3438952/3

IM-P343-16
CH Issue 3

EP5 and ISP5 Series

Electropneumatic Positioners
Installation and Maintenance Instructions

1. Safety information

2. Introduction

3. Installation

4. Commissioning

5. Maintenance

6. Spare parts

7. Fault finding

IM-P343-16
Printed in the CH
UK Issue 3 1
© Copyright 2007
2 IM-P343-16 CH Issue 3
 1. Safety information
Safe operation of these products can only be guaranteed if they are properly
installed, commissioned, used and maintained by qualified personnel (see
Section 1.11) in compliance with the operating instructions. General installation and
safety instructions for pipeline and plant construction, as well as the proper use of
tools and safety equipment must also be complied with.

1.1 Intended use

Referring to the Installation and Maintenance Instructions, name-plate and
Technical Information Sheet, check that the product is suitable for the intended
use/application. The products comply with the requirements of the European
Pressure Equipment Directive 97/23/EC and fall within the category 'SEP'. It should
be noted that products within this category are required by the Directive not to carry
the mark.
i) The products have been specifically designed for use on compressed air, which
is in Group 2 of the above mentioned Pressure Equipment Directive. The
products’ use on other fluids may be possible but, if this is contemplated, Spirax
Sarco should be contacted to confirm the suitability of the product for the
application being considered.
ii) Check material suitability, pressure and temperature and their maximum and
minimum values. If the maximum operating limits of the product are lower than
those of the system in which it is being fitted, or if malfunction of the product
could result in a dangerous overpressure or overtemperature occurrence, ensure
a safety device is included in the system to prevent such over-limit situations.
iii) Determine the correct installation situation and direction of fluid flow.
iv) Spirax Sarco products are not intended to withstand external stresses that may
be induced by any system to which they are fitted. It is the responsibility of the
installer to consider these stresses and take adequate precautions to minimise
them.
v) Remove protection covers from all connections and protective film from all
name-plates, where appropriate, before installation on steam or other high
temperature applications.

1.2 Access
Ensure safe access and if necessary a safe working platform (suitably guarded)
before attempting to work on the product. Arrange suitable lifting gear if required.

1.3 Lighting
Ensure adequate lighting, particularly where detailed or intricate work is required.

1.4 Hazardous liquids or gases in the pipeline

Consider what is in the pipeline or what may have been in the pipeline at some
previous time. Consider: flammable materials, substances hazardous to health,
extremes of temperature.

1.5 Hazardous environment around the product

Consider: explosion risk areas, lack of oxygen (e.g. tanks, pits), dangerous gases,
extremes of temperature, hot surfaces, fire hazard (e.g. during welding), excessive
noise, moving machinery.

IM-P343-16 CH Issue 3 3
1.6 The system
Consider the effect on the complete system of the work proposed. Will any proposed
action (e.g. closing isolation valves, electrical isolation) put any other part of the
system or any personnel at risk?
Dangers might include isolation of vents or protective devices or the rendering
ineffective of controls or alarms. Ensure isolation valves are turned on and off in a
gradual way to avoid system shocks.

1.7 Pressure systems

Ensure that any pressure is isolated and safely vented to atmospheric pressure.
Consider double isolation (double block and bleed) and the locking or labelling of
closed valves. Do not assume that the system has depressurised even when the
pressure gauge indicates zero.

1.8 Temperature
Allow time for temperature to normalise after isolation to avoid danger of burns.

1.9 Tools and consumables

Before starting work ensure that you have suitable tools and/or consumables
available. Use only genuine Spirax Sarco replacement parts.

1.10 Protective clothing

Consider whether you and/or others in the vicinity require any protective clothing
to protect against the hazards of, for example, chemicals, high/low temperature,
radiation, noise, falling objects, and dangers to eyes and face.

1.11 Permits to work

All work must be carried out or be supervised by a suitably competent person.
Installation and operating personnel should be trained in the correct use of the
product according to the Installation and Maintenance Instructions.
Where a formal 'permit to work' system is in force it must be complied with. Where
there is no such system, it is recommended that a responsible person should know
what work is going on and, where necessary, arrange to have an assistant whose
primary responsibility is safety.
Post 'warning notices' if necessary.

1.12 Handling
Manual handling of large and/or heavy products may present a risk of injury. Lifting,
pushing, pulling, carrying or supporting a load by bodily force can cause injury
particularly to the back. You are advised to assess the risks taking into account the
task, the individual, the load and the working environment and use the appropriate
handling method depending on the circumstances of the work being done.

