Scribd
Upload
2K views

Example PMOS Circuit Analysis

The document analyzes a PMOS circuit to determine the unknown voltage VGG. It first assumes the PMOS is in saturation, but the calculations show this assumption is incorrect. Assuming triode region instead, the calculations yield VGG = 0V, and checks confirm this assumption is correct. The key steps are making assumptions, analyzing the circuit equations, solving for the unknown VGG, and checking the assumptions.

Uploaded by

Gaurav Panchanan
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
2K views

Example PMOS Circuit Analysis

The document analyzes a PMOS circuit to determine the unknown voltage VGG. It first assumes the PMOS is in saturation, but the calculations show this assumption is incorrect. Assuming triode region instead, the calculations yield VGG = 0V, and checks confirm this assumption is correct. The key steps are making assumptions, analyzing the circuit equations, solving for the unknown VGG, and checking the assumptions.

Uploaded by

Gaurav Panchanan
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 8

10/22/2004 Example PMOS Circuit Analysis.

doc 1/8

Example: PMOS Circuit


Analysis
Consider this PMOS circuit: 5V
K = 0.2 mA/V2

Vt = -2.0 V

10 K
+ VD=4.0V
VGG ID
-
4K

For this problem, we know that the drain voltage VD = 4.0 V


(with respect to ground), but we do not know the value of the
voltage source VGG.

Let’s attempt to find this value VGG !

First, let’s ASSUME that the PMOS is in saturation mode.

Therefore, we ENFORCE the saturation drain current


equation ID = K (VGS −Vt ) .
2

Jim Stiles The Univ. of Kansas Dept. of EECS


10/22/2004 Example PMOS Circuit Analysis.doc 2/8

5V
Now we must ANALYZE this circuit!

Q: Yikes! Where do we start ? IG

A: The best way to start is VD=4.0V


10 K
by “picking the low-hanging +
fruit”. In other words, VGG ID
-
determine the obvious and 4K
easy values. Don’t ask,
“What is VGG?”, but instead
ask, “What do I know?” !

There are lots of things that we can quickly determine about


this circuit!

IG = 0.0 mA

VS = 5.0 V

VD − 0 4.0 − 0
ID = = = 1 mA
4 4

VG =VGG − 10 IG =VGG − 10 ( 0 ) = VGG

Therefore, we can likewise determine:

VDS =VD −VS = 4.0 − 5.0 = −1.0 V

VGS =VG −VS = VGG − 5.0 V

Jim Stiles The Univ. of Kansas Dept. of EECS


10/22/2004 Example PMOS Circuit Analysis.doc 3/8

Note what we have quickly determined—the numeric value of


drain current (ID=1.0 mA) and the voltage drain-to-source
(VDS =-1.0) Moreover, we have determined the value VGS in
terms of unknown voltage VGG (VGS = VGG − 5.0 ).

We’ve determined all the important stuff (i.e., VGS ,VDS , ID ) !

We can now relate these values using our PMOS drain current
equation. Recall that we ASSUMED saturation, so if this
assumption is correct:

ID = K (VGS −Vt )
2

Inserting into this equation our knowledge from above, along


with our PMOS values K=0.2 mA/V2 and Vt=-2.0, we get:

ID = K (VGS −Vt )
2

1.0 = 0.2 (VGS − ( −2.0 ) )


2

5.0 = (VGS + 2.0 )


2

Be careful here! Note in the above equation that threshold


voltage Vt is negative (since PMOS) and that ID and K are both
written in terms of milliamps (mA).

Now, we solve this equation to find the value of VGS !

Jim Stiles The Univ. of Kansas Dept. of EECS


10/22/2004 Example PMOS Circuit Analysis.doc 4/8

5.0 = (VGS + 2.0 )


2

± 5 = VGS + 2.0
± 5 − 2.0 = VGS

Q: So VGS is both 5 − 2.0 = 0.24 V and − 5 − 2.0 = −4.23V ?


How can this be possible?

A: It’s not possible! The solution is either VGS=0.24 V or VGS


= -4.23 V.

Q: But how can we tell which solution is correct?

A: We must choose a solution that is consistent with our


original ASSUMPTION. Note that neither of the solutions
must be consistent with the saturation ASSUMPTION, an
event meaning that our ASSUMPTION was wrong.

