MSMC104+: Technical User'S Manual For

TECHNICAL USER'S MANUAL FOR:
PC/104 and peripheral board
MSMC104+
Nordstrasse 11/F
CH- 4542 Luterbach
Tel.: ++41 (0)32 681 58 00
Fax: ++41 (0)32 681 58 01
Email: [email protected]
Homepage: http://www.digitallogic.com
DIGITAL-LOGIC AG MSMC104+ Manual V1.0
COPYRIGHT  1992-2006 BY DIGITAL-LOGIC AG

No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, in any
form or by any means, electronic, mechanical, optical, manual, or otherwise, without the prior written
permission of DIGITAL-LOGIC AG.
The software described herein, together with this document, are furnished under a license agreement and
may be used or copied only in accordance with the terms of that agreement.
Any information in this manual and of the product are subject to change without notice.
REVISION HISTORY:
Product Document Date/Vis: Modification:
Version Version Remarks, News, Attention:
V0.3 V1.0 01.2006 DAR Initial Version
Registration:
http://www.digitallogic.com -> SUPPORT -> embedded support -> login
After registration, you will receive driver & software updates, errata information, customer information and
news from DIGITAL-LOGIC AG products automatically.
2
Table of Contents
1 PREFACE............................................................................................................................ 4
1.1 HOW TO USE THIS MANUAL....................................................................................................................4
1.2 TRADEMARKS .......................................................................................................................................4
1.3 DISCLAIMER ..........................................................................................................................................4
1.4 W HO SHOULD USE THIS PRODUCT .........................................................................................................4
1.5 RECYCLING INFORMATION .....................................................................................................................5
1.6 TECHNICAL SUPPORT ............................................................................................................................5
1.7 LIMITED W ARRANTY ..............................................................................................................................5
2 OVERVIEW ......................................................................................................................... 6
2.1 ORDERING INFORMATION ......................................................................................................................6
2.2 GENERAL INFORMATION ........................................................................................................................7
CONNECTOR DESCRIPTION ................................................................................................... 8
3 JUMPER DESCRIPTION................................................................................................... 10
4 DRIVER INSTALLATION .................................................................................................. 11

4.1 INSTALLATION UNDER W INDOWS 98.....................................................................................................11
4.1.1 Installation of the Hardware.......................................................................................................11
4.1.2 First Installation of the Driver.....................................................................................................11
4.1.3 Updating an Existing Installation................................................................................................12
4.1.4 Testing the Driver Installation ....................................................................................................14
4.2 INSTALLATION UNDER W INDOWS 2000.................................................................................................15
4.3 INSTALLATION UNDER W INDOWS XP....................................................................................................20
4.4 CAN DRIVER CONFIGURATION TOOL ...................................................................................................25
4.5 CHECKING THE OPERATION OF THE HARDWARE ...................................................................................26
4.6 TROUBLESHOOTING W INDOWS 98/2000/XP INSTALLATIONS ................................................................26
4.6.1 Verifying the Correct Installation of the MSMC104+ Device Drivers .........................................26
4.6.2 Correcting an Unsuccessful Installation of the MSMC104+ Device Driver................................26
5 DIMENSIONS .................................................................................................................... 27
6 INDEX................................................................................................................................ 28
3
1 PREFACE
This manual is for integrators and programmers of systems based on the MICROSPACE card family. It
contains information on hardware requirements, interconnections, and details of how to program the
system. The specifications given in this manual were correct at the time of printing; advances mean that
some may have changed in the meantime. If errors are found, please notify DIGITAL-LOGIC AG at the
address shown on the title page of this document, and we will correct them as soon as possible.
1.1 How to use this Manual

