Scribd Logo
Upload

Welcome to Scribd!

  • 2K views

    10 NanoGrout SG-Anchoring Resin PDF

    Uploaded by

    arunjacobn

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    10 NanoGrout SG-Anchoring Resin PDF

    Uploaded by

    arunjacobn
    2K views3 pages

    Original Title

    10 NanoGrout SG-Anchoring Resin.pdf

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    2K views3 pages

    10 NanoGrout SG-Anchoring Resin PDF

    Uploaded by

    arunjacobn

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    Construction Chemicals

    NanoGrout SG
    Epoxy Based Structural Adhesive & Anchor Grout

    DESCRIPTION NanoGrout SG is a two component, epoxy base, high strength, structural adhesive and
    anchor grout. It is available in paste and pourable grades.

    USES NanoGrout SG is used as epoxy grout for base plate bolt pockets, bar anchor, starter
    bars, bridge bearing, boom fixing, etc. It is also used for speedy and permanent patching
    repairs to concrete structures, bonding of precast concrete components, bridge
    bearings to concrete and all structural repair works where strength, impermeability to
    water and resistance to aggressive chemicals is essential.

    ADVANTAGES • High early strength


    • 3 to 4 times stronger than typical concrete
    • Good adhesion to most of the substrates
    • Excellent resistance to abrasion and impact
    • Corrosion resistant
    • Unaffected by a wide range of acids, alkalis and industrial chemicals
    • Suitable for dynamic loads
    • Two grades in paste and pourable variants
    • Tolerant to damp conditions

    TYPICAL PROPERTIES at 25°C

    PROPERTY TEST METHOD VALUE


    Component - Two: Part A- Base
    Part B- Hardner
    Mixed Form - Pourable Paste
    Colour - Grey when mixed
    Compressive Strength BS 6319-2 1 Day 45 N/mm² 50 N/mm²
    7 Days 80 N/mm² 70 N/mm²
    Flexural Strength BS 6319-3 7 Days 35 N/mm² 25 N/mm²
    Tensile Strength BS 6319-7 7 Days 25 N/mm² 20 N/mm²
    Bond Strength ASTM C882 7 Days 20 N/mm² 20 N/mm²
    Pot Life - 45-70 mins (2kg mixed material)
    Water Penetration BSEN 12930-8 Nil
    Chemical Resistance ASTM D 543 Resistant to alkalis, fuels, acids, oils, etc.

    SURFACE PREPARATION Surfaces should be dry, clean, free from standing water, grease, curing compounds,
    mould oils and all loosely adhering particles. Cement laitance should be removed by
    mechanical means. Rotary percussive drilling will help in providing a rough internal
    surface which will help in better bonding.

    CC/NG11/Ver7/07/12 1/3 Technical Datasheet


    Construction Chemicals

    NanoGrout SG

    MIXING Stir base and hardener individually before mixing. Add hardener to base component.
    Mix together thoroughly with a slow speed drill (max 400 R.P.M.) fitted with a paddle for
    one minute till a uniform colour and consistency is obtained.

    APPLICATION For Anchor Bolts


    Anchor bolt pockets, dowel and starter bar holes must be dry. Pour the mixed grout into
    the bolt hole and push the bolt/dowell bar into the hole with a slight agitation to remove
    entrapped air.

    For Patching Work and as Adhesive


    Apply the material by using notch trowel, scrapper or with a big spatula for a minimum
    thickness of 1 mm. Bonding of elements should be done while NanoGrout SG is still
    tacky.

    Volume of NanoGrout SG in ml/100mm. bond length

    Hole Diameter Bolt Diameter

    (mm.) 12 16 20 25 32 40

    20 25

    25 50 40 25

    32 80 70 60 40

    38 130 100 75 45

    45 150 130 100 45

    50 180 150 90

    62 280 225

    PACK SIZE 1Itr, 3 Itr and 6 Itr set

    GENERAL INFORMATION Shelf Life 12 months from date of manufacture when stored under
    warehouse conditions in original unopened packing. Extreme
    temperature / humidity may reduce shelf life.
    Cleaning Clean all equipments and tools with Conmix Cleaner immediately
    after use.

    HEALTH and SAFETY PPE's Gloves, goggles and suitable mask must be worn.

    CC/NG11/Ver7/07/12 2/3 Technical Datasheet


    Construction Chemicals

    NanoGrout SG

    Precautions Contact with skin, eyes, etc. must be avoided. If swallowed


    seek medical attention immediately.
    Hazard Regarded as non-hazardous for transportation.
    Disposal Do not reuse containers. To be disposed off as per local
    rules and regulations.
    Additional lnformation Refer MSDS. (Available on request.)

    TECHNICAL SERVICE CONMIX Technical Services are available on request for onsite support to assist in the
    correct use of its products.

    Manufacturer:
    CONMIX LTD.
    P.O. Box 5936, Sharjah
    United Arab Emirates Sales Office:
    Tel: +971 6 5314155 Tel: +971 6 5682422
    Fax: +971 6 5314332 Fax: +971 6 5681442
    Email: [email protected] www.conmix.com

    It is the customer’s responsibility to satisfy themselves by checking with the company whether information is still current at the time of use. The customer must be satisfied that the
    product is suitable for the use intended. All products comply with the properties shown on current data sheets. However, Conmix does not warrant or guarantee the installation of the
    products as it does not have any control over installation or end use of the product. All information and particularly the recommendations relating to application and end use are given in
    good faith. The products are guaranteed against any manufacturing defects and are sold subject to Conmix standard terms and conditions of sale.

    CC/NG11/Ver7/07/12 3/3 Technical Datasheet

    You might also like