Hybrid Graphic Printer: UP-990AD UP-970AD

Download as pdf or txt
Download as pdf or txt
You are on page 1of 43

2-659-569-12 (1)

Hybrid Graphic
Printer
Instructions for Use _______________________________________ B

UP-990AD
UP-970AD
© 2006 Sony Corporation
Owner’s Record For the customers in Canada
The model and serial numbers are located at the rear.
This unit has been certified according to Standard CSA
Record these numbers in the space provided below.
Refer to these numbers whenever you call upon your C22.2 No.601.1.
Sony dealer regarding this product.
For the customers in the U.S.A. and
Model No. ____________________ Canada
Serial No. ____________________ Both the UP-990AD and the UP-970AD Hybrid
Graphic Printers are Non-Patient Equipment.
These units cannot be used in the vicinity of patients.
WARNING
To reduce the risk of fire or electric shock, do * Patient Vicinity
not expose this apparatus to rain or moisture.
m
83 t)
1.
To avoid electrical shock, do not open the R fee
cabinet. Refer servicing to qualified personnel (6
only.

THIS APPARATUS MUST BE EARTHED.

To disconnect the main power, unplug the AC


IN connector.
When you use this product connected to 240V single
phase, be sure to connect this product to a center tapped
This symbol indicates the equipotential circuit.
terminal which brings the various parts of a Important safeguards/notices for use in
system to the same potential.
the medical environments
1. All the equipments connected to this unit shall be
certified according to Standard IEC60601-1,
IEC60950-1, IEC60065 or other IEC/ISO Standards
For the customers in the U.S.A. applicable to the equipments.
2. When this unit is used together with other equipment
This equipment has been tested and found to comply in the patient area*, the equipment shall be either
with the limits for a Class A digital device, pursuant to powered by an isolation transformer or connected via
Part 15 of the FCC Rules. These limits are designed to an additional protective earth terminal to system
provide reasonable protection against harmful ground unless it is certified according to Standard
interference when the equipment is operated in a IEC60601-1.
commercial environment. This equipment generates, * Patient Area
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction
manual, may cause harmful interference to radio 5m
1.
R
communications. Operation of this equipment in a
residential area is likely to cause harmful interference in
which case the user will be required to correct the
interference at his own expense.

You are cautioned that any changes or modifications not


expressly approved in this manual could void your
authority to operate this equipment. 3. The leakage current could increase when connected
to other equipment.
All interface cables used to connect peripherals must be
shielded in order to comply with the limits for a digital
device pursuant to Subpart B of Part 15 of FCC Rules.

2
4. This equipment generates, uses, and can radiate radio
frequency energy. If it is not installed and used in
accordance with the instruction manual, it may cause
interference to other equipment. If this unit causes
interference (which can be determined by
unplugging the power cord from the unit), try these
measures: Relocate the unit with respect to the
susceptible equipment. Plug this unit and the
susceptible equipment into different branch circuit.
Consult your dealer. (According to standard
EN60601-1-2 and CISPR11, Class B, Group 1)

Caution
When you dispose of the unit or accessories, you must
obey the law in the relative area or country and the
regulation in the relative hospital.

Warning on power connection


Use a proper power cord for your local power supply.
1. Use the approved Power Cord (3-core mains lead) /
Appliance Connector / Plug with earthing-contacts
that conforms to the safety regulations of each
country if applicable.
2. Use the Power Cord (3-core mains lead) / Appliance
Connector /Plug conforming to the proper ratings
(Voltage, Ampere).
If you have questions on the use of the above Power
Cord/Appliance Connector/Plug, please consult a
qualified service personnel.

Warning on power connection for


medical use
Please use the following power supply cord.
With connectors (plug or female) and cord types other
than those indicated in this table, use the power supply
cord that is approved for use in your area.
United States Canada
Plug Type HOSPITAL GRADE* HOSPITAL GRADE*
Female end E62405, E35708 LR53182, LL022442,
LL088408
Cord type E159216, E35496 LL112007-1, LL20262,
Min.Type SJT LL32121, LL84494
Min.18 AWG Min.Type SJT
Min.18AWG
Minimum cord set 10A/125V 10A/125V
rating
Safety approval UL Listed CSA
*Note: Grounding reliability can only be achieved when the equipment
is connected to an equivalent receptacle marked ‘Hospital Only’ or
‘Hospital Grade’.

3
Others
Table of Contents Precautions ...........................................................35
On Safety ..........................................................35
On the Printer Carriage .....................................35
Getting Started On Installation ..................................................35
Overview ................................................................ 5 Maintenance .........................................................36
Location and Function of Parts and Controls .... 5 Cleaning the Cabinet ........................................36
UP-990AD ......................................................... 5 Cleaning the Thermal Head ..............................36
UP-970AD ......................................................... 7 Cleaning the Platen Roller ................................37
Paper ....................................................................... 9 Specifications ........................................................37
Paper You Can Use ............................................. 9 UP-990AD ........................................................37
Loading Paper in the Unit .................................... 9 UP-970AD ........................................................38
Troubleshooting ....................................................40
Error Messages ....................................................41
Analog Mode Index ......................................................................42
Connections .......................................................... 12
Adjustments and Settings Using the Menu ....... 13
Menu Flow ....................................................... 14
Menu List ......................................................... 16
Basic Menu Operations .................................... 19
Registering Menu Settings ............................... 21
Printing the Menu List ..................................... 21
Printing ................................................................. 22
Starting a Print Job ........................................... 22
Selecting the Printing Direction and Size ........ 24
Adjusting the Contrast and Brightness ............. 25

Digital Mode
Connections .......................................................... 26
Connecting to the USB Connector ................... 26
Installing the Printer Driver .............................. 26
Adjustments and Settings Using the Menu ....... 26
Menu Flow ....................................................... 27
Menu List ......................................................... 29
Basic Menu Operations .................................... 31
Registering Menu Settings ............................... 32
Printing the Menu List ..................................... 32
Printing ................................................................. 33
Starting a Print Job ........................................... 33
Adjusting the Contrast and Brightness ............. 34

4
Getting Started
Location and Function
of Parts and Controls
For more details, see the referenced page numbers
Overview

Getting Started
enclosed in parentheses ().

Stable, high-quality printing


• Capable of high-resolution images of 12.8 dots/mm. UP-990AD
• 8-bit processing provides monochrome printing with
up to 256 shades of gradation.
Front Panel
A variety of printing modes
Single-picture mode

Side mode

Reverse mode
A !Power ON/OFF Switch (page 9, 19, 22, 31, 33,
36)
Press to turn ON the printer. The LCD display
backlight as well as the CUT, FEED, COPY, and
Multi-picture mode PRINT buttons light.
* When set to digital mode, the PRINT button does not
light.

B Printer window display (LCD: liquid crystal


display) (page 14, 22, 27, 33)
A change of settings makes available an even greater The back light lights in green when the unit
number of print modes (see page 22). operates normally. Also, in normal operation, the
Storing print modes paper currently selected is indicated by the pointer
Store often used print modes as submenu values for on the LCD.
subsequent instant recall. For detailed information on the paper, see
“Installing the Printer Driver” on page 26 and
Supports both analog and digital input “Paper currently selected” on page 22 and 33.
• Prints NTSC and PAL color video signals as well as If an error occurs, a corresponding alarm message
EIA and CCIR monochrome video signals. is displayed.
• Compatible with Hi-Speed USB (USB 2.0 During menu operations, menu items and settings
compatible). are displayed.

Auto cut function (UP-990AD only) C Jog dial (page 20, 31, 36)
Automatically cuts the paper when printing completes. Used to make menu operations.

Printing to film (UP-990AD only) D CONTRAST (contrast) control (page 25)


The UP-990AD can print on transparent film using UPT- Adjusts the contrast of the printouts.
210BL (separately sold).
E BRIGHT (brightness) control (page 25)
Adjusts the brightness of the printouts.

Overview / Location and Function of Parts and Controls 5


F RECEIVING lamp Rear Panel
Lights when the printer receives print data from a
PC.

G CUT button (page 22, 33)


Press to cut the completed print using the internal
Getting Started

paper cutter.

H FEED button (page 10, 22, 33)


Hold down to feed paper. While a print job is in
progress, press to cancel the print job.

I CAPTURE button (page 23)


In the multi-picture mode, press to store the print
image in memory.
This function is not available in the single-picture
mode. A Equipotential terminal
Used to connect to the equipotential plug to bring
Note the various parts of a system to the same potential.
This function is available only in the analog mode. Refer to “Important safeguards/notices for use in
the medical environments” on page 2.
J COPY button (page 24)
In the multi-picture mode, use this button to print B t VIDEO IN (input) connector (BNC type)
images stored in memory (with the CAPTURE Connect to the video output connector of the video
button) side by side on a single sheet. equipment.
In the single-picture mode, press to print another
copy of the last printed image. C T VIDEO OUT (output) connector (BNC type)
In either mode, press once to print only the number Connect to the video input connector of the video
of prints set in the “QTY” menu. monitor. The output signal depends on the setting of
the “VIDEO” item of the menu.
K PRINT button
Prints the image currently displayed on the video D 75 Ω select switch
monitor. The image displayed when you press the ON: When nothing is connected to the VIDEO
PRINT button is stored in memory. OUT connector, set the switch to this position.
OFF: When a video monitor or other video
Note equipment is connected to the VIDEO OUT
connector, set the switch to this position.
This function is available only in the analog mode.
E ANALOG/DIGITAL switch
L OPEN/CLOSE button (page 10, 22, 33) Press to switch between analog and digital modes.
Press to open or close the paper door. While a print Turn the printer off before switching.
job is in progress, press to cancel the print job.
F REMOTE connector (page 12)
M Paper door Connects the RM-91 remote control unit for
Open to install and replace printing paper, and to controlling print operation from a distance.
clean the head and platen roller. Use the OPEN/
CLOSE button to open or close the paper door. G USB Cable Clamper
Holds and secures the USB cable connected to the
USB port.

