Archives Volume 28 International Scientific Journal

Issue 6 published monthly as the organ of

of Materials Science June 2007 the Committee of Materials Science
and Engineering Pages 345-348 of the Polish Academy of Sciences

The influence of casting temperature on

castability and structure of AJ62 alloy
A. Kie³bus*
Department of Materials Science, Silesian University of Technology,
ul. Krasiñskiego 8, 40-019 Katowice, Poland
* Corresponding author: E-mail address: [email protected]
Received 05.03.2007; accepted in revised form 15.05.2007

ABSTRACT

Purpose: The AJ62 magnesium alloy exhibit good elevated-temperature tensile properties, excellent creep
resistance and good castability. This alloy contains approximately 6% aluminum and about 2.5% strontium.
Typically, it is used in automotive industry for the engine crankcase and power-train components. The aim of this
paper is to present the results of the influence of pouring temperature on the fluidity and microstructure of the
AJ62 magnesium alloy.
Design/methodology/approach: The study was conducted on AJ62 magnesium alloys. Sand casting was
performed at 695-755°C temperatures. The spiral test of fluidity was used. The microstructure was characterized
by optical microscopy (Olympus GX-70) and a scanning electron microscopy (Hitachi S3400) equipped with an
X-radiation detector EDS (VOYAGER of NORAN INSTRUMENTS). The phase identification of these alloys
was identified by X-ray diffraction (JDX-75). Quantitative examination was conducted using the “MET-ILO”
automatic image analysis programme.
Findings: In as cast condition AJ62 alloy consisted of α-Mg grains with some types of intermetallic phases:
(Al,Mg)4Sr , Al8Mn5 and Al3Mg13Sr. The flow length and the intermetallicphases area fraction increase with
increase the pouring temperature.
Research limitations/implications: Future researches should contain investigations of the influence of
casting temperature and heat treatment parameters on mechanical properties of AJ62 magnesium alloy.
Practical implications: The established casting parameters (mainly temperature) can be useful for preparing
sand and die casting technology of the AJ62 magnesium alloy.
Originality/value: The relationship between the initial structure, casting temperature, castability and phase
composition in AJ62 magnesium alloy was specified.
Keywords: Metallic alloys; Manufacturing and processing; Casting; AJ62 magnesium alloy

MATERIALS

1. Introduction
Introduction properties of Mg–Al based alloys is due to precipitation of
Mg17Al12 from the supersaturated solid solution and coarsening of
this phase in the interdendritic regions at high temperatures. The
Magnesium alloys with aluminum characterize a good
service temperatures of automotive powertrain components are
mechanical properties, corrosion resistance and castability after
mostly above 150°C, therefore, creep resistance is a major
sand and die casting. However, they have poor creep properties at
requirement for use of magnesium in critical automotive
elevated temperature, higher than ~125°C [1-3]. Mg-Al alloys are
components [7, 8].
characterized by solid solution -Mg with precipitates of Possible approaches to improving creep resistance of Mg-Al
Mg17Al12 intermetallic phase [4-6]. The poor elevated temperature alloys include introducing [1]:

© Copyright by International OCSCO World Press. All rights reserved. 2007 345
 A. Kie³bus

alloying elements with higher affinity to aluminum;

secondary phase particles at grain boundaries to pin the
sliding phenomenon;
a fine dispersion of stable precipitates.
Many magnesium alloys with addition of Sr have emerged in
the 1990s and 2000 [9]. The magnesium alloys with strontium
exhibit good elevated-temperature tensile properties, excellent
creep resistance and good castability [1]. Strontium is added for
creep resistance in die casting and gravity casting alloys or to
reduced shrinkage porosity. Sr level may range from 0,02% to
3%. The preferred alloying temperature is around 675-700°C [9].
These alloys were targeted for automotive applications such as oil
pans, cylinder blocks (~ 200°C) or engine pistons housings (~
250°C) [9, 10].
Fluidity is defined as the ability for a molten metal to flow
through and to fill a mould cavity before solidification occurs
[11]. It gives the ability to determine if an alloy is suitable to cast
into a certain product with good quality. It will depend on the die
design, pouring system, mould materials, casting parameters and
chemical composition of alloy [12]. It is obvious that aluminium, Fig. 1. Diagram of spiral sample to investigations of fluidity
zinc, silicon and rare earths increase castability [12, 13], while
calcium decreases it (some authors report that RE decreases
castability of magnesium alloys) [14]. The increasing of the
fluidity length with increasing rare earths and strontium content
has been attributed to the reduction in the freezing range of the
alloys and the high latent heat of RE and Sr containing
precipitates, which may act to slow the solidification [15]. In
general terms, short freezing range alloys have higher fluidity
than long freezing range alloys [12].