This manual is written for the original equipment manufacturer (OEM) who plans to build computer
systems based on the single board MICROSPACE-PC. It provides instructions for installing and
configuring the MSM486SL or MSM386SN board, and describes the system and setup requirements.
1.2 Trademarks
Chips & Technologies SuperState R
MICROSPACE, MicroModule DIGITAL-LOGIC AG
DOS Vx.y, Windows Microsoft Inc.
PC-AT, PC-XT IBM
NetWare Novell Corporation
Ethernet Xerox Corporation
DR-DOS, PALMDOS Digital Research Inc. / Novell Inc.
ROM-DOS Datalight Inc.
1.3 Disclaimer
DIGITAL-LOGIC AG makes no representations or warranties with respect to the contents of this manual
and specifically disclaims any implied warranty of merchantability or fitness for any particular purpose.
DIGITAL-LOGIC AG shall under no circumstances be liable for incidental or consequential damages or
related expenses resulting from the use of this product, even if it has been notified of the possibility of
such damage. DIGITAL-LOGIC AG reserves the right to revise this publication from time to time without
obligation to notify any person of such revisions. If errors are found, please contact DIGITAL-LOGIC AG at
the address listed on the title page of this document.
1.4 Who should use this Product

- Electronic engineers with know-how in PC-technology.
- Without electronic know-how we expect you to have questions. This manual assumes, that you have a
general knowledge of PC-electronics.
- Because of the complexity and the variability of PC-technology, we can’t give any warranty that the
product will work in any particular situation or combination. Our technical support will help you to may
find a solution.
- Pay attention to the electrostatic discharges. Use a CMOS protected workplace.
- Power supply OFF when you are working on the board or connecting any cables or devices.
This is a high technology product.

You need know-how in electronics and PC-technology
to install the system !
4
1.5 Recycling Information
Hardware:
- Print: epoxy with glass fiber
wires are of tin-plated copper
- Components: ceramics and alloys of gold, silver

check your local electronic recycling
Software:
- no problems: re-use the diskette after formatting
1.6 Technical Support

1. Contact your local Digital-Logic Technical Support in your country.
2. Use Internet Support Request form on http://www.digitallogic.com -> support -> support request form
3. Send a FAX or an E-mail to DIGITAL-LOGIC AG with a description of your problem.

DIGITAL-LOGIC AG
smartModule DesignIn Center
Nordstr. 11/F
CH-4542 Luterbach (SWITZERLAND)
Fax: ++41 32 681 58 01
E-Mail: [email protected]
Internet www.digitallogic.com
Support requests will only be accepted with detailed informations about the product (BIOS-, Board-
version) !
1.7 Limited Warranty

DIGITAL-LOGIC AG warrants the hardware and software products it manufactures and produces to be
free from defects in materials and workmanship for one year following the date of shipment from
DIGITAL-LOGIC AG, Switzerland. This warranty is limited to the original purchaser of product and is not
transferable.
During the one year warranty period, DIGITAL-LOGIC AG will repair or replace, at its discretion, any
defective product or part at no additional charge, provided that the product is returned, shipping prepaid,
to DIGITAL-LOGIC AG. All replaced parts and products become property of DIGITAL-LOGIC AG.
Before returning any product for repair, customers are required to contact the company or their distributor.
This limited warranty does not extend to any product which has been damaged as a result of accident,
misuse, abuse (such as use of incorrect input voltages, wrong cabling, wrong polarity, improper or
insufficient ventilation, failure to follow the operating instructions that are provided by DIGITAL-LOGIC AG
or other contingencies beyond the control of DIGITAL-LOGIC AG), wrong connection, wrong information
or as a result of service or modification by anyone other than DIGITAL-LOGIC AG. Neither, if the user has
not enough knowledge of these technologies or has not consulted the product manual or the technical
support of DIGITAL-LOGIC AG and therefore the product has been damaged.
Except, as expressly set forth above, no other warranties are expressed or implied, including, but not
limited to, any implied warranty of merchantability and fitness for a particular purpose, and DIGITAL-
LOGIC AG expressly disclaims all warranties not stated herein. Under no circumstances will DIGITAL-
LOGIC AG be liable to the purchaser or any user for any damage, including any incidental or
consequential damage, expenses, lost profits, lost savings, or other damages arising out of the use or
inability to use the product.
5
2 OVERVIEW
2.1 Ordering Information
Ordering Information:
MSMC104+ (801645)
Overview Piggies
Piggy Transceiver Description