4 IM-P343-16 CH Issue 3
1.13 Residual hazards
In normal use the external surface of the product may be very hot. If used at the
maximum permitted operating conditions the surface temperature of some products
may reach temperatures of 90°C (194°F).
Many products are not self-draining. Take due care when dismantling or removing
the product from an installation (refer to 'Maintenance instructions').

1.14 Freezing
Provision must be made to protect products which are not self-draining against
frost damage in environments where they may be exposed to temperatures below
freezing point.

1.15 Disposal
Unless otherwise stated in the Installation and Maintenance Instructions, this
product is recyclable and no ecological hazard is anticipated with its disposal
providing due care is taken.

1.16 Returning products

Customers and stockists are reminded that under EC Health, Safet y and
Environment Law, when returning products to Spirax Sarco they must provide
information on any hazards and the precautions to be taken due to contamination
residues or mechanical damage which may present a healt h, safet y or
environmental risk. This information must be provided in writing including
Health and Safety data sheets relating to any substances identified as hazardous
or potentially hazardous.

IM-P343-16 CH Issue 3 5
 2. Introduction
2.1 Introduction
The EP5 is a 2 wire loop powered positioner requiring a 4-20 mA control signal, and is
designed for use with linear pneumatic valve actuators. The positioner compares the
electrical signal from a controller with the actual valve position and varies a pneumatic output
signal to the actuator accordingly. The desired valve position is therefore maintained for any
control signal and the effects of varying differential pressure, stem friction and hysterisis
are overcome. A mounting kit is supplied to suit all NAMUR standard columns or yokes.
Note: A 0-10 Vdc input signal and an intrinsically safe version ISP5 are also available.

2.2 Operating principle

The EP5 operates on a force balance principle by means of a nozzle/flapper mechanism and
a feedback spring (refer to Figure 1).
The electrical control signal (A) is converted into a proportional air pressure (I). This pressure
is applied to the flapper (5) via the receiver (1), causing a deflection of the flapper relative to
the nozzles U1/U2. From the air supply (S) a reduced bleed of air is fed to the amplifier relay
(2) and into one of the nozzles U1/U2. As the flapper moves the pressure drop through the
nozzle is sensed by the amplifier relay. The amplifier relay outputs a signal (O) to the actuator
which is proportional to the pressure drop through the nozzle.
As the actuator moves, connecting lever (8) causes a change in tension of the reaction
spring (6). This tension is applied to the flapper causing it to move to a new position at which
the forces applied by the spring and the applied pressure (I) balance.

1 = Receiver 0.2 to 1 bar (3 to 15 psi)

2 = Amplifier relay
3 = Adjustable orifice: sensitivity setting
4 = Damping: outlet air flow adjustment
5 = Flapper 11
7 8
6 = Reaction spring
5 6
7 = Zero screw
8 = Positioner lever U1 U2
9 = Lock-nut 10 9
10 = Slider 1
11 = Sector lever

A = Control signal
I = I / P converter output
S = Air supply
O = Positioner output
U1 = Increase action nozzle
U2 = Decrease action nozzle 3
4
O
S
2
I
+
- A

Fig. 1

Important: This instrument bleeds air in normal operation at a rate of approximately

0.7 N m³ / hour at a supply pressure of 6 bar.

6 IM-P343-16 CH Issue 3
 3. Installation
Note: Before starting any installation observe the 'Safety information' in Section 1.
This publication is provided as a guide and it is recommended that it is read thoroughly prior
to installation. Also refer to the separate Installation and Maintenance Instructions for the
control valve and actuator.

3.1 Location
The positioner should be mounted in sufficient space to allow removal of the cover and provide
access to connections. When fitting to an actuator, ensure the positioner will not be exposed
to an ambient temperature outside the range -15°C to +65°C. The positioner enclosure is rated
to IP54 see BS EN 60534-6-1 1998.
Connection of air supply pressure (1.4 to 6 bar g) and control signal (4-20 mA or 0-10 Vdc)
should be considered prior to choice of location.

3.2 Mounting the positioner onto the actuator

The EP5 positioner may have been supplied already factory fitted onto the valve actuator.
However, using the mounting kit provided it can be attached retrospectively onto any other
type of valve and actuator conforming to NAMUR standards.

Step 1 Identify actuator type

For correct operation it is important to know two factors which will affect optimum movement
of the positioner feedback mechanism:

- The distance between the axes of the valve/actuator stem and the positioner slide pin.