Picture B
Picture A
of the
2. Description of thework
workmethodology
methodology input image
gray image, normalization,
shadow correction
andand material
material forfor research
research.

2.1. Material forresearch

Material for research
The material for the research was AJ62 magnesium alloy. The
chemical composition of this alloy is provided in Table 1.

Table 1.
Chemical composition of the AJ62 alloy Picture D
Picture C
Alloy Mg Al Mn Sr removal small objects
binarisation,
image for measurement
AJ62 balance 6.1 0.34 2.1
Fig. 2. The procedure of intermetallic phases detection, LM

2.2. Research methodology

2.2. Research methodology
3. Description
Description of
of achieved
achieved results
results of
of own
own
Fluidity has been investigated by determining the flow length researches
with a mould featuring a spiral shaped cavity. The shape of researches
fluidity spiral is shown in Fig.1. Casting in sand moulds has been
done at different melt temperature from 695°C up to 755 °C.
For the microstructural observation, a OLYMPUS GX 71 3.1. Microstructure
Microstructure of
ofthe
theAJ62
AJ62alloy
alloy
metallographic microscope and a HITACHI S-3400N scanning
electron microscope with a Thermo Noran EDS spectrometer The AJ62 magnesium alloy after sand casting is characterized
equipped with SYSTEM SIX were used. To measure the by the solid solution !"with""the lamellar eutectic (Al,Mg)4Sr +
stereological parameters, a program for image analysis “MET- solid solution ! and the globular precipitates of the Mn5Al8 phase.
ILO” was used. A set of grey image transformations until Morever the occurrence of not mumerous precipitates of the
obtaining a binary image are shown in Fig. 2. massive Al3Mg13Sr phase nave been provided (Fig.3).

346 346 Archives of Materials Science and Engineering

The influence of casting temperature on castability and structure of AJ62 alloy

Fig. 5. Spiral cast of AJ62 alloy after pouring from temperature

Fig. 3. The precipitates of (Al,Mg)4Sr, Mn5Al8 and Al3Mg13Sr
755°C. Fluidity length is equal 57 cm
phases in AJ62 alloy after sand casting

3.2. Influence
3.2. of pouring
Influence of pouringtemperature
temperatureonon
fluidity
3.3. Influence
3.3. of pouring
Influence of pouringtemperature
temperatureononvolume
fraction
volume of intermetallic
fraction phases
of intermetallic phases
fluidity
The area fraction of intermetallic phases (mainly eutectic
Spiral casts after pouring from temperature 695°C and 755 °C
(Al,Mg4Sr+ ) after sand casting from temperature 695°C was
were showed on figures 4 and 5, respectively. Table 2 shows the
equal AA=5.6% (Fig. 6).
influence of pouring temperature on filling lengths. Within a
temperature interval of about 60 °C the passes distance increase
up to a value 1,5 times above the original flow length of 38 cm.
The detected correlation can be explained by the extended interval
from pouring to freezing temperature.

Table 2.
Influence of pouring temperature on fluidity of AJ62 alloy
Pouring
695 715 735 755
temperature [°C]
Filling length [m] 0.38 0.48 0.53 0.57

Fig. 6. Microstructure of AJ62 alloy after pouring from tempe-

rature 695°C. The area fraction of intermetallic phases is equal
AA=5.6%

Table 3.
Influence of pouring temperature on area fraction of the
intermetallic phases
Pouring temperature [°C] 695 715 735 755
Area fraction AA [%] 5.6 5.8 6.6 7.0

The area fraction of intermetallic phases increases with

increase of pouring temperature (table 3). After casting from
Fig. 4. Spiral cast of AJ62 alloy after pouring from temperature temperature 755°C area fraction of intermetallic phases was equal
695°C. Fluidity length is equal 38 cm AA=7.0% (Fig. 7).

Volume 28 Issue 6 June 2007 347

 Acknowledgements
The present work was supported by the Polish Ministry of
Science and Higher Education under the research project No
PBZ-KBN-114/T08/2004.

