forum Technical Report

The following references are associated with required components of the CPE WAN
Management Protocol.
[5] RFC 1034, Domain names – concepts and facilities,
http://www.ietf.org/rfc/rfc1034.txt
[6] RFC 2616, Hypertext Transfer Protocol -- HTTP/1.1,
http://www.ietf.org/rfc/rfc2616.txt
[7] RFC 2617, HTTP Authentication: Basic and Digest Access Authentication,
http://www.ietf.org/rfc/rfc2617.txt
[8] RFC 6265, HTTP State Management Mechanism, http://www.ietf.org/rfc/rfc6265.txt
[9] Simple Object Access Protocol (SOAP) 1.1, http://www.w3.org/TR/2000/NOTE-
SOAP-20000508
[10] Organizationally Unique Identifiers (OUIs), http://standards.ieee.org/faqs/OUI.html
[11] RFC 5246, The Transport Layer Security (TLS) Protocol, Version 1.2,
http://www.ietf.org/rfc/rfc5246.txt
[12] RFC 3986, Uniform Resource Identifier (URI): Generic Syntax,
http://www.ietf.org/rfc/rfc3986.txt
[13] TR-106, Data Model Template for TR-069-Enabled Devices, Broadband Forum
Technical Report

The following references are associated with optional or recommended components of

the CPE WAN Management Protocol.

November 2013 © The Broadband Forum. All rights reserved. Page 71 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

[14] RFC 2132, DHCP Options and BOOTP Vendor Extensions,

http://www.ietf.org/rfc/rfc2132.txt
[15] XML-Signature Syntax and Processing, http://www.w3.org/2000/09/xmldsig
[16] PKCS #7, Cryptographic Message Syntax Standard,
http://www.rsasecurity.com/rsalabs/pkcs/pkcs-7/index.html or
http://www.ietf.org/rfc/rfc2315.txt
[17] Port Numbers, http://www.iana.org/assignments/port-numbers
[18] IANA Private Enterprise Numbers registry,
http://www.iana.org/assignments/enterprise-numbers
[19] RFC 2104, HMAC: Keyed-Hashing for Message Authentication,
http://www.ietf.org/rfc/rfc2104.txt
[20] RFC 2131, Dynamic Host Configuration Protocol,
http://www.ietf.org/rfc/rfc2131.txt
[21] RFC 3489, STUN - Simple Traversal of User Datagram Protocol (UDP) Through
Network Address Translators (NATs), http://www.ietf.org/rfc/rfc3489.txt
[22] RFC 3925, Vendor-Identifying Vendor Options for Dynamic Host Configuration
Protocol version 4 (DHCPv4), http://www.ietf.org/rfc/rfc3925.txt
[23] HTML 4.01 Specification, http://www.w3.org/TR/html4
[24] TR-098, Internet Gateway Device Data Model for TR-069, Broadband Forum
Technical Report
[25] TR-104, Provisioning Parameters for VoIP CPE, Broadband Forum Technical
Report
[26] TR-135, Data Model for a TR-069 Enabled STB, Broadband Forum Technical
Report
[27] TR-140 Issue 1.1, TR-069 Data Model for Storage Service Enabled Devices,
Broadband Forum Technical Report
[28] TR-143, Enabling Network Throughput Performance Tests and Statistical
Monitoring, Broadband Forum Technical Report
[29] TR-157, Component Objects for CWMP, Broadband Forum Technical Report
[30] TR-196, Femto Access Point Service Data Model, Broadband Forum Technical
Report
[31] TR-181 Issue 1, Device Data Model for TR-069, Broadband Forum Technical
Report
[32] TR-181 Issue 2, Device Data Model for TR-069, Broadband Forum Technical
Report
[33] RFC 5389, Session Traversal Utilities for NAT (STUN),
http://www.ietf.org/rfc/rfc5389.txt

November 2013 © The Broadband Forum. All rights reserved. Page 72 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

[34] RFC 4122, A Universally Unique IDentifier (UUID) URN Namespace,

http://www.ietf.org/rfc/rfc4122.txt
[35] RFC 3315, Dynamic Host Configuration Protocol for IPv6 (DHCPv6),
http://www.ietf.org/rfc/rfc3315.txt
[36] IEEE 802a, IEEE Standard for Local and Metropolitan Area Networks: Overview
and Architecture - Amendment 1: Ethertypes for Prototype and Vendor-Specific
Protocol Development.
[37] RFC 6120, Extensible Messaging and Presence Protocol (XMPP): Core,
http://www.ietf.org/rfc/rfc6120.txt
[38] tr-157-1-8.xml, Component Objects for CWMP, Broadband Forum,
http://www.broadband-forum.org/cwmp/tr-157-1-8.xml
[39] UPnP IGD v1, UPnP InternetGatewayDevice:1 Device Template, UPnP Forum,
http://upnp.org/specs/gw/UPnP-gw-InternetGatewayDevice-v1-Device.pdf
[40] UPnP IGD v2, UPnP InternetGatewayDevice:2 Device Template, UPnP Forum,
http://upnp.org/specs/gw/UPnP-gw-InternetGatewayDevice-v2-Device.pdf
[41] UPnP WAN PPP v1, UPnP WANPPPConnection:1 Service, UPnP Forum,
http://upnp.org/specs/gw/UPnP-gw-WANPPPConnection-v1-Service.pdf
[42] UPnP WAN IP v2, UPnP WANIPConnection:2 Service, UPnP Forum,
http://upnp.org/specs/gw/UPnP-gw-WANIPConnection-v2-Service.pdf
[43] UPnP WAN IPv6 FW v1, UPnP WANIPv6FirewallControl:1 Service, UPnP
Forum, http://upnp.org/specs/gw/UPnP-gw-WANIPv6FirewallControl-v1-
Service.pdf
[44] RFC 6092, Recommended Simple Security Capabilities in Customer Premise
Equipment (CPE) for Providing Residential IPv6 Internet Services,
http://www.ietf.org/rfc/rfc6092.txt
[45] TR-124 Issue 3, Functional Requirements for Broadband Residential Gateway
Devices, Broadband Forum Technical Report

November 2013 © The Broadband Forum. All rights reserved. Page 73 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Annex A. RPC Methods

A.1 Introduction
In the CPE WAN Management Protocol, a remote procedure call mechanism is used for
bi-directional communication between a CPE device and an Auto-configuration Server
(ACS). This Annex specifies the specific procedure calls (methods). This includes both
methods initiated by an ACS and sent to a CPE, as well as methods initiated by a CPE
and sent to an ACS.
This specification is intended to be independent of the syntax used to encode the defined
RPC methods. The particular encoding syntax to be used in the context of the CPE WAN
Management Protocol is defined in Section 3.4.7.

A.2 RPC Method Usage

A.2.1 Data Types
The RPC methods defined in this specification make use of a limited subset of the default
SOAP data types [9]. The complete set of types utilized in this specification along with
the notation used to represent these types is listed in Table 12.
Table 12 – Data types
Type Description
string For strings listed in this specification, a maximum allowed length can be listed using the form string(N),
where N is the maximum string length in characters.
For all strings a maximum length is either explicitly indicated or implied by the size of the elements
composing the string. For strings in which the content is an enumeration, the longest enumerated
value determines the maximum length. If a string does not have an explicitly indicated maximum
length or is not an enumeration, the default maximum is 16 characters. Action arguments containing
strings longer than the specified maximum MAY result in an “Invalid arguments” error response.
int Integer in the range –2147483648 to +2147483647, inclusive.
For some int types listed, a value range is given using the form int[Min:Max], where the Min and Max
values are inclusive. If either Min or Max are missing, this indicates no limit.
unsignedInt Unsigned integer in the range 0 to 4294967295, inclusive.
For some unsignedInt types listed, a value range is given using the form unsignedInt[Min:Max], where
the Min and Max values are inclusive. If either Min or Max are missing, this indicates no limit.
boolean Boolean, where the allowed values are “0”, “1”, “true”, and “false”. The values “1” and “true” are
considered interchangeable, where both equivalently represent the logical value true. Similarly, the
values “0” and “false” are considered interchangeable, where both equivalently represent the logical
value false.

November 2013 © The Broadband Forum. All rights reserved. Page 74 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Type Description
dateTime The subset of the ISO 8601 date-time format defined by the SOAP dateTime type.
All times MUST be expressed in UTC (Universal Coordinated Time) unless explicitly stated otherwise
in the definition of a variable of this type.
If absolute time is not available to the CPE, it SHOULD instead indicate the relative time since boot,
where the boot time is assumed to be the beginning of the first day of January of year 1, or
0001-01-01T00:00:00. For example, 2 days, 3 hours, 4 minutes and 5 seconds since boot would be
expressed as 0001-01-03T03:04:05. Relative time since boot MUST be expressed using an
untimezoned representation. Any untimezoned value with a year value less than 1000 MUST be
interpreted as a relative time since boot.
If the time is unknown or not applicable, the following value representing “Unknown Time” MUST be
used: 0001-01-01T00:00:00Z.
Any dateTime value other than one expressing relative time since boot (as described above) MUST
use UTC timezoned representation (that is, it MUST include a timezone suffix of “Z”, “-00:00”, or
“+00:00”).
base64 Base64 encoded binary.
A maximum allowed length can be listed using the form base64(N), where N is the maximum length in
characters before Base64 encoding.
anySimpleType The value of an element defined to be of type “anySimpleType” MAY be of any simple data type,
including (but not limited to) any of the other types listed in this table.
Following the SOAP specification [9], elements specified as being of type “anySimpleType” MUST
include a type attribute to indicate the actual type of the element. For example:
<ParameterValueStruct>
<Name>InternetGatewayDevice.ProvisioningCode</Name>
<Value xsi:type="xsd:string">code12345</Value>
</ParameterValueStruct>
The namespaces xsi and xsd used above are as defined in [9].

The methods used in this specification also make use of structures and arrays (in some
cases containing mixed types). Array elements are indicated with square brackets after
the data type. If specified, the maximum length of the array is indicated within the
brackets. If the maximum length is not specified, unless otherwise indicated, there is no
fixed requirement on the number of elements the recipient will be able to accommodate.
A request with an array too large for the recipient to accommodate SHOULD result in the
“Resources exceeded” fault code. Unless otherwise specified, the order of items in an
array MUST NOT have any effect on the interpretation of the contents of the array.

A.2.2 Instance Identifiers

In some cases, where multiple instances of an Object can occur, the placeholder node
name “{i}” is shown. In actual use, this placeholder is to be replaced by an Instance
Identifier.
An Instance Identifier is a value that uniquely identifies an instance within a Multi-
Instance Object.
An Instance Identifier lifespan is the same as that of its addressed Object instance.
Two types of Instance Identifiers are available: Instance Number and Instance Alias.

A.2.2.1 Instance Number Identifier

The Instance Number identifier allows a Parameter or sub-object within an Object to be
referenced by using this Instance Number in the Path Name. The Instance Number
assigned by the CPE is arbitrary.

November 2013 © The Broadband Forum. All rights reserved. Page 75 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Note – the fact that Instance Numbers are arbitrary means that they do not define a useful Object
ordering, e.g. the ACS cannot assume that a newly-created Object will have a higher Instance
Number than its existing sibling Objects.
The CPE SHOULD NOT assign an Instance Number that has been used for a previously
deleted Object instance. The CPE SHOULD exhaust the full space of integer values for a
given Object before re-using Instance Numbers.
Once an Object instance is created, the assigned Instance Numbers MUST persist
unchanged until the Object is subsequently deleted (either by the ACS or by a third
party). This implies that the Instance Number MUST persist across reboots of the CPE,
and that the CPE MUST NOT allow the Instance Number of an existing Object instance
to be modified by a third-party entity.
The Instance Number identifier MUST be supported by the CPE.
An Instance Number is expressed as a positive integer (>=1), for example:
Device.Services.ABCService.1

A.2.2.2 Instance Alias Identifier

This is the Instance Identifier used by the OPTIONAL Alias-Based Addressing
Mechanism (see Section 3.6.1). When the Alias-Based Addressing Mechanism is
supported, the Path Names within RPC arguments MAY contain Instance Aliases.
An Instance Alias is expressed as a string surrounded in square brackets, for example:
Device.Services.ABCService.[a]
The square brackets are the notation used to distinguish an Instance Alias from an
Instance Number.
The string contained between the square brackets is the value of the addressed Object
instance’s Alias Parameter (described in Section 3.8/TR-106 [13]). The Instance Alias
MUST always be unique within its parent Object and MUST never be empty.
An Instance Alias can be read via its addressed Object instance’s Alias Parameter.
An Instance Alias can be changed by modifying its addressed Object instance’s Alias
Parameter.

A.2.3 Other Requirements

Any message that is sent or received whose arguments do not adhere to the normative
CWMP XSD as defined in A.6 MUST generate an error response.
Future versions of this specification MUST NOT alter the RPC method signatures
defined in this Annex. Any changes needed in a future version MUST result only in new
RPC methods with distinct names being defined.

November 2013 © The Broadband Forum. All rights reserved. Page 76 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

A.3 Baseline RPC Messages

A.3.1 Generic Methods
The methods listed in this Section are REQUIRED to be supported on both CPE devices
and ACSs. Either a CPE or ACS MAY call these methods.

A.3.1.1 GetRPCMethods
This method MAY be used by a CPE or ACS to discover the set of methods supported by
the ACS or CPE it is in communication with. This list MUST include all the supported
methods, both standard methods (those defined in this specification or a subsequent
version) and vendor-specific methods. The receiver of the response MUST ignore any
unrecognized methods.
Vendor-specific methods MUST be in the form X_<VENDOR>_MethodName, where
<VENDOR> is a unique vendor identifier, which MAY be either an OUI or a domain
name. The OUI or domain name used for a given vendor-specific method MUST be one
that is assigned to the organization that defined this method (which is not necessarily the
same as the vendor of the CPE or ACS). An OUI is an organizationally unique identifier
as defined in [10], which MUST formatted as a 6 hexadecimal-digit OUI
(organizationally unique identifier), with all upper-case letters and any leading zeros
included. A domain name MUST be upper case with each dot (“.”) replaced with a
hyphen or underscore. Examples: X_012345_MyMethod, X_ACME_COM_MyMethod.
The calling arguments for this method are defined in Table 13. The arguments in the
response are defined in Table 14.
Table 13 – GetRPCMethods arguments
Argument Type Description
- void This method has no calling arguments.

November 2013 © The Broadband Forum. All rights reserved. Page 77 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Table 14 – GetRPCMethodsResponse arguments

Argument Type Description
MethodList string(64)[] Array of strings containing the names of each of the RPC methods the recipient supports.
The list of methods returned by an ACS MUST always include “Inform”.
For example, a CPE implementing only the baseline methods defined in this version of
the specification would return the following list when requested by an ACS:
"GetRPCMethods"
"SetParameterValues"
"GetParameterValues"
"GetParameterNames"
“SetParameterAttributes”
“GetParameterAttributes”
“AddObject”
“DeleteObject”
“Reboot”
“Download”
As another example, an ACS implementing only the baseline methods defined in this
version of the specification would return the following list when requested by a CPE:
“Inform”
"GetRPCMethods"
“TransferComplete”

The following fault codes are defined for this method for response from a CPE: 9001,
9002.
The following fault codes are defined for this method for response from an ACS: 8001,
8002, 8005.

A.3.2 CPE Methods

The methods listed in this Section are defined to be supported on a CPE device. Only an
ACS can call these methods.

A.3.2.1 SetParameterValues
This method MAY be used by an ACS to modify the value of one or more CPE
Parameters.
The calling arguments for this method are defined in Table 15. The arguments in the
response are defined in Table 16.
Table 15 – SetParameterValues arguments
Argument Type Description
ParameterList ParameterValueStruct[] Array of name-value pairs as specified in Table 17. For each name-
value pair, the CPE is instructed to set the Parameter specified by the
name to the corresponding value.
This array MUST NOT contain more than one entry with the same
Parameter name. If a given Parameter appears in this array more than
once, the CPE MUST respond with fault 9003 (Invalid arguments).
If the length of this array is zero, then the CPE MUST set the
ParameterKey to the value specified by the ParameterKey argument,
but MUST NOT set any other Parameter values.

November 2013 © The Broadband Forum. All rights reserved. Page 78 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Argument Type Description

ParameterKey string(32) The value to set the ParameterKey Parameter. The CPE MUST set
ParameterKey to the value specified in this argument if and only if
SetParameterValues completes successfully. If SetParameterValues
does not complete successfully (implying that the Parameter value
changes requested did not take effect), the value of ParameterKey
MUST NOT be modified. ParameterKey provides the ACS a reliable
and extensible means to track changes made by the ACS. The value of
this argument is left to the discretion of the ACS, and MAY be left
empty.

Table 16 – SetParameterValuesResponse arguments

Argument Type Description
Status int[0:1] A successful response to this method returns an integer enumeration defined as follows:
0 = All Parameter changes have been validated and applied.
1 = All Parameter changes have been validated and committed, but some or all are not yet
applied (for example, if a reboot is required before the new values are applied).

If the CPE supports the OPTIONAL Alias-Based Addressing Mechanism (as defined in
Section 3.6.1 and described in Appendix II) and its ManagementServer.AutoCreate-
Instances Parameter value is set to true, then the Auto-Create Instance Mechanism is
performed by the CPE as follows:
 For each Instance Alias identifier supplied in the Path Name that does not already
exist, the CPE MUST follow the rules in Section A.3.2.6 for automatically
creating the new Object instances.
Note: The CPE assigned Instance Number is not returned with the
SetParameterValuesResponse.
On successful receipt of a SetParameterValues RPC, the CPE MUST apply the changes
to all of the specified Parameters atomically. That is, either all of the value changes are
applied together, or none of the changes are applied at all. In the latter case, the CPE
MUST return a fault response indicating the reason for the failure to apply the changes.
The CPE MUST NOT apply any of the specified changes without applying all of them.
This requirement MUST hold even if the CPE experiences a crash during the process of
applying the changes. The order of Parameters listed in the ParameterList has no
significance20 21, meaning that the application of value changes to the CPE MUST be
independent of the order in which they are listed.
If the request is valid, it is strongly RECOMMENDED that the CPE apply the requested
changes prior to sending the SetParameterValues response. If it does so, the CPE MUST

20
Modification of ManagementServer.AutoCreateInstances or ManagementServer.InstanceMode Parameter(s) will
have an undefined effect on Parameters within the same RPC command that are affected by the Auto-Create
Instance Mechanism. This is a result of the order of the Parameters processed in the RPC by the CPE having no
significance.
21
For a CPE that supports the Alias-Based Addressing Mechanism, the fact that the order of the Parameters in the
ParameterList has no significance means that the effect is undefined when a SetParameterValues RPC is used to
change the value of an Alias Parameter that is also within the same RPC, used in a Parameter name or Parameter
value that is a Path Name or a list of Path Names.

November 2013 © The Broadband Forum. All rights reserved. Page 79 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

set the value of Status in the response to 0 (zero), indicating that the changes have been
applied.
If the CPE requires the Session to be terminated before applying some or all of the
Parameter values, the CPE MUST reply before all Parameter values have been applied,
and thus MUST set the value of Status in the response to 122. In this case, the reply
MUST come only after all validation of the request has been completed and the new
values have been appropriately saved such that they will definitely be applied as soon as
physically possible after the Session has terminated. Once the CPE issues the
SetParameterValues response, all changes associated with the corresponding request
(including the new ParameterKey) MUST be available for subsequent commands to
operate on, regardless of whether the changes have been applied or not. In particular, the
use of GetParameterValues to read a Parameter modified by an earlier
SetParameterValues MUST return the modified value, even if that value has not yet been
applied.
If the value of Status in the SetParameterValues response is 1, the requested changes
MUST be applied as soon as physically possible after the Session has terminated, and no
later than the beginning of the next Session. Note that if a CPE requires a reboot to cause
the changes to be applied, the CPE MUST initiate that reboot on its own after the
termination of the Session. Because some CPE will not require a reboot in these
circumstances, an ACS SHOULD NOT call the Reboot method as a result of modifying
the CPE’s configuration, since this would result in an unnecessary reboot. Note also that
if application of a configuration change by the CPE would result in a service disruption
(for example, if the CPE requires a reboot to apply the requested change), it is not the
responsibility of the CPE to avoid or delay such a disruption. To minimize the impact of
such a disruption, the ACS MAY delay requesting such a configuration change until an
appropriate time, but this is entirely at the ACS’s discretion.
The use of the Status value is independent between successive SetParameterValues,
AddObject, or DeleteObject requests within the same Session. The use of a Status value
of 1 in response to one request does not necessarily imply that subsequent requests in the
same Session will also respond in the same way.
The ACS MAY set Parameter values in any combination or order of its choosing using
one or multiple SetParameterValues RPCs.
All modifications to a CPE’s configuration resulting from use of the SetParameterValues
method MUST be retained across reboots of the CPE.
The ParameterValueStruct structure is defined in Table 17.
Table 17 – ParameterValueStruct definition
Name Type Description
Name string(256) This is the name of a Parameter. The CPE MUST treat
the Parameter name as case sensitive.

22
When modifying ManagementServer.AutoCreateInstances or ManagementServer.InstanceMode and the CPE returns
a committed response (status = 1), all subsequent commands affected by the Alias-Based Addressing Mechanism
within the same Session will not reflect the updated mode change(s).

November 2013 © The Broadband Forum. All rights reserved. Page 80 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Name Type Description

Value anySimpleType This is the value the Parameter is to be set. The CPE
MUST treat string-valued Parameter values as case-
sensitive.

The following fault codes are defined for this method: 9001, 9002, 9003, 9004, 9005,
9006, 9007 and 9008.
For any Path Name node in the SetParameterValues RPC that is referred to by an
Instance Number that does not exist, the CPE MUST return a fault response with Invalid
Parameter Name (9005) fault code.
When the OPTIONAL Alias-Based Addressing Mechanism is enabled and its
ManagementServer.AutoCreateInstances Parameter value is set to false, then the CPE
MUST return a fault response with Invalid Parameter Name (9005) fault code for any
Path Name node in the SetParameterValues RPC that is referred to by an Instance Alias
that does not exist.
If there is a fault due to one or more Parameters in error, the primary fault code indicated
for the overall fault response MUST be Invalid Arguments (9003). The fault response for
this method MUST include a SetParameterValuesFault element for each Parameter in
error.
The CPE MUST reject an attempt to set values using the SetParameterValues RPC that
would result in an invalid configuration, where an invalid configuration is defined as one
of the following:
 A Parameter value or combination of Parameter values that are explicitly prohibited
in the definition of the Data Model(s) supported by the CPE.
 A Parameter value or combination of Parameter values that are not supported by the
CPE.
In both of the above cases, the response from the CPE MUST include a
SetParameterValuesFault element for each such Parameter, indicating the Invalid
Parameter Value fault code (9007).
The CPE MUST NOT impose any additional configuration restrictions beyond the
exceptions described above and restrictions otherwise explicitly permitted or required by
the CPE WAN Management Protocol.

A.3.2.2 GetParameterValues
This method MAY be used by an ACS to obtain the value of one or more CPE
Parameters. The calling arguments for this method are defined in Table 18. The
arguments in the response are defined in Table 19.

November 2013 © The Broadband Forum. All rights reserved. Page 81 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Table 18 – GetParameterValues arguments

Argument Type Description
ParameterNames string(256)[] Array of strings, each representing the name of a requested Parameter.
If a Parameter name argument is given as a Partial Path Name, the request is to
be interpreted as a request to return all of the Parameters in the branch of the
naming hierarchy that shares the same prefix as the argument. A Partial Path
Name MUST end with a “.” (dot) after the last node name in the hierarchy. An
empty string indicates the top of the name hierarchy.
Below is an example of a full Parameter name:
InternetGatewayDevice.DeviceInfo.SerialNumber
Below is an example of a Partial Path Name:
InternetGatewayDevice.DeviceInfo.

Table 19 – GetParameterValuesResponse arguments

Argument Type Description
ParameterList ParameterValueStruct[] Array of name-value pairs, as specified in Table 17, containing the
name and value for each requested Parameter.
If multiple entries in the ParameterNames array in the
GetParameterValues request overlap such that there are multiple
requests for the same Parameter value, it is at the discretion of the CPE
whether or not to duplicate that Parameter in the response array. That
is, the CPE MAY either include that Parameter value only once in its
response, or it MAY include that Parameter value once for each
instance that it was requested.
If the ParameterNames argument in the request was a Partial Path
Name, and if there are no Parameters within the Object represented by
that Partial Path Name (at any level below), the ParameterList MUST be
empty, and this MUST NOT cause an error response.

The following fault codes are defined for this method: 9001, 9002, 9003, 9004, 9005.
If the fault is caused by one or more invalid Parameter names in the ParameterNames
array, the Invalid Parameter Name fault code (9005) MUST be used instead of the more
general Invalid Arguments fault code (9003). The value of a ParameterNames element
MUST be considered invalid if it does not exactly match either the name of a Parameter
currently present in the CPE’s Data Model (if the ParameterNames element does not end
with a dot) or the name of an Object currently present in the CPE’s Data Model (if
ParameterNames element ends with a dot).

A.3.2.3 GetParameterNames
This method MAY be used by an ACS to discover the Parameters accessible on a
particular CPE. The calling arguments for this method are defined in Table 20. The
arguments in the response are defined in Table 21.
Table 20 – GetParameterNames arguments
Argument Type Description
ParameterPath string(256) A string containing either a complete Parameter name, or a Partial Path Name
representing a subset of the name hierarchy. An empty string indicates the top of
the name hierarchy. A Partial Path Name MUST end with a “.” (dot) after the last
node name in the hierarchy.
Below is an example of a full Parameter name:
InternetGatewayDevice.DeviceInfo.SerialNumber
Below is an example of a Partial Path Name:
InternetGatewayDevice.DeviceInfo.

November 2013 © The Broadband Forum. All rights reserved. Page 82 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Argument Type Description

NextLevel boolean If false, the response MUST contain the Parameter or Object whose name exactly
matches the ParameterPath argument, plus all Parameters and Objects that are
descendents of the Object given by the ParameterPath argument, if any (all levels
below the specified Object in the Object hierarchy). For example, if ParameterPath
were “InternetGatewayDevice.LANDevice.1.Hosts.”, the response would include the
following (if there were a single instance of Host with Instance Number “1”):
InternetGatewayDevice.LANDevice.1.Hosts.
InternetGatewayDevice.LANDevice.1.Hosts.HostNumberOfEntries
InternetGatewayDevice.LANDevice.1.Hosts.Host.
InternetGatewayDevice.LANDevice.1.Hosts.Host.1.
InternetGatewayDevice.LANDevice.1.Hosts.Host.1.IPAddress
InternetGatewayDevice.LANDevice.1.Hosts.Host.1.AddressSource
InternetGatewayDevice.LANDevice.1.Hosts.Host.1.LeaseTimeRemaining
InternetGatewayDevice.LANDevice.1.Hosts.Host.1.MACAddress
InternetGatewayDevice.LANDevice.1.Hosts.Host.1.HostName
InternetGatewayDevice.LANDevice.1.Hosts.Host.1.InterfaceType
InternetGatewayDevice.LANDevice.1.Hosts.Host.1.Active
If true, the response MUST contain all Parameters and Objects that are next-level
children of the Object given by the ParameterPath argument, if any. For example, if
ParameterPath were “InternetGatewayDevice.LANDevice.1.Hosts.”, the response
would include the following:
InternetGatewayDevice.LANDevice.1.Hosts.HostNumberOfEntries
InternetGatewayDevice.LANDevice.1.Hosts.Host.
Or, if ParameterPath were empty, with NextLevel equal true, the response would list
only “InternetGatewayDevice.” (if the CPE is an Internet Gateway Device).

Table 21 – GetParameterNamesResponse arguments

Argument Type Description
ParameterList ParameterInfoStruct[] Array of structures, each containing the name and other information for a
Parameter or Object, as defined in Table 22.
When NextLevel is false, this list MUST contain the Parameter or Object
whose name exactly matches the ParameterPath argument, plus all
Parameters and Objects that are descendents of the Object given by the
ParameterPath argument, if any (all levels below the specified Object in
the Object hierarchy). If the ParameterPath argument is an empty
string, names of all Objects and Parameters accessible on the particular
CPE are returned.
When NextLevel is true, this list MUST contain all Parameters and Object
that are next-level children of the Object given by the ParameterPath
argument, if any.
For a Parameter, the Name returned in this structure MUST be a full Path
Name, ending with the name of the Parameter element. For an Object,
the Name returned in this structure MUST be a Partial Path Name, ending
with a dot.
This list MUST include any Objects that are currently empty. An empty
Object is one that contains no instances (for a Multi-Instance Object), no
child Objects, and no child Parameters.
If NextLevel is true and ParameterPath refers to an Object that is empty,
this array MUST contain zero entries.
The ParameterList MUST include only Parameters and Objects that are
actually implemented by the CPE. If a Parameter is listed, this implies
that a GetParameterValues for this Parameter would be expected to
succeed.

Table 22 – ParameterInfoStruct definition

Name Type Description
Name string(256) This is the full Path Name of a Parameter or a Partial Path
Name.

November 2013 © The Broadband Forum. All rights reserved. Page 83 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Name Type Description

Writable boolean Whether or not the Parameter value can be overwritten
using the SetParameterValues method.
If Name is a Partial Path Name that refers to an Object,
this indicates whether or not AddObject can be used to
add new instances of this Object.
If Name is a Partial Path Name that refers to a particular
instance of a Multi-Instance Object, this indicates whether
or not DeleteObject can be used to remove this particular
instance.
This element MUST be true only if the corresponding
Parameter or Object as implemented in this CPE is
writable as described above. The value of this element
MUST reflect only the actual implementation rather than
whether or not the specification of the Parameter or Object
allows it to be writable.

The following fault codes are defined for this method: 9001, 9002, 9003, 9005.
If the fault is caused by an invalid ParameterPath value, the Invalid Parameter Name fault
code (9005) MUST be used instead of the more general Invalid Arguments fault code
(9003). A ParameterPath value MUST be considered invalid if it is not an empty string
and does not exactly match a Parameter or Object name currently present in the CPE’s
Data Model. If NextLevel is true and ParameterPath is a Parameter name rather than a
Partial Path Name, the CPE MUST return a fault response with the Invalid Arguments
fault code (9003).

A.3.2.4 SetParameterAttributes
This method MAY be used by an ACS to modify attributes associated with one or more
CPE Parameter. The calling arguments for this method are defined in Table 23. The
arguments in the response are defined in Table 24.
On successful receipt of a SetParameterAttributes RPC, the CPE MUST apply the
changes to all of the specified Parameters immediately and atomically. That is, either all
of the attribute changes are applied together, or none of the changes are applied at all. In
the latter case, the CPE MUST return a fault response indicating the reason for the failure
to apply the changes. The CPE MUST NOT apply any of the specified changes without
applying all of them. This requirement MUST hold even if the CPE experiences a crash
during the process of applying the changes.
The ACS MAY set Parameter attributes in any combination or order of its choosing using
one or multiple SetParameterAttributes RPCs.
If there is more than one entry in the ParameterList array, and the SetParameterAttributes
request is successful as described above, the CPE MUST apply the attribute changes in
the order of the ParameterList array. That is, if multiple entries in the ParameterList
would result in modifying the same attribute of a given Parameter, the attribute value
specified later in the ParameterList array MUST overwrite the attribute value specified
earlier in the array. This behavior might seem to be inconsistent with that of
SetParameterValues, for which it is an error to specify the same Parameter name more
than once; this difference is because, unlike SetParameterValues, SetParameterAttributes
permits a mixture of full and Partial Paths to be specified.

November 2013 © The Broadband Forum. All rights reserved. Page 84 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

All modifications to a CPE’s configuration resulting from use of the

SetParameterAttributes method MUST be retained across reboots of the CPE.
Attributes are associated with actual Parameter instances. If the CPE supports the Alias-
Based Addressing Mechanism, when the alias of an instance is changed and an Attribute
has been set on a Parameter whose Parameter Path includes that instance, the CPE MUST
keep the attribute on the same actual Parameter after the alias change.
When a Parameter is deleted, its attributes MUST also be deleted. Note that this means
that if another Parameter with the same Path Name as a previously deleted Parameter is
created in the future, this new Parameter will not inherit attributes from the previously
deleted Parameter.
A CPE MUST NOT allow any entity other than the ACS to modify attributes of a
Parameter.
Table 23 – SetParameterAttributes arguments
Argument Type Description
ParameterList SetParameterAttributesStruct[] List of changes to be made to the attributes for a set of
Parameters. Each entry in this array is a SetParameter-
AttributesStruct as defined in Table 25.
As described above, the order of entries in this array is
significant.

Table 24 – SetParameterAttributesResponse arguments

Argument Type Description
- void This method response has no arguments.

Table 25 – SetParameterAttributesStruct definition

Name Type Description
Name string(256) This is the name of a Parameter to apply the new
attributes. Alternatively, this MAY be a Partial Path
Name, indicating that the new attributes are to be
applied to all Parameters below this point in the
naming hierarchy. For such Parameters within Multi-
Instance Objects where the Instance Identifier is
below the specified point in the naming hierarchy, the
specified attribute values MUST only be applied within
instances that exist at the time this method is invoked.
A Partial Path Name MUST end with a “.” (dot) after
the last node name in the hierarchy. An empty string
indicates the top of the name hierarchy.
Below is an example of a full Parameter name:
InternetGatewayDevice.DeviceInfo.SerialNumber
Below is an example of a Partial Path Name:
InternetGatewayDevice.DeviceInfo.
NotificationChange boolean If true, the value of Notification replaces the current
notification setting for this Parameter or group of
Parameters. If false, no change is made to the
notification setting.
Notification int[0:6] Indicates whether (and how) the CPE will notify the
ACS when the specified Parameter(s) change in
value. The following values are defined:
0 = Notification off. The CPE need not inform the

November 2013 © The Broadband Forum. All rights reserved. Page 85 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Name Type Description

ACS of a change to the specified Parameter(s).
1 = Passive notification. Whenever the specified
Parameter value changes, the CPE MUST
include the new value in the ParameterList in the
Inform message that is sent the next time a
Session is established to the ACS.
2 = Active notification. Whenever the specified
Parameter value changes, the CPE MUST
initiate a Session to the ACS, and include the
new value in the ParameterList in the associated
Inform message.
3 = Passive lightweight notification. Whenever the
specified Parameter value changes, the CPE
MUST include the new value in the
ParameterList in the next Lightweight Notification
message that is sent.
4 = Passive notification with passive lightweight
notification. This combines the requirements of
the values 1 (Passive notification) and 3 (Passive
lightweight notification). The two mechanisms
operate independently.
5 = Active lightweight notification. Whenever the
specified Parameter value changes, the CPE
MUST include the new value in the
ParameterList in the associated Lightweight
Notification message and send that message.
6 = Passive notification with active lightweight
notification. This combines the requirements of
the values 1 (Passive notification) and 5 (Active
lightweight notification). The two mechanisms
operate independently.
For Parameters defined in the corresponding Data
Model as requiring Forced Active Notification, the
value of the Notification attribute is irrelevant and an
attempt to set it to a value other than 2 will be ignored.
Whenever a Parameter change is sent in the Inform
message due to a non-zero Notification setting, the
Event code "4 VALUE CHANGE" MUST be included
in the list of Events. The delivery of this event and
associated parameters is subject to the rules specified
in Section 3.7.1.5 (Table 8 in particular).
Note that if the CPE deletes an Object containing
Parameters for which Notification is enabled (active or
passive), this MUST NOT be considered a value-
change for the purpose of Notification.
By default, prior to any changes to this attribute by an
ACS, its value SHOULD be 0 (Notification off) unless
otherwise specified in the appropriate Data Model
definition.
The CPE MAY provide no support for Active
notification or Active lightweight notification on a
Parameter deemed inappropriate for Active
notification. A Parameter is deemed inappropriate for
Active notification if and only if that Parameter is
explicitly defined as such in the definition of the
corresponding Data Model. Parameters that might be
deemed inappropriate for Active notification include
Parameters that change frequently, such as statistics.
A CPE MUST accept a request to enable Passive
notification for any Parameter. If lightweight
notifications are supported (i.e. Notification values 3,
4, 5, and 6), the CPE MUST additionally accept
requests to enable Passive lightweight notification for
any Parameter.
Note that if a CPE implementation does not allow a
particular Parameter value to change in a manner that

November 2013 © The Broadband Forum. All rights reserved. Page 86 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Name Type Description

would result in a Notification (e.g., a capability flag
that could only change as a result of a firmware
update that requires a reboot, or a writeable
Parameter that can only be modified via the CPE
WAN Management Protocol), then support for
Notification for this Parameter involves no more than
keeping track of the value of its Notification attribute.
For such a Parameter, the CPE implementation need
not incorporate a mechanism to detect value changes
nor to initiate Notifications based on such changes.
AccessListChange boolean If true, the value of AccessList replaces the current
access list for this Parameter or group of Parameters.
If false, no change is made to the access list.
AccessList string(64)[] Array of zero or more entities for which write access
to the specified Parameter(s) is granted. If there are
no entries, write access is only allowed from an ACS.
At present, only one type of entity is defined that can
be included in this list:
“Subscriber” Indicates write access by an
interface controlled on the
subscriber LAN. Includes any
and all such LAN-side
mechanisms, which MAY include
but are not limited to TR-064
(LAN-side DSL CPE
Configuration Protocol), UPnP,
the device’s user interface, client-
side telnet, and client-side
SNMP.
Currently, access restrictions for other WAN-side
configuration protocols is not specified.
The ACS MAY further specify management entities in
the ACL using a vendor-specific prefix. If such
entities are specified by vendors, they MUST be
preceded by X_<VENDOR>_and follow the syntax for
vendor extensions for Parameter names defined in
[13].
The CPE MUST correctly interpret the value
“Subscriber” as described above, but MUST ignore
any other individual values in this array that it does
not understand.
By default, prior to any changes to the access list by
an ACS, access SHOULD be granted to all entities
specified above.
The TR-069 ACS always has write access to all
writeable Parameters regardless of being on the
access list. Other entities have write access only if
they appear on the access list. An entity that is
restricted from write access to a certain Parameter
MUST NOT be allowed to change Parameter values
and MUST NOT be allowed to delete Objects within
which the Parameter is contained. The TR-069
access control mechanism does not prevent any
entity from creating new Object instances.
The CPE MUST accept changes to the AccessList for
any Parameter even if that Parameter is read-only
and its value cannot be modified by any management
entity. For such read-only Parameters, the CPE
MUST store the modified AccessList value and return
it when requested via GetParameterAttributes, but
MAY otherwise ignore this value.

The following fault codes are defined for this method: 9001, 9002, 9003, 9004, 9005,
9009.

November 2013 © The Broadband Forum. All rights reserved. Page 87 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

If the fault is caused by an invalid Parameter name, the Invalid Parameter Name fault
code (9005) MUST be used instead of the more general Invalid Arguments fault code
(9003).
If the CPE does not support Active notifications on a Parameter deemed inappropriate (as
described above), it MUST reject an attempt to enable an Active notification for that
Parameter by responding with fault 9009 (Notification request rejected). If Active
notification is being enabled for Parameter(s) specified via a Partial Path Name and the
CPE does not support Active notification for one or more such Parameters deemed
inappropriate below this point in the naming hierarchy, the CPE MUST reject the request
and respond with fault code 9009 (Notification request rejected).
If the CPE does not support the lightweight notification mechanism, it MUST reject any
attempt to enable Passive or Active lightweight notifications (codes 3, 4, 5, 6) with fault
code 9003 (Invalid arguments).

A.3.2.5 GetParameterAttributes
This method MAY be used by an ACS to read the attributes associated with one or more
CPE Parameter. The calling arguments for this method are defined in Table 26. The
arguments in the response are defined in Table 27.
Table 26 – GetParameterAttributes arguments
Argument Type Description
ParameterNames string(256)[] Array of strings, each representing the name of a requested Parameter.
If a Parameter name argument is given as a Partial Path Name, the request is to
be interpreted as a request to return all of the Parameters in the branch of the
naming hierarchy that shares the same prefix as the argument. A Partial Path
Name MUST end with a “.” (dot) after the last node name in the hierarchy. An
empty string indicates the top of the name hierarchy.
Below is an example of a full Parameter name:
InternetGatewayDevice.DeviceInfo.SerialNumber
Below is an example of a Partial Path Name:
InternetGatewayDevice.DeviceInfo.