LINpigggy 6259opto TLE6259 LIN with opto coupler
CANpigggy 251 82C251 CAN High-Speed
CANpigggy 1050 TJA1050 CAN High-Speed
CANpigggy 251opto 82C251 CAN High-Speed with opto coupler
CANpigggy 1050opto TJA1050 CAN High-Speed with opto coupler
CANpigggy 1041opto TJA1041 CAN High-Speed with opto coupler
CANpigggy 1054 TJA1054 CAN Low-Speed
CANpigggy 1054opto TJA1054 CAN Low-Speed with opto coupler
CANpiggy 10011opto B10011S Truck applications with opto coupler
CANpigggy 5790 c AU5790 CAN Single-Wire
CANpigggy 5790opto c AU5790 CAN Single-Wire with opto coupler
Figure 6: CANpiggy 251
More information and an updated list of all available piggies can be found under
http://www.vector-informatik.de.
6
2.2 General Information

The product MSMC104+ can be described as following:
Based on the high-performance microcontroller and the flexible hardware design, the MSMC104+ card is
well suited for present and future applications.
BUS:
Standard: PC/104+
Size and Type: PCI multiplexed 32 Bit Address/Data Bus
Controller:
Type: 32-bit microcontroller with 64MHz
Power Supply:
Power supply: 5V through PCI Bus
3.3V through PCI Bus
Interfaces:
CAN 2.0B and LIN 2 completely independent channels
BUS transceiver as plug-in boards

(Piggies)
Physical Characteristics:
Dimensions: Length: 90mm
Width: 96mm
Height: 15mm
Operating Environment:
Relative humidity: 5 - 90% non condensing
Vibration: 5 to 2000 Hz
Shock: 10g
Temperature: Operating: -25°C to +70°C
Storage: -55°C to +85°C
Power Managers
Many desktop PC's have power managers. Power managers disable the CPU for a certain amount of
time. This impairs time management accuracy in your application. If you have stringent requirements for
your application time management (time-driven transmission of messages, time-driven evaluations), you
must deactivate these power managers. Options for power management may be included in:
• The BIOS setup,
• The Windows 98/2000/XP Control Panel (e.g. Power object).
7
CONNECTOR DESCRIPTION
8
X553 / 583 D-Sub 9 Termianl Assignement
Function for the different piggies

Onboard
D-Sub 9
header
LIN 251 251opto 1041 1054 1054 10011 5790 C 5790

6259 1050 1050opt opto opto opto (Single opto C
o Wire )
1 1 N.C. N.C. N.C. N.C. N.C. N.C. N.C. N.C. N.C.

3 2 N.C. CAN CAN CAN CAN CAN CAN N.C. N.C.
Low Low Low Low Low Low
5 3 VB- GND VB- VB- GND VB- VB- GND VB-
7 4 Pdis RL N.C. Split RL N.C. RL R100 R100
9 5 Shield Shield Shield Shield Shield Shield Shield Shield Shield

2 6 RL RL RL RL RL RL RL RL RL
4 7 LIN CAN CAN CAN CAN CAN CAN CAN CAN
High High High High High High
6 8 RL RL RL RL RL RL RL RL RL
8 9 VB+ N.C. N.C. VB+ N.C. VB+ VB+ VB+ V_Batt
optional optional optional 16-32 V optional
11-18 V 11-18 V 11-18 V 11-18 V
Shield: shield
GND: mass
V_Batt : battery voltage (+12 V referred to GND, extern)
N.C.: not connected
RL: reserved lines, not to be connected to any cable
VB+: positive supply voltage, optically decoupled
VB-: galvanic decoupled mass
R100: If the single wire CANpiggy is used in a high-speed net, there has to be a termination
resistor between CAN High and GND. This termination resistor is enabled in Fast Mode
by the CANpiggy itself, if CAN High (pin 7) and pin 4 are connected by a bridge.
Pdis: If this pin of the LINpiggy is connected to GND (pin 3), the internal voltage supply is
switched off.
9
3 JUMPER DESCRIPTION
J210 PCI-IDSEL Source open close