References
[1] A.A. Luo, Recent magnesium alloy development for
automotive power train application, Materials Science
Forum 419-422 (2003) 57-65.
[2] B. Mordike, Development of highly creep resistant
magnesium alloys, Journal of Materials Processing
Technology 117 (2001) 391-394.
Fig. 7. Microstructure of AJ62 alloy after pouring from tempe- [3] M.O. Pekguleryuz, E. Baril, Creep resistant magnesium die
rature 755°C. The area fraction of intermetallic phases is equal casting alloys based an alkaline earth element, Materials
AA=7.0% Transactions 42 (2001) 1258-1267.
[4] A. Dahle, Y. Lee, M. Nave, P. Schaffer, D. StJohn,
Development of the as-cast microstructure in magnesium-
aluminium alloys, Journal of Light Metals 1 (2001) 61-72.
4. Summary
Summary [5] A. Kie bus, T. Rzycho!, R. Cibis, Microstructure of AM50 die
casting magnesium alloy, Journal of Achievements in Materials
and Manufacturing Engineering 18 (2006) 135-138.
The AJ62 magnesium alloy structure after sand casting is [6] A. Kie bus, J. Adamiec, J. Cwajna, J. Pa"ko, The influence
characterized by a solid solution structure with the lamellar of heat treatment on the microstructure of GA8 magnesium
eutectic (Al,Mg)4Sr + solid solution !"globular precipitates of the alloy, Journal of Achievements in Materials and
Mn5Al8 phase and not mumerous precipitates of the massive Manufacturing Engineering 20 (2007) 131-134.
Al3Mg13Sr phase. The area fraction of intermetallic phases [7] A.A. Luo, Recent magnesium alloy development for
(mainly eutectic (Al,Mg4Sr+ ) increase with increase of pouring elevated temperature applications, International Materials
temperature. Fluidity of AJ62 alloy linearly increases with Reviews 49 (2004) 13-32.
increase of pouring temperature and are fraction of intermetallic [8] B. Jing, S. Yangshan, X. Shan, X. Feng, Z. Tianbai, Microstru-
phases (Fig. 8). cture and tensile creep behavior of Mg–4Al based magnesium
alloys with alkaline-earth elements Sr and Ca additions,
Materials Science and Engineering A 419 (2006) 181-188.
10,0 1
area fraction [9] H. Friedrich, S. Schumann, Research for a “new age of
9,0 fluidity magnesium” in the automotive industry, Journal of
Materials Processing Technology 117 (2001) 276-281.
Area fraction of intermetallic phases

8,0 0,8

7,0 [10] W. Blum, P. Zhang, B. Watzinger, B. Grossmann,

Filling length [m]

6,0 0,6
Comparative study of creep of the die-cast Mg-alloys AZ91,
AS21, AS41, AM60 and AE42, Materials Science and
5,0
AA [%]

Enginieering A 319-321 (2001) 735-740.

4,0 0,4
[11] S. Lun Sin, D. Dube, Influence of process parameters od
3,0 fluidity of investment cast AZ91D magnesium alloy,
2,0 0,2 Materials Science and Enginieering A 386 (2004) 34-42.
1,0 [12] A.L. Bowles, Q. Han, J.A. Horton, Castability of
0,0 0 magnesium alloys, Magnesium Technology (2005) 99-104.
695 715 735 755 [13] W. Qudong, L. Yizhen, Z. Xiaoqin, D. Wenjiang, Z.
Pouring temperature [°C] Yanping, L. Qinghua, L. Jie, Study on the fluidity of
AZ91+xRE magnesium alloy, Materials Science and
Enginieering A 271 (1999) 109-115.
Fig. 8. The influence of pouring temperature on fluidity of AJ62
[14] E. Aghion, B. Bronfin, F. von Buch, S. Schumann, H.
magnesium alloy
Friedrich, Newly Developed Magnesium Alloys for
Powertrain Applications, JOM, 2003, 30-33.
The detected correlation can be explained by: [15] D. Argo, M.O. Pekguleryuz, P. Labelle, P. Vermette, R.
# the extended interval from pouring to freezing temperature, Bouchard, M. Lefebvre, Process parameters and diecasting
# the increase of area fraction of intermetallic phases. of Noranda’s AJ52 high temperature Mg-Al-Sr alloy,
Magnesium Technology (2002) 291-296.

348 348 READING DIRECT: www.archivesmse.org