Table 27 – GetParameterAttributesResponse arguments

Argument Type Description
ParameterList ParameterAttributeStruct[] List of access control information for the specified set of Parameters.
Each entry in this array is a ParameterAttributeStruct as defined in
Table 25.
If multiple entries in the ParameterNames array in the
GetParameterAttributes request overlap such that there are multiple
requests for the same Parameter attribute, it is at the discretion of the
CPE whether or not to duplicate that Parameter in the response
array. That is, the CPE MAY either include that Parameter attribute
only once in its response, or it MAY include that Parameter attribute
once for each instance that it was requested
If the ParameterNames argument in the request was a Partial Path
Name, and if there are no Parameters within the Object represented
by that Partial Path Name (at any level below), the ParameterList
MUST be empty, and this MUST NOT cause an error response.

November 2013 © The Broadband Forum. All rights reserved. Page 88 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Table 28 – ParameterAttributeStruct definition

Name Type Description
Name string(256) This is the name of a Parameter to which the
attributes are given. The Name MUST be a full
Parameter name, and MUST NOT be a Partial Path
Name.
Notification int[0:6] Indicates whether (and how) the CPE will notify the
ACS when the specified Parameter(s) change in
value. The following values are defined:
0 = Notification off. The CPE need not inform the
ACS of a change to the specified Parameter(s).
1 = Passive notification. Whenever the specified
Parameter value changes, the CPE MUST
include the new value in the ParameterList in
the Inform message that is sent the next time a
Session is established to the ACS.
2 = Active notification. Whenever the specified
Parameter value changes, the CPE MUST
initiate a Session to the ACS, and include the
new value in the ParameterList in the
associated Inform message.
3 = Passive lightweight notification. Whenever the
specified Parameter value changes, the CPE
MUST include the new value in the
ParameterList in the next Lightweight
Notification message that is sent.
4 = Passive notification with passive lightweight
notification. This combines the requirements of
the values 1 (Passive notification) and 3
(Passive lightweight notification). The two
mechanisms operate independently.
5 = Active lightweight notification. Whenever the
specified parameter value changes, the CPE
MUST include the new value in the
ParameterList in the associated Lightweight
Notification message.
6 = Passive notification with active lightweight
notification. This combines the requirements of
the values 1 (Passive notification) and 5
(Active lightweight notification). The two
mechanisms operate independently.

November 2013 © The Broadband Forum. All rights reserved. Page 89 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Name Type Description

AccessList string(64)[] Array of zero or more entities for which write access
to the specified Parameter(s) is granted. If there
are no entries, write access is only allowed from an
ACS. At present, only one type of entity is defined
that can be included in this list:
“Subscriber” Indicates write access by an
interface controlled on the
subscriber LAN. Includes any
and all such LAN-side
mechanisms, which MAY
include but are not limited to
TR-064 (LAN-side DSL CPE
Configuration Protocol), UPnP,
the device’s user interface,
client-side telnet, and client-
side SNMP.
The list MAY include vendor-specific entities, which
MUST be preceded by X_<VENDOR>_and follow
the syntax for vendor extensions for Parameter
names defined in [13].
The ACS MAY ignore any individual items in this
array that it does not understand.
By default, prior to any changes to the access list by
an ACS, the AccessList attribute for all Parameters
SHOULD include all entities that the CPE supports,
indicating access granted to all of these entities.

The following fault codes are defined for this method: 9001, 9002, 9003, 9004, 9005.
If the fault is caused by an invalid Parameter name, the Invalid Parameter Name fault
code (9005) MUST be used instead of the more general Invalid Arguments fault code
(9003).

A.3.2.6 AddObject
This method MAY be used by the ACS to create a new instance of a Multi-Instance
Object. The method call takes as an argument the Path Name of the collection of Objects
for which a new instance is to be created. For example:
Top.Group.Object.
This Path Name does not include an Instance Number for the Object to be created. That
Instance Number is assigned by the CPE and returned in the response. Once assigned the
Instance Number of an Object cannot be changed and persists until the Object is deleted
using the DeleteObject method. After creation, Parameters or sub-objects within the
Object are referenced by the Path Name appended with the Instance Identifier. For
example, if the AddObject method returned an Instance Number of 2, a Parameter within
this instance can then be referred to by the path:
Top.Group.Object.2.Parameter
If the CPE supports the Alias-Based Addressing Mechanism (as defined in Section 3.6.1)
then the following are additional requirements:
 The Path Name MAY be followed by an Instance Alias (as defined in Section
A.2.2.2 ) enclosed between square brackets.

November 2013 © The Broadband Forum. All rights reserved. Page 90 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

 If the Path Name ends with an Instance Alias (enclosed between square brackets)
the CPE MUST assign the Instance Alias to the newly created Object instance.
 If the Path Name does not end with an Instance Alias, the CPE MUST assign the
newly created Object instance a unique Instance Alias using a ‘cpe-‘ prefix.
 Once assigned, an Instance Alias MUST only be changed by the ACS and it
MUST persist until the Object is deleted.
For example, to add an Object instance with its Instance Alias set to “a”:
Top.Group.Object.[a].
A new Object instance with an Instance Alias “a” will be created. After creation of an
Object instance with an Instance Alias, any Parameter within the created Object
instance can then be referred to by a Path Name such as:
Top.Group.Object.[a].Parameter
On creation of an Object using this method, the Parameters contained within the Object
MUST be set to their default values and the associated attributes MUST be set to the
following:
 Notification is set to zero (notification off) unless otherwise specified in the
appropriate Data Model definition.
 AccessList includes all defined entities.
The calling arguments for this method are defined in Table 29. The arguments in the
response are defined in Table 30.
Addition of an Object MUST be done atomically. That is, either all of the Parameters
and sub-objects are added together, or none are added. In the latter case the CPE MUST
return a fault response indicating the reason for the failure to add the Object. The CPE
MUST NOT add any contained Parameters or sub-objects as a result of this method call
without adding all of them (all Parameters and sub-objects supported by that CPE). This
requirement MUST hold even if the CPE experiences a crash during the process of
performing the addition.
If the request is valid, it is strongly RECOMMENDED that the CPE apply the Object
creation prior to sending the AddObject response. If it does so, the CPE MUST set the
value of Status in the response to 0 (zero), indicating that the Object creation has been
applied.
If the CPE requires the Session to be terminated before applying the Object creation, the
CPE MUST reply before the Object creation has been applied, and thus MUST set the
value of Status in the response to 1. In this case, the reply MUST come only after all
validation of the request has been completed and the Object creation request has been
appropriately saved such that it will definitely be applied as soon as physically possible
after the Session has terminated. Once the CPE issues the AddObject response, all
changes associated with the corresponding request (including the new ParameterKey)
MUST be available for subsequent commands to operate on, regardless of whether the
changes have been applied or not. In particular, even if the Object creation has not yet
been applied, the CPE MUST allow the use of SetParameterValues, GetParameterValues,

November 2013 © The Broadband Forum. All rights reserved. Page 91 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

SetParameterAttributes, and GetParameterAttributes to operate on Parameters within the

newly created Object, as well as the use of AddObject to create a sub-object within the
newly created Object, and DeleteObject to delete either a sub-object or the newly created
Object itself.
If the value of Status in the AddObject response is 1, the requested Object creation
MUST be applied as soon as physically possible after the Session has terminated, and no
later than the beginning of the next Session. Note that if a CPE requires a reboot to cause
the Object creation to be applied, the CPE MUST initiate that reboot on its own after the
termination of the Session. Because some CPE will not require a reboot in these
circumstances, an ACS SHOULD NOT call the Reboot method as a result of modifying
the CPE’s configuration, since this would result in an unnecessary reboot. Note also that
if application of a configuration change by the CPE would result in a service disruption
(for example, if the CPE requires a reboot to apply the requested change), it is not the
responsibility of the CPE to avoid or delay such a disruption. To minimize the impact of
such a disruption, the ACS MAY delay requesting such a configuration change until an
appropriate time, but this is entirely at the ACS’s discretion.
The use of the Status value is independent between successive SetParameterValues,
AddObject, or DeleteObject requests within the same Session. The use of a Status value
of 1 in response to one request does not necessarily imply that subsequent requests in the
same Session will also respond in the same way.
All modifications to a CPE’s configuration resulting from use of the AddObject method
MUST be retained across reboots of the CPE. This MUST include the values of Object
Instance Identifiers.
Table 29 – AddObject arguments
Argument Type Description
ObjectName string(256) The Path Name of the collection of Objects for which a new instance is to be created.
The Path Name MUST end with a “.” (dot) after the last node in the hierarchical name
of the Object, or if CPE supports the Alias-Based Addressing Mechanism, it MAY end
with the requested Instance Alias name for the new Object enclosed between square
brackets and MUST end with a “.”.
ParameterKey string(32) The value to set the ParameterKey Parameter. The CPE MUST set ParameterKey to
the value specified in this argument if and only if AddObject completes successfully. If
AddObject does not complete successfully (implying that the requested Object did not
get added), the value of ParameterKey MUST NOT be modified. ParameterKey
provides the ACS a reliable and extensible means to track changes made by the ACS.
The value of this argument is left to the discretion of the ACS, and MAY be left empty.

Table 30 – AddObjectResponse arguments

Argument Type Description
InstanceNumber UnsignedInt[1:] The Instance Number of the newly created Object. Once created, a Parameter
or sub-object within this Object can be later referenced by using this Instance
Number Identifier (defined in Section A.2.2.1) in the Path Name. The Instance
Number assigned by the CPE is arbitrary.
Note – the fact that Instance Numbers are arbitrary means that they do not
define a useful Object ordering, e.g. the ACS cannot assume that a newly-
created Object will have a higher Instance Number than its existing sibling
Objects.

November 2013 © The Broadband Forum. All rights reserved. Page 92 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Argument Type Description

Status int[0:1] A successful response to this method returns an integer enumeration defined
as follows:
0 = The Object has been created.
1 = The Object creation has been validated and committed, but not yet applied
(for example, if a reboot is required before the new Object can be applied).

The following fault codes are defined for this method: 9001, 9002, 9003, 9004 and 9005.
If an AddObject request would result in exceeding the maximum number of such Objects
supported by the CPE, the CPE MUST return a fault response with the Resources
Exceeded (9004) fault code. If an AddObject request uses an Instance Alias and requests
a new Object instance and the Instance Alias already exists, the CPE MUST return a fault
response with “Invalid Parameter Name” (9005) fault code. The same fault code (9005)
MUST be returned if the AddObject request uses an Instance Alias and the instance does
not have an Alias Parameter.

A.3.2.7 DeleteObject
This method is used to remove a particular instance of an Object. This method call takes
as an argument the Path Name of the Object instance including the Instance Identifer.
For example:
Top.Group.Object.2.
If this method call is successful, the specified instance of this Object is subsequently
unavailable for access and the CPE MUST discard the state previously associated with all
Parameters (values and attributes) and sub-objects contained within this instance.
When an Object instance is deleted, the Instance Numbers associated with any other
instances of the same collection of Objects remain unchanged. Thus, the Instance
Numbers of Object instances in a collection might not be consecutive.
The calling arguments for this method are defined in Table 31. The arguments in the
response are defined in Table 32.
If the request is valid, it is strongly RECOMMENDED that the CPE apply the Object
deletion prior to sending the DeleteObject response. If it does so, the CPE MUST set the
value of Status in the response to 0 (zero), indicating that the Object deletion has been
applied.
If the CPE requires the Session to be terminated before applying the Object deletion, the
CPE MUST reply before the Object deletion has been applied, and thus MUST set the
value of Status in the response to 1. In this case, the reply MUST come only after all
validation of the request has been completed and the Object deletion request has been
appropriately saved such that it will definitely be applied as soon as physically possible
after the Session has terminated. Once the CPE issues the DeleteObject response, all
changes associated with the corresponding request (including the new ParameterKey)
MUST be available for subsequent commands to operate on, regardless of whether the
changes have been applied or not. In particular, the use of GetParameterNames and

November 2013 © The Broadband Forum. All rights reserved. Page 93 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

GetParameterValues MUST indicate the absence of the deleted Object, and any attempt
to modify or read Parameters or sub-objects within the deleted Object MUST fail.
If the value of Status in the DeleteObject response is 1, the requested Object deletion
MUST be applied as soon as physically possible after the Session has terminated, and no
later than the beginning of the next Session. Note that if a CPE requires a reboot to cause
the Object deletion to be applied, the CPE MUST initiate that reboot on its own after the
termination of the Session. Because some CPE will not require a reboot in these
circumstances, an ACS SHOULD NOT call the Reboot method as a result of modifying
the CPE’s configuration, since this would result in an unnecessary reboot. Note also that
if application of a configuration change by the CPE would result in a service disruption
(for example, if the CPE requires a reboot to apply the requested change), it is not the
responsibility of the CPE to avoid or delay such a disruption. To minimize the impact of
such a disruption, the ACS MAY delay requesting such a configuration change until an
appropriate time, but this is entirely at the ACS’s discretion.
The use of the Status value is independent between successive SetParameterValues,
AddObject, or DeleteObject requests within the same Session. The use of a Status value
of 1 in response to one request does not necessarily imply that subsequent requests in the
same Session will also respond in the same way.
On deletion, all Parameters and sub-objects contained within this Object MUST be
removed atomically. That is, either all of the Parameters and sub-objects are removed
together, or none are removed at all. In the latter case, the CPE MUST return a fault
response indicating the reason for the failure to delete the Object. The CPE MUST NOT
remove any contained Parameters or sub-objects as a result of this method call without
removing all of them. This requirement MUST hold even if the CPE experiences a crash
during the process of performing the deletion.
All modifications to a CPE’s configuration resulting from use of the DeleteObject
method MUST be retained across reboots of the CPE.
Table 31 – DeleteObject arguments
Argument Type Description
ObjectName string(256) The Path Name of the Object instance to be removed. The Path Name MUST end
with a “.” (dot) after the Instance Identifier of the Object.
ParameterKey string(32) The value to set the ParameterKey Parameter. The CPE MUST set ParameterKey to
the value specified in this argument if and only if DeleteObject completes successfully.
If DeleteObject does not complete successfully (implying that the requested Object did
not get deleted), the value of ParameterKey MUST NOT be modified. ParameterKey
provides the ACS a reliable and extensible means to track changes made by the ACS.
The value of this argument is left to the discretion of the ACS, and MAY be left empty.

Table 32 – DeleteObjectResponse arguments

Argument Type Description
Status int[0:1] A successful response to this method returns an integer enumeration defined as follows:
0 = The Object has been deleted.
1 = The Object deletion has been validated and committed, but not yet applied (for example, if a
reboot is required before the Object can be deleted).

The following fault codes are defined for this method: 9001, 9002, 9003, 9005.

November 2013 © The Broadband Forum. All rights reserved. Page 94 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

If the fault is caused by an invalid ObjectName value, the Invalid Parameter Name fault
code (9005) MUST be used instead of the more general Invalid Arguments fault code
(9003). The ObjectName value MUST be considered invalid if it does not exactly match
the name of a single instance of a Multi-Instance Object currently present in the CPE’s
Data Model.

A.3.2.8 Download
Note – The functionality provided by this method overlaps that of the ScheduleDownload method
[Section A.4.1.8]. Unlike ScheduleDownload, this method does not provide fine-grained control
over when the download can be performed and applied. Also, this method permits a file to be
downloaded and applied within the same Session.

This method MAY be used by the ACS to cause the CPE to download a specified file
from the designated location. The calling arguments for this method are defined in Table
33. The arguments in the response are defined in Table 34.
When a download is initiated using this method, the CPE MUST indicate successful or
unsuccessful completion of the download using one of the following three means:
 A DownloadResponse with the Status argument having a value of zero (indicating
success), or a fault response to the Download request (indicating failure).
 A TransferComplete message sent later in the same Session as the Download request
(indicating either success or failure). In this case, the Status argument in the
corresponding DownloadResponse MUST have a value of one.
 A TransferComplete message sent in a subsequent Session (indicating either success
or failure). In this case, the Status argument in the corresponding DownloadResponse
MUST have a value of one.
Regardless of which means is used, the CPE MUST only indicate successful completion
of the download after the downloaded file(s) has been both successfully transferred and
applied. While the criterion used to determine when a file has been successfully applied
is specific to the CPE’s implementation, the CPE SHOULD consider a downloaded file
to be successfully applied only after the file is installed and in use as intended.
In the particular case of downloading a software image, as indicated by a “1 Firmware
Upgrade Image” FileType, the CPE MUST consider the downloaded file(s) to be
successfully applied only after the new software image is actually installed and
operational. If the software image replaces the overall software of the CPE (which would
typically require a reboot to install and begin execution), the SoftwareVersion
represented in the Data Model MUST already reflect the updated software image in the
Session in which the CPE sends a TransferComplete indicating successful download.
If the CPE requires a reboot to apply the downloaded file, then the only appropriate
means of indicating successful completion is the third option listed above—a
TransferComplete message sent in a subsequent Session.
If the file cannot be successfully downloaded or applied, the CPE MUST NOT attempt to
retry the file download on its own initiative, but instead MUST report the failure of the
download to the ACS using any of the three means listed above. Upon the ACS being

November 2013 © The Broadband Forum. All rights reserved. Page 95 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

informed of the failure of a download, the ACS MAY subsequently attempt to reinitiate
the download by issuing a new Download request.
If the CPE receives one or more Download or ScheduleDownload requests before
performing a previously requested download, the CPE MUST queue all requested
downloads and perform each of them as closely as possible to the requested time (based
on the value of the DelaySeconds argument and the time of the request). Queued
downloads MUST be retained across reboots of the CPE. The CPE MUST be able to
queue a minimum of three file transfers (downloads and uploads).
For each download performed, the CPE MUST send a distinct TransferComplete. Note
that the order in which a series of requested downloads will be performed might differ
from the order of the corresponding requests due to differing values of DelaySeconds.
For example, an ACS could request a download with DelaySeconds equal to one hour,
then five minutes later request a second download with DelaySeconds equal to one
minute. In this case, the CPE would perform the second download before the first.
All modifications to a CPE’s configuration resulting from use of the Download method
MUST be retained across reboots of the CPE.
Table 33 – Download arguments
Argument Type Description
CommandKey string(32) The string the CPE uses to refer to a particular download. This argument is
referenced in the methods Inform, TransferComplete, GetQueuedTransfers,
GetAllQueuedTransfers and CancelTransfer.
The value of the CommandKey is entirely at the discretion of the ACS and MAY be
an empty string.

November 2013 © The Broadband Forum. All rights reserved. Page 96 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Argument Type Description

FileType string(64) An integer followed by a space followed by the file type description. Only the
following values are currently defined for the FileType argument:
"1 Firmware Upgrade Image"
"2 Web Content"
“3 Vendor Configuration File”
“4 Tone File” (see [25] Appendix B)
“5 Ringer File” (see [25] Appendix B)
The following format is defined to allow the unique definition of vendor-specific file
types:
"X <VENDOR> <Vendor-specific identifier>"
<VENDOR> is replaced by a unique vendor identifier, which MAY be either an
OUI or a domain name. The OUI or domain name used for a given vendor-
specific file type MUST be one that is assigned to the organization that defined
this method (which is not necessarily the same as the vendor of the CPE or ACS).
An OUI is an organizationally unique identifier as defined in [10], which MUST be
formatted as a 6 hexadecimal-digit OUI (organizationally unique identifier), with all
upper-case letters and any leading zeros included. A domain name MUST be
upper case with each dot (“.”) replaced with a hyphen or underscore.
If and only if the CPE supports downloading of firmware images using the
Download method, the CPE MUST support the "1 Firmware Upgrade Image"
FileType value. The definition of a firmware upgrade image MAY vary across
different CPE vendors, ranging from a single monolithic image to a set of inter-
dependent files, but MUST be presented as a single URL to the CPE. For
example, a URL could be a file that contains multiple URLs and instructions on
how to upgrade the firmware image. All other FileType values are OPTIONAL.
The FileType value of "2 Web Content" is intended to be used for downloading
files that contain only web content for a CPE’s web-based user interface. A CPE
that supports a web-based user interface and allows the content to be downloaded
from the ACS via the Download method as a distinct file containing only web
content SHOULD use the FileType value of "2 Web Content" when performing
such a download. A CPE that supports a web-based user interface and allows the
content to be downloaded from the ACS MAY instead include web content as part
of its firmware upgrade image, or use some other means to update the web
content in the CPE. Such a CPE need not support the FileType value of "2 Web
Content".
The FileType value of “3 Vendor Configuration File” is intended to be used for
downloading a single vendor configuration file. A CPE MAY instead include one
or more vendor configuration files as part of its firmware upgrade image.
URL string(256) URL, as defined in [12], specifying the source file location. HTTP and HTTPS
transports MUST be supported. Other optional transports, as specified in Section
2.3.2, MAY be supported.
If the CPE receives multiple Download requests with the same source URL, the
CPE MUST perform each download as requested, and MUST NOT assume that
the content of the file to be downloaded is the same each time.
This URL MUST NOT include the “userinfo” component, as defined in [12].
Username string(256) Username to be used by the CPE to authenticate with the file server. This string is
set to the empty string if no authentication is required.
Password string(256) Password to be used by the CPE to authenticate with the file server. This string is
set to the empty string if no authentication is required.

November 2013 © The Broadband Forum. All rights reserved. Page 97 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Argument Type Description

FileSize unsignedInt The size of the file to be downloaded in bytes.
The FileSize argument is intended as a hint to the CPE, which the CPE MAY use
to determine if it has sufficient space for the file to be downloaded, or to prepare
space to accept the file.
The ACS MAY set this value to zero. The CPE MUST interpret a zero value to
mean that that the ACS has provided no information about the file size. In this
case, the CPE MUST attempt to proceed with the download under the
presumption that sufficient space is available, though during the course of
download, the CPE might determine otherwise.
The ACS SHOULD set the value of this Parameter to the exact size of the file to
be downloaded. If the value is non-zero, the CPE MAY reject the Download
request on the basis of insufficient space.
If the CPE attempts to proceed with the download based on the value of this
argument, but the actual file size differs from the value of this argument, this could
result in a failure of the download. However, the CPE MUST NOT cause the
download to fail solely because it determines that the value of this argument is
inaccurate.
TargetFileName string(256) The name of the file to be used on the target file system. This argument MAY be
left empty if the target file name can be extracted from the downloaded file itself,
or from the URL argument, or if no target file name is needed. If this argument is
specified, but the target file name is also indicated by another source (for example,
if it is extracted from the downloaded file itself), this argument MUST be ignored.
If the target file name is used, the downloaded file would replace any existing file
of the same name (whether or not the CPE archives the replaced file is a local
matter).
If present, this Parameter is treated as an opaque string with no specific
requirements for its format. That is, the TargetFileName value is to be interpreted
based on the CPE’s vendor-specific file naming conventions. Note that this
specification does not preclude the use of a file naming convention in which the
file’s path can be specified as part of the file name.

November 2013 © The Broadband Forum. All rights reserved. Page 98 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Argument Type Description

DelaySeconds unsignedInt This argument has different meanings for Unicast and Multicast downloads. For
Unicast downloads it is the number of seconds before the CPE will initiate the
download. For Multicast downloads the CPE will initiate the download
immediately and it is the number of seconds available for initiating, performing and
applying the download.
The following applies only to Unicast downloads, i.e. to downloads where the URL
specifies a Unicast download transport protocol.
The number of seconds from the time this method is called to the time the
CPE is requested to initiate the download. A value of zero indicates that no
delay is requested. If a non-zero delay is requested, the download MUST
NOT occur in the same Session in which the request was issued.
The CPE MUST perform and apply the download immediately after the time
indicated by DelaySeconds, unless this is not possible for reasons outside
the CPE’s control, in which case the CPE MUST attempt to perform and
apply the download within one hour after the time indicated by
DelaySeconds. If the CPE cannot begin the download within this time
window, the CPE MUST consider the download to have failed and report this
failure to the ACS using the TransferComplete method. If the download
completes before the end of this time window, the CPE MUST apply the
download prior to the end of this time window. If the download is still in
progress at the end of this time window, the CPE MUST apply the download
immediately upon completion of the download.
The following applies only to Multicast downloads, i.e. to downloads where the
URL specifies a Multicast download transport protocol:
The number of seconds from the time this method is called that are available
for the CPE to initiate, perform and apply the download. Multicast downloads
MUST NOT occur in the same Session in which the request was issued.
The CPE MUST perform and apply the download immediately, unless this is
not possible for reasons outside the CPE’s control, in which case the CPE
MUST attempt to perform and apply the download within DelaySeconds of
the download request. If the CPE cannot complete the download within this
time window, the CPE MUST consider the download to have failed and report
this failure to the ACS using the TransferComplete method.
The following applies to both Unicast and Multicast downloads:
The CPE MUST attempt to perform the download within the time window
specified above even if the CPE reboots one or more times prior to that time.
SuccessURL string(256) When applicable, this argument contains the URL, as defined in [12], the CPE
SHOULD redirect the user’s browser to if the download completes successfully.
This URL MAY include CGI arguments (for example, to maintain session state).
This applies only if the download was initiated via browser-based user interaction
and the CPE supports the ability to selectively redirect based on the download
results.
When there is no need for such a URL, this argument SHOULD be empty.
FailureURL string(256) When applicable, this argument contains the URL, as defined in [12], the CPE
SHOULD redirect the user’s browser to if the download does not complete
successfully. This URL MAY include CGI arguments (for example, to maintain
session state).
This applies only if the download was initiated via browser-based user interaction
and the CPE supports the ability to selectively redirect based on the download
results.
When there is no need for such a URL, this argument SHOULD be empty.

November 2013 © The Broadband Forum. All rights reserved. Page 99 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Table 34 – DownloadResponse arguments

Argument Type Description
Status int[0:1] A successful response to this method returns an integer enumeration defined as
follows:
0 = Download has completed and been applied.
1 = Download has not yet been completed and applied (for example, if the CPE needs
to reboot itself before it can perform the file download, or if the CPE needs to reboot
itself before it can apply the downloaded file).
If the value of this argument is non-zero, the CPE MUST subsequently call the
TransferComplete method to indicate the completion status of this download (either
successful or unsuccessful) either later in the same Session or in a subsequent
Session.
StartTime dateTime The date and time download was started in UTC. This need only be filled in if the
download has been completed. Otherwise, the value MUST be set to the Unknown
Time value.
CompleteTime dateTime The date and time the download was fully completed and applied in UTC. This need
only be filled in if the download has been completed. Otherwise, the value MUST be
set to the Unknown Time value.

The following fault codes are defined for this method: 9000, 9001, 9002, 9003, 9004,
9010, 9012, 9013.
If an attempt is made to queue an additional download when the CPE’s file transfer queue
is already full, the CPE MUST respond with fault 9004 (Resources exceeded). If the
CPE detects the presence of the “userinfo” component in the file source URL, it
SHOULD reject the Download request with the fault code 9003 (Invalid arguments). If
the CPE rejects the Download request because the FileSize argument exceeds the
available space on the device, it MUST use the Download Failure (9010) fault code.

A.3.2.9 Reboot
This method causes the CPE to reboot, and calls for use of extreme caution. The CPE
MUST send the method response and complete the remainder of the Session prior to
rebooting. The calling arguments for this method are defined in Table 35. The
arguments in the response are defined in Table 36.
Note – Multiple invocations of this method within a single Session MUST result in only a single
reboot. In this case the Inform following the reboot would be expected to contain a single “1
BOOT” EventCode and an “M Reboot” EventCode for each method invocation.
This method is primarily intended for troubleshooting purposes. This method is not
intended for use by an ACS to initiate a reboot after modifying the CPE’s configuration
(e.g., setting CPE Parameters or initiating a download). If a CPE requires a reboot after
its configuration is modified, the CPE MUST initiate that reboot on its own after the
termination of the Session23. Because some CPE will not require a reboot in these
circumstances, an ACS SHOULD NOT call the Reboot method as a result of modifying
the CPE’s configuration, since this would result in an unnecessary reboot.

23
The CPE SHOULD wait until all active CWMP Endpoint Sessions are terminated prior to performing the Reboot.

November 2013 © The Broadband Forum. All rights reserved. Page 100 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Table 35 – Reboot arguments

Argument Type Description
CommandKey string(32) The string to return in the CommandKey element of the InformStruct when the CPE
reboots and calls the Inform method.
The value of the CommandKey is entirely at the discretion of the ACS and MAY be an
empty string.

Table 36 – RebootResponse arguments

Argument Type Description
- void This method response has no arguments.

The following fault codes are defined for this method: 9001, 9002, 9003.

A.3.3 ACS Methods

The methods listed in this Section are defined to be supported on an ACS. Only a CPE
can call these methods.

A.3.3.1 Inform
A CPE MUST call the Inform method to initiate a transaction sequence whenever a
Session with an ACS is established. The calling arguments for this method are defined in
Table 37. The arguments in the response are defined in Table 38.
Table 37 – Inform arguments
Argument Type Value
DeviceId DeviceIdStruct A structure that uniquely identifies the CPE, defined in Table 39.
Event EventStruct[64] An array of structures, as defined in Table 8 in Section 3.7.1.5,
indicating the events that caused the Session to be established. If one
or more causes exist, the CPE MUST list all such causes. The ACS
MUST NOT place any significance on the order of events within this
array.
If a CPE needs to deliver more than 64 events in a single Inform (this
would be expected to occur only under exceptional circumstances and
on rare occasions), it MUST discard the oldest “M” (method-related)
events in order to avoid exceeding the maximum array size.
If the Session was established solely because the previous Session
terminated unsuccessfully, this array MUST NOT contain events that
have already been delivered (if all events have already been delivered
this array MUST be empty).
If further events occur while a previous failed Session is being retried,
the new events MUST be incorporated into the retried Session’s event
array.
If the CPE establishes a Session for which none of the standard event
codes apply, then this array MAY be empty.
MaxEnvelopes unsignedInt This argument MUST be set to a value of 1 because this version of the
protocol supports only a single envelope per message, and on reception
its value MUST be ignored.
CurrentTime dateTime The current date and time known to the CPE. This MUST be
represented in the local time zone of the CPE, and MUST include the
local time-zone offset from UTC (with appropriate adjustment for daylight
savings time). How the local time zone is determined by the CPE is
beyond the scope of this specification.

November 2013 © The Broadband Forum. All rights reserved. Page 101 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Argument Type Value

RetryCount unsignedInt Number of prior times an attempt was made to retry this Session.
This MUST be zero if and only if the previous Session, if any, completed
successfully, i.e. it will be reset to zero only when a Session completes
successfully.
ParameterList ParameterValueStruct[] Array of name-value pairs as specified in Table 17. This Parameter
MUST contain the name-value for the following Parameters:
 Every Parameter for which the ACS has set the Notification attribute
to either Active notification or Passive notification whose value has
been modified by an entity other than the ACS since the last
successful Inform notification (including values modified by the CPE
itself).
 Every Parameter defined in the corresponding Data Model as
requiring Forced Active Notification (regardless of the value of the
Notification attribute) for which the value has been modified by an
entity other than the ACS since the last successful Inform notification
(including values modified by the CPE itself).
 Every Parameter defined in the corresponding Data Model as being
required in every Inform.
If a Parameter has changed more than once since the last successful
Inform notification, the Parameter MUST be listed only once, with only
the most recent value given. In this case, the Parameter MUST be
included in the ParameterList even if its value has changed back to the
value it had at the time of the last successful Inform.
Whenever the CPE is re-booted, or if the ACS URL is modified, the CPE
MAY at that time clear its record of Parameters pending notification due
to a value change (though, the CPE MUST retain the values of the
Notification attribute for all Parameters). If the CPE clears its record of
Parameters pending notification due to a value change, it MUST at the
same time discard the corresponding “4 VALUE CHANGE” event.
If the value of at least one Parameter listed in the ParameterList has
been modified by an entity other than the ACS since the last successful
Inform notification to the same ACS, the Inform message MUST include
the EventCode “4 VALUE CHANGE”. This includes value changes to
any of the Parameters that are listed due to being required in every
Inform. Otherwise, the Inform message MUST NOT include the
EventCode “4 VALUE CHANGE”.
If the Inform message does include the “4 VALUE CHANGE” EventCode
then the ParameterList MUST include only those Parameters that meet
one of the three criteria listed above. If the Inform message does not
include the “4 VALUE CHANGE” EventCode, the ParameterList MAY
include additional Parameters at the discretion of the CPE.
Note that if the Inform message includes the “8 DIAGNOSTICS
COMPLETE" EventCode, the CPE is not required to include in the
ParameterList any Parameters associated with results of the
corresponding diagnostic, and as described above, if the “4 VALUE
CHANGE” EventCode is also present in the Inform, the ParameterList
MUST include only those Parameters that meet one of the three criteria
listed above.

Table 38 – InformResponse arguments

Argument Type Description
MaxEnvelopes unsignedInt This argument MUST be set to a value of 1 because this version of the protocol
supports only a single envelope per message, and on reception its value MUST be
ignored.

November 2013 © The Broadband Forum. All rights reserved. Page 102 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Table 39 – DeviceIdStruct definition

Name Type Description
Manufacturer string(64) Manufacturer of the device (for display only).
The value MUST be the same as the value of the DeviceInfo,Manufacturer
Parameter.
OUI string(6) Organizationally unique identifier of the device manufacturer. Represented
as a six hexadecimal-digit value using all upper-case letters and including
any leading zeros. The value MUST be a valid OUI as defined in [10]. The
value MUST be the same as the value of the DeviceInfo.ManufacturerOUI
Parameter.
This value MUST remain fixed over the lifetime of the device, including
across firmware updates. Any change would indicate that it is a new device
and would therefore require a BOOTSTRAP Inform.
ProductClass string(64) Identifier of the class of product for which the serial number applies. That is,
for a given manufacturer, this Parameter is used to identify the product or
class of product over which the SerialNumber Parameter is unique. The
value MUST be the same as the value of the DeviceInfo.ProductClass
Parameter.
This value MUST remain fixed over the lifetime of the device, including
across firmware updates. Any change would indicate that it is a new device
and would therefore require a BOOTSTRAP Inform.
SerialNumber string(64) Identifier of the particular device that is unique for the indicated class of
product and manufacturer. The value MUST be the same as the value of
the DeviceInfo.SerialNumber Parameter.
This value MUST remain fixed over the lifetime of the device, including
across firmware updates. Any change would indicate that it is a new device
and would therefore require a BOOTSTRAP Inform.

Table 40 – EventStruct definition

Name Type Description
EventCode string(64) Each value consists of an identifying character followed by a text description
of the cause. See Table 8 in Section 3.7.1.5 for event codes, handling rules,
and a syntax for specifying vendor-specific events.
The value of this Parameter is case sensitive and MUST exactly match
either one of the values defined in Table 8 in Section 3.7.1.5, or the vendor-
specific form also specified in that table.
CommandKey string(32) If the EventCode in this Event list entry corresponds to a cause in which a
CommandKey has been specified, this element MUST contain the value of
that CommandKey.
For this version of the specification, the following causes result in this
argument being set to the value of the CommandKey argument in the
originating method call:
 ScheduleInform method (EventCode = “M ScheduleInform”)
 Reboot method (EventCode = “M Reboot”)
 Download method (EventCode = “M Download”)
 ScheduleDownload method (EventCode = “M ScheduleDownload”)
 ChangeDUState method (EventCode = “M ChangeDUState”)
 Upload method (EventCode = “M Upload”)
For each of the above methods, the CommandKey value from the method
argument MUST appear in the Event array entry containing the EventCode
value shown above. For all other EventCode values defined in this
specification, the value of CommandKey MUST be an empty string.

The following fault codes are defined for this method: 8001, 8002, 8003, 8004, 8005,
8006.

November 2013 © The Broadband Forum. All rights reserved. Page 103 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

An ACS that receives an Inform without a “0 BOOTSTRAP” EventCode from a CPE

from which it has not previously received an Inform with the “0 BOOTSTRAP”
EventCode MAY, at its discretion, respond with a fault code of 8003 (Invalid arguments).

A.3.3.2 TransferComplete
Note – the HoldRequests SOAP Header element is DEPRECATED (see Section 3.4.7), so the
ACS SHOULD NOT send it.
This method informs the ACS of the completion (either successful or unsuccessful) of a
file transfer initiated by an earlier Download, ScheduleDownload or Upload method call.
It MUST NOT be called for a file transfer that has been successfully canceled via a
CancelTransfer method call.
This paragraph applies only when the file transfer was initiated via Download or Upload.
It does not apply to ScheduleDownload, which does not support downloading within the
same Session. TransferComplete MUST be called only when the associated Download or
Upload response indicated that the transfer had not yet completed at that time (indicated
by a non-zero value of the Status argument in the response). In such cases, it MAY be
called either later in the same Session in which the transfer was initiated or in any
subsequent Session. Note that in order for it to be called within the same Session in
which the transfer was initiated, the CPE will have been sent the InformResponse and
Download or Upload request while HoldRequests was true. When used, this method
MUST be called only after the transfer has successfully completed, and in the case of a
download, the downloaded file has been successfully applied, or after the transfer or
apply has failed. If this method fails, the CPE MUST NOT regard the ACS as having
been informed of the completion of the file transfer, and MUST attempt to call the
method again, either in the current Session or in a new Session, subject to the event
delivery rules of Section 3.7.1.5. The calling arguments for this method are defined in
Table 41. The arguments in the response are defined in Table 42.
Table 41 – TransferComplete arguments
Argument Type Value
CommandKey string(32) Set to the value of the CommandKey argument passed to CPE in the Download,
ScheduleDownload or Upload method call that initiated the transfer.
FaultStruct FaultStruct A FaultStruct as defined in Table 43. If the transfer was successful, the FaultCode is
set to zero. Otherwise a non-zero FaultCode is specified along with a FaultString
indicating the failure reason.
StartTime dateTime The date and time transfer was started in UTC. The CPE SHOULD record this
information and report it in this argument, but if this information is not available, the
value of this argument MUST be set to the Unknown Time value.
CompleteTime dateTime The date and time the transfer was fully completed and applied in UTC. This need
only be filled in if the transfer has been fully completed and applied. The CPE
SHOULD record this information and report it in this argument, but if this information is
not available or the transfer has not completed, the value of this argument MUST be
set to the Unknown Time value.

Table 42 – TransferCompleteResponse arguments

Argument Type Value
- void This method response has no arguments.

November 2013 © The Broadband Forum. All rights reserved. Page 104 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Table 43 – FaultStruct definition

Name Type Value
FaultCode unsignedInt The numerical fault code as defined in Section A.5.1. In the case of a fault, allowed
values are: 9001, 9002, 9010, 9011, 9012, 9014, 9015, 9016, 9017, 9018, 9019, 9020.
A value of 0 (zero) indicates no fault.
FaultString string(256) A human-readable text description of the fault. This field SHOULD be empty if the
FaultCode equals 0 (zero).

The following fault codes are defined for this method: 8000, 8001, 8002, 8003, 8004,
8005.

A.3.3.3 AutonomousTransferComplete
This method informs the ACS of the completion (either successful or unsuccessful) of a
file transfer that was not specifically requested by the ACS. When used, this method
MUST be called only after the transfer has successfully completed, and in the case of a
download, the downloaded file has been successfully applied, or after the transfer or
apply has failed (e.g. a timeout expired). If this method fails, the CPE MUST NOT
regard the ACS as having been informed of the completion of the file transfer, and
MUST attempt to call the method again, either in the current Session or in a new Session,
subject to the event delivery rules of Section 3.7.1.5. The calling arguments for this
method are defined in Table 44. The arguments in the response are defined in Table 45.

Table 44 – AutonomousTransferComplete arguments

Argument Type Value
AnnounceURL string(1024) The URL on which the CPE listened to the announcements that led to this transfer
being performed, or an empty string if this transfer was not performed as a result
of an announcement, or if no such URL is available.
TransferURL string(1024) The URL from or to which this transfer was performed, or an empty string if no
such URL is available.
IsDownload boolean Indicates whether the autonomous transfer was a download (true) or an upload
(false).