1-2 none ID 0
3-4 none ID 1
5-6 none ID 2
7-8 none ID 3
Only one of this selection may be closed. Use a signal, which is not used by another board.
J211 PCI-IRQ Source open close

1-2 none IRQ A
3-4 none IRQ B
5-6 none IRQ C
7-8 none IRQ D
J212 PCI-Bus Clocksource open close

1-2 none PCICLK 0
3-4 none PCICLK 1
5-6 none PCICLK 2
7-8 none PCICLK 3
* = Default
10
4 DRIVER INSTALLATION
4.1 Installation under Windows 98

This chapter will give some comments and tips for your first installation of the driver as well as for updating
already installed drivers for Windows 98.
4.1.1 Installation of the Hardware
Note: Please observe all safety precautions prescribed by your PC manufacturer for card
installation!
1. Shut down your PC and all peripheral devices with which it is connected.
2. Pull out the power plug. Open the housing.
3. Before performing the installation, equalize voltage potentials by touching the CANboardXL and the
PC chassis simultaneously.
4. Mount the card in an available PCI slot.
4.1.2 First Installation of the Driver
This described installation procedure is necessary, if no driver was installed so far.
1. After installation of the hardware and rebooting, Windows 98 will automatically start the New
Hardware Found wizard (Figure 1). Please follow its instructions.
2. Choose Search for the best driver for your device (Recommended) (Figure 2).
Figure 1: Add New Hardware Wizard
Figure 2: Choosing the way of driver installation
11
3. The Windows Add New Hardware Wizard needs to be informed about the location of the driver by
choosing Specify a location and by locating the driver by clicking the [Browse…] button.
Figure 3: Specifying the driver location
4. Afterwards press the [Next] button. Please follow the instructions of Windows.
5. The assistant will finish its work with a special confirmation message (Figure 4).
6. Reboot your computer.
7. Check for a successful installation referring to chapter 2.4 for more details.
Figure 4: Completing the Found New Hardware Wizard
4.1.3 Updating an Existing Installation

A driver update must be done if an older version of CANboardXL driver has already been installed on the
computer. You can find the current driver version under Control Panel | Vector Hardware in the section
Hardware | CANboardXL (chapter 5).
1. Start the Windows Device Manager (Start | Settings | Control Panel | System | Device
Manager) (Figure 8).
2. Choose the Driver-tab of the entry Vector CANboardXL (CAN Hardware | Vector CANboardXL |
Properties | Driver).
3. Select [Update Driver…] (Figure 5).
4. Windows 98 will start the wizard for updating the device driver. Please follow its instructions.
5. Choose Display a list of all the drivers in a specific location, so you can select the driver you
want. (Figure 6).
6. Then mark the CANboardXL entry and click the [Have Disk…] button. You have to specify the
location of the device driver. Afterwards press the [Next] button. Please follow the instructions of
Windows.
7. The assistant will finish its work with a special confirmation message.
12
Figure 5: Properties
Figure 6: Update Hardware Device Driver
Figure 7: Upgrade Device Driver Wizard
13
4.1.4 Testing the Driver Installation
Figure 8: System Properties
1. Start the Device Manager (Start | Settings | Control Panel | System | Device Manager) (Figure
5).
2. Check to see whether the Vector CANboardXL device has been entered as a subgroup of the
CAN-Hardware device (Figure 5).
3. Verify the CANboardXL installation by double clicking on the Vector CANboardXL entry. After a
successful driver installation you will get the device status as This device is working properly on
the General index tab (Figure 6).
4. More detailed comments and tips about devices causing conflicts can be found in chapter 7.
5. You can now conduct a function test for the hardware as described in chapter 6.
Figure 9: MSMC104+ Properties
14
4.2 Installation under Windows 2000

