Wave Springs CC2015

Wave Spring Introduction
All Springs Are Product Performance

Not Equal® With their smooth, circular coiled sinusoidal wave form,
and rolled round edges of pre-tempered raw material,
Smalley Wave Springs offer the unique advantage of space Smalley’s edgewound Wave Springs offer many advantages
savings when used to replace coil springs. By reducing over die stamped products.
spring o
perating height, wave springs also produce a
Loads and spring rates are more accurate, more
decrease in the spring cavity. With a smaller assembly size
predictable, and may be toleranced better than 50 percent
and less material used in the manufacturing process, a cost
tighter than stampings. The force of a Smalley Wave Spring
savings is realized.
will increase at a uniform rate throughout most of its
Wave springs operate as load bearing devices. They available deflection.
take up play and compensate for dimensional variations
By any criteria, Smalley Wave Springs offer their users
within assemblies. A v irtually unlimited range of forces
higher dependability and better performance. Since
can be produced whereby loads build either gradually
they are produced from full hard, pre-tempered raw
or abruptly to reach a predetermined working height.
material, there is no risk of distorting the spring during
This establishes a precise spring rate in which load is
a hardening heat treatment. By contrast, subsequent
proportional to deflection.
manufacturing procedures for stamped wavy washers
Functional requirements are necessary for both dynamic can lead to problems such as fatigue cracking and
and static spring applications. Special performance inaccurate or inconsistent loading between springs.
characteristics are individually built into each spring to All told, the metallurgy, the mechanical properties and
satisfy a variety of precise operating conditions. Typically, the uniform dimensional stability of the Smalley
a wave spring will occupy an extremely small area for the edgewound Wave Spring provide a component for
amount of work it performs. The use of this product is precision quality applications.
demanded, but not limited to tight axial and radial
space constraints.
SMALLEY WAVE SPRING COIL SPRING
10 smalley.com No-Tooling-Charges™ For Customs

Wave Spring Types

Gap & Overlap Type
Conventional Gap and Overlap Type Wave Springs are used in a wide variety of
applications. For short deflections and low-medium forces, they function with precision
and dependability.
Gap Type These two types of Smalley Wave Springs permit radial expansion or growth in diameter
Wave Spring within a cavity, without the binding or hang-up normally associated with die stamped
wave washers. Just as their terms imply, the gap type is split to retain a gap between
the ends, while the overlap type has overlapping ends. Thus, the ends are free to move
circumferentially as the spring outside diameter grows during compression.
For example, the O.D. of a Gap Type Wave Spring would fit .020 loose per side in a bore.
Its I.D. clears a shaft by .010 per side. As the spring is deflected, the O.D. and I.D. grow
larger until the O.D. contacts the bore. Continued deflection causes the gap ends to
move closer together while the O.D. presses against the bore. An Overlap Type Wave
Overlap Type
Spring permits this type of cycling action in a similar manner.
Wave Spring
Crest-to-Crest®
Crest-to-Crest Wave Springs are prestacked in series, decreasing the spring rate
proportionally to the number of turns. Uses are typically applications requiring
low-medium spring rates and large deflections with low-medium forces. Among
major advantages, this design eliminates the need to keep the wave crests aligned.
The need to use a key locating device, or to insert a shim between individual springs
is not necessary. Because the spring is integrally formed, the wave peaks hold
their configuration.
As a replacement for helical compression springs, Crest-to-Crest springs can develop

similar forces, yet occupy one-half (1⁄2) or less the axial space. This allows for strict
space constraints. Crest-to-Crest Wave Springs will maintain the same force and load
specifications of a conventional round wire spring, but with the advantages of resultant
lowered and compacted operating heights, free heights, and solid heights.
continued
Manufactured in USA Smalley (847) 719-5900 11

Wave Spring Types (cont’d)

Crest-to-Crest with Optional Shim Ends
Crest-to-Crest Wave Springs are also available with squared-shim ends. S him ends
provide a 360˚ contact surface when compared to the wave point contact of plain ends.
The shim-ends, under load, more evenly distribute the spring’s force upon adjacent
components. This feature is similar to the concept of double-disc grinding springs for a
flat surface. Shim ends have also been used to affix springs to mating components, as a
flat locating s urface that may be attached by various methods in the assembly.
Nested
Nested Wave Springs are pre-stacked in parallel from one continuous filament of flat
wire. The need to stack individual springs for higher loads is no longer necessary. Nested
springs result in a spring rate that increases proportionally to the number of turns. They
can exert tremendous forces, yet maintain the precision of a circular-grain wave spring.
In many a pplications, Nested Wave Springs replace Belleville Springs, particularly in
cases where a high but accurate force is needed.
WAVO®
Wavo Springs are produced from round-section wire to provide higher loads while
maintaining the accurate loading found in wave springs. As an alternative to Belleville
Springs, the Wavo provides similar loads but with an accurate, predictable spring rate.
Linear Springs
Linear springs are a continuous wave formed (marcelled) wire length produce from
spring tempered materials. They act as a load bearing device having approximately the
same load/deflection characteristics as a wave spring.
Forces act linearly or radially depending on the installed position. Axial pressure
is obtained by laying the spring flat in a straight line. Circular wrapping the spring
produces a radial force or outward pressure. Linear springs are available cut to length
or as a continuous coil, for the user to cut as needed.
Request FREE samples Get CAD downloads

Get free samples of any Simplify your design process by
standard catalog item at downloading CAD models of standard
www.smalley.com/samples. retaining rings and wave springs at
www.smalley.com/cad-models.
Or use form on page 131 of
this catalog. Requests typically
processed within 24 hours.

Wave Spring Applications
B. Face Seal
A. Pressure Relief Valve
C. Clutch Drive
D. Bayonet Connector
E. Multi-Tooth Cutter
A. Pressure Relief Valve B. Face Seal C. Clutch Drive D. Bayonet Connector E. Multi-Tooth Cutter
An exact load applied to Wave Spring applies Pressure on the round belt Overlap Type Wave Spring A custom designed wave
the top sealing plate was pressure, to precisely load is produced by compressing installed in an electronic spring with locating tabs is
accomplished using a the carbon face against a the Wavo Spring through connector assembly. As male contained in the housing.
flat wire wave spring. Air mating surface, to properly the sheave halves. The and female components are The spring applies a precise
pressure entering the top seal fluids. The spring top threaded cap rotates rotated together into final force to the two cutter
slots forces the plate away operates over a fixed to adjust the Wavo assembly, the wave spring is halves, allowing them to
from the sealing surface working range and provides compression. The Wavo can compressed to its working oscillate but not rattle.
providing the pressure relief an exact force, unlike the produce a high force in a height. In this position it
mechanism. stamped wavy washer it tight radial cavity. exerts a constant force
replaced which could not that locks both
maintain the necessary components together.
spring rate.

F. Slip Clutch
G. Bearing Pre-Load
H. Flow Valve
J. Sprinkler Valve
I. Low Voltage Connector
F. Slip Clutch G. Bearing Pre-Load H. Flow Valve I. Low Voltage J. Sprinkler Valve
Clutch drives when the One of the most common As fluid pressure increases Connector With height restrictions
“V”-detents are in the wave spring applications the Crest-to-Crest Wave A Bayonet Connector accounted for, the Smalley
“V”-slots. A Smalley Wave world-wide is a bearing Spring precisely controls the couples as the male end Crest-to-Crest Wave Spring
Spring maintains pressure to preload arrangement as linear displacement of the rotates and follows the maintains constant pressure
hold this position. As torque illustrated. Having the piston, which positions the groove contour in the on the pop-up head, holding
is increased, the “V”-detents proper load will often extend orifice for proper fluid flow. female end. A 2-Turn Nested it firmly closed. In operation,
will ride up and out the bearing life by lowering Because of the space savings Spirawave Wave Spring water pressure releases
“V”-slots, depressing the operating temperatures, of the Crest-to-Crest provides the pre-load the head by overcoming
wave spring and developing reducing vibration, design, the valve can be between the two halves. the spring’s force.
the slip mechanism. When minimizing wear and made smaller. A 2-Turn Nested Spring
torque is decreased, the providing for quieter and was necessary to develop
wave spring forces the smoother performance. a higher load in very tight
“V”-detents firmly into the radial and axial space.
“V”-slots to drive again.

K. Oil Valve
L. Ball Valve
M. Quick Disconnect
N. Vibration Isolator
O. Floating Gear
K. Oil Valve L. Ball Valve M. Quick Disconnect N. Vibration Isolator O. Floating Gear
The force provided by the A Smalley Crest-to-Crest The sliding member of Wavo Springs provide Functioning in a contained
Crest-to-Crest Wave Spring Wave Spring is used to the disconnect is held in its high force and a relatively bracket, a Crest-to-Crest
in this oil valve application reduce the overall spring forward/locked position large axial displacement, in Wave Spring loads a gear
precisely regulates the height in this application. against the retaining ring, by limited space. The springs with light force allowing axial
amount of oil that is released. The wave spring allows the Crest-to-Crest Spring. As are arranged in series for movement. The gear shown
The Crest-to-Crest spring the seat to oscillate on the the user slides the member additional travel. self-aligns with its mating
provides accurate resistance ball, keeping a tight seal in in the opposite direction gear during operation.
in a small space, allowing the the operating position. The compressing the spring,
overall size of the valve to be reduction in spring height the detent balls align with a
greatly reduced. and resulting smaller spring groove and release.
cavity also reduce the weight
of the valve.

SSR Series - Standard Section Springs
Stock Items in carbon steel and 17-7 PH stainless steel. Springs listed below are 3 wave, Overlap Type.
Smalley Part Operates in Clears Shaft Load Work Free Number Radial Spring
Number 1, 4 Bore Diameter Diameter (lb) Height Height 2 of Waves Thickness Wall Rate 3
SSR-0050 .500 .390 7 .050 .085 3 .008 .040 200
SSR-0062 .625 .480 10 .050 .095 3 .010 .058 222
SSR-0075 .750 .500 14 .062 .160 3 .010 .078 143
SSR-0087 .875 .620 16 .062 .130 3 .012 .094 235
SSR-0100 1.000 .780 18 .062 .160 3 .012 .094 184
SSR-0112 1.125 .840 20 .078 .130 3 .016 .133 385
SSR-0125 1.250 .960 22 .078 .150 3 .016 .133 306
SSR-0137 1.375 1.090 24 .078 .190 3 .016 .133 214
SSR-0150 1.500 1.170 26 .078 .170 3 .018 .143 283
SSR-0162 1.625 1.310 28 .078 .200 3 .018 .143 230
1
Add suffix “-S17” for 17-7 stainless steel.
2
Reference dimension.
3
Theoretical dimension; measured in lb/in.
4
See pages 132-133 for How to Order.
Get CAD downloads

Simplify your design process by downloading CAD models of standard
retaining rings and wave springs at www.smalley.com/cad-models.
OVERLAP TYPE
SSR-0050 to SSR-0162
Product Dimensions
All dimensions in inches
unless otherwise specified.
3 WAVE
RADIAL
WALL
THICKNESS FREE
HEIGHT
CLEARS SHAFT
LOAD AT
Bayonet Connector
DIAMETER
WORK HEIGHT
OPERATES IN BORE
DIAMETER

SSR Series
Stock Items in carbon steel and 17-7 PH stainless steel. Springs listed below are 4 waves and up, Gap Type.
SSR-0175 1.750 1.440 30 .078 .140 4 .018 .143 484
SSR-0187 1.875 1.560 32 .078 .150 4 .018 .143 444
SSR-0200 2.000 1.680 34 .093 .140 4 .024 .150 723
SSR-0212 2.125 1.800 36 .093 .150 4 .024 .150 632
SSR-0225 2.250 1.930 38 .093 .170 4 .024 .150 494
SSR-0237 2.375 1.990 40 .093 .160 4 .024 .178 597
SSR-0250 2.500 2.120 42 .093 .170 4 .024 .178 545
SSR-0262 2.625 2.240 44 .093 .190 4 .024 .178 454
SSR-0275 2.750 2.340 46 .109 .170 4 .030 .188 754
SSR-0287 2.875 2.470 48 .109 .180 4 .030 .188 676
SSR-0300 3.000 2.590 50 .109 .190 4 .030 .188 617
SSR-0312 3.125 2.710 52 .109 .210 4 .030 .188 515
SSR-0325 3.250 2.750 54 .109 .200 4 .030 .233 593
SSR-0337 3.375 2.840 56 .109 .220 4 .030 .233 505
SSR-0350 3.500 3.000 58 .109 .230 4 .030 .233 479
SSR-0362 3.625 3.120 60 .109 .240 4 .030 .233 458
SSR-0375 3.750 3.250 62 .109 .260 4 .030 .233 411
SSR-0387 3.875 3.370 64 .109 .300 4 .030 .233 335
SSR-0400 4.000 3.500 66 .109 .190 5 .030 .233 815
SSR-0412 4.125 3.620 67 .109 .200 5 .030 .233 736
SSR-0425 4.250 3.740 69 .109 .210 5 .030 .233 683
SSR-0437 4.375 3.860 70 .109 .210 5 .030 .233 693
SSR-0450 4.500 3.990 72 .109 .230 5 .030 .233 595 GAP TYPE
SSR-0462 4.625 4.110 73 .125 .270 5 .030 .233 503
SSR-0475 4.750 4.240 75 .125 .310 5 .030 .233 405 SSR-0175 to SSR-1600
SSR-0487 4.875 4.370 76 .125 .290 5 .030 .233 461
SSR-0500 5.000 4.490 78 .125 .310 5 .030 .233 422
SSR-0512 5.125 4.610 80 .125 .340 5 .030 .233 372 Product Dimensions
SSR-0525 5.250 4.740 82 .125 .370 5 .030 .233 335 All dimensions in inches
SSR-0537 5.375 4.860 84 .125 .380 5 .030 .233 329 unless otherwise specified.
SSR-0550 5.500 4.990 86 .125 .250 6 .030 .233 688
SSR-0562 5.625 5.110 88 .125 .270 6 .030 .233 607 MULTI-WAVE
SSR-0575 5.750 5.240 90 .125 .280 6 .030 .233 581 (SEE TABLE)
SSR-0587 5.875 5.360 92 .125 .300 6 .030 .233 526
SSR-0600 6.000 5.490 94 .125 .300 6 .030 .233 537
SSR-0612 6.125 5.610 96 .125 .310 6 .030 .233 519
SSR-0625 6.250 5.730 98 .125 .340 6 .030 .233 456 RADIAL
WALL
SSR-0637 6.375 5.860 100 .125 .350 6 .030 .233 444
SSR-0650 6.500 5.980 102 .125 .390 6 .030 .233 385
SSR-0675 6.750 6.230 104 .125 .420 6 .030 .233 353
SSR-0700 7.000 6.160 106 .156 .320 6 .032 .375 646
SSR-0725 7.250 6.440 108 .156 .350 6 .032 .375 557
SSR-0750 7.500 6.690 110 .156 .360 6 .032 .375 539
SSR-0775 7.750 6.940 114 .156 .380 6 .032 .375 509
SSR-0800 8.000 7.190 118 .156 .390 6 .032 .375 504
SSR-0825 8.250 7.440 122 .156 .430 6 .032 .375 445 FREE
THICKNESS HEIGH T
SSR-0850 8.500 7.680 126 .156 .340 7 .032 .375 685
SSR-0875 8.750 7.930 130 .156 .340 7 .032 .375 707
SSR-0900 9.000 8.180 134 .156 .290 8 .032 .375 1,000
SSR-0950 9.500 8.680 142 .156 .240 9 .032 .375 1,690
SSR-1000 10.000 9.170 150 .156 .290 9 .032 .375 1,119 CLEARS SHAFT LOAD AT
DIAMETER WORK HEIGHT
SSR-1050 10.500 9.670 158 .156 .310 9 .032 .375 1,026
SSR-1100 11.000 10.170 166 .156 .350 9 .032 .375 856 OPERATES IN BORE
SSR-1150 11.500 10.660 174 .156 .360 9 .032 .375 853 DIAMETER
SSR-1200 12.000 11.160 182 .156 .440 9 .032 .375 641
SSR-1250 12.500 11.660 190 .156 .350 10 .032 .375 979
SSR-1300 13.000 12.160 198 .156 .410 10 .032 .375 780
SSR-1350 13.500 12.650 206 .156 .430 10 .032 .375 752
SSR-1400 14.000 13.150 214 .156 .300 12 .032 .375 1,486
SSR-1450 14.500 13.650 221 .156 .320 12 .032 .375 1,348
SSR-1500 15.000 14.130 230 .156 .350 12 .032 .375 1,186
SSR-1550 15.500 14.640 239 .156 .310 13 .032 .375 1,552
SSR-1600 16.000 15.140 248 .156 .340 13 .032 .375 1,348
1
2
3
4

SSR-N Series - Narrow Section Wave Springs
Smalley narrow section wave springs were originally designed to pre-load packings in telescoping hydraulic cylinders. They have also
found other applications where working space is highly limited. This Smalley Wave Spring series is designed to fit into a bore with a light
snap to assure perfect concentricity between the wave spring and assembly. When these narrow section wave springs are compressed,
radial expansion is taken up by the gap in the spring to eliminate binding.
SSR-0325-N 3.250 2.820 54 .109 .200 4 .030 .188 593
SSR-0337-N 3.375 2.940 56 .109 .220 4 .030 .188 505
SSR-0350-N 3.500 3.070 58 .109 .260 4 .030 .188 384
SSR-0362-N 3.625 3.190 60 .109 .270 4 .030 .188 373
SSR-0375-N 3.750 3.320 62 .109 .280 4 .030 .188 363
SSR-0387-N 3.875 3.440 64 .109 .310 4 .030 .188 318
SSR-0400-N 4.000 3.570 66 .109 .200 5 .030 .188 725
SSR-0412-N 4.125 3.690 67 .109 .200 5 .030 .188 736
SSR-0425-N 4.250 3.820 69 .109 .240 5 .030 .188 527
SSR-0437-N 4.375 3.940 70 .109 .210 5 .030 .188 693
SSR-0450-N 4.500 4.070 72 .109 .280 5 .030 .188 421
SSR-0462-N 4.625 4.190 73 .125 .270 5 .030 .188 503
SSR-0475-N 4.750 4.320 75 .125 .320 5 .030 .188 385
SSR-0487-N 4.875 4.440 76 .125 .320 5 .030 .188 390
SSR-0500-N 5.000 4.570 78 .125 .350 5 .030 .188 347
SSR-0512-N 5.125 4.690 80 .125 .350 5 .030 .188 356
SSR-0525-N 5.250 4.820 82 .125 .360 5 .030 .188 349
GAP TYPE SSR-0537-N 5.375 4.940 84 .125 .440 5 .030 .188 267
SSR-0550-N 5.500 5.070 86 .125 .280 6 .030 .188 555
SSR-0325-N to SSR-0775-N SSR-0562-N 5.625 5.190 88 .125 .290 6 .030 .188 533
SSR-0575-N 5.750 5.320 90 .125 .340 6 .030 .188 419
SSR-0587-N 5.875 5.440 92 .125 .340 6 .030 .188 428
Product Dimensions SSR-0600-N 6.000 5.570 94 .125 .340 6 .030 .188 437
All dimensions in inches SSR-0612-N 6.125 5.690 96 .125 .280 7 .030 .188 619
unless otherwise specified. SSR-0625-N 6.250 5.820 98 .125 .280 7 .030 .188 632
SSR-0637-N 6.375 5.940 100 .125 .300 7 .030 .188 571
SSR-0650-N 6.500 6.070 102 .125 .300 7 .030 .188 583
MULTI-WAVE SSR-0675-N 6.750 6.320 104 .125 .300 7 .030 .188 594
(SEE TABLE) SSR-0700-N 7.000 6.480 106 .156 .320 7 .030 .233 646
SSR-0725-N 7.250 6.730 108 .156 .330 7 .030 .233 621
SSR-0750-N 7.500 6.980 110 .156 .360 7 .030 .233 539
SSR-0775-N 7.750 7.230 114 .156 .380 7 .030 .233 509
RADIAL
WALL
1
2
3
4
FREE
THICKNESS HEIGHT
Request FREE samples

CLEARS SHAFT LOAD AT Get free samples of any standard catalog item at www.smalley.com/samples.
OPERATES IN BORE Or use form on page 131 of this catalog. Requests typically processed within
DIAMETER
24 hours.