November 2013 © The Broadband Forum. All rights reserved. Page 105 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Argument Type Value

FileType string(64) An integer followed by a space followed by the file type description. Only the
following values are currently defined for the FileType argument:
"1 Firmware Upgrade Image" (download only)
"2 Web Content" (download only)
“3 Vendor Configuration File” (download or upload) [DEPRECATED for
upload]
“4 Vendor Log File” (upload only) [DEPRECATED]
“4 Tone File” (download only; see [25] Appendix B)
“5 Ringer File” (download only; see [25] Appendix B)
“6 Vendor Configuration File <i>” (upload only)
“7 Vendor Log File <i>” (upload only)
For “6 Vendor Configuration File <i>”, <i> is replaced by the Instance
Number from the Vendor Config File Object as defined in the appropriate
Root Data Model. The Instance Number corresponds to that of the entry in
the vendor config file table that the CPE uploaded.
For “7 Vendor Log File <i>”, <i> is replaced by the Instance Number from the
Vendor Log File Object as defined in the appropriate Root Data Model. The
Instance Number corresponds to that of the entry in the vendor log file table
that the CPE uploaded.
The following format is defined to allow the unique definition of vendor-specific file
types:
"X <VENDOR> <Vendor-specific identifier>"
<VENDOR> is replaced by a unique vendor identifier, which MAY be either an
OUI or a domain name. The OUI or domain name used for a given vendor-
specific file type MUST be one that is assigned to the organization that defined
this method (which is not necessarily the same as the vendor of the CPE or ACS).
An OUI is an organizationally unique identifier as defined in [10], which MUST be
formatted as a 6 hexadecimal-digit OUI (organizationally unique identifier), with all
upper-case letters and any leading zeros included. A domain name MUST be
upper case with each dot (“.”) replaced with a hyphen or underscore.
FileSize unsignedInt The size of the file in bytes, or zero if this information is not available or if the CPE
chooses not to make it available.
TargetFileName string(256) The name of the file on the target (CPE) file system, or an empty string if this
information is not available or if the CPE chooses not to make it available.
FaultStruct FaultStruct A FaultStruct as defined in Table 40. If the transfer was successful, the FaultCode
is set to zero. Otherwise a non-zero FaultCode is specified along with a
FaultString indicating the failure reason.
StartTime dateTime The date and time transfer was started in UTC. The CPE SHOULD record this
information and report it in this argument, but if this information is not available,
the value of this argument MUST be set to the Unknown Time value.
CompleteTime dateTime The date and time the transfer was fully completed and applied in UTC. The CPE
SHOULD record this information and report it in this argument, but if this
information is not available, the value of this argument MUST be set to the
Unknown Time value.

Table 45 – AutonomousTransferCompleteResponse arguments

Argument Type Value
- void This method response has no arguments.

The following fault codes are defined for this method: 8000, 8001, 8002, 8003, 8004,
8005.

November 2013 © The Broadband Forum. All rights reserved. Page 106 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

A.4 Optional RPC Messages

A.4.1 CPE Methods
The methods listed in this Section MAY optionally be supported on a CPE device. Only
an ACS can call these methods.

A.4.1.1 GetQueuedTransfers
Note – this method is DEPRECATED in favor of GetAllQueuedTransfers [Section
A.4.1.7].
This method MAY be used by an ACS to determine the status of previously requested
downloads or uploads. The calling arguments for this method are defined in Table 46.
The arguments in the response are defined in Table 47.
Table 46 – GetQueuedTransfers arguments
Argument Type Description
- void This method has no calling arguments.

Table 47 – GetQueuedTransfersResponse arguments

Argument Type Description
TransferList QueuedTransferStruct[16] Array of structures as defined in Table 48, each describing the state of
one transfer that the CPE has been instructed to perform, but has not
yet been fully completed.

Table 48 – QueuedTransferStruct definition

Name Type Description
CommandKey string(32) Set to the value of the CommandKey argument passed to CPE in the Download or Upload
method call that initiated the transfer.
State int[1:3] The current state of the transfer. Defined values are:
1 = Not yet started
2 = In progress
3 = Completed, finishing cleanup
All other values are reserved.

The following fault codes are defined for this method: 9000, 9001, 9002.

A.4.1.2 ScheduleInform
This method MAY be used by an ACS to request the CPE to schedule a one-time Inform
method call (separate from its periodic Inform method calls) sometime in the future. The
calling arguments for this method are defined in Table 49. The arguments in the response
are defined in Table 50.
If the CPE receives one or more ScheduleInform requests before performing a previously
requested ScheduleInform, the CPE MUST queue all requested ScheduleInform requests
and perform each of them as closely as possible to the requested time (based on the value
of the DelaySeconds argument and the time of the request). Queued ScheduleInform
requests MUST be retained across reboots of the CPE if and only if the CPE supports

November 2013 © The Broadband Forum. All rights reserved. Page 107 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

absolute time. The CPE MUST be able to queue a minimum of three ScheduleInform
requests. The CPE MUST consider a ScheduleInform that has the same non-empty
CommandKey as a previously requested (and still queued) ScheduleInform as an update
to the DelaySeconds of the previously requested ScheduleInform.
Table 49 – ScheduleInform arguments
Argument Type Description
DelaySeconds unsignedInt The number of seconds from the time this method is called to the time the CPE is
requested to initiate a one-time Inform method call. The CPE sends a response, and
then DelaySeconds later calls the Inform method. This argument MUST be greater
than zero.
CommandKey string(32) The string to return in the CommandKey element of the InformStruct when the CPE
calls the Inform method.
The value of the CommandKey is entirely at the discretion of the ACS and MAY be
an empty string.

Table 50 – ScheduleInformResponse arguments

Argument Type Description
- void This method response has no arguments.

The following fault codes are defined for this method: 9000, 9001, 9002, 9003.

A.4.1.3 SetVouchers
Note – this method, as part of the “voucher mechanism” as defined in Annex C, is
DEPRECATED in favor of the “Software Module Management mechanism” as
described in Appendix II / TR-157 Amendment 3 [29].
This method MAY be used by an ACS to set one or more option Vouchers in the CPE.
The calling arguments for this method are defined in Table 51. The arguments in the
response are defined in Table 52.
Table 51 – SetVouchers arguments
Argument Type Description
VoucherList base64[] Array of Vouchers, where each Voucher is represented as a Base64 encoded octet string.
The detailed structure of a Voucher is defined in Annex C.

Table 52 – SetVouchersResponse arguments

Argument Type Description
- void This method response has no arguments.

The following fault codes are defined for this method: 9000, 9001, 9002, 9003, 9004.

A.4.1.4 GetOptions
Note – this method, as part of the “voucher mechanism” as defined in Annex C, is
DEPRECATED in favor of the “Software Module Management mechanism” as
described in Appendix II / TR-157 Amendment 3 [29].

November 2013 © The Broadband Forum. All rights reserved. Page 108 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

This method MAY be used by an ACS to obtain a list of the options currently set in a
CPE, and their associated state information. The calling arguments for this method are
defined in Table 53. The arguments in the response are defined in Table 54.
Table 53 – GetOptions arguments
Argument Type Description
OptionName string(64) A string representing either the name of a particular Option, or an empty string indicating
the method SHOULD return the state of all Options supported by the CPE (whether or not
they are currently enabled).

Table 54 – GetOptionsResponse arguments

Argument Type Description
OptionList OptionStruct[] Array of OptionStructs as defined in Table 55, containing either a single OptionStruct if
information about a particular Option was requested, or a list of OptionStructs, one for
each option supported by the CPE.

Table 55 – OptionStruct definition

Name Type Description
OptionName string(64) Identifying name of the particular Option.
VoucherSN unsignedInt Identifying number of the particular Option.
State unsignedInt A number formed by two bits, defined as follows:
Bit 0 (LSB):
0 = Option is currently disabled
1 = Option is currently enabled
Bit 1:
0 = Option has not been setup
1 = Option has been setup
The interpretation of the setup state of an Option is Option-specific, but in
general is to be interpreted as indicating whether the end-user has
actively performed any actions required to make the Option fully
operational.
Mode int[0:2] This element specifies whether the designated Option is enabled or
disabled; and if enabled, whether or not an expiration has been specified.
The defined values are:
0 = Disabled
1 = Enabled with expiration
2 = Enabled without expiration
StartDate dateTime The specified start date for the Option in UTC. If in the future, this is the
date the Option is to be enabled. If in the past, this is the date the Option
was enabled.
This element applies only when the value of the Mode element is 1
(Enabled with expiration). When the Mode element has any other value,
StartDate MUST be set to the Unknown Time value.
ExpirationDate dateTime The specified date the Option is to expire in UTC, if any.
This element applies only when the value of the Mode element is 1
(Enabled with expiration). When the Mode element has any other value,
ExpirationDate MUST be set to the Unknown Time value.
IsTransferable boolean Indicates whether or not the Option has been designated transferable or
non-transferable (see Annex C). Defined values are:
0 = Non-transferable
1 = Transferable

The following fault codes are defined for this method: 9000, 9001, 9002, 9003.

November 2013 © The Broadband Forum. All rights reserved. Page 109 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

A.4.1.5 Upload
This method MAY be used by the ACS to cause the CPE to upload a specified file to the
designated location. The calling arguments for this method are defined in Table 56. The
arguments in the response are defined in Table 57.
If the file cannot be successfully uploaded, the CPE MUST NOT attempt to retry the file
upload on its own initiative, but instead MUST report the failure of the upload to the ACS
via either the Upload response (if it has not yet been sent) or the TransferComplete
method. Upon the ACS being informed of the failure of an upload, the ACS MAY
subsequently attempt to reinitiate the upload by issuing a new Upload request.
If the CPE receives one or more Upload requests before performing a previously
requested upload, the CPE MUST queue all requested uploads and perform each of them
as closely as possible to the requested time (based on the value of the DelaySeconds
argument and the time of the request). Queued uploads MUST be retained across reboots
of the CPE. The CPE MUST be able to queue a minimum of three file transfers
(downloads and uploads).
For each upload performed, the CPE MUST send a distinct TransferComplete. Note that
the order in which a series of requested uploads will be performed might differ from the
order of the corresponding requests due to differing values of DelaySeconds. For
example, an ACS could request an upload with DelaySeconds equal to one hour, then
five minutes later request a second upload with DelaySeconds equal to one minute. In
this case, the CPE would perform the second upload before the first.
Table 56 – Upload arguments
Argument Type Description
CommandKey string(32) The string the CPE uses to refer to a particular upload. This argument is referenced
in the methods Inform, TransferComplete, GetQueuedTransfers,
GetAllQueuedTransfers and CancelTransfer.
The value of the CommandKey is entirely at the discretion of the ACS and MAY be
an empty string.

November 2013 © The Broadband Forum. All rights reserved. Page 110 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Argument Type Description

FileType string(64) An integer followed by a space followed by the file type description. Only the
following values are currently defined for the FileType argument:
“1 Vendor Configuration File” [DEPRECATED]
“2 Vendor Log File” [DEPRECATED]
“3 Vendor Configuration File <i>”
“4 Vendor Log File <i>”
For “3 Vendor Configuration File <i>”, <i> is replaced by the Instance Number
from the Vendor Config File object as defined in the appropriate Root Data
Model. The CPE uploads the file that corresponds to that entry in the vendor
config file table.
For “4 Vendor Log File <i>”, <i> is replaced by the Instance Number from the
Vendor Log File object as defined in the appropriate Root Data Model. The
CPE uploads the file that corresponds to that entry in the vendor log file table.
The following format is defined to allow the unique definition of vendor-specific file
types:
"X <VENDOR> <Vendor-specific identifier>"
<VENDOR> is replaced by a unique vendor identifier, which MAY be either an OUI or
a domain name. The OUI or domain name used for a given vendor-specific file type
MUST be one that is assigned to the organization that defined this method (which is
not necessarily the same as the vendor of the CPE or ACS). An OUI is an
organizationally unique identifier as defined in [10], which MUST be formatted as a 6
hexadecimal-digit OUI (organizationally unique identifier), with all upper-case letters
and any leading zeros included. A domain name MUST be upper case with each dot
(“.”) replaced with a hyphen or underscore.
The FileType argument is intended to fully identify the file to be uploaded. If the
standard values listed above are insufficient to uniquely identify the file, then vendor-
specific file types MAY be used that provide more specific information to allow the
intended file to be identified.
URL string(256) URL, as defined in [12], specifying the destination file location. HTTP and HTTPS
transports MUST be supported. Other optional transports, as specified in Section
2.3.2, MAY be supported. When performing an upload to the URL specified by this
argument, the CPE MUST make use of the HTTP PUT method.
This argument specifies only the destination file location, and does not indicate in any
way the name or location of the local file to be uploaded. The local file to be
uploaded MUST be determined only by the FileType argument.
This URL MUST NOT include the “userinfo” component, as defined in [12].
Username string(256) Username to be used by the CPE to authenticate with the file server. This string is
set to the empty string if no authentication is required.
Password string(256) Password to be used by the CPE to authenticate with the file server. This string is
set to the empty string if no authentication is required.
DelaySeconds unsignedInt The number of seconds from the time this method is called to the time the CPE is
requested to initiate the upload. A value of zero indicates that no delay is requested.
If a non-zero delay is requested, the upload MUST NOT occur in the same Session in
which the request was issued.
The CPE MUST perform the upload immediately after the time indicated by
DelaySeconds, unless this is not possible for reasons outside the CPE’s control, in
which case the CPE MUST attempt to perform the upload within one hour after the
time indicated by DelaySeconds. If the CPE cannot begin the upload within this time
window, the CPE MUST consider the upload to have failed and report this failure to
the ACS using the TransferComplete method.
The CPE MUST attempt to perform the upload within the time window specified
above even if the CPE reboots one or more times prior to that time.

November 2013 © The Broadband Forum. All rights reserved. Page 111 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Table 57 – UploadResponse arguments

Argument Type Description
Status int[0:1] A successful response to this method returns an integer enumeration defined as
follows:
0 = Upload has completed.
1 = Upload has not yet completed (for example, if the upload needs to wait until after
the Session has been terminated).
If the value of this argument is non-zero, the CPE MUST subsequently call the
TransferComplete method to indicate the completion status of this upload (either
successful or unsuccessful) either later in the same Session or in a subsequent
Session.
StartTime dateTime The date and time upload was started in UTC. This need only be filled in if the upload
has been completed. Otherwise, the value MUST be set to the Unknown Time value.
CompleteTime dateTime The date and time the upload was fully completed and applied in UTC. This need only
be filled in if the upload has been completed. Otherwise, the value MUST be set to the
Unknown Time value.

The following fault codes are defined for this method: 9000, 9001, 9002, 9003, 9004,
9011, 9012, 9013.
If an attempt is made to queue an upload when the file transfer queue is already full, the
CPE MUST respond with fault 9004 (Resources exceeded). If the CPE detects the
presence of the “userinfo” component in the file destination URL, it SHOULD reject the
Upload request with the fault code 9003 (Invalid arguments).

A.4.1.6 FactoryReset
This method resets the CPE to its factory default state, and calls for use with extreme
caution. The CPE MUST initiate the factory reset procedure only after successful
completion of the Session. The calling arguments for this method are defined in Table
58. The arguments in the response are defined in Table 59.
Table 58 – FactoryReset arguments
Argument Type Description
- void This method has no arguments.

Table 59 – FactoryResetResponse arguments

Argument Type Description
- void This method response has no arguments.

The following fault codes are defined for this method: 9000, 9001, 9002, 9003.

A.4.1.7 GetAllQueuedTransfers
This method MAY be used by an ACS to determine the status of all queued downloads
and uploads, including any that were not specifically requested by the ACS, i.e.
autonomous transfers. The calling arguments for this method are defined in Table 60.
The arguments in the response are defined in Table 61.

November 2013 © The Broadband Forum. All rights reserved. Page 112 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Table 60 – GetAllQueuedTransfers arguments

Argument Type Description
- void This method has no calling arguments.

Table 61 – GetAllQueuedTransfersResponse arguments

Argument Type Description
TransferList AllQueuedTransferStruct[16] Array of structures as defined in Table 62, each describing the state
of one transfer that has not yet been fully completed.

Table 62 – AllQueuedTransferStruct definition

Name Type Description
CommandKey string(32) Set to the value of the CommandKey argument passed to CPE in the Download,
ScheduleDownload or Upload method call that initiated the transfer, or an empty
string for an autonomous transfer.
State int[1:3] The current state of the transfer. Defined values are:
1 = Not yet started
2 = In progress
3 = Completed, finishing cleanup
All other values are reserved.
IsDownload boolean Indicates whether the transfer is a download (true) or an upload (false).
FileType string(64) An integer followed by a space followed by the file type description. Only the
following values are currently defined for the FileType argument:
"1 Firmware Upgrade Image" (download only)
"2 Web Content" (download only)
“3 Vendor Configuration File” (download or upload) [DEPRECATED for
upload]
“4 Vendor Log File” (upload only) [DEPRECATED]
“4 Tone File” (download only; see [25] Appendix B)
“5 Ringer File” (download only; see [25] Appendix B)
“6 Vendor Configuration File <i>” (upload only)
“7 Vendor Log File <i>” (upload only)
For “6 Vendor Configuration File <i>”, <i> is replaced by the Instance Number
from the Vendor Config File object as defined in the appropriate Root Data
Model. The Instance Number corresponds to that of the entry in the vendor
config file that the CPE had been instructed to upload.
For “7 Vendor Log File <i>”, <i> is replaced by the Instance Number from the
Vendor Log File object as defined in the appropriate Root Data Model. The
Instance Number corresponds to that of the entry in the vendor log file table
that the CPE had been instructed to upload.
The following format is defined to allow the unique definition of vendor-specific file
types:
"X <VENDOR> <Vendor-specific identifier>"
<VENDOR> is replaced by a unique vendor identifier, which MAY be either an
OUI or a domain name. The OUI or domain name used for a given vendor-
specific file type MUST be one that is assigned to the organization that defined
this method (which is not necessarily the same as the vendor of the CPE or ACS).
An OUI is an organizationally unique identifier as defined in [10], which MUST be
formatted as a 6 hexadecimal-digit OUI (organizationally unique identifier), with all
upper-case letters and any leading zeros included. A domain name MUST be
upper case with each dot (“.”) replaced with a hyphen or underscore.
FileSize unsignedInt The size of the file in bytes, or zero if this information is not available or if the CPE
chooses not to make it available.
TargetFileName string(256) The name of the file on the target (CPE) file system, or an empty string if this
information is not available or if the CPE chooses not to make it available.

November 2013 © The Broadband Forum. All rights reserved. Page 113 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

The following fault codes are defined for this method: 9000, 9001, 9002.

A.4.1.8 ScheduleDownload
Note – the functionality provided by this method overlaps that of the Download method [Section
A.3.2.8]. Unlike Download, this method provides fine-grained control over when the download
can be performed and applied. Also, this method does not permit a file to be downloaded and
applied within the same Session.
This method MAY be used by the ACS to cause the CPE to download a specified file
from the designated location and apply it within either one or two specified time
windows. The CPE MUST support two time windows. The calling arguments for this
method are defined in Table 63. The arguments in the response are defined in Table 64.
When a download is initiated using this method, the CPE MUST indicate successful or
unsuccessful completion of the download via a TransferComplete message sent in a
subsequent Session.
The CPE MUST only indicate successful completion of the download after the
downloaded file(s) has been both successfully transferred and applied. While the criterion
used to determine when a file has been successfully applied is specific to the CPE’s
implementation, the CPE SHOULD consider a downloaded file to be successfully applied
only after the file is installed and in use as intended.
In the particular case of downloading a software image, the CPE MUST consider the
downloaded file(s) to be successfully applied only after the new software image is
actually installed and operational. If the software image replaces the overall software of
the CPE (which would typically require a reboot to install and begin execution), the
software version represented in the Data Model MUST already reflect the updated
software image in the Session in which the CPE sends a TransferComplete indicating
successful download.
If the file cannot be successfully downloaded or applied within the boundaries of the
specified time windows, the CPE MUST NOT attempt to retry the file download on its
own initiative, but instead MUST report the failure of the download to the ACS. Upon
the ACS being informed of the failure of a download, the ACS MAY subsequently
attempt to reinitiate the download by issuing a new ScheduleDownload request.
If an unrecoverable error occurs during a download, e.g. the file is not accessible or is
corrupted, the file transfer MUST be aborted, even if the failure occurred on the first of
two time windows.
If the CPE receives one or more Download or ScheduleDownload requests before
performing a previously requested download, the CPE MUST queue all requested
downloads and perform each of them as closely as possible to the requested time (based
on the values of WindowStart in the time windows and the time of the request). Queued
downloads MUST be retained across reboots and firmware upgrades of the CPE. The
CPE MUST be able to queue a minimum of three file transfers (downloads and uploads).
For each download performed, the CPE MUST send a distinct TransferComplete. Note
that the order in which a series of requested downloads will be performed might differ
from the order of the corresponding requests due to differing time windows. For

November 2013 © The Broadband Forum. All rights reserved. Page 114 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

example, an ACS could request a download with a time window starting in one hour, then
five minutes later request a second download with a time window starting in one minute.
In this case, the CPE would perform the second download before the first.
All modifications to a CPE’s configuration resulting from use of the ScheduleDownload
method MUST be retained across reboots of the CPE.
If (and only if) the file transfer does not impact subscriber services, a CPE MAY transfer
the file outside of a time window. For example, this might be the case for CPE which use
Multicast streams for downloads. However, the CPE MUST never apply a downloaded
file outside of a time window.
Table 63 – ScheduleDownload arguments
Argument Type Description
CommandKey string(32) The string the CPE uses to refer to a particular download. This argument is
referenced in the methods Inform, TransferComplete, GetQueuedTransfers,
GetAllQueuedTransfers and CancelTransfer.
The value of the CommandKey is entirely at the discretion of the ACS and MAY be
an empty string.
FileType string(64) An integer followed by a space followed by the file type description. Only the
following values are currently defined for the FileType argument:
"1 Firmware Upgrade Image"
"2 Web Content"
“3 Vendor Configuration File”
“4 Tone File” (see [25] Appendix B)
“5 Ringer File” (see [25] Appendix B)
The following format is defined to allow the unique definition of vendor-specific file
types:
"X <VENDOR> <Vendor-specific identifier>"
<VENDOR> is replaced by a unique vendor identifier, which MAY be either an OUI
or a domain name. The OUI or domain name used for a given vendor-specific file
type MUST be one that is assigned to the organization that defined this method
(which is not necessarily the same as the vendor of the CPE or ACS). An OUI is an
organizationally unique identifier as defined in [10], which MUST be formatted as a 6
hexadecimal-digit OUI (organizationally unique identifier), with all upper-case letters
and any leading zeros included. A domain name MUST be upper case with each
dot (“.”) replaced with a hyphen or underscore.
If and only if the CPE supports downloading of firmware images using the
ScheduleDownload method, the CPE MUST support the "1 Firmware Upgrade
Image" FileType value. The definition of a firmware upgrade image MAY vary
across different CPE vendors, ranging from a single monolithic image to a set of
inter-dependent files, but MUST be presented as a single URL to the CPE. For
example, a URL could be a file that contains multiple URLs and instructions on how
to upgrade the firmware image. All other FileType values are OPTIONAL.
The FileType value of "2 Web Content" is intended to be used for downloading files
that contain only web content for a CPE’s web-based user interface. A CPE that
supports a web-based user interface and allows the content to be downloaded from
the ACS via the ScheduleDownload method as a distinct file containing only web
content SHOULD use the FileType value of "2 Web Content" when performing such
a download. A CPE that supports a web-based user interface and allows the
content to be downloaded from the ACS MAY instead include web content as part of
its firmware upgrade image, or use some other means to update the web content in
the CPE. Such a CPE need not support the FileType value of "2 Web Content".
The FileType value of “3 Vendor Configuration File” is intended to be used for
downloading a single vendor configuration file. A CPE MAY instead include one or
more vendor configuration files as part of its firmware upgrade image.

November 2013 © The Broadband Forum. All rights reserved. Page 115 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Argument Type Description

URL string(256) URL, as defined in [12], specifying the source file location. HTTP and HTTPS
transports MUST be supported. Other optional transports, as specified in Section
2.3.2, MAY be supported.
If the CPE receives multiple ScheduleDownload requests with the same source
URL, the CPE MUST perform each download as requested, and MUST NOT
assume that the content of the file to be downloaded is the same each time.
This URL MUST NOT include the “userinfo” component, as defined in [12].
Username string(256) Username to be used by the CPE to authenticate with the file server. This string is
set to the empty string if no authentication is required.
Password string(256) Password to be used by the CPE to authenticate with the file server. This string is
set to the empty string if no authentication is required.
FileSize unsignedInt The size of the file to be downloaded in bytes.
The FileSize argument is intended as a hint to the CPE, which the CPE MAY use to
determine if it has sufficient space for the file to be downloaded, or to prepare space
to accept the file.
The ACS MAY set this value to zero. The CPE MUST interpret a zero value to
mean that that the ACS has provided no information about the file size. In this case,
the CPE MUST attempt to proceed with the download under the presumption that
sufficient space is available, though during the course of download, the CPE might
determine otherwise.
The ACS SHOULD set the value of this Parameter to the exact size of the file to be
downloaded. If the value is non-zero, the CPE MAY reject the ScheduleDownload
request on the basis of insufficient space.
If the CPE attempts to proceed with the download based on the value of this
argument, but the actual file size differs from the value of this argument, this could
result in a failure of the download. However, the CPE MUST NOT cause the
download to fail solely because it determines that the value of this argument is
inaccurate.
TargetFile- string(256) The name of the file to be used on the target file system. This argument MAY be left
Name empty if the target file name can be extracted from the downloaded file itself, or from
the URL argument, or if no target file name is needed. If this argument is specified,
but the target file name is also indicated by another source (for example, if it is
extracted from the downloaded file itself), this argument MUST be ignored. If the
target file name is used, the downloaded file would replace any existing file of the
same name (whether or not the CPE archives the replaced file is a local matter).
If present, this Parameter is treated as an opaque string with no specific
requirements for its format. That is, the TargetFileName value is to be interpreted
based on the CPE’s vendor-specific file naming conventions. Note that this
specification does not preclude the use of a file naming convention in which the file’s
path can be specified as part of the file name.
TimeWindow- TimeWin- This structure defines the time window(s) during which the CPE MUST perform and
List dowStr- apply the download. As noted earlier, if a file transfer does not generate additional
uct[1:2] network traffic and does not impact subscriber services, the CPE is permitted to
perform (but not apply) the download outside of a time window.
A CPE MUST be able to accept a request with either one or two TimeWindowStruct
elements.
The time windows MUST NOT overlap, i.e. if there are two time windows, the
second window’s WindowStart value has to be greater than or equal to the first
window’s WindowEnd value.

Table 64 – ScheduleDownloadResponse arguments

Argument Type Description
- void This method response has no arguments.

November 2013 © The Broadband Forum. All rights reserved. Page 116 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Table 65 – TimeWindowStruct definition

Name Type Description
WindowStart unsignedInt Start of this time window as an offset in seconds after receiving the
download request. An offset is used in order to avoid a
dependence on absolute time.
WindowEnd unsignedInt End of this time window as an offset in seconds after receiving the
download request. An offset is used in order to avoid a
dependence on absolute time.
WindowMode string(64) An integer followed by a space followed by the time window mode
description. The following values are currently defined:
“1 At Any Time”
“2 Immediately”
“3 When Idle”
“4 Confirmation Needed”
The following format is defined to allow for the unique definition of
vendor-specific time window modes:
“X <VENDOR> <Vendor specific identifier>”
<VENDOR> is replaced by a unique vendor identifier, which MAY
be either an OUI or a domain name. The OUI or domain name
used for a given vendor-specific file type MUST be one that is
assigned to the organization that defined this method (which is not
necessarily the same as the vendor of the CPE or ACS). An OUI
is an organizationally unique identifier as defined in [10], which
MUST be formatted as a 6 hexadecimal-digit OUI (organizationally
unique identifier), with all upper-case letters and any leading zeros
included. A domain name MUST be upper case with each dot (“.”)
replaced with a hyphen or underscore.
WindowMode specifies when within this time window the CPE is
permitted to perform and apply the download. As noted earlier, if a
file transfer does not impact subscriber services, the CPE is
permitted to perform (but not apply) the download outside of a time
window.
The CPE MUST support “1 At Any Time”. This means that the
CPE MAY perform and apply a download at any time during the
time window even if this results in interruption of service for the
subscriber.
The CPE MUST support “2 Immediately”. This means that the
CPE MUST perform and apply a download immediately at the start
of the time window even if this results in interruption of service for
the subscriber.
The CPE MUST support “3 When Idle”. This means that
interruption of service from the subscriber standpoint MUST NOT
occur during the time window. How the CPE determines this is
outside the scope of this specification.
The CPE MAY support “4 Confirmation Needed”. This means that
the CPE MUST ask for and receive confirmation before performing
and applying the download. It is outside the scope of this
specification how the CPE asks for and receives this confirmation.
If confirmation is not received, this time window MUST NOT be
used.
UserMessage string(256) A message to the user of the CPE, to inform him about a download
request. The CPE MAY use this message when seeking
confirmation from the user, e.g. when WindowMode is “4
Confirmation Needed”.
When there is no need for such a message, it SHOULD be empty
and MUST be ignored.
MaxRetries int The maximum number of retries for downloading and/or applying
the file before regarding the transfer as having failed. Refers only
to this time window (each time window can specify its own value).
A value of 0 means “No retries are permitted”. A value of -1
means “the CPE determines the number of retries”, i.e. that the
CPE can use its own retry policy, not that it has to retry forever.

November 2013 © The Broadband Forum. All rights reserved. Page 117 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

The following fault codes are defined for this method: 9000, 9001, 9002, 9003, 9004,
9010, 9013.
If an attempt is made to queue an additional download when the CPE’s file transfer queue
is already full, the CPE MUST respond with fault 9004 (Resources exceeded). If the
CPE detects the presence of the “userinfo” component in the file source URL, or detects
overlapping or otherwise invalid time windows (including zero windows supplied, or
unsupported time window modes), it SHOULD reject the ScheduleDownload request
with the fault code 9003 (Invalid arguments). If the CPE rejects the ScheduleDownload
request because the FileSize argument exceeds the available space on the device, it
MUST use the Download Failure (9010) fault code.

A.4.1.9 CancelTransfer
This method MAY be used by the ACS to cause the CPE to cancel a file transfer initiated
by an earlier Download, ScheduleDownload or Upload method call. The
TransferComplete method is not called for a file transfer that has successfully been
canceled. The calling arguments for this method are defined in Table 66. The arguments
in the response are defined in Table 67.
Table 66 – CancelTransfer arguments
Name Type Description
CommandKey string(32) The command key that was provided in the original Download,
Upload or ScheduleDownload RPC.

Table 67 – CancelTransferResponse arguments

Name Type Description
- void This method response has no arguments

The following fault codes are defined for this method: 9000, 9001, 9004, 9021.
The CPE might be unable to cancel an active transfer, e.g. the file might currently be
being downloaded in an uninterruptible way, or the CPE might be just about to apply the
downloaded file. In this case, the CPE MUST respond with fault 9021 (Cancelation of
file transfer not permitted in current transfer state). If the ACS is planning to cancel
transfers, it SHOULD use a unique command key for each transfer. However, if the
command key matches more than one transfer, the CPE MUST attempt to cancel all the
matching transfers, and MUST respond with fault 9021 (described above) if it is unable
to cancel all of them, in which case it SHOULD cancel as many matching transfers as it
can. It is not an error to specify an invalid command key.

A.4.1.10 ChangeDUState
Appendix II / TR-157 Amendment 3 [29] details a Theory of Operation for Software Module
Management, including defining the implicit and explicit state transitions for a DU.
This method MAY be used by an ACS to trigger the explicit state transitions of Install,
Update, and Uninstall for a Deployment Unit (DU), i.e. installing a new DU, updating an
existing DU, or uninstalling an existing DU. The calling arguments for this method are
defined in Table 68. The arguments in the response are defined in Table 69.

November 2013 © The Broadband Forum. All rights reserved. Page 118 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

When a DU state change is initiated using this method the CPE MUST indicate
successful or unsuccessful completion of the state change via the
DUStateChangeComplete method sent in a subsequent Session or via a CWMP fault sent
within the same Session.
The ChangeDUState method MUST include one or more DU operations within a single
method call, where a DU operation is described by one of the three types of operation
structures (OperationStruct) that are defined in Table 70. There MUST, however, be only
one resultant DUStateChangeComplete method for each ChangeDUState method issued
by the ACS, and the DUStateChangeComplete MUST contain at least one result for each
operation, including both successful and unsuccessful operations. The CPE MAY apply
the operations in any order it chooses, but it MUST report the results for each operation
in the same order as they were sent in the request. If the ACS wants to effect multiple
state transitions for the same DU, then it SHOULD utilize multiple ChangeDUState
RPCs to do so.
Regardless of the order in which the operations are applied, the CPE MUST complete
each operation within one hour. If the CPE is unable to do so, it MUST consider that
specific operation in error and send the appropriate FaultStruct in the resulting
DUStateChangeComplete method call.
The CPE MUST send the related DUStateChangeComplete RPC within 24 hours of
responding to the ChangeDUState method. If the CPE has not been able to complete all
of the operations within that 24 hour time window, it MUST consider the remaining
operations in error and send the appropriate FaultStruct within the resulting
DUStateChangeComplete RPC.
If the ACS sends a request that contains more operation structures than the CPE can
handle, the CPE MAY respond with a “Resources exceeded” (9004) CWMP Fault. The
CPE MUST, however, be able to accept a minimum of sixteen (16) operation structures
within a single request without issuing a “Resources exceeded” (9004) CWMP Fault.
If a DU state change fails, the CPE MUST NOT attempt to retry the state change on its
own initiative, but instead MUST report the failure of the operation to the ACS using the
DUStateChangeComplete method. Upon the ACS being informed of operation failure
the ACS MAY subsequently attempt to reinitiate the DU state change by issuing a new
ChangeDUState request.
Each DU operation contains an argument called UUID, which enables an ACS to
uniquely identify a DU across CPE. The UUID is also a part of the Deployment Unit
table’s unique key, along with the version of the DU and the Execution Environment that
the DU is installed against. The format of the UUID and rules for generating the UUID
are defined in RFC 4122 [34]. Additional rules for generating the UUIDs for Software
Module Management are defined in Annex H. If the rules defined in RFC 4122 and
Annex H are adhered to, both an ACS and a CPE will generate an equivalent UUID.
All modifications to a CPE’s configuration resulting from use of the ChangeDUState
method MUST be retained across reboots of the CPE.

November 2013 © The Broadband Forum. All rights reserved. Page 119 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Table 68 – ChangeDUState Arguments

Argument Type Description
Operations OperationStruct The set of DU-related operations to be performed. The argument can contain any
combination of the various OperationStruct types.
CommandKey string(32) The string the CPE uses to refer to a particular ChangeDUState. This argument is
referenced in the methods Inform and DUStateChangeComplete. The value of the
CommandKey is entirely at the discretion of the ACS and MAY be an empty string.

Table 69 – ChangeDUStateResponse Arguments

Argument Type Description
- void This method response has no arguments.

Table 70 – OperationStruct Types

Name Type Description
InstallOpStruct OperationStruct This is a type of OperationStruct used to Install new DUs on an Execution
Environment.
UpdateOpStruct OperationStruct This is a type of OperationStruct used to Update existing DUs on an
Execution Environment.
UninstallOpStruct OperationStruct This is a type of OperationStruct used to Uninstall existing DUs from an
Execution Environment.

The three OperationStruct types in this table correspond to the three different explicit
actions defined in the State Diagram in Appendix II / TR-157 Amendment 3 [29]. These
are the structures that are allowed to appear in the Operations argument of the
ChangeDUState RPC.
Table 71 – InstallOpStruct Definition
Name Type Description
URL string(1024) The URL, as defined in RFC 3986 [12], that specifies the location of the DU to
be installed. HTTP and HTTPS transports MUST be supported. Other optional
transports, as specified in Section 2.3.2, MAY be supported. If the CPE receives
multiple Install requests with the same source URL, the CPE MUST perform
each Install as requested, and MUST NOT assume that the content of the file to
be downloaded is the same each time.
This URL MUST NOT include the “userinfo” component, as defined in RFC 3986
[12].
UUID string(36) The UUID (see RFC 4122 [34] and Annex H) of the DU to be installed. The ACS
MAY send down an empty string in which case the CPE MUST generate the
UUID based on the rules defined in RFC 4122 [34] and Annex H.
Username string(256) Username to be used by the CPE to authenticate with the file server, if
authentication is required.
Password string(256) Password to be used by the CPE to authenticate with the file server, if
authentication is required.
ExecutionEnvRef string(256) A reference to the Execution Environment upon which the DU is to be installed.
This argument is the Path Name of the Execution Environment Object instance,
including its Instance Identifier. The Path Name MUST end with a “.” (dot) after
the Instance Identifier of the Object.
If this string is either not provided or sent in as an empty string, the CPE MUST
choose which Execution Environment to use.

November 2013 © The Broadband Forum. All rights reserved. Page 120 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Table 72 – UpdateOpStruct Definition

Name Type Description
UUID string(36) The UUID (see RFC 4122 [34] and Annex H) of the existing DU that is to be updated.
Version string(32) The Version indicates which version of the DU to update when there are multiple versions
available. If there are multiple versions available, this argument MUST be specified.
URL string(1024) The URL, as defined in RFC 3986 [12], that specifies the location of the update to be
applied to the existing DU(s). HTTP and HTTPS transports MUST be supported. Other
optional transports, as specified in Section 2.3.2, MAY be supported. If the CPE receives
an Update request with the same source URL as a previous Update or Install, the CPE
MUST perform each Update as requested, and MUST NOT assume that the content of the
file to be downloaded is the same each time.
This URL MUST NOT include the “userinfo” component, as defined in RFC 3986 [12].
Username string(256) Username to be used by the CPE to authenticate with the file server, if authentication is
required.
Password string(256) Password to be used by the CPE to authenticate with the file server, if authentication is
required.

The combination of the UUID and URL determine which DU(s) will be updated. There
are four possibilities (NOTE: if the URL is empty then the Username and Password
SHOULD also be empty):
 UUID populated, URL empty: The CPE MUST Update the DU with the matching UUID based on
its internal URL (the CPE SHOULD use the credentials that were last used to Install or Update
this DU)
 UUID empty, URL populated: The CPE MUST Update the DU that last used the URL at either
Install or Update (i.e. matches the URL Parameter in the DeploymentUnit.{i}. table)
 UUID populated, URL populated: The CPE MUST Update the DU with the matching UUID and
update its internal URL
 UUID empty, URL empty: The CPE MUST Update all DUs based on their internal URL (the CPE
SHOULD use the credentials that were last used to Install or Update the DU)
Note that because this option [UUID empty, URL empty] is intended to update all DUs, the
Version MUST NOT be specified. If the Version is specified, the CPE SHOULD consider this
operation in fault using 9003 as the fault code.
Table 73 – UninstallOpStruct Definition
Name Type Description
UUID string(36) The UUID (see RFC 4122 [34] and Annex H) of the existing DU that is to be
uninstalled.
Version string(32) The version of the DU to be uninstalled. If this argument is not provided or is an
empty string, all versions of the DU with the corresponding UUID are uninstalled.
ExecutionEnvRef string(256) A reference to the Execution Environment that the DU is to be uninstalled from.
This argument is the Path Name of the Execution Environment Object instance,
including its Instance Identifier. The Path Name MUST end with a “.” (dot) after
the Instance Identifier of the Object.
If this string is either not provided or sent in as an empty string, the CPE MUST
uninstall this DU from all Execution Environments that it is installed on.

The following fault codes are defined for this method: 9000, 9001, 9002, and 9004.
These are the fault codes for the RPC as a whole; there can also be faults reported against
specific operations contained in the DUStateChangeComplete FaultStruct (see A.4.2.3 for
more details regarding the faults related to the individual operations). Appendix II.5 /
TR-157 Amendment 3 [29] provides a description of the Software Module Management
faults.

November 2013 © The Broadband Forum. All rights reserved. Page 121 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

If the ACS sends a request that contains more operation structures than the CPE can
handle, the CPE MAY respond with a 9004 (Resources Exceeded) CWMP Fault. Note
that this scenario is differentiated from the 9027 (System Resources Exceeded) fault
described in A.4.2.3, in which the CPE does not have the resources to perform the install
or update of the DU.

A.4.2 ACS Methods

The methods listed in this Section MAY optionally be supported on an ACS. Only a
CPE can call these methods.

A.4.2.1 Kicked
Note – this method is DEPRECATED due to the deprecation of Annex D, which defined the usage
of this RPC.
The CPE calls this method whenever the CPE is “kicked” as described in Annex D. The
calling arguments for this method are defined in Table 74. The arguments in the response
are defined in Table 75.
Table 74 – Kicked arguments
Argument Type Value
Command string(32) Generic argument that MAY be used by the ACS for identification or other purposes.
Referer string(64) The content of the “Referer” HTTP header sent to the CPE when it was kicked.
Arg string(256) Generic argument that MAY be used by the ACS for identification or other purposes.
Next string(1024) The URL the ACS SHOULD return in the method response under normal conditions.