H USB connector (4-pin connector)


Use the supplied USB cable to connect a PC with a
USB (USB 2.0 compliant) interface to this
connector.

6 Location and Function of Parts and Controls


I - AC IN connector
Use a proper power cord for your local power
UP-970AD
supply (not supplied).
Refer to “Warning on power connection” on page 3 Front Panel
and “Warning on power connection for medical
use” on page 3.

Getting Started
A !Power ON/OFF Switch (page 9, 19, 22, 31, 33,
36)
Press to turn ON the printer. The LCD display
backlight as well as the FEED, COPY, and PRINT
buttons light.
* When set to digital mode, the PRINT button does not
light.

B Printer window display (LCD: liquid crystal


display) (page 14, 22, 27, 33)
The back light lights in green when the unit
operates normally. Also, in normal operation, the
paper currently selected is indicated by the pointer
on the LCD.
For detailed information on the paper, see
“Installing the Printer Driver” on page 26 and
“Paper currently selected” on page 22 and 33.
If an error occurs, a corresponding alarm message
is displayed.
During menu operations, menu items and settings
are displayed.

C Jog dial (page 20, 31, 36)


Used to make menu operations.

D CONTRAST (contrast) control (page 25)


Adjusts the contrast of the printouts.

E BRIGHT (brightness) control (page 25)


Adjusts the brightness of the printouts.

F RECEIVING lamp
Lights when the printer receives print data from a
PC.

G FEED button (page 11, 22, 33)


Hold down to feed paper. While a print job is in
progress, press to cancel the print job.

Location and Function of Parts and Controls 7


H CAPTURE button (page 23) A Equipotential terminal
In the multi-picture mode, press to store the print Used to connect to the equipotential plug to bring
image in memory. the various parts of a system to the same potential.
This function is not available in the single-picture Refer to “Important safeguards/notices for use in
mode. the medical environments” on page 2.
Getting Started

Note B t VIDEO IN (input) connector (BNC type)


Connect to the video output connector of the video
This function is available only in the analog mode.
equipment.
I COPY button (page 24)
C T VIDEO OUT (output) connector (BNC type)
In the multi-picture mode, use this button to print
Connect to the video input connector of the video
images stored in memory (with the CAPTURE
monitor. The output signal depends on the setting of
button) side by side on a single sheet.
the “VIDEO” item of the menu.
In the single-picture mode, press to print another
copy of the last printed image.
D 75 Ω select switch
In either mode, press once to print only the number
ON: When nothing is connected to the VIDEO
of prints set in the “QTY” menu.
OUT connector, set the switch to this position.
OFF: When a video monitor or other video
J PRINT button
equipment is connected to the VIDEO OUT
Prints the image currently displayed on the video
connector, set the switch to this position.
monitor. The image displayed when you press the
PRINT button is stored in memory.
E ANALOG/DIGITAL switch
Press to switch between analog and digital modes.
Note
Turn the printer off before switching.
This function is available only in the analog mode.
F REMOTE connector (page 12)
K OPEN/CLOSE button (page 10, 22, 33) Connects the RM-91 remote control unit for
Press to open or close the paper door. While a print controlling print operation from a distance.
job is in progress, press to cancel the print job.
G USB Cable Clamper
L Paper Cutter Holds and secures the USB cable connected to the
Cut the paper as each image is printed. USB port.

M Paper door H USB connector (4-pin connector)


Open to install and replace printing paper, and to Use the supplied USB cable to connect a PC with a
clean the head and platen roller. Use the OPEN/ USB (USB 2.0 compliant) interface to this
CLOSE button to open or close the paper door. connector.

Rear Panel I - AC IN connector


Use a proper power cord for your local power
supply (not supplied).
Refer to “Warning on power connection” on page 3
and “Warning on power connection for medical
use” on page 3.

8 Location and Function of Parts and Controls


Paper Loading Paper in the
Use only Sony UPP-210SE/210HD/UPT-210BL paper Unit
designed for use with this unit. High print quality cannot
be guaranteed if any other paper is used with this unit,

Getting Started
Notes
and such paper could damage the unit.
• Do not touch the print surface of thermal printing
paper when loading paper. The fingerprints,
Paper You Can Use perspiration and creases that may result will lower the
print quality.
Print paper characteristics are as follows. • Use only UPP-210 series or UPT-210BL printing
paper (page 9).
Print Characteristics Paper Type
• Make the menu settings required by the loaded paper
TYPE I (Normal) UPP-210SE type (page 17, 30).
TYPE II (High Density) UPP-210HD
TYPE III (Thermal film) UPT-210BL 1 Press the power ON/OFF switch to turn on the
printer.
Note
The UP-970AD model cannot use UPT-210BL.

Notes on storing and handling paper


Storing unused paper
• Store unused paper at a temperature below 30°C
(86°F) in a dry location that is not exposed to direct
sunlight.
• Do not store unused paper near volatile liquids or
allow the paper to contact any organic volatile liquid,
cellophane tape, or any compound of vinyl chloride. The LCD display shows the message “SONY UP-
990AD” for the UP-990AD and “SONY UP-
Loading paper 970AD” for the UP-970AD.
• Handle the paper carefully when loading to avoid
touching the printing surface with your fingers. Notes
Perspiration or oil from you hands could cause
• The LCD display backlight lights in amber and
pictures to blur.
shows the message “EMPTY” when no printing
• After removing the label from the leading edge of the
paper is loaded.
paper, pull the paper out 15~20 cm (about 6~8 in.)
• The LCD display backlight lights in amber and
before printing. Label adhesive remaining on the
shows the message “DOOR” when the paper door
paper could spoil a picture.
is open.
Storing printouts • When set to analog mode, the LCD display shows
• To prevent printouts from fading or changing color, the message “NOINP” if there is no video signal
store them in a cool, dry location where the input.
temperature is not higher than 30°C (86°F).
• Store printouts in a polypropylene pouch or between
sheets of paper that contain no plastic.
• Do not store printouts where they will be exposed to
direct sunlight or high humidity.
• Do not store printouts near volatile liquids or allow the
prints to contact any organic volatile liquid,
cellophane tape, or any compound of vinyl chloride.
• To prevent fading, do not stack printouts on or under a
diazo copy sheet.
• To mount printouts on another sheet of paper, use
double-sides tape or a water base adhesive.
• Do not incinerate waste printer paper.

Paper / Loading Paper in the Unit 9


2 Press the OPEN/CLOSE button to open the paper 4 Insert the paper into the groove of the paper tray
door. and pull it out through the paper exit.

Note
Place the paper near the center of the groove of the
Getting Started

paper tray (inside of the guide). Note that paper


jams may occur if the paper is placed at the edge of
the groove of the paper tray.

3 Place the printing paper roll on the tray.


Using UPP-210SE/210HD

Remove label and pull


out 15 to 20 cm (about
6 to 8 inches).

Note
Pull out the printing paper to remove any slack and
possible creases.

Place the paper with the heat sensitive side facing


up. The printer will not print if the paper is
reversed.
5 Press the OPEN/CLOSE button to close the paper
door.
You can also push the paper door to close it.
Using UPT-210BL thermal film
* Cannot be used with the UP-970AD. Doing so may
cause a malfunction.
6 Remove paper leading edge.
UP-990AD
Correctly Inserted After loading paper, press the FEED button to feed
Remove label and pull out 15 to 20 cm (6 to 8 inches) of paper and press
out 15 to 20 cm (about the CUT button to remove it.
6 to 8 inches).
FEED Button

CUT Button

Incorrectly Inserted
15 to 20 cm

Place the paper with the heat sensitive side facing


up. The printer will not print if the paper is
reversed.

10 Loading Paper in the Unit


UP-970AD
After loading paper, press the FEED button to feed
out 15 to 20 cm (6 to 8 inches) of paper. Then use
the paper cutter to remove it. Be careful not to touch
the paper cutter when cutting the paper.

Getting Started
FEED Button

Note

To use UPT-210BL after printing with UPP-210SE/HD,


clean the head before printing as fine horizontal stripes
may otherwise appear on the paper.

Loading Paper in the Unit 11


Analog Mode

Connections Video equipment

Notes Color/black and


to video output white video monitor
• Turn off the power to each device before making any
connector
Analog Mode

connections.
• Connect the AC power cord last. Connecting cable
• After completing connections, switch to the analog (BNC y BNC)
(not supplied)
mode before turning on the printer.
• The printer will not print images imported via the USB Connecting cable
terminal. (not supplied) to video input
connector
to
VIDEO
IN

to VIDEO OUT

to REMOTE to -
AC IN

75 Ω select AC power
switch a) cord (not
supplied)

RM-91 remote control unit


(not supplied)

to wall outlet

a) Set the 75 Ω select switch as follows.


