Manual

Download as pdf or txt
Download as pdf or txt
You are on page 1of 190

Preface

Notice
The company reserves the right to revise this publication or to change its contents without notice. Information
contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or
any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear
in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse)
of this publication.
This publication and any accompanying software may not, in whole or in part, be reproduced, translated, trans-
mitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators
of this publication, except for copies kept by the user for backup purposes.
Brand and product names mentioned in this publication may or may not be copyrights and/or registered trade-
marks of their respective companies. They are mentioned for identification purposes only and are not intended
as an endorsement of that product or its manufacturer.
©August 2007

Trademarks
This product incorporates copyright protection technology that is protected by method claims of certain U.S. pat-
ents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of
this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home
or other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineer-
ing or disassembly is prohibited.
Intel, Celeron, and Intel Core are trademarks/registered trademarks of Intel Corporation.

I
Preface

FCC Statement
(Federal Communications Commission)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-
stalled and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Re orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the service representative or an experienced radio/TV technician for help.


Warning
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not ex-
pressly approved by the manufacturer for compliance with the above standards could void your authority to operate the
equipment.

II
Preface

IMPORTANT SAFETY INSTRUCTIONS


Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury
to persons when using any electrical equipment:

1. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet
basement or near a swimming pool.
2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There
may be a remote risk of electrical shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may
explode. Check with local codes for possible special disposal instructions.
5. This product is intended to be supplied by a Listed Power Unit (Full Range AC/DC Adapter - AC Input 100 -
240V, 50 - 60Hz / DC Output 19V, 3.42A or 18.5V, 3.5A (65W) minimum).

CAUTION
Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment.

TO REDUCE THE RISK OF FIRE, USE ONLY NO. 26 AWG OR LARGER,


TELECOMMUNICATION LINE CORD

This Computer’s Optical Device is a Laser Class 1 Product

III
Preface

Instructions for Care and Operation


The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:

1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.

Do not expose the computer Do not place it on an unstable Do not place anything heavy
to any shock or vibration. surface. on the computer.

2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating ele-
ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly dam-
aged.

Do not expose it to excessive Do not leave it in a place Don’t use or store the com- Do not place the computer on
heat or direct sunlight. where foreign matter or mois- puter in a humid environment. any surface that will block the
ture may affect the system. Vents/Fan Intakes.

IV
Preface

3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other
strong magnetic fields. These can hinder proper performance and damage your data.

4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget
to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.

Do not turn off the power Do not turn off any peripheral Do not disassemble the com- Perform routine maintenance
until you properly shut down devices when the computer is puter by yourself. on your computer.
all programs. on.

5. Take care when using peripheral devices.

Use only approved brands of Unplug the power cord before


peripherals. attaching peripheral devices.

V
Preface

Power Safety
The computer has specific power requirements:

 • Only use a power adapter approved for use with this computer.
Power Safety • Your AC/DC adapter may be designed for international travel but it still requires a steady,
Warning uninterrupted power supply. If you are unsure of your local power specifications, consult
Before you undertake your service representative or local power company.
any upgrade proce- • The power adapter may have either a 2-prong or a 3-prong grounded plug. The third prong
dures, make sure that is an important safety feature; do not defeat its purpose. If you do not have access to a
you have turned off the compatible outlet, have a qualified electrician install one.
power, and discon- • When you want to unplug the power cord, be sure to disconnect it by the plug head, not by
nected all peripherals its wire.
and cables (including
• Make sure the socket and any extension cord(s) you use can support the total current load
telephone lines). It is
advisable to also re- of all the connected devices.
move your battery in • Before cleaning the computer, make sure it is disconnected from any external power sup-
order to prevent acci- plies (i.e. AC/DC adapter or car adapter).
dentally turning the
machine on.
Do not plug in the power Do not use the power cord if Do not place heavy objects
cord if you are wet. it is broken. on the power cord.

VI
Preface

Battery Precautions
• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.
• Do not remove any batteries from the computer while it is powered on.
• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even
if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly
result in fire.
• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.
• Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service representative or qual-
ified service personnel.
• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries
may explode or leak if exposed to fire, or improperly handled or discarded.
• Keep the battery away from metal appliances.
• Affix tape to the battery contacts before disposing of the battery.
• Do not touch the battery contacts with your hands or metal objects.


Battery Disposal & Caution
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life,
under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with
your local solid waste officials for details in your area for recycling options or proper disposal.

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the
manufacturer. Discard used battery according to the manufacturer’s instructions.

VII
Preface

Cleaning
Do not apply cleaner directly to the computer; use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.

Servicing
Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the
computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the
power supply. Then refer servicing to qualified service personnel under any of the following conditions:

• When the power cord or AC/DC adapter is damaged or frayed.


• If the computer has been exposed to rain or other liquids.
• If the computer does not work normally when you follow the operating instructions.
• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).
• If there is an unusual odor, heat or smoke coming from your computer.


Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s) and
screw(s) before turning the computer on.

VIII
Preface

Travel Considerations
Packing
As you get ready for your trip, run through this list to make sure the system is ready to go:
1. Check that the battery pack and any spares are fully charged.
2. Power off the computer and peripherals.
3. Close the display panel and make sure it’s latched.
4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.
5. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter. However,
check with your travel agent to see if you need any socket adapters.
6. Put the notebook in its carrying bag and secure it with the bag’s straps.
7. If you’re taking any peripherals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters
and/or cables.
8. Anticipate customs - Some jurisdictions may have import restrictions or require proof of ownership for both hard-
ware and software. Make sure your “papers” are handy.


Power Off Before Traveling
Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a
notebook which is powered on in a travel bag may cause the Vents/Fan Intakes to be blocked. To prevent your computer
from overheating make sure nothing blocks the Vent/Fan Intakes while the computer is in use.

IX
Preface

On the Road
In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting,
keep these points in mind:

Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very
common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knock-
ing the computer against hard objects.

Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the com-
puter, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and
disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note:
Some airports also scan luggage with these devices.

Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight.
These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make
sure it’s secure. Contents may shift and/or fall out when the compartment is opened.

Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies)
charged.

Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer.
Wait a few minutes before turning it on so that any moisture can evaporate.

X
Preface

Developing Good Work Habits


Developing good work habits is important if you need to work in front of the computer for long periods of time.
Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or
other joints. The following are some tips to reduce the strain:

• Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the
level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
• Your knees should be slightly higher than your hips. Place your feet flat on the floor or on
a footrest if necessary.
• Use a chair with a back and adjust it to support your lower back comfortably.
• Sit straight so that your knees, hips and elbows form approximately 90-degree angles
when you are working.
• Take periodic breaks if you are using the computer for long periods of time.

Remember to:
• Alter your posture frequently.
• Stretch and exercise your body several times a day.
• Take periodic breaks when you work at the computer for long periods of time. Frequent
and short breaks are better than fewer and longer breaks.

XI
Preface

Lighting
Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and
shoulders.

• Position the display to avoid glare or reflections from overhead lighting or outside sources of light.
• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.
• Position the display directly in front of you at a comfortable viewing distance.
• Adjust the display-viewing angle to find the best position.

XII
Preface

Contents
Notice .................................................................................I System Map: Front & Rear Views ...............................1-12
FCC Statement .............................................................II System Map: Left View ...............................................1-13
Instructions for Care and Operation .......................... IV System Map: Right View .............................................1-14
Power Safety .............................................................. VI System Map: Bottom View ..........................................1-15
Battery Precautions ...................................................VII Windows Vista Start Menu & Control Panel ...............1-16
Cleaning .................................................................. VIII Video Features .............................................................1-17
Servicing ................................................................. VIII Power Options ..............................................................1-18
Travel Considerations ................................................ IX
Features & Components
Quick Start Guide Overview ........................................................................2-1
Overview ........................................................................1-1 Hard Disk Drive .............................................................2-2
Model Differences .......................................................1-2 Optical (CD/DVD) Device ............................................2-3
Advanced Users ...........................................................1-3 Loading Discs ..............................................................2-3
Beginners and Not-So-Advanced Users ......................1-3 Handling CDs or DVDs ...............................................2-4
Warning Boxes ............................................................1-3 DVD Regional Codes ..................................................2-5
Not Included ................................................................1-4 7-in-1 Card Reader .........................................................2-6
System Software ..........................................................1-5 ExpressCard Slot ............................................................2-7
System Startup ...............................................................1-6 Inserting and Removing ExpressCards ........................2-7
System Map: Model A - LCD Panel Open ....................1-7 Application Hot Key ......................................................2-8
System Map: Model B - LCD Panel Open ....................1-8 TouchPad and Buttons/Mouse .......................................2-9
LED Indicators ...............................................................1-9 Audio Features .............................................................2-10
Hot Key Buttons & Keyboard .....................................1-10 Adding a Printer ...........................................................2-11
Function Keys ..............................................................1-11 USB Printer ..............................................................2-11

XIII
Preface

Parallel Printer ..........................................................2-11 Drivers & Utilities


What to Install ................................................................4-1
Power Management Module Driver Installation ..........................................4-1
Overview ........................................................................3-1 Driver Installation ..........................................................4-2
The Power Sources ........................................................3-2 Updating/Reinstalling Individual Drivers ...................4-3
AC/DC Adapter ...........................................................3-2 Manual Driver Installation .........................................4-4
Battery .........................................................................3-2 User Account Control (Win Vista) ..............................4-5
Turning on the Computer ...............................................3-3 Windows Security Message .........................................4-5
Power Plans ...................................................................3-4 New Hardware Found ..................................................4-5
System Power Options ...................................................3-6 Driver Installation Procedure .......................................4-5
Hibernate vs. Shut Down .............................................3-6 Video ..........................................................................4-5
Sleep vs. Hibernate ......................................................3-6 Audio ..........................................................................4-5
Sleep ...........................................................................3-7 Modem ........................................................................4-6
Hibernate ....................................................................3-7 LAN ............................................................................4-6
Configuring the Power Buttons .....................................3-8 TouchPad ....................................................................4-6
Battery Information .......................................................3-9 CardReader .................................................................4-6
Battery Power .............................................................3-9 Hot Key ......................................................................4-6
Conserving Battery Power ...........................................3-10 Wireless LAN .............................................................4-7
Battery Life ..................................................................3-11 Bluetooth ....................................................................4-7
New Battery ..............................................................3-11 PC Camera ..................................................................4-7
Recharging the Battery with the AC/DC Adapter .....3-11
Proper handling of the Battery Pack .........................3-12 BIOS Utilities
Battery FAQ ..............................................................3-13
Overview ........................................................................5-1
Startup Screen ................................................................5-2
Setting a Boot Password ..............................................5-4

XIV
Preface

Setup Screens ...............................................................5-5 802.11 b/g USB WLAN Module ...................................7-2


Main Menu .....................................................................5-6 802.11 b/g WLAN Driver Installation ........................7-2
System Time & Date (Main Menu) ...............................5-6 Connecting to a Wireless Network ..............................7-3
IDE Channel 0/2 Master (Main Menu) ..........................5-7 Windows Mobility Center ...........................................7-6
System/Extended Memory: (Main Menu) .....................5-7 Bluetooth Module ..........................................................7-7
Advanced Menu .............................................................5-8 Bluetooth Driver Installation ......................................7-7
Installed O/S: (Advanced Menu) ...................................5-8 PC Camera Module ......................................................7-11
Legacy USB Support: (Advanced Menu) ......................5-9 PC Camera Driver Installation .................................7-11
Reset Configuration Data: (Advanced Menu) ...............5-9 PC Camera Audio Setup ...........................................7-12
Enable Multimedia Timer: (Advanced Menu) ..............5-9 BisonCap ...................................................................7-14
Frame Buffer Size: (Advanced Menu) ..........................5-9 Eliminating Screen Flicker .......................................7-15
Boot Menu ...................................................................5-10
Exit Menu ....................................................................5-11 Troubleshooting
Overview ........................................................................8-1
Upgrading The Computer Basic Hints and Tips ......................................................8-2
Overview ........................................................................6-1 Backup and General Maintenance .................................8-3
When Not to Upgrade ..................................................6-2 Viruses ...........................................................................8-4
Removing the Battery ....................................................6-3 Upgrading and Adding New Hardware/Software ..........8-5
Upgrading the Hard Disk Drive .....................................6-5 Problems and Possible Solutions ...................................8-7
Upgrading the Optical (CD/DVD) Device ....................6-9 Non DDC CRT Monitors (for Win Vista Only) ..........8-12
Upgrading the System Memory (RAM) ......................6-11
Upgrading the Processor ..............................................6-14 Interface (Ports & Jacks)
Overview .......................................................................A-1
Modules & Options Notebook Ports and Jacks .............................................A-2
Overview ........................................................................7-1 Card Reader Port ...........................................................A-2

XV
Preface

DC-In Jack .................................................................... A-2 Security ......................................................................... C-2


External Monitor (VGA) Port ....................................... A-2 BIOS ............................................................................. C-2
Headphone-Out Jack ..................................................... A-2 LCD .............................................................................. C-3
Recording Line-In Jack ................................................. A-2 Video Adapter ............................................................... C-3
Microphone-In Jack ...................................................... A-2 Storage .......................................................................... C-3
RJ-11 Modem Jack ....................................................... A-3 Audio ............................................................................ C-3
RJ-45 LAN Jack ........................................................... A-3 Keyboard & Pointing Device ........................................ C-3
Security Lock Slot ........................................................ A-3 Interface ........................................................................ C-4
S/PDIF-Out Jack ........................................................... A-3 Card Reader .................................................................. C-4
USB 2.0/1.1 Ports ......................................................... A-3 ExpressCard Slot ........................................................... C-4
Communication ............................................................. C-4
Video Driver Controls Power Management ...................................................... C-4
VIA Video Driver Installation ...................................... B-1 Power ............................................................................ C-4
Video ......................................................................... B-1 Environmental Spec ...................................................... C-5
Advanced Video Controls ............................................. B-2 Physical Dimensions & Weight .................................... C-5
Video Driver Controls ............................................... B-2 Optional ........................................................................ C-5
Video Memory ........................................................... B-2
VIA S3Tray Plus Utility ............................................. B-3 Windows XP Information
Attaching Other Displays ............................................. B-4 Video Driver Controls ...............................................D-8
Display Modes .............................................................. B-6 Video Memory ...........................................................D-8
VIA S3Tray Plus Utility .............................................D-9
Specifications Advanced Configuration and Power Interface .........D-15
Processor ....................................................................... C-2 AC/DC Adapter ........................................................D-16
Core Logic .................................................................... C-2 Battery ...................................................................... D-16
Memory ......................................................................... C-2 Hibernate Mode vs. Shutdown .................................D-20

XVI
Preface

Stand by Mode vs. Hibernate Mode ......................... D-20


Recharging the Battery with the AC/DC Adapter .... D-24
Battery FAQ ............................................................. D-26
Updating/Reinstalling Individual Drivers ................ D-29
Authorized Driver Message ...................................... D-30
Version Conflict Message ........................................ D-30
BisonCap .................................................................. D-43

XVII
Preface

XVIII
Quick Start Guide
1
Chapter 1: Quick Start Guide
Overview
This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the
computer and to getting your system started. The remainder of the manual covers the following:

• Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk,
optical device, 7-in-1 card reader, ExpressCard), Application Hot Key, TouchPad & Mouse,
Audio and Printer.
• Chapter 3 The computer’s power saving options.
• Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the
computer’s subsystems.
• Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).
• Chapter 6 Instructions for upgrading your computer.
• Chapter 7 A quick guide to the computer’s Wireless LAN, Bluetooth, and PC Camera modules (some of
which may be optional depending on your purchase configuration).
• Chapter 8 A troubleshooting guide.
• Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external
devices.
• Appendix B Information on the VIA Video driver controls.
• Appendix C The computer’s specification.
• Appendix D Information on the Windows XP OS.

Overview 1 - 1
Quick Start Guide
1
Model Differences
This notebook series includes two different model types (each model includes two design styles). The models
differ slightly in design style including the LCD type, and the location of the card reader (the easiest way to dif-
ferentiate between the model types is the location of the card reader).

Feature Model A Model B

15.0" Flat Panel TFT 14.1" Flat Panel TFT


LCD Type
(see “LCD” on page C - 3 for details) (see “LCD” on page C - 3 for details)

Card Reader
Left Side Front
Location

Memory Sockets Two 200 Pin SODIMM Sockets (DD2 533/667) One 200 Pin SODIMM Sockets (DD2 533/667)

Design Styles

Table 1 - 1 - Model Differences

1 - 2 Overview
Quick Start Guide
1
Advanced Users
If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful
to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on
page 6 - 1 in the User’s Manual. You may also find the notes marked with a  of interest to you.

Beginners and Not-So-Advanced Users


If you are new to computers (or do not have an advanced knowledge of them) then 
the information contained in this Quick Start Guide should be enough to get you up Notes
and running. Eventually you should try to look through all the documentation (more
Check the light colored
detailed descriptions of the functions, setup and system controls are covered in the boxes with the mark
remainder of the User’s Manual), but do not worry if you do not understand every- above to find detailed
thing the first time. Keep this manual nearby and refer to it to learn as you go. You information about the
may find it useful to refer to the notes marked with a  as indicated in the margin. computer’s features.
For a more detailed description of any of the interface ports and jacks see “Interface
(Ports & Jacks)” on page A - 1.

Warning Boxes
No matter what your level please pay careful attention to the warning and safety information indicated by the
 symbol. Also please note the safety and handling instructions as indicated in the Preface.

Overview 1 - 3
Quick Start Guide
1
Not Included
Operating Systems (e.g. Windows Vista/Windows XP) and applications (e.g. word processing, spreadsheet and
database programs) have their own manuals, so please consult the appropriate manuals.


Drivers
If you are installing new system software, or are re-configuring your computer for a different system, you will need to install
the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the com-
puter and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order
listed in Table 4 - 1, on page 4 - 3. You will be unable to use most advanced controls until the necessary drivers and util-
ities are properly installed. If your system hasn’t been properly configured (your service representative may have already
done that for you), refer to “What to Install” on page 4 - 1 for installation instructions.

Ports and Jacks


See “Notebook Ports and Jacks” on page A - 2 for a description of the interface (ports & jacks) which allow your com-
puter to communicate with external devices, connect to the internet etc.

1 - 4 Overview
Quick Start Guide
1
System Software
Your computer may already come with system software pre-installed. Where this is not the case, or where you
are re-configuring your computer for a different system, you will find the following operating systems are sup-
ported.

