Scribd Logo
Upload

Welcome to Scribd!

  • 267 views

    Atlas Drill Press Hi Lo Speed Attachment 5817

    Uploaded by

    Theodor Eike
    gearbox

    Copyright:

    © All Rights Reserved
    Download as PDF or read online from Scribd

    Atlas Drill Press Hi Lo Speed Attachment 5817

    Uploaded by

    Theodor Eike
    267 views2 pages
    gearbox

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    gearbox

    Copyright:

    © All Rights Reserved
    Download as PDF or read online from Scribd
    Download as pdf
    267 views2 pages

    Atlas Drill Press Hi Lo Speed Attachment 5817

    Uploaded by

    Theodor Eike
    gearbox

    Copyright:

    © All Rights Reserved
    Download as PDF or read online from Scribd
    Download as pdf
    of 2
    THSTRUCTIONS AND PARTS LIST FoR Nos. wi2l And Wi22 HI-LO | ATTACHMENT sulletin wazi-1 Apetly 1953 ATLAS PRESS COMPANY KALAMAZOO, MICHIGAN, U.S. A, MOUNTING INSTRUCTIONS Nos.W121 and W122 HI-LO SPEED ATTACHMENTS pulley to allgn belt horizontally, slid i i | Two belts are packed motor back until belt is tight = belt should i in carton with at- have just enough tension to prevent siip= tachment = be sure Pings Lock In position with the motor mount to remove them be Tock scre fore carton is di ee for mounting Hi-Lo... The pulley bearing should be lubricated period- ically, depending upon use -once a month for once every six months for occaslon= Lubricate through hole in pulley ing plate == use S.AsEs Nos 20 machine oil. LUBRICATION 1s To prepare drill pre: (a) Remove belt by loosening motor mount lock screws and sliding motor forward. (b) Invert motor pulley =» large step should be towards motor, see Figure |. SPINDLE SPEEDS (¢) Remove cap from top of column (not fur~ ished on some models). Spindle speeds in RPM are listed in chart below. Pulley steps are numbered to indi- cate position of belts to obtain speed de- sired. For example: To obtain a spindle speed of 210 RPM, place spindle belt in po- sition 4 and motor belt in position 1. (4) Position drill press head flush with top of column. BELT POSITIONS Lr anue sone waren | SPINDLE eM att Figsl~ Hilo attachnent mounted on Orit1 Press. seu} eel t * 210 ie |ieoee| Yow insert Hi-Lo In top of column. - 5 a eee lace Hi-Lo spindle belt around spindle 2 * ao pulley and Histo pulle 2 3 a8 = For Nos W122 Hi-Lo, use belt wi5=6 z 760 = For Now WI2I Hi-Lo, use either belt, they = = are both the sane size. 3 = 80 3 z 3,500 WAdjust Hi-Lo until belt is tight = bert 7 5 aaa should have Just enough tension to prevent slipping. Lock in position with aut on top ¥ 3 3,610 of Hi-Lo bracket. 7 z 6,850 ¥ z 15,200" 5: Place motor belt around Hi-Lo and motor pul cian Speed igo fast ~ sot recomended for @rili leys. If neces ry, adjust motor, or motor ‘Bperattons REPAIR PARTS FOR No. W122 HI-LO SPEED ATTACHMENT Mee ayateie ge vgs mu \ ane ep ystea0 1/48 REPAIR PARTS FOR No. W121 HI-LO SPEED ATTACHMENT ee pa sit “® y] re ay” \) ao Oe Ya" vateia nex a 4 SfO- fl FUSS ATLAS PRESS COMPANY «| KALAMAZOO MICHIGAN U.S.A. a aa Si

    You might also like