ON: When nothing is connected to the VIDEO OUT
connector, set the switch to this position.
OFF: When a video monitor or other video equipment is
connected to the VIDEO OUT connector, set the switch
to this position.

12 Connections
Adjustments and
Settings Using the Menu
You can carry out adjustments and settings to meet your
requirements. Those settings and adjustments are
retained even if the unit is turned off.
You can set up the unit according to its intended
purpose, connected equipments or your individual
preferences.

Analog Mode
You can store up to three settings as a set of user settings.

Adjustments and Settings Using the Menu 13


Menu Flow
The contents displayed on the LCD changes in sequence
as you turn the jog dial as shown in the following menu
flow chart, and you can make the settings for each menu
item.

UP-990AD Menu Flow


Analog Mode

(1): The single picture mode and multi-picture mode provide different functions. For details, see “Menu List”.
(2): The “SIZE.H”, “SIZE.V” settings and the signal system of the image to be captured determine the values you can set
with the Jog dial.
(3): The “SFT.H”, “SFT.V” settings and the signal system of the image to be captured determine the values you can set
with the Jog dial.
(4): The values you can set with the Jog dial in the analog mode are different from those in the digital mode.

14 Adjustments and Settings Using the Menu


UP-970AD Menu Flow

Analog Mode
(1): The single picture mode and multi-picture mode provide different functions. For details, see “Menu List”.
(2): The “SCAN” settings and the signal system of the image to be captured determine the values you can set with the
Jog dial.
(3): The values you can set with the Jog dial in the analog mode are different from those in the digital mode.

Adjustments and Settings Using the Menu 15


Menu List Item Function Settings
FEED To set the top and [FE: 0]to FE:15: Sets the
This section describes the menus displayed as you turn (UP-990AD) bottom margin of margin to one of 16 steps
the jog dial. The setting surrounded by a print. from 0 to 15. An increase of
indicates the factory setting. one step increases the top
and bottom margin by 5
Item Function Settings mm. The top and bottom
margin can be increased to
AGC To adjust the AG:ON: Adjusts the input 75 mm. The “0” setting is
input signal to the signal to the optimum level, the default value, which
optimum printing when the printout image still provides a narrow
level appears too dark or too margin between two
light.
Analog Mode

images.
[AG:OFF]: Normally select BACK: Cancels the setting
this setting. change and returns to the
BACK: Cancels the setting item selection column.
change and returns to the
item selection column. FEED To select the [FE: ON]: Increases the
(UP-970AD) paper feed margin between prints.
ASPCT a) To select the AS:1:1: Prints a video method used after FE:OFF: Sets when
aspect ratio signal with an aspect ratio printing. reducing the margin or
of 1:1. when printing multiple
[AS: 4:3]: Normally select images on the same sheet.
this setting. This reduces the margin
BACK: Cancels the setting between images allowing
change and returns to the you to print more images
item selection column per roll. However, with this
BEEP To turn operation BE: OFF: The operation setting, the FEED button
tones ON and tone does not sound. must be pressed before
OFF. Error tones [BE: ON]: The operation cutting the paper.
sound regardless sounds. BACK: Cancels the setting
of setting. BACK: Cancels the setting change and returns to the
change and returns to the item selection column.
item selection column. FRAME To select the FR:BLK: Sets the frame
CLEAN To start head [CLN: OK]: Starts the head color of the frame color to black.
cleaning cleaning. Be sure to use the between images [FR:WHT]: Sets the frame
supplied cleaning sheet. in multi-picture color to white.
BACK: Cancels the head mode. BACK: Cancels the setting
cleaning and returns to the change and returns to the
item selection column. item selection column.

CLEAR To delete images [CLR: OK]: Deletes all GAMMA To select the tone GA:3: TONE 3 Hard
stored in memory. images stored in memory. of the printouts gradation
BACK: Cancels CLEAR (density GA:2: TONE 2 Soft
and returns to the item gradation) [GA:1]: TONE 1 Standard
selection column. gradation
BACK: Cancels the setting
AT.CUT To turn on and off CT:OFF: Cuts the paper change and returns to the
(UP-990AD automatic cutting when the CUT button is item selection column.
only function) of completed pressed.
prints. [CT:ON]: Cuts the paper IMAGE To set the printout IM:NEG: Makes negative
automatically. to either positive printouts.
BACK: Cancels the setting printout or [IM:POS]: Makes normal
change and returns to the negative printout printouts.
item selection column. BACK: Cancels the setting
change and returns to the
DIR b) To select whether DI: REV: Starts to print in item selection column.
the top or bottom the reverse direction (from
of the screen is to the top of the screen). INFO To select whether IF:ON: Prints the
be printed first [DI: NOR]: Starts to print in or not the print information.
the normal direction (from conditions (such [IF:OFF]: Does not print the
the bottom of the screen). as contrast, information.
BACK: Cancels the setting bright, gammas BACK: Cancels the setting
change and returns to the and sharpness change and returns to the
item selection column. information) are item selection column.
printed under the
image

16 Adjustments and Settings Using the Menu


Item Function Settings Item Function Settings
INIT To return [INI:OK]: Returns all MEMRY To select the ME:FLD: When printing
(initialize) all settings to their factory memory mode fast-moving images (such
menu items to defaults. as a ball being thrown), the
their factory BACK: Cancels printout may be blue. If this
defaults. initialization and returns to happens, select this setting.
the item selection column. [ME:FRM]: Normally select
this setting.
INTRT To select In single picture mode
BACK: Cancels the setting
operation IN:ON: Stops printing
change and returns to the
performed when when the PRINT button is
item selection column.
printing of the pressed during printing and
current image is starts printing the image MENU To print the menu [ME:OK]: Prints the menu

Analog Mode
interrupted. captured at the instant you settings currently list currently set.
pressed the PRINT button. selected BACK: Cancels printing
[IN:OFF]: Printing does not and goes back to its item
stop even if the PRINT column.
button is pressed during
MIROR To print mirror MI:ON: Prints mirror
printing. When printing of
images. images.
the current image ends, the
[MI:OFF]: Prints normal
unit prints the image
images not mirror images.
captured at the instant you
BACK: Cancels the setting
pressed the PRINT button.
change and returns to the
In multi-picture mode
item selection column.
IN:ON: Stops printing
when the CAPTURE button MULTI To specify the MU:6: Prints six images on
is pressed during printing. number of images one sheet of the printout
The image captured at the to be printed on (six reduced images).
instant you pressed the one sheet of the MU:4: Prints four images
CAPTURE button is printout on one sheet of the printout
inserted at the location (four reduced images).
indicated by flashing. MU:2: Prints two images
[IN:OFF]: Disables the on one sheet of the printout
interruption of printing or (two reduced images).
image capture, even if the [MU:1]: Prints one full-size
CAPTURE button is image.
pressed during printing. BACK: Cancels the setting
BACK: Cancels the setting change and returns to the
change and returns to the item selection column.
item selection column.
PAGE Each time you [PG:1] to PG:6: Prints by
LOAD To load the LO:3: Loads the “SA:3” (These menu press the PRINT selecting the desired ONE
registered settings settings registered using the settings are button, the image image from among images
“SAVE” menu item. not available is stored in 1 to 6 and pressing the
LO:2: Loads the “SA:2” when “MU:2” memory. Up to 6 COPY button.
settings registered using the to “MU:6” is images can be BACK: Cancels the setting
“SAVE” menu item. selected in stored. change and returns to the
[LO:1]: Loads the “SA:1” “MULTI”.) You can select the item selection column.
settings registered using the desired image
“SAVE” menu item from 6 kinds of
BACK: Cancels the setting images stored in
change and returns to the memory and
item selection column. make a printout.
MEDIA To select the type ME:HG: Uses UPP-210SE. A.PRNT To turn on and off A.P:ON: Automatically
of paper [ME: HD]: Uses UPP- automatic prints when all the images
210HD. printing in multi- of the selected multi-picture
ME:BL: Uses UPT-210BL. picture mode. mode are captured without
However, the UP-970AD the need to press the COPY
model cannot use UPT- button.
210BL. [A.P:OFF]: Prints images
BACK: Cancels the setting when the COPY button is
change and returns to the pressed.
item selection column. BACK: Cancels the setting
change and returns to the
item selection column.