- The travel of the valve actuator.

To ensure these are set correctly, please note the following:

- When attaching an EP5 to any Spirax Sarco valve actuator, ignore Step 3.

- For non-Spirax Sarco actuators, ignore Step 2.

IM-P343-16 CH Issue 3 7
Step 2 For attachment to Spirax Sarco actuators
Using the 2 off M6 pan head screws, securely attach the 'T' shaped sliding pin holder to
the valve actuator coupling block (Figure 2). Apply Loctite to the sliding pin and screw into
hole 'Y' (as shown) on the sliding pin holder and tighten.
Valve X Y
actuator
coupling
block

'T' shaped
sliding pin holder
Z

Fig. 2
Close-up of
sliding pin
holder fitted to
valve coupling.
Using the 2 off M8 x 15 hex head screws and 8 mm spring washers, attach the mounting plate
to the back of the positioner, utilising holes No. 2 in the bracket (Figure 3). Take care not to
over-tighten these screws and strip the threads.
Positioner 4 3 2 1

Mounting plate

Fig. 3

Step 3 For attachment to non-Spirax Sarco actuators

Using the 2 off M6 pan head screws, securely attach the 'T' shaped sliding pin holder to the
valve actuator coupling block (Figure 2). Depending on the travel of the valve actuator, apply
Loctite to sliding pin and screw into the correct hole on the sliding pin holder and tighten. Use
Figure 2 and Table 1 to determine the correct hole to use.

Table 1 Valve travel Hole to be used

8 - 15 mm X
15 - 30 mm Y
above 30 mm Z

Using the 2 off M8 x 15 hex head screws and 8 mm spring washers, attach the mounting
plate to the back of the positioner. The correct fixing hole may be determined by reference to
Figure 3, Table 2 and Figure 4. Take care not to over-tighten these screws and strip the threads.

8 IM-P343-16 CH Issue 3
 Actuator pillar Actuator
or yoke spindle

100%

50%

0%

D
➤
➤

Fig. 4 Pillar/yoke spacing, showing 50 % travel.

Table 2 D Hole to be used

Up to 125 mm 1
125 to 150 mm 2
150 to 175 mm 3
above 175 mm 4

Step 4 Temporarily apply adequate air pressure directly into the actuator so that the
valve is at 50% of travel (Figure 5).

Step 5 Engage the slide pin into the positioner lever (see Figure 5, noting the position of
the spring, above the pin) and loosely fix the positioner to the actuator. For yoke actuators
use the single elongated screw hole with the M8 x 20 screw and spring washer, for pillars
use the U-clamps.
Important: Slide positioner vertically up or down the yoke/pillars so the positioner lever is
horizontal at 50% travel, and the indicator at LHS is aligned (Figure 5). Secure the tightening
screws/nuts.

Slide pin Valve

position
indicator

Fig. 5

IM-P343-16 CH Issue 3 9
Step 6 Fit the angled protection plate to the rear of the positioner using the 2 off captive
M3 pan head screws. Access to these captive screws is from inside the positioner.

Step 7 Adjust the air supply pressure to stroke the actuator from 0% to 100% and ensure
the positioner lever rotates freely. Remove the temporary air supply from the actuator.

Step 8 Fitting a gauge block (optional)

To aid commissioning it is recommended to fit a gauge block and pressure gauges to all EP5s.
Please note that gauges and gauge block can be supplied as spare parts if required.
Fit gauges to the block before attaching the block to the EP5. Use thread sealant to ensure air
tight connections. The upper gauge displays the output of the I/P converter, and is normally
0 - 2 bar g. The lower gauge displays the positioner output pressure, so the gauge range
will depend on the actuator.
Remove any air fittings and blanking plug from the EP5, then attach the assembled block to
the EP5 using the 2 off socket head cap screws supplied. Ensure the sealing 'O' rings are
correctly fitted to seal the joints between the EP5 body and the gauge block. Replace the
fittings and blanking plug into the corresponding ports on the gauge block.