Table 75 – KickedResponse arguments

Argument Type Value
NextURL string(1024) The next URL the user’s browser SHOULD be redirected to. This URL MAY include CGI
arguments (for example, to maintain session state).
If the ACS wishes to send the user’s browser to a page on the CPE device itself, only the
path portion of the URL is returned as a result (e.g. “/security/index.html”). This allows the
CPE to use its canonical hostname in the HTTP 302 response. Note that this would require
the ACS to have previous knowledge of available URLs on the CPE device through some
mechanism outside the scope of this specification.

If this method returns a fault, the CPE SHOULD redirect the browser to an error page
resident on the CPE device.
The following fault codes are defined for this method: 8000, 8001, 8002, 8003, 8005.

A.4.2.2 RequestDownload
This method allows the CPE to request a file download from the ACS. On reception of
this request, the ACS MAY call the Download method to initiate the download. The
calling arguments for this method are defined in Table 76. The arguments in the response
are defined in Table 77.
Table 76 – RequestDownload arguments
Argument Type Value
FileType string(64) This is the FileType being requested (see Table 33 for the list of allowed file types).

November 2013 © The Broadband Forum. All rights reserved. Page 122 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Argument Type Value

FileTypeArg ArgStruct[16] Array of zero or more additional arguments, where each argument is a structure of
name-value pairs as defined in Table 78. The use of the additional arguments
depend on the FileType specified.
The following arguments are defined for each of the currently defined file types.
FileType FileTypeArg Names
1 Firmware Upgrade (none)
2 Web Content “Version”
3 Vendor Configuration File (none)
4 Tone File (none)
(see [25] Appendix B)
5 Ringer File (none)
(see [25] Appendix B)

If the ACS receives arguments that it does not understand, it MUST ignore the
unknown arguments, but process the request using the arguments that it does
understand.

Table 77 – RequestDownloadResponse arguments

Argument Type Description
- void This method response has no arguments.

Table 78 – ArgStruct definition

Name Type Description
Name string(64) Argument name.
Value string(256) Argument value.

The following fault codes are defined for this method: 8000, 8001, 8002, 8003, 8005.

A.4.2.3 DUStateChangeComplete
This method informs the ACS of the completion of an earlier requested ChangeDUState
method call, including both successful and unsuccessful operations. This method MUST
be called only after the CPE has completed any file transfers related to the
ChangeDUState request and attempted all of the operations specified in the
ChangeDUState request, or if the ChangeDUState request times out. If the ACS fails the
DUStateChangeComplete method, the CPE MUST NOT regard the ACS as having been
informed of the completion of the file transfer, and MUST attempt to call the method
again, either in the current Session or in a new Session, subject to the event delivery rules
of Section 3.7.1.5.
There MUST be exactly one DUStateChangeComplete method for each ChangeDUState
method called. The DUStateChangeComplete method MUST contain the results,
whether success or failure, for each of the requested operations in the ChangeDUstate
request. The entries in the Results argument MUST be in the same order as in the
requesting ChangeDUState method, although the order in which the CPE actually applies
the changes is up to the CPE implementation. There are situations in which a single

November 2013 © The Broadband Forum. All rights reserved. Page 123 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

ChangeDUState operation affects multiple Deployment Units. In this case there MUST
be an OpResultStruct entry for each affected DU contained within the Results argument.
The calling arguments for this method are defined in Table 79. The arguments in the
response are defined in Table 82.
Table 79 – DUStateChangeComplete Arguments
Name Type Description
Results OpResultStruct… The results of Operations performed against DUs.
CommandKey string(32) The value of the CommandKey argument passed to the
CPE in the corresponding ChangeDUState method call.

Table 80 – OpResultStruct Definition

Name Type Description
UUID string(36) The UUID as defined in RFC 4122 [34] of the DU that was affected. In
the case of an Install, this will be the UUID of the DU that was created. In
the case of an Update or Uninstall, it will be the existing UUID of the DU
that was either updated or uninstalled.
DeploymentUnitRef string(256) A reference to the DU affected. In the case of an Install, this is the DU
that was created. In the case of an Update, this is the DU that was
updated. In the case of an Uninstall, this is the DU that was removed.
The DU reference is a full Path Name of the DeploymentUnit Object
instance, including its Instance Identifier. The Path Name MUST end with
a “.” (dot) after the Instance Identifier of the Object.
Version string(32) The version of the DU affected. This MUST match the Version Parameter
contained within the instance of the DeploymentUnit that is contained
within the DeploymentUnitRef argument. In the case of an Install, this will
be the version of the DU created. In the case of an Update, it will be the
updated version of the DU. In the case of an Uninstall, it will be the
version of the uninstalled DU.
CurrentState string The current state of the affected DU. This state was attained either by
completing a requested Operation in the ChangeDUState method or
reflects the state of the DU after a failed attempt to change its state.
The following values are defined:
* Installed: The DU is in an Installed state due to one of the following:
successful Install, successful Update, failed Update, or failed Uninstall. In
the case of a failed Update or failed Uninstall the Fault argument will
contain an explanation of the failure.
* Uninstalled: The DU was successfully Uninstalled from the device.
* Failed: The DU could not be installed in which case a DU instance
MUST NOT be created in the Data Model.
Resolved boolean Whether or not the DU operation resolved all of its dependencies. In the
case of an Uninstall, this value is meaningless and SHOULD be true.
ExecutionUnitRefList string A comma-separated list of the Execution Units related to the affected DU.
Each Execution Unit (EU) in the list is a full Path Name of the
ExecutionUnit Object instance, including its Instance Identifier. The Path
Name MUST end with a “.” (dot) after the Instance Identifier of the Object.
In the case of an Install, this will be the list of EUs that were created as a
result of the DU’s installation.
In the case an Update, this will be the list of all EUs currently associated
with the updated DU, including those that were created through the initial
DU installation and any updates that had already occurred but not
including any EUs that no longer exist on the device because of this or
previous updates.
In the case of an Uninstall, this will be the list of the EUs removed from
the device due to the DU being removed.

November 2013 © The Broadband Forum. All rights reserved. Page 124 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Name Type Description

StartTime dateTime The date and time the operation on the DU was started in UTC. The CPE
SHOULD record this information and report it in this argument, but if this
information is not available, the value of this argument MUST be set to the
Unknown Time value, as defined in Section 3.2 / TR-106 [13].
CompleteTime dateTime The date and time the operation on the DU was fully completed and
applied in UTC. The CPE SHOULD record this information and report it in
this argument, but if this information is not available, the value of this
argument MUST be set to the Unknown Time value, as defined in Section
3.2 / TR-106 [13].
Fault FaultStruct A FaultStruct as defined in Table 81. If the operation was successful, the
FaultCode MUST be zero. Otherwise a non-zero FaultCode is specified
along with a FaultString indicating the failure reason.

Table 81 – FaultStruct Definition

Name Type Description
FaultCode unsignedInt The numerical fault code as defined in Section A.5.1. In the case of a fault, allowed
values are: 9001, 9003, 9012, 9013, 9015, 9016, 9017, 9018, 9022, 9023, 9024, 9025,
9026, 9027, 9028, 9029, 9030, 9031 and 9032.
A value of 0 (zero) indicates no fault.
FaultString string(256) A human-readable text description of the fault. This field SHOULD be empty if the
FaultCode equals 0 (zero).

Appendix II.5 / TR-157 Amendment 3 [29] provides a description of the Software

Module Management faults. The following error conditions are some examples of how a
CPE could fail a specific operation:
 If the CPE cannot complete the operation for some unknown reason, it SHOULD
reject the operation with a 9001 (Request Denied) fault code.
 If the CPE detects the presence of the “userinfo” component in the file source
URL, it SHOULD reject the operation with a 9003 (Invalid Arguments) fault
code.
 If the CPE cannot find the Execution Environment specified in the Install
operation, it SHOULD reject the operation with a 9023 (Unknown Execution
Environment) fault code.
 If the CPE determines that the Deployment Unit being installed does not match
either the Execution Environment specified or any Execution Environment on the
device, it SHOULD reject the operation with a 9025 (Deployment Unit to
Execution Environment Mismatch) fault code
 If the CPE determines that the Deployment Unit being updated does not match the
type of Execution Environment that it was previously installed against, it
SHOULD reject the operation with a 9025 (Deployment Unit to Execution
Environment Mismatch) fault code.
 If the CPE detects that the Deployment Unit being installed already has the same
version as one already installed on the same Execution Environment, it SHOULD
reject the operation with a 9026 (Duplicate Deployment Unit) fault code.

November 2013 © The Broadband Forum. All rights reserved. Page 125 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

 If the CPE detects that that there are no more system resources (disk space,
memory, etc.) to perform the Install or Update of a Deployment Unit, it SHOULD
reject the operation with a 9027 (System Resources Exceeded) fault code.
 If the CPE cannot find the Deployment Unit specified in the Update operation, it
SHOULD reject the operation with a 9028 (Unknown Deployment Unit) fault
code.
 If a requested operation attempts to alter the State of a Deployment Unit in a
manner that conflicts with the Deployment Unit State Machine Diagram
(Appendix II / TR-157 Amendment 3 [29]), the CPE SHOULD reject the
operation with a 9029 (Invalid Deployment Unit State) fault code.
 If a requested operation attempts to Uninstall a DU that caused an EE to come
into existence, where that EE has at least 1 installed DU or at least 1 child EE,
then the CPE SHOULD reject the operation with a 9029 (Invalid Deployment
Unit State) fault code.

Table 82 – DUStateChangeCompleteResponse Arguments

Argument Type Description
- void This method response has no arguments.

The following fault codes are defined for this method: 8000, 8001, 8002, 8003, 8004,
8005.

A.4.2.4 AutonomousDUStateChangeComplete
This method informs the ACS of the completion (successful or unsuccessful) of a DU
state change that was not specifically requested via CWMP using the ChangeDUState
RPC. When used, this method MUST be called only after the CPE has completed any file
transfers and carried out all operations related to the Autonomous DU State Change.
This method MAY contain the results from multiple autonomous DU state changes; it is
implementation specific how the CPE chooses to aggregate the autonomous DU state
changes, although the CPE MUST notify the ACS of any autonomous DU state changes
within 24 hours of the time the operations were completed by the CPE. The CPE
SHOULD make every attempt to aggregate, as much as possible, the autonomous change
notifications to the ACS in the interest of scalability.
If the ACS fails this method, the CPE MUST NOT regard the ACS as having been
informed of the completion of the file transfer, and MUST attempt to call the method
again, either in the current Session or in a new Session, subject to the event delivery rules
of Section 3.7.1.5.
The calling arguments for this method are defined in Table 83. The arguments in the
response are defined in Table 86.

November 2013 © The Broadband Forum. All rights reserved. Page 126 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Table 83 – AutonomousDUStateChangeComplete Arguments

Name Type Description
Results AutonOpResultStruct… The results of Autonomous Operations performed against
DUs.

Table 84 – AutonOpResultStruct Definition

Name Type Description
UUID string(36) The UUID as defined in RFC 4122 [34] of the DU that was affected by the
autonomous state change. In the case of an Install, this will be the UUID
of the DU that was created. In the case of an Update or Uninstall, it will
be the existing UUID of the DU that was either updated or uninstalled.
DeploymentUnitRef string(256) A reference to the DU affected by the autonomous state change. In the
case of an Install, this is the DU that was created. In the case of an
Update, this is the DU that was updated. In the case of an Uninstall, this
is the DU that was removed.
The DU reference is a full Path Name of the DeploymentUnit Object
instance, including its Instance Identifier. The Path Name MUST end with
a “.” (dot) after the Instance Identifier of the Object.
Version string(32) The version of the DU that was affected by the autonomous state change.
This MUST match the Version Parameter contained within the instance of
the DeploymentUnit that is contained within the DeploymentUnitRef
argument. In the case of an Install, this will be the version of the DU
created. In the case of an Update, it will be the updated version of the
DU. In the case of an Uninstall, it will be the version of the uninstalled DU
CurrentState string The current state of the affected DU. This state was attained either by
completing an autonomous Operation or reflects the state of the DU after
a failed attempt to autonomously change its state.
The following values are defined:
* Installed: The DU is in an Installed state due to one of the following:
successful Install, successful Update, failed Update, or failed Uninstall. In
the case of a failed Update or failed Uninstall the Fault argument will
contain an explanation of the failure.
* Uninstalled: The DU was successfully uninstalled from the device.
* Failed: The DU could not be installed in which case the DU instance
MUST NOT be created in the Data Model.
Resolved boolean Whether or not the autonomous DU operation resolved all of its
dependencies. In the case of an Uninstall, this value is meaningless and
SHOULD be true.
ExecutionUnitRefList string A comma-separated list of the Execution Units related to the affected DU.
Each Execution Unit (EU) in the list is a full Path Name of the
ExecutionUnit Object instance, including its Instance Identifier. The Path
Name MUST end with a “.” (dot) after the Instance Identifier of the Object.
In the case of an Install, this will be the list of EUs that were created as a
result of the DU’s installation.
In the case an Update, this will be the list of all EUs currently associated
with the updated DU, including those that were created through the initial
DU installation and any updates that had already occurred, but not
including any EUs that no longer exist on the device because of this or
previous updates.
In the case of an Uninstall, this will be the list of the EUs removed from
the device due to the DU Un-Installation.
StartTime dateTime The date and time the autonomous operation on the DU was started in
UTC. The CPE SHOULD record this information and report it in this
argument, but if this information is not available, the value of this
argument MUST be set to the Unknown Time value, as defined in Section
3.2 / TR-106 [13].

November 2013 © The Broadband Forum. All rights reserved. Page 127 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Name Type Description

CompleteTime dateTime The date and time the autonomous operation on the DU was fully
completed and applied in UTC. The CPE SHOULD record this
information and report it in this argument, but if this information is not
available, the value of this argument MUST be set to the Unknown Time
value, as defined in Section 3.2 / TR-106 [13].
Fault FaultStruct A FaultStruct as defined in Table 85. If the autonomous operation was
successful, the FaultCode MUST be zero. Otherwise a non-zero
FaultCode is specified along with a FaultString indicating the failure
reason.
OperationPerformed string The operation that was performed against the DU via the autonomous
state change. The following values are defined:
Install – The autonomous Operation attempted was the Installation of a
DU.
Update – The autonomous Operation attempted was the Update of an
existing DU.
Uninstall – The autonomous Operation attempted was the Un-Installation
of an existing DU.

Table 85 – FaultStruct Definition

Name Type Description
FaultCode unsignedInt The numerical fault code as defined in Section A.5.1. In the case of a fault, allowed
values are: 9001, 9003, 9012, 9013, 9015, 9016, 9017, 9018, 9022, 9023, 9024, 9025,
9026, 9027, 9028, 9029, 9030, 9031 and 9032.
A value of 0 (zero) indicates no fault.
FaultString string(256) A human-readable text description of the fault. This field SHOULD be empty if the
FaultCode equals 0 (zero).

Appendix II.5 / TR-157 Amendment 3 [29] provides a description of the Software

Module Management faults. The following error conditions are some examples of how a
CPE could fail a specific operation:
 If the CPE cannot complete the operation for some unknown reason, it SHOULD
reject the operation with a 9001 (Request Denied) fault code.
 If the CPE detects the presence of the “userinfo” component in the file source
URL, it SHOULD reject the operation with a 9003 (Invalid Arguments) fault
code.
 If the CPE cannot find the Execution Environment specified in the Install
operation, it SHOULD reject the operation with a 9023 (Unknown Execution
Environment) fault code.
 If the CPE determines that the Deployment Unit being installed does not match
either the Execution Environment specified or any Execution Environment on the
device, it SHOULD reject the operation with a 9025 (Deployment Unit to
Execution Environment Mismatch) fault code
 If the CPE determines that the Deployment Unit being updated does not match the
type of Execution Environment that it was previously installed against, it
SHOULD reject the operation with a 9025 (Deployment Unit to Execution
Environment Mismatch) fault code.

November 2013 © The Broadband Forum. All rights reserved. Page 128 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

 If the CPE detects that the Deployment Unit being installed already has the same
version as one already installed on the same Execution Environment, it SHOULD
reject the operation with a 9026 (Duplicate Deployment Unit) fault code.
 If the CPE detects that that there are no more system resources (disk space,
memory, etc.) to perform the Install or Update of a Deployment Unit, it SHOULD
reject the operation with a 9027 (System Resources Exceeded) fault code.
 If the CPE cannot find the Deployment Unit specified in the Update operation, it
SHOULD reject the operation with a 9028 (Unknown Deployment Unit) fault
code.
 If a requested operation attempts to alter the State of a Deployment Unit in a
manner that conflicts with the Deployment Unit State Machine Diagram
(Appendix II / TR-157 Amendment 3 [29]), the CPE SHOULD reject the
operation with a 9029 (Invalid Deployment Unit State) fault code.
 If a requested operation attempts to Uninstall a DU that caused an EE to come
into existence, where that EE has at least 1 installed DU or at least 1 child EE,
then the CPE SHOULD reject the operation with a 9029 (Invalid Deployment
Unit State) fault code.

Table 86 – AutonomousDUStateChangeCompleteResponse Arguments

Argument Type Description
- void This method response has no arguments.

The following fault codes are defined for this method: 8000, 8001, 8002, 8003, 8004,
8005.

A.5 Fault Handling

A.5.1 CPE Fault Codes
Table 87 lists the fault codes that can be returned by a CPE. Note that the fault code
values are shown in decimal representation.
Table 87 – Fault codes
24
Fault code Description Type
9000 Method not supported Server
9001 Request denied (no reason specified) Server
9002 Internal error Server
9003 Invalid arguments Client
9004 Resources exceeded (when used in association with SetParameterValues, this Server
MUST NOT be used to indicate Parameters in error)

24
The specified Type MUST be used to determine the value of the SOAP faultcode element as described in Section
3.4.7.

November 2013 © The Broadband Forum. All rights reserved. Page 129 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

24
Fault code Description Type
9005 Invalid Parameter name (associated with Set/GetParameterValues, Client
GetParameterNames, Set/GetParameterAttributes, AddObject, and DeleteObject)
9006 Invalid Parameter type (associated with SetParameterValues) Client
9007 Invalid Parameter value (associated with SetParameterValues) Client
9008 Attempt to set a non-writable Parameter (associated with SetParameterValues) Client
9009 Notification request rejected (associated with SetParameterAttributes method). Server
9010 File transfer failure (associated with Download, ScheduleDownload, Server
TransferComplete or AutonomousTransferComplete methods).
9011 Upload failure (associated with Upload, TransferComplete or AutonomousTrans- Server
ferComplete methods).
9012 File transfer server authentication failure (associated with Upload, Download, Server
TransferComplete, AutonomousTransferComplete, DUStateChangeComplete, or
AutonomousDUStateChangeComplete methods).
9013 Unsupported protocol for file transfer (associated with Upload, Download, Server
ScheduleDownload, DUStateChangeComplete, or
AutonomousDUStateChangeComplete methods).
9014 File transfer failure: unable to join multicast group (associated with Download, Server
TransferComplete or AutonomousTransferComplete methods).
9015 File transfer failure: unable to contact file server (associated with Download, Server
TransferComplete, AutonomousTransferComplete, DUStateChangeComplete, or
AutonomousDUStateChangeComplete methods).
9016 File transfer failure: unable to access file (associated with Download, Server
TransferComplete, AutonomousTransferComplete, DUStateChangeComplete, or
AutonomousDUStateChangeComplete methods).
9017 File transfer failure: unable to complete download (associated with Download, Server
TransferComplete, AutonomousTransferComplete, DUStateChangeComplete, or
AutonomousDUStateChangeComplete methods).
9018 File transfer failure: file corrupted or otherwise unusable (associated with Server
Download, TransferComplete, AutonomousTransferComplete,
DUStateChangeComplete, or AutonomousDUStateChangeComplete methods).
9019 File transfer failure: file authentication failure (associated with Download, Server
TransferComplete or AutonomousTransferComplete methods).
9020 File transfer failure: unable to complete download within specified time windows Client
(associated with TransferComplete method).
9021 Cancelation of file transfer not permitted in current transfer state (associated with Client
CancelTransfer method).
9022 Invalid UUID Format (associated with DUStateChangeComplete or Server
AutonomousDUStateChangeComplete methods: Install, Update, and Uninstall)
9023 Unknown Execution Environment (associated with DUStateChangeComplete or Server
AutonomousDUStateChangeComplete methods: Install only)
9024 Disabled Execution Environment (associated with DUStateChangeComplete or Server
AutonomousDUStateChangeComplete methods: Install, Update, and Uninstall)
9025 Deployment Unit to Execution Environment Mismatch (associated with Server
DUStateChangeComplete or AutonomousDUStateChangeComplete methods:
Install and Update)
9026 Duplicate Deployment Unit (associated with DUStateChangeComplete or Server
AutonomousDUStateChangeComplete methods: Install only)
9027 System Resources Exceeded (associated with DUStateChangeComplete or Server
AutonomousDUStateChangeComplete methods: Install and Update)
9028 Unknown Deployment Unit (associated with DUStateChangeComplete or Server
AutonomousDUStateChangeComplete methods: Update and Uninstall)
9029 Invalid Deployment Unit State (associated with DUStateChangeComplete or Server
AutonomousDUStateChangeComplete methods: Install, Update and Uninstall)

November 2013 © The Broadband Forum. All rights reserved. Page 130 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

24
Fault code Description Type
9030 Invalid Deployment Unit Update – Downgrade not permitted (associated with Server
DUStateChangeComplete or AutonomousDUStateChangeComplete methods:
Update only)
9031 Invalid Deployment Unit Update – Version not specified (associated with Server
DUStateChangeComplete or AutonomousDUStateChangeComplete methods:
Update only)
9032 Invalid Deployment Unit Update – Version already exists (associated with Server
DUStateChangeComplete or AutonomousDUStateChangeComplete methods:
Update only)
9800 – 9899 Vendor defined fault codes -

A.5.2 ACS Fault Codes

Table 88 lists the fault codes that can be returned by an ACS. Note that the fault code
values are shown in decimal representation.
Table 88 – Fault codes
24
Fault code Description Type
8000 Method not supported Server
8001 Request denied (no reason specified) Server
8002 Internal error Server
8003 Invalid arguments Client
8004 Resources exceeded Server
8005 Retry request Server
8006 ACS version incompatible with CPE Server
8800 – 8899 Vendor defined fault codes -

A.6 RPC Method XML Schema

The XML schema, which is the normative definition for all RPC methods defined for the
CPE WAN Management Protocol, is specified in the referenced files below:
Table 89 – CWMP XML Schema Versions
CWMP Namespace XSD
Version
1.0 urn:dslforum-org:cwmp-1-0 http://www.broadband-forum.org/cwmp.php/cwmp-1-0.xsd
1.1 urn:dslforum-org:cwmp-1-1 http://www.broadband-forum.org/cwmp.php/cwmp-1-1.xsd
1.2 urn:dslforum-org:cwmp-1-2 http://www.broadband-forum.org/cwmp.php/cwmp-1-2.xsd
1.3 urn:dslforum-org:cwmp-1-2 http://www.broadband-forum.org/cwmp.php/cwmp-1-3.xsd
1.4 urn:dslforum-org:cwmp-1-2 http://www.broadband-forum.org/cwmp.php/cwmp-1-4.xsd
1

November 2013 © The Broadband Forum. All rights reserved. Page 131 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Annex B. Removed

Annex Removed.

November 2013 © The Broadband Forum. All rights reserved. Page 132 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Annex C. Signed Vouchers

Note – the mechanism defined in this Annex is DEPRECATED in favor of the “Software Module
Management mechanism” as described in Appendix II / TR-157 Amendment 3 [29].

C.1 Overview
The CPE WAN Management Protocol defines an optional mechanism for securely
enabling or disabling optional CPE capabilities. Unlike Parameters, the Voucher
mechanism provides an additional layer of security for optional capabilities that require
secure tracking (such as those involving payment).
A Voucher is a digitally signed data structure that instructs a CPE to enable or disable a
set of Options. An Option is any optional capability of a CPE. When an Option is
enabled, the Voucher can specify various characteristics that determine under what
conditions that Option persists.

C.2 Control of Options Using Vouchers

An Option can be disabled, enabled, or enabled with expiration. An Option that is
enabled with no expiration stays enabled until the ACS explicitly disables it. An Option
that is enabled with expiration stays enabled only for the duration specified in the
Voucher. After the specified duration period, the CPE MUST disable the Option itself.
An Option can also be defined as either transferable or non-transferable. If not otherwise
specified, an Option enabled by a Voucher is non-transferable. A non-transferable
Option is automatically disabled if the CPE becomes associated with a different
broadband service provider than was in use at the time the Option was enabled. A
transferable Option is one that is maintained with the CPE regardless of any subsequent
changes of service provider.
Each Voucher, which can contain instructions to enable or disable one or more Options,
MUST be digitally signed using the XML-Signature format [15]. Before applying the
instructions in the Voucher, a CPE MUST validate the signature and authenticate the
signer.
A Voucher is specific to a single CPE and cannot be used on a CPE other than the one
indicated in the Voucher. This ensures that the mechanism used to distribute Vouchers
can be used to ensure that only those CPEs that have properly appropriated an Option can
enabled that Option.
A CPE supporting the use of Vouchers MUST support a network time synchronization
protocol such as NTP or SNTP to ensure access to accurate time and date information.
Application of a received voucher by the CPE, or comparison of an existing voucher

November 2013 © The Broadband Forum. All rights reserved. Page 133 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

against its expiration date, SHOULD only occur once the CPE has established network
time.
The following Voucher-related methods are defined in Annex A of this specification:
 SetVouchers: Allows an ACS to download a list of Vouchers to a CPE. Each
Voucher MAY enable or disable the Options defined within that Voucher.
 GetOptions: Allows an ACS to query the state of any or all Options supported by the
CPE.

C.3 Voucher Definition

The RPC method SetVouchers allows an ACS to enable, disable, or modify the state of
one or more Options. The SetVouchers method takes as an argument an array of
Vouchers. Each Voucher in the array is separately Base64 encoded.
Prior to Base64 encoding, each Voucher is a signed XML structure utilizing the XML-
Signature format [15]. Each independently signed Voucher MAY include one or more
Option specifications. Each Option specification is a structure that specifies the intended
state for the specified Option.
The elements of the Option specification are defined in Table 90. An Option MAY
contain additional XML elements specific to the particular Option. An example Option
specification structure is shown in Figure 4. An example of an entire signed Voucher is
shown in Figure 5. In this example, two separate Options are enabled in the same
Voucher.
Table 90 – Option specification definition
Name Type Description
VSerialNum string(64) Unique serial number identifying the particular Voucher. For a given
ACS, each new Voucher created MUST be assigned a distinct
Voucher serial number. This value MUST be unique across all CPE
managed by that ACS and all Vouchers issued to a given CPE at
different times.
DeviceId DeviceIdStruct A structure that uniquely identifies the particular CPE for which the
Voucher is to apply. This structure is defined in Table 91.
On receipt of a Voucher, a CPE MUST ensure that the information in
the device ID matches its actual identity. If not, it MUST ignore the
Voucher and respond with a Request Denied fault.
OptionIdent string(64) Identifying name of the particular Option to be enabled or disabled.
OptionDesc string(256) Text description of the Option.
StartDate dateTime Optional element. The date and time in UTC that the Option is to be
enabled (only meaningful if Mode = EnableWithExpiration or
EnableWithoutExpiration). If this element is not present, or if the
specified time has already passed, an Option to be enabled is
enabled immediately.
Duration unsignedInt Required if Mode = EnableWithExpiration. For an Option enabled
with expiration, this element specifies the duration the Option will
remain enabled in units of DurationUnits. If a start date is specified,
the duration is relative to that start date.
DurationUnits string Required if Mode = EnableWithExpiration. This element specifies the
units in which the duration element is specified. The allowed values
are:
“Days”
“Months”

November 2013 © The Broadband Forum. All rights reserved. Page 134 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Name Type Description

Mode string This element specifies whether the designated Option is to be
enabled or disabled, and if enabled, whether or not an expiration is
specified. The allowed values are:
“Disable”
“EnableWithExpiration
“EnableWithoutExpiration
Transferable boolean Optional element. A value of true (1) indicates that the Option is
considered transferable, meaning that Option is to remain enabled
until any specified expiration date regardless of any changes in
service provider.
If this element is false (0) or not present, the Option is considered
non-transferable, requiring the Option be disabled upon change in
service provider, associated with any change to the ProvisioningCode
as defined in [24], [31], and [32].

Table 91 – DeviceIdStruct definition

Name Type Description
Manufacturer string(64) The manufacturer of the device. This parameter is for display only and
need not be checked as part of the validation.
OUI string(6) Organizationally unique identifier of the device manufacturer. Represented
as a six hexadecimal-digit value using all upper-case letters and including
any leading zeros. The value MUST be a valid OUI as defined in [10].
ProductClass string(64) Identifier of the class of product for which the serial number applies. That
is, for a given manufacturer, this parameter is used to identify the product
or class of product over which the SerialNumber parameter is unique.
SerialNumber string(64) Identifier of the particular device that is unique for the indicated class of
product and manufacturer.

Figure 4 – Example Option specification

<dsig:Object xmlns="" xmlns:dsig="http://www.w3.org/2000/09/xmldsig#" Id="option0">
<Option>
<VSerialNum>987654321</VSerialNum>
<DeviceId>
<Manufacturer>Example</Manufacturer>
<OUI>012345</OUI>
<ProductClass>Gateway</ProductClass>
<SerialNumber>123456789</SerialNumber>
</DeviceId>
<OptionIdent>Option Name</OptionIdent>
<OptionDesc>Option Description</OptionDesc>
<StartDate>20021025T12:06:34</StartDate>
<Duration>280</Duration>
<DurationUnits>Days</DurationUnits>
<Mode>EnableWithExpiration</Mode>
</Option>
</dsig:Object>

Figure 5 – Example signed Voucher

<Signature xmlns="http://www.w3.org/2000/09/xmldsig#">
<SignedInfo>
<CanonicalizationMethod Algorithm="http://www.w3.org/TR/2001/REC-xml-c14n-
20010315"></CanonicalizationMethod>
<SignatureMethod Algorithm="http://www.w3.org/2000/09/xmldsig#dsa-
sha1"></SignatureMethod>
<Reference URI="#option0">
<Transforms>
<Transform Algorithm="http://www.w3.org/TR/2001/REC-xml-c14n-
20010315"></Transform>

November 2013 © The Broadband Forum. All rights reserved. Page 135 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

</Transforms>
<DigestMethod Algorithm="http://www.w3.org/2000/09/xmldsig#sha1"></DigestMethod>
<DigestValue>TUuSqr2utLtQM5tY2DB1jL3nV00=</DigestValue>
</Reference>
<Reference URI="#option1">
<Transforms>
<Transform Algorithm="http://www.w3.org/TR/2001/REC-xml-c14n-
20010315"></Transform>
</Transforms>
<DigestMethod Algorithm="http://www.w3.org/2000/09/xmldsig#sha1"></DigestMethod>
<DigestValue>/YX1C/E6zNf0+w4lG66NeXGOQB0=</DigestValue>
</Reference>
</SignedInfo>
<SignatureValue>
KAMfqOSnmGH52qRVGLNFEEM4PPkRSmMUGr2D8E3vwwW280e1Bn5pwQ==
</SignatureValue>
<KeyInfo>
<KeyValue>
<DSAKeyValue>
<P>
/X9TgR11EilS30qcLuzk5/YRt1I870QAwx4/gLZRJmlFXUAiUftZPY1Y+r/F9bow9s
ubVWzXgTuAHTRv8mZgt2uZUKWkn5/oBHsQIsJPu6nX/rfGG/g7V+fGqKYVDwT7g/bT
xR7DAjVUE1oWkTL2dfOuK2HXKu/yIgMZndFIAcc=
</P>
<Q>l2BQjxUjC8yykrmCouuEC/BYHPU=</Q>
<G>
9+GghdabPd7LvKtcNrhXuXmUr7v6OuqC+VdMCz0HgmdRWVeOutRZT+ZxBxCBgLRJFn
Ej6EwoFhO3zwkyjMim4TwWeotUfI0o4KOuHiuzpnWRbqN/C/ohNWLx+2J6ASQ7zKTx
vqhRkImog9/hWuWfBpKLZl6Ae1UlZAFMO/7PSSo=
</G>
<Y>
TBASA/mjLI8bc2KM7u9X6nHHvjmPgZtTBhr1/Fzs2AkdYCYMwyy+v+OXU7u5e18JuK
G7/uolVhjXNSn6ZgObF+wuMoyP/OUmNbSkdN1aRXXHPRsW2CcG3vjfV+Csg/LP3zfD
xDkImsC8LuKXht/g4+nksA/3icRQXWagQJU9pUQ=
</Y>
</DSAKeyValue>
</KeyValue>
<X509Data>
<X509IssuerSerial>
<X509IssuerName>
[email protected],CN=Example,OU=CMS,O=Example,L=San\20Jose,
ST=California,C=US
</X509IssuerName>
<X509SerialNumber>4</X509SerialNumber>
</X509IssuerSerial>
<X509SubjectName>
CN=eng.bba.certs.example.com,OU=CMS,O=Example,L=San\20Jose,ST=CA,C=US
</X509SubjectName>
<X509Certificate>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</X509Certificate>
<X509Certificate>

November 2013 © The Broadband Forum. All rights reserved. Page 136 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5
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</X509Certificate>
</X509Data>
</KeyInfo>
<dsig:Object xmlns="" xmlns:dsig="http://www.w3.org/2000/09/xmldsig#" Id="option0">
<Option>
<VSerialNum>987654321</VSerialNum>
<DeviceId>
<Manufacturer>Example</Manufacturer>
<OUI>012345</OUI>
<ProductClass>Gateway</ProductClass>
<SerialNumber>123456789</SerialNumber>
</DeviceId>
<OptionIdent>First option name</OptionIdent>
<OptionDesc>First option description</OptionDesc>
<StartDate>20021025T12:06:34</StartDate>
<Duration>280</Duration>
<DurationUnits>Days</DurationUnits>
<Mode>EnableWithExpiration</Mode>
</Option>
</dsig:Object>
<dsig:Object xmlns="" xmlns:dsig="http://www.w3.org/2000/09/xmldsig#" Id="option1">
<Option>
<VSserialNum>987654322</VSerialNum>
<DeviceId>
<Manufacturer>Example</Manufacturer>
<OUI>00D09E</OUI>
<ProductClass>Gateway</ProductClass>
<SerialNumber>123456789</SerialNumber>
</DeviceId>
<OptionIdent>Second option name</OptionIdent>
<OptionDesc>Second option description</OptionDesc>
<StartDate>20021025T12:06:34</StartDate>
<Duration>280</Duration>
<DurationUnits>Days</DurationUnits>
<Mode>EnableWithExpiration</Mode>
</Option>
</dsig:Object>
</Signature>

November 2013 © The Broadband Forum. All rights reserved. Page 137 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Annex D. Web Identity Management

Note–the mechanism defined in this Annex is DEPRECATED due to exploits like CSRF (cross-site
request forgery) and XSS (cross-site scripting), which turn the home network into an untrusted
environment. JavaScript downloaded from the Internet could allow a malicious script to perform
redirects and connect to a web site or portal with the “unknowing” subscriber web identity.

D.1 Overview
To support web-based applications or other CPE-related web pages on a back-end web
site for access from a browser within the CPE’s local network, the CPE WAN
Management Protocol provides an optional mechanism that allows such web sites to
customize their content with explicit knowledge of the customer associated with that
CPE. That is, the location of users browsing from inside the CPE’s LAN can be
automatically identified without any manual login process.
The protocol defines a set of optional interfaces that allow the web site to initiate
communication between the CPE and ACS, which allows a web site in communication
with that ACS to identify which CPE the user is operating behind. This allows the web
site to customize its content to be specific to the associated broadband account, the
particular type of CPE, or any other characteristic that is known to the ACS.
Note—this identification mechanism does not distinguish among different users on the same
network behind a single CPE. In situations where identification of a specific user is required, a
separate identity management mechanism, such as manual login, would be needed.

D.2 Use of the Kicked RPC Method

The CPE WAN Management Protocol defines an optional Kicked RPC method in Annex
A, which can be used to support web identity management functionality.
The CPE’s invocation of the Kicked method is initiated by an external stimulus to the
CPE. This external stimulus is assumed to be web-based, and thus the associated method
provides a means to communicate information that would be useful in a web-based
transaction. A suggested definition of the stimulus interface is given in Section D.4.
The information contained in the Kicked method call includes both the information
needed to uniquely identify the CPE, but also parameters that can be used to associate the
method call with a particular web browser session.
The response to the Kicked method allows the ACS to specify a URL to which the
browser SHOULD be redirected. This URL MAY contain CGI arguments that allow the
ACS to continue to track the browser session.

November 2013 © The Broadband Forum. All rights reserved. Page 138 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

D.3 Web Identity Management Procedures

The Web Identity Management mechanism is based on a model in which a web server is
associated with and can communicate with an ACS. Whenever this web server wishes to
either identify the user’s CPE or cause the CPE to establish communication with the ACS
for some other purpose, the following sequence of events will occur (under normal
conditions):
1. The user’s browser accesses a web page that requires knowledge of, or
communication with, the user’s CPE.
2. The web site redirects the browser to a specific URL accessible only from the CPE’s
private-network (LAN) interface through which the browser “kicks” the CPE,
providing the CPE via CGI arguments with information it needs to follow the
subsequent steps (see Section D.4).
3. The CPE notifies the ACS that it has been kicked, using the “Kicked” RPC method
call defined in Annex A. In this method call, the CPE identifies itself and passes
information to uniquely identify the browser session.
4. The ACS responds to this method call by passing a URL that the CPE SHOULD
redirect the user’s browser. This URL would normally include CGI arguments that
identify the session state. While the connection is open, the ACS MAY also initiate
any other appropriate RPC transactions.
5. The CPE responds to the browser’s HTTP request by redirecting the browser to the
URL indicated by the ACS.
This exchange allows the ACS to uniquely identify the CPE; potentially generate a
custom page based on knowledge of the particular user, their equipment, and any
associated account privileges; and then direct the user to that customized page.
The ACS MAY also initiate any other RPC transactions that are appropriate given the
particular user action. For example, if a user requests a firmware upgrade to their CPE
from a web page, the ACS could instruct the CPE to initiate a file download over the
same connection that the ACS responds to the Kicked method call.
Figure 6 shows the sequence of events associated with this mechanism. The numbers
shown correspond to the step numbers above.

November 2013 © The Broadband Forum. All rights reserved. Page 139 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Figure 6 – Sequence of events for the “kick” mechanism

Web Site
2

5
Access
Network
3
B-NT

ACS

D.4 LAN Side Interface

A CPE MAY support web identity management by providing a LAN-side web URL
accessible from a browser operating on the local network.
The associated web server in the CPE SHOULD support CGI arguments to be passed to
corresponding arguments in the Kicked RPC method defined in Annex A. The
RECOMMENDED arguments are listed in Table 92.
Table 92 – Recommended CGI Arguments for the kick URL
Name Type Value
command string(32) The value to be passed in the Command argument of the Kicked
method call. This CGI argument allows the ACS to identify a command
it is to perform in response to the resulting Kicked method call.
arg string(256) The value to be passed in the Arg argument of the Kicked method call.
This CGI argument MAY be used by the ACS to pass arguments for
the corresponding command. The particular uses for this argument are
not defined.
next string(1024) The value to be passed in the Next argument of the Kicked method
call. This contains the URL the web site wishes the browser be sent
after the Kicked process has completed. The ACS processing the
Kicked method MAY override this request and return a different URL in
the Kicked response.

To initiate the kick process, the browser would be sent to the CPE’s URL, for example
via an HTTP 302 redirect or via a form post. This access would include the CGI
arguments as defined in Table 92. For example, the browser might be redirected to:
http://cpe-host-
name/kick.html?command=<#>&arg=<arg>&next=<url>

November 2013 © The Broadband Forum. All rights reserved. Page 140 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

After the CPE receives the corresponding HTTP GET request, the CPE SHOULD initiate
a Kicked method call, using the CGI arguments to fill in the method arguments as
defined in Annex A.
The CPE SHOULD limit the number of Kicked method calls it sends to the ACS per hour
to a defined maximum value. Receiving a kick request that would result in exceeding
this maximum value is considered a security violation and SHOULD NOT result in a call
to the Kicked method.

November 2013 © The Broadband Forum. All rights reserved. Page 141 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Annex E. Signed Package Format

Note – the mechanism defined in this Annex is DEPRECATED in favor of the “Software Module
Management mechanism” as described in Appendix II / TR-157 Amendment 3 [29].

E.1 Introduction
This document specifies a signed package format that MAY be used to securely
download files into a recipient device. The format allows one or more files to be
encapsulated within a single signed package. The package format allows the recipient to
authenticate the source, and contains instructions for the recipient to extract and install
the contents.
The signed package format is intended to be used for download from a server via HTTP,
HTTPS, or FTP file transfer, or via other means of file transfer from a remote or local
source.

