Leliwa Technical Bulletin

MSC in Pool

Date:
Date: 15.07.2009
Revision: 004/MIP/009
Author: Jakub Bluszcz
Copyright ©2010 Leliwa. All Rights Reserved.

1
 Leliwa Technical Bulletin MSC in Pool

Table of contents

Topic Page

Introduction.....................................................................................................3
Network Resource Identification .....................................................................5
Node Selection Function.................................................................................6
Mobility Management....................................................................................10
Acronyms and Abbreviations ........................................................................12
References ...................................................................................................13
Disclaimer.....................................................................................................14

2
MSC in Pool Leliwa Technical Bulletin

Introduction
The MSC in Pool, as a part of Intra Domain Connection of RAN Nodes to
Multiple CN Nodes solution, overcomes the strict hierarchy, which restricts
the connection of a BSC node to just one MSC. This restriction results from
routing mechanisms in the BSC which differentiate only between information
to be sent to the MSC (CS domain) or to the SGSN (PS domain) and which
do not differentiate between multiple CN nodes in each domain. The MSC in
Pool solution introduces a routing mechanism and other related functionality,
which enables the BSC to route information to different CN nodes within the
CS or PS domain, respectively.

MSC1 MSC2 MSC3

BSC1 BSC2 BSC3 BSC4 BSC5 BSC6

Figure 1 MSCs in Pool (logical view)

The MSC in Pool solution introduces further the concept of ‘pool-areas’ which
is enabled by the routing mechanism in the BSC. An MSC pool-area is
comparable to an MSC service area as a collection of one or more BSC
service areas. In difference to an MSC service area a pool-area is served by
multiple MSCs in parallel which share the traffic of this area between each
other. Furthermore, pool-areas may overlap which is not possible for the
MSC service areas. From a BSS perspective a pool-area comprises all LAs
of one or more BSC that are served by a certain group of MSC nodes in
parallel. One or more of the MSCs in this group may in addition serve LAs
outside this pool-area or may also serve other pool-areas. This group of
MSCs is also referred to as MSC pool.
The MSC in Pool enables a few different application scenarios with certain
characteristics. The service provision by multiple MSCs within a pool-area
enlarges the served area compared to the service area of one MSC. This
results in reduced inter MSC LA updates and it reduces the HLR update
traffic. The configuration of overlapping pool-areas allows to separate the
overall traffic into different MS moving pattern, e.g. pool-areas where each
covers a separate residential area and all the same city centre. Other
advantages of multiple MSCs in a pool-area are the possibility of capacity
upgrades by additional MSCs in the pool-area or the increased service

3
 Leliwa Technical Bulletin MSC in Pool

availability as other MSCs may provide services in case one MSC in the pool-
area fails.

MSC7
MSC2 MSC4
MSC6
MSC1 MSC3
MSC5

BSC3
BSC7
BSC2 BSC4 BSC5 BSC8
BSC6
BSC1

Pool-area 1 Pool-area 2 Pool-area 3

Figure 2 Pool area configuration example

An MS is served by one dedicated MSC node of a pool-area as long as it is in

radio coverage of the pool-area. Fig. 11-2 shows most of the possible pool-
area configurations. It contains Pool-area 1 (BSC area 1, 2 and 3 served by
MSCs 1 and 2), Pool-area 2 (BSC area 4 and 5 served by MSCs 3 and 4) and
Pool-area 3 (BSC area 5, 6 and 7 served by MSCs 5, 6 and 7). In addition the
BSC areas 8 is served by MSC 7 without any usage of the MSCs in Pool
feature. The possibility to configure overlapping pool-areas is shown by the
Pool-areas 2 and 3. The Pool-area 1 is configured non-overlapping with any
other Pool-area. The number or capacity of MSCs is configured
independently for each pool-area. The usage of MSCs in Pool may be
configured in parts of the network only and can co-exists with other areas not
using this feature.

4
MSC in Pool Leliwa Technical Bulletin

Network Resource Identification

Identification
An MSC pool-area is an area within which an MS roams without a need to
change the serving MSC. A pool-area is served by one or more MSCs nodes
in parallel. The complete service area of a BSC belongs to the same one or
more pool-area(s). An BSC service area may belong to multiple pool-areas,
which is the case when multiple overlapping pool-areas include this BSC
service area. If LAs span over multiple BSC service areas then all these BSC
service areas have to belong to the same pool-area.

BSC3

MSC3

MSC2 BSC1

MSC1

BSC2

An MSC pool-area is an area within which an MS roams

without a need to change the serving MSC.

