Scribd
Upload
138 views7 pages

Car Programming Vin

The document provides steps for adding a dealer key to a vehicle's immobilizer system using the VAG KM+IMMO Tool in two conditions: 1) When at least one existing key can be used, the process involves reading the EEPROM, generating a dealer key, writing new key data, and adding the key ID. 2) When all keys are lost, it requires putting the system in service mode, loading saved EEPROM data, writing it back, and then generating a new dealer key. The device and car must remain connected throughout to avoid needing to restart.

Uploaded by

MohamedBenMansour
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
138 views7 pages

Car Programming Vin

The document provides steps for adding a dealer key to a vehicle's immobilizer system using the VAG KM+IMMO Tool in two conditions: 1) When at least one existing key can be used, the process involves reading the EEPROM, generating a dealer key, writing new key data, and adding the key ID. 2) When all keys are lost, it requires putting the system in service mode, loading saved EEPROM data, writing it back, and then generating a new dealer key. The device and car must remain connected throughout to avoid needing to restart.

Uploaded by

MohamedBenMansour
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

VAG KM+IMMO Tool

Process of adding dealer key with Tango

1. Condition 1: At least one key can be used.

1) Connect “VAG KM+IMMO Tool” to both pc and car.

2) Click “EEPROM” button, read EEPROM and save it for backup.

3) Click “Dealer Key” button, open “Dealer key” dialog.

4) Use the prompt key chip to make key.

Nec24c32 and Nec24c64: Megamos 48

CDC VW: TP23

CDC Audi: TP25

CDC Skoda: TP24

CDC Seat: TP22


5) Switch to Tango, read “Word 1” data and “Key ID” data.
6) Switch back to “Dealer key” dialog, input “Page(Word) 1” data, and

click “Calculate Dealer Key Data” button.

7) Switch to Tango, write Word 6-11(for Nec24c32 and 24c64, you need

write additional Word 4 and Word 5).

8) In Tango, write Word 1 to lock the key.

9) Switch back to “Dealer key” dialog, click “Close”, and then click

“IMMO” button to open “Immo Info” dialog.


10) Input “New Key ID” with key id data read from step 5, then click “Add

Key” button.

11) Finish.
2. Condition 2: All keys are lost

1) Connect “VAG KM+IMMO Tool” to both pc and car.

2) Click “Service Mode” button to open “Service Mode” dialog.

3) Remove the 24C32 chip from instrument, read 24C32 EEPROM data

with programmer, and save EEPROM.


4) Switch to “Service Mode” dialog, load EEPROM.

5) Save special EEPROM, write data to 24C32 EEPROM back to the chip,

and install chip back in instrument.

6) Save KEY file.

7) Login with the key file.

8) Write back the original EEPROM.

9) Close “Service Mode” dialog, start adding dealer key from Step 3 of

Condition 1 above.

Note: Before the process is complete, keep the PC and device

connected with vehicle, do NOT disconnect. If you interrupt, you

need to re-start from the first step.

You might also like