WAVO® Series
Stock Items in carbon and 17-7 PH stainless steel.
Smalley Part Operates in Clears Shaft Load Work Free Number Wire Spring
Number 1, 4 Bore Diameter Diameter (lb) Height Height 2 of Waves Diameter Rate 3
RW-0050 .500 .408 35 .052 .062 3 .031 3,500
RW-0062 .625 .517 50 .064 .077 3 .038 3,846
RW-0075 .750 .628 70 .076 .092 3 .045 4,375
RW-0087 .875 .740 80 .086 .104 3 .051 4,444
RW-0100 1.000 .855 90 .095 .116 3 .056 4,286
RW-0112 1.125 .967 100 .102 .127 3 .060 4,000
RW-0125 1.250 1.081 110 .110 .138 3 .065 3,929
RW-0137 1.375 1.223 120 .095 .121 4 .056 4,615
RW-0150 1.500 1.339 130 .102 .128 4 .060 5,000
RW-0162 1.625 1.444 140 .110 .137 4 .065 5,185
RW-0175 1.750 1.564 150 .113 .144 4 .067 4,839
RW-0187 1.875 1.682 160 .119 .155 4 .070 4,444
RW-0200 2.000 1.803 170 .124 .165 4 .072 4,146
RW-0212 2.125 1.906 180 .129 .162 4 .076 5,455
RW-0225 2.250 2.023 190 .136 .168 4 .080 5,938
RW-0237 2.375 2.141 200 .141 .178 4 .083 5,405
RW-0250 2.500 2.261 210 .144 .185 4 .085 5,122
RW-0262 2.625 2.374 220 .153 .203 4 .090 4,400
RW-0275 2.750 2.497 230 .154 .212 4 .091 3,966
RW-0287 2.875 2.618 240 .158 .210 4 .093 4,615
RW-0300 3.000 2.767 250 .141 .179 5 .083 6,579
RW-0312 3.125 2.878 260 .144 .184 5 .085 6,500
RW-0325 3.250 2.992 270 .153 .190 5 .090 7,297
RW-0337 3.375 3.115 280 .154 .195 5 .091 6,829
RW-0350 3.500 3.236 290 .158 .201 5 .093 6,744
RW-0362 3.625 3.356 300 .161 .206 5 .095 6,667
RW-0375 3.750 3.475 310 .166 .212 5 .098 6,739
RW-0387 3.875 3.595 320 .170 .208 5 .100 8,421 Product Dimensions
RW-0400 4.000 3.718 330 .170 .225 5 .100 6,000 All dimensions in inches
RW-0412 4.125 3.827 335 .175 .221 5 .105 7,283 unless otherwise specified.
RW-0425 4.250 3.948 345 .178 .225 5 .105 7,340
RW-0437 4.375 4.063 350 .187 .240 5 .110 6,604
MULTI-WAVE
RW-0450 4.500 4.185 360 .187 .247 5 .110 6,000 (SEE TABLE)
RW-0462 4.625 4.310 365 .187 .253 5 .110 5,530
RW-0475 4.750 4.431 375 .190 .257 5 .112 5,597
RW-0487 4.875 4.555 380 .190 .264 5 .112 5,135
RW-0500 5.000 4.672 390 .195 .265 5 .116 5,571
RW-0512 5.125 4.772 400 .200 .274 5 .118 5,405
RW-0525 5.250 4.893 410 .204 .279 5 .120 5,467
RW-0537 5.375 5.037 420 .187 .245 6 .110 7,241
RW-0550 5.500 5.162 430 .187 .251 6 .110 6,719
RW-0562 5.625 5.283 440 .190 .245 6 .112 8,000
RW-0575 5.750 5.406 450 .190 .251 6 .112 7,377 WIRE
DIAMETER
RW-0587 5.875 5.524 460 .197 .262 6 .116 7,077
RW-0600 6.000 5.644 470 .200 .268 6 .118 6,912
FREE
1
Add suffix “-S17” for 17-7 stainless steel. HEIGHT
2
3
4
CLEARS SHAFT LOAD AT
OPERATES IN BORE
DIAMETER
Get CAD downloads

Simplify your design process by downloading CAD models of standard
retaining rings and wave springs at www.smalley.com/cad-models.

SSB Series - Metric Bearing Preload Springs
Smalley Circular-Grain bearing preload Wave Springs eliminate play and minimize bearing noise. The constant light/medium pressure they
apply removes play between the ball bearings and the bearings’ inner and outer races. Preloading can reduce the possibility of bearing
damage due to vibration (vibratory loading) and wear due to repetitive and non-repetitive runout.
Stock Items in carbon steel and 17-7 PH stainless steel. Springs listed below are 3 and 4 waves Overlap Type.
Smalley Part Bearing O.D. 2 Clears Shaft Load Work Free Number Radial Spring
Number 1, 5 (mm) Diameter (N) Height Height 3 of Waves Thickness Wall Rate 4
SSB-0063 16.00 11.28 44.5 1.57 2.29 3 .25 1.98 65
SSB-0075 19.00 14.28 53.4 1.57 3.05 3 .25 1.98 35
SSB-0087 22.00 16.46 62.3 1.57 2.79 3 .30 2.39 48
SSB-0095 24.00 18.46 66.7 1.57 3.56 3 .30 2.39 35
SSB-0102 26.00 18.22 71.2 1.98 2.54 3 .41 3.38 111
SSB-0110 28.00 20.22 75.6 1.98 2.79 3 .41 3.38 85
SSB-0118 30.00 22.22 84.5 1.98 3.30 3 .41 3.38 66
SSB-0126 32.00 24.22 89.0 1.98 3.81 3 .41 3.38 52
SSB-0138 35.00 27.22 97.9 1.98 4.57 3 .41 3.38 38
SSB-0146 37.00 28.72 102.3 1.98 3.81 3 .46 3.63 58
SSB-0158 40.00 31.72 111.2 1.98 5.08 3 .46 3.63 37
SSB-0165 42.00 33.72 115.7 1.98 3.05 4 .46 3.63 99
SSB-0185 47.00 38.72 129.0 1.98 3.81 4 .46 3.63 68
OVERLAP TYPE SSB-0205
SSB-0217
52.00
55.00
43.11 142.4 2.36
46.11 151.3 2.36
3.56
3.81
4
4
.61
.61
3.76 121
3.76 100
SSB-0063 to SSB-0374 SSB-0244 62.00 51.69 169.1 2.36 4.32 4 .61 4.52 85
SSB-0268 68.00 57.17 186.9 2.77 4.32 4 .76 4.78 131
SSB-0276 70.00 59.17 191.3 2.77 4.32 4 .76 4.78 119
Product Dimensions SSB-0284 72.00 61.17 195.8 2.77 4.57 4 .76 4.78 108
SSB-0295 75.00 64.17 204.7 2.77 5.08 4 .76 4.78 94
All dimensions in millimeters
SSB-0315 80.00 68.66 218.0 2.77 5.59 4 .76 4.78 76
SSB-0335 85.00 71.38 231.4 2.77 5.59 4 .76 5.92 83
SSB-0354 90.00 76.38 249.2 2.77 6.35 4 .76 5.92 68
SSB-0374 95.00 81.38 262.5 2.77 7.37 4 .76 5.92 57
1
2
Wave springs fit snug in housing.
3
WAVE
4
Theoretical dimension; measured in N/mm.
SPRING
FITS SNUG
5
IN
HOUSING
MULTI-WAVE
(SEE TABLE)
Bearing Assembly
RADIAL
WALL
FREE
Request FREE samples
THICKNESS
Get free samples of any standard catalog item at www.smalley.com/samples.
HEIGHT
Or use form on page 131 of this catalog. Requests typically processed within
BEARING O.D.
LOAD AT 24 hours.
WORK HEIGHT

SSB Series
Smalley Part Bearing O.D. 2 Clears Shaft Load Work Free Number Radial Spring
Number 1, 5 (mm) Diameter (N) Height Height 3 of Waves Thickness Wall Rate 4
SSB-0394 100.00 86.38 275.9 2.77 4.57 5 .76 5.92 157
SSB-0413 105.00 91.38 289.2 2.77 5.08 5 .76 5.92 134
SSB-0433 110.00 96.38 302.6 2.77 5.33 5 .76 5.92 115
SSB-0453 115.00 101.38 315.9 3.18 6.35 5 .76 5.92 99
SSB-0472 120.00 106.38 329.3 3.18 7.11 5 .76 5.92 86
SSB-0492 125.00 111.38 342.6 3.18 7.62 5 .76 5.92 76
SSB-0512 130.00 116.38 356.0 3.18 8.64 5 .76 5.92 67
SSB-0532 135.00 121.38 369.3 3.18 9.40 5 .76 5.92 59
SSB-0551 140.00 126.38 382.7 3.18 6.86 6 .76 5.92 108
SSB-0571 145.00 131.38 396.0 3.18 7.37 6 .76 5.92 97
SSB-0591 150.00 136.38 404.9 3.18 7.87 6 .76 5.92 87
SSB-0630 160.00 146.38 440.5 3.18 9.40 6 .76 5.92 71
SSB-0650 165.00 151.38 453.9 3.18 10.41 6 .76 5.92 64
SSB-0669 170.00 156.38 467.2 3.18 11.18 6 .76 5.92 58
SSB-0689 175.00 154.16 480.6 3.96 8.13 6 .81 9.53 116
SSB-0709 180.00 159.16 493.9 3.96 8.64 6 .81 9.53 105
SSB-0728 185.00 164.16 507.3 3.96 9.14 6 .81 9.53 97
SSB-0748 190.00 169.16 520.6 3.96 9.91 6 .81 9.53 88 GAP TYPE
SSB-0787
SSB-0807
200.00
205.00
179.16 547.3 3.96
184.16 560.7 3.96
7.11
7.37
7
7
.81
.81
9.53 174
9.53 161
SSB-0394 to SSB-2284
SSB-0827 210.00 189.16 578.5 3.96 7.87 7 .81 9.53 149
SSB-0847 215.00 194.16 591.8 3.96 8.38 7 .81 9.53 138
SSB-0866 220.00 199.16 605.2 3.96 8.64 7 .81 9.53 128 Product Dimensions
SSB-0886 225.00 204.16 618.5 3.96 7.11 8 .81 9.53 203 All dimensions in millimeters
SSB-0906 230.00 209.16 631.9 3.96 6.10 9 .81 9.53 303 unless otherwise specified.
SSB-0925 235.00 214.16 645.2 3.96 6.35 9 .81 9.53 283
SSB-0945 240.00 219.16 658.6 3.96 6.35 9 .81 9.53 265
SSB-0984 250.00 229.16 685.3 3.96 6.86 9 .81 9.53 232
SSB-1024 260.00 239.16 712.0 3.96 7.37 9 .81 9.53 205
SSB-1043 265.00 244.16 725.3 3.96 7.62 9 .81 9.53 193
SSB-1063 270.00 249.16 743.1 3.96 8.13 9 .81 9.53 182
SSB-1102 280.00 259.16 769.8 3.96 8.64 9 .81 9.53 162
SSB-1142 290.00 269.16 796.5 3.96 9.40 9 .81 9.53 144 WAVE
SPRING
SSB-1181 300.00 279.16 823.2 3.96 10.41 9 .81 9.53 129 FITS SNUG
SSB-1221 310.00 289.16 849.9 3.96 7.11 9 1.07 9.53 264 IN
HOUSING
SSB-1260 320.00 299.16 876.6 3.96 7.62 9 1.07 9.53 239
SSB-1339 340.00 319.16 934.5 3.96 8.64 9 1.07 9.53 198
SSB-1378 350.00 329.16 961.1 3.96 9.40 9 1.07 9.53 180
SSB-1417 360.00 339.16 987.9 3.96 7.62 10 1.07 9.53 271
SSB-1457 370.00 349.16 1014.6 3.96 8.13 10 1.07 9.53 249
SSB-1496 380.00 359.16 1041.3 3.96 8.64 10 1.07 9.53 229
SSB-1535 390.00 369.16 1072.4 3.96 9.14 10 1.07 9.53 211
SSB-1575 400.00 379.16 1099.1 3.96 9.65 10 1.07 9.53 196
SSB-1614 410.00 382.82 1125.8 3.96 8.38 10 1.07 12.70 251 MULTI-WAVE
(SEE TABLE)
SSB-1654 420.00 392.82 1152.5 3.96 8.89 10 1.07 12.70 233
SSB-1693 430.00 402.82 1179.2 3.96 7.62 11 1.07 12.70 317
SSB-1732 440.00 412.82 1205.9 3.96 8.13 11 1.07 12.70 295
SSB-1811 460.00 432.82 1263.7 3.96 8.89 11 1.07 12.70 256 RADIAL
SSB-1890 480.00 452.82 1317.1 3.96 8.13 12 1.07 12.70 318 WALL
SSB-1969 500.00 472.82 1370.5 3.96 8.89 12 1.07 12.70 280
SSB-2126 540.00 512.82 1481.8 3.96 8.89 13 1.07 12.70 303
SSB-2284 580.00 552.82 1593.0 3.96 8.89 14 1.07 12.70 327
1
2
3
4
Theoretical dimension; measured in N/mm. FREE
THICKNESS HEIGHT
5
BEARING O.D. LOAD AT

WORK HEIGHT

Cross Reference Guide - SSB Bearing Table
What is Bearing Preload?

Ball bearings, composed of multiple parts working together as an assembly, are designed with clearances that
permit freedom of motion. Clearance is not necessarily a result of manufacturing precision – bearings may be
designed with greater clearance to accommodate higher axial loads or minor axial misalignment. As clearance
and manufacturing tolerances stack up, a bearing assembly will begin to experience axial and radial play.
Bearing Preload is the process of adding a sustained axial load, independent of external loads, to the bearing.
An axial preload ensures constant contact between the ball complement and bearing races reducing or
eliminating both modes of play. Spring Preload, a versatile execution of Bearing Preload, utilizes single turn
Wave Springs to add the necessary preload forces despite dimensional variation and thermal expansion.
Properly preloading a bearing can increase its life and eliminate the vibration and noise that results from
specified clearance, manufacturing precision, and wear.
Bearing without a preload: Clearance between Bearing with a preload: The ball complement
components can cause vibration and wear. and bearing races mate reliably reducing or
eliminating vibration and wear.
Use this cross-reference guide to select the appropriate Wave Spring for your bearing size. The numbers represent typical standard bearing
part numbers and/or the suffix of a standard bearing size.
Stock Items in carbon steel and 17-7 PH stainless steel.
Bearing Part Numbers

Smalley Part Bearing Extra Extremely Extra
Number 1, 4 O.D. 2 (mm) Small Light Light Narrow Light Medium Heavy
SSB-0063 16.00 34 — — — — — —
SSB-0075 19.00 35, 36 — — — — — —
SSB-0087 22.00 37, 38 00 — — — — —
SSB-0095 24.00 38KV 01 — — — — —
SSB-0102 26.00 39 — 100 — — — —
SSB-0110 28.00 — 02 101 — — — —
SSB-0118 30.00 — 03 — — 200 — —
SSB-0126 32.00 — — 102 02 201 — —
SSB-0138 35.00 — — 103 — 202 300 —
SSB-0146 37.00 — 04 — 03 — 301 —
SSB-0158 40.00 — — — — 203 — —
SSB-0165 42.00 — 05 104 04 — 302 —
SSB-0185 47.00 — 06 105 — 204 303 —
SSB-0205 52.00 — — — 05 205 304 —
SSB-0217 55.00 — 07 106 — — — —
SSB-0244 62.00 — 08 107 06 206 305 403
SSB-0268 68.00 — 09 108 — — — —
SSB-0276 70.00 — — — 07 — — —
SSB-0284 72.00 — 10 — — 207 306 404
SSB-0295 75.00 — — 109 — — — —

Cross Reference Guide
Use this cross-reference guide to select the appropriate Wave Spring for your bearing size. The numbers represent typical standard bearing
part numbers and/or the suffix of a standard bearing size.
Bearing Part Numbers