3.3 Connecting up

3.3.1 Pneumatic connections (with or without a gauge block)

Warning: Air supply must be dry, oil and dust free to ISO 8573-1: class 2:3:1. A coalescing
filter regulator such as a Spirax Sarco MPC2 will remove oil and dirt to meet this standard
if properly fitted and maintained. Dirty air supply may damage the product and invalidate
warranty. The supply air pressure must not exceed the maximum allowable air pressure
of the actuator.
Avoid use of ferrous pipe work after the MPC2. For best performance, set the air supply
pressure to about 0.5 bar g above the pressure required to fully travel the actuator.
Check all connections for leaks. Please note however that the EP5 bleeds air in normal
operation at a rate of approximately 0.7 N m³/hour at 6 bar supply pressure.
Pneumatic connections are located at the right hand end of the positioner and identified I,
S and O as follows:
I - Not used on EP5, fit ¼" NPT plug.
S - Air supply - 1.4 bar g to 6 bar g, depending upon required actuator spring range.
O - Output signal to the actuator.
Connections are ¼" NPT female. Interconnection between positioner and actuator should
be at least 6 mm OD tube.

10 IM-P343-16 CH Issue 3
3.3.2 Electrical connections
Cabling should be installed in accordance with BS 6739 - Instrumentation in Process Control
Systems: Installation design and practice or local equivalent.
The EP5 only requires a 4 - 20 mA (standard) or 2 - 10 Vdc (if requested) signal. Remove the
front cover and locate the terminal block and earth terminal post (Figure 6).
Note: Ensure resistance from earth post to local earth (e.g. pipework) is less than 1 .
Connection to the unit is through the Pg 13.5 cable gland (as supplied), which when used
with suitable cable will ensure the IP54 protection rating. Appropriate conduit connections
may be used instead.
Connect conductors (0.5 to 2 mm²) to the terminal block and earth post (3 mm²) noting the
polarity +/- shown in Figure 6.
In hazardous areas use model ISP5 with intrinsic protection (type EEx ia llC T6, T5,T4) ensuring
the power supply from adjoining equipment is certified in accordance with EN 50.014 and
EN 50.020 standards, in respect of the limits of electric features shown at approval stage.
Refer to approval certificate supplied with each ISP5 product.

Earth
terminal
Cable post
gland I
Terminal
block
-
+ S

Fig. 6

IM-P343-16 CH Issue 3 11
 4. Commissioning
Once the positioner has been mounted and connected up, proceeed as follows.

Step 1 Set the valve action

Establishing the correct action of the valve is done by:

a. Connection to either U1 or U2 nozzles (see Figure 7) and

b. Setting the slider in the upper or lower portion of the crescent shaped sector lever (Figure 8).

Connection
to nozzle U2
Connection
to nozzle U1

Fig. 7

U1 = Increase action = With increasing electrical control signal the air pressure to the
actuator will increase.

U2 = Decrease action = With increasing electrical control signal the air pressure to the
actuator will decrease.

To change the working nozzle connections (U1 or U2):

Disconnect the air supply. Loosen the retaining plate and rotate it clear of the tube holder.
Pull the tube holder clear of its seat and re-insert the tube holder into the alternative seat
location. Lock in place with alternative retaining plate (lock unused retaining plate to
prevent loss of plate). Reconnect air supply.

12 IM-P343-16 CH Issue 3
To change the slider location:
Refer to Figure 8 to determine the correct portion. To change the slider slacken the screw
and slide it into the correct portion of the arm.

Fig. 8a Increase action and spring extend

Upper
sector


I
* U1 nozzle
S
O

Fig. 8b Increase action and spring retract



* U1 nozzle

I
S
O
Lower
sector

Fig. 8c Decrease action and spring extend



* U2 nozzle

I
S
O Lower
sector

Fig. 8d Decrease action and spring retract

Upper
sector

I


S
O
* U2 nozzle

* The arrow shows the stem movement direction when the input control signal increases.

IM-P343-16 CH Issue 3 13
Step 2 Set sensitivity
The positioner sensitivity is adjusted using the sensitivity screw (Xp %, see Figure 10). It is
set depending on air supply pressure. Before the commissioning stage it is essential to set
the sensitivity within a proportional band of (3% to 6%). Use Figure 10 to adjust the sensitivity
screw by firstly fully closing the screw (clockwise), then reopen the screw:-

Supply pressure (S) 1.4 bar - Screw open ¾ of a turn

4.0 bar - Screw open ¼ of a turn
6.0 bar - Screw open of a turn

1.4 bar

Supply pressure
Opening degree

¾
½
¼ 4.0 bar
1
/8 6.0 bar

0 3 6 (Xp %)
➤
➤
Fig. 9 Xp correct value

To increase positioner sensitivity close the adjusting screw, to decrease sensitivity open the
screw. Do not open the screw beyond the mechanical lock.