Adjustments and Settings Using the Menu 17


Item Function Settings Item Function Settings
QTY To set the print [QT:1] to QT:10: Prints SFT.V To specify the [V:0]: Adjusts the vertical
quantity from one to ten copies of (UP-970AD) position in the position. The numeric value
the same image. vertical direction displayed by turning the jog
BACK: Cancels the setting of the image to be dial depends on the signal
change and returns to the printed. system of the image to be
item selection column. captured and the range
setting of images captured
SAVE To register up to SA:3: Registers the menu
with “SCAN”.
three kinds of settings as No.3.
BACK: Cancels the setting
settings SA:2: Registers the menu
change and returns to the
settings as No.2.
item selection column.
[SA:1]: Registers the menu
Analog Mode

settings as No.1. SHARP To adjust the [SH:0] to SH:14:You can set


BACK: Cancels the setting sharpness of the the sharpness to any of 15
change and returns to the printout steps from 0 to 14. A higher
item selection column. number indicates greater
sharpness. A setting of “0”
SCAN To set the size of SC:WD2: Maximum size
indicates that the function is
(for the UP- the captured [SC:WD1]: Medium size
off, which is also the
970AD only) image. SC:NOR: Minimum size
default value.
BACK: Cancels the setting
BACK: Cancels the setting
change and returns to the
change and returns to the
item selection column.
item selection column.
SFT.H To specify the [S.H:192]: Moves the print
SIDE c) To select the S:SIDE: Prints the image
(UP-990AD) horizontal area horizontally relative to
direction in which rotated by 90 degrees
position of the the captured image. The
the image is to be counterclockwise.
image to be numeric value displayed by
printed [S:STD]: Prints the image in
printed. turning the jog dial depends
the same direction as that
on the “SIZE.H” setting
displayed on the monitor.
and the signal system.
BACK: Cancels the setting
BACK: Cancels the setting
change and returns to the
change and returns to the
item selection column.
item selection column.
SIZE.H To set the number [H: 1202]: NTSC signal
SFT.H To specify the [H:0]: Adjusts the
(for the UP- of dots in the input.
(UP-970AD) position in the horizontal position. The
990AD only) horizontal [H: 1202]: PAL signal input.
horizontal numeric value displayed by
direction of the Changing the value
direction of the turning the jog dial depends
printed image. increases or decreases the
image to be on the signal system of the
number of horizontal dots
printed. image to be captured and
to the right of the fixed left
the range setting of images
edge of the image.
captured with “SCAN”.
BACK: Cancels the setting
BACK: Cancels the setting
change and returns to the
change and returns to the
item selection column.
item selection column.
SIZE.V To set the number [V:480]: NTSC signal input.
SFT.V To specify the [S.V:20]: NTSC signal
(for the UP- of dots in the [V:574]: PAL signal input.
(UP-990AD) vertical position input.
990AD only) vertical direction Adjusts the vertical position
of the image to be [S.V:28]: PAL signal input.
of the printed of the bottom edge with
printed. Adjusts the vertical position
image. respect to the fixed top edge
of the printing area relative
of the image.
to the captured image. The
BACK: Cancels the setting
numeric value displayed by
change and returns to the
turning the jog dial depends
item selection column.
on the “SIZE.V” setting
and the signal system. TRAP To select the TR:ON: Prints the color
BACK: Cancels the setting input signal to be signal.
change and returns to the printed [TR:OFF]: Prints the black
item selection column. and white signal.
BACK: Cancels the setting
change and returns to the
item selection column.

18 Adjustments and Settings Using the Menu


Item Function Settings c) The print direction of the images printed is as follows.
VIDEO To select the VI:EE: Outputs the signal Image displayed on the monitor
video signal after it is processed by the
output from the printer.
VIDEO OUT [VI:THR]: Outputs the signal
connector on the directly without processing.
rear panel BACK: Cancels the setting
change and returns to the
item selection column.
BACK To exit menu Select this item and press
mode the jog dial to exit the menu
mode.

Analog Mode
a) The aspect ratio is as follows. Printouts

When S:STD is selected. When S:SIDE is selected

When AS:4:3 is selected

When AS:1:1 is selected

b) The printing direction is as follows.

Basic Menu Operations


This section describes the basic menu operation which
are common to each menu, taking “How to set the
printing direction” as an example.

1 Press the power ON/OFF switch to ON to turn the


unit on.
When DI:NOR is selected When DI: REV is selected The back light on the LCD lights in green.

LCD

Adjustments and Settings Using the Menu 19


2 Confirm that “READY” is displayed on the LCD, 5 Display “DI:REV” in the LCD by turning the jog
and press the jog dial. dial up or down, and then press the jog dial.
Analog Mode

The unit enters the menu mode.


When you perform a menu operation for the first
time after you purchase the unit, the top item of the
“AGC” menu is displayed.
If you have performed a menu operation already,
the item that you set last is displayed.

3 Display “DIR” by turning the jog dial up or down.

“DI:REV” is registered as the printing direction.


“DIR” reappears on the LCD.

Note
If about 20 seconds elapse without making any
menu operation after you have displayed the menu
item or setting, the display returns to “READY” on
the LCD and the unit exits the menu mode. In such
a case, the setting of “DIR” is not changed.

To cancel the setting


4 Press the jog dial.
1 Display “BACK” by turning the jog dial in step 5.

2 Press the jog dial.


The display on the LCD returns to “DIR.”

To continue menu operations


Make settings by repeating steps 3 to 5.

To end the menu operation

1 Display “BACK” by turning the jog dial after


The unit enters the mode in which you can select performing the operation of step 5.
the printing direction.
“DI:NOR,” which is the factory setting, is 2 Press the jog dial.
displayed on the LCD. “DI:NOR” is the currently The unit exits the menu mode.
selected setting.
In this menu operation, you will change the setting Menu lock function
to “DI:REV.” If the message “LOCK” is displayed and you hear the
alarm sound when you press the jog dial, the jog dial is
disabled because the menu operation function is locked.
If you want to perform a menu operation, contact the
nearest authorized dealer.

20 Adjustments and Settings Using the Menu


Registering Menu Settings 1 Load the settings of “LO:1” following the
procedure for loading the desired settings.
You can store up to three sets of settings made using the
menu, and you can load the desired setting when needed. 2 Change the loaded settings as required.
The unit retains these settings even if you turn off the
power. 3 Select “SA:2” following procedure for registering
the settings.
Note
When you use the unit for the first time after you
4 Press the jog dial.
The settings, changed in step 2, are registered as
purchase it, factory settings are registered in all three of
“SA:2” (No.2).
the stored selections.

Analog Mode
Registering new settings Printing the Menu List
1 Make all of the required settings. You can make a printout of the current menu settings.

2 Display “SAVE” by turning the jog dial, and then 1 Press the jog dial.
press the jog dial. The menu item you changed last is displayed.

3 Display the desired number by turning the jog dial, 2 Display “MENU” by turning the jog dial, and then
and then press the jog dial, again. press the jog dial.
The settings made in step 1 are registered in the
number selected in step 3. 3 Display “ME:OK” by turning the jog dial and then
press the jog dial.
The unit starts printing the current menu settings.
Loading the desired settings MENU is displayed on the LCD.
You can load the desired settings and make printouts
with the loaded settings. 4 Display “BACK” by turning the jog dial, and then
press the jog dial.
1 Confirm that “READY” is displayed on the LCD, The unit returns to the normal printing mode.
and press the jog dial.

2 Display “LOAD” by turning the jog dial, and then


press the jog dial again.

3 Display the number corresponding to the desired


settings, and then press the jog dial.
Settings corresponding to the number selected in
step 3 are loaded.

When you change the loaded settings


The unit operates according to the changed settings. In
this case, the unit operates according to these settings
until you load another set of settings, even if you turn off
the unit. When you load another group of settings, the
settings loaded previously are cleared.

To retain previously loaded settings


Example: Settings registered as “SA:1” are loaded and
settings are to be changed. To retain the original settings
of “SA:1” and to register the new settings as “SA:2,”
proceed as follows.

Adjustments and Settings Using the Menu 21


When the unit stops printing during printing
Printing When printing almost black images continuously, the
thermal head protection circuit may shut down the unit
Before Starting a Print Job to prevent the thermal head from overheating. In such a
Always check the following points: case, the message “COOL” is displayed on the LCD.
• Unit connected correctly? (page 12) Leave the unit until the head cools down and this
• Paper loaded correctly? (page 9) message disappears.
• Menu settings and menu adjustments done correctly?
To cancel a print job in progress
(page 13)
To cancel a print job in progress, press the OPEN/
• Video source being input?
CLOSE button, FEED button or CUT button.
Analog Mode

To feed paper
Starting a Print Job To feed paper, press the FEED button. The unit will
You can set up the printing direction, image size, all continue to feed paper as long as you hold down the
sorts of settings for printing, using the menu. This FEED button. Do not attempt to pull paper out of the
section describes operations after completing all sorts of unit with your hand.
settings using the menu.
Paper currently selected
1 Press the power ON/OFF switch to turn the unit on. You can confirm the paper currently selected on the
The back light on the LCD lights in green, and LCD. The pointer points to the paper currently selected.
“READY” is displayed on the LCD. In the following figure, the currently selected paper is
the UPP-210SE paper.
LCD UP-990AD

Indicates the UPP-210SE

Indicates the UPP-210HD

Indicates the UPT-210BL

2 Start the video source.


This operation is done using the controls of the
video equipment which you are using as a source.

3 Press the PRINT button when the image you want Note
to print is on the video monitor.
If “CT:ON” is selected in the “AT.CUT” menu,
The image displayed at the instant you press the
quickly remove the prints that have been cut.
PRINT button is captured into memory and is
Otherwise, the cut prints may block the paper exit
printed out immediately. Up to 6 captured images
and cause a paper jam to occur.
are stored in memory. When captured image
exceeds 6, the oldest data is overwritten with the UP-970AD
latest one in sequence.

When the message is displayed on the LCD Indicates the UPP-210SE


If a problem occurs, the back light on the LCD lights in
umber and the error message stating the problem is
Indicates the UPP-210HD
displayed on the LCD.

Message Cause and remedy


EMPTY Paper is not loaded. Load paper.
DOOR The paper door is open. Close the
paper door.
NOINP There is no video signal input. Input a
video signal.