Operating System & Version Supported Note

*Windows XP (Home or Professional) Yes

32-bit Yes
Windows Vista Home Basic
64-bit No
In order to run Windows Vista without
32-bit No limitations or decreased performance, your
Windows Vista Home Premium
64-bit No computer requires a minimum 1GB of
system memory (RAM).
Windows Vista 32-bit No
Business/Enterprise/Ultimate 64-bit No

Table 1 - 2 - Operating Systems Supported

*Note: For information on the Windows XP OS (specifically power, video and driver information) see “Win-
dows XP Information” on page D - 1.

Overview 1 - 5
Quick Start Guide
1
System Startup
1. Remove all packing materials.
2. Place the computer on a stable surface.
3. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports.
4. Attach the AC/DC adapter to the DC-In jack on the right of the computer, then plug the AC power cord into an
outlet, and connect the AC power cord to the AC/DC adapter.
5. Raise the lid/LCD to a comfortable viewing angle, and press the power button to turn the computer “on”.
6. Adjust the LCD panel to a comfortable viewing angle.
7. The LED Power & Communication indicators show the power and battery status of the computer.


Shutdown
Note that you should always shut your computer down by choos-
ing the Shut Down command from the Lock Button Menu in
Windows Vista. This will help prevent hard disk or system prob-
lems.

Figure 1 - 1 - Computer with AC/DC Adapter Plugged-In

1 - 6 System Startup
Quick Start Guide
1
System Map: Model A - LCD Panel Open
1
 1. Optional Built-In PC Camera
2. LCD
Wireless Device 3. LED Status Indicators
Operation Aboard 4. Hot Key Buttons
Aircraft 5. Power Button
2 6. Keyboard
The use of any portable elec-
tronic transmission devices 7. Built-In Microphone
aboard aircraft is usually pro- 8. TouchPad and Buttons
hibited. Make sure the mod- 9. LED Power & Communication
ule(s) are OFF if you are using
Indicators
the computer aboard aircraft.
3 4 5
Use the key combinations to 4
toggle power to the WLAN/
Bluetooth modules, and check 5
the status indicator icon to see
if the modules are powered on 6 Note: Only One Design Style is Pictured
or not (see “LED Indicators”
on page 1 - 9/“Function 3
Keys” on page 1 - 11).
7

8
9
Figure 1 - 2 - Model A - LCD Panel Open

System Map: Model A - LCD Panel Open 1 - 7


Quick Start Guide
1
System Map: Model B - LCD Panel Open
1
1. Optional Built-In PC Camera
2. LCD

3. Speaker Wireless Device
4. LED Status Indicators Operation Aboard
5. Hot Key Buttons Aircraft
6. Power Button 2
The use of any portable elec-
7. Keyboard tronic transmission devices
8. TouchPad and Buttons aboard aircraft is usually pro-
9. LED Power & Communication hibited. Make sure the mod-
Indicators ule(s) are OFF if you are using
the computer aboard aircraft.
10. Built-In Microphone 3
4 5 6
Use the key combinations to
toggle power to the WLAN/
Bluetooth modules, and check
7 the status indicator icon to see
5 6 if the modules are powered on
or not (see “LED Indicators”
Note: Only One Design Style is Pictured
on page 1 - 9/“Function
Keys” on page 1 - 11).

4
8
9 10

Figure 1 - 3 - Model B - LCD Panel Open

1 - 8 System Map: Model B - LCD Panel Open


Quick Start Guide
1
LED Indicators Table 1 - 4 - LED Power & Communication Indicators

The two sets of LED indicators (LED Status Indica- Icon Color Description
tors and LED Power & Communication Indicators)
Green The Computer is On
on the computer display helpful information about the
current status of the computer. Blinking
The Computer is in Sleep Mode
Green
Table 1 - 3 - LED Status Indicators The AC/DC Adapter is Plugged
Orange In & the Computer is Powered
Icon Color Description Off

Number Lock Activated (to activate The AC/DC Adapter is Plugged


Green Orange
press Fn & NumLk) In & the Battery is Charging
Blinking The Battery has Reached
Green Caps Lock Activated Orange Critically Low Power Status
Scroll Lock Activated (to activate Green The Battery is Fully Charged
Green
press Fn & ScrLk)
Green Hard Disk Activity

The WLAN Module is Powered


Green
On
The Bluetooth Module is
Orange
Powered On

LED Indicators 1 - 9
Quick Start Guide
1
Hot Key Buttons & Keyboard The keyboard has an embedded numerical keypad for
easy numeric data input, and features function keys to
These buttons give instant access to the functions indi- allow you to change operational features instantly (see
cated in the table below. Figure 1 - 4).
Table 1 - 5 - Hot Key Buttons
Function Keys
NumLk &
Hot Key Function ScrLk Keys
Numeric
Activate the user specified application Keypad
e.g.Microsoft Word or Excel

Activate the Default E-Mail Program


Fn Key
Activate the Default Internet Browser Figure 1 - 4 - Keyboard

See “Application Hot Key” on page 2 - 8 for configu-


ration instructions. 
Other Keyboards
Note: The hot key buttons may appear slightly differ-
ent from those illustrated in Table 1 - 5, depending on If your keyboard is damaged or you just want to make a
change, you can use any standard USB keyboard. The
your model/design.
system will detect and enable it automatically. However
special functions/hot keys unique to the system’s regular
keyboard may not work.

1 - 10 Hot Key Buttons & Keyboard


Quick Start Guide
1
Function Keys
To use the function keys, press and hold the Fn key, then press the appropriate function key (F1 - F12 etc.).

Key Function Key Function

Fn Function Key Fn + F7 Display Toggle

Fn + ~ Play/Pause (in Audio/Video Programs) Fn + F8 Decrease LCD Brightness

Fn + F1 TouchPad Toggle Fn + F9 Increase LCD Brightness

Turn LCD Backlight Off


Fn + F2 Fn + F10 PC Camera Power Toggle
(Press a key to or use TouchPad to turn on)
Fn + F3 Mute Toggle Fn + F11 Wireless Power Toggle

Fn + F4 Sleep Toggle Fn + F12 Bluetooth Power Toggle

Fn + F5 Decrease Audio Volume Fn + NumLk Number Lock Toggle

Fn + F6 Increase Audio Volume Fn + ScrLk Scroll Lock Toggle

Table 1 - 6 - Function Keys


Special Characters

Some software applications allow the number-keys to be used with Alt to produce special characters. These special characters can only be produced by using
the numeric keypad. Regular number keys (in the upper row of the keyboard) will not work. Make sure that NumLk is on.

Function Keys 1 - 11
Quick Start Guide
1
System Map: Front & Rear Views
1. LED Power & Model A - Front
Communication 2
Indicators 1
2. LCD Latch
(Model A Only) Model B - Front
3. 7-in-1 Card Reader
(Model B Only) 1 3
4. External Monitor Port
5. Security Lock Slot Rear
6. Battery 6
4 5

Figure 1 - 5 - Front & Rear Views


7-in-1 Card Reader
The card reader allows you to use the most popular digital storage card formats:
MMC (MultiMedia Card) / SD (Secure Digital) / MS (Memory Stick) / MS Pro (Memory Stick Pro)
MS Duo (requires PC adapter) / Mini SD (requires PC adapter) / RS MMC (requires PC adapter)

1 - 12 System Map: Front & Rear Views


Quick Start Guide
1
System Map: Left View
1. RJ-45 LAN Jack
Model A - Left 2. Vent/Fan Intake
6 3. 2 * USB 2.0 Ports
1 2 3 4 5 7 4. S/PDIF-Out Jack
5. Recording Line-In Jack (see
Model B - Left page A - 2)
6 6. ExpressCard Slot
3 4 5 7. 7-in-1 Card Reader
1 2 (Model A Only)
Figure 1 - 6 - Left View


ExpressCard Slot
The ExpressCard Slot accepts either ExpressCard/34 or ExpressCard/54 formats.

7-in-1 Card Reader


The card reader allows you to use the most popular digital storage card formats:
MMC (MultiMedia Card) / SD (Secure Digital) / MS (Memory Stick) / MS Pro (Memory Stick Pro)
MS Duo (requires PC adapter) / Mini SD (requires PC adapter) / RS MMC (requires PC adapter)

System Map: Left View 1 - 13


Quick Start Guide
1
System Map: Right View
Figure 1 - 7 - Right View
1. Headphone-Out Jack
2. Microphone-In Jack
3. USB 2.0 Port 1 2 3 4 5 6
4. RJ-11 Modem Jack
5. Optical Device Drive Bay
(for CD/DVD Device - see
page 2 - 3) 
6. DC-In Jack
Changing DVD Regional Codes

 Go to the Control Panel and double-click Device


Manager (Hardware and Sound), then click the +
CD Emergency Eject next to DVD/CD-ROM drives. Double-click on the
DVD-ROM device to bring up the Properties dia-
If you need to manually eject a CD/DVD (e.g. due to an unex- logue box, and select the DVD Region (tab) to bring
pected power interruption) you may push the end of a straight- up the control panel to allow you to adjust the region-
ened paper clip into the emergency eject hole. Do not use a al code (see “DVD Regional Codes” on page 2 -
sharpened pencil or similar object that may break and become 5).
lodged in the hole.
DVD region detection is device dependent, not OS-
Media Warning dependent. You can select your module’s region
code 5 times. The fifth selection is permanent. This
Don’t try to remove a floppy disk/CD/DVD while the system is cannot be altered even if you change your operating
accessing it. This may cause the system to “crash”. system or you use the module in another computer.

1 - 14 System Map: Right View


Quick Start Guide
1
System Map: Bottom View
2 1. Vent/Fan Intake
 2. Battery
Model A 3. Component Bay Cover
CPU
1 4. Hard Disk Cover
The CPU is not a user ser- 5. Speakers
viceable part. Opening this 3
compartment, or accessing
the CPU at all, may violate 2
your warranty. Model B
4 1
1
Overheating
To prevent your computer
5 5 1 3
from overheating make
sure nothing blocks the
Vent/Fan Intake while the
computer is in use. 4 1


Battery Information
Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery
at least once every 30 days or after about 20 partial discharges (see “Battery Information” on page 3 - 9).

System Map: Bottom View 1 - 15


Quick Start Guide
1
Windows Vista Start Menu & Control Panel
Most of the control panels, utilities and programs within Windows Vista (and most other Windows versions) are
accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk
drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu
icon , and then select Properties if you want to customize the appearance of the Start menu.

Click here to toggle Classic View

Figure 1 - 8 - Start Menu & Control Panel

In many instances throughout this manual you will see an instruction to open the Control Panel. The Control
Panel is accessed from the Start menu, and it allows you to configure the settings for most of the key features
in Windows (e.g. power, video, network, audio etc.). Windows Vista provides basic controls for many of the fea-
tures, however many new controls are added (or existing ones are enhanced) when you install the drivers listed
in Table 4 - 1, on page 4 - 3. To see all controls it may be necessary to toggle to Classic View on.

1 - 16 Windows Vista Start Menu & Control Panel


Quick Start Guide
1
Video Features
You can switch display devices, and configure display options, from the Display Settings control panel (in Per-
sonalization) in Windows Vista. For further information see “Video Driver Controls” on page B - 1.
To access Display Properties in Windows Vista:
1. Click Start, and click Control Panel (or point to Settings and click Control Panel).
2. Click Adjust screen resolution under the Appearance and Personalization menu (or double-click
Personalization > Display Settings).
3. Move the slider to the preferred setting in Resolution: 1 (Figure 1 - 9).
4. Click the arrow, and scroll to the preferred setting In Colors: 2 (Figure 1 - 9).
5. Click Advanced Settings (button) 3 (Figure 1 - 9) to bring up the Advanced Settings tabs.
OR
6. Right-click the desktop and click Personalize, and then click Display Settings and adjust as above.

Figure 1 - 9
Display Settings

2
1
3

Video Features 1 - 17
Quick Start Guide
1
Power Options
The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 16) allows you
to configure power management features for your computer. You can conserve power by means of power plans
and configure the options for the power button, sleep button, computer lid (when closed), display and sleep
mode from the left menu. Note that the Power saver plan may have an affect on computer performance.
Click to select one of the existing plans, or click Create a power plan in the left menu and select the options to
create a new plan. Click Change Plan Settings and click Change advanced power settings to access further con-
figuration options.
Pay attention to the instructions on battery care in “Battery Information” on page 3 - 9.

Note: Sleep is the default power saving state in Windows Vista


Figure 1 - 10 - Power Options

1 - 18 Power Options
Features & Components

Chapter 2: Features & Components 2


Overview
Read this chapter to learn more about the following main features and components
of the computer:

• Hard Disk Drive


• Optical (CD/DVD) Device
• 7-in-1 Card Reader
• ExpressCard Slot
• Application Hot Key
• TouchPad and Buttons/Mouse
• Audio Features
• Adding a Printer

Overview 2 - 1
Features & Components

2 Hard Disk Drive


 The hard disk drive is used to store your data in the computer. The hard disk can be
Power Safety taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height
Before attempting to ac- of 9.5 mm.
cess any of the internal
components of your The hard disk is accessible from the bottom of your computer as seen below. For fur-
computer please ensure ther details see “Upgrading the Hard Disk Drive” on page 6 - 5 .

that the machine is not


connected to the AC
power, and that the ma-
chine is turned off. Also
ensure that all peripher-
al cables, including Model A Model B
phone lines, are discon-
nected from the comput-
er.

Figure 2 - 1 Hard Disk


Hard Disk Location
Hard Disk

2 - 2 Hard Disk Drive


Features & Components

Optical (CD/DVD) Device 2


There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual de-

vice will depend on the module you purchased (see “Storage” on page C - 3). The Sound Volume
optical device is usually labeled “Drive D:” and may be used as a boot device if Adjustment
properly set in the BIOS (see “Boot Menu” on page 5 - 10). How high the sound vol-
ume can be set depends
on the setting of the vol-
Loading Discs ume control within Win-
To insert a CD/DVD, press the open button 1 and carefully place a CD/DVD onto dows. Click the Volume
the disc tray with label-side facing up (use just enough force for the disc to click onto icon on the taskbar to
the tray’s spindle). Gently push the CD/DVD tray in until its lock “clicks” and you check the setting (see
“Audio Features” on
are ready to start. The busy indicator 2 will light up while data is being accessed, page 2 - 10).
or while an audio/video CD, or DVD, is playing. If power is unexpectedly interrupt-
ed, insert an object such as a straightened paper clip into the emergency eject hole
3 to open the tray.
Figure 2 - 2
Optical Device

2 3

Optical (CD/DVD) Device 2 - 3


Features & Components

Handling CDs or DVDs


2  Proper handling of your CDs/DVDs will prevent them from being damaged. Please
CD Emergency Eject follow the advice below to make sure that the data stored on your CDs/DVDs can be
accessed.
If you need to manually
eject a CD (e.g. due to Note the following:
an unexpected power
interruption) you may • Hold the CD or DVD by the edges; do not touch the surface of the disc.
push the end of a • Use a clean, soft, dry cloth to remove dust or fingerprints.
straightened paper clip
into the emergency eject
• Do not write on the surface with a pen.
hole. However please • Do not attach paper or other materials to the surface of the disc.
do NOT use a sharp- • Do not store or place the CD or DVD in high-temperature areas.
ened pencil or similar • Do not use benzene, thinner, or other cleaners to clean the CD or DVD.
object that may break
• Do not bend the CD or DVD.
and become lodged in
the hole. • Do not drop or subject the CD or DVD to shock.

Disk Eject Warning


Don’t try to remove a
CD/DVD while the sys-
tem is accessing it. This
may cause the system
to “crash”.

2 - 4 Optical (CD/DVD) Device


Features & Components

DVD Regional Codes


To change the DVD regional codes see “Changing DVD Regional Codes” on
2
page 1 - 14.
.

DVD Regional Coding


Table 2 - 1
Region Geographical Location DVD Regional Coding
1 USA, Canada

Western Europe, Japan, South


2
Africa, Middle East & Egypt
Figure 2 - 3
South-East Asia, Taiwan, South DVD Regions
3 Korea, The Philippines, Indonesia,
Hong Kong

South & Central America, Mexico,


4
Australia, New Zealand

N Korea, Russia, Eastern Europe,


5
India & Most of Africa
6 China

Optical (CD/DVD) Device 2 - 5


Features & Components

2 7-in-1 Card Reader


 The card reader allows you to use some of the latest digital storage cards. Push the
Card Reader Cover card into the slot and it will appear as a removable device, and can be accessed in
Make sure you keep the the same way as your hard disk (s). Make sure you install the PCMCIA/Card Reader
cover in the card reader driver (see “CardReader” on page 4 - 6).
when not in use. This
will help prevent foreign • MMC (MultiMedia Card) • MS Duo (requires PC adapter*)
objects and/or dust get- • SD (Secure Digital) • Mini SD (requires PC adapter*)
ting in to the card read- • MS (Memory Stick) • RS MMC (requires PC adapter*)
er.
• MS Pro (Memory Stick Pro)

*Note: The PC adapters are usually supplied with these cards.


Figure 2 - 4
Card Reader Model A - Left

1. Card Reader 1

Model B - Front

2 - 6 7-in-1 Card Reader


Features & Components

ExpressCard Slot 2
The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/

34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC ExpressCard
Cards). Slot Cover
Make sure you keep the
ExpressCard/54 is used for applications which require a larger interface slot, e.g. rubber cover provided in
CompactFlash card reader. The number denotes the card width; 54mm for the Ex- the ExpressCard slot
press Card/54 and 34mm for the ExpressCard/34. when not in use. This
will help prevent foreign
objects and/or dust get-
Inserting and Removing ExpressCards ting in to the Express-
• Align the ExpressCard with the slot and push it in until it locks into place. Card Slot.
• To remove an ExpressCard, simply press the card to eject it.

Figure 2 - 5
ExpressCard Slot

ExpressCard Slot 2 - 7
Features & Components

2 Application Hot Key


 The hot key buttons give instant access to the default Internet browser and e-mail
Application.exe program, and to a user-defined application, with one quick button press. To config-
You will need to locate ure a program to open when the application hot key is pressed (Windows Me-
the actual application dia Player is the default program), follow the instructions below.
executable (.exe) file,
not just the shortcut. To 1. Right click the hot key driver icon in the taskbar.
find the application right- 2. Select Setup from the menu, scroll to Application 1 and select Custom.
click its shortcut on the
desktop and click Prop-
erties. Click the short-
cut (tab) and see where
the executable file is lo-
cated by clicking the 3. An Open dialog box will appear on the screen.
Open File Location
(button).

