Multi - Choice Question Paper (MSR-WI-1)
Multi - Choice Question Paper (MSR-WI-1)
Multi - Choice Question Paper (MSR-WI-1)
_--
TWI
rllOI.--------________ THE WELDING INSTITUTE
4. Comp,ound welds:
a. .Always contain butt and fillet welds
b. Joints, which have combinations of welds made by different welding
processes.
Combinations between two different weld types
All of the above.
rllflL-----___________
T HE WELDING INSTITUTE
~
Measure residual stress.
Check calibration certificates. \
6. Under most conditions, which of the following welding positions will deposit the
most weld metal.
a. PG.
b. PE.
c. PC.
G
PA.
11. Which of the following welding processes/technique is likely to be used for the
b.
MMA, PG position.
Mechanised MAG.
c. Submerged arc.
d. All of the above.
--vX None of the above.
12. When measuring the welding parameters with the MMA welding process for
the purpose of approving a welding procedure, the Welding Inspector should
measure the voltage:
c.
d.
Anywhere along the welding cable.
Always from the voltmeter on the welding plant.
As near to the welding terminals as possible.
l
13. In the MMA welding process, which of the following is most likely to be caused
by a welder with a poor technique?
unknown.
16. When carrying out visual inspection, the specification makes no mention of the
requirements for visual inspection, in this situation what should you do?
Carry out normal visual inspection. ,
Seek advice from higher authority.
17. Under most circumstances, which of the following do you consider to be duties
of a welding inspector?
a. The supervision of welders.
b. Procedure writing. 1
~
Qualifying welders I
19. In an arc welding process, which of the following is the correct term used for
a. Filling rate.
c:!
d.
Deposition rate.
Weld deposition.
Weld duty cycle.
20. What is the term given for the area of a welded joint just outside the weld
b.
Heat affected zone.
The weld zone.
c. Fusion zone.
d. All of the above terms may be used.
25. On a single-V butt weld, the distance through the centre of the weld from root
to face is called:
a. Reinforcement.
b. Penetration.
~
13.5 mm.
12.5 mm.
27. The need for pre-heat for steel will increase if:
15 f'I . tO~1
a.
®c.
d.
The material thickness reduces.
@ Bothe a and b
32. When open site working, serious porosity in metal arc welds is brought to your
attention. What would you investigate? ...._
a. Electrode type
G d.
Electrode storage
Day temperature
Power plant type .
e. All of the above.
33. What is the maximum allowable HIILO for 8mm material if the code states the
following. "Linear misalignment is permissible if the maximum dimension does
not exceed 10% of t up to a maximum of 2mm"
~ ~~~m )
c. 8mm
d. None of the above, insufficient information provided
34.
"Veed" cap ripple on the cap. This may indicate which of the following
a. Incorrect electrode
X Excessive travel speed·
36. When visually inspecting a fillet welded Tee piece, which of the following is
normally measured to determine the fillet welds size.
X Leg length
b. Throat thickness
o
c.
e.
Design throat thickness
Both a and b.
All of the above ..
39. Arc strikes associated with a welded joint may be considered a serious defect.
Because
a. The presence of arc strikes may lead to hardening of the parent
material
b. The presence of arc strikes may lead to cracking
c. The arc strike may cause a reduction in parent material thickness.
d. Both a and b.
40 Which of the following defects would usually be considered the most serious.
a. Lack of interun fusion.
b.
CVd.
e.
Slag inclusions.
Porosity
All of the above.
I
WIS 5 QupaperMSR-WI-1 8 of 8
issue 5 Date: 17/01/10