22 Printing
If the printout image is blurred 4 Press the CAPTURE button again to capture any
A rapidly moving image may be blurred when printed. displayed image.
Should this occur, make a printout with “ME:FLD” When the “A.PRINT” menu is ON, printing starts
selected in the “MEMRY” menu item. automatically as soon as the number of images
specified by “MU:(2/4/6)” is captured. When the
Printing images stored in memory menu is OFF, press the COPY button to start
printing.
Each time you press the PRINT button, the image is
stored in memory. After 6 images have been stored, the Capturing two images (“MU:2 selected in
oldest image data is overwritten with the newest “MULTI”)
captured image in sequence. There are always 6 images
stored in memory. You can load the desired one from

Analog Mode
Image captured Image captured
among them and print it using the menu. in step 3 in step 4

1 Select “PAGE” from among the menu items. Printing direction


For detailed information on menu operation, see
“Basic Menu Operations” on page 19.
Capturing four images (“MU:4 selected in
2 Press the jog dial. “MULTI”)
“PG:1” is displayed on the LCD, and the image
printed last is displayed on the monitor.

3 Display the image that you want to print by turning


the jog dial up or down.

4 Press the jog dial. Capturing six images (“MU:6 selected in


The image selected in step 3 is loaded. “MULTI”)

5 Press the COPY button.


The image selected in step 3 is printed.

Printing two, four or six images on one


sheet
Use “MULTI” item of the menu to capture and print two “IF:ON” selected in “INFO” menu
to six different images on one sheet. In multi-picture mode, if “IF:ON” is selected in the
“INFO” menu, information about the last captured
1 Set “MULTI” item of the menu to “MU:2” - image is printed in the margin.
“MU:6”, according to the number of images you Example: If “MULTI” is set to “MU:6” and six images
want to print on one sheet. are captured, “IMAGE:6” is printed in the margin as the
information for that image.
2 Turn the Jog dial to display the BACK menu and
press the Jog dial.
The LCD display switches to the multi-picture
mode.
When “MU:2” is selected:
: 1 indicates that “1” flashes.
IMAGE:6
3 Press the CAPTURE button in step 3 of “Starting a [Image
Information]
Print Job” in the section “Analog mode” (page 22).
This captures the displayed image assigning it the
flashing number.
The next available number flashes in the LCD
display.
When “MU:2” is selected:
: The captured image is assigned “1” and
“2” starts flashing.

Printing 23
Making Copies of the Last Printout Selecting the Printing Direction and
Press the COPY button. The unit makes a copy of the
last printout. Each press of the COPY button prints the Size
number of images set in the “QTY” menu. Use the following menu items to select printing
direction and size.
Note • SIDE: Selects the printing direction of the image.
If you press the COPY button immediately after turning • SFT.H, SFT.V: Selects the horizontal or vertical
the power on, the alarm buzzer will sound as nothing is printing position.
stored in memory. • SIZE.H, SIZE.V (for the UP-990AD only):
Configures the width or height of the captured image.
To make multiple copies of the same printout • SCAN (for the UP-970AD only): Selects one of three
Analog Mode

Press the COPY button as many times as necessary available size settings for the captured image.
while copying the first printout. With each press of the
COPY button, a buzzer sounds and the number of Selecting the printing direction
images set in the “QTY” menu is printed. You can select the printing direction using the “SIDE”
menu item.
To interrupt copying
To cancel a print job in progress, press the OPEN/ To print in the same direction as the one
CLOSE button, FEED button or CUT button. displayed on the video monitor
Select “S:STD” from “SIDE.”
To make copies in different directions
You can copy the image stored last in a different To print the image rotated by 90 degree
direction. Before pressing the COPY button, select the counterclockwise
printing direction. Select “S:SIDE” from “SIDE.”

To print from a remote location Image displayed on the video monitor

If a Remote Control Unit RM-91 is connected to the


REMOTE connector on the rear panel, you can make
printing start at a short distance from the unit by pressing
the remote switch.

Single-picture mode
When an image you want to print appears, press the
remote switch.
Printouts
A screenshot of that instant is printed and saved in
memory. Up to six screenshots can be saved. Any new When “S:STD” is selected When “S:SIDE” is selected
screenshots beyond six will overwrite one of the
originally captured images.

Multi-picture mode
When an image you want to capture appears, press the
remote switch to save a screenshot of that instant in
memory.
Printing starts automatically when the number of images
set in the “MULTI” menu have been captured.

Note Determining image size


Even if “IN:ON” is selected in the “INTRT” menu,
pressing the remote switch performs the same action as (Model UP-990AD)
pressing the PRINT button or CAPTURE button in each Change the value for the “SIZE.H” menu item to
mode. configure the width settings of the captured image, and
change the value for the “SIZE.V” menu item to
configure the height settings.

(Model UP-970AD)
Use the “SCAN” menu item to select one of three size
settings for the captured image.

24 Printing
To set the range of the image to be Adjusting the Contrast and
printed
Brightness
(Model UP-990AD) You can adjust the contrast and brightness of the unit
Use “SFT.H” and “SFT.V” menu item to set the vertical using the CONTRAST control and BRIGHT control on
and horizontal range of the image to be printed. the front panel.
A change in “SIZE.H” and “SIZE.V” values changes the
upper limit of the “SFT.H” and “SFT.V” range.
The approximate position of the printing range is shown
on the monitor.

Analog Mode
SFT.H SIZE.H

SFT.V

SIZE.V

To adjust the contrast


You can adjust the contrast of printouts using the
CONTRAST control.
Captured image Printing range To make the contrast stronger: Turn the CONTRAST
control clockwise.
(Model UP-970AD)
To make the contrast weaker: Turn the CONTRAST
You can set the printing range vertically and horizontally
control counterclockwise.
using “SFT:V” and “SFT.H” menu items.
Also, “0” is the default position when setting the shift To adjust the brightness
with “SFT.H” and “SFT.V”. The value is negative when You can adjust the brightness of printouts using the
the default position is shifted to the left (i.e., when BRIGHT control.
“SFT.V” is increased). And the value is positive when To make the image brighter: Turn the BRIGHT
the default position is shifted to the right (i.e., when control clockwise.
“SFT.V” is decreased). To make the image darker: Turn the BRIGHT control
The approximate position of the printing range is shown counterclockwise.
on the monitor.
SFT.H Shift due to “SCAN” Note
setting value*
When the menu operation function is locked,
CONTRAST and BRIGHT controls are also disabled in
SFT.V
addition to the jog dial. If you want to use the
CONTRAST and BRIGHT controls, contact the nearest
authorized dealer.
Shift due
to “SCAN”
setting
value*

Captured image Printing range

* Depending on the “SCAN” value, there are three possible


printing ranges. For details, refer to “Menu List.”

Printing 25
Digital Mode Installing the Printer Driver
Install the printer driver provided with the printer. For
detailed instructions about how to install the unit driver,
refer to the Readme.txt file included on the supplied CD-
ROM disc.
Connections
After connecting the USB connecting cable (supplied)
to the unit and the computer, connect the power cord.
Adjustments and
For details about the unit connection, refer to the
manuals for the computer or other peripheral devices.
Settings Using the Menu
You can carry out adjustments and settings to meet your
Notes requirements. Those settings and adjustments are
• Before connecting the unit to the computer, turn off retained even if the unit is turned off.
the unit, computer, monitor, and all peripheral devices You can set up the unit according to its intended
Digital Mode

connected to the computer. purpose, connected equipments or your individual


• Before connecting the unit to the computer, disconnect preferences.
the power cord from the unit. Connect the power cord You can store up to three settings as a set of user settings.
to the unit only after connecting the unit and the
computer.
• Follow the connection procedures described in the
computer manual.
• Make sure that the cables are connected securely at
both ends.
• After completing connections, switch to the digital
mode before turning the power on.
• The printer will not print images imported via the
VIDEO IN connector.
• The unit drive software provided with the unit is not
suitable for using the unit connected to a network.
• Printer operation is not guaranteed when connecting
to the computer using the USB cable via a hub.
• Two or more units cannot be connected to a single
computer.

Connecting to the USB Connector

UP-990AD

to (USB)
connector

USB connecting
cable (supplied)

26 Connections / Adjustments and Settings Using the Menu


Menu Flow
The contents displayed on the LCD changes in sequence
as you turn the jog dial as shown in the following menu
flow chart, and you can make the settings for each menu
item.

UP-990AD Menu Flow

Digital Mode
(1): The values you can set with the Jog dial in the analog mode are different from those in the digital mode.

Adjustments and Settings Using the Menu 27


UP-970AD Menu Flow
Digital Mode

(1): The values you can set with the Jog dial in the analog mode are different from those in the digital mode.