Figure 2 - 6
Application Hot Key
Configuration
4. Click Look in: and browse to the directory where the desired application.exe (see
the sidebar) program exists.
5. Double-Click on the program file or choose Open.

2 - 8 Application Hot Key


Features & Components

TouchPad and Buttons/Mouse 2



The TouchPad is an alternative to the mouse; however, you can also add a mouse to
your computer through one of the USB ports. The TouchPad buttons function in Mouse Driver
much the same way as a two-button mouse. If you are using an ex-
ternal mouse your op-
Install the TouchPad driver (see “TouchPad” on page 4 - 6) and then double-click erating system may be
able to auto-configure
the TouchPad icon on the taskbar to configure the functions (tapping, buttons, your mouse during its
scrolling, pointer motion and sensitivity) to your preferences. Further information is installation or only en-
available at www.synaptics.com. able its basic functions.
Be sure to check the
device’s user docu-
mentation for details.

Figure 2 - 7
Mouse Properties

TouchPad and Buttons/Mouse 2 - 9


Features & Components

2 Audio Features

You can configure the audio options on your computer from the Sound control
Sound Volume
panel in Windows, or from the VIA Audio Deck icon in the taskbar, or on the
Adjustment
desktop (this will bring up the VIA Audio Deck menu). The volume may also be
The sound volume level adjusted by means of the Fn + F5/F6 key combination.
is set using the volume
control within Windows
(and the volume func-
Click any of the buttons (e.g. ) on the left to expand the audio menu selections.
tion keys on the comput-
er). Click the volume
icon in the taskbar to
check the setting.

Figure 2 - 8
VIA Audio Deck
Configuration
Menus

2 - 10 Audio Features
Features & Components

Adding a Printer 2
The most commonly used peripheral is a printer. The following conventions will

help you to add a printer, however it is always best to refer to the printer manual for Parallel Printer
specific instructions and configuration options. After setting up the print-
er attach the parallel ca-
USB Printer ble to the printer.

Most current printers have a USB interface connection. You may use any one of the Connect the printer’s
ports to connect the printer. parallel cable to the Par-
allel to USB converter,
Install Instructions: and then plug the con-
1. Set up the printer according to its instructions (unpacking, paper tray, toner/ink car- verter into the USB port.
tridge etc.).
2. Turn ON the computer. Turn ON the printer,
3. Turn ON the printer. then turn ON the com-
4. Connect the printer’s USB cable to one of the USB ports on the computer. puter.
5. Windows will identify the printer and either load one of its own drivers or ask you
Windows will identify the
to supply one. Follow the on-screen instructions. printer and either load
one of its own drivers or
Parallel Printer ask you to supply one.
Follow the on-screen in-
This is still a very common type of printer. The install instructions are in the sidebar. structions.

Adding a Printer 2 - 11
Features & Components

2 - 12
Power Management

Chapter 3: Power Management 


Overview OS Note
3
To conserve power, especially when using the battery, your computer power man- Power management
functions will vary slight-
agement conserves power by controlling individual components of the computer ly depending on your
(the monitor and hard disk drive) or the whole system. This chapter covers: operating system. For
more information it is
• The Power Sources best to refer to the user’s
manual of your operat-
• Turning on the Computer ing system.
• Power Plans
• System Power Options (Note: All pictures used
• Configuring the Power Buttons on the following pages
• Battery Information are from the Windows
Vista OS.)

The computer uses enhanced power saving techniques to give the operating system
(OS) direct control over the power and thermal states of devices and processors. For
example, this enables the OS to set devices into low-power states based on user set-
tings and information from applications.

Overview 3 - 1
Power Management

The Power Sources


The computer can be powered by either an AC/DC adapter or a battery pack.
3
AC/DC Adapter
Use only the AC/DC adapter that comes with your computer. The wrong type of AC/
DC adapter will damage the computer and its components.
1. Attach the AC/DC adapter to the DC-in jack on the right of the computer.
2. Plug the AC power cord into an outlet, and then connect the AC power cord to the
AC/DC adapter.
3. Raise the lid/LCD to a comfortable viewing angle.
4. Press the power button to turn “On”.

Battery
The battery allows you to use your computer while you are on the road or when an
electrical outlet is unavailable. Battery life varies depending on the applications and
the configuration you're using. To increase battery life, let the battery discharge
completely before recharging (see “How do I completely discharge the battery?”
on page 3 - 13).

We recommend that you do not remove the battery. For more information on the bat-
tery, please refer to “Battery Information” on page 3 - 9.

3 - 2 The Power Sources


Power Management

Turning on the Computer


Now you are ready to begin using your computer. To turn it on simply press the pow-

er button on the front panel. Shut Down
3
Note that you should al-
When the computer is on, you can use the power button as a Sleep/Hibernate hot- ways shut your comput-
key button when it is pressed for less than 4 seconds (pressing and holding the power er down by choosing the
button for longer than this will shut the computer down). Use Power Options Shut Down command
from the Lock Button
(Hardware and Sound menu) control panel in Windows Vista to configure this fea- Menu in Windows Vis-
ture. ta. This will help prevent
hard disk or system
problems.

Forced Off
If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the pow-
er button for 4 seconds, or longer, to force the system to turn itself off.

Power Button Sleep


Sleep is the default power mode when the power button is pressed for less than 4 seconds.
You may configure the options for the power button from the Power Options (Hardware
and Sound menu) control panel in Windows Vista (see your OS’s documentation, or
“Configuring the Power Buttons” on page 3 - 8 for details).

Turning on the Computer 3 - 3


Power Management

Power Plans
 The computer can be configured to conserve power by means of power plans. You
Resuming can use (or modify) an existing power plan, or create a new one.
3 Operation
The settings may be adjusted to set the display to turn off after a specified time, and
If the display is off the
system can resume by
to send the computer into Sleep after a period of inactivity.
pressing any key on the
keyboard.
Click Change plan settings and then click Change advanced power settings to ac-
cess further configuration options in Advanced Settings.
The system can resume
from Sleep mode by
pressing the Sleep But-
ton key combination (Fn
+ F4), or power button.

Password
It is recommended that
you enable a password
on system resume in or-
der to protect your data.

Figure 3 - 1
Power Plan
Advanced Settings

3 - 4 Power Plans
Power Management

Each Windows power plan will also adjust the processor performance of your ma-
chine in order to save power. This is worth bearing in mind if you are experiencing
any reduced performance (especially under DC/battery power).
3
Choose High performance for maximum performance when the computer is pow-
ered from an AC power source. Choose the Power saver (bear in mind that this
scheme may slow down the overall performance of the computer in order to save
power) for maximum power saving when the computer is battery (DC power) pow-
ered.

Figure 3 - 2
Power Plans

Power Plans 3 - 5
Power Management

System Power Options


 You can use the system power options to stop the computer’s operation and restart
Sleep Button where you left off. The system features Sleep and Hibernate power saving states
3
The Sleep Button (Hibernate will need to be enabled from power plan Advanced Settings see Figure
in the Start Menu (not 3 - 1 on page 3 - 4).
available in Classic
View) can be used to
send the computer into
Hibernate vs. Shut Down
Sleep. Hibernate and Shut Down are the same in that the system is off and you need to press
the power button to turn it on. Their main difference is:
Note that Sleep is the
default power saving When you come back from hibernation, you can return to where you last left off
state in Windows Vista. (what was on your desktop) without reopening the application(s) and file(s) you last
used.
You can use either method depending on your needs.

Sleep vs. Hibernate


If you want to stay away from your work for just a while, you can put the system into
Sleep instead of in hibernation. It takes a longer time to wake up the system from
Hibernate mode than from Sleep mode. Sleep will effectively act as Hibernate if
the computer battery becomes depleted (see “Sleep Mode & Mobile PC Battery” on
page 3 - 7).

3 - 6 System Power Options


Power Management

Sleep
Sleep uses very little system power, and takes a short time to return to full operation. 
After an extended period of time in Sleep the computer will save the contents of sys- Sleep Mode &
tem memory (e.g. any open documents and applications) to the hard disk and shut Mobile PC Battery
3
the system down. When you are not using your computer for a certain length of time,
A mobile PC in Sleep
which you specify in the operating system, it will enter Sleep mode to save power. uses very little battery
power.
Hibernate
After an extended peri-
Hibernate uses no power and saves all of your information on a part of the hard disk od of time the computer
before it turns the system off. Although it saves the most power it takes the longest will save any open docu-
time to return to full operation. You can set your computer to automatically enter Hi- ments and applications
bernate when the battery power is almost depleted. You will need to enable Hiber- to hard disk.
nate mode from the Advanced Settings in power plans, or you put the system
directly into Hibernate mode from the Lock Button Menu. The system will re-
sume from Hibernate mode by pressing the power button.

Figure 3 - 3
Lock Button Menu
Hibernate

System Power Options 3 - 7


Power Management

Configuring the Power Buttons


 The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the
Password computer in to either Sleep or Hibernate. In Sleep, the LED will blink green.
3 Protection In Hibernate the LED will be off (battery) or orange (AC/DC adapter). If only the
It is recommended that display is turned off, the LED will remain green.
you enable a password
on wake up in order to
protect your data.

However you can dis-


able this setting from the
Power Options menu
by clicking Require a
password on wakeup
in the left menu, and se-
lecting the options (click
Change settings that
are currently unavail-
able).

Figure 3 - 4
Power Options
Define Power
Buttons

3 - 8 Configuring the Power Buttons


Power Management

Battery Information
Please follow these simple guidelines to get the best use out of your battery.

Low Battery
Warning
3
Battery Power
Your computer’s battery power is dependent upon many factors, including the pro- When the battery is criti-
grams you are running, and peripheral devices attached. You can set actions to be cally low, immediately
connect the AC/DC
taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from adapter to the computer
power plan Advanced Settings (see Figure 3 - 1 on page 3 - 4). or save your work, oth-
erwise, the unsaved
Click the battery icon in the taskbar to see the current battery level and charge data will be lost when
the power is depleted.
status.

Figure 3 - 5
Battery Icon
(Taskbar) & Battery
Advanced Settings

Battery Information 3 - 9
Power Management

Conserving Battery Power


 • Use a power plan that conserves power (e.g Power saver), however note that
Windows Mobility this may have an affect on computer performance.
3 Center
• Lower the brightness level of the LCD display. The system will decrease LCD
The Windows Mobility
Center control panel pro- brightness slightly to save power when it is not powered by the AC/DC adapter.
vides an easy point of ac-
cess for information on • Reduce the amount of time before the display is turned off.
battery status, power plans
used and wireless device • Close wireless, Bluetooth, modem or communication applications when they are
status etc. not being used.
• Disconnect/remove any unnecessary external devices e.g. USB devices,
ExpressCards etc.

Figure 3 - 6
Windows Mobility
Center

3 - 10 Conserving Battery Power


Power Management

Battery Life
Battery life may be shortened through improper maintenance. To optimize the life
and improve its performance, fully discharge and recharge the battery at least 3
once every 30 days.
We recommend that you do not remove the battery yourself. If you do need to re-
move the battery for any reason see “Removing the Battery” on page 6 - 3.

New Battery
Always completely discharge, then fully charge, a new battery (see “Battery FAQ”
on page 3 - 13 for instructions on how to do this).

Recharging the Battery with the AC/DC Adapter


The battery pack automatically recharges when the AC/DC adapter is attached and
plugged into an electrical outlet. If the computer is powered on, and in use, it will
take several hours to fully recharge the battery. When the computer is turned off but
plugged into an electrical outlet, battery charge time is less. (Refer to “LED Indica-
tors” on page 1 - 9 for information on the battery charge status, and to “Battery In-
formation” on page 3 - 9 for more information on how to maintain and properly
recharge the battery pack.)

Battery Life 3 - 11
Power Management

Proper handling of the Battery Pack


 • DO NOT disassemble the battery pack under any circumstances
Caution • DO NOT expose the battery to fire or high temperatures, it may explode
3 • DO NOT connect the metal terminals (+, -) to each other
Danger of explosion if
battery is incorrectly re-
placed.

Replace only with the
same or equivalent type Damaged Battery Warning
recommended by the
Should you notice any physical defects (e.g. the battery is bent out of shape after being
manufacturer. Discard
dropped), or any unusual smells emanating from the notebook battery, shut your computer
used battery according
down immediately and contact your service center. If the battery has been dropped we do
to the manufacturer’s in-
not recommend using it any further, as even if the computer continues to work with a dam-
structions.
aged battery in place, it may cause circuit damage, which may possibly result in fire. It is
recommended that you replace your computer battery every two years.

3 - 12 Battery Life
Power Management

Battery FAQ
How do I completely discharge the battery?
Use the computer with battery power until it shuts down due to a low battery. Don’t
turn off the computer even if a message indicates the battery is critically low, just let 3
the computer use up all of the battery power and shut down on its own.
1. Save and close all files and applications.
2. Create a power plan for discharging the battery and set all the options to Never.
3. Click Change plan settings (after saving it) and click Change advanced power
settings.

Figure 3 - 7
Power Plan Create

Battery Life 3 - 13
Power Management

4. Scroll down to Battery and click + to expand the battery options.


5. Choose the options below (click Yes if a warning appears):

Figure 3 - 8
Power Options
Advanced Settings -
Battery

• Low battery levels = 0%


• Critical battery Levels = 0%
• Low battery action = Do Nothing
• Critical battery action (On battery) = Shut Down
• Critical battery action (Plugged in) = Do Nothing

3 - 14 Battery Life
Power Management

How do I fully charge the battery?


When charging the battery, don’t stop until the LED charging indicator light changes
from orange to green.
3
How do I maintain the battery?
Completely discharge and charge the battery at least once every 30 days or after
about 20 partial discharges.

Battery Life 3 - 15
Power Management

3 - 16
Drivers & Utilities

Chapter 4: Drivers & Utilities


This chapter deals with installing the drivers and utili- What to Install
ties essential to the operation or improvement of some
of the computer’s subsystems. The system takes ad- The Device Drivers & Utilities + User’s Manual CD-
ROM (Win Vista OR WinXP) contains the drivers and 4
vantage of some newer hardware components for
which the latest versions of most available operating utilities necessary for the proper operation of the com-
systems haven’t built in drivers and utilities. Thus, puter. There will be two CDs provided; one will con-
some of the system components won’t be auto-config- tain drivers for Windows Vista, the other will contain
ured with an appropriate driver or utility during oper- drivers for Windows XP (make sure you install the ap-
ating system installation. Instead, you need to propriate drivers for your system).
manually install some system-required drivers and
utilities. Table 4 - 1, on page 4 - 3 lists what you need to install
and it is very important that the drivers are in-
stalled in the order indicated.

Module Driver Installation


The procedures for installing drivers for the Wireless
LAN, Bluetooth, and PC Camera modules are pro-
vided in “Modules & Options” on page 7 - 1.

What to Install 4 - 1
Drivers & Utilities

Driver Installation 1. Check the driver installation order from Table 4 - 1,


on page 4 - 3 (the drivers must be installed in
Insert the Device Drivers & Utilities + User’s Manual this order) which is the same as that listed in the
CD-ROM and click Install Vista Drivers (button)/In- Drivers Installer menu below.
stall Option Drivers (button). 2. Click to select the driver you wish to install, after
installing each driver it will become grayed out (if
4 If you wish to install the drivers manually see page 4 - you need to reinstall any driver, click the Unlock
4. button).
3. Follow the instructions for each individual driver
installation procedure as listed on the following
pages.

Figure 4 - 1 - Drivers Installer Screen 1


Figure 4 - 2 - Drivers Installer Screen 2

4 - 2 Driver Installation
Drivers & Utilities

Updating/Reinstalling Individual Drivers


Driver Page #
If you wish to update/reinstall individual drivers it
Video Page 4 - 5 may be necessary to uninstall the original driver.To do
Audio Page 4 - 5 this go to the Control Panel in the Windows OS and
double-click the Programs and Features icon (Pro-
Modem Page 4 - 6
grams > Uninstall a program). Click to select the 4
LAN Page 4 - 6 driver (if it is not listed see below) and click Uninstall,
TouchPad Page 4 - 6 and then follow the on screen prompts (it may be nec-
CardReader Page 4 - 6 essary to restart the computer). Reinstall the driver as
outlined in this chapter.
Hot Key Page 4 - 6

Wireless LAN Page 7 - 2 If the driver is not listed in the Programs and Fea-
Bluetooth Page 7 - 7 tures menu:
PC Camera Page 7 - 11
1. Click Start, and click Control Panel (or point to
Settings and click Control Panel).
Table 4 - 1 - Driver Installation
2. Double-click Device Manager (Hardware and
Sound > Device Manager).
3. Double-click the device you wish to update/reinstall
the driver for (you may need to click “+” to expand
the selection).
4. Click Driver (tab) and click the Update Driver or
Uninstall button and follow the on screen prompts.

Driver Installation 4 - 3
Drivers & Utilities

Manual Driver Installation


If you wish to install the drivers manually, click the Exit button to quit the Drivers Installer application, and
then browse to the executable file in the location listed in the table below and follow the installation procedure
for each driver. Note that X is the drive letter assigned to the CD/DVD-ROM drive.
.
4 Driver Driver Location

Video Vista 32bit: X:\Drivers\01_Video\setup.exe

Audio Vista 32bit: X:\Drivers\02_Audio\SETUP.EXE

Modem Vista 32bit: X:\Drivers\03_Modem\ssetup.exe

LAN Vista 32bit: X:\Drivers\04_LAN\setupvis.exe

TouchPad Vista 32bit: X:\Drivers\05_Touchpad\WinWDF\x86\dpinst.exe

CardReader Vista 32bit: X:\Drivers\06_CardReader\Setup.exe

Hot Key Vista 32bit: X:\Drivers\07_Hotkey\1AP.exe

802.11 b/g USB WLAN Module Vista 32bit: X:\Drivers\Option\08_WLAN\Setup.exe

Bluetooth Module Vista 32bit: X:\Drivers\Option\09_Bluetooth\setup.exe

Vista 32bit: X:\Drivers\Option\10_Camera\setup.exe (for non UVC Cameras)


PC Camera Driver Installation
Vista 32bit: X:\Drivers\Option\11_UVC_Camera\setup.exe (for UVC Cameras)

Table 4 - 2 - Driver Location

4 - 4 Driver Installation
Drivers & Utilities

User Account Control (Win Vista) Driver Installation Procedure


If a User Account Control prompt appears as part of
the driver installation procedure, click Continue or Video
Allow, and follow the installation procedure as direct- 1. Click 1.Install Video Driver > Yes.
ed. 2. Click Next > Next. 4
3. Click Finish to restart the computer.
Windows Security Message
If you receive a Windows security message as part of Audio
the driver installation process. Just click “Install this
driver software anyway” or Install to continue the in- 1. Click 2.Install Audio Driver > Yes.
stallation procedure. 2. Click Next.
3. Click the button to accept the license and click
You will receive this message in cases where the driv- Next.
er has been released after the version of Windows you
4. Click Next > Next > Next.
are currently using. All the drivers provided will have
5. Click Finish to restart the computer.
already received certification for Windows.