Sensitivity screw

Fig. 10

Note: Adjustment of the Xp % screw causes a change of positioner 'zero' point, and it is
therefore important to repeat the zeroing and travel setting procedures (Steps 4 and 5) after
any changes.

14 IM-P343-16 CH Issue 3
Step 3 Set damping
The final adjustment of damping screw should be performed with plant in operation, in order
to limit, if necessary, the actuation speed. During the commissioning set the damp screw flush
with the body see Figure 11.

Damp screw

Fig. 11

The reduction of air flowrate capacity to the actuator will slow down the valve movement to limit
the effect of cycling hunting. Closing the screw (clockwise) increases damping, and vice versa.

Step 4 Set zero point

Check all air and electrical connections are in place. Check air supply pressure (S) is correct
(see Section 3.3.2). Check electrical control signal (A) (see Section 3.3.3) is at the minimum
required (normally 4 mA or 0 V), but the application may require a different setting. It may also
be advisable to increase the minimum by 0.5 mA or 0. 25 V to ensure the valve is completely
closed. For 3-port valves (or if the action has been reversed for 2-port valves) a higher electrical
signal corresponds to the closed valve position, it may be beneficial to decrease the maximum
electrical control signal to 19.5 mA or 9.75 V. This will ensure that the valve is firmly seated
when the full electrical signal of 20 mA or 10 V is applied.
Locate zero point adjustment screw (see Figure 12) and release the locking ring. Adjust screw
until the valve starts to move and lock the adjuster in place.
Check the zero point by reducing the electrical control signal (A) (see Section 3.3.3) to zero.
Slowly increase the electrical control signal towards the minimum level whilst monitoring valve
movement. Should movement take place before or after the minimum control signal then repeat
adjustment until movement coincides with minimum control signal.
Locking ring Slider

Zero point
adjustment screw
Central locking screw

Sector lever

Fig. 12

Note: Positioners fitted with a gauge block have the benefit of anticipating valve movement
by indicating increases of output air pressure.

IM-P343-16 CH Issue 3 15
Step 5 Set travel
Increase the electrical control signal to the upper value (normally 20 mA or 10 V, but this
depends on the application) and now check the travel of the valve. If required, slacken the
central locking screw (see Figure 12) and adjust the slider up or down the upper or lower portion
of the crescent shaped sector lever. Moving the slider away from the pivot will reduce the
travel, and vice versa. Normally, except with 3-port valves, the fully open position is achieved
before the valve plug hits the upper mechanical stop of the valve/actuator. Avoid settings of
the positioner that allow contact with this mechanical stop. Vary the electrical control signal
around the upper value to verify the travel setting, and if necessary repeat the adjustment of
the slider until the required travel occurs at the upper value.
Important: Zero and travel settings on EP5 are not independent of each other, so re-check
the zero setting as described in Step 4. It may prove necessary to repeat Steps 4 and 5
several times until acceptable zero and travel settings are achieved. For fine adjustment of
the travel, the potentiometer shown in Figure 13 can be used. This should only be used for
final adjustment of +/- 5%.
When complete, lock both zero and travel adjustments.

Travel adjustment
potentiometer

Fig. 13

Split range operation

EP5 may be split ranged to sequentially actuate two valves from one control signal
(For example: valve 1 set to 4 - 12 mA and valve 2 set to 12 - 20 mA). Split ranging is achieved
by adjustment of the zero and travel settings refer to Steps 4 and 5.

16 IM-P343-16 CH Issue 3
 5. Maintenance
5.1 Regular maintenance
1. Drain any build-up within the air supply filter set as impurities such as oil, water and dirt
will cause inconsistent operation.
2. Ensure air supply is at the correct pressure (see Section 3.3.2 and refer to actuator TI).
3. Make visual checks to ensure the valve is operating correctly.

5.2 Corrective maintenance

5.2.1 Removal and cleaning of sensitivity adjuster (see Figure 14):
- Loosen and remove lock.
- Note setting then remove sensitivity screw.
- Wash adjuster with solvent, checking condition of the cone and ensuring 0.35 mm side
hole is clear.
- Dry with clean compressed air to ensure no remaining contaminants.
- Refit the cleaned adjuster and unscrew it 1 turn from its stop.

Fig. 14

- Refit the lock to touch the adjuster top and secure with lock-nut.
- Set sensitivity see Step 2, Section 4, Commissioning.
- Reset zero and span if required.