Smalley Part Bearing Extra Extremely Extra
Number 1, 4 O.D. 2 (mm) Small Light Light Narrow Light Medium Heavy
SSB-0315 80.00 — 11 110 08 208 307 405
SSB-0335 85.00 — 12 — 09 209 — —
SSB-0354 90.00 — 13 111 10 210 308 406
SSB-0374 95.00 — — 112 — — — —
SSB-0394 100.00 — 14 113 11 211 309 407
SSB-0413 105.00 — 15 — 12 — — —
SSB-0433 110.00 — 16 114 — 212 310 408
SSB-0453 115.00 — — 115 13 — — —
SSB-0472 120.00 — 17 — 14 213 311 409
SSB-0492 125.00 — 18 116 — 214 — —
SSB-0512 130.00 — 19 117 15 215 312 410
SSB-0532 135.00 — — — 16 — — —
SSB-0551 140.00 — 20 118 — 216 313 411
SSB-0571 145.00 — 21 119 17 — — —
SSB-0591 150.00 — 22 120 18 217 314 412
SSB-0630 160.00 — — 121 19 218 315 413
SSB-0650 165.00 — 24 — 20 — — —
SSB-0669 170.00 — — 122 — 219 316 —
SSB-0689 175.00 — — — 22 3 — — —
SSB-0709 180.00 — 26 124 21 220 317 414
SSB-0728 185.00 — — — 22 3 — — —
SSB-0748 190.00 — 28 — 24 221 318 415
SSB-0787 200.00 — — 126 — 222 319 416
SSB-0807 205.00 — — — 26 — — —
SSB-0827 210.00 — 30 128 — — — 417
SSB-0847 215.00 — — — — 224 320 —
SSB-0866 220.00 — 32 — 28 — — —
SSB-0886 225.00 — — 130 — — 321 418
SSB-0906 230.00 — 34 — — 226 — —
SSB-0925 235.00 — — — 30 — — —
SSB-0945 240.00 — — 132 — — 322 —
SSB-0984 250.00 — 36 — 32 228 — 419
SSB-1024 260.00 — 38 134 — — 324 —
SSB-1043 265.00 — — — 34 — — 420
SSB-1063 270.00 — — — — 230 — —
SSB-1102 280.00 — 40 136 36 — 326 —
SSB-1142 290.00 — — 138 — 232 — 421
SSB-1181 300.00 — — — 38 — 328 —
SSB-1221 310.00 — — 140 — 234 — —
SSB-1260 320.00 — — — 40 236 330 422
SSB-1339 340.00 — — 144 42 238 332 —
SSB-1378 350.00 — — — 44 — — —
SSB-1417 360.00 — — 148 — 240 334 —
SSB-1457 370.00 — — — 46 — — —
SSB-1496 380.00 — — — — — 336 —
SSB-1535 390.00 — — — 48 — — —
SSB-1575 400.00 — — 152 — 244 338 —
SSB-1614 410.00 — — — 50 — — —
SSB-1654 420.00 — — 156 — — 340 —
SSB-1693 430.00 — — — 52 — — —
SSB-1732 440.00 — — — — 248 342 —
SSB-1811 460.00 — — 160 56 — 344 —
SSB-1890 480.00 — — 164 — 252 — —
SSB-1969 500.00 — — — 64 256 348 —
SSB-2126 540.00 — — — — 260 352 —
SSB-2284 580.00 — — — — 264 356
1
2
3
Check bearing dimensions.
4

C/CS Series - Crest-To-Crest® Springs
Operates Clears Number Number

Smalley Part in Bore Shaft Load Work Free of of Radial Spring
Number 1, 2, 5 Diameter Diameter (lb) Height Height 3 Waves Turns Thickness Wall Rate 4
C025-L1* .250 .150 2 .033 .075 2.5 3 .006 .024 48
C025-L2* .250 .150 2 .050 .100 2.5 4 .006 .024 40
C025-L3* .250 .150 2 .060 .125 2.5 5 .006 .024 31
C025-L4* .250 .150 2 .075 .150 2.5 6 .006 .024 27
C025-L5* .250 .150 2 .085 .175 2.5 7 .006 .024 22
C025-L6* .250 .150 2 .095 .200 2.5 8 .006 .024 19
C025-L7* .250 .150 2 .120 .225 2.5 9 .006 .024 19
C025-L8* .250 .150 2 .140 .275 2.5 11 .006 .024 15
C025-L9* .250 .150 2 .170 .325 2.5 13 .006 .024 13
C025-M1* .250 .150 5 .037 .075 2.5 3 .008 .024 132
C025-M2* .250 .150 5 .048 .100 2.5 4 .008 .024 96
C025-M3* .250 .150 5 .065 .125 2.5 5 .008 .024 83
C025-M4* .250 .150 5 .075 .150 2.5 6 .008 .024 67
Product Dimensions C025-M5* .250 .150 5 .090 .175 2.5 7 .008 .024 59
All dimensions in inches C025-M6* .250 .150 5 .100 .200 2.5 8 .008 .024 50
unless otherwise specified. C025-M7* .250 .150 5 .120 .225 2.5 9 .008 .024 48
C025-M8* .250 .150 5 .148 .275 2.5 11 .008 .024 39
RADIAL C025-M9* .250 .150 5 .175 .325 2.5 13 .008 .024 33
WALL
C031-L1 .312 .200 3 .070 .114 2.5 3 .008 .032 68
C031-L2 .312 .200 3 .096 .152 2.5 4 .008 .032 54
OPERATES CLEARS
C031-L3 .312 .200 3 .118 .190 2.5 5 .008 .032 42
IN BORE SHAFT C031-L4 .312 .200 3 .145 .228 2.5 6 .008 .032 36
DIAMETER DIAMETER C031-L5 .312 .200 3 .165 .266 2.5 7 .008 .032 30
C031-L6 .312 .200 3 .195 .304 2.5 8 .008 .032 28
C031-L7 .312 .200 3 .215 .342 2.5 9 .008 .032 24
C031-L8 .312 .200 3 .262 .418 2.5 11 .008 .032 19
C031-L9 .312 .200 3 .309 .494 2.5 13 .008 .032 16
C031-M1 .312 .200 6 .072 .114 2.5 3 .010 .032 143
Plain Ends C031-M2 .312 .200 6 .096 .152 2.5 4 .010 .032 107
MULTI-WAVE C031-M3 .312 .200 6 .123 .190 2.5 5 .010 .032 90
FREE HEIGHT (SEE TABLE)
C031-M4 .312 .200 6 .144 .228 2.5 6 .010 .032 71
TURNS C031-M5 .312 .200 6 .176 .266 2.5 7 .010 .032 67
C031-M6 .312 .200 6 .197 .304 2.5 8 .010 .032 56
C031-M7 .312 .200 6 .227 .342 2.5 9 .010 .032 52
C031-M8 .312 .200 6 .278 .418 2.5 11 .010 .032 43
LOAD AT WIRE C031-M9 .312 .200 6 .336 .494 2.5 13 .010 .032 38
WORK HEIGHT THICKNESS C037-L1 .375 .250 4 .062 .150 2.5 3 .008 .032 45
C037-L2 .375 .250 4 .098 .200 2.5 4 .008 .032 39
Shim Ends C037-L3 .375 .250 4 .108 .250 2.5 5 .008 .032 28
C037-L4 .375 .250 4 .135 .300 2.5 6 .008 .032 24
FREE HEIGHT MULTI-WAVE C037-L5 .375 .250 4 .150 .350 2.5 7 .008 .032 20
(SEE TABLE) C037-L6 .375 .250 4 .184 .400 2.5 8 .008 .032 19
TURNS
C037-L7 .375 .250 4 .195 .450 2.5 9 .008 .032 16
C037-L8 .375 .250 4 .228 .500 2.5 10 .008 .032 15
C037-L9 .375 .250 4 .240 .550 2.5 11 .008 .032 13
C037-M1 .375 .250 7 .081 .150 2.5 3 .011 .032 101
LOAD AT
C037-M2 .375 .250 7 .119 .200 2.5 4 .011 .032 86
WIRE
WORK HEIGHT THICKNESS C037-M3 .375 .250 7 .145 .250 2.5 5 .011 .032 67
C037-M4 .375 .250 7 .180 .300 2.5 6 .011 .032 58
C037-M5 .375 .250 7 .202 .350 2.5 7 .011 .032 47
C037-M6 .375 .250 7 .240 .400 2.5 8 .011 .032 44
C037-M7 .375 .250 7 .262 .450 2.5 9 .011 .032 37
Order Options C037-M8 .375 .250 7 .298 .500 2.5 10 .011 .032 35
C037-M9 .375 .250 7 .327 .550 2.5 11 .011 .032 31
C 037-L1 1
Use “C” prefix for plain ends. Use “CS” prefix for squared-shim ends.
2
End options:
3
Plain ends . . . . . . . . . . . . . C
4
5
Squared-shim ends . . . . . . . CS
Material option: *Not available with shim ends

Carbon Steel . . . . . . . . (blank)
Stainless Steel . . . . . . . . . -S17

C/CS Series

C043-L1 .437 .281 4 .063 .165 2.5 3 .008 .040 39
C043-L2 .437 .281 4 .093 .220 2.5 4 .008 .040 31
C043-L3 .437 .281 4 .109 .275 2.5 5 .008 .040 24
C043-L4 .437 .281 4 .143 .330 2.5 6 .008 .040 21
C043-L5 .437 .281 4 .160 .385 2.5 7 .008 .040 18
C043-L6 .437 .281 4 .195 .440 2.5 8 .008 .040 16
C043-L7 .437 .281 4 .210 .495 2.5 9 .008 .040 14
C043-L8 .437 .281 4 .240 .550 2.5 10 .008 .040 13
C043-L9 .437 .281 4 .260 .605 2.5 11 .008 .040 12
C043-M1 .437 .281 8 .082 .165 2.5 3 .011 .046 96
C043-M2 .437 .281 8 .115 .220 2.5 4 .011 .046 76
C043-M3 .437 .281 8 .142 .275 2.5 5 .011 .046 60
C043-M4 .437 .281 8 .179 .330 2.5 6 .011 .046 53
C043-M5 .437 .281 8 .198 .385 2.5 7 .011 .046 43 Product Dimensions
C043-M6 .437 .281 8 .231 .440 2.5 8 .011 .046 38
C043-M7 .437 .281 8 .255 .495 2.5 9 .011 .046 33 unless otherwise specified.
C043-M8 .437 .281 8 .290 .550 2.5 10 .011 .046 31
C043-M9 .437 .281 8 .319 .605 2.5 11 .011 .046 28 RADIAL
WALL
C050-L1 .500 .312 5 .062 .180 2.5 3 .008 .056 42
C050-L2 .500 .312 5 .090 .240 2.5 4 .008 .056 33
C050-L3 .500 .312 5 .107 .300 2.5 5 .008 .056 26 OPERATES CLEARS
C050-L4 .500 .312 5 .136 .360 2.5 6 .008 .056 22 IN BORE SHAFT
C050-L5 .500 .312 5 .150 .420 2.5 7 .008 .056 19 DIAMETER DIAMETER
C050-L6 .500 .312 5 .180 .480 2.5 8 .008 .056 17
C050-L7 .500 .312 5 .195 .540 2.5 9 .008 .056 14
C050-L8 .500 .312 5 .220 .600 2.5 10 .008 .056 13
C050-L9 .500 .312 5 .240 .660 2.5 11 .008 .056 12
C050-M1 .500 .312 10 .065 .180 2.5 3 .010 .058 87
C050-M2 .500 .312 10 .092 .240 2.5 4 .010 .058 68 Plain Ends
C050-M3 .500 .312 10 .114 .300 2.5 5 .010 .058 54 MULTI-WAVE
C050-M4 .500 .312 10 .147 .360 2.5 6 .010 .058 47
C050-M5 .500 .312 10 .162 .420 2.5 7 .010 .058 39 TURNS
C050-M6 .500 .312 10 .196 .480 2.5 8 .010 .058 35
C050-M7 .500 .312 10 .207 .540 2.5 9 .010 .058 30
C050-M8 .500 .312 10 .246 .600 2.5 10 .010 .058 28
C050-M9 .500 .312 10 .264 .660 2.5 11 .010 .058 25 LOAD AT WIRE
C050-H1 .500 .312 15 .075 .180 2.5 3 .012 .060 143 WORK HEIGHT THICKNESS
C050-H2 .500 .312 15 .110 .240 2.5 4 .012 .060 115
C050-H3 .500 .312 15 .136 .300 2.5 5 .012 .060 91 Shim Ends
C050-H4 .500 .312 15 .167 .360 2.5 6 .012 .060 78
C050-H5 .500 .312 15 .182 .420 2.5 7 .012 .060 63 FREE HEIGHT MULTI-WAVE
C050-H6 .500 .312 15 .216 .480 2.5 8 .012 .060 57 (SEE TABLE)
C050-H7 .500 .312 15 .240 .540 2.5 9 .012 .060 50 TURNS
C050-H8 .500 .312 15 .280 .600 2.5 10 .012 .060 47
C050-H9 .500 .312 15 .312 .660 2.5 11 .012 .060 43
C056-L1 .562 .375 5 .080 .195 2.5 3 .009 .058 43
C056-L2 .562 .375 5 .125 .260 2.5 4 .009 .058 37 LOAD AT WIRE
C056-L3 .562 .375 5 .135 .325 2.5 5 .009 .058 26 WORK HEIGHT THICKNESS
C056-L4 .562 .375 5 .180 .390 2.5 6 .009 .058 24
C056-L5 .562 .375 5 .190 .455 2.5 7 .009 .058 19
C056-L6 .562 .375 5 .230 .520 2.5 8 .009 .058 17
C056-L7 .562 .375 5 .260 .585 2.5 9 .009 .058 15
C056-L8 .562 .375 5 .285 .650 2.5 10 .009 .058 14 Order Options
C056-L9 .562 .375 5 .315 .715 2.5 11 .009 .058 13
C 037-L1
1
2
3
Reference dimension. End options:
4
Plain ends . . . . . . . . . . . . . C
5
Material option:


C056-M1 .562 .375 11 .086 .195 2.5 3 .012 .060 101
C056-M2 .562 .375 11 .123 .260 2.5 4 .012 .060 80
C056-M3 .562 .375 11 .145 .325 2.5 5 .012 .060 61
C056-M4 .562 .375 11 .187 .390 2.5 6 .012 .060 54
C056-M5 .562 .375 11 .209 .455 2.5 7 .012 .060 45
C056-M6 .562 .375 11 .253 .520 2.5 8 .012 .060 41
C056-M7 .562 .375 11 .273 .585 2.5 9 .012 .060 35
C056-M8 .562 .375 11 .318 .650 2.5 10 .012 .060 33
C056-M9 .562 .375 11 .343 .715 2.5 11 .012 .060 30
C056-H1 .562 .375 18 .093 .195 2.5 3 .015 .060 176
C056-H2 .562 .375 18 .136 .260 2.5 4 .015 .060 145
C056-H3 .562 .375 18 .165 .325 2.5 5 .015 .060 113
C056-H4 .562 .375 18 .212 .390 2.5 6 .015 .060 101
C056-H5 .562 .375 18 .245 .455 2.5 7 .015 .060 86
Product Dimensions
C056-H6 .562 .375 18 .282 .520 2.5 8 .015 .060 76
All dimensions in inches C056-H7 .562 .375 18 .323 .585 2.5 9 .015 .060 69
unless otherwise specified. C056-H8 .562 .375 18 .360 .650 2.5 10 .015 .060 62
RADIAL C056-H9 .562 .375 18 .408 .715 2.5 11 .015 .060 59
WALL C062-L1 .625 .450 6 .055 .180 2.5 3 .010 .058 48
C062-L2 .625 .450 6 .068 .240 2.5 4 .010 .058 35
C062-L3 .625 .450 6 .085 .300 2.5 5 .010 .058 28
OPERATES CLEARS
IN BORE SHAFT
C062-L4 .625 .450 6 .106 .360 2.5 6 .010 .058 24
DIAMETER DIAMETER C062-L5 .625 .450 6 .128 .420 2.5 7 .010 .058 21
C062-L6 .625 .450 6 .165 .540 2.5 9 .010 .058 16
C062-L7 .625 .450 6 .202 .660 2.5 11 .010 .058 13
C062-L8 .625 .450 6 .238 .780 2.5 13 .010 .058 11
C062-M1 .625 .450 12 .104 .180 3.5 3 .010 .058 158
C062-M2 .625 .450 12 .130 .240 3.5 4 .010 .058 109
Plain Ends C062-M3 .625 .450 12 .175 .300 3.5 5 .010 .058 96
FREE HEIGHT
MULTI-WAVE C062-M4 .625 .450 12 .206 .360 3.5 6 .010 .058 78
(SEE TABLE)
C062-M5 .625 .450 12 .246 .420 3.5 7 .010 .058 69
TURNS C062-M6 .625 .450 12 .317 .540 3.5 9 .010 .058 54
C062-M7 .625 .450 12 .386 .660 3.5 11 .010 .058 44
C062-M8 .625 .450 12 .454 .780 3.5 13 .010 .058 37
C062-H1 .625 .450 20 .102 .180 3.5 3 .012 .060 256
LOAD AT WIRE
C062-H2 .625 .450 20 .135 .240 3.5 4 .012 .060 190
WORK HEIGHT THICKNESS C062-H3 .625 .450 20 .175 .300 3.5 5 .012 .060 160
C062-H4 .625 .450 20 .205 .360 3.5 6 .012 .060 129
C062-H5 .625 .450 20 .245 .420 3.5 7 .012 .060 114
Shim Ends C062-H6 .625 .450 20 .315 .540 3.5 9 .012 .060 89
MULTI-WAVE C062-H7 .625 .450 20 .390 .660 3.5 11 .012 .060 74
FREE HEIGHT
(SEE TABLE) C062-H8 .625 .450 20 .465 .780 3.5 13 .012 .060 63
C075-L1 .750 .550 7 .142 .250 3.5 3 .008 .071 65
TURNS
C075-L2 .750 .550 7 .187 .333 3.5 4 .008 .071 48
C075-L3 .750 .550 7 .246 .417 3.5 5 .008 .071 41
C075-L4 .750 .550 7 .285 .500 3.5 6 .008 .071 33
C075-L5 .750 .550 7 .348 .583 3.5 7 .008 .071 30
LOAD AT
WORK HEIGHT
WIRE C075-L6 .750 .550 7 .446 .750 3.5 9 .008 .071 23
THICKNESS
C075-L7 .750 .550 7 .580 1.000 3.5 12 .008 .071 17
C075-M1 .750 .550 13 .159 .250 3.5 3 .010 .078 143
C075-M2 .750 .550 13 .203 .333 3.5 4 .010 .078 100
C075-M3 .750 .550 13 .270 .417 3.5 5 .010 .078 88
Order Options C075-M4 .750 .550 13 .314 .500 3.5 6 .010 .078 70
C075-M5 .750 .550 13 .381 .583 3.5 7 .010 .078 64
C 037-L1 C075-M6 .750 .550 13 .489 .750 3.5 9 .010 .078 50
C075-M7 .750 .550 13 .649 1.000 3.5 12 .010 .078 37
C075-H1 .750 .550 22 .169 .250 3.5 3 .013 .079 272
C075-H2 .750 .550 22 .215 .333 3.5 4 .013 .079 186
End options: C075-H3 .750 .550 22 .291 .417 3.5 5 .013 .079 175
Plain ends . . . . . . . . . . . . . C C075-H4 .750 .550 22 .335 .500 3.5 6 .013 .079 133
Squared-shim ends . . . . . . . CS C075-H5 .750 .550 22 .405 .583 3.5 7 .013 .079 124
C075-H6 .750 .550 22 .526 .750 3.5 9 .013 .079 98
Material option: C075-H7 .750 .550 22 .699 1.000 3.5 12 .013 .079 73
Stainless Steel . . . . . . . . . -S17 1
2
3
4
26 smalley.com 5
See pages 132-133 for How to Order. No-Tooling-Charges™ For Customs
C/CS Series