New Hardware Found


If you see the message “New Hardware Found”
(Found New Hardware Wizard) during the installa-
tion procedure (other than when outlined in the driver
install procedure), click Cancel to close the window,
and follow the installation procedure as directed.

Driver Installation 4 - 5
Drivers & Utilities

Modem TouchPad
1. Click 3.Install Modem Driver > Yes. 1. Click 5.Install Touchpad Driver > Yes.
2. Click OK. 2. Click Next.
3. The modem is ready for dial-up configuration. 3. Click Finish > Restart Now to restart the com-
4 puter.
4. You may then configure your TouchPad as out-

lined in “TouchPad and Buttons/Mouse” on
Modem Country Selection
page 2 - 9.
Go to the Phone and Modem Options control panel
(Hardware and Sound) and make sure the modem
country selection is appropriate for you.
CardReader
1. Click 6.Install CardReader Driver > Yes.
2. Click Next > Next.
LAN 3. Click Finish to restart the computer.
1. Click 4.Install LAN Driver > Yes.
2. Click OK. Hot Key
3. The network settings can mow be configured. 1. Click 7.Install Hotkey Driver > Yes.
2. Click Next.
3. Click Finish to restart the computer.

4 - 6 Driver Installation
Drivers & Utilities

Wireless LAN
See the introduction in “802.11 b/g USB WLAN Mod-
ule” on page 7 - 2, and check the installation proce-
dure.

Bluetooth 4
See the introduction in “Bluetooth Module” on
page 7 - 7, and check the installation procedure.

PC Camera
See the introduction in “Bluetooth Local Area Con-
nection” on page 7 - 9, and check the installation pro-
cedure.

Driver Installation 4 - 7
Drivers & Utilities

4 - 8
BIOS Utilities

Chapter 5: BIOS Utilities 


Overview BIOS Settings
Warning
This chapter gives a brief introduction to the computer’s built-in software:
Incorrect settings can
cause your system to
The Setup utility malfunction. To correct
If your computer has never been set up, or you are making important changes to the mistakes, return to Set- 5
system (e.g. hard disk setup), then you should review this chapter first and note the up and restore the Set-
original settings found in Setup. Even if you are a beginner, keep a record of the set- up Defaults with <F9>.
tings you find and any changes you make. This information could be useful if your
system ever needs servicing.

There is one general rule: Don’t make any changes unless you are sure of what you
are doing. Many of the settings are required by the system, and changing them could
cause it to become unstable or worse. If you have any doubts, consult your service
representative.

Overview 5 - 1
BIOS Utilities

Startup Screen
Each time you turn on the computer, the system takes a few seconds to conduct tests
on memory, keyboard, mouse and system. As the boot proceeds, you can click the
mouse, or press Enter, and then choose “Launch System Setup” from the Trusted-
Core menu to access the PhoenixBIOS Setup Utility.
Figure 5 - 1
5 Startup Screen

5 - 2 Startup Screen
BIOS Utilities

In addition to accessing the Setup menus, you can also select a boot device, view
system information or setup a password for access to the computer at boot time (see
overleaf).
Launch System Setup Figure 5 - 2

TrustedCore
Select Boot Device Trusted Core Menu
Security Enrollment

Patent Inform
r ation 5
System Inform
r ation
Continue Booting

Startup Screen 5 - 3
BIOS Utilities

Setting a Boot Password


1. Use the mouse to select Security Enrollment from the menu. A Security Enroll-
ment screen similar to the screen below will then appear:

Figure 5 - 3 Secu
c rity
t En
Enrollm
lment
Security Enrollment
Enter your new password and confirm
r it.
Adm
d inistrator privileges
5 Password:

New:

 Confirm
r :

Password Warning
If you set a boot pass-
2. Type in the New Password, and then type it again to Confirm the new password.
word NEVER forget
3. Click OK to set the password.
your password.
4. You will now be prompted to enter the password when the computer boots up.
The consequences of
this could be serious. If Note: To clear existing passwords follow the procedure above to bring up the Secu-
you cannot remember rity Enrollment screen and type the existing password. Press Enter (without typing
your boot password you
must contact your ven- any password entry) and click Yes to un-enroll.
dor and you may lose all
of the information on
your hard disk.

5 - 4 Startup Screen
BIOS Utilities

Setup Screens
The following pages contain additional advice on portions of the Setup. 
Setup Menus
Along the top of the screen is a menu bar with four (4) menu headings. When you
select a heading, a new screen appears. Scroll through the features listed on each The Setup menus
shown in this section are
screen to make changes to Setup. for reference only. Your
computer’s menus will
Instructions on how to navigate each screen are in the box along the bottom of the indicate the configura- 5
screen. If these tools are confusing, press F1 to call up a General Help screen, and tion appropriate for your
model and options.
then use the arrow keys to scroll up or down the page.

The Item Specific Help on the right side of each screen explains the highlighted
item and has useful messages about its options.

If you see an arrow next to an item, press Enter to go to a sub-menu on that sub-
ject. The sub-menu screen that appears has a similar layout, but the Enter key may
execute a command.

Startup Screen 5 - 5
BIOS Utilities

Main Menu
Figure 5 - 4 PhoenixBIOS Setup Utility
Main Menu Main
Main Advanced Boot Exit

Item Specific Help


System Time: [22:11:05]
06
System Date: [01/10/2007]

5 IDE Channel 0 Master


IDE Channel 2 Master
[TSSTcorpCD/DVDW TS-L632D-]
[FUJITSU MHW2060BH-(S1)]
<Tab>, <Shift Tab>, or
<Enter> selects field.

System Memory 633 KB


Extended Memory 894 MB

F1 Help  Select Item -/+ Change Values F9 Setup Defaults


Esc Exit  Select Menu Enter Select Sub-Menu F10 Save and Exit

System Time & Date (Main Menu)


The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you
can change the date and time settings in your operating system, you will also change
these settings. Some applications may also alter data files to reflect these changes.

5 - 6 Main Menu
BIOS Utilities

IDE Channel 0/2 Master (Main Menu)


Pressing Enter opens the sub-menu to show the configuration of either a DVD/CD
Device or HDD on the computer’s IDE Channels. Use the Auto (Type:) setting to
have the items configured automatically for you.

System/Extended Memory: (Main Menu)


This item contains information on the system memory, and is not user configurable.
The system will auto detect the amount of memory installed. 5

Main Menu 5 - 7
BIOS Utilities

Advanced Menu
Figure 5 - 5 PhoenixBIOS Setup Utility
Advanced Menu
Main Advanced
Advanced Boot Exit

Item Specific Help

Installed O/S: [WinXP/Vista] Select the operating


Legacy USB Support: [Enabled]
5 Reset Configuration Data: [No]
system installed
on your system which
Enable Multimedia Timer: [No] you will use most
Frame Buffer Size: [128MB] commonly.

Note: An incorrect
setting can cause
some operating
systems to display
unexpected behavior.

F1 Help  Select Item -/+ Change Values F9 Setup Defaults


Esc Exit  Select Menu Enter Select Sub-Menu F10 Save and Exit

Installed O/S: (Advanced Menu)


This setting tells the computer what kind of operating system you’re using.

5 - 8 Advanced Menu
BIOS Utilities

Legacy USB Support: (Advanced Menu)


Choose “Enabled” if you intend to use USB devices in systems which do not nor-
mally support USB functionality (e.g. DOS). The default setting is “Enabled” and
does not need to be changed if you intend to use your USB devices in Windows.

Reset Configuration Data: (Advanced Menu)


This item is set to No as default. You can change the setting to Yes if you have in-
stalled a new add-on which has reconfigured the system, resulting in such a serious 5
system conflict that the operating system is unable to boot.

Enable Multimedia Timer: (Advanced Menu)


Multimedia timer services allow applications to schedule timer events with the
greatest resolution (or accuracy) possible for the hardware platform. These timer ser-
vices are useful for applications that demand high-resolution timing (see your appli-
cation manual for further details). This item is set to Disabled as default.

Frame Buffer Size: (Advanced Menu)


Use this menu item to set the amount of system memory to be allocated for use by
the integrated graphic system. The default memory size allocated is 128MB, and this
may be adjusted to 64MB or 256MB if required.

Advanced Menu 5 - 9
BIOS Utilities

Boot Menu
PhoenixBIOS Setup Utility
Figure 5 - 6
Boot Menu Main Advanced Boot Exit

Item Specific Help


Boot priority order:
1: IDE 0: TSSTcorpCD/DVDW TS-L632D-( Keys used to view or
2: IDE 4: FUJITSU MHW2060BH-(S1) configure devices:
5 3: USB FDC:
4: USB KEY:
Up and Down arrows
select a device.
5: USB HDD:
<+> and <-> moves
6: PCI BEV: VIA Boot Agent
7: the device up or down.
8: <x> exclude or include
Excluded from boot order: the device to boot.
: USB CDROM: <Shift +1> enables or
: USB ZIP disables a device.
: USB LS120 <1 - 4> Loads default
: PCI SCSI boot sequence.

F1 Help  Select Item -/+ Change Values F9 Setup Defaults


Esc Exit  Select Menu Enter Select Sub-Menu F10 Save and Exit

When you turn the computer on it will look for an operating system (e.g. Win-
dowsXP) from the devices listed in this menu, and in this priority order. If it cannot
find the operating system on that device, it will try to load it from the next device in
the order specified in the Boot priority order. Item specific help on the right is
available to help you move devices up and down the order.

5 - 10 Boot Menu
BIOS Utilities

Exit Menu
PhoenixBIOS Setup Utility Figure 5 - 7
Exit Menu
Main Advanced Security Boot Exit
Exit

Item Specific Help


Exit Saving Changes
Exit Discarding Changes Exit System Setup and
Load Setup Defaults save your changes to
CMOS.
5
Discard Changes
Save Changes

F1 Help  Select Item -/+ Change Values F9 Setup Defaults


Esc Exit  Select Menu Enter Execute Command F10 Save and Exit

Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any
changes you have made to the Setup. You can also choose to restore the original Set-
up defaults that will return the Setup to its original state, and erase any previous
changes you have made in a previous session.

Exit Menu 5 - 11
BIOS Utilities

5 - 12
Upgrading The Computer

Chapter 6: Upgrading The Computer 


Overview Warranty Warning

This chapter contains information on upgrading the computer. Follow the steps out- Please check with your
service representative
lined to make the desired upgrades. If you have any trouble or problems you can con- before undertaking any
tact your service representative for further help. Before you begin you will need: upgrade procedures to
find out if this will VOID
• A small crosshead or Phillips screwdriver your warranty.
• A small regular slotted (flathead) screwdriver 6
• An antistatic wrist strap
Before working with the internal components you will need to wear an antistatic 
wrist strap to ground yourself because static electricity may damage the compo-
Note
nents.
Note that the disassem-
The chapter includes: bly pictures are correct
at time of going to press.
• Removing the Battery However computer de-
• Upgrading the Hard Disk Drive signs are subject to con-
• Upgrading the Optical (CD/DVD) Device tinual updates and
• Upgrading the System Memory (RAM) changes, and some
models may appear
Please make sure that you review each procedure before you perform it. slightly different from
those pictured.

Overview 6 - 1
Upgrading The Computer

When Not to Upgrade


 These procedures involve opening the system’s case, adding and sometimes replac-
Power Safety ing parts.
Warning
You should not perform any of these upgrades if:
Before you undertake
any upgrade proce- • Your system is still under warranty or a service contract
dures, make sure that
you have turned off the
• You don’t have all the necessary equipment
power, and disconnect- • You’re not in the correct environment
6 ed all peripherals and • You doubt your abilities
cables (including tele-
phone lines). It is advis- Under any of these conditions, contact your service representative to purchase or re-
able to also remove your
battery in order to pre- place the component(s).
vent accidentally turning
the machine on. 
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upgrade, remember
to replace the cover(s) and screw(s) before turning the computer on.

6 - 2 Overview
Upgrading The Computer

Removing the Battery


If you are confident in undertaking upgrade procedures yourself, for safety reasons

it is best to remove the battery. Warranty Warning
1. Turn the computer off, and turn it over. Please check with your
2. Slide the latch 1 in the direction of the arrow, and hold it in place. service representative
3. Slide the battery in the direction of the arrow 2 . before undertaking any
upgrade procedures to
find out if this will VOID
your warranty.
1 1
6
Figure 6 - 1
Battery Latch
Model A Model B

Removing the Battery 6 - 3


Upgrading The Computer

4. Lift the battery out in the direction of the arrow 3 .

Figure 6 - 2
Battery Up

3
6
5. Lift the battery 4 out.

Figure 6 - 3
Battery Out
4

6 - 4 Removing the Battery


Upgrading The Computer

Upgrading the Hard Disk Drive


The hard disk drive can be taken out to accommodate other 2.5" serial (SATA) hard

disk drives with a height of 9.5mm (h) (see “Storage” on page C - 3). Follow your HDD System
operating system’s installation instructions, and install all necessary drivers and util- Warning
ities (as outlined in “Driver Installation” on page 4 - 2), when setting up a new hard New HDD’s are blank. Be-
disk. fore you begin make sure:
You have backed up any
1. Turn off the computer, and turn it over and remove the battery. data you want to keep from
your old HDD.
2. Locate the hard disk bay cover and remove screw 1 (Model A) or screws 2 & You have all the CD-ROMs
3 (Model B). and FDDs required to in- 6
stall your operating system
and programs.
If you have access to the in-
ternet, download the latest
Model A Model B application and hardware
driver updates for the oper-
ating system you plan to in-
stall. Copy these to a
removable medium.
1
2 3
Figure 6 - 4
Hard Disk Bay &
Screw(s)

Upgrading the Hard Disk Drive 6 - 5


Upgrading The Computer

For Model A computers:


3. Slide the hard disk and cover assembly in the direction of arrow 4 .
4. Lift the hard disk and cover assembly up in the direction of arrow 5 .
5. Remove the hard disk and cover assembly 6 .

Figure 6 - 5 Model A
HDD & Cover
Assembly 4
Removal
6 (Model A
Computers Only)

5
6

6 - 6 Upgrading the Hard Disk Drive


Upgrading The Computer

6. Remove the screws 7 - 10 to release the hard disk 11 from the assembly cover
12 , and reverse the process to install any new hard disk.

10

9 Figure 6 - 6
Model A HDD Assembly
Cover Removal
(Model A
12 6
Computers Only)

11

Upgrading the Hard Disk Drive 6 - 7


Upgrading The Computer

For Model B computers:


7. Remove the cover 7 .
8. Pull the tab to slide the hard disk and case assembly in the direction of arrow 8 .
9. Lift the hard disk and case assembly out of the bay in the direction of arrow 9 .
10. Remove screws 10 & 11 to release the hard disk 12 from the case 13 , and
reverse the process to install any new hard disk.

6 8
Figure 6 - 7
HDD & Case
Assembly 11
Removal 13
7
(Model B
Computers Only) Model B
10 12

6 - 8 Upgrading the Hard Disk Drive


Upgrading The Computer

Upgrading the Optical (CD/DVD) Device


1. Turn off the computer, and turn it over and remove the battery.
2. Remove screws 1 - 7 (Model A)/ 1 - 5 (Model B), and remove the
component bay cover 8 .

Model A 3 4 Model B 2 3
2
1
1
5 5 6
4
7 6
Figure 6 - 8
Removing the
Component Bay
Cover

8 8

Upgrading the Optical (CD/DVD) Device 6 - 9


Upgrading The Computer

3. Use a screwdriver to carefully push out the optical device at point 9 .


4. Reverse the process to install the new device.

6
9

Figure 6 - 9
Removing the
Optical (CD/DVD)
Device

6 - 10 Upgrading the Optical (CD/DVD) Device


Upgrading The Computer

Upgrading the System Memory (RAM)


Model A computers have TWO memory sockets (Model B computers have ONE
memory socket) for 200 pin Small Outline Dual In-line (SO-DIMM) DDR2
(DDRII) type memory modules (see “Memory” on page C - 2 for details of support-
ed module types).
1. Turn off the computer, and turn it over and remove the battery.
2. Remove screws 1 - 7 (Model A)/ 1 - 5 (Model B), and remove the
component bay cover 8 .
6
Model A 3 4 Model B
2 2 3
Figure 6 - 10
1 1
5 5 Removing the
Component Bay
4 Cover
7 6

8 8

Upgrading the System Memory (RAM) 6 - 11


Upgrading The Computer

3. Locate the RAM socket(s) 9 .


Model A (2 RAM Sockets) Model B (1 RAM Socket)

Figure 6 - 11
RAM Socket
Location

9 9

6 4. Gently pull the two release latches on the sides of the memory socket in the
direction indicated by the arrows ( 10 & 11 ).
Model A (2 RAM Sockets) Model B (1 RAM Socket)

Figure 6 - 12
RAM Socket
Release Latches

10 11
10 11

6 - 12 Upgrading the System Memory (RAM)


Upgrading The Computer

5. The RAM module will 11 pop-up, and you can remove it.
Model A (2 RAM Sockets) Model B (1 RAM Socket) 
Contact Warning
Be careful not to touch
the metal pins on the
module’s connecting
11 11 11 edge. Even the cleanest
hands have oils which
can attract particles, and
degrade the module’s
performance.
6

6. Pull the latches to release the second module (Model A only) if necessary.
7. Insert a new module holding it at about a 30° angle and fit the connectors firmly Figure 6 - 13
into the memory slot. RAM Module
8. The module’s pin alignment will allow it to only fit one way. Make sure the module Removal
is seated as far into the slot as it will go. DO NOT FORCE the module; it should fit
without much pressure.
9. Press the module in and down towards the mainboard until the slot levers click into
place to secure the module.
10. Replace the component bay cover and screws.
11. Restart the computer to allow the BIOS to register the new memory configuration
as it starts up.

Upgrading the System Memory (RAM) 6 - 13


Upgrading The Computer

Upgrading the Processor


 If you want to upgrade your computer by replacing the existing processor with a fast-
Warranty er/new one you will need to contact your customer service representative. We rec-
The CPU is not a user ommend that you do not do this yourself, since if it is done incorrectly you may
serviceable part. Open- damage the processor or mainboard.
ing this compartment, or
accessing the CPU in
any way, may violate
your warranty.
6 Unauthorized tampering
with the HDD may also
violate your warranty.