IM-P343-16 CH Issue 3 17
5.2.2 Removal and cleaning of capillary orifice (see Figure 15):
- Loosen locking plate screw.
- Rotate locking plate to expose capillary orifice.
- Using supplied extractor/cleaner pull the orifice from the body.
- Clean the small orifice and cross drilling using only the special cleaning wire supplied.
- Reassemble the orifice ensuring both 'O' rings are in place and the lock plate covers the orifice.

Extractor/cleaner

Extracting Spare 'O' ring Cleaning wire

thread
Capillary orifice

Fig. 15

Damping faces

Locking plate
Capillary orifice

Fig. 16
Capillary extractor / cleaner

5.2.3 Check damping grease:

- Ensure gap of 1 mm exists between faces of damper. Adjust if necessary.
- Verify grease is present between faces.
- Replace grease if necessary (contact Spirax Sarco for details).

18 IM-P343-16 CH Issue 3
 6. Spare parts
Available spares
Gauge block (without gauges) 1
Gauge 0 - 2 bar 2
Gauge 0 - 4 bar 3
Gauge 0 - 7 bar 4
Springs and tubes 5
Set of gaskets, diaphragms and orifice 6
Amplifying relay set 7

How to order spares and accessories

Always order spares by using the description in the column headed 'Available spares' and a
description of the product, together with the TAG number.
Example: 1 off Gauge 0-2 bar for a Spirax Sarco EP5 positioner, TAG 907.

6 7 5 1

TAG number
3 or 4

Fig. 17

Product return procedure

Please provide the following information with any equipment being returned:-
1. Your name, Company name, address and telephone number, order number and invoice
and return delivery address.
2. Description of equipment being returned.
3. Description of the fault.
4. If the equipment is being returned under warranty, please indicate:
i. Date of purchase
ii. Original order number

Please return all items to:

Returns Investigations Department
Runnings Road,
Kingsditch Trading Estate
Cheltenham
Glos, GL51 9NX
United Kingdom

Alternatively, please return any items to your local Spirax Sarco branch.
Please ensure all items are suitably packed for transit (preferably in the original cartons).

IM-P343-16 CH Issue 3 19
 7. Fault finding
Output pressure too low or zero
Cause Remedy
a. No control signal a. Restore mA signal
b. Low air supply pressure b. Verify actuator air pressure requirement
c. Clogged or dirty sensitivity adjuster c. Clean adjuster see Section 5.2.1
d. Clogged or dirty capillary orifice d. Clean orifice see Section 5.2.2
e. Incorrect set-up e. Recalibrate see Section 4, Steps 1 to 5
f. Damaged pneumatic actuator or piping f. Verify replace as necessary
g. Port I not blanked or leaking g. Insert ¼" NPT blank in port I
Output pressure too high
Cause Remedy
a. Sensitivity adjuster open too far a. Recalibrate see Section 4, Step 2
Actuator movement too slow
Cause Remedy
a. Low air supply capacity a. Check supply capacity and pipe sizes
b. Damping screw closed too far or clogged b. Recalibrate see Section 4, Step 3
Actuator failing to close
Cause Remedy
a. Output pressure too low a. Refer to previous fault
b. Incorrect zero point b. Recalibrate see Section 4, Step 4
c. Damping screw closed or clogged c. Clean screw and recalibrate see Section 4, Step 3
d. Valve / actuator coupling incorrect d. Reset (refer to valve/actuator IMIs)
e. Actuator too small e. Fit correct actuator
Actuator failing to fully open valve
Cause Remedy
a. Output pressure too low a. Refer to previous fault
b. Incorrect travel adjustment b. Recalibrate see Section 4, Step 5
c. Damping screw closed or clogged c. Clean screw and recalibrate see Section 4, Step 3
d. Valve / actuator coupling incorrect d. Reset (refer to valve/ actuator IMIs)
e. Actuator too small e. Fit correct actuator
Hunting
Cause Remedy
a. Incorrect controller set up (P, I, and D) a. Verify and adjust according to process requirement
b. Sensitivity orifice closed too far b. Adjust by opening sensitivity screw
see Section 4, Step 2
c. Excessive valve friction c. Verify and maintain as valve IMI
d. Control valve over-sizing d. Verify operating conditions against valve capacity.
Note: The effects of hunting caused by valve over-sizing or unstable process conditions can be
reduced by adjustment of damping screw see Section 4, Step 3.

20 IM-P343-16 CH Issue 3