E.2 Signed Package Format Structure

The basic format of a signed package file is shown in Figure 7.
Figure 7 – Signed package format

Fixed length
Signatures
header

Command Payload
list files
A general description of each of the signed package format components is given in Table
93.
Table 93 – Signed package component summary
Component Description
Header The header is a fixed-length structure including a preamble, format version, and the lengths of
the command list and payload components.
Command list The command list contains a sequence of instructions to be followed in extracting and installing
the files contained within the package.
Each command is in the form of a type-length-value (TLV).
Signatures This section of the package contains a PKCS #7 digital signature block containing a set of zero
or more digital signatures as described in Section E.5.

November 2013 © The Broadband Forum. All rights reserved. Page 142 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Component Description
Payload files This section of the package contains one or more files to be installed following the instructions in
the command list.
This document does not define any specific payload file formats.

E.2.1 Encoding Conventions

The following encoding conventions are used throughout this specification unless
explicitly stated otherwise:
 Multi-octet numeric values are encoded in network byte order (big endian format).
 File or directory Path names are specified in UNIX format (e.g., “/dir/dir/base.ext”).

E.3 Header Format

The signed package header is a fixed-length 24-octet structure. The format of the header
is defined in Table 94.
Table 94 – Signed package header format
Field Type Description
Preamble 8 octets A fixed sequence of octets containing the following hexadecimal values:
32 57 49 52 45 5F 53 50
An interpreter of the signed package format MUST verify that the preamble
contains exactly this sequence of values for the package to be considered valid.
Major version 32-bit integer Value indicating the major component of the package format version. An
implementation conforming to this specification has a major version of 1 (one).
Changes to the major version denote incompatible changes to this format.
Minor version 32-bit integer Value indicating the minor component of the package format version. An
implementation conforming to this specification has a minor version of 0 (zero).
Changes to the minor version denote compatible changes to the package format.
An implementation implementing this version of the specification SHOULD be
capable of interpreting packages encoded using a format with a different minor
version value.
Command list 32-bit integer Length in octets of the command list. The command list length MUST be less
length than 216.
Payload 32-bit integer Length in octets of the payload, including all files contained within it.
length

E.4 Command List Format

Each command in the command list has a format specified in Table 95.
Table 95 – Command format
Field Type Description
Type 32-bit integer Specifies the particular command.
Length 32-bit integer Specifies the length in octets of the Value field. The total length of the command
is Length + 8 octets.
Value (Conditional) Zero or more octets of parameters associated with the particular command type.

If a recipient of this file format finds a Type value that is unknown to it, it MUST ignore
the command and continue parsing the remainder of the package, using the Length value
to skip to the next command, if any.

November 2013 © The Broadband Forum. All rights reserved. Page 143 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

E.4.1 Command Types

The command list contains two types of commands: package parameters and actions to
be taken. Examples of package parameters include the software version of a contained
software image or a timeout for the remainder of the download. Examples of actions are
add, remove, and move. The actions taken together in the order specified in the
command list define the sequence of modifications to the file system required to extract
and install the contained files.
The file-related commands have two variants: one that operates on explicit files and
another that operates on versioned files. The name of a versioned file has a fixed “base”
up to 8 characters in length, and an “extension” that is 3 characters in length. Each time
the content of a versioned file is updated, the file extension is changed to a new value that
indicates the file version. Because of this, if an upgrade needs to replace a versioned file,
any existing file with the same base name but different extension MUST be removed.
The specific commands defined by this specification are listed in Table 96.
Table 96 – Command Type summary
Type Command name
0 End
1 Extract File
2 Extract Versioned File
3 Add File
4 Add Versioned File
5 Remove File
6 Remove Versioned File
7 Remove Sub-Tree
8 Move File
9 Move Versioned File
10 Version
11 Description
12 Recoverable Timeout
13 Unrecoverable Timeout
14 Initial Timeout
15 Initial Activity Timeout
16 Reboot
17 Format File System
18 Minimum Version
19 Maximum Version
20 Role
21 Minimum Non-Volatile Storage
22 Minimum Volatile Storage Size
23 Reserved
24 Reserved
25 Required Attributes
1000- Vendor-specific commands
9999

November 2013 © The Broadband Forum. All rights reserved. Page 144 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

E.4.2 End Command

This command signifies the end of the command list. This command need not be present
in a command list, but if encountered a recipient MUST stop parsing the remainder of the
command list portion of the package.
The Length parameter for this command MUST be 0 (zero), indicating that no Value
field follows.

E.4.3 Extract and Add Commands

The extract and add commands include Extract File, Extract Versioned File, Add File,
and Add Versioned File.
The extract commands instruct the recipient to remove any existing file of the same name
and replace it with the specified file in the payload.
The add commands instruct the recipient to first check for an existing file of the same
name, and only install the new file if no existing file can be found.
For the versioned file variants of these commands, the above operations consider an
existing file as any file that has the same base name as the specified file. That is, the
Extract Versioned File command removes all existing files with the same base name and
any extension prior to installing the new file. Similarly, the Add Versioned File
command checks for any file with the same base name as the specified file, regardless of
extension, and only installs the new file if no such file can be found.
When a new file is to be created in a directory that does not exist, the recipient MUST
create the required directory.
All of the extract and add commands include information in the Value portion of the
command. The format of this information is defined in Table 97.
Table 97 – Value format for the extract and add commands
Field Type Description
Flags 32-bit integer A bit-field defined as follows:
Bit 0 (LSB): Unsafe Flag. A 1 (one) value of this flag indicates that if this
command completes successfully, but a subsequent command in the
command list fails, the recipient device will be left in an unsafe state, and
SHOULD follow its procedures for recovery of its file system to a known
safe state.
All other bits are reserved and MUST be set to 0 (zero) and MUST be ignored by
the recipient.
Path Offset 32-bit integer The offset in octets from the beginning of the Value field to the Path field in this
command.
Path Length 32-bit integer The length of the Path field in octets.
Hash Type 32-bit integer Type of hash algorithm used in creating the Hash field. The following values are
currently defined:
1 = SHA-1. When set to this value, the Hash field contains the 20-octet SHA-1
hash of the specified file. The Hash Length value in this case MUST be set to 20
(decimal).
All other values are reserved.
Hash Offset 32-bit integer The offset in octets from the beginning of the Value field to the Hash field in this
command.
Hash Length 32-bit integer The length of the Hash field in octets.
File Offset 32-bit integer The offset in octets from the beginning of the payload portion of the package to
the beginning of the specified file.

November 2013 © The Broadband Forum. All rights reserved. Page 145 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Field Type Description

File Length 32-bit integer The length of the file payload in octets. The actual contents of the file are found
in the file payload portion of the package.
Path String of length Path of the specified file, including the directory tree and file name.
Path Length
Hash Octet string of Hash of the payload file using the hash algorithm defined in the Hash Type field.
length Hash The hash of the payload file is included in the command because the signatures
Length validate only the package header and command list. By including the file hash in
the command, the signature ensures the validity of the file contents.

E.4.4 Remove Commands

The remove commands include Remove File, Remove Versioned File, and Remove Sub-
Tree.
The Remove File command removes the file with the specified path, if it exists.
The Remove Versioned File command removes all files with the same base as the
specified file, regardless of extension.
The Remove Sub-Tree command removes all files and directories beneath and including
the specified path.
All of the remove commands include information in the Value portion of the command.
The format of this information is defined in Table 98.
Table 98 – Value format for the remove commands
Field Type Description
Flags 32-bit integer A bit-field defined as follows:
Bit 0 (LSB): Unsafe Flag. A 1 (one) value of this flag indicates that if this
command completes successfully, but a subsequent command in the
command list fails, the recipient device will be left in an unsafe state, and
SHOULD follow its procedures for recovery of its file system to a known
safe state.
All other bits are reserved and MUST be set to 0 (zero) and MUST be ignored by
the recipient.
Path Offset 32-bit integer The offset in octets from the beginning of the Value field to the Path field in this
command.
Path Length 32-bit integer The length of the Path field in octets.
Path String of length Path of the specified file or directory.
Path Length

E.4.5 Move Commands

The move commands include Move File and Move Versioned File.
The Move File command renames a file to the name specified in this command. If the
destination path specified indicates a different directory, the file is moved to the indicated
destination directory.
The Move Versioned File command moves a file matching the base name of the file
specified in the source path, regardless of the extension. If more than one such file exists
in the specified directory, only one of the files is moved and the others are deleted. If the
versioned file extension string is a decimal number, then the lowest numbered file is
moved and the rest are deleted.

November 2013 © The Broadband Forum. All rights reserved. Page 146 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

In all cases, if there is already a file with the same path as the specified destination file,
the move commands will overwrite that file.
If the source file specified in a move command does not exist, no action is taken, and the
recipient continues to process the remaining commands in the command list.
All of the move commands include information in the Value portion of the command.
The format of this information is defined in Table 99.
Table 99 – Value format for the move commands
Field Type Description
Flags 32-bit integer A bit-field defined as follows:
Bit 0 (LSB): Unsafe Flag. A 1 (one) value of this flag indicates that if this
command completes successfully, but a subsequent command in the
command list fails, the recipient device will be left in an unsafe state, and
SHOULD follow its procedures for recovery of its file system to a known
safe state.
All other bits are reserved and MUST be set to 0 (zero) and MUST be ignored by
the recipient.
Source Path 32-bit integer The offset in octets from the beginning of the Value field to the Source Path field
Offset in this command.
Source Path 32-bit integer The length of the Source Path field in octets.
Length
Destination 32-bit integer The offset in octets from the beginning of the Value field to the Destination Path
Path Offset field in this command.
Destination 32-bit integer The length of the Destination Path field in octets.
Path Length
Source Path String of length Path of the source file.
Source Path
Length
Destination String of length Path of the destination to which the source file is to be moved/renamed.
Path Destination Path
Length

E.4.6 Version and Description Commands

The Value field for both the Version and Description commands contain a single UTF-8
string to be used for informational, display, or logging purposes.
The Version field is intended to indicate the overall version associated with the package.
For example, if the package contains a software upgrade (which can include many
individual files), the Version field MAY be used to indicate the new software version
associated with the upgrade.

E.4.7 Timeout Commands

The timeout commands include Initial Timeout, Initial Activity Timeout, Recoverable
Timeout, and Unrecoverable Timeout.
The timeout commands specify a timeout value for the continued download of the
package file before the download SHOULD be terminated. These commands are to
accommodate the case where the command and signature portions of the package are
downloaded and interpreted prior to downloading the remainder of the package file. The
timeout commands MAY be used to control the timeout parameters associated with a

November 2013 © The Broadband Forum. All rights reserved. Page 147 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

download process of this type. If the package is downloaded or received as a whole prior
to interpreting the package contents, the timeout commands MAY be ignored.
Each timeout command includes information in the Value portion of the command. The
format of this information is defined in Table 100.
Table 100 – Value format for the timeout commands
Field Type Description
Timeout 32-bit Integer The timeout value in seconds relative to the beginning of the package download
operation. A value of 0 (zero) indicates an infinite timeout.

Each of the timeout commands allows a distinct timeout value to be specified, where the
Timeout field in that command indicates the desired value. The use of each timeout
value is based on the state of the recipient as it processes commands using the state
transition model shown in Figure 8. The figure shows the state transitions that occur as
each command in the command list is processed in sequence. For each command
processed, the state remains the same until one of the cases indicated by the state
transition arrows occurs.
Figure 8 – Download state diagram used for timeout model

Recoverable
State End
Remove command
w/ Unsafe flag = 0

Start
download End
Initial State Install complete

Extract, Add, Move, or Remove

w/ Unsafe flag = 1
OR Format File System

End
Unrecoverable
Extract, Add, Move, or Remove State
w/ Unsafe flag = 1
OR Format File System

November 2013 © The Broadband Forum. All rights reserved. Page 148 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

The above state diagram is used during a download to determine which timeout values to
use. The definition of each of the timeout types associated with the timeout commands is
shown in Table 101.
Table 101 – Timeout command definitions
Command Description
Initial Timeout This command sets the download timeout used during the Initial State as shown in
Figure 8. This timeout is measured from the time the overall package download
began.
Initial Activity Timeout This command sets an activity timeout to be used only during the Initial State as
shown in Figure 8. The activity timeout is measured from the most recent time any
package data had been transferred to the recipient.
Note that during all states other than the Initial State, there is no activity timeout (the
activity timeout is infinite).
Recoverable Timeout This command sets the download timeout used during the Recoverable State as
shown in Figure 8. This timeout is measured from the time the overall package
download began.
Unrecoverable Timeout This command sets the download timeout used during the Unrecoverable State as
shown in Figure 8. This timeout is measured from the time the overall package
download began.

E.4.8 Reboot Command

This command indicates that the recipient reboot in order to complete the installation
process. If used, this command MUST be the last command in the command list (other
than End, if present).
The Length parameter for this command MUST be 0 (zero), indicating that no Value
field follows.

E.4.9 Format File System

This command indicates that the recipient reformat its file system as part of the
installation process. If used, this command implies that all existing files in the file
system (or the portion of the file system relevant for the installation process) are to be
cleared and overwritten by the new files in the package.
The Length parameter for this command MUST be 0 (zero), indicating that no Value
field follows.

E.4.10 Minimum and Maximum Version Commands

The Minimum Version and Maximum Version commands are used to specify the range
of software version numbers for which the package is intended to apply.
When a minimum and/or maximum version number is specified in the package using
these commands, the recipient MUST NOT install the files or take any other action
specified in the command list if the software version of the recipient falls outside the
indicated range.
This command MAY be used only if the format of the actual software version associated
with the recipient is in a hierarchical format that can be compared numerically given the
procedures outlined below.

November 2013 © The Broadband Forum. All rights reserved. Page 149 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

The minimum and maximum version commands include information in the Value portion
of the command. The format of this information is defined in Table 102.
Table 102 – Value format for the minimum and maximum version commands
Field Type Description
Version Array of 32-bit An array of integer elements indicating the version number. This is considered a
integers hierarchical version number (e.g., “1.0.20.3”), where each successive integer
represents a more minor element of the version number.

The following procedure is used to determine if a version is within the indicated range.
If a Minimum Version is given, then for each element of the Version array, beginning
with the first (most major element):
1. If this element of the recipient’s actual version is greater than the corresponding
element of the minimum version, then the recipient’s version meets the
requirement and the procedure is complete.
2. If this element of the recipient’s actual version number is less than the
corresponding element of the minimum version, then the recipient’s version does
not meet the requirement. In this case, the procedure is complete and the recipient
MUST NOT install the files in this package or follow any of the remaining
commands.
3. Otherwise (the values are equal),
a. If this is the last element in the array, then the recipient’s version meets
the requirement and the procedure is complete.
b. Otherwise (more elements remain), the procedure SHOULD continue at
step 1 using the next element of the array.
If a Maximum Version is given, then for each element of the Version array, beginning
with the first (most major element):
1. If this element of the recipient’s actual version is less than the corresponding
element of the maximum version, then the recipient’s version meets the
requirement and the procedure is complete.
2. If this element of the recipient’s actual version number is greater than the
corresponding element of the maximum version, then the recipient’s version does
not meet the requirement. In this case, the procedure is complete and the recipient
MUST NOT install the files in this package or follow any of the remaining
commands.
3. Otherwise (the values are equal),
a. If this is the last element in the array, then the recipient’s version meets
the requirement and the procedure is complete.
b. Otherwise (more elements remain), the procedure SHOULD continue at
step 1 using the next element of the array.

November 2013 © The Broadband Forum. All rights reserved. Page 150 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

E.4.11 Role Command

The role command is used to indicate the target application or purpose of the package.
This is intended to indicate any side effects or post-processing that might be required for
a particular package.
The role commands include information in the Value portion of the command. The
format of this information is defined in Table 103.
Table 103 – Value format for the role command
Field Type Description
Role 32-bit integer An enumeration indicating the target application or purpose of the package. The
following values are defined:
1 = Software upgrade
2 = Software recovery
3 = Web content
4 = Vendor configuration
5 = Tone file (see [25] Appendix B)
6 = Ringer file (see [25] Appendix B)
Values with 0xFF as their most significant octet are to be interpreted as a
vendor-specific Role. In this case, the subsequent three octets contain the OUI
(organizationally unique identifier) identifying the vendor as defined in [10].
When this value is used, the vendor MAY define subsequent additional
arguments to be included in this command in order to specifically identify the
role. Any additional arguments are to be interpreted in a vendor-specific
manner.
All other values are reserved.

E.4.12 Minimum Storage Commands

The minimum storage commands include Minimum Volatile Storage Size and Minimum
Non-Volatile Storage Size.
The minimum storage commands indicate the minimum requirement of the recipient
device to be able to install the files contained in the package. If present, each command
indicates the minimum requirement for the type of storage indicated by the command
name.
If the recipient device does not meet a specified minimum requirement, the recipient
MUST NOT install any of the files in the package or continue processing commands.
The minimum storage commands include information in the Value portion of the
command. The format of this information is defined in Table 104.
Table 104 – Value format for the minimum storage commands
Field Type Description
Storage Size 32-bit Integer The minimum required storage in bytes of the type indicated by the command.

E.4.13 Required Attributes Command

The Required Attributes command is used to specify additional attributes of the recipient
device that are required in order for the package to be considered valid for installation.
One or more Required Attributes commands MAY be included in a single package, each
indicating a different class of attributes required.

November 2013 © The Broadband Forum. All rights reserved. Page 151 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

The Required Attribute command includes information in the Value portion of the
command. The format of this information is defined in Table 105.
Table 105 – Value format for the required attributes command
Field Type Description
Defining Entity 32-bit Integer Identifier indicating the definer of the Class and Attribute values used in this
command. The following values are defined:
A value of 0 (zero) indicates standard Class and Attribute definitions. Standard
definitions are those defined by this version or future versions of this
specification.
Values with 0xFF as their most significant octet indicate vendor-specific Class
and Attribute definitions. In this case, the subsequent three octets contain the
OUI (organizationally unique identifier) identifying the vendor as defined in [10].
If a recipient processes a Required Attributes command with a defining entity
value that it does not recognize, it SHOULD ignore the command and continue
processing subsequent commands.
Class 32-bit Integer An enumeration indicating the criterion for which the recipient is to be compared
to determine whether or not this package is appropriate for that device. For a
given criterion, the attribute array field indicates the particular allowed values
associated with that criterion.
In this version of the specification, no standard class values are defined. For
vendor-specific defining entities, the interpretation of class values is vendor-
specific.
If a recipient processes a Required Attributes command with a class value that it
does not recognize, it SHOULD ignore the command and continue processing
subsequent commands.
Attribute Array Array of 32-bit A variable-length array attribute, where each attribute is an enumeration of a
Integer particular allowed value for the particular class.
If actual value associated with the recipient device matches any of the values
listed in this array, then the recipient meets the specified requirement.
Otherwise, the recipient does not meet the requirement and the package MUST
NOT be installed.
In this version of the specification, no standard attribute values are defined. For
vendor-specific defining entities, the interpretation of attribute values is vendor-
specific.

E.5 Signatures
The signature section immediately follows the command list section of the package file.
The signature section consists of a digital signature block using the PKCS #7 signature
syntax [16].
In particular, the signature block includes exactly one PKCS #7 SignedData Object,
which contains zero or more signatures with the following constraints:
 The signatures are “external signatures,” meaning that the signed message is not
encapsulated within the SignedData Object. Instead, the signed message data consists
of the octet string formed by the header and the command list components of the
package.
 The contentType element of the contentInfo MUST indicate type “data.”
 The content element of the contentInfo MUST be empty, since this is an external
signature and the message data resides outside the signature itself.
 The digestAlgorithm used for each signature MUST be of type SHA-1.
 The digestEncryptionAlgorithm used for each signature MUST be of type RSA.

November 2013 © The Broadband Forum. All rights reserved. Page 152 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

 The Tag value indicating the Identifier associated with the overall SignedData Object
MUST be less than or equal to 30, resulting in a single-octet encoding of the
Identifier.
 If there are no signatures in the signature block, there would be no extended
certificates or certificate revocation lists, the SignerInfo set would be empty, and the
digestAlgorithms set MAY be empty. All the other fields in SignedData MUST be
present as normal. Note that the content of an empty signature block is independent
of the content of the package and thus can be pre-computed as a fixed sequence of
bytes.
If the signature block contains more than one signature, at least one of the signatures
MUST be successfully validated for the recipient to consider the signed package as
trusted.
If one or more signatures are expected by the package recipient, the recipient MUST
validate the signature or signatures prior to processing the commands contained within
the command list. If none of the included signatures are validated, the recipient MUST
NOT process any of the commands in the command list or install any of the files
contained in the package.
If the recipient implementation is such that command list validation and processing might
be done without having loaded the entire package file from its source, the recipient MAY
assume that the combined length of the header, command list, and signature block is no
greater than 150 kilobytes.
Note that although the signed message data includes only the package header and
command list, the signature assures the integrity of the entire package because all
commands that refer to payload files include a hash of the file contents.
Note also that additional signatures can be added to an existing signed package file
without modifying any part of the file other than the signature block itself. The package
format is structured such that the other content (header, command list, and payload) of
the package file need not change if the length of the signature block changes.

November 2013 © The Broadband Forum. All rights reserved. Page 153 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Annex F. Device-Gateway
Association

F.1 Introduction
The CPE WAN Management Protocol can be used to remotely manage CPE Devices that
are connected via a LAN through a Gateway. When an ACS manages both a Device and
the Gateway through which the Device is connected, it can be useful for the ACS to be
able to determine the identity of that particular Gateway.
The procedures defined in this Annex allow an ACS to determine the identity of the
Gateway through which a given Device is connected.
As an example of when this capability might be needed, an ACS establishing QoS for a
particular service might need to provision both the Device as well as the Gateway
through which that Device is connected. To do the latter, the ACS would need to
determine the identity of that particular Gateway.
The specific scenario that the defined mechanism is intended to accommodate is where
both the Gateway and Device are managed via the CPE WAN Management Protocol, and
both are managed by the same ACS (or by distinct ACSs that are appropriately coupled).
Where a Device and Gateway are managed by independent ACSs, it is assumed that there
is no requirement for either ACS to be made aware of the Device-Gateway association.
The defined mechanism relies on the Device’s use of DHCP [20] / [35]. It is expected
that the vast majority of remotely manageable Devices will use DHCP, though not
necessarily all such Devices. While the mechanism defined here for Device-Gateway
association requires the use of DHCP, a Device using this mechanism need not use
DHCP for address allocation. This mechanism makes no assumptions about the address
allocated to the Device. That is, the Device might have a private or public IP address.

F.1.1 Terminology
The following terminology is used in this Annex.
Device CPE connected via local area network through a Gateway, bridge, or
router.
Device A three-tuple that uniquely identifies a Device, which includes the
Identity manufacturer OUI, serial number, and (optionally) product class.
Gateway Internet Gateway Device.
Gateway A three-tuple that uniquely identifies a Gateway, which includes the
Identity manufacturer OUI, serial number, and (optionally) product class.

November 2013 © The Broadband Forum. All rights reserved. Page 154 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

F.2 Procedures
The procedures for Device-Gateway association are summarized as follows:
 A Device following this Annex will pass its Device Identity to the Gateway via a
vendor-specific DHCP option. When the Gateway receives this information, it
populates a table containing identity information for each Device on its LAN. This
information is made available to the ACS via the ManageableDevice table in the
Gateway’s Data Model, defined in [24] and [32].
 In the DHCP responses, the Gateway provides the Device with its Gateway Identity,
which the Device makes available to the ACS via the GatewayInfo data Object
defined in [31] and [32]. The Device notifies the ACS of changes to the contents of
this Object. Thus a Device connecting to a previously unknown Gateway will result
in the ACS being notified of the Gateway Identity.
 To ensure the validity of this information, which is carried over an inherently insecure
DHCP exchange, the ACS validates the Gateway Identity provided by the Device by
crosschecking against the Device Identity provided by the Gateway.

F.2.1 Gateway Requirements

A Gateway conforming to this Annex MUST support the DeviceAssociation:2 profile as
defined in [24] or the DeviceAssociation:1 profile as defined in [32], depending on the
Root Data Model implemented.
A Gateway conforming to this Annex MUST inspect all DHCPv4 or DHCPv6 requests
received on a LAN interface and determine if the requesting Device has included its
Device Identity in the request. A DHCP request is determined to include the Device
Identity if it contains a DHCPv4 V-I Vendor-Specific Information Option (option number
125, as defined in [22]) or DHCPv6 Vendor-Specific Information Option (option number
17, as defined in [35]) that includes the Device Identity information, as defined in Section
F.2.5. The DHCPv4 requests for which this requirement applies are DHCPDISCOVER,
DHCPREQUEST, and DHCPINFORM. The DHCPv6 requests for which this
requirement applies are SOLICIT, REQUEST, RENEW, and INFORMATION-
REQUEST.
If the DHCP request is determined to include the Device Identity, then the Gateway
MUST do the following:
 The Gateway MUST include its Gateway Identity in all subsequent DHCP
responses. The Gateway Identity is carried in the DHCPv4 V-I Vendor-Specific
Information Option (option number 125, as defined in [22]) or DHCPv6 Vendor-
Specific Information Option (option number 17, as defined in [35]), as defined in
Section F.2.5. The DHCPv4 responses for which this requirement applies are
DHCPOFFER and DHCPACK. The DHCPv6 responses for which this
requirement applies are ADVERTISE and REPLY.
 On successful completion of the DHCP exchange, if an entry with a matching
Device Identity is not currently listed in the ManageableDevice table, then the
Gateway MUST add a new entry in its ManageableDevice table (see [24] and
[32]) that includes the Device Identity for this Device.

November 2013 © The Broadband Forum. All rights reserved. Page 155 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

The Gateway MUST adhere to the following additional requirements:

 The Gateway MUST retain a Device’s entry in the ManageableDevice table as
long as the Device remains actively connected to the Gateway’s LAN.
 The Gateway MUST remove a Device’s entry when either:
o The DHCP-supplied information becomes invalid, e.g. the DHCPv4 lease
expires or is released.
o The Gateway determines that the Device is no longer actively connected to
the Gateway’s LAN using a locally defined means of connectivity detection.
 The Gateway MUST allow the ACS to request Active notification on additions
or deletions to the ManageableDevice table. If the ACS has set the Notification
Attribute for the Parameter ManagementServer.ManageableDeviceNumberOf-
Entries to Active notification, then the Gateway MUST notify it each time a
Device entry is added or removed using the Notification mechanism defined by
the CPE WAN Management Protocol. If Active notification is enabled for this
Parameter, the Gateway MUST limit the frequency of Active notification
resulting from changes to the number of entries in the ManageableDevice table
as specified by the value of the ManageableDeviceNotificationLimit Parameter
in the same Object.

F.2.2 Device Requirements

A Device conforming to this Annex MUST support the GatewayInfo:1 profile as defined
in [31] and [32].
A Device conforming to this Annex MUST do the following:
 In DHCP requests, the Device MUST include a DHCPv4 V-I Vendor-Specific
Information Option (option number 125, as defined in [22]) or DHCPv6 Vendor-
Specific Information Option (option number 17, as defined in [35]) that includes
its Device Identity information, as defined in Section F.2.5. The DHCPv4
requests for which this requirement applies are DHCPDISCOVER,
DHCPREQUEST, and DHCPINFORM. The DHCPv6 requests for which this
requirement applies are SOLICIT, REQUEST, RENEW, and INFORMATION-
REQUEST.
 If the DHCP response includes the Gateway Identity carried in the DHCPv4 V-I
Vendor-Specific Information DHCP Option (option number 125, as defined in
[22]) or DHCPv6 Vendor-Specific Information Option (option number 17, as
defined in [35]), as defined in Section F.2.5, the Device MUST record the
received value in the GatewayInfo data Object defined in [31] and [32]. All of the
following values MUST be recorded:
Device.GatewayInfo.ManufacturerOUI
Device.GatewayInfo.SerialNumber
Device.GatewayInfo.ProductClass

November 2013 © The Broadband Forum. All rights reserved. Page 156 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

 The DHCPv4 responses for which this requirement applies are DHCPOFFER and
DHCPACK. The DHCPv6 response for which this requirement applies are
ADVERTISE and REPLY.
 If any of the elements of the Gateway Identity are not present in the V-I Vendor-
Specific Information DHCP Option, the Device MUST record an empty string for
each such item (replacing the previous value, if any).
 For all of the Parameters in the Device.GatewayInfo Object, the Device MUST by
default set the Notification attribute as defined in Annex A to Active notification.
The Device MUST apply this default whenever the URL of the ACS is set or
subsequently modified. Whenever Active notification is enabled for these
Parameters, the device MUST actively notify the ACS as defined in Annex A if
the value of any of these Parameters changes.
 If the DHCP-discovered information becomes invalid, e.g. the DHCPv4 lease is
released or expires without renewal, all entries in the GatewayInfo Object MUST
be discarded (set to the empty string).

F.2.3 ACS Requirements

Whenever a Device is associated with a Gateway, the Device will notify the ACS,
providing the new Gateway Identity information. When this occurs, the ACS SHOULD
do the following:
 If the ACS has previously associated the Device with a Gateway, the ACS
SHOULD examine the Gateway Identity from the Device (from the GatewayInfo
Object) and compare it to the Gateway Identity of the prior association. If the
association is unchanged, the ACS need not take any further action.
 If the Gateway Identity from the Device is different from the identity of the
Gateway previously associated with the Device, or if there was no previous
Gateway association for the Device, then the ACS SHOULD first validate the
information provided by the Device, and if validated, update the Device-Gateway
association to indicate the new Gateway Identity.
The ACS SHOULD consider the association valid only if all elements of the
Device Identity match the Device Identity elements in at least one entry in the
ManageableDevice table of the indicated Gateway (see [24] and [32]). The ACS
would determine the current contents of the ManageableDevice table either by
contacting the Gateway using a Connection Request to read the table, or receiving
Active notifications on additions and deletions to this table (by the ACS having
previously requested Active notifications on the ManageableDeviceNumberOf-
Entries Parameter).

November 2013 © The Broadband Forum. All rights reserved. Page 157 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

F.2.4 Device-Gateway Association Flows

Note – The examples in this Section are specific to DHCPv4. The flows for DHCPv6 would display the
same logic but with DHCPv4 messages replaced with the corresponding DHCPv6 messages.
Figure 9 shows the flow associated with the procedures for Device-Gateway association,
where the Device uses a DHCP Discover message to initiate the association as part of
DHCP address allocation.

Device Gateway ACS

DHCP Discover (device identity)

DHCP Offer (gateway identity)

DHCP Request (device identity)

Add device record to

ManageableDevice table

DHCP Ack (gateway identity)

TR-069 Inform (device + gateway identity)

TR-069 Inform Response

Establish TR-069 Session

Get ManageableDevice table (TR-069)

Optional
Cross-
Check
ManageableDevice table (TR-069)

Figure 9 – Device-Gateway Association using DHCP Discover

November 2013 © The Broadband Forum. All rights reserved. Page 158 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

The use of DHCP does not dictate that the device use DHCP for address allocation. If the
Device obtains IP addressing Parameters using other means, the device would use a
DHCP Inform for the exchange of information with the Gateway. The flow for this case
is show in Figure 10.

Device Gateway ACS

DHCP Inform (device identity)

Add device record to

ManageableDevice table

DHCP Ack (gateway identity)

TR-069 Inform (device + gateway identity)

TR-069 Inform Response

Establish TR-069 Session

Get ManageableDevice table (TR-069)

Optional
Cross-
Check
ManageableDevice table (TR-069)

Figure 10 – Device-Gateway Association Using DHCP Inform

F.2.5 DHCP Vendor Options

The Device Identity and Gateway Identity information exchanged via DHCP MUST be
contained within the DHCPv4 V-I Vendor-Specific Information Option (option number
125, as defined in [22]) or DHCPv6 Vendor-Specific Information Option (option number
17, as defined in [35]). These DHCP options are defined to allow vendor-specific
information from multiple distinct organizations, where the specific organization is
explicitly identified via an IANA Enterprise Number.
For DHCP messages that contain Device Identity or Gateway Identity information, the
Vendor-Specific Information DHCP Option MUST include an element identified with the
IANA Enterprise Number for the Broadband Forum that follows the format defined
below. The IANA Enterprise Number for the Broadband Forum is 3561 in decimal (the
“ADSL Forum” entry in the IANA Private Enterprise Numbers registry [18]).

November 2013 © The Broadband Forum. All rights reserved. Page 159 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Each vendor-specific element within this DHCP Option is defined to contain a series of
one or more Encapsulated Vendor-Specific Option-Data fields, encoded as specified in
[22] / [35]. Each such field includes a Sub-Option Code, a Sub-Option Length, and Sub-
Option Data. The values for these elements defined in this Annex are listed in Table 106.
Table 106 – Encapsulated Vendor-Specific Option-Data fields
25
Encapsulated Option Sub-Option Code Source Source Parameter
DHCPv4 DHCPv6 Entity
Option 125 Option 17
DeviceManufacturerOUI 1 11 Device Device.DeviceInfo.ManufacturerOUI26
DeviceSerialNumber 2 12 Device Device.DeviceInfo.SerialNumber26
DeviceProductClass 3 13 Device Device.DeviceInfo.ProductClass26
GatewayManufacturerOUI 4 14 Gateway DeviceInfo.ManufacturerOUI27
GatewaySerialNumber 5 15 Gateway DeviceInfo.SerialNumber27
GatewayProductClass 6 16 Gateway DeviceInfo.ProductClass27

Note – the DHCPv6 Option 17 Sub-Option Codes were changed in TR-069 Amendment 5
(previously they were 1-6) because they overlapped with the Section 3.1 ACS DHCP Discovery
Codes (1-4).
In encoding the source Parameter value in the corresponding Sub-Option Data element,
the resulting string MUST NOT be null terminated.
For a DHCP request from the Device that contains the Device Identity, the DHCP Option
MUST contain the following Encapsulated Vendor-Specific Option-Data fields:
 DeviceManufacturerOUI
 DeviceSerialNumber
 DeviceProductClass (this MAY be left out if the corresponding source Parameter
is not present)
For a DHCP response from the Gateway that contains the Gateway Identity, the DHCP
Option MUST contain the following Encapsulated Vendor-Specific Option-Data fields:
 GatewayManufacturerOUI
 GatewaySerialNumber
 GatewayProductClass (this MAY be left out if the corresponding source
Parameter is not present)

F.3 Security Considerations

While this Annex was designed to provide a high degree of security, some known
vulnerabilities remain:
 While the mechanism to allow the ACS to validate the identity information
provided to it by the Device is optional, it is strongly encouraged that this

25
The value of the corresponding Sub-Option Data element is obtained from the specified Parameter value.
26
As defined in [31] and [32].
27
As defined in [24] and [32].

November 2013 © The Broadband Forum. All rights reserved. Page 160 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

validation be implemented. The use of this validation is the only means within
the context of this Annex to overcome the lack of an inherent integrity checking
mechanism in the DHCP exchange between the Device and Gateway. By using
this validation, attempts to tamper with the identity information of either the
Device or Gateway can be detected by the ACS.
 The condition for validation of the Device-Gateway association is that the Device
can communicate over the LAN to the Gateway and that the Device and Gateway
can authenticate themselves via the CPE WAN Management Protocol to the ACS.
The possibility exists that a valid Device not present on a Gateway’s LAN could
falsify its association with a Gateway by providing a communication path
between the Device and the Gateway’s LAN. For example, a Device could
establish a communication path to a server, which in turn communicates with a
Trojan horse application on the target LAN, which acts as a proxy for the Device.
Providing such a path could make the Device indistinguishable from one
physically connected to the LAN. To mitigate this possibility, the Gateway can
optionally provide mechanisms to allow the user to monitor and regulate what
devices are present on the LAN.

November 2013 © The Broadband Forum. All rights reserved. Page 161 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Annex G. Connection Request via

NAT Gateway

Note – The mechanism defined in this Annex is OBSOLETED in favor of the “XMPP Connection
Request” mechanism defined in Annex K. This mechanism only works with “Classic STUN” as
defined in RFC 3489 [21], which has been made obsolete by the introduction of RFC 5389 [33]. This
mechanism was not designed to work with STUN as defined in RFC 5389. IPv6 deployments will
either not use NAT or will use it in different ways.

G.1 Introduction
The CPE WAN Management Protocol can be used to remotely manage CPE Devices that
are connected via a LAN through a Gateway. When an ACS manages a Device
connected via a NAT Gateway (where the Device has been allocated a private IP
address), the CPE WAN Management Protocol can still be used for management of the
Device, but with the limitation that the Connection Request mechanism defined in
Section 3.2.2 that allows the ACS to initiate a Session cannot be used.
The procedures defined in this Annex allow an ACS to initiate a Session with a device
that is operating behind a NAT Gateway. This provides the equivalent functionality of
the Connection Request defined in Section 3.2.2, but makes use of a different mechanism
to accommodate this scenario.
The mechanism defined in this Annex does not assume that the Gateway through which
the Device is connected supports the CPE WAN Management Protocol. This mechanism
requires support only in the Device and the associated ACS.

G.2 Procedures
To accommodate the ability for an ACS to issue the equivalent of a Connection Request
to CPE allocated a private address through a NAT Gateway that might not be CPE WAN
Management Protocol capable, the following is required:
 The CPE MUST be able to discover that its connection to the ACS is via a NAT
Gateway that has allocated a private IP address to the CPE.
 The CPE MUST be able to maintain an open NAT binding through which the
ACS can send unsolicited packets.
 The CPE MUST be able to determine the public IP address and port associated
with the open NAT binding, and communicate this information to the ACS.
To accomplish the above items, this Annex defines a particular use of the STUN
mechanism, defined in RFC 3489 [21].

November 2013 © The Broadband Forum. All rights reserved. Page 162 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

The use of STUN for this purpose requires that a new UDP-based Connection Request
mechanism be defined to augment the existing HTTP-based Connection Request
mechanism defined in Section 3.2.2.
The procedures for making use of STUN to allow the use of UDP Connection Requests
to a CPE are summarized as follows:
 The ACS enables the use of STUN in the CPE (if it is not already enabled by
factory default) and designates the STUN server for the CPE to use.
 The CPE uses STUN to determine whether or not the CPE is behind a NAT
Gateway with a private allocated address.
 If the CPE is behind a NAT Gateway with a private allocated address, the CPE
uses the procedures defined in STUN to discover the binding timeout.
 The CPE sends periodic STUN Binding Requests at a sufficient frequency to keep
alive the NAT binding on which it listens for UDP Connection Requests.
 When the CPE determines the public IP address and port for the NAT binding on
which it is listening for UDP Connection Requests, and whenever it subsequently
changes, the CPE communicates this information to the ACS. Two means are
provided by which the ACS, at its discretion, can obtain this information—either
from information provided in the STUN Binding Request messages themselves,
or via Notification on changes to the UDPConnectionRequestAddress Parameter,
which the CPE will update to include the public Connection Request address and
port.
 Whenever the ACS wishes to establish a connection to the CPE, it can send a
UDP Connection Request to the CPE. To accommodate the broadest class of
NAT Gateways, this will be sent from the same source address and port as the
STUN server.

G.2.1 CPE Requirements

A CPE conforming to this Annex MUST support the UDPConnReq :1 profile as defined
in [24] and [32] if the CPE is an Internet Gateway Device, or as defined in [31] and [32]
if the CPE is any other type of Device.
Whenever the STUNEnable Parameter in the ManagementServer Object is set to true,
CPE following the requirements of this Annex MUST make use of the procedures
defined in STUN [21] to determine whether or not address and/or port translation is
taking place between the CPE and the STUN server. If address and/or port translation is
taking place, the CPE MUST:
 Determine the public IP address and port for the NAT binding on which it is
listening for UDP Connection Request messages.
 Discover the NAT binding timeout, and send STUN Binding Request messages at
a rate necessary to keep alive this binding.
 Indicate via STUN optional attributes on which binding it is listening for UDP
Connection Requests, and if the binding has recently changed. Also, update the

November 2013 © The Broadband Forum. All rights reserved. Page 163 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

UDPConnectionRequestAddress Parameter to indicate the current public IP

address and port associated with the binding.
 Listen for UDP Connection Request messages, and act on these messages when
they arrive.
The details of each of these functions are defined in the following Sections.
Note – While the CPE requirements defined here certainly apply to a Device connected via LAN to a
Gateway, the same procedures can be followed by a Gateway, which might be operating behind a
network-based NAT gateway. Thus the requirements are defined generically for CPE, which might be
either a Device or Gateway.

