Scribd
Upload
196 views1 page

TTP Quick Reference Chart PDF

This document provides a quick reference guide for sublimation heat press settings for various substrates. It lists the recommended press time, temperature, and pressure for surfaces like polyester materials, vapor apparel, polyester/mouse pads, metals, unisub products, FR plastics, ceramics/mugs, and ceramic & glass tiles. The guide stresses that these are starting points and manufacturers' recommendations should always be followed to produce quality results, as settings can vary depending on specific materials. Proper pre-pressing, tack spraying, blow-out sheets, and removal of coatings are also noted as important for best outcomes.

Uploaded by

Ante Simic
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
196 views1 page

TTP Quick Reference Chart PDF

This document provides a quick reference guide for sublimation heat press settings for various substrates. It lists the recommended press time, temperature, and pressure for surfaces like polyester materials, vapor apparel, polyester/mouse pads, metals, unisub products, FR plastics, ceramics/mugs, and ceramic & glass tiles. The guide stresses that these are starting points and manufacturers' recommendations should always be followed to produce quality results, as settings can vary depending on specific materials. Proper pre-pressing, tack spraying, blow-out sheets, and removal of coatings are also noted as important for best outcomes.

Uploaded by

Ante Simic
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

SUBLIMATION HEAT PRESS SETTINGS - QUICK REFERENCE GUIDE

The following chart should serve only as a starti ng place. Producing quality end products is a matter of
suitable substrates, a calibrated heat press, smart color management, following manufacturer guidelines,
testing and practice!
If you are having difficulty or the substrate is not listed below, contact your reseller or the substrate
manufacturer for their specific recommendations.

SURFACE PRESS TIME TEMP PRESSURE TIPS/COMMENTS

POLYESTER 35-40 seconds 400° F 40 psi Pre-press shirt for 3-5 seconds to
MATERIAL (medium) eliminate moisture. Tack spray
transfer and use blow-out sheet to
avoid ghosting.

VAPOR APPAREL 45-55 seconds 380 - 40 psi See www.vaporapparel.com for tips
390° F (medium) on reducing press lines.

POLYESTER / 45 seconds 400° F 40 psi Look for a tight knit and high white
MOUSE PADS (medium) point for more brilliant color.

METAL (Unisub) 60 seconds 400° F 40 psi Use blow-out paper. Remove plastic
(medium) coating before pressing.

METAL (Other) - 60 seconds 375° - 40 psi Time varies with metal


White, Silver, 400° F (medium) manufacturer (always consult
Bronze manufacturer for correct time and
temp). Place absorbent sheet on
bottom of heat press. Then, place
product transfer side DOWN on top
of the absorbent sheet.

UNISUB 60 seconds 400° F 40 psi Remove plastic coating. Tear


PRODUCTS (medium) transfer paper away immediately
after pressing.

FR PLASTICS 60 - 75 seconds 400° F 40 psi Remove plastic coating. Tear


(medium) transfer paper away immediately
after pressing.

CERAMICS / MUGS 150 - 210 seconds 350° - 40 psi Time varies with press. Press into
400° F (medium) silicon pad. Mugs should be cooled
down after transfer paper is
removed in either a bucket of warm
water or using a cooling plate.

CERAMIC & 300 - 720 seconds 400° F 40 psi Time varies depending on tile type
GLASS TILES (medium) and size. Always consult
manufacturer. Press tiles from back
(transfer side down). Press into
silicon pad.

You might also like