6 - 14
Modules & Options

Chapter 7: Modules & Options 


Wireless Device
Overview Operation Aboard
This chapter contains information on the following modules, which may come with Aircraft
your computer, depending on the configuration purchased. If you are unsure please The use of any portable
contact your service representative. electronic transmission
devices aboard aircraft
• 802.11 b/g USB WLAN Module is usually prohibited.
• Bluetooth Module Make sure the mod-
ule(s) are OFF if you are
• PC Camera Module using the computer
aboard aircraft. 7

Overview 7 - 1
Modules & Options

802.11 b/g USB WLAN Module


 Before installing the 802.11b/g USB WLAN driver, make sure that the Wireless
Wireless Device LAN module is on. Use the Fn + F11 key combination (see “Function Keys” on
Operation Aboard
page 1 - 11) to toggle power to the Wireless LAN module. Make sure you install
Aircraft
the drivers in the order indicated in Table 4 - 1, on page 4 - 3.
The use of any portable
electronic transmission de-
vices aboard aircraft is usu-
802.11 b/g WLAN Driver Installation
ally prohibited. Make sure 1. Make sure the module is powered on, and then insert the Device Drivers &
the module(s) are OFF if
you are using the computer
Utilities + User’s Manual CD-ROM into the CD/DVD drive.
aboard aircraft. 2. Click Install Option Drivers (button).
7 3. Click 1.Install WLAN Driver > Yes.
Use the Fn + F11 key com-
bination to toggle power to 4. Click Finish to complete the installation.
the WLAN module, and 5. The operating system is the default setting for Wireless LAN control in
check the indicator to see if Windows Vista (see overleaf).
the module is powered on
or not (see Table 1 - 3, on
page 1 - 9/Table 1 - 6, on
page 1 - 11).

7 - 2 802.11 b/g USB WLAN Module


Modules & Options

Connecting to a Wireless Network


Make sure the Wireless LAN module is turned on.
1. Click the taskbar wireless icon , and then click Connect to a network (or right-
click the icon , and then click Connect to a network).
Figure 7 - 1
Taskbar Menus

Click icon Right-click icon



Network and
2. In the Show list, click to choose Wireless from the drop-down menu.
Sharing Center
3. A list of currently available networks will appear. 7
You can also use the
Network and Sharing
Center control panel in
Windows (Network and
Internet) to connect to
any available wireless
networks.

Figure 7 - 2
Connect to a
Network

802.11 b/g USB WLAN Module 7 - 3


Modules & Options

4. Click a network, and then click Connect.


5. If you do not see a network you want to connect to, click Set up a connection or
network (a list of options will appear allowing manual searching, and creating a
new network).
Figure 7 - 3
Connecting

6. Move the cursor over the taskbar icon to see the connection status (see below).

Figure 7 - 4
Connection Status

7 - 4 802.11 b/g USB WLAN Module


Modules & Options

7. To disconnect from the wireless network you can click the taskbar wireless icon
, and then select Connect or disconnect to access the network menu, and 
click Disconnect (or right-click the icon , and then click Disconnect from).
Security Enabled
Networks
You should try to make
sure that any network you
Click icon
are connecting to is a se-
cure network.

Connecting to unsecure net-


works may allow unautho-
rized access to your
computer, documents, web-
sites and files etc. 7

Figure 7 - 5
Disconnecting

Right-click icon

802.11 b/g USB WLAN Module 7 - 5


Modules & Options

Windows Mobility Center


The Windows Mobility Center control panel provides an easy point of access for
information on battery status, power plans used and wireless device status etc.

To access the Windows Mobility Center:


1. Click Start, and click Control Panel (or point to Settings and click Control
Panel).
2. Double-click Windows Mobility Center (Mobile PC).
3. Click the button to Turn wireless off/on, or click the icon to access the network
menu.

7 Figure 7 - 6
Windows Mobility
Center

7 - 6 802.11 b/g USB WLAN Module


Modules & Options

Bluetooth Module
Before installing the Bluetooth driver, make sure that the optional Bluetooth mod-

ule is on. Use the Fn + F12 key combination (see “Function Keys” on page 1 - 11) Wireless Device
Operation Aboard
to toggle power to the Bluetooth module. Make sure you install the drivers in the
Aircraft
order indicated in Table 4 - 1, on page 4 - 3.
The use of any portable
electronic transmission de-
Bluetooth Driver Installation vices aboard aircraft is usu-
1. Make sure the module is powered on, and then insert the Device Drivers & ally prohibited. Make sure
the module(s) are OFF if
Utilities + User’s Manual CD-ROM into the CD/DVD drive. you are using the computer
2. Click Install Option Drivers (button). aboard aircraft.
3. Click 2.Install Bluetooth Driver > Yes. 7
Use the Fn + F12 key com-
4. Choose the language you prefer, and click OK > Next. bination to toggle power to
5. Click the button to accept the license agreement, and then click Next. the Bluetooth module, and
6. Click Next > Install. check the indicator to see if
the module is powered on
7. Click Finish, and the BlueSoleil icon will appear on the desktop. or not (see Table 1 - 3, on
8. You can configure the settings at any time by going to the IVT Corpora- page 1 - 9/Table 1 - 6, on
tion BlueSoleil - Main Window (Start > Programs/All Programs > IVT page 1 - 11).

BlueSoleil > BlueSoleil), or by clicking the desktop icon .

Bluetooth Module 7 - 7
Modules & Options


User Guides & Help
View the BlueSoleil
User Guides from the
Help Menu (or press the
F1 key) in the IVT Cor-
poration BlueSoleil -
Main Window control
panel.

Click the Help menu


7 and select Contents
and Index.

Look through Getting


Started or select the ap-
propriate User Guide
from the Contents
menu.

Figure 7 - 7
BlueSoleil Main
Window & Help

7 - 8 Bluetooth Module
Modules & Options

Bluetooth Local Area Connection


You can check the Bluetooth connection status from the Network and Sharing 
Center: Disconnecting
1. Use the Fn + F12 key combination to turn on the Bluetooth module. In order to have the Local
2. Run the IVT Corporation BlueSoleil program from the desktop icon or Start menu. Area Connection icon dis-
3. Click Start, and click Control Panel (or point to Settings and click Control Panel). play the correct connection
4. Double-click Network and Sharing Center (Network and Internet). status, you will need to exit
the IVT Corporation Blue-
5. Click Manage network connections. Soleil - Main Window by
6. The Bluetooth connection status will then be displayed in the control panel. clicking the File menu and
selecting Exit (see over).

After exiting the program


you can then use the Fn +
F12 key combination to
7
turn off the Bluetooth mod-
ule.

If you use the close button,


or turn off the Bluetooth
module (by using the Fn +
F12) the icon will not dis-
play the correct status

Figure 7 - 8
7. To disconnect click File from the IVT Corporation BlueSoleil - Main Window, Local Area
and select Exit (the Local Area Connection will then display “Network cable Connection
unplugged”).

Bluetooth Module 7 - 9
Modules & Options

8. Do not use the close button or Fn + F12 key combination before clicking File >
Exit or the correct status will not be displayed.
9. You can then use the Fn + F12 key combination to turn off the Bluetooth module
(check the LED icon for the Bluetooth module power status).

7 Figure 7 - 9
Bluetooth
Disconnected

7 - 10 Bluetooth Module
Modules & Options

PC Camera Module
There are 3 (300K or 1.3M pixel) camera options available for this computer, de-

pending on your purchase configuration. The 1.3M pixel camera module has both Latest PC Camera
Driver Information
UVC (USB Video Class) and non UVC options.
Check the CD, and any
Before installing the PC Camera driver, make sure that the optional PC Camera is accompanying insert
on. Use the Fn + F10 key combination (see “Function Keys” on page 1 - 11) to pages for the latest up-
dated information on the
toggle power to the PC Camera module. Make sure you install the drivers in the PC Camera driver, that
order indicated in Table 4 - 1, on page 4 - 3. may override the infor-
mation provided here.
PC Camera Driver Installation
7
1. Make sure the module is powered on, and then insert the Device Drivers &
Utilities + User’s Manual CD-ROM into the CD/DVD drive.
2. Click Install Option Drivers (button).
3. Click 3.Install Camera Driver > Yes.
4. Choose the language you prefer and click Next > Next.
5. Click Finish to restart the computer.
6. Run the BisonCap application program from the BisonCam shortcut on the
desktop, or from the BisonCam item in the Start > Programs/All Pro-
grams menu (if the hardware is turned off use the Fn + F10 key combina-
tion to turn it on again).

PC Camera Module 7 - 11
Modules & Options

PC Camera Audio Setup


If you wish to capture video & audio with your camera, it is necessary to setup the
audio recording options in Windows.

1. Click Start, and click Control Panel (or point to Settings and click Control Panel).
2. Click Sound (Hardware and Sound).
3. Click Recording (tab).
4. Right-click Microphone (VIA High Definition Audio) and make sure the item is not
disabled (if you wish to record from the internal microphone make sure that the
Front Mic is not disabled).
5. Double-click Microphone/Front Mic (or select Properties from the right-click
menu).
7 6. Click Levels (tab), and adjust the Microphone/Front Mic slider to the level
required.
7. Click OK and close the control panels.
8. Run the BisonCap application program from the Start > Programs/All Programs
> BisonCam menu.
9. Go to the Devices menu heading and select the appropriate recording device (it
should have a tick alongside it) e.g Front Mic (VIA High Definition).... or
Microphone (VIA High Definition).... .
10. Go to the Capture menu heading and select Capture Audio (it should have a tick
alongside it).

7 - 12 PC Camera Module
Modules & Options

Figure 7 - 10
Audio Setup for PC
Camera

Right-click

PC Camera Module 7 - 13
Modules & Options

BisonCap
 BisonCap is a video viewer useful for general purpose video viewing and testing,
Pre-Allocating File
and can capture video files to .avi format.
Space
1. Run the BisonCap application from the Start > Programs/All Programs > Bison-
You may pre-allocate the Cam menu (it is recommended that you set the capture file before the capture
file size for the capture file process - see Set Capture File below).
in the BisonCap applica- 2. Go to the Capture menu heading (if you wish to capture audio check “PC Camera
tion. You can choose to Audio Setup” on page 7 - 12) and select Start Capture.
ignore this by clicking
3. On the first run of the program (if you have not set the captured file) you will be
Cancel.
asked to choose a file name and size (see the sidebar - Pre-Allocating File
Pre-allocating space on Space) for the captured file. Click Start Capture again.
7 the hard disk can improve 4. Click OK to start capturing the video, and press Esc to stop the capture.
the capture quality (par- 5. If you wish to, you may go to the File menu and select Save Captured Video
ticularly of large capture As..., choose a file name and location, and then click Open (you can view the file
files), by reducing the using the Windows Media Player).
amount of work the hard
disk has to do in finding
space for the video data Set Capture File
as it is being captured. In the BisonCap application you will only be asked to set the capture file name on
You may find it helpful to
the first run of the program. When you run the program the next time the file will
defragment the HDD be- automatically be overwritten with the newly captured file. To avoid overwriting files
fore capture. you can go to the Set Capture File.. option in the File menu, and set the file name
and location before capture. Set the name and location then click Open (you can
choose Cancel to ignore the file size if prompted).

7 - 14 PC Camera Module
Modules & Options

Eliminating Screen Flicker


If you find that the video screen in the BisonCap application is flickering, you can
try to adjust the setting in the Video Capture Filter options.
1. Run the BisonCap program.
2. Go to Options and scroll down to select “Video Capture Filter...”.
3. Click either 50Hz or 60Hz under Frequency in Property Page (tab).

Figure 7 - 11
Video Capture Filter
7

PC Camera Module 7 - 15
Modules & Options

7 - 16
Troubleshooting

Chapter 8: Troubleshooting
Overview
Should you have any problems with your computer, before consulting your service representative, you may want
to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This
can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these
pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
If all else fails, talk to your service representative. You should also make a record of what happened and what
remedies you tried.

Of course, if something goes wrong, it will happen at the most inconvenient time possible, so you should preview
this section just in case. If, after you’ve tried everything, and the system still won’t cooperate, try turning it off
for a few minutes and then rebooting. You will lose any unsaved data, but it may start working again. Then call 8
your service representative.

Overview 8 - 1
Troubleshooting

Basic Hints and Tips


Many of the following may seem obvious but they are often the solution to a problem when your computer ap-
pears not to be working.
• Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip,
make sure it is actually working. Check the LED Indicators (see “LED Indicators” on page 1 - 9) to see
the computer’s power status.
• Connections - Check all the cables to make sure that there are no loose connections anywhere.
• Power Savings - Make sure that the system is not in Hibernate or Sleep mode by pressing the keys config-
ured in your Power Options (see “Configuring the Power Buttons” on page 3 - 8), the Fn + F4 key combi-
nation, or power button to wake-up the system.

8 • Brightness - Check the brightness of the screen by pressing the Fn + F8 and F9 keys to adjust the bright-
ness.
• Display Choice - Press Fn + F7 to make sure the system is not set to “external only” display.
• Boot Drive - Make sure there are no optical media and/or USB storage devices in any connected drive
when you start up your machine (this is a common cause of the message “Invalid system disk - Replace the
disk, and then press any key” / “Remove disks or other media. Press any key to restart”).

8 - 2 Basic Hints and Tips


Troubleshooting

Backup and General Maintenance


• Always backup your important data, and keep copies of your OS and programs safe, but close to hand.
Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wal-
let.

• Run maintenance programs on your hard disk and OS as often as you can. You may schedule these pro-
grams to run at times when you are not using your computer. You can use those that are provided free with
your OS, or buy the more powerful dedicated programs to do so.

• Write down your passwords and keep them safe (away from your computer). This is especially important if
you choose to use a Supervisor password for the BIOS (see “Setting a Boot Password” on page 5 - 4).

• Keep copies of vital settings files such as network, dialup settings, mail settings etc.(even if just brief notes).
8

Warranty
The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your war-
ranty.

Backup and General Maintenance 8 - 3


Troubleshooting

Viruses
• Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses
to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm
your computer and cause you to lose data. Anti-Virus programs are commercially available and the defini-
tions file updates are usually downloadable directly from the internet.

• Be careful when opening e-mail from sources you don’t know. Viruses are often triggered from within e-
mail attachments so take care when opening any attached file. You can configure most Anti-Virus pro-
grams to check all e-mail attachments. Note: You should also beware of files from people you know as the
virus may have infected an address book and been automatically forwarded without the person’s knowl-
edge.

• Keep a “Bootable CD-ROM/DVD-ROM/USB storage device” (this CD/DVD/USB device provides basic
8 information which allows you to startup your computer) handy. You may refer to your OS’s documentation
for instructions on how to make one, and many Anti-Virus programs will also provide such a disk (or at
least instructions on how to make one).

8 - 4 Viruses
Troubleshooting

Upgrading and Adding New Hardware/Software


• Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are
doing, otherwise you will risk severely damaging your system.

• Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what
you are doing.

• Read the documentation. We can assume, since you are reading this that you are looking at the computer’s
manual, but what about any new peripheral devices you have just purchased? Many problems are caused by
the installation of new hardware and/or software. Always refer to the documentation of any new hardware
and/or software, and pay particular attention to files entitled “READ ME” or “READ ME FIRST”.

• When installing a new device always make sure the device is powered on, and in many cases you will need
to restart the computer. Always check that all the cables are correctly connected. 8

• Make sure you have installed the drivers for any new hardware you have installed (latest driver files are
usually available to download from vendor’s websites).

Upgrading and Adding New Hardware/Software 8 - 5


Troubleshooting

• Thoroughly check any recent changes you made to your system as these changes may affect one or more
system components, or software programs. If possible, go back and undo the change you just made and see
if the problem still occurs.
• Don’t over complicate things. The less you have to deal with then the easier the source of the problem may
be found; Example - if your computer has many devices plugged into its ports, and a number of programs
running, then it will be difficult to determine the cause of a problem. Try disconnecting all of the devices and
restarting the computer with all the peripheral devices unplugged. A process of elimination (adding and
removing devices and restarting where necessary) will often find the source of a problem, although this may
be time consuming.

8 - 6 Upgrading and Adding New Hardware/Software


Troubleshooting

Problems and Possible Solutions


Problem Possible Cause - Solution

You turned on the power Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and
but it doesn’t work. seated properly (the design of the battery only allows it to go in one way). Make sure there’s
nothing interfering with the battery contacts.

The battery LED power Low Battery. Plug in the DC power source. If the computer doesn’t start up immediately, turn it off
indicator , is blinking then on again.
orange.

You are losing battery The system is using too much power. If your OS has a Power Options scheme (see “Power
power too quickly. Plans” on page 3 - 4/“Power Schemes” on page D - 18) check its settings. You may also be
using an PC Card/ExpressCard device/USB device/external device that is drawing a lot of power.

Actual battery operating The battery has not been fully discharged before being recharged. Make sure the battery is fully 8
time is shorter than discharged and recharge it completely before reusing (see “Battery Information” on page 3 - 9/
expected. “Battery Information” on page D - 23).
Power Options have been disabled. Go to the Control Panel in Windows and re-enable the
options.
A peripheral device/USB device/Express Card is consuming a lot of power. Turn off/remove the
unused device to save power.

Problems and Possible Solutions 8 - 7


Troubleshooting

Problem Possible Cause - Solution

The computer feels too Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this
hot. doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the
computer isn’t sitting on a thermal surface (see “Overheating” on page 1 - 15). Make sure
you’re using the correct adapter.

Make sure that your notebook is completely powered off before putting it into a travel bag (or any
such container). Putting a notebook which is powered on in a travel bag may cause the Vent/Fan
intakes to be blocked.

Nothing appears on The system is in a power saving mode. Toggle the sleep/resume key combination, Fn + F4 (see
screen. “Sleep Button” on page 3 - 6/“Sleep Button” on page D - 22).

The screen controls need to be adjusted. Toggle the screen control key combinations Fn + F8/F9.
If you’re connected to an external monitor, make sure it’s plugged in and turned on. You should
8 also check the monitor’s own brightness and contrast controls.

The computer is set for a different display. Toggle the screen display key combination, Fn + F7. If
an external monitor is connected, turn it on.

The screen saver is activated. Press any key or touch the TouchPad.

No image appears on the You haven’t installed the video driver and configured it appropriately from the Control Panel. See
external monitor I have “Advanced Video Controls” on page B - 2/“Advanced Video Controls” on page D - 8 for
plugged in and powered instructions on configuring the video driver.
on.