C087-L1 .875 .600 12 .117 .250 3.5 3 .010 .086 90
C087-L2 .875 .600 12 .158 .333 3.5 4 .010 .086 69
C087-L3 .875 .600 12 .207 .417 3.5 5 .010 .086 57
C087-L4 .875 .600 12 .242 .500 3.5 6 .010 .086 47
C087-L5 .875 .600 12 .287 .583 3.5 7 .010 .086 41
C087-L6 .875 .600 12 .378 .750 3.5 9 .010 .086 32
C087-L7 .875 .600 12 .498 1.000 3.5 12 .010 .086 24
C087-M1 .875 .600 18 .124 .250 3.5 3 .012 .094 148
C087-M2 .875 .600 18 .164 .333 3.5 4 .012 .094 108
C087-M3 .875 .600 18 .214 .417 3.5 5 .012 .094 89
C087-M4 .875 .600 18 .252 .500 3.5 6 .012 .094 76
C087-M5 .875 .600 18 .296 .583 3.5 7 .012 .094 66
C087-M6 .875 .600 18 .385 .750 3.5 9 .012 .094 50
C087-M7 .875 .600 18 .509 1.000 3.5 12 .012 .094 38
Product Dimensions
C087-H1 .875 .600 25 .166 .250 3.5 3 .015 .094 298
C087-H2 .875 .600 25 .214 .333 3.5 4 .015 .094 210 All dimensions in inches
C087-H3 .875 .600 25 .278 .417 3.5 5 .015 .094 180 unless otherwise specified.
C087-H4 .875 .600 25 .327 .500 3.5 6 .015 .094 145 RADIAL
C087-H5 .875 .600 25 .395 .583 3.5 7 .015 .094 133 WALL
C087-H6 .875 .600 25 .510 .750 3.5 9 .015 .094 104
C087-H7 .875 .600 25 .670 1.000 3.5 12 .015 .094 78
OPERATES CLEARS
C100-L1 1.000 .730 12 .084 .250 3.5 3 .010 .086 72 IN BORE SHAFT
C100-L2 1.000 .730 12 .108 .333 3.5 4 .010 .086 53 DIAMETER DIAMETER
C100-L3 1.000 .730 12 .145 .417 3.5 5 .010 .086 44
C100-L4 1.000 .730 12 .165 .500 3.5 6 .010 .086 36
C100-L5 1.000 .730 12 .201 .583 3.5 7 .010 .086 31
C100-L6 1.000 .730 12 .258 .750 3.5 9 .010 .086 24
C100-L7 1.000 .730 12 .342 1.000 3.5 12 .010 .086 18
C100-L8 1.000 .730 12 .445 1.250 3.5 15 .010 .086 15 Plain Ends
C100-L9 1.000 .730 12 .519 1.500 3.5 18 .010 .086 12 FREE HEIGHT
MULTI-WAVE
(SEE TABLE)
C100-L10 1.000 .730 12 .633 1.750 3.5 21 .010 .086 11
C100-L11 1.000 .730 12 .710 2.000 3.5 24 .010 .086 9 TURNS
C100-M1 1.000 .730 18 .087 .250 3.5 3 .012 .094 110
C100-M2 1.000 .730 18 .113 .333 3.5 4 .012 .094 82
C100-M3 1.000 .730 18 .148 .417 3.5 5 .012 .094 67
C100-M4 1.000 .730 18 .175 .500 3.5 6 .012 .094 55 LOAD AT WIRE
C100-M5 1.000 .730 18 .212 .583 3.5 7 .012 .094 49 WORK HEIGHT THICKNESS
C100-M6 1.000 .730 18 .276 .750 3.5 9 .012 .094 38
C100-M7 1.000 .730 18 .360 1.000 3.5 12 .012 .094 28
C100-M8 1.000 .730 18 .452 1.250 3.5 15 .012 .094 23 Shim Ends
C100-M9 1.000 .730 18 .549 1.500 3.5 18 .012 .094 19 MULTI-WAVE
FREE HEIGHT
C100-M10 1.000 .730 18 .650 1.750 3.5 21 .012 .094 16 (SEE TABLE)
C100-M11 1.000 .730 18 .720 2.000 3.5 24 .012 .094 14
TURNS
C100-H1 1.000 .730 25 .131 .250 3.5 3 .015 .094 210
C100-H2 1.000 .730 25 .174 .333 3.5 4 .015 .094 157
C100-H3 1.000 .730 25 .227 .417 3.5 5 .015 .094 132
C100-H4 1.000 .730 25 .266 .500 3.5 6 .015 .094 107
LOAD AT
C100-H5 1.000 .730 25 .319 .583 3.5 7 .015 .094 95 WORK HEIGHT
WIRE
THICKNESS
C100-H6 1.000 .730 25 .406 .750 3.5 9 .015 .094 73
C100-H7 1.000 .730 25 .541 1.000 3.5 12 .015 .094 54
C100-H8 1.000 .730 25 .688 1.250 3.5 15 .015 .094 45
C100-H9 1.000 .730 25 .813 1.500 3.5 18 .015 .094 36
C100-H10 1.000 .730 25 .957 1.750 3.5 21 .015 .094 32 Order Options
C100-H11 1.000 .730 25 1.083 2.000 3.5 24 .015 .094 27
1
C 037-L1
2
3
4
Theoretical dimension; measured in lb/in. End options:
5
See pages 132-133 for How to Order. Plain ends . . . . . . . . . . . . . C
Material option:


C112-L1 1.125 .850 12 .146 .300 3.5 3 .012 .094 78
C112-L2 1.125 .850 12 .186 .400 3.5 4 .012 .094 56
C112-L3 1.125 .850 12 .250 .500 3.5 5 .012 .094 48
C112-L4 1.125 .850 12 .295 .600 3.5 6 .012 .094 39
C112-L5 1.125 .850 12 .344 .700 3.5 7 .012 .094 34
C112-L6 1.125 .850 12 .392 .800 3.5 8 .012 .094 29
C112-L7 1.125 .850 12 .488 1.000 3.5 10 .012 .094 23
C112-L8 1.125 .850 12 .659 1.300 3.5 13 .012 .094 19
C112-L9 1.125 .850 12 .807 1.600 3.5 16 .012 .094 15
C112-L10 1.125 .850 12 1.017 2.000 3.5 20 .012 .094 12
C112-M1 1.125 .850 20 .160 .300 3.5 3 .015 .094 143
C112-M2 1.125 .850 20 .202 .400 3.5 4 .015 .094 101
C112-M3 1.125 .850 20 .270 .500 3.5 5 .015 .094 87
C112-M4 1.125 .850 20 .318 .600 3.5 6 .015 .094 71
Product Dimensions
C112-M5 1.125 .850 20 .381 .700 3.5 7 .015 .094 63
All dimensions in inches C112-M6 1.125 .850 20 .427 .800 3.5 8 .015 .094 54
unless otherwise specified. C112-M7 1.125 .850 20 .536 1.000 3.5 10 .015 .094 43
RADIAL C112-M8 1.125 .850 20 .708 1.300 3.5 13 .015 .094 34
WALL C112-M9 1.125 .850 20 .861 1.600 3.5 16 .015 .094 27
C112-M10 1.125 .850 20 1.088 2.000 3.5 20 .015 .094 22
C112-H1 1.125 .850 30 .178 .300 3.5 3 .018 .094 246
OPERATES CLEARS C112-H2 1.125 .850 30 .229 .400 3.5 4 .018 .094 175
IN BORE SHAFT
DIAMETER DIAMETER C112-H3 1.125 .850 30 .303 .500 3.5 5 .018 .094 152
C112-H4 1.125 .850 30 .350 .600 3.5 6 .018 .094 120
C112-H5 1.125 .850 30 .421 .700 3.5 7 .018 .094 108
C112-H6 1.125 .850 30 .470 .800 3.5 8 .018 .094 91
C112-H7 1.125 .850 30 .593 1.000 3.5 10 .018 .094 74
C112-H8 1.125 .850 30 .787 1.300 3.5 13 .018 .094 58
Plain Ends C112-H9 1.125 .850 30 .956 1.600 3.5 16 .018 .094 47
MULTI-WAVE C112-H10 1.125 .850 30 1.202 2.000 3.5 20 .018 .094 38
FREE HEIGHT (SEE TABLE) C125-L1 1.250 1.000 12 .084 .250 3.5 3 .012 .094 56
TURNS
C125-L2 1.250 1.000 12 .113 .400 3.5 4 .012 .094 42
C125-L3 1.250 1.000 12 .149 .500 3.5 5 .012 .094 34
C125-L4 1.250 1.000 12 .172 .600 3.5 6 .012 .094 28
C125-L5 1.250 1.000 12 .207 .700 3.5 7 .012 .094 24
LOAD AT C125-L6 1.250 1.000 12 .227 .800 3.5 8 .012 .094 21
WIRE
WORK HEIGHT THICKNESS C125-L7 1.250 1.000 12 .301 1.000 3.5 10 .012 .094 17
C125-L8 1.250 1.000 12 .395 1.300 3.5 13 .012 .094 13
C125-L9 1.250 1.000 12 .467 1.600 3.5 16 .012 .094 11
Shim Ends C125-L10 1.250 1.000 12 .591 2.000 3.5 20 .012 .094 9
MULTI-WAVE C125-M1 1.250 1.000 20 .124 .300 3.5 3 .015 .094 114
FREE HEIGHT
(SEE TABLE) C125-M2 1.250 1.000 20 .165 .400 3.5 4 .015 .094 85
C125-M3 1.250 1.000 20 .215 .500 3.5 5 .015 .094 70
TURNS C125-M4 1.250 1.000 20 .253 .600 3.5 6 .015 .094 58
C125-M5 1.250 1.000 20 .303 .700 3.5 7 .015 .094 50
C125-M6 1.250 1.000 20 .341 .800 3.5 8 .015 .094 44
C125-M7 1.250 1.000 20 .427 1.000 3.5 10 .015 .094 35
LOAD AT WIRE C125-M8 1.250 1.000 20 .577 1.300 3.5 13 .015 .094 28
WORK HEIGHT THICKNESS
C125-M9 1.250 1.000 20 .692 1.600 3.5 16 .015 .094 22
C125-M10 1.250 1.000 20 .866 2.000 3.5 20 .015 .094 18
C125-H1 1.250 1.000 30 .158 .300 3.5 3 .019 .094 210
C125-H2 1.250 1.000 30 .210 .400 3.5 4 .019 .094 158
Order Options C125-H3 1.250 1.000 30 .272 .500 3.5 5 .019 .094 132
C125-H4 1.250 1.000 30 .320 .600 3.5 6 .019 .094 107
C 037-L1 C125-H5
C125-H6
1.250
1.250
1.000 30 .384 .700
1.000 30 .433 .800
3.5
3.5
7
8
.019
.019
.094 95
.094 82
C125-H7 1.250 1.000 30 .538 1.000 3.5 10 .019 .094 65
C125-H8 1.250 1.000 30 .717 1.300 3.5 13 .019 .094 51
End options: C125-H9 1.250 1.000 30 .878 1.600 3.5 16 .019 .094 42
Plain ends . . . . . . . . . . . . . C C125-H10 1.250 1.000 30 1.103 2.000 3.5 20 .019 .094 33
1
Material option: 2
Carbon Steel . . . . . . . . (blank) 3
4
5

C/CS Series

C137-L1 1.375 1.030 15 .075 .300 3.5 3 .012 .122 67
C137-L2 1.375 1.030 15 .099 .400 3.5 4 .012 .122 50
C137-L3 1.375 1.030 15 .129 .500 3.5 5 .012 .122 40
C137-L4 1.375 1.030 15 .155 .600 3.5 6 .012 .122 34
C137-L5 1.375 1.030 15 .179 .700 3.5 7 .012 .122 29
C137-L6 1.375 1.030 15 .206 .800 3.5 8 .012 .122 25
C137-L7 1.375 1.030 15 .256 1.000 3.5 10 .012 .122 20
C137-L8 1.375 1.030 15 .341 1.300 3.5 13 .012 .122 16
C137-L9 1.375 1.030 15 .424 1.600 3.5 16 .012 .122 13
C137-L10 1.375 1.030 15 .530 2.000 3.5 20 .012 .122 10
C137-M1 1.375 1.030 25 .142 .300 3.5 3 .016 .133 158
C137-M2 1.375 1.030 25 .186 .400 3.5 4 .016 .133 117
C137-M3 1.375 1.030 25 .240 .500 3.5 5 .016 .133 96
C137-M4 1.375 1.030 25 .281 .600 3.5 6 .016 .133 78 Product Dimensions
C137-M5 1.375 1.030 25 .340 .700 3.5 7 .016 .133 69
C137-M6 1.375 1.030 25 .384 .800 3.5 8 .016 .133 60 All dimensions in inches
C137-M7 1.375 1.030 25 .486 1.000 3.5 10 .016 .133 49 unless otherwise specified.
C137-M8 1.375 1.030 25 .632 1.300 3.5 13 .016 .133 37 RADIAL
C137-M9 1.375 1.030 25 .788 1.600 3.5 16 .016 .133 31 WALL
C137-M10 1.375 1.030 25 .982 2.000 3.5 20 .016 .133 25
C137-H1 1.375 1.030 35 .149 .300 3.5 3 .018 .133 232
OPERATES CLEARS
C137-H2 1.375 1.030 35 .189 .400 3.5 4 .018 .133 166 IN BORE SHAFT
C137-H3 1.375 1.030 35 .247 .500 3.5 5 .018 .133 138 DIAMETER DIAMETER
C137-H4 1.375 1.030 35 .287 .600 3.5 6 .018 .133 112
C137-H5 1.375 1.030 35 .343 .700 3.5 7 .018 .133 98
C137-H6 1.375 1.030 35 .390 .800 3.5 8 .018 .133 85
C137-H7 1.375 1.030 35 .490 1.000 3.5 10 .018 .133 69
C137-H8 1.375 1.030 35 .646 1.300 3.5 13 .018 .133 54
C137-H9 1.375 1.030 35 .793 1.600 3.5 16 .018 .133 43 Plain Ends
C137-H10 1.375 1.030 35 1.000 2.000 3.5 20 .018 .133 35 FREE HEIGHT
MULTI-WAVE
(SEE TABLE)
C150-L1 1.500 1.140 20 .129 .300 3.5 3 .016 .133 117
C150-L2 1.500 1.140 20 .164 .400 3.5 4 .016 .133 85 TURNS
C150-L3 1.500 1.140 20 .213 .500 3.5 5 .016 .133 70
C150-L4 1.500 1.140 20 .247 .600 3.5 6 .016 .133 57
C150-L5 1.500 1.140 20 .301 .700 3.5 7 .016 .133 50
C150-L6 1.500 1.140 20 .337 .800 3.5 8 .016 .133 43 LOAD AT WIRE
C150-L7 1.500 1.140 20 .430 1.000 3.5 10 .016 .133 35 WORK HEIGHT THICKNESS
C150-L8 1.500 1.140 20 .565 1.300 3.5 13 .016 .133 27
C150-L9 1.500 1.140 20 .694 1.600 3.5 16 .016 .133 22
C150-L10 1.500 1.140 20 .866 2.000 3.5 20 .016 .133 18 Shim Ends
C150-M1 1.500 1.140 35 .122 .300 3.5 3 .018 .133 197 MULTI-WAVE
FREE HEIGHT
C150-M2 1.500 1.140 35 .158 .400 3.5 4 .018 .133 145 (SEE TABLE)
C150-M3 1.500 1.140 35 .206 .500 3.5 5 .018 .133 119
TURNS
C150-M4 1.500 1.140 35 .241 .600 3.5 6 .018 .133 97
C150-M5 1.500 1.140 35 .291 .700 3.5 7 .018 .133 86
C150-M6 1.500 1.140 35 .324 .800 3.5 8 .018 .133 74
C150-M7 1.500 1.140 35 .409 1.000 3.5 10 .018 .133 59
LOAD AT
C150-M8 1.500 1.140 35 .540 1.300 3.5 13 .018 .133 46 WORK HEIGHT
WIRE
THICKNESS
C150-M9 1.500 1.140 35 .657 1.600 3.5 16 .018 .133 37
C150-M10 1.500 1.140 35 .835 2.000 3.5 20 .018 .133 30
C150-H1 1.500 1.140 60 .166 .300 4.5 3 .018 .133 448
C150-H2 1.500 1.140 60 .216 .400 4.5 4 .018 .133 326
C150-H3 1.500 1.140 60 .278 .500 4.5 5 .018 .133 270 Order Options
C150-H4 1.500 1.140 60 .329 .600 4.5 6 .018 .133 221
C150-H5 1.500 1.140 60 .390 .700 4.5 7 .018 .133 194 C 037-L1
C150-H6 1.500 1.140 60 .443 .800 4.5 8 .018 .133 168
C150-H7 1.500 1.140 60 .555 1.000 4.5 10 .018 .133 135
C150-H8 1.500 1.140 60 .726 1.300 4.5 13 .018 .133 105
C150-H9 1.500 1.140 60 .890 1.600 4.5 16 .018 .133 85
End options:
C150-H10 1.500 1.140 60 1.119 2.000 4.5 20 .018 .133 68 Plain ends . . . . . . . . . . . . . C
1
2
Add suffix “-S17” for 17-7 stainless steel. Material option:
3
Reference dimension. Carbon Steel . . . . . . . . (blank)
4
Theoretical dimension; measured in lb/in. Stainless Steel . . . . . . . . . -S17
5