Figure 3 Pool-area definition

The Network Resource Identifier (NRI) identifies uniquely an individual MSC

out of all MSCs, which serve in parallel a pool-area. The length of the NRI is
the same in all MSCs in one pool-area. In areas where pool-areas overlap the
NRI identifies uniquely an MSC out of all MSCs, which serve all these
overlapping pool-areas, i.e. an NRI identifies uniquely an MSC within a BSC.
In case of overlapping pool-areas the NRI length is configured to be the same
in all the nodes serving these pool-areas. More than one NRI may be
assigned to an MSC.
The NRI is part of the TMSI, which is assigned by the serving MSC to the MS.
The TMSI allocation mechanism in the MSC generates TMSIs which contain
a configured NRI in the relevant bit positions. The NRI has a flexible length

5
 Leliwa Technical Bulletin MSC in Pool

between 10 and 0 bits (0 bits means the NRI is not used and the feature is
not applied).
The NRI is coded in bits 23 to 14 of TMSI. Regardless of the NRI length the
most significant bit of the NRI is always in bit 23 of TMSI.

octet 4 octet 3 octet 2 octet 1

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

NRI

NRI - Network Resource Identification

Figure 4 Structure of TMSI

The BSC node derives the NRI from any initial signalling message. The BSC
masks the significant bits out of the TMSI to determine the NRI, which
identifies the MSC. It is configured in the BSC which bits out of TMSI
provided by the MS are significant for the NRI.
The change of a pool-area is not visible to the MS. In general there is no
need to detect a pool-area change. It may be advantageous for load
balancing purposes to detect pool-area changes in the network to distribute
MSs entering a pool-area to MSCs with an appropriate load status. MSs
changing a pool-area may be detected by configuration of different NRI
values for adjacent pool-areas.

Node Selection Function

This function is used in BSC and potentially in MSCs. In the BSC the function
selects the specific MSC to which initial signalling messages are routed. The
NRI identifies the specific MSC. If the Node Selection Function has an MSC
address configured for the NRI derived from the initial signalling message is
routed to this address. If no MSC address is configured for the derived NRI or
if no NRI can be derived (e.g. the MS indicated an identity which contains no
NRI) then the Node Selection Function selects an available MSC (e.g.
according to load balancing) and routes the message to that MSC.

6
MSC in Pool Leliwa Technical Bulletin

MSC1
(NRI=1)
TMSI (NRI=2) BSC1

MSC2
(NRI=2)
TMSI (NRI=2) BSC2

 MSC3

Node Selection Function (NSF) (NRI=3)
 TMSI/NRI allocation
 NRI routing
Figure 5 Use of NRI

In case an MSC/VLR sends a paging with IMSI (i.e. the paging message
does not contain a TMSI), the node selection function in the BSC upon
reception temporarily stores the identity of the MSC that issued the paging
message. If the node selection function receives a paging response with an
IMSI then it checks the temporarily stored identities of the MSCs on entries
matching this IMSI and forward the paging response to the node identified by
this identity.

Paging Req.
(IMSI)
MSC
BSC pool
 Paging
Res. (IMSI) MSC

IMSI – MSC ID

Figure 6 Paging with IMSI

If the MSC/VLR initiates the paging procedure via Gs-interface the SGSN has
to add the MSC/VLR-identity to the paging message.

7
 Leliwa Technical Bulletin MSC in Pool

MSC

pool
MSC

Paging Req. (IMSI)

 Paging Res. (IMSI)

BSC SGSN
 Paging  Paging
Req. (IMSI) (IMSI + MSC/VLR-
identity)

Figure 7 CS paging via Gs interface

Load balancing
The Node Selection Function in the BSC balances the load between the
available MSCs. This is performed by an appropriate selection of the MSC for
an MS:
• which was not yet assigned to an MSC, i.e. when there is no MSC
configured for the NRI indicated by the MS,
• when no NRI can be derived,
• in exceptional cases, e.g. when the MSC corresponding to an NRI
cannot be reached.
The load-balancing algorithm is implementation specific.
In case of handover into a pool-area a load balancing between all the target
MSC nodes serving this pool-area is gained by configuration. Source MSCs
which support MSC in Pool may be configured with all possible target MSCs
for each handover target. Source MSC which do not support MSC in Pool can
configure only one target MSC per handover target. In this case each of
source MSCs which handover to the same pool-area may be configured with
another target MSC out of all target MSCs serving the same handover target.
The mechanism for distribution of the traffic between the handover target
MSCs is implementation specific. This load balancing is complemented by
the Node Selection Function in the BSS, which distributes MSs between the
MSCs when these MSs enter the pool-area in idle mode.

Load Re-
Re-Distribution
There are situations where a network operator wishes to remove load from
one MSC in an orderly manner (e.g. to perform scheduled maintenance, or,

8
MSC in Pool Leliwa Technical Bulletin

to perform load re-distribution to avoid overload) with minimal impact to end

users and/or additional load on other entities. The re-distribution procedure
does not require any new functionality in the terminal, that is, all terminals can
be moved.
Re-distribution of MSs is initiated via an O&M command in the MSC, which
needs to be off-loaded.
In a first phase (a couple of Periodic LA Update periods long), MSs doing LA
Update are moved to other MSCs in the pool. When the MSC receives the,
LA Update request, it returns a new TMSI with a null-NRI, and a non-
broadcast LAI in the accept message. The non-broadcast LAI causes the MS
to immediately send a new Location Update, which the BSC node then routes
to a new MSC due to the null-NRI.

