Safety Data Sheet: Chemical Name Cas # Percent Classification Note

Download as pdf or txt
Download as pdf or txt
You are on page 1of 6

Page 1 of 6

FOSTER 81-27 Q
Print Date: 06-01-2015 802389PM
SAFETY DATA SHEET
______________________________________________________________________________
REVISION DATE: 03-16-2015 SUPERSEDES: 02-25-2009

SECTION 1: IDENTIFICATION OF THE PRODUCT AND SUPPLIER

PRODUCT INFORMATION
PRODUCT: FOSTER 81-27 Q
PRODUCT DESCRIPTION: Adhesive
INTENDED USE: Adhesive
PRODUCT IDENTIFIER: 802389PM

COMPANY INFORMATION
H.B. Fuller Construction Products Inc.
1105 S. Frontenac Street
Aurora, IL 60504
Phone: 1-800-552-6225

Medical Emergency Phone Number (24 Hours): 1-888-853-1758


Transport Emergency Phone Number (CHEMTREC): 1-800-424-9300

SECTION 2: HAZARDS IDENTIFICATION


GHS Hazard Symbols:

GHS Signal Word: Danger


GHS Classification: Serious Eye Damage/Eye Irritation Category 1; Skin Corrosion/Irritation Category 2;
Acute Toxicity - Oral Category 4
GHS Hazard Phrases: Harmful if swallowed.; Causes skin irritation.; Causes serious eye damage.
GHS Precautions:
Safety Precautions: Wash thoroughly after handling. Do no eat, drink or smoke when using this product.
Wear protective gloves/protective clothing/eye protection/face protection.
First Aid Measures: IF SWALLOWED: Call a POISON CENTER or doctor/physician if you feel unwell. IF
ON SKIN: Wash with plenty of soap and water. IF IN EYES: Rinse cautiously with
water for several minutes. Remove contact lenses, if present and easy to do. Continue
rinsing. Immediately call a POISON CENTER or doctor/physician. Rinse mouth. If
skin irritation occurs: Get medical advice/attention. Take off contaminated clothing and
wash before reuse.
Disposal: Dispose of contents/container in accordance with local/regional/national/international
regulation for hazardous wastes.

SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS

Chemical Name CAS # PERCENT Classification Note


Sodium silicate 1344-09-8 30 - 50 Acute Tox. 4; H302
Eye Dam. 1; H318
Skin Irrit. 2; H315
*This product contains one or more materials that may be hazardous when present as an airborne dust. During
normal handling of the product, the material is encapsulated within the product and will not present an exposure
risk. Once the product has reached its final state and is abraded or disturbed, dusting and exposure may occur.
Page 2 of 6

FOSTER 81-27 Q
Print Date: 06-01-2015 802389PM
SAFETY DATA SHEET
______________________________________________________________________________
Unlisted ingredients are not 'hazardous' per the Occupational Safety and Health Administration Hazard
Communication Standard (29 CFR 1910.1200) and/or are not found on the Canadian Workplace Hazardous
Materials Information System ingredient disclosure list. See Section 8 for exposure limit guidelines.

SECTION 4: FIRST AID MEASURES

IF IN EYES: Immediately flush eyes with plenty of water for at least 20 minutes retracting eyelids often. This
corrosive material can cause immediate and permanent eye damage. Tilt the head to prevent chemical from
transferring to the uncontaminated eye. Get immediate medical attention and monitor the eye daily as advised by
your physician.
IF ON SKIN: Wash with soap and water. Remove contaminated clothing, launder immediately, and discard
contaminated leather goods. Get medical attention immediately.
IF INHALED: Remove to fresh air. Restore breathing, if necessary. Keep warm and quiet. Call a physician.
IF SWALLOWED: Corrosive. Do not induce vomiting! Drink one glass of water followed by milk if available.
Seek medical attention immediately. Do not give anything by mouth to an unconscious person. Induced vomiting
may lead to aspiration of the material into the lungs potentially causing chemical pneumonitis that may be fatal.

SECTION 5: FIRE FIGHTING MEASURES

EXTINGUISHING MEDIA: Use water spray, foam, dry chemical or carbon dioxide.
UNUSUAL FIRE AND EXPLOSION HAZARDS: There is a possibility of pressure buildup in closed containers
when heated. Water spray may be used to cool the containers.
SPECIAL FIRE FIGHTING INSTRUCTIONS: Persons exposed to products of combustion should wear self-
contained breathing apparatus and full protective equipment.
HAZARDOUS COMBUSTION PRODUCTS: Carbon dioxide, Carbon monoxide

SECTION 6: ACCIDENTAL RELEASE MEASURES

SPECIAL PROTECTION: Exposure to the spilled material may be severely irritating or toxic.
Follow personal protective equipment recommendations found in
Section 8 of this MSDS. Personal protective equipment needs must be
evaluated based on information provided on this sheet and the special
circumstances created by the spill including; the material spilled, the
quantity of the spill, and the area in which the spill occurred. Never
exceed any occupational exposure limits.
METHODS FOR CLEAN-UP: Dike if necessary, contain spill with inert absorbent and transfer to
containers for disposal. Keep spilled product out of sewers, watersheds,
or water systems.
Contain spill, dilute if necessary and neutralize. Remove with inert
absorbent.