8 - 8 Problems and Possible Solutions


Troubleshooting

Problem Possible Cause - Solution

You forget the boot If you forget the password, you may have to discharge the battery of the CMOS. Contact your
password. service representative for help.


Password Warning
If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot
remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.

The sound cannot be The volume might be set too low. Check the volume control in the Volume Control Panel in the
heard or the volume is Windows taskbar, or use the key combination Fn + F5 and F6 (see “Audio Features” on page 2
very low. - 10/“Audio Features” on page D - 6) to adjust. 8
The audio recording The compact disc is dirty. Clean it with a CD-ROM cleaner kit.
cannot be heard or the
volume is very low.

Audio cannot be heard The Recording Line-In jack allows you to record audio sources to the computer. Note that the
through the recording audio will not play through the computer’s speakers. You will need to listen to the audio
line-in jack. source on the original device, or split the audio signal through the notebook computer and
another device.

Problems and Possible Solutions 8 - 9


Troubleshooting

Problem Possible Cause - Solution

The CD/DVD cannot be The compact disc is not correctly placed in the tray. Gently try to remove the disc using the eject
read. hole (see “Loading Discs” on page 2 - 3).

The DVD regional The code has been changed the maximum 5 times. See “DVD Regional Codes” on page 2 - 5/
codes can no longer be “DVD Regional Codes” on page D - 2.
changed.

Unwelcome numbers If the LED is lit, then Num Lock is turned ON. (see “LED Indicators” on page 1 - 9).
appear when typing.


Other Keyboards
8 If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will
detect and enable it automatically. However special functions/hot keys unique to the system’s regular keyboard may not
work.

The system freezes or The system’s power saving features have timed-out. Use the AC/DC adapter, press the sleep (Fn
the screen goes dark. + F4) key combination, or press the power button if no LEDs are lit.

The system never goes Power Options features are not enabled. Go to the Windows Power Options menu and enable
into a power saving the features you prefer (see “System Power Options” on page 3 - 6/“System Power Options”
mode. on page D - 20). Make sure you have enabled Hibernate mode from the control panel.

8 - 10 Problems and Possible Solutions


Troubleshooting

Problem Possible Cause - Solution

The Wireless LAN/ The modules are off. Check the LED indicator to see if the WLAN/Bluetooth module is on or
Bluetooth modules off (see “LED Indicators” on page 1 - 9). If the LED indicator is off, then press the Fn + F11
cannot be detected. (WLAN) or Fn + F12 (Bluetooth) key combination(s) in order to enable the modules (see
“Function Keys” on page 1 - 11).

The PC Camera module The module is off. Press the Fn + F10 key combination in order to enable the module (see
cannot be detected. “Function Keys” on page 1 - 11). Run the BisonCap program (see “Bluetooth Local Area
Connection” on page 7 - 9/“PC Camera Module” on page D - 39) to view the camera picture.

The Wireless LAN/ The driver(s) for the module(s) have not been installed. Make sure you have installed the driver
Bluetooth/ PC Camera for the appropriate module (see the instructions for the appropriate module in “Modules &
modules cannot be Options” on page 7 - 1/“What to Install” on page D - 28).
configured.

The computer stops The computer may stop responding when you put it into (or resume from) Stand By or Hibernate,
responding during or when you shut down. This error is caused by power management within Windows XP, when 8
stand by or hibernation applied to a PC Camera attached to the internal USB hub.
operations, or when you
try to use the Shut Down Microsoft has posted a Hotfix for this error on its website (search for Hotfix KB909667). Download
command. and install the Hotfix to correct this error.

Problems and Possible Solutions 8 - 11


Troubleshooting

Non DDC CRT Monitors (for Win Vista Only)


If you are experiencing screen flicker problems (in Windows Vista ONLY) when using an older CRT (Non
DDC) as your external display, you can install an updated driver to fix this problem. Follow the steps below:

Uninstall the Original Driver


1. Detach any connected external CRT.
2. Go to the Control Panel in the Windows OS and double-click the Programs and Features icon (Programs >
Uninstall a program).
3. Click to select the VIA Display Vista Driver *****, and then click Uninstall and follow the on screen prompts.
4. Click Yes to restart the computer.

Install the Updated Driver


1. Insert the Device Drivers & Utilities + User’s Manual CD-ROM.
8 2. Click Browse CD (button).
3. Navigate (Browse...) to X:\Drivers\Video_NonDDC\ and double-click setup.exe.
4. Click Next > Next.
5. Click Finish to restart the computer.
6. Reattach the external CRT and configure as outlined in “Attaching Other Displays” on page B - 4.

8 - 12 Non DDC CRT Monitors (for Win Vista Only)


Interface (Ports & Jacks)

Appendix A: Interface (Ports & Jacks)


Overview
The following chapter will give a quick description of the interface (ports & jacks) which allow your computer
to communicate with external devices, connect to the internet etc.

Interface (Ports & Jacks) A - 1


Interface (Ports & Jacks)

Notebook Ports and Jacks


Item Description

Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the
slot and it will appear as a removable device.

DC-In Jack Plug the supplied AC/DC adapter into this jack to power your computer.

External Monitor (VGA) This port allows you to connect an external monitor, or Flat Panel Display, to get dual video or
Port simultaneous display on the LCD and external monitor/FPD.

Headphone-Out Jack Headphones or speakers may be connected through this jack. Note: Set your system’s volume to
a reduced level before connecting to this jack.
A
Recording Line-In Jack The Recording Line-In jack allows you to record audio sources to the computer. Note that the
audio will not play through the computer’s speakers. You will need to listen to the audio
source on the original device, or split the audio signal through the notebook computer and
another device.

Microphone-In Jack Plug an external microphone in to this jack to record on your computer.

A - 2 Interface (Ports & Jacks)


Interface (Ports & Jacks)

Item Description

RJ-11 Modem Jack This port connects to the built-in modem. You may plug the telephone line directly into this RJ-11
telephone connection.

RJ-45 LAN Jack This port supports LAN (Network) functions.


Note: Broadband (e.g. ADSL) modems usually connect to the LAN port.

Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be
purchased at any computer store.

S/PDIF-Out Jack This S/PDIF (Sony/Philips Digital Interface Format) Out Jack allows you to connect your DVD-
capable PC to a Dolby AC-3 compatible receiver for “5.1” or ‘dts’ surround sound.

USB 2.0/1.1 Ports These USB 2.0 compatible ports (USB 2.0 is fully USB 1.1 compliant) are for low-speed
peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as
external HDDs, digital video cameras or high-speed scanners etc. Devices can be plugged into A
the computer, and unplugged from the computer, without the need to turn the system off (if the
power rating of your USB device is 500mA or above, make sure you use the power supply which
comes with the device).

Interface (Ports & Jacks) A - 3


Interface (Ports & Jacks)

A - 4
Video Driver Controls

Appendix B: Video Driver Controls


VIA Video Driver Installation
Make sure you install all the drivers in the order indicated in Table 4 - 1, on page 4
- 3. Instructions for installing the video driver are repeated below.

Video
1. Click 1.Install Video Driver > Yes.
2. Click Next > Next.
3. Click Finish to restart the computer.

VIA Video Driver Installation B - 1


Video Driver Controls

Advanced Video Controls



This section is about making adjustments for the LCD, and switching display devic-
Function Key
Combination
es. The basic settings for configuring the LCD are outlined in “Video Features” on
page 1 - 17.
You can use the Fn +
F7 key combination to
toggle through the dis-
Video Driver Controls
play options: The video interface lets you change the screen resolution and color output to what-
ever is most comfortable/efficient for you. This is a matter of hardware, video mem-
• Notebook Only
ory and the driver for your operating system.
• External Display
Only
• Notebook + External Video Memory
Display The system does not feature dedicated video memory, but automatically and dynam-
Make sure you give the ically allocates as much (up to 256MB maximum) system memory (RAM) as need-
displays enough time
to refresh.
ed to the video system. You can define the amount of system memory to be allocated
from the BIOS (see “Frame Buffer Size: (Advanced Menu)” on page 5 - 9). The
system returns whatever memory is no longer needed to the operating system.
B

B - 2 Advanced Video Controls


Video Driver Controls

VIA S3Tray Plus Utility


The S3Tray Plus utility will appear in the taskbar when the video driver is installed.
Click/Right-click the icon to bring up the menu below. From this menu you will
also be able to make display adjustments, access the Display Properties control pan-
el, check video memory information etc.

Figure B - 1
Right-Click Icon
S3Tray Plus
Taskbar Utility
Click Icon

Advanced Video Controls B - 3


Video Driver Controls

Attaching Other Displays


 Besides the built-in LCD, you can also use an external monitor (CRT)/flat panel dis-
Non DDC CRT play as your display device. Connect it to the external monitor port at the rear of the
Monitors (for Win computer, and follow the instructions below:
Vista Only)
Windows Vista
If you are experiencing
screen flicker problems 1. Attach your external display to the external monitor port and turn it on.
(in Windows Vista 2. If a New Display Detected window does not appear in Windows Vista, go to the
ONLY) when using an Windows Mobility Center control panel (Mobile PC > Adjust commonly used
older CRT (Non DDC) mobility settings) and click Connect display.
as your external display, 3. Click on any of the buttons to configure the displays to your preferences, or click
you can install an updat- Display Settings (in the New Display Detected window) to access the control
ed driver to fix this prob- panel.
lem (see “Non DDC
CRT Monitors (for Win
Vista Only)” on page 8
- 12).

B
Figure B - 2
New Display
Detected

B - 4 Attaching Other Displays


Video Driver Controls

External displays may also be configured from S3Display tab in Advanced Display
Settings: 
1. Attach the external display to the external monitor port and turn it on. S3Tray Plus Utility
2. Click Advanced Settings in the Display Settings control panel (see “Video
Features” on page 1 - 17) to display the additional tabs. You can also use the
3. Select S3Display (tab). S3Tray Plus utility in
4. Click to put a tick in the tickbox under the CRT icon. the taskbar to configure
5. Click Apply > OK and allow the monitor time to refresh the display. an external display.
6. Click Yes to confirm the settings.
Attach the external dis-
7. Select the CRT icon, and then click Refresh Rate to change the settings for the play (CRT) to the exter-
attached display. nal monitor port.

Right-click the icon


in the taskbar and select
S3Display.

Select the CRT (it


should have a tick
alongside it) and click
Yes to confirm the set-
tings. B

Figure B - 3
S 3Display

Attaching Other Displays B - 5


Video Driver Controls

Display Modes
Single Display
Only one of your attached displays is used.

Mirrored
This display mode simply shows an exact copy of the Primary display desktop on
the Secondary display(s).

Extended Desktop
An Extended desktop allows the desktop to span the displays to act as a large work
area, thus creating a lot more screen area for display. Each display device can be con-
figured independently for specific resolutions and refresh rates. Use the Display Set-
tings control panel to drag the monitors to match the physical arrangement you wish
to use.

B - 6 Display Modes
Video Driver Controls

Using Windows Vista to Enable Extended Mode


1. Attach your external display to the external monitor port, and turn it on. 
2. If a New Display Detected window does not appear in Windows Vista, go to the
Windows Mobility Center control panel (Mobile PC > Adjust commonly used Display Settings
mobility settings) and click Connect display. Extended Desktop
3. Click to select Show different parts of my desktop on each display (extended). Use the control panel to
4. Click Right or Left under Extend your desktop. drag the monitors to
5. Click Apply > OK. match the physical ar-
rangement you wish to
use.

You can drag any icons


or windows across to ei-
ther display desktop,
which makes it possible
to have one program
visible in one of the dis-
plays, and a different
program visible in the
other display.

B
Figure B - 4
Display Properties
(Extended Desktop)

Display Modes B - 7
Video Driver Controls

Using Display Settings to Enable Extended Mode


1. Attach your external display to the external monitor port, and turn it on.
2. Open the Display Settings control panel (see “Video Features” on page 1 - 17).
3. Click the monitor icon (e.g. 2 ), and make sure you have checked “Extend the
desktop onto this monitor.” and click Apply.
Click the appropriate monitor icon
(e.g. 2 ) to be able to select the op-
tion to extend the desktop on to it.

Figure B - 5 In this example the Primary Display


Display Properties 1 is on the left, the Secondary Dis-
(Extended Desktop) play 2 is on the right.

B - 8 Display Modes
Specifications

Appendix C: Specifications

Latest Specification Information
The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/
speeds and CD/DVD device types) may be changed or updated due to the manufacturer's release schedule. Check with your
service center for details.

Specifications C - 1
Specifications

Feature Specification
Processor Intel® Core™2 Duo Processor 65nm (65 Nanometer) Process Technology
(478-pin) Micro-FC-PGA Package 4MB On-die L2 Cache & 667MHz FSB
T7200/ T7400/ T7600 2.0/ 2.16/ 2.33 GHz

Intel® Core™2 Duo Processor 65nm (65 Nanometer) Process Technology


(478-pin) Micro-FC-PGA Package 2MB On-die L2 Cache & 667MHz FSB
T5500/ T5600 1.66/ 1.83 GHz

Intel® Celeron® M Processor 65nm (65 Nanometer) Process Technology


(478-pin) Micro-FCPGA Package 1MB On-die L2 Cache & 533MHz FSB
410/ 420/ 430/ 440/ 450 1.46/ 1.60/ 1.73/ 1.86/ 2.0 GHz

Core Logic VIA VN896 + VT8237A Chipset

Memory Model A Computers: Model B Computers:

Two 200 Pin SO-DIMM Sockets Supporting DDRII One 200 Pin SO-DIMM Socket Supporting DDRII
(DDR2) 533/667 MHz (DDR2) 533/667 MHz
64-bit Wide DDRII (DDR2) Data Channel 64-bit Wide DDRII (DDR2) Data Channel
Memory Expandable up to 2GB (256/ 512/ 1024 Memory Expandable up to 1GB (256/ 512/ 1024
MB DDRII Module) MB DDRII Module)

(Note: Do Not Use Other Module Types) (Note: Do Not Use Other Module Types)
C
Security Security (Kensington® Type) Lock Slot BIOS Password

BIOS One 4Mb Flash ROM Phoenix™ BIOS

C - 2 Specifications
Specifications

Feature Specification
LCD Model A Computers: Model B Computers:

15.0" XGA (1024*768) Flat Panel TFT 14.1" WXGA (1280*768) Flat Panel TFT
OR OR
15.0" XGA (1024*768) Glare Type Flat Panel TFT 14.1" WXGA (1280*768) Glare Type Flat Panel TFT

Video Adapter VIA VN896 Integrated Video System


Chrome9 HC™ Pro 2D/3D Graphics
Integrated 128bit 2D/3D Graphic Engine and Clock up to 250MHz
Supports CRT Resolutions up to 2048 * 1536 at 75Hz
Supports Microsoft DirectX 9.0

Storage One Changeable 12.7mm(h) Optical Device (CD/DVD) Type Drive (see “Optional” on page C - 5 for
drive options)
Easy Changeable 2.5" 9.5 mm (h) SATA (Serial) HDD

Audio Integrated Azalia Compliant Interface 2 * Built-In Speakers


3D Stereo Enhanced Sound System Built-In Microphone
Sound-Blaster PRO™ Compatible

Keyboard & Winkey Keyboard Built-In TouchPad with Scrolling Function


Pointing Device

Specifications C - 3
Specifications

Feature Specification
Interface Three USB 2.0 Ports One S/PDIF Output Jack
One External Monitor Port One RJ-11 Modem Jack
One Headphone-Out Jack One RJ-45 LAN Jack
One Microphone-In Jack One DC-in Jack
One Recording Line-In Jack

Card Reader Embedded 7-in-1 Card Reader (MS/ MS Pro/ SD/ Mini SD/ MMC/ RS MMC/ MS Duo)
Note: MS Duo/ Mini SD/ RS MMC Cards require a PC adapter

ExpressCard Slot One ExpressCard/34/54 Slot

Communication 56K Plug & Play Fax/Modem v90/92 Compliant


10M/1000/M Base-TX Ethernet (Gigabit)
(Factory Option) 300K or 1.3M (UVC or non UVC) Pixel PC Camera with USB Interface
(Factory Option) Bluetooth Module - Version 2.0
(Option) 802.11b/g Wireless LAN Module with USB Interface

Power Supports ACPI 2.0 Supports Battery Low Suspend


Management Supports Suspend to RAM (S3) Supports Resume from Modem Ring
Supports Suspend to Disk (S4) Supports Wake on LAN
Supports Soft Off (S5)

Power Full Range AC/DC Adapter 19V, 3.42A or 18.5V, 3.5A (65 Watts), 100 - 240V, 50 - 60Hz
C
6 Cell Smart Lithium-Ion Battery Pack, 4000mAH (44.4W)

C - 4 Specifications
Specifications

Feature Specification
Environmental Temperature Relative Humidity
Spec Operating: 5°C ~ 35°C Operating: 20% ~ 80%
Non-Operating: -20°C ~ 60°C Non-Operating: 10% ~ 90%

Physical Model A Computers: Model B Computers:


Dimensions & 333mm (w) * 276mm (d) * 24-33mm (h) 333mm (w) * 243mm (d) * 24-33mm (h)
Weight 2.5 kg With 6 Cell Battery 2.2 kg With 6 Cell Battery

Optional Optical Drive Module Options: 802.11b/g Wireless LAN Module with USB
DVD/CD-RW Combo Drive Module Interface
DVD Super-Multi Drive Module
(Factory Option) PC Camera with USB Interface

(Factory Option) Bluetooth Module - Version 2.0

Specifications C - 5
Specifications

C - 6
Windows XP Information

Appendix D: Windows XP Information


This Appendix contains information (including control panel information, driver installation etc.) for users of
the Windows XP OS.

D - 1
Windows XP Information

DVD Regional Codes



Changing DVD Regional Codes
Go to the Control Panel and double-click System > Hardware (tab), click Device Manager, then click the + next to DVD/CD-ROM drives.
Double-click on the DVD-ROM device to bring up the Properties dialogue box, and select the DVD Region (tab) to bring up the control
panel to allow you to adjust the regional code.

DVD region detection is device dependent, not OS-dependent. You can select your module’s region code 5 times. The fifth selection is
permanent. This cannot be altered even if you change your operating system or you use the module in another computer.