already installed drivers for Windows 2000.
Note: It is strongly recommended to use Windows 2000 with Service Pack 4 or later.
Note: Microsoft does not sign the MSMC104+ driver. If during the driver installation a message
appears, which refer to that signature, press the [Yes] button and continue the installation
Note: Note, that an Administrators Account is required for the following steps.
installation!
3. Before performing the installation, equalize voltage potentials by touching the MSMC104+ and the
4. Mount the card in an available slot.
1. After installation of the hardware and rebooting, Windows 2000 will automatically start the New
2. Choose Search for a suitable driver for my device (recommended). Afterwards press the [Next]
button. (Figure 11).
3. The Windows installation wizard has to be informed about the driver location by activating Specify a
location. Afterwards press the [Next] button (Figure 12).
4. Press [Browse] and afterwards the [OK] button. Please follow the instructions of Windows.
Figure 10: Found New Hardware Wizard
15
Figure 11: Install Hardware Device Driver
Figure 12: Locate Driver Files
16

A driver update must be done if an older version of MSMC104+ driver has already been installed on the
computer. You can find the current driver version under Control Panel | Vector Hardware in the section
1. Start the Windows Device Manager (Start | Settings | Control Panel | System | Hardware |
Device Manager) (Figure 18).
2. Choose the Driver-tab of Vector CANboardXL (CAN Hardware | Vector CANboardXL |
Properties).
4. Windows 2000 will start the wizard for updating the device driver. Please follow its instructions.
5. Choose Display a list of the known drivers for this device so that I can choose a specific
driver (Figure 15).
6. Then mark the CANboardXL entry and click the [Have Disk…] button. You have to specify the
location of the device driver.
17
1. Start the Device Manager (Start | Settings | Control Panel | System | Hardware | Device
Manager) (Figure 17).
entry CAN-Hardware (Figure 17).
3. Verify the MSMC104+ installation by double clicking on the Vector CANboardXL entry. After a
successful driver installation you will get the device status This device is working properly on the
General index tab (Figure 18).
Figure 17: Device Manager
18
19
4.3 Installation under Windows XP

already installed drivers for Windows XP. All required files can be found on the installation CD.
Note: Depending on the chosen view the Windows XP Device Manager can be started as following:
Category View: Start | Control Panel | Performance and Maintenance | System |

Hardware | Device Manager
Classic View: Start | Control Panel | System | Hardware | Device Manager
Note: Microsoft does not sign the MSMC104+ driver. If during the driver installation a message
appears, which refer to that signature, press the [Yes] button and continue the installation
Note: Note, that an Administrators Account is required for the following steps.
Note: The PXI version of the CANboardXL is recognized as CANboardXL pxi under Windows XP.
installation!
3. Before performing the installation, equalize voltage potentials by touching the MSMC104+ and the
4. Mount the card in an available slot.
1. After installation of the hardware and rebooting, Windows XP will automatically start the New
2. Choose Install from a list or specific location (Advanced). Afterwards press the [Next] button.
(Figure 19).
3. The Windows installation wizard has to be informed about the driver location by activating Include
this location in the search:
20
Figure 19: Found New Hardware Wizard
Figure 20: Install Hardware Device Driver
21

A driver update must be done if an older version of MSMC104+ driver has already been installed on the
computer. You find the current driver version under Control Panel | Vector Hardware in the section
1. Start the Windows Device Manager (Start | Settings | Control Panel | System | Hardware |
Device Manager) (Figure 25).
2. Choose the Driver tab of Vector CANboardXL (CAN Hardware | Vector CANboardXL |
Properties).
4. Windows XP will start the wizard for updating the device driver (Figure 16).
5. Choose Install from a list or specific location (Advanced) and follow the instructions of the
wizard (Figure 23).
6. The wizard has to be informed about the driver location by activating Include this location in the
search:.
Figure 22: Vector MSMC104+ Properties
Figure 23: Hardware Update Wizard
22
Figure 24: Choose search and installation options
23
Figure 25: Device Manager
1. Start the Device Manager (Figure 25).