MSC
Null-NRI,
non-broadcast LAI (NRI=1)

O&M

 LA Upd. (periodic)
BSC MSC
 LA Upd. Accept ( )
(NRI=2)

 LA Upd. (periodic)

MSC
(NRI=3)

Figure 8 Load Re-Distribution (phase 1)

A second phase includes scanning through remaining MSs and initiating a

move of them to other MSCs by allocating to these MS a new TMSI using the
TMSI re-allocation procedure (with null-NRI and non-broadcast LAI) so that a
Location Update is triggered when the ongoing CM transaction ends, which
will cause them to be moved.

Null-NRI,
non-broadcast LAI

TMSI re-allocation ( )
MSC
BSC (NRI=2)

 LA Upd.
MSC
(NRI=3)

Figure 9 Load Re-Distribution (phase 2)

9
 Leliwa Technical Bulletin MSC in Pool

The MSs being moved from one MSC are stopped from registering to the
same MSC again by an O&M command in BSCs connected to the pool. The
MSs moving into a pool area are also stopped from registering into an MSC
being off-loaded in the same manner.

Mobility Management
An MS performs LA Updates, which may result in a change of the serving
MSC. In these procedures the new MSC requests from the old MSC MS
specific parameters. If multiple MSCs are configured in the new MSC for the
old LA indicated by the MS then the new MSC derives the NRI from the old
TMSI indicated by the MS. The new MSC uses the old LA together with the
NRI to derive the signalling address of the old MSC from its configuration
data.

old pool
MSC
(NRI=1)

MSC

(NRI=2) Send Identification /


 LA Update Request Send Parameters
(TMSI, old LAI)
MSC
 NRI & old LAI ► MSC/VLR number

Figure 10 MSC change (new MSC outside old pool)

If the network contains MSCs that cannot derive the old MSC from LAI and
NRI a default MSC for each LA is used to resolve the ambiguity of the
multiple MSCs serving the same area.

Default MSC and backwards compatibility

MSCs that can only derive one MSC from the LAI (e.g. because they do not
support the MSC in Pool feature, or no detailed knowledge of the NRIs is
configured) are not aware, that multiple MSCs may serve a LA. These nodes
can therefore contact only one MSC (a default MSC) per LA.
A default MSC resolves the ambiguity of the multiple MSCs per LA by
deriving the NRI from the TMSI. The default MSC relays the signalling
between the new MSC and the old MSC.

10
MSC in Pool Leliwa Technical Bulletin

Note that the default MSC is configured per LA. So different MSCs in a
network might have configured different default MSCs for a LA. With this
approach more than one of the MSCs that serve a pool-area can be used as
default MSC, so load concentration on one MSC and a single point of failure
can be avoided.

old pool
MSC
(default) 
MSC

Send Identification

/ Send Parameters
 LA Update Request
(TMSI, old RAI)
MSC
 LAI ► default MSC number

Figure 12 Default MSC

11
 Leliwa Technical Bulletin MSC in Pool

Acronyms and Abbreviations

BSC
BSC Base Station Controller
BSS Base Station System
CM Connection Management
CN Core Network
CS Circuit Switching
CS Convergence Sublayer
HLR Home Location Register
IMSI International Mobile Subscriber Identity
LA Location Area
LAI Location Area Identity
MS Mobile Station
MSC Mobile Switching Center
NRI Network Resource Identifier
PS Packet Switch
RAI Routing Area Identity
RAN Radio Access Network
SGSN Serving GPRS Support Node
TMSI Temporary Mobile Subscriber Identity
VLR Visitor Location Register

12
MSC in Pool Leliwa Technical Bulletin

References
This section contains the locations of various specifications, document
references and useful information where you can learn more about this
subject.

[1] 23.236 Intra-domain connection of Radio Access Network (RAN)

nodes to multiple Core Network (CN) nodes

[2] 23.002 Network architecture

[3] 23.060 General Packet Radio Service (GPRS); Service description;

Stage 2

[4] 48.008 Mobile Switching Centre - Base Station system (MSC-BSS)

interface; Layer 3 specification

[5] 23.003 Numbering, addressing and identification

13
 Leliwa Technical Bulletin MSC in Pool

Disclaimer
This document is based on Leliwa training materials.

Information in this document is subject to change without notice. Leliwa

assumes no responsibility for any errors that may appear in this document.

This document may be freely redistributed. You can store it on any servers
and make it available for public download. In such case it must be clearly
indicated that it comes from Leliwa website www.leliwa.com

If you received only this file, you can download more Leliwa Technical
Bulletins from the following address:
http://www.leliwa.com/downloads

If you want to be informed when the new bulletins are uploaded, please send
a blank e-mail with Subject="Update_request" to [email protected] or
click this link: mailto:[email protected]?subject=Update_request

Leliwa Sp. z o.o. Leliwa Telecom AB

Plebiscytowa 1.122 Orrpelsvägen 66

PL-44-100 Gliwice SE-167 66 BROMMA
Poland Sweden
GPS: N50.2981°, E018.6561° GPS: N59.3260°, E17.9464°

telephone: +48 32 376 63 05 telephone: +46 8 4459430

fax: +48 32 376 63 07 email: [email protected]
Skype: leliwa_poland
email: [email protected]

14