Region Geographical Location

1 USA, Canada

2 Western Europe, Japan, South Africa, Middle East & Egypt

3 South-East Asia, Taiwan, South Korea, The Philippines, Indonesia, Hong Kong

South & Central America, Mexico, Australia,


4
New Zealand

5 N Korea, Russia, Eastern Europe, India & Most of Africa

6 China

D Table D - 1 - DVD Region Codes Figure D - 1 - DVD Regions

D - 2 DVD Regional Codes


Windows XP Information

Windows XP Start Menu & Control Panel


Most of the control panels, utilities and programs within Windows XP (and most other Windows versions) are
accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk
drive, and a shortcut will usually be placed in the Start menu and/or the desktop. You can customize the look of
the Start menu by right-clicking the Start menu and selecting Properties from the menu.

Click here to toggle Category View

Figure D - 2 - Start Menu & Control Panel


In many instances throughout this manual you will see an instruction to open the Control Panel. The Control
Panel is accessed from the Start menu, and it allows you to configure the settings for most of the key features
in Windows (e.g. power, video, network, audio etc.). Windows XP provides basic controls for many of the fea-
tures, however many new controls are added (or existing ones are enhanced) when you install the drivers listed D
in Table D - 2, on page D - 27. To see all controls it may be necessary to toggle off Category View.

Windows XP Start Menu & Control Panel D - 3


Windows XP Information

Application Hot Key


 The hot key buttons give instant access to the default Internet browser and e-mail
Application.exe program, and to a user-defined application, with one quick button press. To configure
You will need to locate a program to open when the application hot key is pressed (Windows Media
the actual application Player is the default program), follow the instructions below.
executable (.exe) file,
not just the shortcut. To 1. Right click the Hot Key driver icon in the taskbar.
find the application right- 2. Select Setup from the menu, scroll to Application 1 and press Enter.
click its shortcut on the 3.
desktop and click Prop-
erties. Click the short-
cut (tab) and see where
the executable file is lo-
cated by clicking the 4.
Find Target (button). 5. An Open dialog box will appear on the screen.

Figure D - 3
Application Hot Key
Configuration

6. Browse to the directory where the desired application.exe (see the sidebar)
D program exists.
7. Double-Click on the program file or choose Open.

D - 4 Application Hot Key


Windows XP Information

TouchPad and Buttons/Mouse



The TouchPad is an alternative to the mouse; however, you can also add a mouse to
your computer through one of the USB ports. The TouchPad buttons function in much Mouse Driver
the same way as a two-button mouse. If you are using an ex-
ternal mouse your op-
Install the TouchPad driver (see “TouchPad (WinXP)” on page D - 32) and then dou- erating system may be
able to auto-configure
ble-click the TouchPad icon on the taskbar to configure the functions (tapping, your mouse during its
buttons, scrolling, pointer motion and sensitivity) to your preferences. Further infor- installation or only en-
mation is available at www.synaptics.com. able its basic functions.
Be sure to check the
device’s user docu-
mentation for details.

Figure D - 4
Mouse Properties

TouchPad and Buttons/Mouse D - 5


Windows XP Information

Audio Features
 You can configure the audio options on your computer from the Sounds and Audio
Sound Volume Devices Windows control panel, or from the VIA Audio Deck icon in the
Adjustment taskbar, or on the desktop (this will bring up the VIA Audio Deck menu). The vol-
How high the sound vol- ume may also be adjusted by means of the Fn + F5/F6 key combination.
ume can be set depends
on the setting of the vol-
ume control within Win-
dows (and the volume
control function keys on
the computer). Click the
Volume icon on the
taskbar to check the set-
ting.
Microphone
Boost

Figure D - 5
VIA Audio Deck
Configuration
D Menus

D - 6 Audio Features
Windows XP Information

Video Features
You can switch display devices, and configure display options, from the Display Properties control panel in
Windows as long as the video driver is installed. For further information see either “VIA Video Driver Con-
trols” on page D - 9 (from pages D - 9 to D - 13).

1. Click Start, point to Settings and click Control Panel (or click Control
Panel).
2. Double-click Display (icon); Display (icon) is in the Appearances and
Themes category.
3. Click Settings (tab) in the Display Properties dialog box.
4. Move the slider to the preferred setting in Screen resolution 1 .
5. Click the arrow, and scroll to the preferred setting in Color quality 2 .
6. Open the Display Properties control panel, and click Advanced (button)
3 to bring up the Advanced properties tabs.
2 7. The Advanced properties tabs include specific VIA controls, which allow
1 you to make any video adjustments you require.

Figure D - 6 - Display Properties

Video Features D - 7
Windows XP Information

Advanced Video Controls



This section is about making adjustments for the LCD, and switching display devic-
Function Key
Combination
es.

You can use the Fn + Video Driver Controls


F7 key combination to
toggle through the dis- The video interface lets you change the screen resolution and color output to what-
play options: ever is most comfortable/efficient for you. This is a matter of hardware, video mem-
ory and the driver for your operating system.
• Notebook Only
• External Display
Only Video Memory
• Notebook + External The system does not feature dedicated video memory, but automatically and dynam-
Display ically allocates as much (up to 256MB maximum) system memory (RAM) as needed
Make sure you give the to the video system. You can define the amount of system memory to be allocated
displays enough time
to refresh.
from the BIOS (see “Frame Buffer Size: (Advanced Menu)” on page 5 - 9). The
system returns whatever memory is no longer needed to the operating system.

D - 8 Advanced Video Controls


Windows XP Information

VIA Video Driver Controls


VIA S3Tray Plus Utility
The S3Tray Plus utility will appear in the taskbar when the video driver is installed.
Click/Right-click the icon to bring up the menu below. From this menu you will
also be able to make display adjustments, access the Display Properties control panel,
check video memory information etc.
Figure D - 7
S3Tray Plus Taskbar
Utility

Right-Click
Click Icon Icon

VIA Video Driver Controls D - 9


Windows XP Information

VIA S3 Display Control Panels


 Right-click the S3Tray Plus utility in the taskbar to bring up the menu for the
Help Menus individual control panels, or access the menus from the Advanced tab in the Display
Properties control panel.
Right-click on almost
any item in the tabs to
bring up the “What’s
This?” button.

Click the “What’s


This?” button to bring
up a help menu (if the
item has a help menu
associated with it).

Help Menu

Figure D - 8
S3 Control Panels

D - 10 VIA Video Driver Controls


Windows XP Information

Display Devices (VIA)



Besides the built-in LCD, you can also use an external monitor (CRT)/flat panel dis-
S3Tray Plus Utility
play as your display device. Connect it to the external monitor port on the right of the
computer. See the instructions below: You can also use the
S3Tray Plus utility in
the taskbar to config-
ure an external dis-
play.

Attach the external dis-


play (CRT) to the ex-
ternal monitor port.

Right-click the
icon in the taskbar and
select S3Display.

Select the CRT (it


should have a tick
alongside it) and click
1. Attach the external display to the external monitor port and turn it on. Yes to confirm the set-
2. Click Advanced in the Display Properties control panel (see “Video Features” on tings.
page D - 7) to display the additional tabs.
3. Select S 3Display (tab).
4. Click to put a tick in the tickbox under the CRT icon. Figure D - 9
5. Click Apply > OK and allow the monitor time to refresh the display. S 3Display D
6. Click Yes to confirm the settings.

Display Devices (VIA) D - 11


Windows XP Information

Display Modes (VIA)



Single Display
Playing DVD Videos
Only one of your attached displays is used.
If you want to play a
DVD video in a multiple Multiple Monitors
monitor mode, then
choose EITHER the This display mode simply shows an exact copy of the Primary display desktop on
notebook LCD OR ex- the Secondary display(s).
ternal display as the dis-
play device. It is not Extended Desktop
possible to play a DVD
video simultaneously on
An Extended desktop allows the desktop to span the displays to act as a large work
both displays. area, thus creating a lot more screen area for display. Each display device can be con-
figured independently for specific resolutions and refresh rates. Use the Display
Properties control panel to drag the monitors to match the physical arrangement you
wish to use.

D - 12 Display Modes (VIA)


Windows XP Information

To Enable Extended Desktop (Display Properties)


1. Attach the external display to the external monitor port and turn it on. 
2. Go to the Display Properties control panel (see “Video Features” on page D - 7)
Display Settings
and click Settings (tab).
Extended Desktop
3. Click the monitor icon (e.g. 2 ), and click to put a tick in the “Extend my Windows
desktop onto this monitor.” box, and then click Apply. Use the control panel
4. As long as the appropriate monitor icon is selected you can adjust the screen to drag the monitors to
resolution, color quality etc. match the physical ar-
5. Click Apply > Yes to confirm any setting changes rangement you wish to
use.
Click the appropriate monitor
You can drag any
icon (e.g. 2 ) to be able to select icons or windows
the option to extend the desktop across to either display
on to it. desktop, which makes
it possible to have one
program visible in one
In this example the Primary mon- of the displays, and a
itor 1 is on the left, the secondary different program visi-
display 2 is on the right. ble in the other display.

Figure D - 10
Display Properties
(Extended
Desktop) D

Display Modes (VIA) D - 13


Windows XP Information

Power Management Features


The Power Options control panel icon in Windows (see page D - 3) allows you to configure power management
features for your computer. You may conserve power through individual components such as the monitor or hard
disk (by means of Power Schemes), or you may use either Stand by or Hibernate mode to conserve power
throughout the system (enable Hibernate support from the control panel tab). Pay attention to the instructions
on battery care in “Battery Information” on page D - 23.

Figure D - 11 - Power Options


The computer’s power button, sleep button (Fn + F4 key combination), and lid (closing the lid) may be set to
send the computer in to either Stand by or Hibernate mode.

D Power Saving and Performance


Power Schemes may have an affect on your computer performance (see “Power Schemes” on page D - 18).

D - 14 Power Management Features


Windows XP Information

Overview

To conserve power, especially when using the battery, your computer uses the ACPI
power management system. Power management conserves power by controlling in- OS Note
dividual components of the computer (the monitor and hard disk drive) or the whole Power management
system. This chapter covers: functions will vary
slightly depending on
• The Power Sources your operating system.
• Turning on the Computer For more information it
is best to refer to the
• Power Schemes user’s manual of your
• System Power Options operating system.
• Configuring the Power Button
• Battery Information (Note: All pictures
used on the following
pages are from the
Advanced Configuration and Power Interface Windows XP OS.)
The ACPI interface provides the computer with enhanced power saving techniques
and gives the operating system (OS) direct control over the power and thermal states
of devices and processors. For example, it enables the OS to set devices into low-
power states based on user settings and information from applications. ACPI is fully
supported in Windows XP.

Overview D - 15
Windows XP Information

The Power Sources


The computer can be powered by either an AC/DC adapter or a battery pack.

AC/DC Adapter
Use only the AC/DC adapter that comes with your computer. The wrong type of AC/DC adapter will damage
the computer and its components.
1. Attach the AC/DC adapter to the DC-in jack on the right of the computer.
2. Plug the AC power cord into an outlet, and then connect the AC power cord to the AC/DC adapter.
3. Raise the lid/LCD to a comfortable viewing angle.
4. Press the power button to turn “On”.

Battery
The battery allows you to use your computer while you are on the road or when an electrical outlet is unavailable.
Battery life varies depending on the applications and the configuration you're using. To increase battery life,
let the battery discharge completely before recharging (see “How do I completely discharge the battery?”
on page D - 26).

We recommend that you do not remove the battery. For more information on the battery, please refer to “Battery
Information” on page D - 23.

D - 16 The Power Sources


Windows XP Information

Turning on the Computer


Now you are ready to begin using your computer. To turn it on simply press the pow-

er button on the front panel. Shutdown
Note that you should al-
When the computer is on, you can use the power button as a Stand by/Hibernate/ ways shut your comput-
Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and er down by choosing the
holding the power button for longer than this will shut the computer down). Use Turn Off Computer
command from the Start
Power Options in the Windows control panel to configure this feature. menu in Windows. This
will help prevent hard
disk or system prob-
lems.

Forced Off
If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the pow-
er button for 4 seconds, or longer, to force the system to turn itself off.

Power Button as Stand by or Hibernate Button


If you are using a fully ACPI-compliant OS, (such as Windows XP) you can use the OS’s
“Power Options” control panel to set the power button to send the system into Stand by or
Hibernate mode (see your OS’s documentation, or “Configuring the Power Button” on
page D - 22 for details).

Turning on the Computer D - 17


Windows XP Information

Power Schemes
 You can set your computer to conserve power through individual components by
Resuming means of Power Schemes. You can also adjust the settings for each scheme to set
Operation the monitor to turn off after a specified time, and the computer's hard disk motor to
Press a key on the key- turn off if the hard disk drive has not been accessed for a specified period of time (if
board, or move the the system reads or writes data, the hard disk motor will be turned back on). The
mouse/TouchPad to re- schemes may also be set to set a specified time for the system to enter Stand by or
sume from Monitor or
Hard Disk Stand by.
Hibernate modes (see “System Power Options” on page D - 20).

Figure D - 12
Power Schemes

D - 18 Power Schemes
Windows XP Information

Each Windows Power Scheme will also adjust the processor performance of your machine in order to save pow-
er. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery
power).

Choose the Home/Office Desk scheme for maximum performance when the computer is powered from an AC
power source. Choose the Max Battery scheme (bear in mind that this scheme may slow down the overall per-
formance of the computer in order to save power) for maximum power saving when the computer is battery (DC
power) powered. Windows will use Portable/Laptop as the default scheme.

Power Schemes D - 19
Windows XP Information

System Power Options


You can use the system power options to stop the computer’s operation and restart where you left off. This sys-
tem features Stand by and Hibernate sleep mode levels (Hibernate mode will need to be enabled by clicking
the option in the Hibernate tab in the Power Options control panel - see “Hibernate” on page D - 21).

Hibernate Mode vs. Shutdown


Hibernate mode and Shutdown are the same in that the system is off and you need to press the power button to
turn it on. Their main difference is:
When you come back from hibernation, you can return to where you last left off (what was on your desktop)
without reopening the application(s) and file(s) you last used.
You can use either method depending on your needs.

Stand by Mode vs. Hibernate Mode


If you want to stay away from your work for just a while, you can put the system on Stand by instead of in hi-
bernation. It takes a longer time to wake up the system from Hibernate mode than from Stand by mode.

D - 20 System Power Options


Windows XP Information

Stand by
Stand by saves the least amount of power, but takes the shortest time to return to full 
operation. During Stand by the hard disk is turned off, and the CPU is made to idle System Resume
at its slowest speed. All open applications are retained in memory. When you are not
using your computer for a certain length of time, which you specify in the operating The system can resume
from Stand by mode by:
system, it will enter Stand by mode to save power.
• Pressing the power
Hibernate button
Hibernate uses no power and saves all of your information on a part of the HDD be- • Pressing the Sleep/
fore it turns the system off. Although it saves the most power it takes the longest time Resume key combina-
to return to full operation. You can set your computer to automatically enter Hiber- tion (Fn + F4).
nate mode when the battery power is almost depleted. You will need to enable Hi- • Network card activity
bernate mode from the Hibernate tab in the Power Options control panel. The (Wake on LAN if
system will resume from Hibernate mode by pressing the power button. enabled)

Figure D - 13
Enable Hibernation

System Power Options D - 21


Windows XP Information

Configuring the Power Button


 The power button may be set to send the computer in to either Stand by or Hiber-
Sleep Button nate mode. In Stand by mode, the LED will blink green. In Hibernate mode
You may also configure the LED will be off (battery) or orange (AC/DC adapter). If you are in a power saving
the Sleep/Resume key mode set to save power through individual components (e.g. hard disk, monitor), the
combination (Fn + F4) LED will remain green.
from the menu illustrat-
ed in Figure D - D - 14.
In Windows this is re-
ferred to as the Sleep
button.

Figure D - 14
Power Options
(Advanced - Power
Buttons)

Power Button Lid Sleep/Resume


(Sleep) Button

D - 22 Configuring the Power Button


Windows XP Information

Battery Information
Please follow these simple guidelines to get the best use out of your battery.

Low Battery
New Battery Warning
Always completely discharge, then fully charge, a new battery (see “Battery FAQ” When the battery is criti-
on page D - 26 for instructions on how to do this). cally low, immediately
connect the AC/DC
Battery Life adapter to the computer
Your computer’s battery life is dependent upon many factors, including the programs or save your work, oth-
erwise, the unsaved
you are running, and peripheral devices attached. Power Options (you may set low data will be lost when
battery Alarms and actions, and check the Power Meter from the Power Options the power is depleted.
control panel), and settings in the OS will help prolong the battery life if configured
appropriately.

Figure D - 15
Power Options
(Alarm & Power
Meter)

Battery Information D - 23
Windows XP Information

Battery life may be shortened through improper maintenance. To optimize the life
 and improve its performance, fully discharge and recharge the battery at least
once every 30 days.
Conserving
Battery Power We recommend that you do not remove the battery yourself. If you do need to re-
To conserve battery power: move the battery for any reason see “Removing the Battery” on page 6 - 3.
Lower the brightness level
of the LCD display. The Recharging the Battery with the AC/DC Adapter
system will decrease LCD The battery pack automatically recharges when the AC/DC adapter is attached and
brightness slightly to save
power when it is not pow- plugged into an electrical outlet. If the computer is powered on, and in use, it will
ered by the AC/DC adapt- take several hours to fully recharge the battery. When the computer is turned off but
er.
plugged into an electrical outlet, battery charge time is less. (Refer to “LED Indica-
Close modem or communi- tors” on page 1 - 9 for information on the battery charge status, and to “Battery In-
cation applications when formation” on page D - 23 for more information on how to maintain and properly
they are not being used.
recharge the battery pack.)
Remove any unused Ex-
press Cards from the com-
puter (Express Cards
quickly use up battery pow-
er even if the system enters
sleep mode).

Disconnect any unneces-


sary external devices.

D - 24 Battery Information
Windows XP Information

Proper handling of the Battery Pack


• DO NOT disassemble the battery pack under any circumstances
• DO NOT expose the battery to fire or high temperatures, it may explode
• DO NOT connect the metal terminals (+, -) to each other


Damaged Battery Warning
Should you notice any physical defects (e.g. the battery is bent out of shape after being
dropped), or any unusual smells emanating from the notebook battery, shut your computer
down immediately and contact your service center. If the battery has been dropped we do
not recommend using it any further, as even if the computer continues to work with a dam-
aged battery in place, it may cause circuit damage, which may possibly result in fire. It is
recommended that you replace your computer battery every two years.