entry CAN Hardware (Figure 25).
3. Verify the MSMC104+ installation by double clicking on the Vector CANboardXL entry. After a
successful driver installation you will get the device status This device is working properly on the
General index tab (Figure 26).
24
4.4 CAN Driver Configuration Tool

After installing the driver successfully, you will find the icon Vector Hardware located in the Control Panel
(Start | Settings | Control Panel).
Note: Depending on the chosen view on Windows XP, the Vector Hardware Configuration Tool can
be started as following:
Under Start | Settings | Control Panel you will see a window on the left side called Control
panel Please select the issue Switch to classic view. Open the CAN Driver Configuration
Tool with the icon Vector Hardware.
Under Start | Settings | Control Panel you will see a window on the left side called See
also. Please select the issue Other Control Panel Options. Open the Vector Hardware
Configuration Tool with the icon Vector Hardware.
Hardware
The Hardware section shows all installed Vector hardware and the application assignment in a tree like
view. The tree view shows the adapters on the lowest level. Above you will find the CAN channels of the
particular hardware. At last the application assignments are visible.
Application
The Application section shows all available application with configured channels. You can click on
application to see all its channels.
General information
The General information section contains overall settings of Vector devices and applications.
License
The License section contains information about all currently available licenses. You can check for which
tools and applications you have currently present licensed hardware.
Note: You can find a detailed description of the components of CAN Hardware in the Online Help
under Help | Contents.
25
4.5 Checking the Operation of the Hardware

A test to check the correct operation of the driver and hardware may be performed as described below.
This test is identical for Windows 2000 and Windows XP and is application independent. Verification of
hardware operation may also be conducted through the application.
Test of hardware and driver with Loop3.exe program:
For this function test two CAN Transceivers of the same Bus type are necessary (e.g. two Highspeed or
two Lowspeed).
1. If two Highspeed Transceivers (e.g. CANpiggy 251 oder CANpiggy 1041opto) are used, then the
two connections of the CANboardXL/pxi hardware - Channel1 and Channel2 - must be connected
with a CANcable1. With Lowspeed Transceiver use CANcable0.
2. This test program will access the card and send CAN messages.
3. Mark Channel1 and Channel2 of the hardware, which should be tested (Selected channels).
4. Adjust the appropriate baud rate (Settings) depending on the Transceiver used (Highspeed max:
1.000.000 Bd, Lowspeed max: 125.000 Bd).
5. Press the [Start] button.
6. If the system is configured correctly, statistic data of the hardware used appears in the lower
window of the test software (Figure 28).
7. By pressing the [Stop] button the test procedure stops and in the upper window a successful test is
confirmed with an OK message.
4.6 Troubleshooting Windows 98/2000/XP Installations

4.6.1 Verifying the Correct Installation of the MSMC104+ Device Drivers
For the execution of the following test units the MSMC104+ must be built in into the PC.
Open the Device Manager (Start | Settings | Control Panel | System | (Hardware) | Device Manager).
• Check to see whether the CANboardXL device is registered as a subgroup of the CAN-Hardware
(Windows98/2000/XP). If this device is not registered, either the device driver was not installed
correctly or it was not installed at all. Open the Other components item (it is marked by a yellow ?)
in the Device Manager. The driver has not been installed correctly if you will find the entry Vector
CANboardXL. Correct the driver installation as described in chapter 7.2.
• If you do not find the entries mentioned above, the device driver for the MSMC104+ has not yet
been installed.
4.6.2 Correcting an Unsuccessful Installation of the MSMC104+ Device Driver
The driver was not installed correctly if you find the entry Vector CANboardXL in the Device Manager
under the Other components entry (marked by a yellow ?).
In this case you have to update the driver.
• Open the Device Manager and double-click the line Other components to open it.
• Highlight the entry Vector CANboardXL and click Properties.
• Select the Driver page and click [Driver update…].
• Now follow the Windows instructions using the corresponding driver provided on the installation CD.
26
5 DIMENSIONS
Will follow in a later version of this manual
27
6 INDEX
B O
Bus................................................................... 7 Ordering Information ........................................6
C P
CAN Driver Configuration Tool ...................... 25 PCI-Bus Clocksource .....................................10