G.2.1.1 Binding Discovery

When STUN is enabled via the STUNEnable Parameter in the ManagementServer
Object, the CPE MUST send Binding Request messages to the STUN server designated
in the STUNServerAddress and STUNServerPort Parameters, as defined in [21]. If no
STUNServerAddress is given, the address of the ACS determined from the host portion
of the ACS URL MUST be used as the STUN server address.
For the purpose of binding discovery, Binding Requests MUST be sent from the source
address and port on which the CPE will be listening for UDP Connection Requests if it
determines that address and/or port translation is in use (Binding Requests for binding
timeout discovery, will be sent from a different port as described in Section G.2.1.2).
The basic Binding Request message allows the CPE to determine if address and/or port
translation is in use between the CPE and the STUN server. This is determined by
comparing the source address and port on which the request was sent to the MAPPED-
ADDRESS attribute received in a response from the STUN server. If either the address
or port is different, then translation is in use.
If it is determined that address and/or port translation is in use, the CPE MUST record the
value of the MAPPED-ADDRESS attribute in the most recently received Binding
Response. This represents the public IP address and port to which UDP Connection
Requests would be sent.
Each time the CPE subsequently sends a Binding Request for the purpose of maintaining
the binding (see G.2.1.2), the CPE MUST again determine if address and/or port
translation is in use, and if so, obtain the public IP address and port information from the
MAPPED-ADDRESS attribute in a successful Binding Response. The actions the CPE
will take when this information changes are defined in Section G.2.1.3.
If the CPE has been provisioned with a STUNUsername and STUNPassword in the
ManagementServer Object, then if the CPE receives a Binding Error Response from the
STUN server with a fault code of 401 (Unauthorized), then the CPE MUST resend the
Binding Request with the USERNAME and MESSAGE-INTEGRITY attributes as
defined in [21]. Whenever a Binding Request is sent that includes the MESSAGE-
INTEGRITY attribute, the CPE MUST discard a corresponding Binding Response if the
MESSAGE-INTEGRITY attribute in the Binding Response is either invalid, as defined
in [21], or is not present.

November 2013 © The Broadband Forum. All rights reserved. Page 164 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

If the local IP address allocated to the CPE changes, the CPE MUST re-discover the
binding using the procedures described above. The minimum limit on the Binding
Request period defined by STUNMinimumKeepAlivePeriod does not apply in this case.
Other than Binding Request messages sent explicitly in response to a Binding Error
Response from the STUN server with a fault code of 401 (Unauthorized), the CPE
MUST NOT include the MESSAGE-INTEGRITY attributes in any Binding Request.28
The STUN client in the CPE need not support the CHANGE-REQUEST attribute of
STUN Binding Requests, nor need it understand the CHANGED-ADDRESS, SOURCE-
ADDRESS, and REFLECTED-FROM attributes present in a Binding Response.29
The STUN client in the CPE need not support the STUN messages for exchanging a
Shared Secret. None of these messages are used in the application defined in this Annex.

G.2.1.2 Maintaining the Binding

To keep alive the NAT binding, the CPE MUST periodically retransmit Binding Request
messages from the source address and port on which the CPE will be listening for UDP
Connection Requests.
The CPE MUST NOT send these Binding Requests more frequently than is specified by
the STUNMinimumKeepAlivePeriod Parameter in the ManagementServer Object.
The CPE MUST send these Binding Requests at least as frequently as is specified by the
STUNMaximumKeepAlivePeriod Parameter in the ManagementServer Object, if a value
is specified.
If the value of STUNMinimumKeepAlivePeriod and STUNMaximumKeepAlivePeriod
are not equal, then the CPE MUST actively discover the longest keep-alive period for
which the NAT binding is maintained. To do this, the CPE MUST use the procedures
described generally in [21] to learn the binding timeout. Specifically, the CPE MUST be
able to test whether the binding has timed out by sending Binding Requests from a
secondary source port distinct from the primary source port, and use the RESPONSE-
ADDRESS attribute in the Binding Request to indicate that the STUN Binding Response
be sent to the primary source port (the port on which the CPE is listening for UDP
Connection Request messages).
The specific procedures by which the CPE uses Binding Requests from the secondary
source port to determine the binding timeout is left to the discretion of the CPE vendor.
In general, the procedure would consist of two phases: a discovery phase, and a
monitoring phase. During the discovery phase, the CPE is attempting to learn the value
of the binding timeout, and would test different timeout values to determine the actual
timeout value (for example, using a binary search). During the monitoring phase, the
CPE would periodically test the binding prior to refreshing it to determine if the binding

28
Because the STUN specification requires the STUN server to use message integrity in its response if message
integrity was used in the request, the CPE cannot use message integrity for Binding Requests on its own, but only
when so directed by the STUN server. This is to ensure that the server has total discretion as to when and whether
message integrity is to be used.
29
These attributes are primarily intended to allow discovery of the type of NAT in use, which is not required for this
Annex.

November 2013 © The Broadband Forum. All rights reserved. Page 165 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

is still in place. If not, the CPE could then revert to the discovery phase to determine a
new value for the binding.
The minimum limit on the Binding Request period defined by STUNMinimumKeep-
AlivePeriod does not apply to Binding Requests sent from a secondary source port.

G.2.1.3 Communication of the Binding Information to the ACS

Two means are defined by which the ACS can be informed of the binding information.
The CPE MUST support both methods.30 The first method involves the use of optional
STUN attributes sent in the Binding Requests. The second method involves the CPE
updating the value of the UDPConnectionRequestAddress Parameter as the binding
information changes.
Table 107 specifies a set of STUN attributes are defined for this application. These use
Attribute Type values that are greater than 0x7FFF, which the STUN specification
defines as “optional.” STUN servers that do not understand optional attributes, are
required to ignore them.
Table 107 – Optional STUN attributes used in Binding Request messages
Attribute Type Name Description
0xC001 CONNECTION-REQUEST-BINDING Indicates the binding on which the CPE is listening for
UDP Connection Requests.
The content of the Value element of this attribute MUST
be the following byte string:
0x64 0x73 0x6C 0x66
0x6F 0x72 0x75 0x6D
0x2E 0x6F 0x72 0x67
0x2F 0x54 0x52 0x2D
0x31 0x31 0x31 0x20
This corresponds to the following text string:31
“dslforum.org/TR-111 ”
A space character is the last character of this string so
that its length is a multiple of four characters.
The Length element of this attribute MUST equal:
0x0014 (20 decimal)
0xC002 BINDING-CHANGE Indicates that the binding has changed.
This attribute contains no value. Its Length element
MUST be equal to zero.
This attribute MUST only be used where the
CONNECTION-REQUEST-BINDING is also included.

A CPE MUST include the CONNECTION-REQUEST-BINDING attribute in every

Binding Request message whose source address and port are the address and port on
which it is listening for UDP Connection Request messages. In all other Binding Request
messages, the CPE MUST NOT include this attribute.

30
Defining two methods allows flexibility by the ACS in making the tradeoffs between these two approaches.
Specifically, the STUN-based approach may require a tighter coupling between the ACS itself and the associated
STUN server, while the Notification-based approach may result in greater communication overhead.
31
This text string is used to allow an observer, including the NAT Gateway itself, to identify that these STUN
messages represent UDP Connection Request bindings associated with this specification. A Gateway might use
this knowledge to optimize the associated performance. For example, a Gateway could lengthen the UDP timeout
associated with this binding to reduce the frequency of binding updates.

November 2013 © The Broadband Forum. All rights reserved. Page 166 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

In every Binding Request message sent in which the CPE includes the CONNECTION-
REQUEST-BINDING attribute, if the value of the STUNUsername Parameter in the
ManagementServer Object is non-empty, the CPE MUST include the USERNAME
attribute set to the value of the STUNUsername Parameter, if necessary padded with
trailing spaces to make its length a multiple of 4 bytes (as required by the STUN
protocol).
Whenever the CPE detects a change to the NAT binding (as well as the first time the CPE
determines the binding), it MUST immediately send a Binding Request message from the
primary source port (the port on which the CPE is listening for UDP Connection Request
messages) that includes the BINDING-CHANGE attribute. This Binding Request MUST
NOT include the RESPONSE-ADDRESS or CHANGE-REQUEST attributes. In all
other Binding Request messages, the CPE MUST NOT include the BINDING-CHANGE
attribute. The minimum limit on Binding Request period defined by STUNMinimum-
KeepAlivePeriod does not apply to Binding Requests that include the BINDING-
CHANGE attribute.
For Binding Requests that include the BINDING-CHANGE attribute, the CPE MUST
follow the retransmission procedures define in [21] to attempt to ensure the successful
reception. If, following these retransmission procedures, the CPE determines that the
Binding Request has failed, it MUST NOT make further attempts to send Binding
Requests that include the BINDING-CHANGE attribute (until the binding subsequently
changes again).
When the CPE determines that address and/or port mapping is in use, and whenever the
CPE determines that the binding has changed (as well as the first time the CPE
determines the binding), the CPE MUST update the value of the
UDPConnectionRequestAddress Parameter in the ManagementServer Object.
Specifically:
 The Host portion of the UDPConnectionRequestAddress MUST be set to the
current public IP address for the binding associated with the UDP Connection
Request as determined from the most recent binding information.
 The Port portion of the UDPConnectionRequestAddress MUST be set to the
current public port for the binding associated with the UDP Connection Request
as determined from the most recent binding information.
When the CPE determines that address and/or port mapping is in use, the CPE MUST
also set the NATDetected Parameter in the ManagementServer Object to true.
If the ACS has set the Notification attribute on the UDPConnectionRequestAddress
Parameter to Active notification, then whenever the binding information has changed, the
CPE MUST establish a connection to the ACS and include the
UDPConnectionRequestAddress in the Inform message, as defined in Annex A.
When the UDPConnectionRequestAddress is changed, if the time since the most recent
Notification on a change to the UDPConnectionRequestAddress is less than the value of
UDPConnectionRequestAddressNotificationLimit, the Notification MUST be delayed
until the specified minimum time period is met.

November 2013 © The Broadband Forum. All rights reserved. Page 167 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Note – In addition to the specified minimum notification period, the CPE MAY use its discretion to
delay notifying the ACS of updated binding information in order to avoid excessive notifications. Such
a delay would only be used if the CPE is confident that the binding is likely to change again within a
brief period. For example, during active discovery of the binding timeout it is reasonable to expect
frequent binding changes. Similarly, a CPE might be able to detect that a security attack is causing
frequent binding changes, and limit the number of notifications until the attack ceases.
If the CPE determines that neither address nor port mapping are in use, then the CPE
MUST indicate this to the ACS by setting the NATDetected Parameter to false, and
setting the UDPConnectionRequestAddress such that the Host and Port are the local IP
address and port on which the CPE is listening for UDP Connection Request messages.

G.2.1.4 UDP Connection Requests

A CPE conforming to this Annex MUST listen for UDP Connection Request messages
on the port that it has designated for this purpose. This MUST be true whether or not the
CPE has detected address or port translation in use, and whether or not the use of STUN
is enabled.
Note – a CPE MUST also continue to listen for HTTP-based Connection Requests as defined in
Section 3.2.2.
The format of the UDP Connection Request message is defined in Section G.2.2.3.
When the CPE receives a UDP Connection Request message, it MUST both authenticate
and validate the message.
A UDP Connection Request message is valid if and only if the following requirements
are met:
 It MUST NOT violate any requirements specified in [6] for an HTTP 1.1
request message.
 The Method given in the Request Line MUST be “GET”.
 The Timestamp given by the value of the “ts” query string argument MUST be
strictly greater than the Timestamp value for the UDP Connection Request
message that had been most recently received, validated, and authenticated.
To allow the above comparison to be made, the CPE MUST maintain a
persistent record of Timestamp value of the most recent UDP Connection
Request that was successfully validated and authenticated (except across CPE
reboots). The Timestamp value for any UDP Connection Request message that
fails to be validated or authenticated MUST NOT be recorded. The CPE MAY
maintain a record of this most recent Timestamp across CPE reboots. If the
CPE does not maintain this value across reboots, then immediately following
the reboot the value zero MUST be used.
The CPE MAY place stricter requirements on the Timestamp than stated above.
The CPE MAY, for example, additionally verify that the Timestamp is within a
time window relative to its understanding of the current time. If a CPE chooses
to do this, it SHOULD avoid making the time window too narrow, in order to
allow for a reasonable margin of error in both the CPE and ACS.

November 2013 © The Broadband Forum. All rights reserved. Page 168 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

 The Message ID given by the value of the “id” query string argument MUST be
distinct from that of the UDP Connection Request message that had been most
recently received, validated, and authenticated.
 The Username given by the value of the “un” query string argument MUST
match the value of the Parameter ManagementServer.ConnectionRequest-
Username.
A UDP Connection Request message is authenticated if and only if the following
requirements are met:
 The Signature given by the value of the “sig” query string argument MUST
match the value of the signature locally computed by the CPE following the
procedure specified in Section G.2.2.3 using the local value of the Parameter
ManagementServer.ConnectionRequestPassword.
Whenever a CPE receives and successfully authenticates and validates a UDP
Connection Request, it MUST follow the same requirements as for a HTTP-based
Connection Request that are defined in Section 3.2.2.
The CPE MUST ignore a UDP Connection Request that is not successfully authenticated
or validated.
The CPE MUST ignore the content of any non-empty Message Body that might be
present in the UDP Connection Request (this allows the possibility of the use of a non-
empty message body in a future version of this protocol).
Because STUN responses and UDP Connection Requests will be received on the same
UDP port, the CPE MUST appropriately distinguish STUN messages from UDP
Connection Requests using the content of the messages themselves. As the first byte of
all STUN messages defined in [21] is either 0 or 1, and the first byte of the UDP
Connection Request is always an ASCII encoded alphabetic letter, the CPE MAY use this
distinction to distinguish between these messages.
Port 7547 has been assigned by IANA for the CPE WAN Management Protocol (see
[17]), and the CPE MAY use this port for UDP Connection Requests.

G.2.2 ACS Requirements

An ACS following the requirements of this Annex MUST be associated with a STUN
server that follows the requirements defined in this Section.

G.2.2.1 STUN Server Requirements

The STUN server MUST conform to all of the requirements defined in [21], with the
following exceptions, which the STUN server MAY choose not to implement.
 The STUN server need not support the Shared Secret exchange mechanism
defined in [21]. If message integrity is used, the shared secrets MUST be
statically provisioned, and correspond to the STUNUsername and
STUNPassword Parameters in the ManagementServer Object in the CPE.
 The STUN server need not support a secondary source IP address or port for
sending Binding Responses (A2/P2). If it does not, the CHANGED-ADDRESS

November 2013 © The Broadband Forum. All rights reserved. Page 169 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

attribute SHOULD be filled in with the primary address and port (A1/P1), and the
STUN server MAY ignore the CHANGE-REQUEST attribute if received in a
Binding Request.
The STUN server MAY require message integrity for any received Binding Requests of
its choosing by responding to the request with a Binding Error Response with fault code
401 (Unauthorized).

G.2.2.2 Determination of the Binding Information

The ACS can choose either of the two defined mechanisms to determine the current
binding information from a CPE.

G.2.2.2.1 STUN-based Approach

If the ACS chooses to use the attributes received by the STUN server, it SHOULD set a
non-empty STUNUsername and STUNPassword in the ManagementServer Object of
each CPE. The STUNUsername MUST be unique among all CPE managed by the
corresponding ACS to ensure that the CPE can be distinguished. The STUNPassword
SHOULD be unique among all CPE managed by the corresponding ACS, and SHOULD
follow the password strength guidelines specified in [21].
Whenever the STUN server receives a Binding Request that includes both the BINDING-
CHANGE and CONNECTION-REQUEST-BINDING attributes:
 The STUN server SHOULD respond with a Binding Error Response with fault
code 401 (Unauthorized) in order to force the CPE to retransmit the Binding
Request with message integrity included.
 When the STUN server receives the retransmitted request with message integrity,
it SHOULD authenticate the requester. This would likely involve communication
between the STUN server and ACS if they were not implemented as a single
entity.
 If the authentication fails, the STUN server MUST respond with a Binding
Request Error as defined in [21] and take no further action.
 If the authentication is successful, the STUN server SHOULD extract the source
IP address and port from the Binding Request message, and record these as the
new IP address and port to be used for UDP Connection Requests. Depending on
the implementation, this might involve the STUN server informing the ACS of
the IP address and port along with the corresponding STUNUsername, from
which the ACS would then record this information for the CPE corresponding to
that STUNUsername.
 The STUN server SHOULD perform the above only once for a given Transaction
ID in the Binding Request. Redundant copies of the Binding Request with the
same Transaction ID SHOULD be ignored.
Using this approach, the STUN server MAY choose not to require message integrity or
authenticate any Binding Requests other than those for which it follows the above
procedures to determine the binding information.

November 2013 © The Broadband Forum. All rights reserved. Page 170 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

The ACS MAY determine the current binding at any time even if no change was notified
by following the above procedure on any received Binding Request for which the
CONNECTION-REQUEST-BINDING attribute is present. The required presence of the
USERNAME attribute in these Binding Requests allows the ACS to tentatively
determine the CPE’s identity prior to subsequent authentication. This allows an ACS to
periodically verify the binding information to ensure that it is up-to-date in case explicit
indications of a binding change had failed to reach the ACS.
If the ACS determines that the CPE is no longer behind a NAT that is doing address or
port mapping, the ACS MAY use HTTP-based Connection Requests as defined in
Section 3.2.2.

G.2.2.2.2 Notification-based Approach

If the ACS chooses to use Active notification on the UDPConnectionRequestAddress
Parameter, it SHOULD do the following:
 Set the Notification attribute for the UDPConnectionRequestAddress Parameter to
Active notification.
 Record changes to the UDPConnectionRequestAddress Parameter whenever this
Parameter is included in the Inform message, and use the most recently recorded
value to determine the destination of UDP Connection Request messages.
Specifically, the destination IP address for UDP Connection Request messages is
determined from the “host” portion of this Parameter, and the destination port is
determined from the “port” portion of this Parameter. If the host is given as a
domain name, the ACS MUST use DNS to determine the associated IP address.
If the port is not explicitly given in the UDPConnectionRequestAddress
Parameter, port 80 MUST be used as the default value.
 Observe the value of the NATDetected Parameter (either by reading it when
UDPConnectionRequestAddress changes, or by enabling Active notification on
this Parameter as well). Whenever this Parameter is false, the ACS MAY use
HTTP-based Connection Requests as defined in Section 3.2.2.
Using this approach, the ACS MAY choose not to require message integrity or
authenticate any STUN Binding Requests, since these requests are not used to convey
information to the ACS. In this case, the ACS need not set a STUNUsername or
STUNPassword in the CPE.

G.2.2.3 UDP Connection Requests

The ACS MUST send UDP Connection Request messages from the same source IP
address and port as the STUN server.
A UDP Connection Request message MUST be transmitted within a single UDP packet
sent to the IP address and port determined by the ACS as described in Section G.2.2.2.
The ACS SHOULD send multiple copies of the same UDP Connection Request message
in order to reduce the likelihood that the message is lost due to packet loss. When an
ACS sends multiple copies of the same UDP Connection Request, the content of the

November 2013 © The Broadband Forum. All rights reserved. Page 171 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

message (including the message ID, timestamp, and cnonce, as defined below) MUST be
identical for each successive copy.
There is no response message associated with a UDP Connection Request message.
The format of the UDP Connection Request message is derived from the format of an
HTTP 1.1 [6] GET message, though the HTTP 1.1 protocol itself is not used.
Specifically, the UDP Connection Request message MUST conform to the following
requirements:
 It MUST be a valid HTTP 1.1 GET message as defined in [6].
 It MUST contain no Message Body.
 If a Content-Length header is present, its value MUST be zero.
 The Method given in the Request Line MUST be “GET”.
 The Request-URI given in the Request Line MUST be an Absolute-URI
according to the rules defined in [12]. The URI MUST be formed as follows:
o The Scheme portion of the URI MUST be “http” or “HTTP”.
o The Authority portion of the URI MUST be as specified in [12]. The ACS
MAY set this to the value of ManagementServer.UDPConnectionRequest-
Address, if it is known. Otherwise, the ACS MUST derive this string
from the actual destination IP address and port to which the UDP
Connection Request message will be sent. The “port” portion of this
string MUST be present unless the destination port number is “80”.
o The Path portion of the URI MUST be empty.
o The Query portion of the URI MUST contain a query string encoded as
defined by the “application/x-www-form-urlencoded” content type
defined in [23]. The query string MUST contain the following name-
value pairs:
Name Value
ts Timestamp. The number of seconds since the Unix epoch until the time the
message is created (the standard Unix timestamp).
id Message ID. An unsigned integer value that MUST be set to the same value for
all retransmitted copies of the same UDP Connection Request. The value MUST
change between successive distinct UDP Connection Requests.
un Username. The value of the Parameter ManagementServer.ConnectionRequest-
Username as read from the CPE.
cn Cnonce. A random string chosen by the ACS.
sig Signature. Formed from the 40-character hexadecimal representation (case
insensitive) of HMAC-SHA1 (Key, Text) [19], where:
 Key is the value of the Parameter ManagementServer.ConnectionRequest-
Password as read from the CPE.
 Text is a string formed by concatenating the following elements (in the order
listed, with no spaces between items):
 The value of the ts (Timestamp) element
 The value of the id (Message ID) element
 The value of the un (Username) element
 The value of the cn (Cnonce) element

November 2013 © The Broadband Forum. All rights reserved. Page 172 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Below is an example Request-URI:

http://10.1.1.1:8080?ts=1120673700&id=1234&un=CPE57689
&cn=XTGRWIPC6D3IPXS3&sig=3545F7B5820D76A3DF45A3A509DA8D8C38F13512

G.2.3 Message Flows

The following figures show example message flows associated with the procedures
defined in Sections G.2.1 and G.2.2 to support Connection Requests to devices behind a
NAT gateway.
In all of the examples, the address/port pairs use the notation (A, P), where A is the IP
address and P is the port. In the examples, the CPE uses (A1, P1) as its primary port (the
port on which the CPE is listening for UDP Connection Request messages) and (A1, P2)
is its secondary port (used for binding timeout discovery). When passing through a NAT
Gateway, these addresses are translated to (A1', P1') and (A1', P2'), respectively. In all of
the examples it is assumed that the STUN Server does not have a secondary address/port
and thus the CHANGED-ADDRESS attribute in the Binding Response (which need not
be used by the CPE) contains its primary address/port, (A3, P3).

Figure 11 shows the periodic binding discovery and binding maintenance flows where the
CPE sends the Binding Request from the primary source port and includes the
CONNECTION-REQUEST-BINDING and (if a Username had been set) USERNAME
attributes. In this example it is assumed that the STUN Server has not chosen to
authenticate the request.

(A1, P1) (A1', P1') (A3, P3)

(A1, P2) (A1', P2') ACS /
CPE Gateway STUN Server

From (A1, P1) BINDING-REQUEST (CONNECTION-REQUEST-

To (A3, P3) BINDING : USERNAME)

BINDING-RESPONSE (MAPPED-ADDRESS=A1',P1' : From (A3, P3)

SOURCE-ADDRESS=A3,P3 : CHANGED-ADDRESS=A3,P3) To (A1', P1')

Figure 11 – Binding discovery / maintenance from the primary source port

November 2013 © The Broadband Forum. All rights reserved. Page 173 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Figure 12 shows a Binding Request sent by the CPE from its secondary source port for
the purpose of discovering whether or not the primary binding has timed out in the NAT
gateway. In this case the Binding Request does not include the CONNECTION-
REQUEST-BINDING attribute since it is not sent from the primary source port. The last
leg of the exchange (shown in grey) will not occur if the primary binding has timed out.

(A1, P1) (A1', P1') (A3, P3)

(A1, P2) (A1', P2') ACS /
CPE Gateway STUN Server

From (A1, P2) BINDING-REQUEST (RESPONSE-ADDRESS=A1', P1')

To (A3, P3)

BINDING-RESPONSE (MAPPED-ADDRESS=A1',P2' : From (A3, P3)

SOURCE-ADDRESS=A3,P3 : CHANGED-ADDRESS=A3,P3 : To (A1', P1')
REFLECTED-FROM=A1',P2')

Figure 12 – Binding Request from secondary source port for binding timeout discovery

Figure 13 shows a Binding Change notification where the STUN Server has chosen to
make use of the STUN-based approach (see Section G.2.2.2.1), and therefore
authenticates the Binding Request prior to storing the information associating the
Username with the current binding address and port.

(A1, P1) (A1', P1') (A3, P3)

(A1, P2) (A1', P2') ACS /
CPE Gateway STUN Server

From (A1, P1) BINDING-REQUEST (CONNECTION-REQUEST-

To (A3, P3) BINDING : BINDING-CHANGE : USERNAME)

BINDING-ERROR-RESPONSE (401) From (A3, P3)

To (A1', P1')

From (A1, P1) BINDING-REQUEST (CONNECTION-REQUEST-

To (A3, P3) BINDING : BINDING-CHANGE : USERNAME :
MSG-INTEGRITY)
Associate
Username
with
(A1', P1')

BINDING-RESPONSE (MAPPED-ADDRESS=A1',P1' : From (A3, P3)

SOURCE-ADDRESS=A3,P3 : CHANGED-ADDRESS=A3,P3 : To (A1', P1')
MSG-INTEGRITY)

Figure 13 – Binding change notification authenticated by the ACS

November 2013 © The Broadband Forum. All rights reserved. Page 174 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Figure 14 shows a Binding Change notification where the STUN Server has chosen to
make use of the Notification-based approach (see Section G.2.2.2.2), and therefore does
not need to authenticate the Binding Request since the ACS instead uses CPE WAN
Management Protocol Notification to update the binding information.

(A1, P1) (A1', P1') (A3, P3)

(A1, P2) (A1', P2') ACS /
CPE Gateway STUN Server

From (A1, P1) BINDING-REQUEST (CONNECTION-REQUEST-

To (A3, P3) BINDING : BINDING-CHANGE : USERNAME)

BINDING-RESPONSE (MAPPED-ADDRESS=A1',P1' : From (A3, P3)

SOURCE-ADDRESS=A3,P3 : CHANGED-ADDRESS=A3,P3) To (A1', P1')

Figure 14 – Binding change notification not authenticated by the ACS

Figure 15 shows a UDP Connection Request message sent to the CPE to initiate a CPE
WAN Management Protocol Session. In this example, the STUN Server sends the
identical UDP Connection Request multiple times to improve the likelihood of successful
reception by the CPE.

(A1, P1) (A1', P1') (A3, P3)

(A1, P2) (A1', P2') ACS /
CPE Gateway STUN Server

UDP Connection Request From (A3, P3)

To (A1', P1')

UDP Connection Request From (A3, P3)

To (A1', P1')

Figure 15 – UDP Connection Request

November 2013 © The Broadband Forum. All rights reserved. Page 175 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

G.3 Security Considerations

The following security considerations associated with the procedures defined in this
Annex are identified:
 The STUN specification describes several potential attacks using the STUN
mechanism. The reader is referred to Section 12 of RFC 3489 [21] for a detailed
description of these potential attacks and the associated risk.
 Because binding changes will result in actions required by the ACS—
authentication of a CPE, and subsequent database update, and potentially
establishment of a CPE WAN Management Protocol Session over which to
receive an Inform—attacks that can cause frequent changes to the NAT binding
could result in an increased burden on the ACS. The ACS can set a minimum
limit on the rate of Notifications on binding changes if Active notification is used.
However, there is a tradeoff between the maximum Notification rate and the
length of time for which the ACS might not be able to send Connection Requests
to the CPE due to out-of-date information.

November 2013 © The Broadband Forum. All rights reserved. Page 176 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Annex H. Software Module

Management UUID
Usage

H.1 Overview
The Software Module Management mechanism uses a UUID (see RFC 4122 [34] for a
complete definition of UUID) to uniformly identify a Deployment Unit across CPE.
Since Deployment Units can be installed multiple times on a single CPE (e.g. multiple
versions of the same Deployment Unit or the same version of the Deployment Unit on
different Execution Environments), a Deployment Unit on a specific CPE is uniquely
identified by the combination of UUID, version, and Execution Environment that the
Deployment Unit is installed upon, but the UUID is still the uniform unique identifier of
that Deployment Unit (i.e. this means that the UUID will be the same independent of the
version of the Deployment Unit). A version 3 UUID is a method for generating UUIDs
from “names” that are unique within some “namespace”, which means that a UUID
generated by different actors but using the same “name” and “namespace” will cause the
generation of the same exact UUID. The Software Module Management mechanism
requires, whether the ACS or the CPE generates the UUID, that the UUID be generated
in the exact same manner following both the rules defined in Section 4.3 / RFC 4122 [34]
and the rules defined within this Annex.
Section 4.3 / RFC 4122 [34] identifies the following high-level requirements for a
Version 3 UUID:
 The UUIDs generated at different times from the same name in the same namespace MUST be
equal.
 The UUIDs generated from two different names in the same namespace should be different
(with very high probability).
 The UUIDs generated from the same name in two different namespaces should be different with
(very high probability).
 If two UUIDs that were generated from names are equal, then they were generated from the
same name in the same namespace (with very high probability).
The remainder of this Annex defines additional rules that MUST be followed by the ACS
and CPE when generating a UUID as well as under what circumstances a CPE will be
required to generate a UUID.

November 2013 © The Broadband Forum. All rights reserved. Page 177 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

H.2 UUID Generation Requirements

The following set of additional requirements ensures that the Version 3 UUID will be
uniform regardless of whether the ACS or CPE generates it:
1) The FQDN “namespace” UUID as defined in Appendix C /RFC 4122 [34] MUST
be used: 6ba7b810-9dad-11d1-80b4-00c04fd430c8

2) The SHA-1 hash algorithm MUST be used instead of MD5

3) The “name” will be the FQDN of the Deployment Unit, which MUST be a
combination of the Deployment Unit’s Name (the value that will be contained
within the DeploymentUnit.{i}.Name Parameter) and the Deployment Unit
Vendor’s domain name (the value that will be contained within the
DeploymentUnit.{i}.Vendor Parameter). The format is: ‘<Name> + “.” +
<Vendor> + “.”’. For example, if the DU Vendor is “broadband-forum.org” and
the DU Name is “sample1”, then the FQDN of the DU is “sample1.broadband-
forum.org.”

Note, as the Deployment Unit’s Name is used within generation of the FQDN, it MUST be
altered if it contains any characters other than 0-9, a-z, A-Z, _ (underscore), or – (hyphen).
Percent-encoding MUST be used to replace any other characters (i.e. a ‘%’ character
followed by the ASCII hex value of the replaced character). For example, a Deployment Unit
Name of “sample.1” would be converted to “sample%2e1”.
An example of a Version 3 UUID looks like:
76183ed7-6a38-3890-66ef-a6488efb6690

H.3 CPE Requirements

There are three circumstances when a CPE MUST generate its own UUID:
a) Factory-Installed Deployment Units : a Deployment Unit is installed at factory
time without the aid of an ACS

b) LAN-Side-Installed Deployment Units : a Deployment Unit is installed by a

LAN-Side management mechanism (e.g. UPnP DM SMS, CLI, or GUI) without
the aid of an ACS

c) ACS-Installed Deployment Units : a Deployment Unit is installed by an ACS, but

the ACS either does not send the UUID or sends an empty string as the UUID
within the Install operation of the ChangeDUState RPC.

In these circumstances the CPE MUST generate the UUID as it installs the Deployment
Unit. The ACS can discover / validate the generated UUID by either inspecting the
DUStateChangeComplete or inspecting the Deployment Unit Data Model table.

November 2013 © The Broadband Forum. All rights reserved. Page 178 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Annex I.

Annex I is intentionally left blank

November 2013 © The Broadband Forum. All rights reserved. Page 179 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Annex J. CWMP Proxy

Management

J.1 Introduction
CWMP can be extended to devices that do not have a native CWMP Endpoint of their
own, but instead support another management protocol or “Proxy Protocol”. A CPE
Proxier is a CPE that supports a CWMP Endpoint(s) and also supports one or more Proxy
Protocols (example services include UPnP DM, Z-Wave etc.). A CPE Proxier uses these
Proxy Protocols to manage the devices connected to it, i.e. the Proxied Devices. This
approach is designed to support Proxy Protocols of all types that can exist in the CPE
network now or in the future.

Figure 16 – Proxy management terminology

The function of the CPE Proxier is to seamlessly incorporate all of the elements and
mechanisms/methods of the Proxy Protocol(s). Independent of the implementation, the
ACS manages the Proxied Device through CWMP mechanisms, and is not aware of any
Proxy Protocol commands that may be utilized to complete the requested actions.
In order to support a wide range of Proxy Protocols and devices, CWMP has two ways to
model a Proxied Device; as a Virtual CWMP Device and using an Embedded Object.
A Virtual CWMP Device is used to model a more complex Proxied Device such as a
bridge, router, Set Top Box or devices of similar type. The Virtual CWMP Device
Mechanism represents a Proxied Device with a CWMP Endpoint in the CPE Proxier.
An Embedded Object is used to model a simpler Proxied Device such as a binary sensor,
power switch or devices of similar type. The Embedded Object Mechanism utilizes an
Embedded Object or Service Object within the CPE Proxier itself to represent the
Proxied Device.
This Annex describes each CPE Proxier Mechanism and gives guidelines for dictating
which approach might be appropriate for a given Proxy Protocol.

November 2013 © The Broadband Forum. All rights reserved. Page 180 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

J.2 The Virtual CWMP Device Mechanism

The Virtual CWMP Device Mechanism provides the ACS with a CWMP Endpoint
terminated on the CPE Proxier for the Proxied Device. The Virtual CWMP client will
function with the same requirements as a CWMP client. The CPE Proxier that is
supporting a Proxied Device with a Virtual CWMP Device is responsible for creating,
supporting and sustaining a CWMP Data Model for each such Proxied Device.
The CPE Proxier is bound by the CWMP for each device it represents and MUST
maintain a unique ManagementServer.ConnectionRequestURL for itself and for each
device it is Proxying for. When the CPE Proxier establishes a connection to the ACS
using a Virtual CWMP Device it will appear as the Proxied Device.
The Virtual CWMP Device(s) supported by the CPE Proxier MAY share the same IP
address as the CPE Proxier.

J.2.1 Data Model Requirements

For the CPE Proxier the DeviceInfo.SupportedDataModel table MUST only contain
entries relevant to the CPE Proxier.
For the Virtual CWMP Device representing the Proxied Device the
DeviceInfo.SupportedDataModel table MUST only contain entries relevant to the
Proxied Device.
The CPE Proxier supporting a Virtual CWMP Device(s) MUST provide a
ManagementServer.VirtualDevice table with entries for each of the Proxied Devices it
represents, regardless of the Proxy Protocol it uses to communicate with them. The ACS
MAY use the ManagementServer.VirtualDevice table to identify the Proxied Device(s)
that are being proxied by the CPE Proxier.
For each of the Proxied Devices supported by the CPE Proxier, the Virtual Device(s)
Data Model(s) MUST contain an associated DeviceInfo.ProxierInfo Object regardless of
the Proxy Protocol that connects them.

Figure 17 – CPE Proxier and Proxied Device references

J.2.2 Proxied Device Identification and Modeling

The Proxied Device MUST support or provide information required by CWMP in the
DeviceInfo Object (it MUST have a means of uniquely identifying itself beyond the
transport assigned address).

November 2013 © The Broadband Forum. All rights reserved. Page 181 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

The CPE Proxier MUST obtain a unique OUI and Serial Number from the Proxied
Device for the Virtual CWMP Device using the following options in order:
1. Use a unique OUI and Serial Number provided by the Proxied Device via the
Proxy Protocol.
2. If the Proxy Protocol does not provide a unique OUI and Serial Number for the
Proxied Device, the CPE Proxier MUST use the Proxied Device’s MAC address
to produce the OUI (defined in [36]) and set the Serial Number = MAC address.
3. If the CPE Proxier cannot obtain the Proxied Device’s MAC address (or a MAC
address is not provided) the CPE Proxier MUST use the unique32 physical device
identifier to provide the unique OUI and Serial Number.
When modeling a Proxied Device as a Virtual CWMP Device:
1. The Proxied Device MUST be able to be uniquely identified by its local Proxy
Protocol or extensions that provide identification beyond the transport assigned
addresses each time it comes online.
2. If the Proxied Device supports a connectivity stack similar to the interface stack
described in TR-181 [32], this SHOULD be modeled using the interface stack.
3. The Proxied Device MUST support a Reboot mechanism.
4. The Proxied Device SHOULD support a Download mechanism, and MAY
support other optional RPCs such as FactoryReset and ChangeDUState.

J.2.3 Proxied Device Availability

When a Connection Request is received for the Virtual CWMP Device and the Proxied
Device is offline the CPE Proxier MUST respond with an HTTP 503 failure (see Section
3.2.2). To ensure that the ACS is contacted when the Proxied Device is once again
available, the CPE Proxier MUST send a BOOT Inform via the Virtual CWMP Device
when the Proxied Device comes back online.
If the CPE Proxier fails to successfully complete a CWMP Session for a Virtual CWMP
Device, the Virtual CWMP Device MUST follow the session retry logic in Section
3.2.1.1
When a CPE Proxier Reboots:
 The CPE Proxier MUST send a BOOT Inform for itself.
 The CPE Proxier SHOULD NOT send BOOT Informs for any associated Virtual
CWMP Devices.
If the Proxied Device communicates a Reboot to the CPE Proxier, the CPE Proxier MAY
(depending upon policy) send a BOOT Inform for the Virtual Device.

32
Since the mechanism to create the unique OUI and Serial Number from the unique physical device identifier is not
defined, the same physical device may be represented with a different unique OUI and Serial Number from
different CPE Proxiers.

November 2013 © The Broadband Forum. All rights reserved. Page 182 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

J.3 The Embedded Object Mechanism

The Embedded Object Mechanism of providing a CWMP interface to a Proxied Device
utilizes the CPE Proxiers Data Model to represent the Proxied Devices. This is done by
representing the Proxied Devices as Object instances within the CPE Proxier’s (Root or
Service) Data Model.

J.3.1 Proxied Device Data Modeling and Provisioning

To provide visibility of which Objects in the CPE Proxier Data Model represent Proxied
Devices, the CPE Proxier MUST support an EmbeddedDevice table with an entry for
each supported Embedded Object. Each ManagementServer.EmbeddedDevice table entry
MUST reference a row in a Multi-Instance Object that represents the Embedded Device.
The CPE Proxier MUST provide all the DT instances(s) (see Annex B/TR-106 [13]) for
the Proxied Device types it supports in the DeviceInfo.SupportedDataModel table.
The CPE Proxier MUST reference the DeviceInfo.SupportedDataModel table entry(s) for
each Proxied Object in the ManagementServer.EmbeddedDevice table.
For the CPE Proxier supporting multiple unique Proxied Device types within a single or
multiple Proxy Protocols, each unique Proxied Device MUST be represented by at least
one DT instance in the DeviceInfo.SupportedDataModel table and MAY be represented
by multiple entries.
Multiple instances of an Object (all supporting the same device type) MAY be described
by a single DT entry.
Guidelines in using Data Model Objects to support Proxied Devices:
1) The Proxied Devices that are not able to uniquely be identified by their local
Proxy Protocol beyond the transport assigned address (such that they are not
uniquely identified when removed and re-inserted into the Proxy Protocol
network) MUST use Data Model Objects to provide proxy support.
2) The Proxied Devices that do not use an interface stack to model their connectivity
or features SHOULD use Data Model Objects to provide proxy support.
3) The Proxied Devices that might provide no support of a reboot, factory reset
and/or a download command SHOULD use Data Model Objects to provide proxy
support. If such a command is needed it could be reflected in the associated Data
Model, see Section I.3.4.
4) The Proxied Devices that support optional RPCs such as ChangeDUState
SHOULD NOT use Data Model Objects to provide proxy support.

J.3.2 Proxied Device Availability

When the CPE Proxier receives a CWMP command for an Object or Parameter that
resides on the Proxied Device, it MUST attempt to immediately execute the associated
Proxy Protocol command(s) to the Proxied Device.
Prior to the CWMP Session timeout the CPE Proxier MUST return a RPC response for
the command.