28 Adjustments and Settings Using the Menu


Menu List Item Function Settings
FEED To select the [FE: ON]: Increases the
This section describes the menus displayed as you turn (UP-970AD) paper feed margin between prints.
the jog dial. The setting surrounded by method used after FE:OFF: Sets when
indicates the factory setting. printing. reducing the margin or
when printing multiple
Item Function Settings images on the same sheet.
This reduces the margin
BEEP To turn operation BE: OFF: The operation between images allowing
tones ON and tone does not sound. you to print more images
OFF. Error tones [BE: ON]: The operation per roll. However, with this
sound regardless sounds. setting, the FEED button
of setting. BACK: Cancels the setting must be pressed before
change and returns to the cutting the paper.
item selection column. BACK: Cancels the setting
CLEAN To start head [CLN: OK]: Starts the head change and returns to the
cleaning cleaning. Be sure to use the item selection column.
supplied cleaning sheet. GAMMA To select the tone GA:3: TONE 3 Hard

Digital Mode
BACK: Cancels the head of the printouts gradation
cleaning and returns to the (density GA:2: TONE 2 Soft
item selection column. gradation) [GA:1]: TONE 1 Standard
CLEAR To delete images [CLR: OK]: Deletes all gradation
stored in memory. images stored in memory. BACK: Cancels the setting
BACK: Cancels CLEAR change and returns to the
and returns to the item item selection column.
selection column. IMAGE To set the printout IM:NEG: Makes negative
AT.CUT To turn on and off CT:OFF: Cuts the paper to either positive printouts.
(UP-990AD automatic cutting when the CUT button is printout or [IM:POS]: Makes normal
only function) of completed pressed. negative printout printouts.
prints. [CT:ON]: Cuts the paper BACK: Cancels the setting
automatically. change and returns to the
BACK: Cancels the setting item selection column.
change and returns to the INFO To select whether IF:ON: Prints the
item selection column. or not the print information.
DIR a) To select whether DI: REV: Starts to print in conditions (such [IF:OFF]: Does not print the
the top or bottom the reverse direction (from as contrast, information.
of the screen is to the top of the screen). bright, gammas BACK: Cancels the setting
be printed first [DI: NOR]: Starts to print in and sharpness change and returns to the
the normal direction (from information) are item selection column.
the bottom of the screen). printed under the
BACK: Cancels the setting image
change and returns to the INIT To return [INI:OK]: Returns all
item selection column. (initialize) all settings to their factory
FEED To set the top and [FE: 0]to FE:15: Sets the menu items to defaults.
(UP-990AD) bottom margin of margin to one of 16 steps their factory BACK: Cancels
a print. from 0 to 15. An increase of defaults. initialization and returns to
one step increases the top the item selection column.
and bottom margin by 5 LOAD To load the LO:3: Loads the “SA:3”
mm. The top and bottom registered settings settings registered using the
margin can be increased to “SAVE” menu item.
75 mm. The “0” setting is LO:2: Loads the “SA:2”
the default value, which settings registered using the
still provides a narrow “SAVE” menu item.
margin between two [LO:1]: Loads the “SA:1”
images. settings registered using the
BACK: Cancels the setting “SAVE” menu item
change and returns to the BACK: Cancels the setting
item selection column. change and returns to the
item selection column.

Adjustments and Settings Using the Menu 29


Item Function Settings Item Function Settings
MEDIA To select the type ME:HG: Uses UPP-210SE. SIDE b) To select the S:SIDE: Prints the image
of paper [ME: HD]: Uses UPP- direction in which rotated by 90 degrees
210HD. the image is to be counterclockwise.
ME:BL: Uses UPT-210BL. printed [S:STD]: Prints the image in
However, the UP-970AD the same direction as that
model cannot use UPT- displayed on the monitor.
210BL. BACK: Cancels the setting
BACK: Cancels the setting change and returns to the
change and returns to the item selection column.
item selection column.
BACK To exit menu Select this item and press
MENU To print the menu [ME:OK]: Prints the menu mode the jog dial to exit the menu
settings currently list currently set. mode.
selected BACK: Cancels printing
and goes back to its item a) The printing direction is as follows.
column.
MIROR To print mirror MI:ON: Prints mirror
images. images.
Digital Mode

[MI:OFF]: Prints normal


images not mirror images.
BACK: Cancels the setting
change and returns to the
item selection column.
QTY To set the print [QT:1] to QT:255: Prints
quantity from 1 to 255 copies of the
same image. When DI:NOR is selected When DI: REV is selected
BACK: Cancels the setting
change and returns to the
item selection column.
RSIZE To adjust the size [RS:OFF]: prints the image
b) The print direction of the images printed is as follows.
of the image to as it appears on the display.
the size of the RS:ON: Magnifies the Image displayed on the monitor
printing paper. image to the size of the
printing paper.
BACK: Cancels the setting
change and returns to the
item selection column.
SAVE To register up to SA:3: Registers the menu
three kinds of settings as No.3.
settings SA:2: Registers the menu
settings as No.2.
[SA:1]: Registers the menu
settings as No.1. Printouts
BACK: Cancels the setting
change and returns to the
When S:STD is selected. When S:SIDE is selected
item selection column.
SHARP To adjust the [SH:0] to SH:14:You can set
sharpness of the the sharpness to any of 15
printout steps from 0 to 14. A higher
number indicates greater
sharpness. A setting of “0”
indicates that the function is
off, which is also the
default value.
BACK: Cancels the setting
change and returns to the
item selection column.

30 Adjustments and Settings Using the Menu


Basic Menu Operations 4 Press the jog dial.

This section describes the basic menu operation which


are common to each menu, taking “How to set the
printing direction” as an example.

1 Press the power ON/OFF switch to ON to turn the


unit on.
The back light on the LCD lights in green.

LCD
The unit enters the mode in which you can select
the printing direction.
“DI:NOR,” which is the factory setting, is
displayed on the LCD. “DI:NOR” is the currently
selected setting.

Digital Mode
In this menu operation, you will change the setting
to “DI:REV.”

5 Display “DI:REV” in the LCD by turning the jog


dial up or down, and then press the jog dial.
2 Confirm that “READY” is displayed on the LCD,
and press the jog dial.

The unit enters the menu mode.


When you perform a menu operation for the first
time after you purchase the unit, the top item of the
“BEEP” menu is displayed.
If you have performed a menu operation already,
the item that you set last is displayed.
“DI:REV” is registered as the printing direction.
3 Display “DIR” by turning the jog dial up or down. “DIR” reappears on the LCD.

Note
If about 20 seconds elapse without making any
menu operation after you have displayed the menu
item or setting, the display returns to “READY” on
the LCD and the unit exits the menu mode. In such
a case, the setting of “DIR” is not changed.

To cancel the setting

1 Display “BACK” by turning the jog dial in step 5.

2 Press the jog dial.


The display on the LCD returns to “DIR.”

Adjustments and Settings Using the Menu 31


To continue menu operations 3 Display the number corresponding to the desired
Make settings by repeating steps 3 to 5. settings, and then press the jog dial.
Settings corresponding to the number selected in
To end the menu operation step 3 are loaded.

1 Display “BACK” by turning the jog dial after When you change the loaded settings
performing the operation of step 5. The unit operates according to the changed settings. In
this case, the unit operates according to these settings
2 Press the jog dial. until you load another set of settings, even if you turn off
The unit exits the menu mode. the unit. When you load another group of settings, the
settings loaded previously are cleared.
Menu lock function
If the message “LOCK” is displayed and you hear the To retain previously loaded settings
alarm sound when you press the jog dial, the jog dial is Example: Settings registered as “SA:1” are loaded and
disabled because the menu operation function is locked. settings are to be changed. To retain the original settings
If you want to perform a menu operation, contact the of “SA:1” and to register the new settings as “SA:2,”
nearest authorized dealer. proceed as follows.
Digital Mode

1 Load the settings of “LO:1” following the


Registering Menu Settings procedure for loading the desired settings.
You can store up to three sets of settings made using the
menu, and you can load the desired setting when needed.
2 Change the loaded settings as required.
The unit retains these settings even if you turn off the
power.
3 Select “SA:2” following procedure for registering
the settings.
Note
4 Press the jog dial.
When you use the unit for the first time after you The settings, changed in step 2, are registered as
purchase it, factory settings are registered in all three of “SA:2” (No.2).
the stored selections.

Registering new settings Printing the Menu List


You can make a printout of the current menu settings.
1 Make all of the required settings.
1 Press the jog dial.
2 Display “SAVE” by turning the jog dial, and then The menu item you changed last is displayed.
press the jog dial.
2 Display “MENU” by turning the jog dial, and then
3 Display the desired number by turning the jog dial, press the jog dial.
and then press the jog dial, again.
The settings made in step 1 are registered in the 3 Display “ME:OK” by turning the jog dial and then
number selected in step 3. press the jog dial.
The unit starts printing the current menu settings.
Loading the desired settings MENU is displayed on the LCD.
You can load the desired settings and make printouts
with the loaded settings. 4 Display “BACK” by turning the jog dial, and then
press the jog dial.
1 Confirm that “READY” is displayed on the LCD, The unit returns to the normal printing mode.
and press the jog dial.

2 Display “LOAD” by turning the jog dial, and then


press the jog dial again.

32 Adjustments and Settings Using the Menu


To feed paper
Printing To feed paper, press the FEED button. The unit will
continue to feed paper as long as you hold down the
Before Starting a Print Job FEED button. Do not attempt to pull paper out of the
Always check the following points: unit with your hand.
• Unit connected correctly? (page 26)
Paper currently selected
• Paper loaded correctly? (page 9)
You can confirm the paper currently selected on the
• Menu settings and menu adjustments done correctly?
LCD. The pointer points to the paper currently selected.
(page 26)
In the following figure, the currently selected paper is
the UPP-210SE paper.
Starting a Print Job UP-990AD
You can set up the printing direction, image size, all
Indicates the UPP-210SE
sorts of settings for printing, using the menu. This
section describes operations after completing all sorts of Indicates the UPP-210HD
settings using the menu.