Transport Emergency Phone Number (CHEMTREC): 1-800-424-9300

SECTION 7: HANDLING AND STORAGE

Handling: Avoid contacting and avoid breathing the material. Use only in a well ventilated
area. Aluminum is not an acceptable material of construction for pumps, mixers,
fittings or storage for this product.
Page 3 of 6

FOSTER 81-27 Q
Print Date: 06-01-2015 802389PM
SAFETY DATA SHEET
______________________________________________________________________________
Storage: Store in a cool, dry place.Protect from freezing
Consult the Technical Data Sheet for specific storage instructions.

SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION


EXPOSURE LIMITS:
Chemical Name Note ACGIH EXPOSURE LIMITS OSHA PEL
Kaolin clay * (see 2 mg/m3 TWA (particulate matter 15 mg/m3 TWA (total dust); 5 mg/m3 TWA
below) containing no asbestos and <1% crystalline (respirable fraction)
silica, respirable fraction)

*This product contains one or more materials that may be hazardous when present as an airborne dust. During normal handling of the product, the
material is encapsulated within the product and will not present an exposure risk. Once the product has reached its final state and is abraded or
disturbed, dusting and exposure may occur.

ENGINEERING CONTROL METHODS:

VENTILATION: Local exhaust ventilation or other engineering controls are normally


required when handling or using this product to avoid overexposure.
EYE PROTECTION: Wear chemical splash goggles when handling this product.
Additionally, wear a face shield when the possibility of splashing of
liquid exists. Do not wear contact lenses. Have an eye wash station
available.
SKIN PROTECTION: Prevent contact with this product. Wear chemically resistant gloves,
long sleeved shirt, an apron, and other protective equipment
depending on conditions of use.
GLOVES: Butyl rubber
RESPIRATORY PROTECTION: Respiratory protection will be required when ventilation or other
engineering controls can not reduce the exposure to acceptable levels.
NIOSH approved air purifying respirator with dust/mist filter if
product is sprayed.
Respirators should be selected by and used following requirements
found in OSHA's respirator standard (29 CFR 1910.134).

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES


PHYSICAL STATE: Liquid
COLOR: Beige
ODOR: Earthy
ODOR THRESHOLD: Not established
pH: Not established
FREEZING/MELTING POINT (deg. C): Not established
BOILING POINT (deg. C): Not established
FLASH POINT: Non flammable
EVAPORATION RATE: Not established
FLAMMABILITY: Not a flammable solid or gas
UPPER EXPLOSIVE LIMIT (% in air): Not established
LOWER EXPLOSIVE LIMIT (% in air): Not established
VAPOR PRESSURE (mm Hg): Not established
VAPOR DENSITY: Not established
WEIGHT PER GALLON (lbs.): 13.80
SPECIFIC GRAVITY: 1.660
SOLUBILITY: Not established
OCTANOL/WATER COEFFICIENT: Not established
Page 4 of 6

FOSTER 81-27 Q
Print Date: 06-01-2015 802389PM
SAFETY DATA SHEET
______________________________________________________________________________
AUTOIGNITION TEMPERATURE: Not established
DECOMPOSITION TEMPERATURE: Not established
VISCOSITY: No data available.
SOLIDS (% by weight): 65.0
VOC, weight percent 0.00
VOC, U.S. EPA Method 24, less water and exempt 0g/liter of material
solvents (theoretically determined)

SECTION 10: STABILITY AND REACTIVITY

STABILITY: Stable under normal conditions.


CHEMICAL INCOMPATIBILITY: Aluminum alloys
HAZARDOUS POLYMERIZATION: Will not occur.
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon monoxide, carbon dioxide

SECTION 11: TOXICOLOGICAL INFORMATION

Component Toxicity / Toxicology Data:


COMPONENT NAME LD50/LC50
Sodium silicate ORAL LD50 RAT 1,153 MG/KG

This product is a mixture. Unless noted, the information below is based on components.
Skin corrosion / irritation: Contact causes severe skin irritation and possible burns.
Serious eye damage / irritation :Corrosive to eye tissue. Can cause severe irritation, tearing, and burns that can
quickly lead to permanent injury including blindness.
Respiratory / skin sensitization: No data available.
Germ cell mutagenicity: No data available.
Carcinogenicity: No data available.
Reproductive toxicity: No data available.
Specific target organ toxicity-single exposure: No data available.
Respiratory irritation / Narcotic effects: No data available.
Specific target organ toxicity-repeated exposure: No data available.
Target organs potentially affected by exposure: Lungs
Aspiration hazard: No data available.

Medical Conditions Aggravated by Exposure: Lung disease

SECTION 12: ECOLOGICAL INFORMATION

OVERVIEW: No ecological information available for this product.


MOBILITY: No data available.
PERSISTENCE: No data available.
BIOACCUMULATION: No data available.