However, one (but only one!) of the two solutions may be


consistent with our saturation ASSUMPTION—this is the
value that we choose for VGS!

For this example, where we have ASSUMED that the PMOS


device is in saturation, the voltage gate-to-source VGS must be
less (remember, it’s a PMOS device!) than the threshold
voltage:
VGS <Vt
VGS < −2.0 V

Jim Stiles The Univ. of Kansas Dept. of EECS


10/22/2004 Example PMOS Circuit Analysis.doc 5/8

Clearly, one of our solutions does satisfy this equation


(VGS = −4.23 < −2.0 ), and therefore we choose the solution
VGS = −4.23V .

Q: Does this mean our saturation ASSUMPTION is correct?

A: NO! It merely means that our saturation ASSUMPTION


might be correct! We need to CHECK the other inequalities
to know for sure.

Now, returning to our circuit analysis, we can quickly


determine the unknown value of VGG. Recall that we earlier
determined that:
VGS =VGG − 5.0

And now, since we “know” that the VGS=-4.23 V, we can


determine that:
VGG =VGS + 5.0
= −4.23 + 5.0
= 0.77 V

This solution (VGG=0.77 V) is of course true only if our original


ASSUMPTION was correct. Thus, we must CHECK to see if
our inequalities are valid:

We of course already know that the first inequality is true—a


p-type channel is induced:

VGS = −4.23 < −2.0 = Vt

Jim Stiles The Univ. of Kansas Dept. of EECS


10/22/2004 Example PMOS Circuit Analysis.doc 6/8

And, since the excess gate voltage is VGS −Vt = −2.23 V , the
second inequality:

VDS = −1.0 > −2.23 = VGS −Vt

shows us that our ASSUMPTION was incorrect!

Æ Time to make a new ASSUMPTION and start over!

So, let’s now ASSUME the PMOS device is in triode region.

Therefore ENFORCE the drain current equation:

iD = K ⎡⎣2 (VGS −Vt )VDS −VDS2 ⎤⎦

Now let’s ANALYZE our circuit!

Note that most of our original analysis was independent of


our PMOS mode ASSUMPTION. Thus, we again conclude
that:

IG = 0.0 mA

VS = 5.0 V

VD − 0 4.0 − 0
ID = = = 1 mA
4 4

VG =VGG − 10 IG =VGG − 10 ( 0 ) = VGG

Jim Stiles The Univ. of Kansas Dept. of EECS


10/22/2004 Example PMOS Circuit Analysis.doc 7/8

Therefore,

VDS =VD −VS = 4.0 − 5.0 = −1.0 V

VGS =VG −VS = VGG − 5.0 V

Now, inserting these values in the triode drain current


equation:
iD = K ⎡⎣2 (VGS −Vt )VDS −VDS2 ⎤⎦
1.0 = 0.2 ⎡2 (VGS − ( −2 ) ) ( −1 ) − ( −1 ) ⎤
2
⎣ ⎦
5.0 = ⎡⎣ −2 (VGS + 2 ) − 1⎤⎦

Look! One equation and one unknown! Solving for VGS we find:

5.0 = ⎡⎣ −2 (VGS + 2 ) − 1⎤⎦


6.0 = −2 (VGS + 2 )
−3.0 = VGS + 2
−5.0 = VGS

Thus, we find that VGS = -5.0 V, so that we can find the value
of voltage source VGG :

VGS =VGG − 5.0


−5.0 = VGG − 5.0
0.0 = VGG

The voltage source VGG is equal to zero—provided that our


triode ASSUMPTION was correct.

Jim Stiles The Univ. of Kansas Dept. of EECS


10/22/2004 Example PMOS Circuit Analysis.doc 8/8

To find out if the ASSUMPTION is correct, we must CHECK


our triode inequalities.

First, we CHECK to see if a channel has indeed been induced:

VGS = −5.0 < −2.0 = Vt

Next, we CHECK to make sure that our channel is not in pinch-


off. Noting that the excess gate voltage is
VGS −Vt = −5.0 − ( − 2.0) = −3.0V , we find that:

VDS = −1.0 > −3.0 = VGS −Vt

Our triode ASSUMPTION is correct! Thus, the voltage


source VGG = 0.0 V.

Jim Stiles The Univ. of Kansas Dept. of EECS

You might also like