Digital Mode
Indicates the UPT-210BL

1 Press the power ON/OFF switch to turn the unit on.


The back light on the LCD lights in green, and
“READY” is displayed on the LCD.

LCD

Note
If “CT:ON” is selected in the “AT.CUT” menu,
quickly remove the prints that have been cut.
Otherwise, the cut prints may block the paper exit
and cause a paper jam to occur.

UP-970AD
2 Print the image using the application software.
Indicates the UPP-210SE
When the message is displayed on the LCD
If a problem occurs, the back light on the LCD lights in
umber and the error message stating the problem is Indicates the UPP-210HD
displayed on the LCD.

Message Cause and remedy


EMPTY Paper is not loaded. Load paper.
DOOR The paper door is open. Close the
paper door.

When the unit stops printing during printing


When printing almost black images continuously, the
thermal head protection circuit may shut down the unit Making Copies of the Last Printout
to prevent the thermal head from overheating. In such a
case, the message “COOL” is displayed on the LCD. Press the COPY button. The unit makes a copy of the
Leave the unit until the head cools down and this last printout. Each press of the COPY button prints the
message disappears. number of images set in the “QTY” menu.

To cancel a print job in progress Note


To cancel a print job in progress, press the OPEN/ If you press the COPY button immediately after turning
CLOSE button, FEED button or CUT button. the power on, the alarm buzzer will sound as nothing is
stored in memory.

Printing 33
To make multiple copies of the same printout
Press the COPY button as many times as necessary
Adjusting the Contrast and
while copying the first printout. With each press of the Brightness
COPY button, a buzzer sounds and the number of
You can adjust the contrast and brightness of the unit
images set in the “QTY” menu is printed.
using the CONTRAST control and BRIGHT control on
To interrupt copying the front panel.
To cancel a print job in progress, press the OPEN/
CLOSE button, FEED button or CUT button.

To make copies in different directions


You can copy the image stored last in a different
direction. Before pressing the COPY button, select the
printing direction.

Selecting the printing direction


Digital Mode

You can select the printing direction using the “SIDE”


menu item.

To print in the same direction as the one


displayed on the video monitor
Select “S:STD” from “SIDE.”

To print the image rotated by 90 degree


counterclockwise To adjust the contrast
Select “S:SIDE” from “SIDE.” You can adjust the contrast of printouts using the
CONTRAST control.
Image displayed on the video monitor To make the contrast stronger: Turn the CONTRAST
control clockwise.
To make the contrast weaker: Turn the CONTRAST
control counterclockwise.

To adjust the brightness


You can adjust the brightness of printouts using the
BRIGHT control.
To make the image brighter: Turn the BRIGHT
control clockwise.
Printouts To make the image darker: Turn the BRIGHT control
When “S:STD” is selected When “S:SIDE” is selected counterclockwise.

Note
When the menu operation function is locked,
CONTRAST and BRIGHT controls are also disabled in
addition to the jog dial. If you want to use the
CONTRAST and BRIGHT controls, contact the nearest
authorized dealer.

To print an enlarged copy of the captured


image
Set the “RSIZE” menu item to on to magnify the
captured image to the size of the selected printing paper
size.

34 Printing
Others

Precautions
On Safety
• Check the operating voltage before operation.
Ventilation holes (intake)
Operate the unit only with a power source specified in
Ventilation holes (exhaust)
“Specifications”.
• Stop operation immediately if any liquid or solid
object falls into the cabinet. Unplug the unit and have • If the unit is subjected to wide and sudden changes in
it checked by qualified personnel. temperature, such as when it is moved from a cold
• Unplug the unit from the wall outlet if you will not be room to a warm room or when it is left in a room with
using it for a long time. Disconnect the power cord by a heater that tends to produce large amounts of
grasping the plug. Never pull the cord itself. moisture, condensation may form inside the unit. In
• Do not disassemble the cabinet. Refer servicing to such cases the unit will probably not work properly,
qualified personnel only. and may even develop a fault if you persist in using it.

Others
• Connect the power plug of the unit to a wall outlet If moisture or condensation forms, turn off the power
with a protective earth terminal. The safety earth and allow the unit to stand for at least one hour.
should be properly established.

Caution on the paper cutter


A paper cutter is mounted with the UP-970AD. When
loading a paper or cleaning the UP-970AD, be careful
not to touch the paper cutter. Touching the paper cutter
may cause injury.

On the Printer Carriage


Do not carry or move the unit when the paper roll is
placed in the unit. Doing so may cause a malfunction.

On Installation
• Place the unit on a level and stable surface.
If you use the unit with placed on an uneven surface,
malfunction of the unit is likely to occur.
• Do not install the unit near heat sources. Avoid
locations near radiators or air ducts, or places subject
to direct sunlight or excessive dust, humidity,
mechanical shock or vibration.
• Provide adequate air circulation to prevent heat build-
up. Do not place the unit on surfaces such as rugs,
blankets, etc., or near materials such as curtains and
draperies.
• To prevent internal heat built-up, leave enough room
around the printer for air to circulate through the
ventilation holes (intake) on the left hand side and the
ventilation holes (exhaust) on the rear of the cabinet.

Precautions 35
3 Insert the supplied cleaning sheet, with the black
Maintenance surface facing down, into the groove of the paper
tray so that a small portion of the front edge of the
sheet sticks out of the paper exit.

Cleaning the Cabinet


Use a wrung out damp cloth, or a damp cloth soaked in
water and a mild detergent, to clean the cabinet surface. Insert the
cleaning sheet
To avoid damaging the cabinet of the unit, never use with the black
alcohol, thinner, or any other type of organic solvent, or surface facing
any type of abrasive cleaner, to clean the cabinet. down.

Cleaning the Thermal Head


If the printout is dirty or white stripes appear on the
printouts, clean the thermal head using the cleaning
sheet supplied.
Carry out the head cleaning operation using the menu.

Note
Others

A paper cutter is mounted with the UP-970AD. When


cleaning the thermal head, be careful not to touch the
paper cutter. Touching the paper cutter may cause injury.

1 Press the power ON/OFF switch to ON to turn the


unit on.
4 Press the OPEN/CLOSE button to close the paper
door.

5 Press the jog dial.


The menu item changed last is displayed.

6 Display “CLEAN” by turning the jog dial, and then


press the jog dial.

7 Confirm that “CLN:OK” is displayed, and then


press the jog dial.
The unit starts cleaning the thermal head.
“CLEAN” is displayed on the LCD.
2 Press the OPEN/CLOSE button to open the paper When the cleaning sheet stops and the alarm
door. sounds, the cleaning is completed.

8 Press the OPEN/CLOSE button to open the paper


door and remove the cleaning sheet.

9 Press the OPEN/CLOSE button to close the paper


door.

Note
Clean the thermal head only when necessary. If you
clean the thermal head too frequently, it may cause a
malfunction.

36 Maintenance
Cleaning the Platen Roller
If the paper cannot be ejected smoothly after printing,
Specifications
the platen roller may be dirty.
In such a case, clean the platen roller with a soft cloth
moistened with a damp clothe soaked in water and a
UP-990AD
mild detergent. Power requirement
100 to 240 V AC, 50/60 Hz
1 Press the power ON/OFF switch to ON to turn the Input current 2.4 A to 1.3 A max. at 25 °C
unit on. Operating temperature
5 °C to 35 °C (41 °F to 95 °F)
2 Press the OPEN/CLOSE button to open the paper Operating humidity
door. 20 % to 80 %
Operating pressure
3 Clean the platen roller gently with a damp clothe 700 hPa to 1,060 hPa
soaked in water and a mild detergent. Storage and transport temperature
–20 °C to +60 °C (–4 °F to +140 °F)
Storage and transport humidity
20 % to 80 %
Storage and transport pressure
700 hPa to 1,060 hPa
Dimensions 316 × 132.5 × 305 mm (w/h/d)

Others
(12 1/2 × 5/ 1/4 × 12 1/8 inches)
Mass 8 kg (17 lb 10 oz) (printer only)
Thermal head Thin-film thermal head, 2,560 dots
Gradation 256-level gradation (8-bit)
Resolution EIA: 1,280 × 508 dots
Platen roller CCIR: 1,280 × 612 dots
Picture size When “S:STD” is selected from
“SIDE”
Notes EIA: 188 × 143 mm
CCIR: 188 × 140 mm
• After the surface of the platen roller wiped has When “S:SIDE” is selected from
been dried completely, turn the platen roller to “SIDE”
clean another portion. EIA: 249 × 190 mm
• Turn the platen roller with hands. CCIR: 252 × 188 mm
• The UP-970AD is provided with a paper cutter. Printing speed About 8 sec./image
Take proper care to avoid cutting yourself. (at standard setting)
Picture memory Analog mode:
4 Press the OPEN/CLOSE button to close the paper 6 frames (800 k × 8 bits per frame)
door. Digital mode:
3,414 × 2,560 dots max.
Input connector VIDEO IN (BNC type)
EIA or CCIR composite video signals
1.0 Vp-p, 75 ohms/high-impedance
(EIA/CCIR automatically
discriminated)
Output connector
VIDEO OUT (BNC type)
EIA or CCIR composite video signals
1.0 Vp-p, 75 ohm loop-through/EE
switchable
REMOTE connector (stereo mini jack)