C175-L1 1.750 1.340 25 .155 .375 3.5 3 .018 .143 114
C175-L2 1.750 1.340 25 .200 .500 3.5 4 .018 .143 83
C175-L3 1.750 1.340 25 .265 .625 3.5 5 .018 .143 69
C175-L4 1.750 1.340 25 .310 .750 3.5 6 .018 .143 57
C175-L5 1.750 1.340 25 .367 .870 3.5 7 .018 .143 50
C175-L6 1.750 1.340 25 .415 1.000 3.5 8 .018 .143 43
C175-L7 1.750 1.340 25 .523 1.250 3.5 10 .018 .143 34
C175-L8 1.750 1.340 25 .638 1.500 3.5 12 .018 .143 29
C175-L9 1.750 1.340 25 .737 1.750 3.5 14 .018 .143 25
C175-L10 1.750 1.340 25 .844 2.000 3.5 16 .018 .143 22
C175-M1 1.750 1.340 50 .188 .375 4.5 3 .018 .143 267
C175-M2 1.750 1.340 50 .244 .500 4.5 4 .018 .143 195
C175-M3 1.750 1.340 50 .315 .625 4.5 5 .018 .143 161
Product Dimensions C175-M4 1.750 1.340 50 .374 .750 4.5 6 .018 .143 133
C175-M5 1.750 1.340 50 .452 .870 4.5 7 .018 .143 120
C175-M6 1.750 1.340 50 .505 1.000 4.5 8 .018 .143 101
C175-M7 1.750 1.340 50 .629 1.250 4.5 10 .018 .143 81
RADIAL C175-M8 1.750 1.340 50 .768 1.500 4.5 12 .018 .143 68
WALL
C175-M9 1.750 1.340 50 .899 1.750 4.5 14 .018 .143 59
C175-M10 1.750 1.340 50 1.026 2.000 4.5 16 .018 .143 51
OPERATES CLEARS
C175-H1 1.750 1.340 90 .232 .375 4.5 3 .024 .148 629
IN BORE SHAFT C175-H2 1.750 1.340 90 .314 .500 4.5 4 .024 .148 484
DIAMETER DIAMETER C175-H3 1.750 1.340 90 .409 .625 4.5 5 .024 .148 417
C175-H4 1.750 1.340 90 .482 .750 4.5 6 .024 .148 336
C175-H5 1.750 1.340 90 .577 .870 4.5 7 .024 .148 307
C175-H6 1.750 1.340 90 .651 1.000 4.5 8 .024 .148 258
C175-H7 1.750 1.340 90 .813 1.250 4.5 10 .024 .148 206
C175-H8 1.750 1.340 90 .980 1.500 4.5 12 .024 .148 173
Plain Ends C175-H9 1.750 1.340 90 1.147 1.750 4.5 14 .024 .148 149
MULTI-WAVE C175-H10 1.750 1.340 90 1.317 2.000 4.5 16 .024 .148 132
C200-L1 2.000 1.600 25 .094 .375 3.5 3 .018 .143 89
TURNS C200-L2 2.000 1.600 25 .120 .500 3.5 4 .018 .143 66
C200-L3 2.000 1.600 25 .158 .625 3.5 5 .018 .143 54
C200-L4 2.000 1.600 25 .179 .750 3.5 6 .018 .143 44
C200-L5 2.000 1.600 25 .217 .870 3.5 7 .018 .143 38
LOAD AT WIRE C200-L6 2.000 1.600 25 .243 1.000 3.5 8 .018 .143 33
WORK HEIGHT THICKNESS C200-L7 2.000 1.600 25 .306 1.250 3.5 10 .018 .143 26
C200-L8 2.000 1.600 25 .365 1.500 3.5 12 .018 .143 22
C200-L9 2.000 1.600 25 .433 1.750 3.5 14 .018 .143 19
Shim Ends
C200-L10 2.000 1.600 25 .490 2.000 3.5 16 .018 .143 17
FREE HEIGHT MULTI-WAVE C200-M1 2.000 1.600 50 .140 .375 4.5 3 .018 .143 213
(SEE TABLE) C200-M2 2.000 1.600 50 .184 .500 4.5 4 .018 .143 158
TURNS
C200-M3 2.000 1.600 50 .245 .625 4.5 5 .018 .143 132
C200-M4 2.000 1.600 50 .278 .750 4.5 6 .018 .143 106
C200-M5 2.000 1.600 50 .345 .870 4.5 7 .018 .143 95
C200-M6 2.000 1.600 50 .395 1.000 4.5 8 .018 .143 83
LOAD AT
C200-M7 2.000 1.600 50 .498 1.250 4.5 10 .018 .143 66
WIRE
WORK HEIGHT THICKNESS C200-M8 2.000 1.600 50 .593 1.500 4.5 12 .018 .143 55
C200-M9 2.000 1.600 50 .694 1.750 4.5 14 .018 .143 47
C200-M10 2.000 1.600 50 .800 2.000 4.5 16 .018 .143 42
C200-H1 2.000 1.600 90 .197 .375 4.5 3 .024 .148 506
C200-H2 2.000 1.600 90 .258 .500 4.5 4 .024 .148 372
Order Options C200-H3 2.000 1.600 90 .332 .625 4.5 5 .024 .148 307
C200-H4 2.000 1.600 90 .389 .750 4.5 6 .024 .148 249
C 037-L1 C200-H5 2.000 1.600 90 .465 .870 4.5 7 .024 .148 222
C200-H6 2.000 1.600 90 .525 1.000 4.5 8 .024 .148 189
C200-H7 2.000 1.600 90 .661 1.250 4.5 10 .024 .148 153
End options: C200-H8 2.000 1.600 90 .781 1.500 4.5 12 .024 .148 125
Plain ends . . . . . . . . . . . . . C C200-H9 2.000 1.600 90 .941 1.750 4.5 14 .024 .148 111
C200-H10 2.000 1.600 90 1.069 2.000 4.5 16 .024 .148 97
1
Material option: 2
Carbon Steel . . . . . . . . (blank) 3
5

CM/CMS Series

Number 1, 2, 5 Diameter Diameter (N) Height Height 3 Waves Turns Thickness Wall Rate 4
CM06-L1* 6 4 6 .61 1.52 2.5 3 .13 .51 6.59
CM06-L2* 6 4 6 .81 2.03 2.5 4 .13 .51 4.92
CM06-L3* 6 4 6 1.02 2.54 2.5 5 .13 .51 3.95
CM06-L4* 6 4 6 1.22 3.05 2.5 6 .13 .51 3.28
CM06-L5* 6 4 6 1.42 3.56 2.5 7 .13 .51 2.80
CM06-L6* 6 4 6 1.63 4.06 2.5 8 .13 .51 2.47
CM06-L7* 6 4 6 1.83 4.57 2.5 9 .13 .51 2.19
CM06-L8* 6 4 6 2.24 5.59 2.5 11 .13 .51 1.79
CM06-L9* 6 4 6 2.64 6.60 2.5 13 .13 .51 1.52
CM06-M1* 6 4 12 .74 1.52 2.5 3 .15 .61 15.38
CM06-M2* 6 4 12 .97 2.03 2.5 4 .15 .61 11.32
CM06-M3* 6 4 12 1.22 2.54 2.5 5 .15 .61 9.09
CM06-M4* 6 4 12 1.47 3.05 2.5 6 .15 .61 7.59
CM06-M5* 6 4 12 1.70 3.56 2.5 7 .15 .61 6.45
CM06-M6* 6 4 12 1.96 4.06 2.5 8 .15 .61 5.71 Product Dimensions
CM06-M7* 6 4 12 2.18 4.57 2.5 9 .15 .61 5.02 All dimensions in inches
CM06-M8* 6 4 12 2.69 5.59 2.5 11 .15 .61 4.14 unless otherwise specified.
CM06-M9* 6 4 12 3.18 6.60 2.5 13 .15 .61 3.51
RADIAL
CM08-L1 8 5 15 1.70 2.82 2.5 3 .20 .81 13.39 WALL
CM08-L2 8 5 15 2.39 3.76 2.5 4 .20 .81 10.95
CM08-L3 8 5 15 2.74 4.70 2.5 5 .20 .81 7.65
CM08-L4 8 5 15 3.56 5.64 2.5 6 .20 .81 7.21 OPERATES CLEARS
CM08-L5 8 5 15 4.01 6.58 2.5 7 .20 .81 5.84 IN BORE SHAFT
DIAMETER DIAMETER
CM08-L6 8 5 15 4.57 7.52 2.5 8 .20 .81 5.08
CM08-L7 8 5 15 5.26 8.46 2.5 9 .20 .81 4.69
CM08-L8 8 5 15 6.35 10.34 2.5 11 .20 .81 3.76
CM08-L9 8 5 15 7.37 12.22 2.5 13 .20 .81 3.09
CM08-M1 8 5 30 1.78 2.82 2.5 3 .25 .81 28.85
CM08-M2 8 5 30 2.54 3.76 2.5 4 .25 .81 24.59 Plain Ends
CM08-M3 8 5 30 3.05 4.70 2.5 5 .25 .81 18.18 MULTI-WAVE
CM08-M4 8 5 30 3.81 5.64 2.5 6 .25 .81 16.39 FREE HEIGHT (SEE TABLE)
CM08-M5 8 5 30 4.32 6.58 2.5 7 .25 .81 13.27
CM08-M6 8 5 30 4.95 7.52 2.5 8 .25 .81 11.67 TURNS
CM08-M7 8 5 30 5.59 8.46 2.5 9 .25 .81 10.45
CM08-M8 8 5 30 6.86 10.34 2.5 11 .25 .81 8.62
CM08-M9 8 5 30 7.87 12.22 2.5 13 .25 .81 6.90
CM10-L1 10 7 18 1.91 3.96 2.5 3 .20 .81 8.78 LOAD AT WIRE
WORK HEIGHT THICKNESS
CM10-L2 10 7 18 2.54 5.28 2.5 4 .20 .81 6.57
CM10-L3 10 7 18 3.15 6.60 2.5 5 .20 .81 5.22
CM10-L4 10 7 18 3.78 7.92 2.5 6 .20 .81 4.35 Shim Ends
CM10-L5 10 7 18 4.42 9.25 2.5 7 .20 .81 3.73
MULTI-WAVE
CM10-L6 10 7 18 5.05 10.57 2.5 8 .20 .81 3.26 FREE HEIGHT
(SEE TABLE)
CM10-L7 10 7 18 5.69 11.89 2.5 9 .20 .81 2.90
CM10-L8 10 7 18 6.32 13.21 2.5 10 .20 .81 2.61 TURNS
CM10-L9 10 7 18 6.96 14.53 2.5 11 .20 .81 2.38
CM10-M1 10 7 35 2.03 3.96 2.5 3 .28 .81 18.13
CM10-M2 10 7 35 2.79 5.28 2.5 4 .28 .81 14.06
CM10-M3 10 7 35 3.56 6.60 2.5 5 .28 .81 11.51 LOAD AT WIRE
CM10-M4 10 7 35 4.32 7.92 2.5 6 .28 .81 9.72 WORK HEIGHT THICKNESS
CM10-M5 10 7 35 5.08 9.25 2.5 7 .28 .81 8.39
CM10-M6 10 7 35 5.84 10.57 2.5 8 .28 .81 7.40
CM10-M7 10 7 35 6.60 11.89 2.5 9 .28 .81 6.62
CM10-M8
CM10-M9
10
10
7
7
35 7.37 13.21
35 8.13 14.53
2.5
2.5
10
11
.28
.28
.81 5.99
.81 5.47
Order Options
CM12-L1
CM12-L2
12
12
9
9
20 1.47 4.34
20 1.98 5.79
2.5
2.5
3
4
.20
.20
1.02 6.97
1.02 5.25 C 030-L1
CM12-L3 12 9 20 2.46 7.24 2.5 5 .20 1.02 4.18
CM12-L4 12 9 20 2.95 8.69 2.5 6 .20 1.02 3.48
CM12-L5 12 9 20 3.45 10.13 2.5 7 .20 1.02 2.99 End options:
CM12-L6 12 9 20 3.94 11.58 2.5 8 .20 1.02 2.62 Plain ends . . . . . . . . . . . . . C
CM12-L7 12 9 20 4.45 13.03 2.5 9 .20 1.02 2.33 Squared-shim ends . . . . . . CMS
CM12-L8 12 9 20 4.93 14.48 2.5 10 .20 1.02 2.09
CM12-L9 12 9 20 5.44 15.93 2.5 11 .20 1.02 1.91 Material option:
1
Use “CM” prefix for plain ends. Use “CMS” prefix for squared-shim ends. * Not available with shim ends Stainless Steel . . . . . . . . . -S17
2
3
4
5
CM/CMS Series - Metric Crest-To-Crest® Springs

CM12-M1 12 8.5 40 2.36 4.34 2.5 3 .28 1.17 20.20
CM12-M2 12 8.5 40 3.18 5.79 2.5 4 .28 1.17 15.33
CM12-M3 12 8.5 40 3.96 7.24 2.5 5 .28 1.17 12.20
CM12-M4 12 8.5 40 4.75 8.69 2.5 6 .28 1.17 10.15
CM12-M5 12 8.5 40 5.54 10.13 2.5 7 .28 1.17 8.71
CM12-M6 12 8.5 40 6.32 11.58 2.5 8 .28 1.17 7.60
CM12-M7 12 8.5 40 7.11 13.03 2.5 9 .28 1.17 6.76
CM12-M8 12 8.5 40 7.92 14.48 2.5 10 .28 1.17 6.10
CM12-M9 12 8.5 40 8.71 15.93 2.5 11 .28 1.17 5.54
CM12-H1 12 8.5 60 1.98 4.34 2.5 3 .30 1.14 25.42
CM12-H2 12 8.5 60 2.64 5.79 2.5 4 .30 1.14 19.05
CM12-H3 12 8.5 60 3.30 7.24 2.5 5 .30 1.14 15.23
CM12-H4 12 8.5 60 3.99 8.69 2.5 6 .30 1.14 12.77
CM12-H5 12 8.5 60 4.65 10.13 2.5 7 .30 1.14 10.95
Product Dimensions CM12-H6 12 8.5 60 5.31 11.58 2.5 8 .30 1.14 9.57
All dimensions in millimeters CM12-H7 12 8.5 60 5.97 13.03 2.5 9 .30 1.14 8.50
unless otherwise specified. CM12-H8 12 8.5 60 6.63 14.48 2.5 10 .30 1.14 7.64
CM12-H9 12 8.5 60 7.29 15.93 2.5 11 .30 1.14 6.94
CM14-L1 14 10 22 2.18 4.95 2.5 3 .23 1.47 7.94
CM14-L2 14 10 22 2.95 6.60 2.5 4 .23 1.47 6.03
CM14-L3 14 10 22 3.71 8.26 2.5 5 .23 1.47 4.84
CM14-L4 14 10 22 4.52 9.91 2.5 6 .23 1.47 4.08
CM14-L5 14 10 22 5.33 11.56 2.5 7 .23 1.47 3.53
CM14-L6 14 10 22 6.17 13.21 2.5 8 .23 1.47 3.13
CM14-L7 14 10 22 7.01 14.86 2.5 9 .23 1.47 2.80
CM14-L8 14 10 22 7.85 16.51 2.5 10 .23 1.47 2.54
CM14-L9 14 10 22 8.71 18.16 2.5 11 .23 1.47 2.33
Plain Ends CM14-M1 14 10 50 2.18 4.95 2.5 3 .30 1.52 18.05
CM14-M2 14 10 50 2.95 6.60 2.5 4 .30 1.52 13.70
CM14-M3 14 10 50 3.71 8.26 2.5 5 .30 1.52 10.99
CM14-M4 14 10 50 4.52 9.91 2.5 6 .30 1.52 9.28
CM14-M5 14 10 50 5.33 11.56 2.5 7 .30 1.52 8.03
CM14-M6 14 10 50 6.17 13.21 2.5 8 .30 1.52 7.10
CM14-M7 14 10 50 7.01 14.86 2.5 9 .30 1.52 6.37
CM14-M8 14 10 50 7.85 16.51 2.5 10 .30 1.52 5.77
CM14-M9 14 10 50 8.71 18.16 2.5 11 .30 1.52 5.29
CM14-H1 14 9 80 3.15 4.95 2.5 3 .38 1.52 44.44
Shim Ends
CM14-H2 14 9 80 4.19 6.60 2.5 4 .38 1.52 33.20
CM14-H3 14 9 80 5.26 8.26 2.5 5 .38 1.52 26.67
CM14-H4 14 9 80 6.30 9.91 2.5 6 .38 1.52 22.16
CM14-H5 14 9 80 7.34 11.56 2.5 7 .38 1.52 18.96
CM14-H6 14 9 80 8.41 13.21 2.5 8 .38 1.52 16.67
CM14-H7 14 9 80 9.45 14.86 2.5 9 .38 1.52 14.79
CM14-H8 14 9 80 10.49 16.51 2.5 10 .38 1.52 13.29
CM14-H9 14 9 80 11.56 18.16 2.5 11 .38 1.52 12.12
CM15-L1 15 11 25 2.57 5.18 2.5 3 .25 1.47 9.58
CM15-L2 15 11 25 3.43 6.91 2.5 4 .25 1.47 7.18
CM15-L3 15 11 25 4.27 8.64 2.5 5 .25 1.47 5.72
CM15-L4 15 11 25 5.13 10.36 2.5 6 .25 1.47 4.78
CM15-L5 15 11 25 5.99 12.09 2.5 7 .25 1.47 4.10
CM15-L6 15 11 25 6.83 13.82 2.5 8 .25 1.47 3.58
CM15-L7 15 11 25 7.70 15.54 2.5 9 .25 1.47 3.19
Order Options CM15-L8
CM15-L9
15
15
11 25 8.53 17.27
11 25 9.40 19.00
2.5 10
2.5 11
.25
.25
1.47 2.86
1.47 2.60
CM 030-L1 CM15-M1
CM15-M2
15
15
10 50 3.43 5.18
10 50 4.57 6.91
3.5
3.5
3
4
.23
.23
1.47 28.57
1.47 21.37
CM15-M3 15 10 50 5.72 8.64 3.5 5 .23 1.47 17.12
CM15-M4 15 10 50 6.86 10.36 3.5 6 .23 1.47 14.29
End options: CM15-M5 15 10 50 8.00 12.09 3.5 7 .23 1.47 12.22
Plain ends . . . . . . . . . . . . CM CM15-M6 15 10 50 9.14 13.82 3.5 8 .23 1.47 10.68
Squared-shim ends . . . . . . CMS CM15-M7 15 10 50 10.29 15.54 3.5 9 .23 1.47 9.52
CM15-M8 15 10 50 11.43 17.27 3.5 10 .23 1.47 8.56
Material option: CM15-M9 15 10 50 12.57 19.00 3.5 11 .23 1.47 7.78
1
Use “CM” prefix for plain ends. Use “CMS” prefix for squared-shim ends.
2
3
4
smalley.com No-Tooling-Charges™ For Customs
5
32
CM/CMS Series

