INSTALLATION/OWNER'S MANUAL AM/FM Receiver with Bluetooth and Fixed Face XDM16BT INSTALLATION
Preparation Please read entire manual before installation.
Before You Start
• Disconnect negative battery terminal. Consult a qualified technician for instructions. • Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration.
Mounting the Head Unit: Single DIN
Typical DIN mounting Dashboard or Installation Kit Step 1: Insert the mounting sleeve into the installation kit or dashboard. Mounting Sleeve
Step 2: Single DIN
Dashboard or Installation Kit Bend multiple mounting tabs around Mounting Sleeve
the mounting sleeve
until the mounting sleeve is secure. Mounting Tabs
Single DIN Step 3: Dashboard or Installation Kit
Connect all wiring Mounting Sleeve
harnesses and slide Head Unit
the head unit into the
mounting sleeve until it clicks into place.
Mounting the Head Unit:
ISO mounting Single DIN Decorative Using the existing Bezel Existing Brackets
brackets or the brackets New
Radio
supplied with the
installation kit, mount the brackets to the sides of the head unit with the screws supplied with the head unit. 2 XDM16BT INSTALLATION
Wiring Diagram
FUSE When replacing the fuse, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the radio. The unit uses one 10 amp ATM fuse located beside the Heat Sink
3 XDM16BT OPERATION
Control Locations 1 2 3 4 5 6
18 17 16 15 14 13 12 11 10 9 8 7
1 Power 7 Auxiliary Input 13 Preset 1 / Play/Pause
2 Band 8 Preset 6 / Folder Up 14 Display
3 Mute 9 Preset 5 / Folder Down 15 Mode
4 Volume Knob 10 Preset 4 / Random 16 Reset
5 Automatically Store 11 Preset 3 / Repeat 17 Tune Up
6 USB Port 12 Preset 2 / Intro 18 Tune Down
1 2
3 1 Mode 10 Preset 6 / Folder Up
4 2 Volume Up 11 Mute 17 3 Power 12 AS/PS 5 16 4 Audio 13 Preset 5 / Folder Down 6 15 5 Tune Up 14 Preset 4 / Random 7 6 Volume Down 15 Preset 1 / Play / Pause 14 8 7 Band 16 Bluetooth Talk 13 9 8 Preset 3 / Repeat 17 Tune Down 12 9 Preset 2 / Intro 10
11
4 XDM16BT OPERATION
General Operation Power On/Off Press the button to turn the unit on. Press again to turn the unit off.
Changing Modes Press MODE to select between Radio, USB, Auxiliary Input and Bluetooth. Modes of operation are shown in the display.
Volume Adjust volume using the volume knob (00-43).
Mute Press to silence the audio. Press again to resume listening
at the previously selected volume.
Auxiliary Inputs Insert a 3.5mm cable in the unit's front AUX port.
Reset Press the RESET button to reset the unit back to the factory settings if abnormal operation occurs. The reset button is located on the front panel.
Setting the Clock With the unit on, press DISP to display clock time. Press and hold DISP until the hours begins to flash, then release.
Press the TUNE nn and TUNE ll to adjust the hours,
then press the DISP, the minutes begins to flash, press the TUNE nn and TUNE ll button to adjust the minutes.
Press DISP momentarily to save the selected time.
Display Press DISP to toggle display between various displayed
information.
Audio / Menu Press the volume knob momentarily to select between audio functions.
Press and hold the volume knob for more than two seconds to select between the menu functions.
Rotate the volume knob left/right to adjust or activate the
desired function/audio.
5 XDM16BT OPERATION
AM/FM Tuner Operation
Seek Tuning Press TUNE nn or TUNE ll to seek to the previous or next strong station.
Manual Tuning Press and hold TUNE nn or TUNE ll to enter manual
tuning mode, then press TUNE nn or TUNE ll momentarily to change radio frequency up or down one step at a time. Press and hold TUNE advance quickly. nn or TUNE ll to
Band Press BAND to select between FM1, FM2, FM3, AM1 and AM2 bands. Up to six presets can be programmed for each band, enabling up to 18 FM stations and 12 AM stations to be stored in memory.
Storing Presets Up to 18 FM and 12 AM stations can be stored. To store
a station, select the desired band and station. Press and hold the desired preset button (1-6) for more than two seconds. When stored, the preset number will appear in the display.
Recalling Presets Preset stations can be recalled any time by pressing the corresponding preset button.
Automatically Store Press and hold AS/PS for more than 2 seconds to store 18 FM stations and 12 AM stations automatically.
Preset Scan Stations Press AS/PS to recall each preset staion that stored in the memories in each band.
6 XDM16BT OPERATION
USB Operation Playing MP3 Files To play MP3 files, insert a USB device containing MP3 files.