November 2013 © The Broadband Forum. All rights reserved. Page 183 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

If the Proxy Protocol commands are not successfully responded to or applied prior to the
CWMP Session timeout the CPE Proxier MUST:
 If the command was to perform configuration, the CPE Proxier MUST return a
committed response (if supported by the RPC33).
 If the command was to retrieve information the CPE Proxier MUST return a
cached result for the requested Parameter values.
Until the Proxy Protocol commands are responded to or applied (or retries exceeded), the
CPE Proxier MUST continue to attempt to complete (or verify) the commands via the
Proxy Protocol. While this process continues the CPE Proxier MUST return a cached
result for the effected Parameters and Objects when requested.
When the command(s) are finally responded to or applied (or retries exceeded), the CPE
Proxier MUST update the appropriate
ManagementServer.EmbeddedDevice.{i}.LastSyncTime and/or
ManagementServer.EmbeddedDevice.{i}.CommandProcessed Parameters
Depending upon the Proxy Protocol, devices that are removed from the network or are no
longer available for a period of time SHOULD be removed from the Data Model.
Depending upon the Proxy Protocol when the device returns to online status (or re-
discovered) if there is a unique identifier it SHOULD continue to be represented by the
original Object from initial discovery. The methods to "match" this device with the Data
Model Object entry are implementation dependent.
If the CPE Proxier can detect that the Proxied Device was Rebooted it MAY utilize a
Data Model Parameter to mark the event. The ACS might set the Notification Attribute of
the Data Model Parameter to receive notification that the Proxied Device has Rebooted.

33
SetParameterAttributes does not allow a committed response.

November 2013 © The Broadband Forum. All rights reserved. Page 184 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Annex K. XMPP Connection

Request

K.1 Introduction
The CPE WAN Management Protocol can be used to remotely manage CPE that are
connected via a LAN through a Gateway. When an ACS manages a Device connected
via a NAT Gateway or firewall-enabled Gateway (where the Device cannot be contacted
directly by the ACS), the CPE WAN Management Protocol can still be used for
management of the Device, but with the limitation that the Connection Request
mechanism defined in Section 3.2.2 that allows the ACS to initiate a Session might not be
usable.
The procedures defined in this Annex allow an ACS to initiate a Session with any
Device, including Devices that cannot be contacted directly by the ACS. This provides
the equivalent functionality of the Connection Request defined in Section 3.2.2, but
makes use of a different mechanism, based on Extensible Messaging and Presence
Protocol (XMPP), to accommodate this scenario.
As it relates to Devices that cannot be contacted directly by the ACS, the mechanism
defined in this Annex does not assume that the Gateway, through which the Device is
connected, supports the CPE WAN Management Protocol. This mechanism requires
support only in the Device and the associated ACS.

K.2 Procedures
To accommodate the ability for an ACS to issue the equivalent of a Connection Request
to a CPE, the following is required:
 The CPE MUST be able to establish a secure and authenticated connection to an
XMPP Server.
 The CPE MUST be able to maintain a connection to an XMPP Server through
which the XMPP Server can send unsolicited messages from an ACS-defined set
of allowed addresses.
To accomplish the above items, this Annex defines a particular set of messages to be sent
across a standard XMPP (as defined in RFC 6120 [37]) network. The XMPP-based
Connection Request mechanism augments the existing HTTP-based Connection Request
mechanism defined in Section 3.2.2. The procedures for making use of XMPP to issue a
Connection Request to a CPE are summarized as follows:
1. The ACS establishes a connection to an XMPP Server.

November 2013 © The Broadband Forum. All rights reserved. Page 185 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

2. The ACS enables the use of XMPP in the Device by configuring an XMPP. -
Connection object, configuring the CPE’s ManagementServer Object to reference
the XMPP.Connection Object, and optionally configuring the set of allowed
Jabber IDs within the Device’s ManagementServer Object (this is shown as a
SetParameterValues in the following Figure, but may also include an AddObject).
This step can be omitted if the CPE is pre-provisioned with the XMPP connection
values in its default settings.
3. The Device establishes an XMPP connection to the specified XMPP Server.
4. Whenever the ACS wishes to establish a connection to the CPE, it can send an
XMPP Connection Request (an XMPP IQ Stanza containing a Connection
Request message to its XMPP Server specifying the “to” address that matches the
CPE where the Connection Request needs to be sent and a “from” address that
matches one of the allowed Jabber IDs – see K.2.2.2 for details) to the XMPP
Server.
5. The XMPP Server sends the XMPP IQ Stanza to the appropriate Device.
6. The Device issues an Inform request to the ACS that is specified in its
ManagementServer.URL Parameter.
Note – The XMPP Connection Request mechanism is mostly described as utilizing a single
XMPP Server, but there could be multiple XMPP Servers depending on the deployment. Some
examples would be to deploy a single domain with multiple XMPP Servers that are clustered
together or to deploy multiple domains where each domain consists of a cluster of XMPP
Servers and they can all communicate to each other.

November 2013 © The Broadband Forum. All rights reserved. Page 186 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Figure 18 – XMPP Connection Request Message Sequence

K.2.1 CPE Requirements

A CPE conforming to this Annex MUST support the XMPPBasic:1 and
XMPPConnReq:1 profiles as defined in tr-157-1-8.xml [38].
Whenever the ManagementServer.ConnReqXMPPConnection Parameter references an
enabled instance of the XMPP.Connection table, CPE following the requirements of this
Annex MUST make use of the procedures defined in XMPP (as defined in RFC 6120
[37]) to connect to the XMPP Server. The CPE MUST:
 Determine the public IP address of the XMPP Server using the rules defined in
Section 3.2/RFC 6120 [37] and the recommendations described in Appendix
III.4.1.

November 2013 © The Broadband Forum. All rights reserved. Page 187 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

 Open an XML Stream to the XMPP Server and accept an XML Stream from the
XMPP Server as defined in Section 4.2/RFC 6120 [37] and further described in
Appendix III.4.2. Note: XML Streams are unidirectional and this XMPP
Connection Request mechanism requires the use of two XML Streams over a
single TCP connection as recommeneded in Section 4.5/RFC 6120 [37] for Client
to Server sessions.
 Use TLS to establish an encrypted and secure TCP connection with the XMPP
Server as defined in Section 5/RFC 6120 [37] and further described in Appendix
III.4.3 (see K.2.1.1 below for XMPP Connection Request specific details).
 Use SASL to authenticate with the XMPP Server as defined in Section 6/RFC
6120 [37] and further described in Appendix III.4.4 (see K.2.1.2 below for XMPP
Connection Request specific details).
 Ensure that the value of the ManagementServer.ConnReqJabberID Parameter
contains the same value as the contents of the JabberID Parameter contained
within the XMPP.Connection instance referenced by the ConnReqXMPP-
Connection Parameter. Details on how the value of the JabberID Parameter is
computed can be found in Appendix III.3.1.
 Maintain the TCP connection to the XMPP Server by utilizing the “whitespace
keepalive” mechanism as defined in Section 4.6.1/RFC 6120 [37] and further
described in Appendix III.5.
 Listen for XMPP Connection Request messages, and act on these messages when
they arrive (see K.2.1.3 below for details).
 If the connection to the XMPP Server is ever lost, reestablish the connection as
defined in Section 3.3/RFC 6120 [37] and further described in Appendix III.4.5.
Whenever the MangementServer.ConnReqXMPPConnection Parameter references an
enabled instance of the XMPP.Connection table, CPE following the requirements of this
Annex SHOULD:
 Establish the Connection Request XMPP connection before establishing the
CWMP Session where the “1 BOOT” or “13 WAKEUP” event codes are to be
delivered. In the event of a change to the ConnReqJabberID Parameter, this will
allow the CPE to deliver the applicable “4 VALUE CHANGE” event code along
with the “1 BOOT” or “13 WAKEUP” event code and remove the need for the
CPE to immediately establish another CWMP Session for the delivery of said
value change event code.
The details of these functions as they apply to the XMPP Connection Request mechanism
are defined in the following Sections (details of functions that are generic to XMPP are
described in Appendix III).
Note – While the CPE requirements defined here certainly apply to a Device connected via
LAN to a Gateway, the same procedures can be followed by a Gateway, which might be
operating behind a network-based NAT gateway. Thus the requirements are defined
generically for CPE, which might be either a Device or Gateway.

November 2013 © The Broadband Forum. All rights reserved. Page 188 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

K.2.1.1 XMPP Connection Encryption

When the ManagementServer.ConnReqXMPPConnection Parameter references an
enabled instance of the XMPP.Connection table, CPE following the requirements of this
Annex MUST negotiate a secure connection if TLS is considered “mandatory-to-
negotiate” for all client-to-server XMPP connections that are used for XMPP Connection
Requests (see K.3 for recommendations about XMPP Server deployments). If TLS is
considered “mandatory-to-negotiate”, then the XMPP connection is encrypted using the
STARTTLS extension of the Transport Layer Security (TLS) protocol as defined in
Section 5/RFC 6120 [37].

K.2.1.2 XMPP Channel Authentication

When the ManagementServer.ConnReqXMPPConnection Parameter references an
enabled instance of the XMPP.Connection table, CPE following the requirements of this
Annex MUST authenticate with the XMPP Server after establishing an XMPP
connection. The XMPP connection is authenticated using the Simple Authentication and
Security Layer (SASL) protocol as defined in Section 6/RFC 6120 [37]. The Username
and Password parameters of the XMPP.Connection object are used as the credentials for
the SASL authentication procedure.

K.2.1.3 XMPP Connection Request

A CPE conforming to this Annex MUST listen for XMPP Connection Request messages
sent from an allowed list of Jabber IDs and generated by the XMPP Server specified by
the XMPP.Connection instance referenced within the ManagementServer.ConnReq-
XMPPConnection Parameter.
Note – a CPE MUST also continue to listen for HTTP-based Connection Requests as defined
in Section 3.2.2.
The format of the XMPP Connection Request message is defined in Annex K.2.3. When
the CPE receives an XMPP Connection Request message, it MUST both validate and
authenticate the message.
An XMPP Connection Request message is valid if and only if the following requirements
are met:
 The XMPP Connection Request message MUST be delivered within an XMPP IQ
Stanza across an XML Stream that has been TLS secured according to Annex
K.2.1.1 and authenticated according to Annex K.2.1.2.
 The XMPP Connection Request message MUST be well-formed XML and
validated against the cwmp-xmppConnReq-1-0.xsd (http://www.broadband-
forum.org/cwmp/cwmp-xmppConnReq-1-0.xsd).
 The “from” address contained within the XMPP IQ Stanza MUST match one of
the addresses contained within the list-based ManagementServer.ConnReq-
AllowedJabberIDs Parameter (unless the value of that Parameter is empty, which
means that all addresses are allowed).

November 2013 © The Broadband Forum. All rights reserved. Page 189 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

 The value of the “username” element within the “connectionRequest” element

MUST match the value of the ManagementServer.ConnectionRequestUsername
Parameter.
An XMPP Connection Request message is authenticated if and only if the following
requirements are met:
 The value of the “password” element within the “connectionRequest” element
MUST match the value of the ManagementServer.ConnectionRequestPassword
Parameter.
Whenever a CPE receives, successfully validates, and authenticates an XMPP
Connection Request, it MUST establish a connection with its pre-determined ACS as
described in Section 3.2.1 following the generic Connection Request requirements (as
defined in 3.2.2.1) and further qualified in the following bullet points:
 The CPE SHOULD restrict the number of Connection Requests for a particular
CWMP Endpoint that it accepts during a given period of time in order to further
reduce the possibility of a denial of service attack. If the CPE chooses to reject a
Connection Request for this reason, the CPE MUST respond to that Connection
Request with the following XMPP specific error: error code 503 with a “service-
unavailable” child (see K.2.3.3 for an example).
 If the CPE is already in a Session with the ACS with at least one CWMP Endpoint
when it receives one or more Connection Requests, it MUST NOT terminate any
Session against any CWMP Endpoint prematurely as a result. The CPE MUST
instead take one of the following transport specific alternative actions:
 Reject each Connection Request by responding with error code 503 and a
“service-unavailable” child (see K.2.3.3 for an example).
 Following the completion of the CWMP Endpoint’s current Session, initiate
exactly one new Session at a time (regardless of how many Connection Requests
had been received during the previous Session) in which it includes the
“6 CONNECTION REQUEST” EventCode in the Inform. The Connection
Requests that are not accepted MUST be rejected (with error code 503 and a
“service-unavailable” child [see K.2.3.3 for an example]). If the new Session is
for the CWMP Endpoint currently in Session, the CPE MUST initiate the Session
immediately after the existing Session is complete and all changes from that
Session have been applied.
 If the Connection Request is not for any CWMP Endpoint currently in Session,
the CPE MAY initiate a new Session with the requested CWMP Endpoint while
the existing Session is still active.
This requirement holds for Connection Requests received any time during the interval
that the CPE considers itself in a Session with at least one CWMP Endpoint,
including the period in which the CPE is in the process of establishing the Session.

November 2013 © The Broadband Forum. All rights reserved. Page 190 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

The CPE MUST ignore an XMPP Connection Request that is neither successfully
validated nor authenticated.

K.2.2 ACS Requirements

An ACS following the requirements of this Annex SHOULD be able to enable the use of
XMPP on a CPE supporting this Annex by configuring an XMPP.Connection object,
configuring the ManagementServer.ConnReqXMPPConn Parameter to reference the
XMPP.Connection object, and optionally configuring the ManagementServer.ConnReq-
AllowedJabberIDs Parameter to contain the list of allowed Jabber IDs that can initiate an
XMPP Connection Request.
An ACS conforming to this Annex MUST have access to an XMPP connection that
adheres to the following requirements:
 Connects to an XMPP Server that is capable of communicating with the CPE that
the ACS intends to issue a Connection Request to.
 Opens an XML Stream to the XMPP Server and accepts an XML Stream from the
XMPP Server as defined in Section 4.2/RFC 6120 [37] and further described in
Appendix III.4.2. Note: XML Streams are unidirectional and this XMPP
Connection Request mechanism requires the use of 2 XML Streams over a single
TCP connection as is recommended in Section 4.5/RFC 6120 [37] for Client to
Server sessions.
 Uses TLS to establish an encrypted and secure TCP connection with the XMPP
Server as defined in Section 5/RFC 6120 [37] (see K.2.2.1 below for XMPP
Connection Request specific details).
 Uses SASL to authenticate with the XMPP Server as defined in Section 6/RFC
6120 [37].
 Sends XMPP Connection Request messages to a CPE supporting this Annex (see
K.2.2.2 below for details).
The details of these functions as they apply to the XMPP Connection Request mechanism
are defined in the following Sections.

K.2.2.1 XMPP Connection Encryption

An ACS following the requirements of this Annex MUST have access to a secure
connection if TLS is considered “mandatory-to-negotiate” for all client-to-server XMPP
connections that are used for XMPP Connection Requests (see K.3 for recommendations
about XMPP Server deployments). If TLS is considered “mandatory-to-negotiate”, then
the XMPP connection is encrypted using the STARTTLS extension of the Transport
Layer Security (TLS) protocol as defined in Section 5/RFC 6120 [37].

K.2.2.2 XMPP Connection Request

An ACS conforming to this Annex MUST send XMPP Connection Request messages via
the XMPP Server that the ACS has access to.

November 2013 © The Broadband Forum. All rights reserved. Page 191 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

The format of the XMPP Connection Request message is defined in Annex K.2.3. An
ACS MUST adhere to the following rules when sending an XMPP Connection Request
message:
 The XMPP Connection Request message MUST be delivered within an XMPP IQ
Stanza across an XML Stream that has been TLS secured, according to Annex
K.2.2.1, and authenticated.
 The XMPP Connection Request message MUST be well-formed XML and
validated against the cwmp-xmppConnReq-1-0.xsd (http://www.broadband-
forum.org/cwmp/cwmp-xmppConnReq-1-0.xsd).
 The “from” address contained within the XMPP IQ Stanza MUST match one of
the addresses contained within the list-based ManagementServer. -
ConnReqAllowedJabberIDs Parameter (unless the value of that Parameter is
empty, which means that all addresses are allowed).
 The value of the “username” element within the “connectionRequest” element
MUST match the value of theManagementServer.ConnectionRequestUsername
Parameter for the CPE where the XMPP Connection Request is being sent.
 The value of the “password” element within the “connectionRequest” element
MUST match the value of the ManagementServer.ConnectionRequestPassword
Parameter for the CPE where the XMPP Connection Request is being sent.

K.2.3 Message Flows

The following figures show example message flows associated with the procedures
defined in Annex K.2.1 and K.2.2 to support Connection Requests to Devices.
In all of the examples, the address uses the notation (L@D/R), where L is the local-part
(XMPP. Connection.{i}.Username), D is the domain-part (XMPP. Connection.{i}.-
Domain), and R is the resource-part (XMPP. Connection.{i}.Resource), where
XMPP.Connection.{i} is the instance referenced by the ManagementServer.ConnReq-
XMPPConn Parameter.

K.2.3.1 Connection Request

The Connection Request message is formatted within an XMPP IQ Stanza and is defined
with the Broadband Forum connectionRequest element as seen in Figure 19. This
element utilizes the existing ConnectionRequestUsername and ConnectionRequest-
Password Parameters contained in the ManagementServer object of the CPE where the
XMPP Connection Request message is addressed. As the XMPP connection is an
encrypted and authenticated channel, there is no need for these values to be further
encrypted.

<iq from="[ACS-identity]" to="L@D/R" id="cr001" type="get">

<connectionRequest xmlns="urn:broadband-forum-org:cwmp:xmppConnReq-1-0">
<username>username</username>
<password>password</password>
</connectionRequest>
</iq>

November 2013 © The Broadband Forum. All rights reserved. Page 192 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Figure 19 – Connection Request: sent from ACS

K.2.3.2 Connection Request Successful Response

A successful response from the XMPP client contained within the CPE is an empty result
IQ Stanza to the ACS as seen in Figure 20.

<iq from="L@D/R" to="[ACS-identity]" id="cr001" type="result" />

Figure 20 – Successful Response to Connection Request: sent from CPE

K.2.3.3 Connection Request Error Response

An unsuccessful response is an error IQ stanza with the associated error type element.
If the CPE is not available, the response from the XMPP Server MUST contain a
<service-unavailable/> error as seen in Figure 21.
If the CPE does not support the “urn:broadband-forum-org:cwmp:xmppConnReq-1-0”
namespace, the response from the CPE MUST contain a <service-unavailable/> error as
seen in Figure 21.

<iq from="L@D/R" to="[ACS-identity]" id="cr001" type="error">

<connectionRequest xmlns="urn:broadband-forum-org:cwmp:xmppConnReq-1-0">
<username>username</username>
<password>password</password>
</connectionRequest>
<error code="503" type="cancel">
<service-unavailable xmlns="urn:ietf:params:xml:ns:xmpp-stanzas" />
</error>
</iq>

Figure 21 – 503 Error Response to Connection Request from ACS

If the XMPP Connection Request cannot be authenticated, the CPE MUST send a <not-
authorized> error as seen in Figure 22.

<iq from="L@D/R" to="[ACS-identity]" id="cr001" type="error">

<connectionRequest xmlns="urn:broadband-forum-org:cwmp:xmppConnReq-1-0">
<username>username</username>
<password>password</password>
</connectionRequest>
<error type="cancel">
<not-authorized xmlns="urn:ietf:params:xml:ns:xmpp-stanzas" />
</error>
</iq>

Figure 22 – Authentication Error Response to Connection Request from ACS

November 2013 © The Broadband Forum. All rights reserved. Page 193 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

K.3 XMPP Server Deployment Requirements

An XMPP Server being used to send XMPP Connection Request messages between an
ACS and a CPE that conform to this Annex MUST adhere to the requirements defined in
XMPP (as defined in RFC 6120 [37]). In addition, it is RECOMMENDED that the
XMPP Servers be configured as follows:
 TLS is “mandatory-to-negotiate” for all client-to-server communications.
 TLS is “mandatory-to-negotiate” for all server-to-server communications.
The configuration recommendations are for environments where the XMPP Servers are
not fully under the control of the Service Provider, which would imply that they are
potentially at risk for security attacks.

K.4 Security Considerations

The following security considerations associated with the procedures defined in this
Annex are identified:
 The XMPP specification describes several security considerations. The reader is
referred to Section 13 of RFC 6120 [37] for a detailed description of these
security considerations and the associated risk.
 Section 13.6 of RFC 6120 [37] requires that XMPP Client and Server
implementations support “strong security”, which refers to the use of security
technologies that provide both mutual authentication and integrity checking, but it
is up to the installed configuration to ensure that these security details are enabled.
Mutual authentication is of particular importance for a secure XMPP Connection
Request mechanism especially for the server-to-server communications.
 In order for the XMPP Connection Request to be considered secure, the ACS
MUST configure the allowed list of Jabber ID from addresses (the
ManagementServer.ConnReqAllowedJabberIDs Parameter) and the XMPP
Connection Request authentication credentials (the ConnectionRequestUsername
and ConnectionRequestPassword Parameters on the ManagementServer Object)
during an SSL/TLS secured CWMP Session.

November 2013 © The Broadband Forum. All rights reserved. Page 194 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Annex L. CPE standby-related

behaviors

L.1 Introduction
Some CPE have the capability to enter a standby state where some of their functions are
not available or not available immediately. The decision to enter or leave standby is
independent from CWMP, but the CPE has to behave in a consistent way when dealing
with the ACS. This Annex describes how to achieve this.
The relevant use cases are:
a. If a CPE goes into standby, misses at least one Scheduled or Periodic Contact with
the ACS, then wakes up, the ACS has a way to be informed of the fact that the CPE is
available again. The ACS has some control on the timeliness of that information. The
ACS is also able to decide if it is interested in the information or not.
b. If a CPE goes into standby and then wakes up after the ACS failed to get a response
to a Connection Request, the ACS has a way to be informed of the fact that the CPE
is available again. The ACS has some control on the timeliness of that information.
The ACS is also able to decide it is not interested in that information.
c. If a CPE goes into standby and none of the above situations is true, there is no need to
inform the ACS when the CPE is available again, because it has not been Seen
Missing.
d. If, for some reason, the ACS would not want the CPE to miss any Periodic Contact
for a period of time, the ACS is able to determine whether the CPE offers control on
that behavior and, if so, to configure it as necessary. Whenever the ACS requests a
Scheduled Contact, it does not want the CPE to miss it.
e. If, for some reason, the ACS would not want the CPE to be unreachable by
Connection Requests for a period of time, the ACS is able to determine whether the
CPE offers control on that behavior and, if so, to configure it as wanted.
f. The ACS is able to distinguish between a CPE that reboots and a CPE that wakes up
from standby.
g. Standby modes are implemented to improve energy efficiency; their use does not
result in an increased activity of the CPE and/or the ACS.

November 2013 © The Broadband Forum. All rights reserved. Page 195 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

L.2 Procedures
L.2.1 Use of WAKEUP Event
A specific Event allows the CPE to indicate to the ACS that it is sending an Inform as a
result of waking up from a standby state. This Event is “13 WAKEUP”. This addresses
use case f.
A CPE SHOULD NOT issue a BOOT Event when a WAKEUP Event is appropriate,
because a BOOT Event is likely to trigger a heavier procedure on the ACS, which would
go against use case g.

L.2.2 Conditions requiring a WAKEUP Event

Three parameters are defined in the data model as policy elements that can be set by the
ACS. They allow the CPE to decide when it has to send a WAKEUP Event. (For those
which are thresholds, a negative value indicates the CPE MUST NOT issue a WAKEUP
for exceeding that threshold.)
 A CPE waking up from a non CR-Aware Standby that lasted more than
CRUnawarenessMaxDuration MUST issue a WAKEUP Event (use case b).
 A CPE waking up from a non fully Timer-Aware Standby that made it miss more
than MaxMissedPeriodic Periodic Contacts MUST issue a WAKEUP Event (use case
a).
 A CPE waking up from a non fully Timer-Aware Standby that made it miss at least
one Scheduled Contact MUST issue a WAKEUP Event if NotifyMissedScheduled is
true (use case a).
 A CPE which is not in one of the above situations MUST NOT issue a WAKEUP
Event (use case c).

L.2.3 When to deliver a WAKEUP Event

The CPE MUST deliver the WAKEUP Event as soon as one of the conditions in L.2.2 is
met, issuing a specific Inform for that purpose if needed. If several conditions apply,
only one event summarizing these conditions is sent.

L.2.4 Management of standby modes by the ACS

Two capability parameters allow the CPE to advertise the fact that it is able to wake up
based on network activity or internal timers. Three policy elements allow the ACS to
require the CPE to remain in CR-Aware Standby or to honor Periodic or Scheduled
Contacts:
 If NetworkAwarenessCapable is true and the ACS sets CRAwarenessRequested to
true, the CPE MUST NOT go into a non CR-Aware Standby state (use case e).
 If SelfTimerCapable is true and the ACS sets PeriodicAwarenessRequested to true,
the CPE MUST NOT miss any Periodic Contact (use case d).

November 2013 © The Broadband Forum. All rights reserved. Page 196 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

 If ScheduledAwarenessRequested is true, the CPE MUST NOT miss any Scheduled

Contact (use case d). This holds even if SelfTimerCapable is false; in that case the
CPE will not go into standby at all until all Scheduled Contacts have been honored.

November 2013 © The Broadband Forum. All rights reserved. Page 197 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Annex M. UDP Lightweight

Notification

M.1 Introduction
The procedures defined in this Annex extend the CPE WAN Management Protocol to
allow for a UDP-based notification mechanism. This “lightweight” mechanism is only
applicable if the service provider does not require reliability of packet delivery. In
general, UDP usage in IP networks is reliable, i.e. the packet loss probability is low.
Service providers might want to use this method for historical trend analysis of non-
sensitive data.
This UDP lightweight notification mechanism is not intended as a replacement of the
existing Inform mechanism but as an alternative to the current Active and Passive
notification mechanism.

M.2 Procedures
M.2.1 CPE requirements
A CPE conforming to this Annex indicates support of the UDP lightweight notification
mechanism by setting the capability Parameter ManagementServer.Lightweight-
NotificationSupported to true. If this Parameter is missing or set to false the mechanism
is not supported by the CPE.
CPE supporting this mechanism MUST send the UDPLightweightNotification message
whenever a change occurs in the value of a parameter (or parameters), that the ACS has
marked for “Active lightweight notification” (value 5 or 6) via the
SetParameterAttributes method, by an external cause (a cause other than the ACS itself).
The CPE MUST include the new value (or values) as a ParameterStruct in the associated
UDPLightweightNotification message. The calling arguments for this message are
described in Table 108 below.
A UDPLightweightNotification message MUST be sent to the appropriate address as
defined by ManagementServer Parameters. The host name or IP address is extracted
from the ManagementServer.UDPLightweightNotificationHost Parameter, and the port
number is taken from the ManagementServer.UDPLightweightNotificationPort
Parameter. If these Parameters are not implemented then the destination host MUST be
be the ACS (using the pre-determined ACS address - see section 3.1), and the destination
port MUST be 7547, which has been assigned by IANA for the CPE WAN Management
Protocol (see [17]).

November 2013 © The Broadband Forum. All rights reserved. Page 198 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

The message MUST be transmitted within a single UDP packet.

Note – The UDP packet includes several headers that are not under the direct control of the
application, i.e. HTTP headers, IP header (IPv4 or IPv6) and UDP header. Also, the
application cannot know whether the packet will be fragmented somewhere between its source
and destination. Therefore, for a given deployment, it might be necessary to apply a heuristic
algorithm when determining the maximum message length.

M.2.2 ACS requirements

The ACS MUST ignore a UDPLightweightNotification that is not successfully validated
and authenticated.
A UDPLightweightNotification message is validated if and only if it conforms to the
requirements in M.2.3 and the following requirements are met:
 The Timestamp MUST be greater than or equal to the Timestamp value for the
UDP Lightweight Notification message that had been most recently received,
validated, and authenticated.
 The Username MUST match the value of the ManagementServer.Username
parameter.
A UDPLightweightNotification message is authenticated if and only if the following
requirements are met:
 The Signature given by the value of the “Signature” HTTP header MUST match
the value of the signature locally computed by the ACS following the procedure
specified in section M.2.3 using the local value of the
ManagementServer.Password Parameter.
The following additional requirements relate to Timestamp processing:
 To allow the above comparison to be made, the ACS MUST maintain a persistent
record of the Timestamp value of the most recent UDP Lightweight Notification
that was successfully validated and authenticated. The Timestamp value for any
UDP Lightweight Notification message that fails to be validated or authenticated
MUST NOT be recorded.
 The ACS MAY place stricter requirements on the Timestamp than stated above.
The ACS MAY, for example, additionally verify that the Timestamp is within a
time window relative to its understanding of the current time. If a ACS chooses to
do this, it SHOULD avoid making the time window too narrow, in order to allow
for a reasonable margin of error in both the ACS and CPE.

M.2.3 UDPLightweightNotification message

The UDPLightweightNotification message MUST conform to the following
requirements:
 It MUST be a valid HTTP 1.1 POST message as defined in [6].
 The HTTP message body MUST contain a valid XML structure containing the
message arguments defined in M.2.4 coded according to the defined schema
(see M.2.5).

November 2013 © The Broadband Forum. All rights reserved. Page 199 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

 The request URL MUST be set to the root path “/”.

 The message MUST include the following HTTP headers, and any other HTTP
headers MUST NOT be included:
o Host
o Content-Type (with the value of “text/xml; charset=utf-8”)
o Content-Length
o Signature
 The signature header contains the 40-character hexadecimal representation (case
insensitive) of HMAC-SHA1 (Key, Text) [19] where:
o “Key” is the value of the parameter ManagementServer.Password as read
from the CPE.
o “Text” is the whole message body (i.e., not including the headers or empty
line), treated as a sequence of octets.
 The message body MUST be UTF-8 encoded.

M.2.4 Message arguments

The calling arguments for the UDPLightweightNotification message are defined in Table
108. There is no response message associated with the message.

Table 108 – UDPLightweightNotification arguments

Argument Type Value
TS int Timestamp. The number of seconds since the Unix epoch until the time the
message is created (the standard Unix timestamp).
UN string(256) Username: The value of the parameter ManagementServer.Username as read
from the CPE.
CN string Cnonce: A random string chosen by the CPE.
OUI string(6) Organizationally unique identifier of the device manufacturer. Represented as
a six hexadecimal-digit value using all upper-case letters and including any
leading zeros. The value MUST be a valid OUI as defined in [10]. The value
MUST be the same as the value of the DeviceInfo.ManufacturerOUI
Parameter.
ProductClass string(64) Identifier of the class of product for which the serial number applies. That is,
for a given manufacturer, this Parameter is used to identify the product or class
of product over which the SerialNumber Parameter is unique. The value
MUST be the same as the value of the DeviceInfo.ProductClass Parameter.
SerialNumber string(64) Identifier of the particular device that is unique for the indicated class of
product and manufacturer. The value MUST be the same as the value of the
DeviceInfo.SerialNumber Parameter.
Param ParameterStruct… A structure with the name and value of the parameters notified, defined in
Table 109. This element can be repeated n times, depending on the number of
parameters to be notified in the same message.
There MUST be at least one structure in the message, but there can be up to
n structures in the same message until the maximum length of the message is
reached.

November 2013 © The Broadband Forum. All rights reserved. Page 200 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Table 109 – ParameterStruct definition

Argument Type Value
Name string(256) This is the name of a Parameter. The CPE MUST treat the Parameter name as
case sensitive.
Value anySimpleType This is the value of the Parameter. The CPE MUST treat string-valued
Parameter values as case-sensitive. The rules regarding the anySimpleType
data type, contained in Table 12, MUST be applied..
Note: The defined values are derived from the ParameterValueStruct structure in Table 17.

M.2.5 UDPLightweightNotification XML Schema

The XML schema, which is the normative definition of the UDPLightweightNotification
message format, is specified in the referenced file below:
Version Namespace XSD
1.0 urn:broadband-forum- http://www.broadband-
org:cwmp:lwnotif-1-0 forum.org/cwmp/UDPLightweightNotification-1-0.xsd

M.2.6 UDPLightweightNotification example

As explained in M.2.4 the UDPLightweightNotification message is sent using the HTTP
POST message. An example is given below.
POST / HTTP/1.1
Host: acs.server.com
Content-Type: text/xml; charset=utf-8
Content-Length: length
Signature: 42A424FB0C4938BBF08259514C64ABFC1E74C61F

<?xml version="1.0" encoding="UTF-8"?>

<Notification xmlns="urn:broadband-forum-org:cwmp:lwnotif-1-0"
xmlns:xs="http://www.w3.org/2001/XMLSchema"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="urn:broadband-forum-org:cwmp:lwnotif-1-0 http://www.broadband-
forum.org/cwmp/¬cwmp-UDPLightweightNotification-1-0.xsd">
<TS>1120673700</TS>
<UN>ACS57689</UN>
<CN>XTGRWIPC6D3IPXS3</CN>
<OUI>00D09E</OUI>
<ProductClass></ProductClass>
<SerialNumber>134SS03013</SerialNumber>
<Param>
<Name>Device.ManagementServer.PeriodicInformEnable</Name>
<Value xsi:type="xs:boolean">false</Value>
</Param>
<Param>
<Name>Device.ManagementServer.PeriodicInformInterval</Name>
<Value xsi:type="xs:unsignedInt">60</Value>
</Param>
</Notification>

November 2013 © The Broadband Forum. All rights reserved. Page 201 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Appendix I. CPE Proxier

Implementation
Guidelines

I.1 Introduction
This Appendix suggests possible implementation guidelines and mechanisms to assist a
CPE Proxier to provide CMWP Proxy Management of a Proxied Device connected via a
Proxy Protocol. Proxy Protocols supported by a CPE Proxier could be synchronous,
asynchronous, IP based, non-IP based, standard, or proprietary.
The CPE Proxier that supports a Proxy Protocol(s) supports the underlying
communications protocol and capabilities to communicate via the Proxy Protocol. The
CPE Proxier also supports the mechanisms needed to discover and manage the Proxied
Devices via the Proxy Protocol.
To provide support for a varying number of Proxy Protocols this Appendix suggests
mechanisms to enable this. Some paradigms are shared by both the Virtual CWMP
Device and Embedded Object Mechanisms; these are covered in Section I.2. For
guidelines specific to Embedded Object Mechanism see Section I.3, for the Virtual
CWMP Device see Section I.4. Section I.5 is used to provide an example of how the Data
Model extensions mentioned in Annex J are used.
I.2 Common Guidelines for the Virtual CWMP Device and
Embedded Object Mechanisms
All of the guidelines in this section apply to both the Virtual CWMP Device and the
Embedded Object Mechanisms proxying of CWMP RPC commands.

I.2.1 Unsupported CWMP RPC Commands by the Proxy Protocol

The CWMP supports an AccessList attribute that might not be supported by a Proxy
Protocol. If the Proxy Protocols cannot support such a mechanism, and the ACS attempts
to modify the AccessList attribute to any other value, the CPE could choose to reject the
modification using a SOAP fault '9001' Request denied.

I.2.2 Support for Proxy Protocol Methods with no Matching RPC

Proxy Protocols might use a separate method call for various functions such as Ping,
TraceRoute, and GetDeviceStatus etc. For these operations CWMP uses the Data Model
to perform such functions (not an RPC). The suggested solution is to have the CPE

November 2013 © The Broadband Forum. All rights reserved. Page 202 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Proxier use the Data Model (as defined in the DT instance(s); see Annex B/TR-106 [13])
to model the particular method.
Here is an example of how a CWMP TraceRoute Diagnostics test that is defined in [32]
would map to the UPnP DM TraceRoute Service:
1. The ACS via CWMP SetParameterValues sets the appropriate Parameter values
for test setup in the TraceRoute Object, and then sets the
TraceRoute.DiagnosticsState to Requested.
2. Next the CPE Proxier initiates a UPnP TraceRoute service request to the Proxied
Device, using the appropriate Parameters from the TraceRoute Object.
3. The CPE Proxier receives notification of the completion of the TraceRoute
diagnostic (either through UPnP notifications from the Proxied Device or polling
the Proxied Device).
4. Using the GetTraceRouteResult service the CPE Proxier retrieves the TraceRoute
diagnostic results from the Proxied Device. These results are stored in the CPE
Proxier for future retrieval from the ACS.
5. The CPE Proxier will send a CWMP Event "8 DIAGNOSTICS COMPLETE" in
a CWMP Inform to the ACS upon the completion of the test.

I.2.3 Support for Transactional Integrity

To provide the transactional integrity requirement in Section 3.7.1.1, during the course of
a Session the CPE Proxier might need to return the requested value of any Parameter that
was set previously within the same Session. The CPE Proxier could use the requested
value from a previous configuration command in the same Session, rather than retrieving
a new (and possibly modified) value for the later request within the same CWMP
Session.
I.3 Embedded Object Mechanism
The following guidelines are for a CPE Proxier when using the Embedded Object
Mechanism.

I.3.1 Device Discovery

Proxy Protocols have various mechanisms for discovering devices. Some require polling
or listening on a particular TCP port, others might need an API to the supported Proxy
Protocols.
When using the Embedded Object Mechanism the CPE Proxier will only support a
Proxied Device that is represented in a DeviceInfo.SupportedDataModel DT entry(s).
When a Device is initially discovered by the CPE Proxier the following steps occur.
 Retrieve the information from the discovered device, via the Proxy Protocol, that
is necessary to match and verify that the discovered device is supported by the
CPE Proxier.

November 2013 © The Broadband Forum. All rights reserved. Page 203 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

 If the discovered device is supported, The CPE Proxier could populate the
appropriate Data Model Object and Parameters based on the information retrieved
from the device utilizing the appropriate methods of the Proxy Protocol.
 The CPE Proxier would then update the ManagementServer.EmbeddedDevice
table to reference the DeviceInfo.SupportedDataModel table DT entry for the
Proxied Device and also reference the newly created Data Model Object.
For the ACS to discover the device, it can utilize the
ManagementServer.EmbeddedDeviceNumberOfEntries Parameter or the number of
entries Parameter for the particular Object representing the device (possibly setting a
change notification on either Parameter for notification of the newly discovered Proxied
Device).

I.3.2 CPE Proxier use of Polling

Polling could be used by the CPE Proxier to support change notifications for Parameters
on the Proxied Device, if a Proxy Protocol does not support such a mechanism.
The CPE Proxier might also utilize polling of Parameter values on the Proxy Protocol to
keep the cached Objects and Parameters 'in sync' with the Proxied Device, and upon
change send the appropriate CWMP notification.

I.3.3 ACS Query of RPC Execution

When the ACS requests Parameter values from the CPE Proxier it could query the
ManagementServer.EmbeddedDevice.{i}.LastSyncTime Parameter to insure the validity
of the data. When the ACS receives a committed response from the CPE Proxier for a
configuration command, it could request the
ManagementServer.EmbeddedDevice.{i}.CommandProcessed Parameter to verify the
state of the command.

I.3.4 Support for Proxy Protocol Methods Reboot and Download

For a Proxied Device that might not fit the criteria for a Virtual CWMP Device, yet
supports a Reboot command or Download feature, an Embedded Object mechanism can
be used. The methods can be supported via Data Model Objects and Parameters that
function similar to the TraceRoute example above (Section I.2.2) and other Data Model
mechanisms (as defined in the DT instance(s); see Annex B/TR-106 [13]).
The Download feature for example, which would typically be used to perform a firmware
upgrade, could be modeled within the object that represents the Embedded Device. The
following Parameters could be used to perform a Download to that Proxied Device:
URL: This is where the file to be downloaded resides.
Username: The username to be used when accessing the URL.
Password: The password to be used when accessing the URL.
StartDownload: A command parameter that when set to true causes the download to
begin.

November 2013 © The Broadband Forum. All rights reserved. Page 204 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Status: The results of the download represented as an enumerated string

(NOT_STARTED, PENDING, SUCCESS, FAILED).
ErrorMessage: An empty string unless Status is FAILED, in which case this would
be a description of why the Download failed.
I.4 Virtual CWMP Device Mechanism
The following guidelines are for a CPE Proxier when using the Virtual CWMP Device
Mechanism.

I.4.1 Device Discovery

Proxy Protocols have various mechanisms for discovering devices. Some require polling
or listening on a particular TCP port, others might need an API to the supported Proxy
Protocols.
The Virtual CPE Device reflects the Data Model it supports in its own
DeviceInfo.SupportedDataModel DT entry.
When a Device is initially discovered by the CPE Proxier the following steps occur.
 Retrieve the information from the discovered device, via the Proxy Protocol, that
is necessary to match and verify that the discovered device is supported by the
CPE Proxier.
 When a CPE Proxier first discovers a device that it supports, the CPE Proxier
represents the Proxied Device and connects to the ACS (as any new device would
when it connects to the ACS for the first time) by sending a BOOTSTRAP event
(described in Table 39).
 Update the ManagementServer.VirtualDevice table in the CPE Proxier.