CM15-H1 15 10 80 3.20 5.18 3.5 3 .25 1.47 40.40
CM15-H2 15 10 80 4.19 6.91 3.5 4 .25 1.47 29.41
CM15-H3 15 10 80 5.23 8.64 3.5 5 .25 1.47 23.46
CM15-H4 15 10 80 6.27 10.36 3.5 6 .25 1.47 19.56
CM15-H5 15 10 80 7.32 12.09 3.5 7 .25 1.47 16.77
CM15-H6 15 10 80 8.36 13.82 3.5 8 .25 1.47 14.65
CM15-H7 15 10 80 9.40 15.54 3.5 9 .25 1.47 13.03
CM15-H8 15 10 80 10.46 17.27 3.5 10 .25 1.47 11.75
CM15-H9 15 10 80 11.51 19.00 3.5 11 .25 1.47 10.68
CM16-L1 16 11 25 2.11 5.41 2.5 3 .25 1.47 7.58
CM16-L2 16 11 25 2.79 7.21 2.5 4 .25 1.47 5.66
CM16-L3 16 11 25 3.51 9.02 2.5 5 .25 1.47 4.54
CM16-L4 16 11 25 4.19 10.82 2.5 6 .25 1.47 3.77
CM16-L5 16 11 25 4.90 12.62 2.5 7 .25 1.47 3.24
CM16-L6 16 11 25 6.30 16.23 2.5 9 .25 1.47 2.52 Product Dimensions
CM16-L7 16 11 25 7.70 19.84 2.5 11 .25 1.47 2.06 All dimensions in millimeters
CM16-L8 16 11 25 9.09 23.44 2.5 13 .25 1.47 1.74 unless otherwise specified.
CM16-M1 16 11 55 3.63 5.41 3.5 3 .25 1.47 30.90
CM16-M2 16 11 55 4.83 7.21 3.5 4 .25 1.47 23.11
CM16-M3 16 11 55 6.05 9.02 3.5 5 .25 1.47 18.52
CM16-M4 16 11 55 7.24 10.82 3.5 6 .25 1.47 15.36
CM16-M5 16 11 55 8.46 12.62 3.5 7 .25 1.47 13.22
CM16-M6 16 11 55 10.87 16.23 3.5 9 .25 1.47 10.26
CM16-M7 16 11 55 13.28 19.84 3.5 11 .25 1.47 8.38
CM16-M8 16 11 55 15.70 23.44 3.5 13 .25 1.47 7.11
CM16-H1 16 11 90 3.30 5.41 3.5 3 .30 1.52 42.65
CM16-H2 16 11 90 4.57 7.21 3.5 4 .30 1.52 34.09
CM16-H3 16 11 90 5.59 9.02 3.5 5 .30 1.52 26.24 Plain Ends
CM16-H4 16 11 90 6.86 10.82 3.5 6 .30 1.52 22.73
CM16-H5 16 11 90 7.87 12.62 3.5 7 .30 1.52 18.95
CM16-H6 16 11 90 10.16 16.23 3.5 9 .30 1.52 14.83
CM16-H7 16 11 90 12.45 19.84 3.5 11 .30 1.52 12.18
CM16-H8 16 11 90 14.73 23.44 3.5 13 .30 1.52 10.33
CM18-L1 18 13 30 3.63 5.72 3.5 3 .20 1.80 14.35
CM18-L2 18 13 30 4.75 7.62 3.5 4 .20 1.80 10.45
CM18-L3 18 13 30 5.94 9.53 3.5 5 .20 1.80 8.36
CM18-L4 18 13 30 7.14 11.43 3.5 6 .20 1.80 6.99
Shim Ends
CM18-L5 18 13 30 8.31 13.34 3.5 7 .20 1.80 5.96
CM18-L6 18 13 30 10.69 17.15 3.5 9 .20 1.80 4.64
CM18-L7 18 13 30 14.25 22.86 3.5 12 .20 1.80 3.48
CM18-M1 18 13 55 3.68 5.72 3.5 3 .25 1.83 26.96
CM18-M2 18 13 55 4.98 7.62 3.5 4 .25 1.83 20.83
CM18-M3 18 13 55 6.22 9.53 3.5 5 .25 1.83 16.62
CM18-M4 18 13 55 7.47 11.43 3.5 6 .25 1.83 13.89
CM18-M5 18 13 55 8.74 13.34 3.5 7 .25 1.83 11.96
CM18-M6 18 13 55 11.23 17.15 3.5 9 .25 1.83 9.29
CM18-M7 18 13 55 14.96 22.86 3.5 12 .25 1.83 6.96
CM18-H1 18 13 90 3.84 5.72 3.5 3 .30 1.83 47.87
CM18-H2 18 13 90 5.13 7.62 3.5 4 .30 1.83 36.14
CM18-H3 18 13 90 6.40 9.53 3.5 5 .30 1.83 28.75
CM18-H4 18 13 90 7.70 11.43 3.5 6 .30 1.83 24.13
CM18-H5 18 13 90 8.97 13.34 3.5 7 .30 1.83 20.59
CM18-H6
CM18-H7
18
18
13
13
90 11.53 17.15
90 15.37 22.86
3.5
3.5
9
12
.30
.30
1.83 16.01
1.83 12.02
Order Options
CM20-L1
CM20-L2
20
20
15
15
35 2.72 6.32
35 3.61 8.43
3.5
3.5
3
4
.20
.20
1.80 9.72
1.80 7.26 CM 030-L1
CM20-L3 20 15 35 4.52 10.54 3.5 5 .20 1.80 5.81
CM20-L4 20 15 35 5.41 12.65 3.5 6 .20 1.80 4.83
CM20-L5 20 15 35 6.32 14.76 3.5 7 .20 1.80 4.15 End options:
CM20-L6 20 15 35 8.13 18.97 3.5 9 .20 1.80 3.23 Plain ends . . . . . . . . . . . . CM
CM20-L7 20 15 35 10.82 25.30 3.5 12 .20 1.80 2.42 Squared-shim ends . . . . . . CMS
CM20-M1 20 14 70 3.05 6.32 3.5 3 .25 1.98 21.41
CM20-M2 20 14 70 4.06 8.43 3.5 4 .25 1.98 16.02 Material option:
CM20-M3 20 14 70 5.08 10.54 3.5 5 .25 1.98 12.82
1
Use “CM” prefix for plain ends. Use “CMS” prefix for squared-shim ends. Stainless Steel . . . . . . . . . -S17
2
3
4
5 Manufactured in USA Smalley (847) 719-5900 33

CM20-M4 20 14 70 6.27 12.65 3.5 6 .25 1.98 10.97
CM20-M5 20 14 70 7.32 14.76 3.5 7 .25 1.98 9.41
CM20-M6 20 14 70 9.17 18.97 3.5 9 .25 1.98 7.14
CM20-M7 20 14 70 12.22 25.30 3.5 12 .25 1.98 5.35
CM20-H1 20 14 100 4.24 6.32 3.5 3 .33 2.01 48.08
CM20-H2 20 14 100 5.66 8.43 3.5 4 .33 2.01 36.10
CM20-H3 20 14 100 7.06 10.54 3.5 5 .33 2.01 28.74
CM20-H4 20 14 100 8.48 12.65 3.5 6 .33 2.01 23.98
CM20-H5 20 14 100 9.91 14.76 3.5 7 .33 2.01 20.62
CM20-H6 20 14 100 12.73 18.97 3.5 9 .33 2.01 16.03
CM20-H7 20 14 100 16.97 25.30 3.5 12 .33 2.01 12.00
CM25-L1 25 19 50 2.06 6.63 3.5 3 .25 2.18 10.94
CM25-L2 25 19 50 2.74 8.84 3.5 4 .25 2.18 8.20
CM25-L3 25 19 50 3.43 11.05 3.5 5 .25 2.18 6.56
Product Dimensions CM25-L4 25 19 50 4.11 13.26 3.5 6 .25 2.18 5.46
All dimensions in millimeters CM25-L5 25 19 50 4.80 15.47 3.5 7 .25 2.18 4.69
unless otherwise specified. CM25-L6 25 19 50 6.20 19.89 3.5 9 .25 2.18 3.65
CM25-L7 25 19 50 8.26 26.52 3.5 12 .25 2.18 2.74
CM25-M1 25 19 80 2.95 6.63 3.5 3 .30 2.39 21.74
CM25-M2 25 19 80 3.94 8.84 3.5 4 .30 2.39 16.33
CM25-M3 25 19 80 4.90 11.05 3.5 5 .30 2.39 13.01
CM25-M4 25 19 80 5.89 13.26 3.5 6 .30 2.39 10.85
CM25-M5 25 19 80 6.88 15.47 3.5 7 .30 2.39 9.31
CM25-M6 25 19 80 8.84 19.89 3.5 9 .30 2.39 7.24
CM25-M7 25 19 80 11.79 26.52 3.5 12 .30 2.39 5.43
CM25-H1 25 19 110 4.04 6.63 3.5 3 .38 2.39 42.47
CM25-H2 25 19 110 5.38 8.84 3.5 4 .38 2.39 31.79
Plain Ends CM25-H3 25 19 110 6.73 11.05 3.5 5 .38 2.39 25.46
CM25-H4 25 19 110 8.08 13.26 3.5 6 .38 2.39 21.24
CM25-H5 25 19 110 9.40 15.47 3.5 7 .38 2.39 18.12
CM25-H6 25 19 110 12.12 19.89 3.5 9 .38 2.39 14.16
CM25-H7 25 19 110 16.15 26.52 3.5 12 .38 2.39 10.61
CM28-L1 28 22 50 3.76 7.24 3.5 3 .30 2.39 14.37
CM28-L2 28 22 50 5.00 9.65 3.5 4 .30 2.39 10.75
CM28-L3 28 22 50 6.27 12.07 3.5 5 .30 2.39 8.62
CM28-L4 28 22 50 7.52 14.48 3.5 6 .30 2.39 7.18
CM28-L5 28 22 50 8.79 16.89 3.5 7 .30 2.39 6.17
Shim Ends
CM28-L6 28 22 50 10.03 19.30 3.5 8 .30 2.39 5.39
CM28-L7 28 22 50 11.28 21.72 3.5 9 .30 2.39 4.79
CM28-L8 28 22 50 13.79 26.54 3.5 11 .30 2.39 3.92
CM28-L9 28 22 50 16.31 31.37 3.5 13 .30 2.39 3.32
CM28-M1 28 22 80 4.39 7.24 3.5 3 .38 2.39 28.07
CM28-M2 28 22 80 5.84 9.65 3.5 4 .38 2.39 21.00
CM28-M3 28 22 80 7.32 12.07 3.5 5 .38 2.39 16.84
CM28-M4 28 22 80 8.79 14.48 3.5 6 .38 2.39 14.06
CM28-M5 28 22 80 10.24 16.89 3.5 7 .38 2.39 12.03
CM28-M6 28 22 80 11.71 19.30 3.5 8 .38 2.39 10.54
CM28-M7 28 22 80 13.18 21.72 3.5 9 .38 2.39 9.37
CM28-M8 28 22 80 16.10 26.54 3.5 11 .38 2.39 7.66
CM28-M9 28 22 80 19.02 31.37 3.5 13 .38 2.39 6.48
CM28-H1 28 22 130 4.57 7.24 3.5 3 .46 2.39 48.69
CM28-H2 28 22 130 6.07 9.65 3.5 4 .46 2.39 36.31
Order Options CM28-H3
CM28-H4
28
28
22 130 7.59 12.07
22 130 9.12 14.48
3.5
3.5
5
6
.46
.46
2.39 29.02
2.39 24.25
CM 030-L1 CM28-H5
CM28-H6
28
28
22 130 10.64 16.89
22 130 12.17 19.30
3.5
3.5
7
8
.46
.46
2.39 20.80
2.39 18.23
CM28-H7 28 22 130 13.69 21.72 3.5 9 .46 2.39 16.19
CM28-H8 28 22 130 16.71 26.54 3.5 11 .46 2.39 13.22
End options: CM28-H9 28 22 130 19.76 31.37 3.5 13 .46 2.39 11.20
Plain ends . . . . . . . . . . . . CM CM30-L1 30 24 50 3.18 7.62 3.5 3 .30 2.39 11.26
Squared-shim ends . . . . . . CMS CM30-L2 30 24 50 4.22 10.16 3.5 4 .30 2.39 8.42
CM30-L3 30 24 50 5.28 12.70 3.5 5 .30 2.39 6.74
Material option: CM30-L4 30 24 50 6.32 15.24 3.5 6 .30 2.39 5.61
CM30-L5 30 24 50 7.39 17.78 3.5 7 .30 2.39 4.81
Use “CM” prefix for plain ends. Use “CMS” prefix for squared-shim ends.
2
3
4
34 smalley.com 5
See pages 132-133 for How to Order. No-Tooling-Charges™ For Customs
CM/CMS Series

