Scribd
Upload
215 views5 pages

Lec 13

The document provides information about fluidized catalytic cracking (FCC) units used in petroleum refineries. It discusses the key components and reactions that occur in FCC units. FCC units upgrade heavy petroleum streams like vacuum gas oil into more valuable products like gasoline and light olefins. The process involves circulating a zeolite catalyst between a riser reactor, where cracking reactions take place, and a regenerator, where coke is burned off the catalyst to regenerate it. Typical feedstocks and products of FCC units are also described.

Uploaded by

Ghazy alshyal
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
215 views5 pages

Lec 13

The document provides information about fluidized catalytic cracking (FCC) units used in petroleum refineries. It discusses the key components and reactions that occur in FCC units. FCC units upgrade heavy petroleum streams like vacuum gas oil into more valuable products like gasoline and light olefins. The process involves circulating a zeolite catalyst between a riser reactor, where cracking reactions take place, and a regenerator, where coke is burned off the catalyst to regenerate it. Typical feedstocks and products of FCC units are also described.

Uploaded by

Ghazy alshyal
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Petroleum Refining Fourth Year Dr.Aysar T.

Jarullah

Catalytic Operations
Fluidized Catalytic Cracking
The fluidized catalytic cracking (FCC) unit is the heart of the refinery and is where heavy
low-value petroleum stream such as vacuum gas oil (VGO) is upgraded into higher value
products, mainly gasoline and C3/C4 olefins, which can be used in the alkylation unit for
production of ultra-clean gasoline (C7 – C8 alkylates). The FCC unit mainly depends on
circulating a zeolite catalyst with the vapor of the feed into a riser-reactor for a few seconds.
The cracked products are disengaged from the solids and taken out to a distillation column
for separation of the desired products. The catalyst is circulated back into the regenerator
where coke is burned and the catalyst regenerated.

Feedstock and Products


The main feedstock used in a FCC unit is the gas oil boiling between 316 °C and 566 °C (600
F and 1050 F). This gas oil can be considered mixtures of aromatic, naphthanic and paraffinic
molecules. Gas oil from residue and conversion processes (predominantly coking) can be fed
to catalytic cracking units. They must be hydrotreated before catalytic cracking to separate
aromatics and remove sulphur.
The principal limitation on charge stocks are the Conradson Carbon Residue (CCR) and
metal contaminants. The effect of Conradson carbon is to form a deposit on the catalyst. This
deposit could be beyond the burning capacity in the regenerator. For atmospheric residue, it
is desulphurized first in the ARDS unit. Vacuum residue must also desulphurized and may be
deasphalted before used in the FCC.
Some possible feedstocks are atmospheric distillates, coking distillates, visbreaking
distillates, VGO, atmospheric residue (desulphurized) and vacuum residue (desulphurized,
deasphalted). Typical feedstock properties are given in Table A1. In addition, products with
their corresponding yields and characteristics are shown in Table A2.
Petroleum Refining Fourth Year Dr.Aysar T. Jarullah

FCC Reactions
The main reaction in the FCC is the catalytic cracking of paraffin, olefins, naphthenes and
side chains in aromatics. The main reactions in the FCC reactor can be summarized as
follows:
Petroleum Refining Fourth Year Dr.Aysar T. Jarullah

FCC Catalyst
The main catalyst which is used in a FCC reactor is the zeolite type. It is in a powderform
with an average particle size of 75 µm and an average surface area of 800 m2/g.

Process Description
The basic configuration of the FCC unit is a reactor (riser) and a regenerator. The catalyst is
circulated between them where it is deactivated in the riser and regenerated in the
regenerator. The process flow diagram for FCC unit is shown in Figure below. Steam and
VGO heated up to 316–427 °C (600–800 F) are fed to the bottom of the riser, which is a long
vertical pipe. The regenerated hot catalyst at 649–760 °C (1200–1400 F) is also fed to the
bottom of the riser. The riser is the main reactor in which the endothermic reactions take
place. The residence time in the riser is 2–10 s. At the top of the riser, the gaseous products
flow into the fractionator, while the catalyst and some heavy liquid hydrocarbon flow back in
the disengaging zone. Steam is injected into the stripper section, and the oil is removed from
the catalyst with the help of some baffles installed in the stripper. The oil is stripped in this
way from the catalyst and the spent catalyst is sent to the regenerator at a temperature of 482–
538 °C (900–1000 F). The coke in the spent catalyst is burned off in the regenerator by
introducing excess air, which is used to ensure the efficient combustion of coke.
In both the reactor and the regenerator, hydrocyclones are installed to catch any solid
particles carried out in the overheated stream. The product gases from the reactor are sent to
the fractionator which produces light gases, heavy gasoline (main product), light cycle gas oil
(LCO), heavy cycle gas oil (HCO) and decant slurry. The light gases are sent to the gas
concentration unit where flue gas, propane, butane, LPG and light gasoline are produced. The
operating conditions are usually adjusted to produce the maximum amount of gasoline from
the VGO.
Petroleum Refining Fourth Year Dr.Aysar T. Jarullah

FCC Yield Correlations


The yield correlations given in Table below require target conversion (LV%), feed API and
sulphur in the feed. Conversion is defined as the percentage of the oil fed that has been
cracked into lighter fractions than gasoline and lighter products:

The recycle stock is the portion of the feedstock which is not cracked to fractions lighter than
gasoline. For example, for 75% conversion, the cycle stock is 25%.

Example:
A feed of 20,000 BPD of AGO (650–850 F) having an API of 24 and a sulfur content of 0.2
wt%, is mixed with another of feed of 15,000 BPD of VGO (850–1050 F) that has an API of
15 and a sulfur content of 0.35 wt%. They are used as a feed to FCC unit. Use the FCC
correlations to find the material balance around the reactor unit. Assume a conversion of 75
LV%.
Petroleum Refining Fourth Year Dr.Aysar T. Jarullah

This gives feed API = 20.02. The results and product properties can be calculated as shown in
Table below.

You might also like