I.4.2 Request for Session Timeout Extension

One aspect of all Proxy Protocols is the turnaround time. A single Proxy Protocol
command might exceed the CMWP turnaround time. A synchronous CWMP command
could also result in multiple Proxy Protocol transactions or asynchronous transactions to
complete, which increases the number of operations subject to the Proxy Protocol timeout
within the CWMP Session timeout.
Figure 23 is an example of how the CWMP turnaround time might exceed the CWMP
Session timeout due to the additional Proxy Protocol processing time.
To provide an indication to this condition, the CPE Proxier has the option of notifying the
ACS with the "SessionTimeout" Inform SOAP header (defined in Table 4) requesting to
extend the Session timeout. Additionally a Virtual CWMP Device would use the
"SessionTimeout" value in cases where an operation failed to complete in the previous
Session due to a timeout.

November 2013 © The Broadband Forum. All rights reserved. Page 205 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Figure 23 – Turnaround time

I.4.3 CPE Proxier use of Caching

Caching by the CPE Proxier can provide a mechanism to store information and provide
CWMP services (Attributes, Notifications) that are otherwise not supported by the Proxy
Protocol.
Below are CWMP mechanisms that might use caching and polling in order to support a
Proxy Protocol mechanism that cannot be relayed. It is not suggested to use the cache for
returning values and setting values to the Proxied Device without attempting to reach the
device first. CWMP Proxying is predicated on the relaying of commands within the
CWMP Session as shown in Figure 23.
 Device discovery information
If the CPE Proxier has the capability to retain Proxied Device specific
information such that when the device is rediscovered (possibly with a new
network address) it will appear to be the same Device as when it was initially
discovered, the ACS will be able to manage the Proxied Device as the same
device instead of managing it as a new device.
 Single CWMP RPC results in multiple Proxy Protocol RPCs
Caching might be used in the case where a single CMWP RPC results in
multiple Proxy Protocol method calls. This allows the CPE Proxier to retain
information from each call and supply the single RPC response when finished.

November 2013 © The Broadband Forum. All rights reserved. Page 206 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

For example, a GetParameterNames RPC call with NextLevel=false would

result in two UPnP DM commands GetSupportedParameters and GetInstances
to respond to the single GetParamenterNames call.
Another example would be a SetParameterValues RPC call to a CPE Proxier
that supports an asynchronous Proxy Protocol that requires a set command and
a separate get command to verify the set operation is complete.
 Support for unsupported CWMP mechanisms
A Proxy Protocol that does not support Attributes and Notifications might
need the CPE Proxier to utilize caching of the Attributes and Notification
requests.
The CPE Proxier might use polling to keep cached Objects and Parameters ‘in
sync’ with the Proxied Device, and upon change send the appropriate CWMP
notification.
A Proxy Protocol that does not have a matching ‘Reboot’ command might
need the CPE Proxier to utilize similar Proxy Protocol commands to interpret
the Reboot request.

I.4.4 Virtual CWMP Device Error Scenarios

The Virtual CWMP Device utilizes connectivity between the CPE Proxier and the ACS,
and the CPE Proxier and the Proxied Device (see Figure 16). In this situation there are
two communication links that are needed to complete the RPC operation. Failure of
either of these communication links might result in a CMWP Session fault, and will
require the Virtual CWMP Device to follow the session retry logic in Section 3.2.1.1.

November 2013 © The Broadband Forum. All rights reserved. Page 207 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

I.5 Proxy Management Support Example

This is an example of a CPE Proxier that incorporates a Virtual CWMP Device
Mechanism and Embedded Object Mechanism (utilizing Root and Service Objects). The
following figure describes a Router that is also a CPE Proxier device that supports
multiple Proxied Devices.
The NAS 1 and 2 are Proxied Devices that are supported by the Router device via the
Virtual CWMP Device Mechanism.
Utilizing the Embedded Object Mechanism the Router device supports the Meter Devices
1 and 2 via a Proxied Device table “Device.Meter.{i}.” with 2 entries that exist in the
Router Data Model. The Router supports IP cameras 1 and 2 as Proxied Devices utilizing
the “Device.Services.IPCamera.{i}” service Objects.

Figure 24 – Router supporting 6 Proxied Devices

Data Models; The ACS sees 3 Devices, a Router, NAS #1 and NAS #2:
Router
Device.DeviceInfo (DeviceInfo for the Router)
Device.DeviceInfo.SupportedDataModel.1.URL = RouterDevice URL
Device.DeviceInfo.SupportedDataModel.2.URL = IPCamera URL
Device.DeviceInfo.SupportedDataModel.3.URL = Meter URL
Device.ManagementServer.VirtualDevice.1.SerialNumber = (NAS #1 Serial Number)
Device.ManagementServer.VirtualDevice.1.ManufacturerOUI = (NAS #1 Manufacturer OUI)
Device.ManagementServer.VirtualDevice.1.ProductClass = (NAS #1 Product Class)
Device.ManagementServer.VirtualDevice.1.Host = (NAS #1 Host table entry)
Device.ManagementServer.VirtualDevice.1.ProxyProtocol = UPnP-DM
Device.ManagementServer.VirtualDevice.2.SerialNumber = (NAS #2 Serial Number)
Device.ManagementServer.VirtualDevice.2.ManufacturerOUI = (NAS #2 Manufacturer OUI)
Device.ManagementServer.VirtualDevice.2.ProductClass = (NAS #2 Product Class
Device.ManagementServer.VirtualDevice.2.Host = (NAS #2 Host table entry)
Device.ManagementServer.VirtualDevice.2.ProxyProtocol = UPnP-DM
Device.ManagementServer.ConnectionRequestURL = http://<IP>:8080/connreq
Device.ManagementServer.EmbeddedDevice.1.ControllerID = IP1
Device.ManagementServer.EmbeddedDevice.1.ProxiedDeviceID = 1
Device.ManagementServer.EmbeddedDevice.1.Reference = Device.Services.IPCamera.1
Device.ManagementServer.EmbeddedDevice.1.SupportedDataModel=Device.DeviceInfo.SupportedDataModel.2
Device.ManagementServer.EmbeddedDevice.1.Host = (IP Camera #1 in Host table)

November 2013 © The Broadband Forum. All rights reserved. Page 208 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Device.ManagementServer.EmbeddedDevice.1.ProxyProtocol = X_00256D_CamP
Device.ManagementServer.EmbeddedDevice.1.LastSyncTime = (last time the device was synced)
Device.ManagementServer.EmbeddedDevice.1.CommandProcessed = (state of last command)
Device.ManagementServer.EmbeddedDevice.2.ControllerID = IP1
Device.ManagementServer.EmbeddedDevice.2.ProxiedDeviceID = 2
Device.ManagementServer.EmbeddedDevice.2.Reference = Device.Services.IPCamera.2
Device.ManagementServer.EmbeddedDevice.2.SupportedDataModel=Device.DeviceInfo.SupportedDataModel.2
Device.ManagementServer.EmbeddedDevice.2.Host = (IP Camera #2 in Host table)
Device.ManagementServer.EmbeddedDevice.2.ProxyProtocol = X_00256D_CamP
Device.ManagementServer.EmbeddedDevice.2.LastSyncTime = (last time the device was synced)
Device.ManagementServer.EmbeddedDevice.2.CommandProcessed = (state of last command)
Device.ManagementServer.EmbeddedDevice.3.ControllerID = ZW1
Device.ManagementServer.EmbeddedDevice.3.ProxiedDeviceID = 1
Device.ManagementServer.EmbeddedDevice.3.Reference = Device.Meter.1
Device.ManagementServer.EmbeddedDevice.3.SupportedDataModel=Device.DeviceInfo.SupportedDataModel.3
Device.ManagementServer.EmbeddedDevice.3.Host = (Meter #1 in Host table)
Device.ManagementServer.EmbeddedDevice.3.ProxyProtocol = Z-Wave
Device.ManagementServer.EmbeddedDevice.3.LastSyncTime = (last time the device was synced)
Device.ManagementServer.EmbeddedDevice.3.CommandProcessed = (state of last command)
Device.ManagementServer.EmbeddedDevice.4.ControllerID = ZW1
Device.ManagementServer.EmbeddedDevice.4.ProxiedDeviceID = 2
Device.ManagementServer.EmbeddedDevice.4.Reference = Device.Meter.2
Device.ManagementServer.EmbeddedDevice.4.SupportedDataModel=Device.DeviceInfo.SupportedDataModel.3
Device.ManagementServer.EmbeddedDevice.4.Host = (Meter #2 in Host table)
Device.ManagementServer.EmbeddedDevice.4.ProxyProtocol = Z-Wave
Device.ManagementServer.EmbeddedDevice.4.LastSyncTime = (last time the device was synced)
Device.ManagementServer.EmbeddedDevice.4.CommandProcessed = (state of last command)
Device.Services.IPCamera.1
Device.Services.IPCamera.2
Device.Meter.1
Device.Meter.2

NAS #1
Device.DeviceInfo (DeviceInfo for the NAS #1)
Device.DeviceInfo.SupportedDataModel.1.URL = Device URL
Device.DeviceInfo.SupportedDataModel.2.URL = StorageService URL
Device.ManagementServer.ConnectionRequestURL = http://<IP>:8080/connreq-nas1
Device.ProxierInfo.SerialNumber = (Router Serial Number)
Device.ProxierInfo.ManufacturerOUI = (Router Manufacturer OUI)
Device.ProxierInfo.ProductClass = (Router Product Class)
Device.ProxierInfo.ProxyProtocol = UPnP-DM
Device.Services.StorageService.1

NAS #2
Device.DeviceInfo (DeviceInfo for the NAS #2)
Device.DeviceInfo.SupportedDataModel.1.URL = Device URL
Device.DeviceInfo.SupportedDataModel.2.URL = StorageService URL
Device.ManagementServer.ConnectionRequestURL = http://<IP>:8080/connreq-nas2
Device.ProxierInfo.SerialNumber = (Router Serial Number)
Device.ProxierInfo.ManufacturerOUI = (Router Manufacturer OUI)
Device.ProxierInfo.ProductClass = (Router Product Class)
Device.ProxierInfo.ProxyProtocol = UPnP-DM
Device.Services.StorageService.1

November 2013 © The Broadband Forum. All rights reserved. Page 209 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Appendix II. Alias-Based Addressing

Mechanism – Theory of
Operations

II.1 Introduction
This Appendix describes extensions to CPE WAN Management Protocol to allow for the
OPTIONAL CPE Alias-Based Addressing Mechanism (defined in Section 3.6.1) for
Multi-Instance Objects. This mechanism provides:
 Uniform Object identification across devices.
 Direct Object addressing using uniform identifiers.
 Ability to configure CPEs with less interrogation, including Object instance
auto-creation.
The Alias-Based Addressing Mechanism provides an optional alternative to exclusively
using the Instance Number based addressing. A CPE which supports the Alias-Based
Addressing Mechanism can indicate this capability to the ACS, which can leverage it.
The Alias-Based Addressing Mechanism is provided to improve the end-to-end system
scalability and robustness by allowing the ACS more direct control over how Objects are
referenced during configuration or other management activities.
II.2 Multi-Instance Objects Definition
Multi-Instance Objects are designated in TR-069 Data Model documents with the “{i}”
moniker. For example, TR-181 Issue 2 [32] defines an Object “Device.IP.Interface.{i}.”
and two of its Parameter names are: Name and Status.
Two IP Interface Objects and their Parameters, using Instance Numbers, might look as
follows:
Device.IP.Interface.5.Name = “eth0”
Device.IP.Interface.5.Status = “Disabled”
Device.IP.Interface.30.Name = “fw0”
Device.IP.Interface.30.Status = “Disabled”
In the above example, the CPE has two Objects whose CPE assigned Instance Numbers
are 5 and 30.
The Alias-Based Addressing Mechanism offers an alternative to use text of the ACS’s
choosing in place of Instance Numbers.

November 2013 © The Broadband Forum. All rights reserved. Page 210 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

The same IP Interface Objects’ Parameters, using Instance Aliases, might look as
follows:
Device.IP.Interface.[wan].Name = “eth0”
Device.IP.Interface.[wan].Status = “Disabled”
Device.IP.Interface.[vpn].Name = “fw0”
Device.IP.Interface.[vpn].Status = “Disabled”
In above example, the CPE has two Objects whose ACS-assigned Instance Aliases are
wan and vpn.
II.3 Instance Alias as a Data Model Parameter
In addition of its use within a Path Name to identify Object instances, an Alias is also a
non-functional unique key Parameter. Therefore, an Alias Parameter can be handled as an
ordinary TR-069 Parameter. For example, the following Path Name would return the
value of Instance Alias Parameter if used with GetParameterValues RPC:
Device.IP.Interface.5.Alias
The Instance Alias can also be modified as a unique key on the referenced Object
instance using a SetParameterValues.
For example using the Number-Based Addressing:
Device.IP.Interface.5.Alias = “lan”
or using the Alias-Based Addressing:
Device.IP.Interface.[wan].Alias = “lan”
II.4 Multi-Instance Object Creation
Object instances may come into being by one of the following ways:
 They might exist in CPE firmware, based on factory default configuration.
 If writeable they might be created on request of the ACS.
 They might be created by the CPE when it performs local functions such as
configuration via local web UI, DHCP client discovery, Wi-Fi client discovery,
alarm records, etc.
When the ACS needs to create a new Object instance, the CPE provides one via
AddObject RPC. The CPE assigns a unique unpredictable Instance Number and
subsequently the ACS has to refer to the created Object instance using the Instance
Number assigned by the CPE.
With the Alias-Based Addressing Mechanism, the ACS can choose the Instance Alias
that will be assigned to the Object instance at the time of its creation via
SetParameterValues or AddObject RPC’s. The ACS can then use the Instance Alias
instead of the Instance Number to subsequently address the created Object instance.
With the Alias-Based Addressing Mechanism, the CPE is responsible for providing a
unique Instance Alias in cases where it is not provided upon creation.

November 2013 © The Broadband Forum. All rights reserved. Page 211 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

When a CPE creates a unique random Instance Alias, unlike the Instance Number the
ACS can choose to modify the Instance Alias.
The Alias-Based Addressing Mechanism allows an ACS to choose a uniform naming
mechanism for a particular Object to be used across multiple CPE devices such that they
may be accessed using the same Instance Alias.
II.5 AddObject RPC Extension
The Alias-Based Addressing support extends the AddObject RPC to allow assigning an
Instance Alias to the new Object instance during its creation using the Instance Alias
notation (enclosed between square brackets) following the Path Name.
For example, if an AddObject RPC includes the Path Name Device.IP.Interface.1.IPv6-
Address.[ACS Assigned Instance Alias]., then the CPE would perform the following:
 Create a new Object instance identified by Device.IP Interface.1.IPv6Addr-
ess.{CPE Assigned Instance Number} and Device.IP.Interface.1.IPv6Addr-
ess.[ACS Assigned Instance Alias].
 The Parameter Device.IP.Interface.1.IPv6Address.{CPE Assigned Instance
Number}.Alias is set to “ACS Assigned Instance Alias”.
 The {CPE Assigned Instance Number} is returned to the ACS.
Subsequently the created Object instance and its Parameters are addressable as follows:
 By its Instance Number: Device.IP.Interface.1.IPv6Address.{CPE Assigned
Instance Number}.*
 Or by its Instance Alias: Device.IP.Interface.1.IPv6Address.[ACS Assigned
Instance Alias].*
II.6 Auto-Creation of Object Instances
If the ACS wants to modify a Parameter on an Object instance but does not know if the
Object instance exists, it needs to query the CPE for the Object instance. If the Object
instance does not exist, the ACS creates the Object instance with an AddObject RPC and
then modifies the Parameter via a SetParameterValue command.
With the Alias-Based Addressing Mechanism enabled, and the Auto-Create Instance
Mechanism enabled via the ManagementServer.AutoCreateInstances Parameter
(described in Section A.3.2.1), the ACS can call a SetParameterValue for a Parameter in
the Object instance using an Instance Alias in the Parameter Path Name. If the Object
instance matching the Instance Alias does not exist, it will be created via the Auto-Create
Instance Mechanism and the Parameter value is set.
The Alias-Based Addressing Mechanism saves time and resources both on the ACS and
CPE, by avoiding the query of the CPE, as well as the additional round trip for each
called RPC.
For example, if the Path Name Device.IP.Interface.1.IPv6Address.[ACS Assigned
Instance Alias].IPAddress is used with SetParameterValues RPC to set the value “X”,
these actions would result:

November 2013 © The Broadband Forum. All rights reserved. Page 212 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

 If does not already exist a new Object instance identified by Device.IP.-

Interface.1.IPv6Address.{CPE Assigned Instance Number} or Device.IP.-
Interface.1.IPv6Address.[ACS Assigned Instance Alias] is created.
 The Parameter Device.IP.Interface.1.IPv6Address.{CPE Assigned Instance
Number}.Alias is set to “ACS Assigned Instance Alias”,
 The Parameter Device.IP.Interface.1.IPv6Address.{CPE Assigned Instance
Number}.IPAddress is set to “X”.
II.7 Support for Alias-Based Addressing Mechanism
The CPE informs the ACS of its support for the Alias-Based Addressing Mechanism by
using the ManagementServer.AliasBasedAddressing Parameter (set to true) within the
Inform RPC.
If the ManagementServer.AliasBasedAddressing Parameter is absent in the Inform
Parameters or its value set to false, The CPE will not provide the Alias-Based Addressing
Mechanism.
If the ACS does not support the Alias-Based Addressing Mechanism it ignores the
ManagementServer.AliasBasedAddressing received Parameter.
If the ACS supports the Alias-Based Addressing Mechanism it can use the Alias-Based
Addressing associated Parameters only if the CPE has previously advertised support for
this by providing the Device.ManagementServer.AliasBasedAddressing Parameter in the
Inform.

November 2013 © The Broadband Forum. All rights reserved. Page 213 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Appendix III. XMPP Connection –

Theory of Operations

III.1 Introduction
This Appendix describes a Theory of Operations around the XMPP.Connection table
defined in tr-157-1-8.xml [38], which can be used by a CPE to communicate with an
XMPP Server. One such use of this XMPP Connection Object and this type of
communications is to facilitate the XMPP Connection Request mechanism as defined in
Annex K. These XMPP Connection Objects can also be used for other communications
that are yet to be defined by the Broadband Forum, but might be at some time in the
future (or maybe for a purely proprietary means of communicating between the CPE and
some entity connected to an XMPP Server).
III.2 XMPP Summary
This section provides a brief overview of the XMPP protocol for the purposes of assisting
the reader in the remaining sections of this Appendix. The reader should be familiar with
RFC 6120 [37], which is the authoritative source of this information.
XMPP is a communications protocol that permits bi-directional exchange of messages
between entities using globally addressable clients and servers. In order to exchange
messages between entities, the entities connect to a server as a client (called a “client-to-
server” connection or more commonly a “c2s” connection). The clients may connect to
the same or different servers. In the case where clients connect to multiple servers, the
servers to which the client(s) connect are themselves connected (called a “server-to-
server” connection or more commonly a “s2s” conection). In this architecture the CPE is
a client to an XMPP server, and the ACS can also be a client to an XMPP Server (for the
purpose of sending XMPP Connection Requests as defined in Annex K). Figure 25 in
Appendix III.6 depicts an example deployment scenario where the ACS and CPE connect
to different XMPP servers.
III.3 XMPP Identities
In order for entities to communicate using XMPP the entities are assigned globally
unique addresses as defined in Section 2.1/RFC 6120 [37] (also known as a Jabber ID).
In the context of this Appendix, the Jabber ID of interest is the one assigned to the CPE,
by the first-hop XMPP Server, and further described in the following sub-section.

III.3.1 CPE Considerations

The Jabber ID is comprised of three parts: local-part, domain-part, and resource-part.
These three parts are combined together in the following format: “local-part@domain-

November 2013 © The Broadband Forum. All rights reserved. Page 214 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

part/resource-part”. A CPE will attempt to use the following Parameters from within the
XMPP.Connection Object for the associated parts of the Jabber ID: the Username is the
local-part, the Domain is the domain-part, and the Resource is the resource-part. The
first-hop XMPP Server is ultimately responsible for determining the Jabber ID and
informing the XMPP Client (the CPE) of what that Jabber ID is, thus there is also a
JabberID Parameter within the XMPP.Connection Object that maintains the full Jabber
ID that is dictated by the first-hop XMPP Server.
Typically a CPE’s Jabber ID would use the CWMP unique triplet of OUI-ProductClass-
SerialNumber as the local-part as that is a common unique identifier used within CWMP.
An example of a Jabber ID for a CPE would be: “OUI-ProductCode-
[email protected]/XMPPConn1” where the:
 OUI-ProductCode-SerialNumber : represents the Username (local-part)
 tr069.example.com : represents the Domain (domain-part)
 XMPPConn1 : represents the Resource (resource-part)

III.4 Establishing an XMPP Connection

In order to exchange messages between XMPP clients, the client needs to establish an
XMPP Connection to the configured XMPP Server. The XMPP Client establishes this
connection by establishing two XML Streams as detailed in the following process (from
the perspective of the CPE):
 Open a TCP Connection to the XMPP Server
 Open an XML Stream to the XMPP Server
 Accept an XML Stream from the XMPP Server
 Negotiate a TLS encrypted XMPP channel (if required)
 Authenticate the XMPP channel using SASL credentials
 Bind the resource to determine the full Jabber ID of the XMPP Client
Once the CPE establishes the XML Streams, the CPE can then exchanges messages with
other XMPP Clients using XML Stanzas. Annex K defines how an ACS (acting as an
XMPP Client) can issue an XMPP Connection Request via an XML Stanza.

III.4.1 Determining the XMPP Server Address and Port

In order for an XMPP Client to connect to an XMPP Server, the client must know the IP
address and port of the server. The XMPP.Connection Object provides multiple
mechanisms to determine the XMPP Server to which the XMPP Client connects:
 DNS-SRV - Use the connection algorithm as specified in Section 3.2/RFC 6120
[37] where the value of the Domain parameter is used to look up the server
address and port to use. This is the default connection algorithm.
 ServerTable - Use the instances of the Server table (a table on the
XMPP.Connection instance) based on the value of a Server instance’s Priority and

November 2013 © The Broadband Forum. All rights reserved. Page 215 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Weight parameter values to determine the appropriate server address and port to
use.
These options are provisioned in the XMPP Connection using the ServerConnect-
Algorithm Parameter within the XMPP.Connection Object.

III.4.2 XML Streams

XML Streams are unidirectional, meaning that there needs to be a stream from the XMPP
Client to the XMPP Server and another stream from the XMPP Server to the XMPP
Client as the messages only flow in one direction on each stream. The concept of
directionality only applies to XML Stanzas that are sent after the XML Streams have
been established (meaning that it doesn’t apply to TLS negotiation or SASL
authentication). These two XML Streams can occupy one or two TCP connections, but
according to Section 4.5/RFC 6120 [37], the most common approach for “client-to-
server” connections is to use a single TCP connection for both XML Streams where the
security context negotiated for the first stream is applied to the second stream.

III.4.3 XMPP Connection Encryption

During the process of establishing an XMPP connection, if the XMPP Server is
configured such that TLS is “mandatory-to-negotiate”, then the XMPP connection needs
to be encrypted using the STARTTLS extension of the Transport Layer Security (TLS)
protocol as defined in Section 5/RFC 6120 [37].

III.4.4 XMPP Channel Authentication

Once the XMPP connection is encrypted, the XMPP Connection is authenticated using
the Simple Authentication and Security Layer (SASL) protocol as defined in Section
6/RFC 6120 [37]. The Username and Password Parameters of the XMPP.Connection
Object are used as the credentials for the SASL authentication procedure.

III.4.5 Reconnecting to the XMPP Server

There are some maintenance and unexpected scenarios where the XMPP Server, to which
an XMPP Client has connected, goes offline. In this situation the XMPP Client needs to
reconnect with the XMPP Server in order to maintain uninterrupted service. Section
3.3/RFC 6120 [37] defines a set of reconnection requirements for an XMPP Client. The
following recommendations are also to be followed by CPE that establish an XMPP
Connection.
If a CPE loses its connection to the XMPPP Server, it needs to reconnect using the set of
XMPP Servers configured in the ServerConnectAlgorithm Parameter associated with the
XMPP.Connection instance that needs to be reconnected.
In situations where there are long outages, many CPE that implement Section 3.3/RFC
6120 [37] will abort retry requests for a specific server after some number of attempts. In
order to provide more control, the recommendation here is to utilize the
ServerConnectAttempts, ServerRetryInitialInterval, ServerRetryIntervalMultiplier, and
ServerRetryMaxInterval Parameters associated with the XMPP.Connection instance that
needs to be reconnected.

November 2013 © The Broadband Forum. All rights reserved. Page 216 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

III.5 Maintaining an XMPP Connection

The XMPP Client connection to an XMPP Server is considered to be a long lived TCP
session. As such, the XMPP client needs to periodically send Keep-Alive messages to the
server in order to maintain the TCP session. The preferred mechanism is to utilize the
“whitespace keepalive” mechanism defined in Section 4.6.1/RFC 6120 [37] where an
XMPP Client sends a single space character between XML Stanzas.
The KeepAliveInterval Parameter within the XMPP.Connection Object allows an ACS to
configure the keepalive frequency in the following ways:
 Value = -1 : the whitespace keepalive mechanism is implementation specific and
determined by the CPE (default option)
 Value = 0 : the whitespace keepalive mechanism is disabled (not recommended)
 Value > 0 : the whitespace keepalive messages should be sent every
KeepAliveInterval seconds as configured by the ACS

III.6 Deployment Considerations

Firewalls are typically classified as one of three different types: Packet Filter Firewall,
Application Layer Firewall, and Stateful Firewall. A Packet Filter Firewall simply filters
each packet based on the information contained within the packet itself, meaning that it
does not pay attention to whether the packet is part of an existing stream of traffic. An
Application Layer Firewall operates on all 7 layers of the stack, instead of the first 3
layers like the Packet Filter Firewall, so it has the capability of not only filtering packets
but also filtering information based on content. A Stateful Firewall does everything that
an Application Layer Firewall does but also maintains records for every connection
passing through the firewall and can thus perform stateful packet inspection of that
information.
This means that if a Stateful Firewall is being utilized to separate the CPE from the ACS
and XMPP Servers then there could be load/scale issue for it to maintain all of the open
connections between the XMPP Clients on the CPE and the XMPP Server cluster. A
work around to this concern would be to place an Application Layer Firewall in front of
the Stateful Firewall and have the main CPE-bearing XMPP cluster resides between the
Application Layer Firewall and the Stateful Firewall. The XMPP Client that the ACS
utilizes could still reside behind the Stateful Firewall and utilize a small cluster of XMPP
Servers that also reside behind the Stateful Firewall, meaning that there would be a single
server-to-server connection between the 2 sets of XMPP Server clusters (see below for a
visual depiction of this configuration).

November 2013 © The Broadband Forum. All rights reserved. Page 217 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Figure 25 – XMPP Deployment Option – Stateful Firewall

November 2013 © The Broadband Forum. All rights reserved. Page 218 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Appendix IV. UPnP IGD and HTTP

Connection Requests

IV.1 Introduction
This section describes a mechanism allowing a CPE that is not directly addressable by its
ACS to make standard Connection Requests possible, by taking advantage of the UPnP
Internet Gateway Device framework. This mechanism is an alternative to the XMPP-
based solution defined in Annex K, but this mechanism is only applicable if the gateway,
behind which the CPE resides, supports UPnP IGD [39] and [40] with the necessary
services and allows the CPE to use them. Two different kinds of actions may be required
from the CPE: managing port mappings and/or creating a pinhole in an IPv6 firewall.

IV.2 NAT Port Mapping Theory of Operation

The UPnP Internet Gateway Device framework allows management of Port Mappings in
a NAT-enabled gateway, which can be used to allow Connection Requests to reach a
CPE from the WAN. This is only possible if the gateway implements the
WANIPConnection:2 service [42] or the WANPPPConnection:1 service [41], depending
on the WAN access protocol in use. The CPE also needs to embed a UPnP Control Point
supporting the UPnP WANIPConnection:2 and WANPPPConnection:1 services. The
general procedure has the CPE discovering the gateway’s WAN interface settings and IP
address, which allows it to open a port mapping from an external port towards the port
the CPE wants to use for receiving Connections Requests, and concludes with the CPE
setting its ConnectionRequestURL value based on information retrieved and configured
through UPnP IGD.
The UPnP IGD framework and methods are also used to manage changes of Connection
Request URL related parameters when an IP address (CPE, gateway, or ACS) is modified
or when the CPE or gateway is shutting down.
The discovery phase is independent from the WAN protocol and is described in Section
IV.2.1, but the other operations differ: the PPP case (WANPPPConnection:1 Service) is
described in Section IV.2.2 and the IP case (WANIPConnection:2 Service) in Section
IV.2.3.

IV.2.1 Discovery and External IP Address Retrieval

The CPE first discovers the UPnP IGD Gateway on the local network by sending an
SSDP M-SEARCH request.

November 2013 © The Broadband Forum. All rights reserved. Page 219 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Once the UPnP IGD Gateway detects that it is being searched for, it sends back a unicast
message to the CPE. The information contained in this response allows the CPE to
retrieve the description of the gateway and all necessary information concerning the
services that it hosts.
The CPE checks whether the gateway supports a WANPPPConnection:1 service or a
WANIPConnection:2 service. If the gateway supports neither the
WANPPPConnection:1 service nor the WANIPConnection:2 service, or the gateway
supports multiple WAN interfaces, the CPE needs to use an alternate solution.
When the UPnP IGD Gateway is found, the CPE uses the subscription mechanism
provided by UPnP in order to be notified of changes. Then, right after the subscription,
the CPE LAN Device gets the WAN IP address via a Gateway notification. By using the
UPnP notification/subscription mechanism, the CPE does not have to use the
GetExternalIPAddress method. The CPE MUST continue to monitor for advertisements
from the UPnP IGD Gateway so as not to miss reboots.

IV.2.2 Procedures for WANPPPConnection:1

Before creating a new port mapping entry, the CPE needs to check whether the port
mapping already exists. This is done by invoking the GetSpecificPortMappingEntry
UPnP action on the gateway. The input arguments for this UPnP action are as follows:
Input argument Recommended Contents
NewRemoteHost The ACS IP address
NewExternalPort The port on which Connection Request packets issued by the ACS will
be received by the gateway
NewProtocol The protocol used for the Connection Request

The result of the GetSpecificPortMappingEntry action provides the CPE with the
knowledge of whether or not the port mapping entry exists.
If the port mapping entry already exists, the NewInternalClient value, returned by the
Gateway, provides information regarding which device the packets are being forwarded
to. If the existing port mapping entry is used by another client (NewInternalClient value
is not the IP address of the CPE), then the CPE chooses a new external port and tries
again. If the existing port mapping entry is for this device (NewInternalClient value is
the IP address of the CPE), then the CPE uses the existing port mapping entry.
If the port mapping entry does not exist, the CPE attempts to create a new port mapping
entry by invoking the AddPortMapping UPnP action. The input arguments for this UPnP
action are as follows:
Input argument Recommended Contents
NewRemoteHost The ACS IP address (IP filter security is possible)
NewExternalPort The port on which Connection Request packets issued by the ACS will
be received by the gateway
NewProtocol The protocol used for the Connection Request
NewInternalPort The port that the CPE is listening to for Connection Requests sent by
the ACS

November 2013 © The Broadband Forum. All rights reserved. Page 220 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Input argument Recommended Contents

NewInternalClient The IP address of the CPE
NewLeaseDuration The lease duration of the port mapping entry. The CPE would typically
use a small value (e.g., less than 5 minutes) to avoid port maping
cleanup issues
PortMappingDescription Human-readable description associated to this port mapping entry
(optional)

If the action fails, an error response is returned to the CPE. When this happens, the
following actions can be taken (based on the error that was returned):
 "Action failed": the UPnP action failed and the CPE needs to use an alternate
solution
 "Conflict in mapping entry": the CPE needs to restart the procedure with a
different NewExternalPort value (e.g. former NewExternalPort +1)
If the port mapping entry has been successfully created or identified, the CPE sets the
ConnectionRequestURL value (http://host:port/path) of its Data Model where:
 The “host” value is the discovered WAN IP address of the Gateway
(ExternalIPAddress)
 The “port” value is the NewExternalPort either from the
GetSpecificPortMappingEntry UPnP action (if the port mapping entry already
existed and was associated to this device) or from the AddPortMapping UPnP
action (if a new port mapping entry was created)
 The “path” value is the path the CPE wants to use
If the ConnectionRequestURL parameter is configured for Active notifications (which is
typically default behaviour), the CPE issues an Inform RPC to the ACS with a “4
VALUE CHANGE” event code whenever the ConnectionRequestURL value is altered.
Once the port mapping entry has been established, the CPE is responsible for keeping the
port mapping entry from expiring. This can be done by periodically invoking the
AddPortMapping UPnP action, using the same parameter values as the existing port
mapping entry.

November 2013 © The Broadband Forum. All rights reserved. Page 221 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Figure 26 – Message flows when the CPE LAN device starts up normally

November 2013 © The Broadband Forum. All rights reserved. Page 222 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

IV.2.3 Procedures for WANIPConnection:2

The CPE attempts to create a port mapping entry by invoking the AddAnyPortMapping
UPnP action. The input arguments for this UPnP action are as follows:
Input argument Recommended Contents
NewRemoteHost The ACS IP address (IP filter security is possible)
NewExternalPort The port on which Connection Request packets issued by the ACS will
be received by the gateway
NewProtocol The protocol used for the Connection Request
NewInternalPort The port that the CPE is listening to for Connection Requests sent by
the ACS
NewInternalClient The IP address of the CPE
NewLeaseDuration The lease duration of the port mapping entry. The CPE would typically
use a small value (e.g., less than 5 minutes) to avoid port mapping
cleanup issues, and the gateway removes dynamic port mapping
entries across resets or reboots
PortMappingDescription Human-readable description associated to this port mapping entry
(optional)

If the action fails, an error response is returned to the CPE. When this happens, the CPE
needs to use an alternate solution.
If the gateway successfully creates the port mapping entry, a response containing a
NewReservedPort argument is sent back to the CPE. The value of NewReservedPort
might be different from the one proposed by the CPE, and this is why there is no need to
check the existing port mapping entries before attempting to create a new one, as is done
in the procedures defined in Section IV.2.2.
When the port mapping entry has been successfully created, the CPE sets the
ConnectionRequestURL value (http://host:port/path) of its Data Model where:
 The “host” value is the discovered WAN IP address of the Gateway
(ExternalIPAddress)
 The “port” value is the NewReservedPort from the AddAnyPortMapping UPnP
action
 The “path” value is the path the CPE wants to use
If the ConnectionRequestURL parameter is configured for Active notifications (which is
typically default behaviour), the CPE issues an Inform RPC to the ACS with a “4
VALUE CHANGE” event code whenever the ConnectionRequestURL value is altered.
Once the port mapping entry has been established, the CPE is responsible for keeping the
port mapping entry from expiring. This can be done by periodically invoking the
AddAnyPortMapping UPnP action, using the same parameter values as the existing port
mapping entry (according to the UPnP specification a call to AddAnyPortMapping with
the same Protocol, ExternalPort, RemoteHost, and InternalClient of an existing port
mapping entry will simply refresh the lease duration instead of creating a new port
mapping entry with a different reserved port).

November 2013 © The Broadband Forum. All rights reserved. Page 223 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Figure 27 – Message flows when the CPE LAN device starts up normally

IV.2.4 Handling Changes

When the CPE reboots or its IP address changes, it applies the above procedures again to
restore the appropriate mapping and communicate the ConnectionRequestURL change to
the ACS.
When the gateway reboots or its IP address changes, the new address is notified to the
CPE through its UPnP IGD subscription, at which point the CPE needs to apply the
above procedures again to restore the appropriate mapping and communicate the
ConnectionRequestURL change to the ACS.

IV.3 IPv6 Pinhole Theory of Operation

RFC 6092 [44] states that “the general operating principle is that transport layer traffic
is not forwarded into the interior network of a residential IPv6 gateway unless it has
been solicited explicitly by interior transport endpoints.” As such, Section
LAN.PFWDv6.1 of TR-124 Issue 3 [45] requires that Connection Requests sent by the
ACS to a CPE that resides behind an IPv6 firewall are dropped.
The UPnP Internet Gateway Device framework allows management of IPv6 Inbound
Pinholes in the IPv6 Firewall of the gateway, which allow Connection Requests to reach
the CPE from the WAN. This is only possible if the gateway and CPE implement the
UPnP IGD WANIPv6FirewallControl:1 service [43]. The general procedure has the CPE
discovering the gateway’s status of the embedded firewall, which allows it to create and

November 2013 © The Broadband Forum. All rights reserved. Page 224 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

maintain an Inbound Pinhole in the IPv6 Firewall rules of the gateway for the purpose of
relaying Connection Request messages to the CPE.
The UPnP IGD framework and methods are also used to manage changes of Connection
Request URL related parameters when an IP address (CPE, gateway, or ACS) is modified
or when the CPE or gateway is shutting down.

IV.3.1 Discovery
The CPE first discovers the UPnP IGD Gateway on the local network by sending an
SSDP M-SEARCH request.
Once the UPnP IGD Gateway detects that it is being searched for, it sends back a unicast
message to the CPE. The information contained in this response allows the CPE to
retrieve the description of the gateway and all necessary information concerning the
services that it hosts.
The CPE checks whether the gateway has a WANIPv6FirewallControl:1 service. If the
gateway doesn’t support the WANIPv6FirewallControl:1, the CPE needs to use an
alternative solution.

IV.3.2 Procedures
The CPE retrieves the IPv6 firewall status and the ability to add pinholes by invoking the
GetFirewallStatus UPnP action (there are no arguments for this UPnP action).
 If the firewall is disabled, the LAN device doesn't have to worry about the
firewall blocking Connection Requests from the ACS
 If the firewall is enabled and the CPE is not allowed to create Inbound Pinholes,
the CPE needs to use an alternative solution
The CPE opens a pinhole on the firewall of the gateway for the port on which the CPE is
listening on for Connection Requests by invoking the AddPinhole UPnP action. The
input arguments for this UPnP action are as follows:
Input argument Recommended Contents
RemoteHost The ACS IP address (IP filter security is possible)
RemotePort The port on which Connection Request packets issued by the ACS will
be received by the gateway
InternalClient The IP address of the CPE
InternalPort The port that the CPE is listening to for Connection Requests sent by
the ACS
LeaseTime The lease duration of the pinhole. The CPE would typically use a small
value (e.g., less than 5 minutes) to avoid pinhole cleanup issues
Protocol The protocol used for the Connection Request

The gateway might have sent back an error to the CPE as a result of calling the
AddPinhole UPnP action. In this case, the CPE needs to use an alternative solution.
When the Inbound Pinhole has been successfully create, the CPE sets the
ConnectionRequestURL value (http://host:port/path) of its Data Model where:

November 2013 © The Broadband Forum. All rights reserved. Page 225 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

 The “host” value is the IPv6 address of the CPE

 The “port” value is the port opened in the Firewall
 The “path” value is the path the CPE wants to use
If the ConnectionRequestURL parameter is configured for Active notifications (which is
typically default behaviour), the CPE issues an Inform RPC to the ACS with a “4
VALUE CHANGE” event code whenever the ConnectionRequestURL value is altered.
Once the Inbound Pinhole has been established, the CPE is responsible for keeping the
pinhole from expiring. This can be done by periodically invoking the UpdatePinhole
UPnP action. The input arguments for this UPnP action are as follows:
Input argument Recommended Contents
UniqueID The unique ID of the Inbound Pinhole returned by original AddPinhole
UPnP action
NewLeaseTime The lease duration of the Inbound Pinhole. The CPE would typically
use a small value (ie, less than 5 minutes) to avoid pinhole cleanup
issues

November 2013 © The Broadband Forum. All rights reserved. Page 226 of 228
 CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

Figure 28 – Message flows when the CPE LAN device starts up normally

IV.3.3 Handling Changes

When the CPE reboots or its IP address changes, it applies the above procedures again to
restore the appropriate mapping and communicate the ConnectionRequestURL change to
the ACS.
When the gateway reboots or its IP address changes, the new address is notified to the
CPE through its UPnP IGD subscription, at which point the CPE needs to apply the
above procedures again to restore the appropriate pinhole and communicate the
ConnectionRequestURL change to the ACS.

November 2013 © The Broadband Forum. All rights reserved. Page 227 of 228
CPE WAN Management Protocol TR-069 Issue 1 Amendment 5

End of Broadband Forum Technical Report TR-069

November 2013 © The Broadband Forum. All rights reserved. Page 228 of 228