This product has not been tested for ecological effects. Relevant information for components is listed below:

Component:
: Ecotoxicity values:
Sodium silicate Acute Toxicity (Fish): 96 Hr LC50 Lepomis macrochirus: 301 - 478 mg/L; 96 Hr LC50
Page 5 of 6

FOSTER 81-27 Q
Print Date: 06-01-2015 802389PM
SAFETY DATA SHEET
______________________________________________________________________________
Brachydanio rerio: 3185 mg/L [semi-static]
Acute Toxicity (Daphnia): Not established
Acute Toxicity (Algae): Not established

SECTION 13: DISPOSAL CONSIDERATIONS


This product meets the definition of hazardous waste under the U.S. EPA Hazardous Waste Regulations 40 CFR
261. It is corrosive waste class D002. We recommend the required corrosivity testing on product to determine the
appropriate waste category. Disposal via incineration is recommended. Consult your state, local, or provincial
authorities for more restrictive requirements.
SECTION 14: TRANSPORT INFORMATION
Consult Bill of Lading for transportation information.

US DOT: NOT REGULATED


IATA: NOT REGULATED

SECTION 15: REGULATORY INFORMATION

INVENTORY STATUS
U.S. EPA TSCA: This product is in compliance with the Toxic Substances Control Act's
Inventory requirements.
CANADIAN CEPA DSL: The components of this product are included on the DSL or are exempt
from DSL requirements.
EUROPEAN REACH: As a result of the introduction of REACH into Europe, this product
cannot be imported into Europe unless the REACH requirements are
met.
AUSTRALIA AICS: This product is in compliance with the Australian Inventory of
Chemical Substances requirements.
JAPAN ENCS: This product is in compliance with the Japanese Existing and New
Chemical Substances requirements.
KOREAN TCCL: This product is in compliance with the Korean Existing Chemicals List
requirements.
PHILIPPINES: This product is in compliance with the Philippine Inventory of
Chemicals and Chemical Substances requirements.
CHINA IECSC INVENTORY: This product is in compliance with the Inventory of Existing Chemical
Substances in China (IECSC) requirements.
If you need more information about the inventory status of this product call 651-236-5858.

This product may contain chemical substances that are regulated for export by various government agencies (such as
the Environmental Protection Agency, the Bureau of Industry and Security, or the Drug Enforcement
Administration, among others). Before exporting this product from the USA or Canada, we recommend you contact
us at reg.request@hbfuller.com to request an export review.

FEDERAL REPORTING
EPA SARA Title III Section 313
Unless listed below, this product does not contain toxic chemical(s) subject to the reporting requirements of section
313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 (SARA) and 40 CFR part 372. EPA
has advised that when a percentage range is listed the midpoint may be used to fulfill reporting obligations.
Chemical Name CAS# %

WHMIS STATUS: Unless listed below, this product is not controlled under the Canadian Workplace Hazardous
Materials Information System.
D2B
Page 6 of 6

FOSTER 81-27 Q
Print Date: 06-01-2015 802389PM
SAFETY DATA SHEET
______________________________________________________________________________
E

STATE REPORTING
Proposition 65, The Safe Drinking Water and Toxic Enforcement Act of 1986:
Unless listed below, this product does not contain known levels of any chemical known to the State of California to
cause cancer or reproductive harm.
Chemical Name/List CAS Percent
Quartz (Carcinogen) 14808-60-7 0.01 - 0.1
Nickel (Carcinogen) 7440-02-0 < 10 ppm
Lead (Carcinogen) 7439-92-1 < 10 ppm
Lead (Developmental toxin) 7439-92-1 < 10 ppm
Lead (Female reproductive toxin) 7439-92-1 < 10 ppm
Lead (Male reproductive toxin) 7439-92-1 < 10 ppm

Substances of Very High Concern (SVHC) Content:


Unless listed below, this product does not contain SVHC’s.

SECTION 16: OTHER INFORMATION

SDS VERSION DATE: 03-16-2015

This Safety Data Sheet is prepared to comply with the United States Occupational Safety and Health Administration
(OSHA) Hazard Communication Standard (29 CFR 1910.1200) and the Canadian Workplace Hazardous Materials
Information System (WHMIS).
HMIS RATING: HEALTH -- 3 FLAMMABILITY -- 0 REACTIVITY -- 0
See SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION for personal protective equipment
recommendations.

Prepared by: The Global Regulatory Department


Phone: 651-236-5842

The information and recommendations set forth herein are believed to be accurate. Because some of the information
is derived from information provided to H.B.Fuller Construction Products, Inc. from its suppliers, and because
H.B.Fuller Construction Products, Inc. has no control over the conditions of handling and use, H.B.Fuller
Construction Products, Inc. makes no warranty, expressed or implied, regarding the accuracy of the data or the
results to be obtained from the use thereof. The information is supplied solely for your information and
consideration, and H.B.Fuller Construction Products, Inc. assumes no responsibility for use or reliance thereon. It is
the responsibility of the user of H.B.Fuller Construction Products, Inc. products to comply with all applicable
federal, state and local laws and regulations.

You might also like