Cable Glands
Cable Glands
Cable Glands
Section Index
I Cable Management System
816
Case
Polyamide
Split Grommet
TPE
Grommet (Cable
Product Code Grommet Size Cable Size Description IP-65 Mount
Holder) Material
DCHS-150-G20-10 TPE As Per Requirment As Per Requirment Terminated Holding System CD-32-M5
IP-65 Mount, to be ordered separaely
The Cable Terminated Holding System is designed for holding pre-assembled cables, pneumatic, hydraulic hose tubes and electrical
conduits in junction boxes, control cabinets etc. These products are a cost saving alternative to cable gland fitting.
Holder
Polyamide
Case
Polyamide
Split Grommet
TPE
Grommet (Cable
Product Code Grommet Size Cable Size Description IP-65 Mount
Holder) Material
DCHS-150-G42-1/G20-6 TPE As Per Requirment As Per Requirment Terminated Holding System CD-32-M5
IP-65 Mount, to be ordered separaely
The Cable Terminated Holding System is designed for holding pre-assembled cables, pneumatic, hydraulic hose tubes and electrical
conduits in junction boxes, control cabinets etc. These products are a cost saving alternative to cable gland fitting.
43 10
For
60
32
42
M5
58 16
75 17.5
2 5.5
36
32
9 40
58
Cut Out
Grommet (Cable
Product Code Grommet Size Cable Size Description IP-65 Mount
Holder) Material
DCHS-75-G42-1 TPE As Per Requirment As Per Requirment Terminated Holding System CD-32-M5
IP-65 Mount, to be ordered separaely
The Cable Terminated Holding System is designed for holding pre-assembled cables, pneumatic, hydraulic hose tubes and electrical
conduits in junction boxes, control cabinets etc. These products are a cost saving alternative to cable gland fitting.
43 10
For
42
M5
60
32
58 16
75 17.5
2 5.5
32
36
9 40
58
Cut Out
Grommet (Cable
Product Code Grommet Size Cable Size Description IP-65 Mount
Holder) Material
DCHS-75-G20-4 TPE As Per Requirment As Per Requirment Terminated Holding System CD-32-M5
IP-65 Mount, to be ordered separaely
The Cable Terminated Holding System is designed for holding pre-assembled cables, pneumatic, hydraulic hose tubes and electrical
conduits in junction boxes, control cabinets etc. These products are a cost saving alternative to cable gland fitting.
20.8
41.8
Case
Polyamide
FIPFG
Gasket
FIPFG
Gasket
112 10
For M5
60
32
42
130 16
150
130
9 112
2
36
32
5.5
Cut out
Product Code Cable Holder Material Cable Size Description IP-65 Mount
DCPS-150-A12/B5 Silicon Ø4.0 to Ø7.0 & Ø8.0 to Ø12.0 Cable Push System CD-32-M5
IP-65 Mount, to be ordered separaely
The Cable Push System is two plates along with a silicon mat in which conduits, cables, pneumatic and hydraulic hoses can be simply
pushed through the thin membrane and are immediately held in.
Case
Polyamide
Fascia Plate Mat Fascia Plate
Polyamide Silicon Polyamide
FIPFG
Gasket
112 10
For M5
60
32
42
130
16
150
130
9 112
2
36
32
5.5
Cut out
Product Code Cable Holder Material Cable Size Description IP-65 Mount
DCPS-150-A24 Silicon Ø4.0 to Ø7.0 Cable Push System CD-32-M5
IP-65 Mount, to be ordered separaely
The Cable Push System is two plates along with a silicon mat in which conduits, cables, pneumatic and hydraulic hoses can be simply
pushed through the thin membrane and are immediately held in.
Case
Polyamide
Fascia Plate
Fascia Plate Mat Polyamide
Polyamide Silicon
FIPFG
FIPFG Gasket
Gasket
112 10
For M5
60
32
42
130
16
150
130
9 112
2
36
32
5.5
Cut out
Product Code Cable Holder Material Cable Size Description IP-65 Mount
DCPS-150-B12 Silicon Ø8.0 to Ø12.0 Cable Push System CD-32-M5
IP-65 Mount, to be ordered separaely
The Cable Push System is two plates along with a silicon mat in which conduits, cables, pneumatic and hydraulic hoses can be simply
pushed through the thin membrane and are immediately held in.
Case
Polyamide
Fascia Plate
Mat Polyamide
Fascia Plate
Silicon
Polyamide
FIPFG
Gasket
A 43 B 10
For
60
32
M5
42
58
16
75
2 5.5
36
32
9 40
58
Cut Out
Product Code Cable Holder Material Cable Size Description IP-65 Mount
DCPS-75-A4/B5 Silicon Ø4.0 to Ø7.0 & Ø8.0 to Ø12.0 Cable Push System CD-32-M5
IP-65 Mount, to be ordered separaely
The Cable Push System is two plates along with a silicon mat in which conduits, cables, pneumatic and hydraulic hoses can be simply
pushed through the thin membrane and are immediately held in.
1
Holder
2
Insert the Pre-terminated Cable in the Split Grommet
3
Place the Grommet along with the Cable in the Holder
4
Close the Holders together
5
Place the Holder assembly in the Case
6
Place the Holder assembly in the Case