Battery Information D - 25
Windows XP Information

Battery FAQ
 How do I completely discharge the battery?
Caution Use the computer with battery power until it shuts down due to a low battery. Don’t
turn off the computer by yourself even when you see a message that indicates the bat-
Danger of explosion if tery is critically low, just let the computer use up all of the battery power and shut
battery is incorrectly re-
placed. down on its own. Disable the Power Options functions in the Control Panel, espe-
cially any Alarms (unclick the tickboxes - see page D - 23) and Schemes (change
Replace only with the all the settings to Never - see page D - 18). As the battery nears the end of its life save
same or equivalent type and close any critical files.
recommended by the
manufacturer. Discard
used battery according How do I fully charge the battery?
to the manufacturer’s in- When charging the battery, don’t stop until the LED charging indicator light changes
structions. from orange to green.

How do I maintain the battery?


Completely discharge and charge the battery at least once every 30 days or after
about 20 partial discharges.

D - 26 Battery Information
Windows XP Information

Driver Installation WinXP SP2 Driver Page #


The Device Drivers & Utilities + User’s Manual CD-
Install the appropriate WinXP Service Pack Page D - 29
ROM contains the drivers and utilities necessary for
the proper operation of the computer. Table D - 2 lists Chipset Page D - 30
what you need to install, and it is very important that Video Page D - 31
the drivers are installed in the order indicated.
Modem Page D - 31

Only install drivers for modules (WLAN, Bluetooth, Audio Page D - 31

and PC Camera) included in your purchase option. LAN Page D - 31

TouchPad Page D - 32
Installation Methods (Win XP)
CardReader Page D - 32
You may choose to install the drivers from the autorun
program, or install them manually. Hot Key Page D - 32

Wireless LAN Page D - 33

Bluetooth Page D - 35

PC Camera Page D - 40

Table D - 2 - Driver Installation

Driver Installation D - 27
Windows XP Information

What to Install 1. Check the driver installation order from Table D - 2,


on page D - 27 (all the drivers must be installed
Insert the Device Drivers & Utilities + User’s Manual in this order) which is the same as that listed in the
CD-ROM (WinXP) and click Install WinXP Drivers Drivers Installer menu below.
(button), or Install Option Drivers (button) to access 2. Click to select the driver you wish to install, after
the Optional driver menu. installing each driver it will become grayed out (if
you need to reinstall any driver, click the Unlock
button).
3. Follow the instructions for each individual driver
installation procedure as listed on the following
pages.

Figure D - 16 - Drivers Installer Screen 1


D
Figure D - 17 - Drivers Installer Screen 2

D - 28 What to Install
Windows XP Information

Updating/Reinstalling Individual Drivers


If you wish to update/reinstall individual drivers it 
may be necessary to uninstall the original driver.To do
this go to the Control Panel in the Windows OS and Windows XP Service Pack 2
double-click the Add/Remove Programs item. If you Make sure you install Windows XP Service Pack 2 (or
see the individual driver listed (if not see below), un- a Windows XP version which includes Service Pack 2)
before installing any drivers. Service Pack 2 includes
install it, following the on screen prompts (it may be support for USB 2.0.
necessary to restart the computer). Go to the appropri-
If you have upgraded the system by installing Service
ate section of the manual to complete the update/rein- Pack 2 (i.e. your Windows XP version does not include
stall procedure for the driver in question. Service Pack 2) then follow these instructions:
1.Click Start (menu), point to Settings and click Control
If the driver is not listed in the Add/Remove Pro- Panel (or click Control Panel).
grams item: 2.Double-click System (icon); System (icon) is in Per-
formance and Maintenance (category).
1. Click Start (menu), point to Settings and click Control 3.Click the Hardware (tab) > Device Manager (button).
Panel (or click Start > Control Panel). 4.Click “+” next to Other Devices (if its sub-items are not
2. Double-click System (icon); System (icon) is in shown).
Performance and Maintenance (category). 5.Right-click Universal Serial Bus (USB) Controller
3. Click Hardware (tab) > Device Manager (button). and select Uninstall > OK (if you don’t see the item
4. Double-click the device you wish to update/reinstall the then there is no need to take any further action).
driver for (you may need to click “+”). 6.Restart the computer and it will find the USB 2.0 con-
5. Look for the Update Driver button (check the Driver tab) troller.
and follow the on screen prompts.

What to Install D - 29
Windows XP Information

Authorized Driver Message WinXP Driver Installation Procedure


If you receive a message telling you that the driver you Note that X is the drive letter assigned to the CD/
are installing is not authorized (Digital Signature Not DVD-ROM drive.
Found), just click Yes or Continue Anyway to ignore
the message and continue the installation procedure. Chipset (WinXP)
1. Click 1.Install Chipset Driver > Yes.
You will receive this message in cases where the driv- OR
er has been released after the version of Windows you
Click Start (menu) > Run... and navigate
are currently using. All the drivers provided will have
already received certification for Windows. (Browse..) to
X:\Drivers\01_Chipset\SETUP.EXE and
Version Conflict Message click OK.
During driver installation if you encounter any “file 2. Click Next.
version conflict” message, please click Yes to choose 3. Click the button to accept the license, and then
to keep the existing (newer) version. click Next.
4. Click Next > Next > Next.
New Hardware Found 5. Click Finish to restart the computer.
If you see the message “New Hardware Found”
(Found New Hardware Wizard) during the installa-
tion procedure (other than when outlined in the driver
install procedure), click Cancel to close the window,
D and follow the installation procedure as directed.

D - 30 What to Install
Windows XP Information

Video (WinXP) Audio (WinXP)


1. Click 2.Install Video Driver > Yes. 1. Click 4.Install Audio Driver > Yes.
OR OR
Click Start (menu) > Run... and navigate Click Start (menu) > Run... and navigate
(Browse..) to (Browse..) to
X:\Drivers\02_Video\setup.exe and click OK. X:\Drivers\04_Audio\SETUP.EXE and click
2. Click Finish. OK.
2. Click Next > Next > Next.
Modem (WinXP) 3. Click Finish to restart the computer.
1. Click 3.Install Modem Driver > Yes.
OR LAN (WinXP)
Click Start (menu) > Run... and navigate 1. Click 5.Install LAN Driver > Yes.
(Browse...) to OR
X:\Drivers\03_Modem\ssetup.exe and click OK. Click Start (menu) > Run... and navigate
2. Click OK. (Browse...) to
3. The modem is ready for dial-up configuration. X:\Drivers\05_LAN\WinSetup.exe and click
OK.
 2. Click OK.
Modem Country Selection
3. The network settings can now be configured.
Be sure to check if the modem country selection is appropriate
for you (Control Panel > Phone and Modem Options). D

What to Install D - 31
Windows XP Information

TouchPad (WinXP) Hot Key (WinXP)


1. Click 6.Install TouchPad Driver >Yes 1. Click 8.Install Hotkey Driver > Yes.
OR OR
Click Start (menu) > Run... and navigate Click Start (menu) > Run... and navigate
(Browse..) to (Browse..) to
X:\Drivers\06_Touchpad\Win- X:\Drivers\08_Hotkey\Setup.exe and click
WDF\x86\dpinst.exe and click OK. OK.
2. Click Next > Next > Next. 2. Choose the language you prefer, and click OK.
3. Click Finish to restart the computer. 3. Click Next.
4. Click Finish to restart the computer.
CardReader (WinXP)
1. Click 7.Install CardReader Driver > Yes.
OR
Click Start (menu) > Run... and navigate
(Browse...) to
X:\Drivers\07_CardReader\Setup.exe and
click OK.
2. Click Next > Next.
3. Click Finish to restart the computer.
D

D - 32 What to Install
Windows XP Information

802.11 b/g USB WLAN Module


Before installing the 802.11b/g USB WLAN driver, make sure that the optional

Wireless LAN module is on. Use the Fn + F11 key combination (see “Function Wireless Device
Operation Aboard
Keys” on page 1 - 11) to toggle power to the Wireless LAN module. Make sure
Aircraft
you install the drivers in the order indicated in Table D - 2, on page D - 27.
The use of any portable
electronic transmission de-
802.11 b/g WLAN Driver Installation vices aboard aircraft is usu-
1. Make sure the module is powered on, and then insert the Device Drivers & ally prohibited. Make sure
the module(s) are OFF if
Utilities + User’s Manual CD-ROM (WinXP) into the CD/DVD drive. you are using the computer
2. Click Install Option Drivers. aboard aircraft.
3. Click 1.Install WLAN Driver > Yes.
Use the Fn + F11 key com-
OR bination to toggle power to
Click Start (menu) > Run... and navigate (Browse...) to the WLAN module, and
X:\Drivers\Option\09_WLAN\Setup.exe and click OK. check the indicator to see if
the module is powered on
4. Choose the language you prefer, and click OK. or not (see Table 1 - 3, on
5. Click Next. page 1 - 9/ Table 1 - 6, on
6. Click Finish to complete the installation. page 1 - 11).
7. The operating system is the default setting for Wireless LAN control in Win-
dows XP (see overleaf).
8. Access any available wireless networks from Network Connections >
Wireless Network Connection menu in Windows (see sidebar overleaf), or
click the icon in the taskbar, and click View Wireless Connections. D

802.11 b/g USB WLAN Module D - 33


Windows XP Information


Network
Connection
Use the Windows Net-
work Connections con-
trol panel to access
available wireless net-
works (Start > Settings >
Network Connections
or Start > Connect To >
Show all Connections).

Figure D - 18
Wireless Network
Control Panels

D - 34 802.11 b/g USB WLAN Module


Windows XP Information

Bluetooth Module
Before installing the Bluetooth driver, make sure that the optional Bluetooth mod-

ule is on. Use the Fn + F12 key combination (see “Function Keys” on page 1 - 11) Wireless Device
Operation Aboard
to toggle power to the Bluetooth module. Make sure you install the drivers in the
Aircraft
order indicated in Table D - 2, on page D - 27.
The use of any portable
electronic transmission de-
Bluetooth Driver Installation vices aboard aircraft is usu-
1. Make sure the module is powered on, and then insert the Device Drivers & ally prohibited. Make sure
the module(s) are OFF if
Utilities + User’s Manual CD-ROM (WinXP) into the CD/DVD drive. you are using the computer
2. Click Install Option Drivers. aboard aircraft.
3. Click 2.Install Bluetooth Driver > Yes.
Use the Fn + F12 key com-
OR bination to toggle power to
Click Start (menu) > Run... and navigate (Browse...) to the WLAN module, and
X:\Drivers\Option\10_Bluetooth\Setup.exe and click OK. check the indicator to see if
the module is powered on
4. Click Install Software Drivers v2.3.0.1. or not (see Table 1 - 3, on
5. Choose the language you prefer, and click OK, and then click Next. page 1 - 9/ Table 1 - 6, on
6. Click the button to accept the license agreement, and then click Next. page 1 - 11).
7. Click Next > Next > Install.
8. Click Finish.
9. You can configure the settings at any time by going to the IVT Corporation
BlueSoleil - Main Window control panel (Start > Programs/All Pro-
grams > IVT BlueSoleil), or by clicking the taskbar icon . D

Bluetooth Module D - 35
Windows XP Information


User Guide
View the BlueSoleil User
Guides from the Help
Menu (or press the F1
key) in the IVT Corpora-
tion BlueSoleil - Main
Window control panel.
Click BlueSoleil User
Guides in the Contents
tab, and click to select the
appropriate User Guide
from the panel on the
right.

Figure D - 19
Bluetooth Control
Panel & User Guides

D - 36 Bluetooth Module
Windows XP Information

Bluetooth Local Area Connection Icon


If you want to display the Local Area Connection icon for the Bluetooth connection 
in the taskbar, set it up as follows: Disconnecting
1. Access the Network Connections control panel in Windows (Start > Settings > Net- In order to have the taskbar
work Connections OR Start > Connect To > Show all Connections) or by clicking the icon display the correct
taskbar icon . connection status, you will
2. Right-click the Bluetooth connection icon, and select Properties. need to exit the IVT Corpo-
ration BlueSoleil - Main
3. Click to put a tick in the “Show icon in the notification area when connected” box. Window by clicking the File
4. Close the control panels and the icon for the Bluetooth connection will be displayed menu and selecting Exit
in the taskbar when connected (see sidebar and overleaf). (see over).

After exiting the program


you can then use the Fn +
F12 key combination to turn
off the Bluetooth module.

If you use the close button,


or turn off the Bluetooth
module (by using the Fn +
F12) the taskbar icon will
not display the correct sta-
tus

Figure D - 20
Local Area
Connection
D

Bluetooth Module D - 37
Windows XP Information

5. Use the Fn + F12 key combination to turn on the Bluetooth module.


6. Run the IVT Corporation BlueSoleil program from the desktop icon or Start menu.
7. The connection status will then be displayed.

Figure D - 21 - Bluetooth Connected


8. To disconnect click File from the IVT Corporation BlueSoleil - Main Window, and select Exit (the Local Area
Connection will then display “A network cable is unplugged”).
9. Do not use the close button or Fn + F12 key combination before clicking File > Exit or the correct status will
not be displayed.
10. You can then use the Fn + F12 key combination to turn off the Bluetooth module (check the LED icon for the
Bluetooth module power status).

D
Figure D - 22 - Bluetooth Disconnected

D - 38 Bluetooth Module
Windows XP Information

PC Camera Module
There are 3 (300K or 1.3M pixel) camera options available for this computer, de- 
pending on your purchase configuration. The 1.3M pixel camera module has both Taking Still Pictures
UVC (USB Video Class) and non UVC options.
Double-click the My
Computer icon on the
Before installing the PC Camera driver, make sure that the optional PC Camera is desktop, or go the Start
on. Use the Fn + F10 key combination (see “Function Keys” on page 1 - 11) to menu and point to My
toggle power to the PC Camera module. Make sure you install the drivers in the Computer, then click it.
order indicated in Table D - 2, on page D - 27. Double-click the Bison-
.

Cam, NB Pro icon.


Latest PC Camera Driver Information Click Take a new picture
in the Camera Tasks
Check the CD, and any accompanying insert pages for the latest updated information on box.
the PC Camera driver, that may override the information provided here.

PC Camera Module D - 39
Windows XP Information

PC Camera Driver Installation


 1. Make sure the module is powered on, and then insert the Device Drivers &
Stand by/Hibernate Utilities + User’s Manual CD-ROM (WinXP) into the CD/DVD drive.
or Shutdown Error 2. Click Install Option Drivers.
The computer may stop
3. Click 3.Install Camera Driver > Yes.
responding when you OR
put it into (or resume Click Start (menu) > Run... and navigate (Browse...) to
from) Stand By or Hiber- X:\Drivers\Option\11_Camera\Launch.exe and click OK (for non UVC
nate, or when you shut Cameras).
down.
OR
This error is caused by X:\Drivers\Option\12_UVC_Camera\setup.exe and click OK (for UVC
power management Cameras).
within Windows XP,
when applied to a PC For non UVC Cameras:
Camera attached to the 4. Click Install Products.
internal USB hub. 5. Choose the language you prefer and click OK.
Microsoft has posted a
6. Click Next > Finish to restart the computer.
Hotfix for this error on its For UVC Cameras:
website (search for Hot-
fix KB909667). 7. Click Next > Next.
8. Click Finish to restart the computer.
Download and install the 9. Run the BisonCap application program from the BisonCam shortcut on the
Hotfix to correct this er-
desktop, or from the BisonCam item in the Start > Programs/All Programs
ror.
D menu (if the hardware is turned off use the Fn + F10 key combination to turn
it on again).

D - 40 PC Camera Module
Windows XP Information

PC Camera Audio Setup


If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in
Windows.

1. Go to the Start menu and point to Settings (or just click Control Panel) and click Control Panel, then double-
click the Sounds & Audio Devices icon (Sounds, Speech, and Audio Devices in Category View).
2. Click Advanced in the Volume > Device volume tab.
3. Click Options and scroll down and click Properties.
4. Select HD Audio rear input (for a microphone plugged in to the microphone-in jack)/HD Audio Front Mic (for
the built-in microphone) from the Mixer device menu and click OK (make sure there is a tick in the Microphone
tick box).
5. Click Recording (button) and click OK.
6. Boost the volume in the Microphone section as high as it will go (make sure there is a tick in the Select tick box
if you have selected HD Audio rear input).
7. Close the open windows.
8. You can also boost the microphone from the Mixer in the VIA Audio Deck menu (see page D - 6).
9. Run the BisonCap application program from the Start > Programs/All Programs > BisonCam menu.
10. Go to the Devices menu heading and select HD Audio rear input OR HD Audio front mic (it should have a
tick alongside it).
11. Go to the Capture menu heading and select Capture Audio (it should have a tick alongside it).

PC Camera Module D - 41
Windows XP Information

Figure D - 23
Audio Setup

D - 42 PC Camera Module
Windows XP Information

BisonCap
BisonCap is a video viewer useful for general purpose video viewing and testing, 
and can capture video files to .avi format. Pre-Allocating File
Space
1. Run the BisonCap application from the Start > Programs/All Programs > Bison-
Cam menu (it is recommended that you set the capture file before the capture You may pre-allocate the
process - see Set Capture File below). file size for the capture file
2. Go to the Capture menu heading (if you wish to capture audio check “PC Camera in the BisonCap pro-
Audio Setup” on page D - 41) and select Start Capture. gram. You can choose to
ignore this by clicking
3. On the first run of the program (if you have not set the captured file) you will be
Cancel.
asked to choose a file name and size (see the sidebar - Pre-Allocating File
Space) for the captured file. Click Start Capture again. Pre-allocating space on
4. Click OK to start capturing the video, and press Esc to stop the capture. the hard disk can improve
5. If you wish to, you may go to the File menu and select Save Captured Video As..., the capture quality (par-
choose a file name and location, and then click Open (you can view the file using ticularly of large capture
the Windows Media Player). files), by reducing the
amount of work the hard
disk has to do in finding
Set Capture File space for the video data
In the BisonCap program you will only be asked to set the capture file name on the as it is being captured.
first run of the program. When you run the program the next time the file will auto- You may find it helpful to
matically be overwritten with the newly captured file. To avoid overwriting files you defragment the HDD be-
can go to the Set Capture File.. option in the File menu, and set the file name and fore capture.
location before capture. Set the name and location then click Open (you can choose
Cancel to ignore the file size if prompted). D

PC Camera Module D - 43
Windows XP Information

Eliminating Screen Flicker


If you find that the video screen in the BisonCap program is flickering, you can try
to adjust the setting in the Video Capture Filter options.
1. Run the BisonCap application.
2. Go to Options and scroll down to select “Video Capture Filter...”.
3. Click either 50Hz or 60Hz under Frequency in Property Page (tab).

Figure D - 24
Video Capture Filter

D - 44 PC Camera Module

You might also like