CM30-L6 30 24 50 8.43 20.32 3.5 8 .30 2.39 4.21
CM30-L7 30 24 50 9.50 22.86 3.5 9 .30 2.39 3.74
CM30-L8 30 24 50 11.61 27.94 3.5 11 .30 2.39 3.06
CM30-L9 30 24 50 13.72 33.02 3.5 13 .30 2.39 2.59
CM30-M1 30 24 90 3.51 7.62 3.5 3 .38 2.39 21.90
CM30-M2 30 24 90 4.70 10.16 3.5 4 .38 2.39 16.48
CM30-M3 30 24 90 5.87 12.70 3.5 5 .38 2.39 13.18
CM30-M4 30 24 90 7.04 15.24 3.5 6 .38 2.39 10.98
CM30-M5 30 24 90 8.20 17.78 3.5 7 .38 2.39 9.39
CM30-M6 30 24 90 9.37 20.32 3.5 8 .38 2.39 8.22
CM30-M7 30 24 90 10.54 22.86 3.5 9 .38 2.39 7.31
CM30-M8 30 24 90 12.90 27.94 3.5 11 .38 2.39 5.98
CM30-M9 30 24 90 15.24 33.02 3.5 13 .38 2.39 5.06
CM30-H1 30 24 130 4.19 7.62 3.5 3 .46 2.39 37.90
CM30-H2 30 24 130 5.59 10.16 3.5 4 .46 2.39 28.45 Product Dimensions
CM30-H3 30 24 130 6.99 12.70 3.5 5 .46 2.39 22.77 All dimensions in millimeters
CM30-H4 30 24 130 8.38 15.24 3.5 6 .46 2.39 18.95 unless otherwise specified.
CM30-H5 30 24 130 9.78 17.78 3.5 7 .46 2.39 16.25
CM30-H6 30 24 130 11.18 20.32 3.5 8 .46 2.39 14.22
CM30-H7 30 24 130 12.57 22.86 3.5 9 .46 2.39 12.63
CM30-H8 30 24 130 15.37 27.94 3.5 11 .46 2.39 10.34
CM30-H9 30 24 130 18.16 33.02 3.5 13 .46 2.39 8.75
CM35-L1 35 27 70 3.94 8.38 3.5 3 .36 3.18 15.77
CM35-L2 35 27 70 5.23 11.18 3.5 4 .36 3.18 11.76
CM35-L3 35 27 70 6.55 13.97 3.5 5 .36 3.18 9.43
CM35-L4 35 27 70 7.87 16.76 3.5 6 .36 3.18 7.87
CM35-L5 35 27 70 9.17 19.56 3.5 7 .36 3.18 6.74
CM35-L6 35 27 70 10.49 22.35 3.5 8 .36 3.18 5.90 Plain Ends
CM35-L7 35 27 70 11.81 25.15 3.5 9 .36 3.18 5.25
CM35-L8 35 27 70 14.43 30.73 3.5 11 .36 3.18 4.29
CM35-L9 35 27 70 17.04 36.32 3.5 13 .36 3.18 3.63
CM35-M1 35 27 110 4.14 8.38 3.5 3 .41 3.38 25.94
CM35-M2 35 27 110 5.51 11.18 3.5 4 .41 3.38 19.40
CM35-M3 35 27 110 6.88 13.97 3.5 5 .41 3.38 15.51
CM35-M4 35 27 110 8.26 16.76 3.5 6 .41 3.38 12.94
CM35-M5 35 27 110 9.63 19.56 3.5 7 .41 3.38 11.08
CM35-M6 35 27 110 11.02 22.35 3.5 8 .41 3.38 9.71
Shim Ends
CM35-M7 35 27 110 12.40 25.15 3.5 9 .41 3.38 8.63
CM35-M8 35 27 110 15.14 30.73 3.5 11 .41 3.38 7.06
CM35-M9 35 27 110 17.91 36.32 3.5 13 .41 3.38 5.98
CM35-H1 35 27 160 4.04 8.38 3.5 3 .46 3.38 36.87
CM35-H2 35 27 160 5.38 11.18 3.5 4 .46 3.38 27.59
CM35-H3 35 27 160 6.73 13.97 3.5 5 .46 3.38 22.10
CM35-H4 35 27 160 8.08 16.76 3.5 6 .46 3.38 18.43
CM35-H5 35 27 160 9.42 19.56 3.5 7 .46 3.38 15.78
CM35-H6 35 27 160 10.77 22.35 3.5 8 .46 3.38 13.82
CM35-H7 35 27 160 12.12 25.15 3.5 9 .46 3.38 12.28
CM35-H8 35 27 160 14.81 30.73 3.5 11 .46 3.38 10.05
CM35-H9 35 27 160 17.50 36.32 3.5 13 .46 3.38 8.50
CM40-L1 40 30 100 2.90 9.14 3.5 3 .41 3.38 16.03
CM40-L2 40 30 100 3.86 12.19 3.5 4 .41 3.38 12.00
CM40-L3 40 30 100 4.80 15.24 3.5 5 .41 3.38 9.58
CM40-L4
CM40-L5
40
40
30
30
100 5.77 18.29
100 6.73 21.34
3.5
3.5
6
7
.41
.41
3.38 7.99
3.38 6.84
Order Options
CM40-L6
CM40-L7
40
40
30
30
100 7.70 24.38
100 8.66 27.43
3.5
3.5
8
9
.41
.41
3.38 6.00
3.38 5.33 CM 030-L1
CM40-L8 40 30 100 10.59 33.53 3.5 11 .41 3.38 4.36
CM40-L9 40 30 100 12.52 39.62 3.5 13 .41 3.38 3.69
CM40-M1 40 30 150 5.44 9.14 3.5 3 .53 3.63 40.54 End options:
CM40-M2 40 30 150 7.24 12.19 3.5 4 .53 3.63 30.30 Plain ends . . . . . . . . . . . . CM
CM40-M3 40 30 150 9.04 15.24 3.5 5 .53 3.63 24.19 Squared-shim ends . . . . . . CMS
CM40-M4 40 30 150 10.85 18.29 3.5 6 .53 3.63 20.16
CM40-M5 40 30 150 12.65 21.34 3.5 7 .53 3.63 17.26 Material option:
1
Use “CM” prefix for plain ends. Use “CMS” prefix for squared-shim ends. Stainless Steel . . . . . . . . . -S17
2
3
4
5
CM40-M6 40 30 150 14.48 24.38 3.5 8 .53 3.63 15.15
CM40-M7 40 30 150 16.28 27.43 3.5 9 .53 3.63 13.45
CM40-M8 40 30 150 19.89 33.53 3.5 11 .53 3.63 11.00
CM40-M9 40 30 150 23.50 39.62 3.5 13 .53 3.63 9.31
CM40-H1 40 30 300 5.66 9.14 4.5 3 .46 3.38 86.21
CM40-H2 40 30 300 7.54 12.19 4.5 4 .46 3.38 64.52
CM40-H3 40 30 300 9.42 15.24 4.5 5 .46 3.38 51.55
CM40-H4 40 30 300 11.33 18.29 4.5 6 .46 3.38 43.10
CM40-H5 40 30 300 13.21 21.34 4.5 7 .46 3.38 36.90
CM40-H6 40 30 300 15.09 24.38 4.5 8 .46 3.38 32.29
CM40-H7 40 30 300 16.97 27.43 4.5 9 .46 3.38 28.68
CM40-H8 40 30 300 20.75 33.53 4.5 11 .46 3.38 23.47
CM40-H9 40 30 300 24.54 39.62 4.5 13 .46 3.38 19.89
CM45-L1 45 35 110 3.38 9.91 3.5 3 .46 3.63 16.85
CM45-L2 45 35 110 4.52 13.21 3.5 4 .46 3.63 12.66
Product Dimensions CM45-L3 45 35 110 5.64 16.51 3.5 5 .46 3.63 10.12
All dimensions in millimeters CM45-L4 45 35 110 6.76 19.81 3.5 6 .46 3.63 8.43
unless otherwise specified. CM45-L5 45 35 110 7.90 23.11 3.5 7 .46 3.63 7.23
CM45-L6 45 35 110 9.02 26.42 3.5 8 .46 3.63 6.32
CM45-L7 45 35 110 10.16 29.72 3.5 9 .46 3.63 5.62
CM45-L8 45 35 110 12.40 36.32 3.5 11 .46 3.63 4.60
CM45-L9 45 35 110 14.66 42.93 3.5 13 .46 3.63 3.89
CM45-M1 45 35 225 5.33 9.91 4.5 3 .46 3.63 49.13
CM45-M2 45 35 225 6.99 13.21 4.5 4 .46 3.63 36.17
CM45-M3 45 35 225 9.14 16.51 4.5 5 .46 3.63 30.53
CM45-M4 45 35 225 10.80 19.81 4.5 6 .46 3.63 24.97
CM45-M5 45 35 225 12.70 23.11 4.5 7 .46 3.63 21.61
CM45-M6 45 35 225 14.48 26.42 4.5 8 .46 3.63 18.84
Plain Ends CM45-M7 45 35 225 16.26 29.72 4.5 9 .46 3.63 16.72
CM45-M8 45 35 225 19.81 36.32 4.5 11 .46 3.63 13.63
CM45-M9 45 35 225 23.37 42.93 4.5 13 .46 3.63 11.50
CM45-H1 45 35 400 6.43 9.91 4.5 3 .61 3.76 114.94
CM45-H2 45 35 400 8.38 13.21 4.5 4 .61 3.76 82.82
CM45-H3 45 35 400 11.20 16.51 4.5 5 .61 3.76 75.33
CM45-H4 45 35 400 12.95 19.81 4.5 6 .61 3.76 58.31
CM45-H5 45 35 400 15.37 23.11 4.5 7 .61 3.76 51.68
CM45-H6 45 35 400 17.27 26.42 4.5 8 .61 3.76 43.72
CM45-H7 45 35 400 19.68 29.72 4.5 9 .61 3.76 39.88
Shim Ends CM45-H8 45 35 400 24.26 36.32 4.5 11 .61 3.76 33.17
CM45-H9 45 35 400 28.45 42.93 4.5 13 .61 3.76 27.62
CM50-L1 50 40 110 4.83 10.29 3.5 3 .53 3.63 20.15
CM50-L2 50 40 110 6.10 13.72 3.5 4 .53 3.63 14.44
CM50-L3 50 40 110 7.87 17.15 3.5 5 .53 3.63 11.85
CM50-L4 50 40 110 9.40 20.57 3.5 6 .53 3.63 9.85
CM50-L5 50 40 110 11.30 24.00 3.5 7 .53 3.63 8.66
CM50-L6 50 40 110 12.70 27.43 3.5 8 .53 3.63 7.47
CM50-L7 50 40 110 14.99 30.86 3.5 9 .53 3.63 6.93
CM50-L8 50 40 110 18.16 37.72 3.5 11 .53 3.63 5.62
CM50-L9 50 40 110 21.34 44.58 3.5 13 .53 3.63 4.73
CM50-L10 50 40 110 24.64 51.44 3.5 15 .53 3.63 4.10
CM50-M1 50 40 225 4.62 10.29 4.5 3 .46 3.63 39.68
CM50-M2 50 40 225 5.84 13.72 4.5 4 .46 3.63 30.53
CM50-M3 50 40 225 7.49 17.15 4.5 5 .46 3.63 23.29
Order Options CM50-M4
CM50-M5
50
50
40
40
225 8.89 20.57
225 10.54 24.00
4.5
4.5
6
7
.46
.46
3.63 19.26
3.63 16.72
CM50-M6 50 40 225 11.89 27.43 4.5 8 .46 3.63 14.48
CM 030-L1 CM50-M7 50 40 225 13.59 30.86 4.5 9 .46 3.63 13.03
CM50-M8 50 40 225 16.71 37.72 4.5 11 .46 3.63 10.71
CM50-M9 50 40 225 19.61 44.58 4.5 13 .46 3.63 9.01
End options: CM50-M10 50 40 225 22.48 51.44 4.5 15 .46 3.63 7.77
Plain ends . . . . . . . . . . . . CM CM50-H1 50 40 400 5.92 10.29 4.5 3 .61 3.76 91.53
Squared-shim ends . . . . . . CMS CM50-H2 50 40 400 7.80 13.72 4.5 4 .61 3.76 67.57
CM50-H3 50 40 400 10.16 17.15 4.5 5 .61 3.76 57.22
CM50-H4 50 40 400 11.79 20.57 4.5 6 .61 3.76 45.56
Material option: CM50-H5 50 40 400 14.15 24.00 4.5 7 .61 3.76 40.61
Carbon Steel . . . . . . . . (blank) CM50-H6 50 40 400 15.62 27.43 4.5 8 .61 3.76 33.87
1
Use “CM” prefix for plain ends. Use “CMS” prefix for 4
squared-shim ends. 5
2
36 smalley.com 3
Reference dimension. No-Tooling-Charges™ For Customs
CM/CMS Series
CM50-H7 50 40 400 17.91 30.86 4.5 9 .61 3.76 30.89
CM50-H8 50 40 400 21.54 37.72 4.5 11 .61 3.76 24.72
CM50-H9 50 40 400 25.65 44.58 4.5 13 .61 3.76 21.13
CM50-H10 50 40 400 29.21 51.44 4.5 15 .61 3.76 17.99
CM55-L1 55 45 125 5.59 11.05 3.5 3 .61 3.76 22.89
CM55-L2 55 45 125 7.72 14.73 3.5 4 .61 3.76 17.83
CM55-L3 55 45 125 9.68 18.41 3.5 5 .61 3.76 14.30
CM55-L4 55 45 125 11.48 22.10 3.5 6 .61 3.76 11.77
CM55-L5 55 45 125 13.92 25.78 3.5 7 .61 3.76 10.54
CM55-L6 55 45 125 15.52 29.46 3.5 8 .61 3.76 8.97
CM55-L7 55 45 125 18.41 33.15 3.5 9 .61 3.76 8.49
CM55-L8 55 45 125 21.67 40.51 3.5 11 .61 3.76 6.63
CM55-L9 55 45 125 25.65 47.88 3.5 13 .61 3.76 5.62
CM55-L10 55 45 125 29.77 55.25 3.5 15 .61 3.76 4.91
CM55-M1 55 45 250 3.10 11.05 4.5 3 .46 3.63 31.45
CM55-M2 55 45 250 4.11 14.73 4.5 4 .46 3.63 23.54 Product Dimensions
CM55-M3 55 45 250 5.16 18.41 4.5 5 .46 3.63 18.85 All dimensions in millimeters
CM55-M4 55 45 250 6.20 22.10 4.5 6 .46 3.63 15.72 unless otherwise specified.
CM55-M5 55 45 250 7.21 25.78 4.5 7 .46 3.63 13.46
CM55-M6 55 45 250 8.26 29.46 4.5 8 .46 3.63 11.79
CM55-M7 55 45 250 9.27 33.15 4.5 9 .46 3.63 10.47
CM55-M8 55 45 250 11.33 40.51 4.5 11 .46 3.63 8.57
CM55-M9 55 45 250 13.41 47.88 4.5 13 .46 3.63 7.25
CM55-M10 55 45 250 15.47 55.25 4.5 15 .46 3.63 6.28
CM55-H1 55 45 400 5.31 11.05 4.5 3 .61 3.76 69.69
CM55-H2 55 45 400 7.24 14.73 4.5 4 .61 3.76 53.40
CM55-H3 55 45 400 9.09 18.41 4.5 5 .61 3.76 42.87
CM55-H4 55 45 400 10.64 22.10 4.5 6 .61 3.76 34.90
CM55-H5 55 45 400 12.24 25.78 4.5 7 .61 3.76 29.54 Plain Ends
CM55-H6 55 45 400 14.10 29.46 4.5 8 .61 3.76 26.04
CM55-H7 55 45 400 15.82 33.15 4.5 9 .61 3.76 23.08
CM55-H8 55 45 400 19.30 40.51 4.5 11 .61 3.76 18.86
CM55-H9 55 45 400 23.11 47.88 4.5 13 .61 3.76 16.15
CM55-H10 55 45 400 26.54 55.25 4.5 15 .61 3.76 13.93
CM60-L1 60 50 135 5.59 11.43 4.5 3 .46 3.63 23.12
CM60-L2 60 50 135 7.47 15.24 4.5 4 .46 3.63 17.37
CM60-L3 60 50 135 9.32 19.05 4.5 5 .46 3.63 13.87
CM60-L4 60 50 135 11.20 22.86 4.5 6 .46 3.63 11.58
CM60-L5 60 50 135 13.06 26.67 4.5 7 .46 3.63 9.92 Shim Ends
CM60-L6 60 50 135 14.94 30.48 4.5 8 .46 3.63 8.69
CM60-L7 60 50 135 16.79 34.29 4.5 9 .46 3.63 7.71
CM60-L8 60 50 135 20.52 41.91 4.5 11 .46 3.63 6.31
CM60-L9 60 50 135 24.26 49.53 4.5 13 .46 3.63 5.34
CM60-L10 60 50 135 27.99 57.15 4.5 15 .46 3.63 4.63
CM60-M1 60 50 275 6.65 11.43 4.5 3 .61 3.76 57.53
CM60-M2 60 50 275 8.86 15.24 4.5 4 .61 3.76 43.10
CM60-M3 60 50 275 11.07 19.05 4.5 5 .61 3.76 34.46
CM60-M4 60 50 275 13.28 22.86 4.5 6 .61 3.76 28.71
CM60-M5 60 50 275 15.49 26.67 4.5 7 .61 3.76 24.60
CM60-M6 60 50 275 17.70 30.48 4.5 8 .61 3.76 21.52
CM60-M7 60 50 275 19.94 34.29 4.5 9 .61 3.76 19.16
CM60-M8 60 50 275 24.36 41.91 4.5 11 .61 3.76 15.67
CM60-M9 60 50 275 28.78 49.53 4.5 13 .61 3.76 13.25
CM60-M10
CM60-H1
60
60
50
50
275 33.22 57.15
450 7.75 11.43
4.5
4.5
15
3
.61
.76
3.76 11.49
4.01 122.28 Order Options
CM60-H2 60 50 450 10.31 15.24 4.5 4 .76 4.01 91.28
CM60-H3 60 50 450 12.90 19.05 4.5 5 .76 4.01 73.17 CM 030-L1
CM60-H4 60 50 450 15.47 22.86 4.5 6 .76 4.01 60.89
CM60-H5 60 50 450 18.06 26.67 4.5 7 .76 4.01 52.26
CM60-H6 60 50 450 20.62 30.48 4.5 8 .76 4.01 45.64 End options:
CM60-H7 60 50 450 23.22 34.29 4.5 9 .76 4.01 40.65 Plain ends . . . . . . . . . . . . CM
CM60-H8 60 50 450 28.37 41.91 4.5 11 .76 4.01 33.23 Squared-shim ends . . . . . . CMS
CM60-H9 60 50 450 33.53 49.53 4.5 13 .76 4.01 28.13
CM60-H10 60 50 450 38.68 57.15 4.5 15 .76 4.01 24.36
Material option:
1
Use “CM” prefix for plain ends. Use “CMS” prefix for 4
Theoretical dimension; measured in N/mm. Carbon Steel . . . . . . . . (blank)
squared-shim ends. 5
See pages 132-133 for How to Order. Stainless Steel . . . . . . . . . -S17
2
3

LS Series
LS Series - Linear Springs Linear Springs
LS Series Linear Spri
WIDTH
LENGTH Smalley Linear Springs
WIDTH Smalley Linear Springs are a continuous wave formed (marcelled)
wire length produced from spring tempered
LENGTH Smalley Linear
materials. TheySprings
act as a
MULTI-WAVE
Smalley Linear Springs
load bearing device having approximately the same load/deflection are a continuous wave formed (marcelled)
characteristics as a wave spring. Axial pressure is obtained by laying spring tempered materials. They act as a
wire length produced from
(SEE TABLE)
the expander flat inMULTI-WAVE

a straight load bearing device having approximately the same load/deflection
(SEE TABLE) line.
FREE THICKNESS characteristics as a wave spring. Axial pressure is obtained by laying
WORK HEIGHT the expander flat in a straight line.
HEIGHT
FREE THICKNESS
WORK HEIGHT
HEIGHT
Product Dimensions
Smalley Part Number of Free Load Work Spring
Number1 Waves Thickness Width Length Height2 (lb) Product
HeightDimensionsRate3
LS12188-1 1 Smalley Part 0.188Number of 1.500
0.012 0.225 1.5 0.125 Free 2 11 Load Work Spring
LS12188-2 2 Number
0.012
1
0.188 Waves 3.000 Thickness0.225 Width 5.6 Length 0.125 Height 91 (lb) Height Rate3
LS12188-3 3 LS12188-1 0.188
0.012 1 4.500 0.012 0.225 0.188 10.4 1.500 0.125 0.225 136 1.5 0.125 11
LS12188-4 4 LS12188-2 0.188
0.012 2 6.000 0.012 0.225 0.188 14.8 3.000 0.125 0.225 182 5.6 0.125 91
LS12250-1 1 LS12188-3 0.250
0.012 3 1.500 0.012 0.225 0.188 2.2 4.500 0.125 0.225 15 10.4 0.125 136
LS12250-2 2 LS12188-4 0.250
0.012 4 3.000 0.012 0.225 0.188 7.8 6.000 0.125 0.225 121 14.8 0.125 182
LS12250-3 3 LS12250-1 0.250
0.012 1 4.500 0.012 0.225 0.250 13.9 1.500 0.125 0.225 181 2.2 0.125 15
LS12250-4 4 LS12250-2 0.250
0.012 2 6.000 0.012 0.225 0.250 19.8 3.000 0.125 0.225 242 7.8 0.125 121
LS12312-1 1 LS12250-3 0.312
0.012 3 1.500 0.012 0.225 0.250 2.9 4.500 0.125 0.225 19 13.9 0.125 181
LS12312-2 2 LS12250-4 0.312
0.012 4 3.000 0.012 0.225 0.250 10.2 6.000 0.125 0.225 151 19.8 0.125 242
LS12312-3 3 LS12312-1 0.312
0.012 1 4.500 0.012 0.225 0.312 17.6 1.500 0.125 0.225 226 2.9 0.125 19
LS12312-4 4 LS12312-2 0.312
0.012 2 6.000 0.012 0.225 0.312 26.0 3.000 0.125 0.225 302 10.2 0.125 151
LS12375-1 1 LS12312-3 0.375
0.012 3 1.500 0.012 0.225 0.312 3.5 4.500 0.125 0.225 23 17.6 0.125 226
LS12375-2 2 LS12312-4 0.375
0.012 4 3.000 0.012 0.225 0.312 11.3 6.000 0.125 0.225 181 26.0 0.125 302
LS12375-3 3 LS12375-1 0.375
0.012 1 4.500 0.012 0.225 0.375 20.1 1.500 0.125 0.225 272 3.5 0.125 23
LS12375-4 4 LS12375-2 0.375
0.012 2 6.000 0.012 0.225 0.375 25.2 3.000 0.125 0.225 362 11.3 0.125 181
LS20188-1 1 LS12375-3 0.188
0.020 3 1.875 0.012 0.250 0.375 3.0 4.500 0.150 0.225 27 20.1 0.125 272
LS20188-2 2 LS12375-4 0.188
0.020 4 3.750 0.012 0.250 0.375 11.4 6.000 0.150 0.225 215 25.2 0.125 362
LS20188-3 3 0.020
LS20188-1 0.188 1 5.625 0.020 0.250 0.188 23.5 1.875 0.150 0.250 323 3.0 0.150 27
LS20188-4 4 LS20188-2 0.188
0.020 2 7.500 0.020 0.250 0.188 32.5 3.750 0.150 0.250 431 11.4 0.150 215
LS20250-1 1 LS20188-3 0.250
0.020 3 1.875 0.020 0.250 0.188 5.6 5.625 0.150 0.250 36 23.5 0.150 323
LS20250-2 2 LS20188-4 0.250
0.020 4 3.750 0.020 0.250 0.188 17.6 7.500 0.150 0.250 286 32.5 0.150 431
LS20250-3 3 LS20250-1 0.250
0.020 1 5.625 0.020 0.250 0.250 31.7 1.875 0.150 0.250 430 5.6 0.150 36
LS20250-4 4 LS20250-2 0.250
0.020 2 7.500 0.020 0.250 0.250 44.9 3.750 0.150 0.250 573 17.6 0.150 286
LS20312-1 1 LS20250-3 0.312
0.020 3 1.875 0.020 0.250 0.250 6.0 5.625 0.150 0.250 45 31.7 0.150 430
LS20312-2 2 LS20250-4 0.312
0.020 4 3.750 0.020 0.250 0.250 20.5 7.500 0.150 0.250 357 44.9 0.150 573
LS20312-3 3 LS20312-1 0.312
0.020 1 5.625 0.020 0.250 0.312 34.9 1.875 0.150 0.250 536 6.0 0.150 45
LS20312-4 4 LS20312-2 0.312
0.020 2 7.500 0.020 0.250 0.312 50.8 3.750 0.150 0.250 715 20.5 0.150 357
LS20375-1 1 LS20312-3 0.375
0.020 3 1.875 0.020 0.250 0.312 6.4 5.625 0.150 0.250 54 34.9 0.150 536
LS20375-2 2 LS20312-4 0.375
0.020 4 3.750 0.020 0.250 0.312 23.3 7.500 0.150 0.250 430 50.8 0.150 715
LS20375-3 3 LS20375-1 0.375
0.020 1 5.625 0.020 0.250 0.375 52.0 1.875 0.150 0.250 644 6.4 0.150 54
LS20375-4 4 0.020
LS20375-2 0.375 2 7.500 0.020 0.250 0.375 74.5 3.750 0.150 0.250 859 23.3 0.150 430
LS25188-1 1 LS20375-3 0.188
0.025 3 2.250 0.020 0.275 0.375 3.5 5.625 0.175 0.250 30 52.0 0.150 644
LS25188-2 2 LS20375-4 0.188
0.025 4 4.500 0.020 0.275 0.375 15.4 7.500 0.175 0.250 243 74.5 0.150 859
LS25188-3 3 0.025
LS25188-1 0.188 1 6.750 0.025 0.275 0.188 27.9 2.250 0.175 0.275 365 3.5 0.175 30
LS25188-4 4 LS25188-2 0.188
0.025 2 9.000 0.025 0.275 0.188 42.5 4.500 0.175 0.275 487 15.4 0.175 243
LS25250-1 1 LS25188-3 0.250
0.025 3 2.250 0.025 0.275 0.188 6.5 6.750 0.175 0.275 40 27.9 0.175 365
LS25250-2 2 LS25188-4 0.250
0.025 4 4.500 0.025 0.275 0.188 21.7 9.000 0.175 0.275 324 42.5 0.175 487
LS25250-3 3 LS25250-1 0.250
0.025 1 6.750 0.025 0.275 0.250 34.7 2.250 0.175 0.275 486 6.5 0.175 40
LS25250-4 4 LS25250-2 0.250
0.025 2 9.000 0.025 0.275 0.250 50.5 4.500 0.175 0.275 647 21.7 0.175 324
LS25312-1 1 LS25250-3 0.312
0.025 3 2.250 0.025 0.275 0.250 6.6 6.750 0.175 0.275 51 34.7 0.175 486
LS25312-2 2 LS25250-4 0.312
0.025 4 4.500 0.025 0.275 0.250 24.0 9.000 0.175 0.275 404 50.5 0.175 647
LS25312-3 3 LS25312-1 0.312
0.025 1 6.750 0.025 0.275 0.312 43.2 2.250 0.175 0.275 606 6.6 0.175 51
LS25312-4 4 LS25312-2 0.312
0.025 2 9.000 0.025 0.275 0.312 62.0 4.500 0.175 0.275 808 24.0 0.175 404
LS25375-1 1 LS25312-3 0.375
0.025 3 2.250 0.025 0.275 0.312 7.7 6.750 0.175 0.275 61 43.2 0.175 606
LS25375-2 2 LS25312-4 0.375
0.025 4 4.500 0.025 0.275 0.312 29.4 9.000 0.175 0.275 486 62.0 0.175 808
LS25375-3 3 LS25375-1 0.375
0.025 1 6.750 0.025 0.275 0.375 53.8 2.250 0.175 0.275 728 7.7 0.175 61
LS25375-4 4 0.025
LS25375-2 0.375 2 9.000 0.025 0.275 0.375 76.9 4.500 0.175 0.275 971 29.4 0.175 486
LS25375-3 3 0.025 0.375 6.750 0.275 53.8 0.175 728
1
LS25375-4 4 0.025 0.375 9.000 0.275 76.9 0.175 971
2
3
Theoretical dimension; measured1in lb/in.
2
3
40 www.smalley.com No-Tooling-Charges™ For Specials