Track Select Press TUNE ll to skip to the beginning of the next track. Press TUNE track. nn to skip to the beginning of the previous Fast Forward and Reverse Press and hold TUNE reverse a track. ll or TUNE nn to fast forward or Pause Press Press ll// IIII toagain temporarily stop USB playback. to resume playback.
Folder Access Folders can be found by pressing Folder Up or Folder Down.
About one second after the folder name is displayed, the first file under the selected folder will be displayed and playback will begin.
Repeat Press RPT to toggle between RPT ALL, RPT FLR and RPT ONE. • RPT ALL - Plays all tracks on USB device. • RPT ONE - Continuously repeats selected track. • RPT FLR - Continuously repeats all files in current folder.
Random Press RDM to play tracks in random order; press again to
cancel the RDM function.
Intro Press INT to play the first 10 seconds of each track; press again to cancel the INT function.
7 XDM16BT OPERATION
Bluetooth Operation Preparation Before using a Bluetooth device, it must be paired and connected. Ensure that Bluetooth is activated on your device before beginning the pairing process.
Pairing a New The head unit broadcasts the pairing signal constantly when Device no devices are connected. Complete the pairing sequence from your Bluetooth device. Refer to the owner’s manual for your device for more details.
The device name is “Dual Media Player”.
The Bluetooth passcode is "1234”.
Note: The head unit can be in any mode of operation when
pairing is performed.
Streaming Audio The head unit supports A2DP wireless streaming audio Troubleshooting from a Bluetooth mobile device directly to your head unit. The following functions can be used to control the music:
• Press ll to skip to the next available audio track.
• Press nn to skip to the previous audio track.
l • Press / II to toggle between play and pause during playback.
8 XDM16BT OPERATION
Troubleshooting Problem Cause Action Yellow wire not connected or incorrect Check connections for proper Unit will not turn on voltage Red wire not connected or voltage (11~16VDC) (no power) incorrect voltage Black wire not connected Check connection to ground Fuse blown Replace fuse Speaker wires not connected Check connections at speakers Unit has power Insulate all bare speaker wires (but no sound) One or more speaker wires touching from each other and chassis each other or touching chassis ground ground Yellow or red wire touching chassis Check for pinched wire ground Unit blows fuses Speaker wires touching chassis ground Check for pinched wire Incorrect fuse rating Use fuse with correct rating NO FILE appears No playable MP3 files found Check the device for valid on display on the device MP3 files NO SUPPORT appears Version 1.0 to 2.0 ID3 tags are on display An invalid ID3 tag version is present supported.
9 XDM16BT OPERATION
Limited One Year Warranty
This warranty gives you specific legal What to do? rights. You may also have other rights 1. Before you call for service, check the which vary from state to state. troubleshooting guide in your owner’s manual. A slight adjustment of any Dual Electronics Corp. warrants this custom controls may save you a service product to the original purchaser to be free call. from defects in material and workmanship for a period of one year from the date of 2. If you require service during the the original purchase. warranty period, you must carefully pack the product (preferably in the Dual Electronics Corp. agrees, at our original package) and ship it by prepaid option, during the warranty period, transportation with a copy of the original to repair any defect in material or receipt from the retailer to an workmanship or to furnish an equal authorized service center. new, renewed or comparable product (whichever is deemed necessary) in 3. Please describe your problem in exchange without charges, subject to writing and include your name, a verification of the defect or malfunction and return UPS shipping address (P.O. Box proof of the date of purchase. Subsequent not acceptable), and a daytime phone replacement products are warranted for number with your shipment. the balance of the original warranty period. 4. For more information and for the Who is covered? This warranty is extended location of the nearest authorized to the original retail purchaser for products service center please contact us by one purchased from an authorized Dual dealer of the following methods: and used in the U.S.A. • Call us toll-free at 1-866-382-5476 What is covered? This warranty covers all • E-mail us at [email protected] defects in material and workmanship in this product. The following are not covered: Exclusion of Certain Damages: This software, installation/removal costs, warranty is exclusive and in lieu of any damage resulting from accident, misuse, and all other warranties, expressed or abuse, neglect, product modification, implied, including without limitation the improper installation, incorrect line implied warranties of merchantability and voltage, unauthorized repair or failure fitness for a particular purpose and any to follow instructions supplied with the obligation, liability, right, claim or remedy product, or damage occurring during in contract or tort, whether or not arising return shipment of the product. Specific from the company’s negligence, actual license conditions and copyright notices for or imputed. No person or representative the software can be found via www.dualav. is authorized to assume for the company com. any other liability in connection with the sale of this product. In no event shall the company be liable for indirect, incidental or consequential damages.
10 XDM16BT OPERATION
FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