Maintenance / Specifications 37
1 GND
2 PRINT SIGNAL (TTL)
UP-970AD
Input of LOW pulse over 100 msec. Power requirement
initiates print. 100 to 240 V AC, 50/60 Hz
3 PRINT BUSY (TTL) Input current 2.4 A to 1.3 A max. at 25 °C
Goes HIGH during printing. Operating temperature
Addition of interface 5 °C to 35 °C (41 °F to 95 °F)
USB (USB 2.0 compatible) Operating humidity
Accessories provided 20 % to 80 %
Print media (1) Operating pressure
USB Cable 1-824-211-41 (SONY) (1) 700 hPa to 1,060 hPa
BNC Cable 1-551-475-32 (SONY) (1) Storage and transport temperature
Thermal head cleaning sheet (1) –20 °C to +60 °C (–4 °F to +140 °F)
Media label (1) Storage and transport humidity
CD-ROM (Operating Instructions, 20 % to 80 %
printer driver, printer driver install Storage and transport pressure
guide) (1) 700 hPa to 1,060 hPa
Software License Agreement (1) Dimensions 316 × 132.5 × 305 mm (w/h/d)
Getting Started (1) (12 1/2 × 5/ 1/4 × 12 1/8 inches)
Medical Specifications Mass 8 kg (17 lb 10 oz) (printer only)
Protection against electric shock: Thermal head Thin-film thermal head, 2,560 dots
Class I Gradation 256-level gradation (8-bit)
Others

Protection against harmful ingress of Resolution EIA: 1,280 × 508 dots


water: CCIR: 1,280 × 612 dots
Ordinary Picture size When “S:STD” is selected from
Degree of safety in the presence of a “SIDE”
flammable anesthetic mixture with EIA: 190 × 147 mm
air or with oxygen or nitrous oxide: CCIR: 190 × 142 mm
Not suitable for use in the presence When “S:SIDE” is selected from
of a flammable anesthetic mixture “SIDE”
with air or with oxygen or nitrous EIA: 253 × 194 mm
oxide CCIR: 257 × 190 mm
Mode of operation: Printing speed About 8 sec./image
Continuous (at standard setting)
Picture memory Analog mode:
6 frames (800 k × 8 bits per frame)
Digital mode:
3,414 × 2,560 dots max.
Input connector VIDEO IN (BNC type)
EIA or CCIR composite video signals
1.0 Vp-p, 75 ohms/high-impedance
(EIA/CCIR automatically
discriminated)
Output connector
VIDEO OUT (BNC type)
EIA or CCIR composite video signals
1.0 Vp-p, 75 ohm loop-through/EE
switchable
REMOTE connector (stereo mini jack)

38 Specifications
1 GND
2 PRINT SIGNAL (TTL)
Input of LOW pulse over 100 msec.
initiates print.
3 PRINT BUSY (TTL)
Goes HIGH during printing
Addition of interface
USB (USB 2.0 compatible)
Accessories provided
Print media (1)
USB Cable 1-824-211-41 (SONY) (1)
BNC Cable 1-551-475-32 (SONY) (1)
Thermal head cleaning sheet (1)
Media label (1)
CD-ROM (Operating Instructions,
printer driver, printer driver install
guide) (1)
Software License Agreement (1)
Getting Started (1)
Medical Specifications
Protection against electric shock:
Class I

Others
Protection against harmful ingress of
water:
Ordinary
Degree of safety in the presence of a
flammable anesthetic mixture with
air or with oxygen or nitrous oxide:
Not suitable for use in the presence
of a flammable anesthetic mixture
with air or with oxygen or nitrous
oxide
Mode of operation:
Continuous
The design and these specifications are subject to
change without prior notification.

Specifications 39
Symptom Causes/remedies
Troubleshooting Printouts dirty. Thermal head dirty?
tUse the head cleaning sheet
Before you call for service, please check the problems provided with the unit to clean the
and solutions described below. If you cannot solve the thermal head. (page 36)
problem, contact the nearest authorized dealer. The unit stops printing When printing almost black images
while printing almost continuously, the thermal head
Symptom Causes/remedies black images and the protection circuit may shut down the
message “COOL” is unit to prevent the thermal head from
First few prints New paper roll just installed? displayed on the LCD. overheating.
spotted with small tIf a new roll of paper has just been tStop printing and allow the thermal
dots. loaded, paper dust may cause white head to cool.
spots in printed images. Press the
FEED button and hold it down to White lines or small Is “TR:ON” selected in the “TRAP”
feed about 15~20 cm (6~8 in.) and letters on the screen menu item for black and white input
then release. (page 10) are not printed clearly. signals?
tSelect “TR:OFF” in “TRAP” when
Pressing the PRINT • Paper does not feed. the input signal is a black and white
button or the COPY tPower switched on? signal. (page 18)
button does not print tUnit connected correctly?
the image. (page 12, 26) Small squares appear Is “TR:OFF” selected in the “TRAP”
tPaper roll loose? (page 9) over the whole screen. menu item for color input signals?
tIs an item other than “MU:1” tSelect “TR:ON” in “TRAP” when
selected in the “MULTI” menu? the input signal is a color signal.
(page 17) (page 18)
Others

tIs the ANALOG/DIGITAL The printout is too • Is the 75 Ω select switch set
switch position correct? dark or too light. correctly?
• Alarm sounds. • Is the “MEDIA” menu item set
tPaper loaded correctly? (page 9) correctly? (page 17, 30)
tHas the thermal head • Is the “GAMMA” menu item set
overheated? The thermal head correctly? (page 16, 29)
may overheat when the unit
prints dark image continuously. The printout seems Is “AS:1:1” selected in the “ASPCT”
Wait until the head cools down. stretched or enlarged. menu item?
tIs the video signal of the image tSelect “AS:4:3.” (page 16)
input? The printing paper Is the platen roller dirty?
tIs the “MEDIA” menu item set does not feed tClean the platen roller (page 37)
correctly? smoothly.
• Paper feeds but printing does not
start. Jog dial does not • Is printing in progress?
tPaper loaded with the wrong operate menu. tCancel printing, or wait until
side up? (page 9) printing finishes.
• If set to digital mode, has the
The PRINT and Is the ANALOG/DIGITAL switch set printing data been queued or paused
CAPTURE buttons do to the digital mode? on the computer end?
not light. tSwitch to the analog mode. tCancel the queued print job, or
Black borders or Adjust the print area in the menu wait until printing finishes.
missing portions items.
around the printout
Paper Jams • Jammed paper visible?
tPress the OPEN/CLOSE button
to open the paper door, remove
the printout or the paper roll,
and then gently pull the jammed
paper out of the unit.
• Condensation collected in unit?
tIf the unit has just been brought
into a warm room from a cold
location, condensation may have
formed inside the unit. Switch
the unit off and let it set for 1 - 2
hours (until it warms to room
temperature), then try printing
again.

40 Troubleshooting
Error Messages
Messages appear on the LCD under the following
conditions. Take the remedial actions shown next to the
messages to correct the problem.

Messages Description and remedy


DOOR The paper door is open.
tPress the OPEN/CLOSE button or
push the paper door to lock it.
EMPTY • There is no paper loaded.
• Paper has been used up.
tLoad some paper.
COOL The protection circuit that prevents the
thermal head from overheating has
been activated.
tWait for the message to disappear.
Printing will then resume
automatically.
LOCK The menu operation function is locked.
The jog dial, CONTRAST control and

Others
BRIGHT control are disabled.
tIf you want to perform menu
operations or use those controls,
contact the nearest authorized
dealer.
ERROR An internal problem has occurred.
tContact the nearest authorized
SONY dealer.
NOINP No video signal is input.
tInput a video signal.
ME:NG The “MEDIA” menu item settings are
not correct.
tCheck whether the “MEDIA”
settings suit loaded printing paper.
tThe UP-970AD cannot use UPT-
210BL. Use UPP-210SE or UPP-
210HD printing paper.

Error Messages 41
P
Index Paper
loading paper in the unit 9
notes on storing and handling 9
A paper you can use 9
Analog Mode 12 Precautions
on installation 35
C paper cutter 35
printer carriage 35
Connections 12, 26 safety 35
connecting to the Printer driver 26
USB connector 26 Printing
installing the printer driver 26 adjusting the brightness 25, 34
notes 12, 26 adjusting the contrast 25, 34
cancelling 22, 33
D confirming paper 22, 33
Digital Mode 26 determining image size 24
feeding paper 22, 33
making copies 24, 33
E printing an enlarged 34
Error messages 22, 33, 41 printing images stored in
memory 23
G printing multiple images 23
selecting the printing
Getting Started 5 direction 24, 34
setting the range of the image 25
Index

L staring a print job 22, 33


Location and function of parts and
controls S
front panel 5, 7 Specifications 37
rear panel 6, 8

T
M
Troubleshooting 40
Maintenance
cleaning sheet 36
cleaning the cabinet 36
cleaning the platen roller 37
cleaning the thermal head 36
Menu
basic operations 19, 31
list 16, 29
loading the menu settings 21, 32
menu flow 14, 27
printing the menu list 21, 32
storing the menu settings 21, 32

O
Overview 5

42 Index
Sony Corporation

You might also like