Scribd
Upload
281 views2 pages

BYK-P 9065: Processing Additive For Low-Shrink SMC and BMC With Mold Release Properties

Uploaded by

vuqar0979

Copyright:

© All Rights Reserved
Download as PDF, TXT or read online from Scribd
Download as pdf or txt

BYK-P 9065: Processing Additive For Low-Shrink SMC and BMC With Mold Release Properties

Uploaded by

vuqar0979
281 views2 pages

Original Title

TDS_BYK-P_9065_EN.pdf

Copyright

© © All Rights Reserved

Available Formats

PDF, TXT or read online from Scribd

Did you find this document useful?

Is this content inappropriate?

Copyright:

© All Rights Reserved
Download as PDF, TXT or read online from Scribd
Download as pdf or txt
281 views2 pages

BYK-P 9065: Processing Additive For Low-Shrink SMC and BMC With Mold Release Properties

Uploaded by

vuqar0979

Copyright:

© All Rights Reserved
Download as PDF, TXT or read online from Scribd
Download as pdf or txt
You are on page 1/ 2

BYK-P 9065

Data Sheet
Issue 06/2015

BYK-P 9065
Processing additive for low-shrink SMC and BMC with mold release properties.

Product Data

Composition
Combination of surface-active substances and polymers

Typical Properties
The values indicated in this data sheet describe typical properties and do not constitute specification limits.

Acid value: 149 mg KOH/g


Density (20 °C): 0.95 g/ml
Refractive index (20 °C): 1.48
Non-volatile matter (10 min., 150 °C): > 97 %
Flash point: > 100 °C

Food Contact Legal Status


For the current food contact legal status, please contact our product safety department or visit www.byk.com
for further information.

Applications

SMC, BMC

Special Features and Benefits


BYK-P 9065 is a processing additive with mold release properties for low-shrink SMC and BMC. The zinc stearate
that is usually used as a mold release agent is completely replaced by the additive, which simplifies raw material
handling. Separation of the LS-SMC/BMC compounds is avoided and thus cobwebbing is reduced. Scrap rate is
lowered due to reduced shrinkage and less warping. This is supported by higher gloss, lower haze, improved color
homogeneity and a generally higher surface appearance of the finished parts. If the finished parts are to be
painted or bonded, no sanding is required, as BYK-P 9065 is firmly anchored in the cured resin and does not
migrate to the surface. Due to the low dosage of the additive, it is virtually cost neutral.

Einsatzempfehlungen

SMC (LS) X
BMC/DMC Y
X especially recommended Y recommended

BYK-P 9065 is recommended only for LS compounds.


BYK-P 9065

Data Sheet
Issue 06/2015

Recommended Levels
2-2.5 % additive (as supplied) based on the total resin; up to 4 % for very highly filled systems.

The above recommended levels can be used for orientation. Optimal levels are determined through a
series of laboratory tests.

Incorporation and Processing Instructions


Incorporate whilst stirring after the UP resin and LS components have become homogenized.
Traditional release agents should be removed from the formulation.

BYK-Chemie GmbH ANTI-TERRA®, BYK®, BYK®-DYNWET®, BYK®-SILCLEAN®, BYKANOL®, BYKETOL®, BYKJET®, BYKOPLAST®, BYKUMEN®, CARBOBYK®, DISPERBYK®,
P.O. Box 10 02 45 DISPERPLAST®, LACTIMON®, NANOBYK®, PAPERBYK®, SILBYK®, VISCOBYK®, and Greenability® are registered trademarks of BYK-Chemie.
46462 Wesel ACTAL®, ADJUST®, ADVITROL®, ASTRABEN®, BENTOLITE®, CLAYTONE®, CLOISITE®, FULACOLOR®, FULCAT®, GARAMITE®, GELWHITE®,
Germany LAPONITE®, MINERAL COLLOID®, OPTIBENT®, OPTIFLO®, OPTIGEL®, PURE THIX®, RHEOCIN®, RHEOTIX®, RIC-SYN®, TIXOGEL®, and VISCOSEAL®
Tel +49 281 670-0 are registered trademarks of BYK Additives.
Fax +49 281 65735 AQUACER®, AQUAMAT®, AQUATIX®, CERACOL®, CERAFAK®, CERAFLOUR®, CERAMAT®, CERATIX®, HORDAMER®, and MINERPOL®
are registered trademarks of BYK-Cera.
[email protected] SCONA® is a registered trademark of BYK Kometra.
www.byk.com
The information herein is based on our present knowledge and experience. The information merely describes the properties of our products
but no guarantee of properties in the legal sense shall be implied. We recommend testing our products as to their suitability for your envisaged
purpose prior to use. No warranties of any kind, either express or implied, including warranties of merchantability or fitness for a particular
purpose, are made regarding any products mentioned herein and data or information set forth, or that such products, data or information may
be used without infringing intellectual property rights of third parties. We reserve the right to make any changes according to technological
progress or further developments.
This issue replaces all previous versions – Printed in Germany

You might also like