40 www.smalley.com No-Tooling-Charges™ For
LS Series
LS Series
Product Dimensions
Smalley Part Number of Free Load Work Spring
Number1 Waves Thickness Width Length Height2 (lb) Height Rate3
LS38188-1 1 0.038 0.188 2.625 0.300 7.5 0.200 67
LS38188-2 2 0.038 0.188 5.250 0.300 25.0 0.200 538
LS38188-3 3 0.038 0.188 7.875 0.300 61.0 0.200 808
LS38188-4 4 0.038 0.188 10.500 0.300 90.0 0.200 1077
LS38250-1 1 0.038 0.250 2.625 0.300 11.9 0.200 89
LS38250-2 2 0.038 0.250 5.250 0.300 45.7 0.200 716
LS38250-3 3 0.038 0.250 7.875 0.300 74.3 0.200 1074
LS38250-4 4 0.038 0.250 10.500 0.300 111.5 0.200 1432
LS38312-1 1 0.038 0.312 2.625 0.300 9.9 0.200 112
LS38312-2 2 0.038 0.312 5.250 0.300 49.3 0.200 893
LS38312-3 3 0.038 0.312 7.875 0.300 88.0 0.200 1340
LS38312-4 4 0.038 0.312 10.500 0.300 160.7 0.200 1787
LS38375-1 1 0.038 0.375 2.625 0.300 16.9 0.200 134
LS38375-2 2 0.038 0.375 5.250 0.300 61.7 0.200 1074
LS38375-3 3 0.038 0.375 7.875 0.300 105.0 0.200 1611
LS38375-4 4 0.038 0.375 10.500 0.300 153.0 0.200 2148
LS45188-1 1 0.045 0.188 3.000 0.325 9.0 0.225 75
LS45188-2 2 0.045 0.188 6.000 0.325 36.0 0.225 599
LS45188-3 3 0.045 0.188 9.000 0.325 65.0 0.225 898
LS45188-4 4 0.045 0.188 12.000 0.325 89.0 0.225 1198
LS45250-1 1 0.045 0.250 3.000 0.325 12.5 0.225 100
LS45250-2 2 0.045 0.250 6.000 0.325 42.5 0.225 797
LS45250-3 3 0.045 0.250 9.000 0.325 83.0 0.225 1195
LS45250-4 4 0.045 0.250 12.000 0.325 120.5 0.225 1593
LS45312-1 1 0.045 0.312 3.000 0.325 14.7 0.225 124
LS45312-2 2 0.045 0.312 6.000 0.325 60.3 0.225 994
LS45312-3 3 0.045 0.312 9.000 0.325 108.9 0.225 1491
LS45312-4 4 0.045 0.312 12.000 0.325 131.0 0.225 1988
LS45375-1 1 0.045 0.375 3.000 0.325 20.4 0.225 149
LS45375-2 2 0.045 0.375 6.000 0.325 73.1 0.225 1195
LS45375-3 3 0.045 0.375 9.000 0.325 133.5 0.225 1792
LS45375-4 4 0.045 0.375 12.000 0.325 190.0 0.225 2390
LS62188-1 1 0.062 0.188 3.375 0.350 14.3 0.250 138
LS62188-2 2 0.062 0.188 6.750 0.350 67.5 0.250 1100
LS62188-3 3 0.062 0.188 10.125 0.350 105.5 0.250 1650
LS62188-4 4 0.062 0.188 12.000 0.350 159.5 0.250 2200
LS62250-1 1 0.062 0.250 3.375 0.350 22.5 0.250 183
LS62250-2 2 0.062 0.250 6.750 0.350 104.0 0.250 1463
LS62250-3 3 0.062 0.250 10.125 0.350 161.0 0.250 2195
LS62250-4 4 0.062 0.250 12.000 0.350 234.0 0.250 2926
LS62312-1 1 0.062 0.312 3.375 0.350 27.8 0.250 228
LS62312-2 2 0.062 0.312 6.750 0.350 104.0 0.250 1826
LS62312-3 3 0.062 0.312 10.125 0.350 174.5 0.250 2739
LS62312-4 4 0.062 0.312 12.000 0.350 262.5 0.250 3652
LS62375-1 1 0.062 0.375 3.375 0.350 42.0 0.250 274
LS62375-2 2 0.062 0.375 6.750 0.350 139.5 0.250 2195
LS62375-3 3 0.062 0.375 10.125 0.350 240.0 0.250 3292
LS62375-4 4 0.062 0.375 12.000 0.350 353.0 0.250 4389
1
2
3
Rotary Vane Pump

Smalley Linear Springs are used to radially load
the bottom of the vanes in the pump. The springs
energize the vanes against the bore for better
sealing.
Detent Preload
Smalley Linear Springs are used to load pins
that are positioned inside grooves so a rotating
element can detent to specific positions. The
springs are designed to exert a precise load to
give the rotation a desired resistance.

Manufactured in USA Smalley 847.719.5900 41
SSRS Series - Circular-Grain® Shims
Smalley Shims are commonly used in conjunction with wave springs where a back-up plate is needed for housings made of softer metals
like aluminum or bronze, and for packings made of leather, neoprene or similar materials. Shims can function as spacers to change wave
spring operating heights. Adding or subtracting shims is an excellent method of adjusting load on a wave spring. Using a shim spacer can
also control tolerance buildups.
Stock Items in carbon steel and 17-7 PH stainless steel. However, Smalley can make them to order in nearly any size or material.
Smalley Part Outside Radial Part Smalley Part Outside Radial Part
Number 1, 3 Diameter Thickness Wall Weight 2 Number 1, 3 Diameter Thickness Wall Weight 2
SSRS-0075 .750 .024 .093 1.31 SSRS-0550 5.500 .030 .233 32.77
SSRS-0087 .875 .024 .093 1.55 SSRS-0562 5.625 .030 .233 33.54
+.000/-.015
SSRS-0100 1.000 .024 .103 1.97 SSRS-0575 5.750 .030 .233 34.32
SSRS-0112 1.125 .024 .138 2.91 SSRS-0587 5.875 .030 .233 35.10
SSRS-0125 1.250 .024 .138 3.28 SSRS-0600 6.000 .030 .233 35.88
+.000/-.045
SSRS-0137 1.375 .024 .138 3.65 SSRS-0612 6.125 .030 .233 36.66
SSRS-0150 1.500 .024 .150 4.33 SSRS-0625 6.250 .030 .233 37.43
SSRS-0162 1.625 .024 .150 4.73 SSRS-0637 6.375 .030 .233 38.21
+.000/-.020
SSRS-0175 1.750 .024 .150 5.13 SSRS-0650 6.500 .030 .233 38.99
SSRS-0187 1.875 .024 .150 5.53 SSRS-0675 6.750 .030 .233 40.54
SSRS-0200 2.000 .024 .150 5.93 SSRS-0700 7.000 .032 .375 70.76
SSRS-0212 2.125 .024 .150 6.33 SSRS-0725 7.250 .032 .375 73.43
SSRS-0225 2.250 .024 .150 6.73 SSRS-0750 7.500 .032 .375 76.10
SSRS-0237 2.375 .024 .178 8.35 SSRS-0775 7.750 .032 .375 78.77
+.000/-.060
SSRS-0250 2.500 .024 .178 8.83 SSRS-0800 8.000 .032 .375 81.44
+.000/-.025
SSRS-0262 2.625 .024 .178 9.30 SSRS-0825 8.250 .032 .375 84.11
SSRS-0275 2.750 .030 .188 12.86 SSRS-0850 8.500 .032 .375 86.78
Product Dimensions SSRS-0287 2.875 .030 .188 13.49 SSRS-0875 8.750 .032 .375 89.45
SSRS-0300 3.000 .030 .188 14.12 SSRS-0900 9.000 .032 .375 92.12
unless otherwise specified. SSRS-0312 3.125 .030 .188 14.74 SSRS-0950 9.500 .032 .375 97.46
+.000/-.090 +.000/-.080 +.000/-.070

SSRS-0325 3.250 .030 .233 18.77 SSRS-1000 10.000 .032 .375 102.80
OUTSIDE SSRS-0337 3.375 .030 .233 19.55 SSRS-1050 10.500 .032 .375 108.14
DIAMETER SSRS-0350 3.500 .030 .233 20.32 SSRS-1100 11.000 .032 .375 113.48
+.000/-.030
SSRS-0362 3.625 .030 .233 21.10 SSRS-1150 11.500 .032 .375 118.82
SSRS-0375 3.750 .030 .233 21.88 SSRS-1200 12.000 .032 .375 124.16
SSRS-0387 3.875 .030 .233 22.66 SSRS-1250 12.500 .032 .375 129.50
SSRS-0400 4.000 .030 .233 23.44 SSRS-1300 13.000 .032 .375 134.84
SSRS-0412 4.125 .030 .233 24.21 SSRS-1350 13.500 .032 .375 140.18
SSRS-0425 4.250 .030 .233 24.99 SSRS-1400 14.000 .032 .375 145.52
SSRS-0437 4.375 .030 .233 25.77 SSRS-1450 14.500 .032 .375 150.86
SSRS-0450 4.500 .030 .233 26.55 SSRS-1500 15.000 .032 .375 156.20
SSRS-0462 4.625 .030 .233 27.32 SSRS-1550 15.500 .032 .375 161.54
+.000/-.035
RADIAL SSRS-0475 4.750 .030 .233 28.10 SSRS-1600 16.000 .032 .375 166.88
WALL
SSRS-0487 4.875 .030 .233 28.88
SSRS-0500 5.000 .030 .233 29.66
SSRS-0512 5.125 .030 .233 30.43
SSRS-0525 5.250 .030 .233 31.21
THICKNESS
SSRS-0537 5.375 .030 .233 31.99
1
2
Lbs. per 1000.
3
Request FREE samples Get CAD downloads

Get free samples of any Simplify your design process
standard catalog item at by downloading CAD models
www.smalley.com/samples. of standard retaining rings
and wave springs at
Or use form on page 131 of www.smalley.com/cad-models.
this catalog. Requests typically
processed within 24 hours.

Spring & Fatigue Testers
Spring Tester
Springs are inspected for load, deflection, free height and
spring rate with this compression spring tester, designed
and built by Smalley. Main components of the tester are
described below.
The accuracy in checking spring load/deflection

characteristics is dependent on the accuracy and precision
of the testing device itself. The concept of accurate
compression testing relies greatly on the following
tester features:
1. Upper and lower plates must remain parallel throughout

the test. Generally, the distance between upper and
lower plates must be within .002 at any point, from zero
to full load.
2. Upper and lower plates must be rigid in that they should

not misalign with the spring positioned at any point on the
lower plate (note that placing a spring off-center induces
a moment, which tends to both tip the plates and cause Spring Tester
frictional drag.)
3. The load system must be free of friction, which can cause

hysteresis in the load values obtained in the test.
4. Testing surfaces of both the lower and upper plates

must be smooth and free of scratches, cracks or other
physical imperfections.
Fatigue Tester
Fatigue cycling is often a consideration when designing
compression springs. Testing provides a more accurate
prediction of actual cycle life and is recommended
whenever cycle life is critical or when calculations show
little margin over the cycle requirement.
Ideally, springs should be cycle tested in the actual

assembly. Where this is not feasible, Smalley offers testing
on high speed cycle machinery. The cycle test machinery
can be adjusted to various work heights and stroke lengths
to simulate the actual application.
Fatigue Tester

Wave Springs CC2015

Uploaded by

Copyright:

Available Formats

Wave Springs CC2015

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Wave Springs CC2015

Uploaded by

Copyright:

Available Formats

Wave Spring Introduction

All Springs Are Product Performance

SMALLEY WAVE SPRING COIL SPRING

10 smalley.com No-Tooling-Charges™ For Customs

Wave Spring Types

As a replacement for helical compression springs, Crest-to-Crest springs can develop

Manufactured in USA Smalley (847) 719-5900 11

Wave Spring Types (cont’d)

Request FREE samples Get CAD downloads

12 smalley.com No-Tooling-Charges™ For Customs

A. Pressure Relief Valve

Manufactured in USA Smalley (847) 719-5900 13

14 smalley.com No-Tooling-Charges™ For Customs

Manufactured in USA Smalley (847) 719-5900 15

Get CAD downloads

16 smalley.com No-Tooling-Charges™ For Customs

Manufactured in USA Smalley (847) 719-5900 17

Request FREE samples

18 smalley.com No-Tooling-Charges™ For Customs

Stock Items in carbon and 17-7 PH stainless steel.

Get CAD downloads

Manufactured in USA Smalley (847) 719-5900 19

20 smalley.com No-Tooling-Charges™ For Customs

BEARING O.D. LOAD AT

Manufactured in USA Smalley (847) 719-5900 21

What is Bearing Preload?

Stock Items in carbon steel and 17-7 PH stainless steel.

Bearing Part Numbers

22 smalley.com No-Tooling-Charges™ For Customs

Stock Items in carbon steel and 17-7 PH stainless steel.

Bearing Part Numbers

Manufactured in USA Smalley (847) 719-5900 23

Stock Items in carbon steel and 17-7 PH stainless steel.

Operates Clears Number Number

Material option: *Not available with shim ends

24 smalley.com No-Tooling-Charges™ For Customs

Stock Items in carbon steel and 17-7 PH stainless steel.

Operates Clears Number Number

Manufactured in USA Smalley (847) 719-5900 25

Stock Items in carbon steel and 17-7 PH stainless steel.

Operates Clears Number Number

Stock Items in carbon steel and 17-7 PH stainless steel.

Operates Clears Number Number

Manufactured in USA Smalley (847) 719-5900 27

Stock Items in carbon steel and 17-7 PH stainless steel.

Operates Clears Number Number

28 smalley.com No-Tooling-Charges™ For Customs

Stock Items in carbon steel and 17-7 PH stainless steel.

Operates Clears Number Number

Manufactured in USA Smalley (847) 719-5900 29

Stock Items in carbon steel and 17-7 PH stainless steel.

Operates Clears Number Number

30 smalley.com No-Tooling-Charges™ For Customs

Stock Items in carbon steel and 17-7 PH stainless steel.

Stock Items in carbon steel and 17-7 PH stainless steel.

Stock Items in carbon steel and 17-7 PH stainless steel.

Stock Items in carbon steel and 17-7 PH stainless steel.

Stock Items in carbon steel and 17-7 PH stainless steel.

Manufactured in USA Smalley (847) 719-5900 37

the expander flat inMULTI-WAVE