Connector description...................................... 8 PCI-IRQ Source .............................................10
Controller ......................................................... 7 Piggy.................................................................6
Power Supply....................................................7
D
T
Dimensions .................................................... 27
Driver installation ........................................... 11 Technical Support ............................................5
Transceiver.......................................................6
I
W
IDSEL ............................................................ 10
Interfaces ......................................................... 7 Windows 2000................................................15
Windows 98....................................................11
J Windows XP ...................................................20
Jumper description ........................................ 10
28

MSMC104+: Technical User'S Manual For

Uploaded by

Copyright:

Available Formats

MSMC104+: Technical User'S Manual For

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

MSMC104+: Technical User'S Manual For

Uploaded by

Copyright:

Available Formats

TECHNICAL USER'S MANUAL FOR:

PC/104 and peripheral board

COPYRIGHT  1992-2006 BY DIGITAL-LOGIC AG

CONNECTOR DESCRIPTION ................................................................................................... 8

4 DRIVER INSTALLATION .................................................................................................. 11

1.1 How to use this Manual

1.4 Who should use this Product

This is a high technology product.

1.5 Recycling Information

- Components: ceramics and alloys of gold, silver

1.6 Technical Support

3. Send a FAX or an E-mail to DIGITAL-LOGIC AG with a description of your problem.

1.7 Limited Warranty

2.1 Ordering Information

Piggy Transceiver Description

Figure 6: CANpiggy 251

2.2 General Information

BUS transceiver as plug-in boards

X553 / 583 D-Sub 9 Termianl Assignement

Function for the different piggies

LIN 251 251opto 1041 1054 1054 10011 5790 C 5790

1 1 N.C. N.C. N.C. N.C. N.C. N.C. N.C. N.C. N.C.

9 5 Shield Shield Shield Shield Shield Shield Shield Shield Shield

J210 PCI-IDSEL Source open close

J211 PCI-IRQ Source open close

J212 PCI-Bus Clocksource open close

4.1 Installation under Windows 98

Figure 1: Add New Hardware Wizard

Figure 2: Choosing the way of driver installation

Figure 3: Specifying the driver location

Figure 4: Completing the Found New Hardware Wizard

4.1.3 Updating an Existing Installation

Figure 6: Update Hardware Device Driver

Figure 7: Upgrade Device Driver Wizard

4.1.4 Testing the Driver Installation

Figure 8: System Properties

Figure 9: MSMC104+ Properties

4.2 Installation under Windows 2000

4.2.1 Installation of the Hardware

Figure 10: Found New Hardware Wizard

Figure 11: Install Hardware Device Driver

Figure 12: Locate Driver Files

Figure 13: Completing the Found New Hardware Wizard

4.2.3 Updating an Existing Installation

Figure 14: Properties

Figure 15: Upgrade Device Driver Wizard

Figure 16: Upgrade Device Driver Wizard

4.2.4 Testing the Driver Installation

Figure 17: Device Manager

Figure 18: Properties

4.3 Installation under Windows XP

Category View: Start | Control Panel | Performance and Maintenance | System |

Classic View: Start | Control Panel | System | Hardware | Device Manager

4.3.1 Installation of the Hardware

Figure 19: Found New Hardware Wizard

Figure 20: Install Hardware Device Driver

Figure 21: Completing the Found New Hardware Wizard

4.3.3 Updating an Existing Installation

Figure 22: Vector MSMC104+ Properties